
| SNMPv2-TC | SNMPv2-SMI | Brocade-TC |
| Brocade-REG-MIB |
| sw | 1.3.6.1.4.1.1588.2.1.1.1 | ||
| The OID sub-tree for Brocade's Silkworm Series of Fibre Channel Switches. | |||
| OBJECT-IDENTITY | |||
| swTrapsV2 | 1.3.6.1.4.1.1588.2.1.1.1.0 | ||
| The Traps for Brocade's Fibre Channel Switch. | |||
| OBJECT-IDENTITY | |||
| swFault | 1.3.6.1.4.1.1588.2.1.1.1.0.1 | ||
| Obsoleted this trap as firmware doesn't support this trap. A swFault(1) is generated whenever the diagnostics detects a fault with the switch. | |||
| NOTIFICATION-TYPE | |||
| swDiagResult | |||
| swSsn | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swSensorScn | 1.3.6.1.4.1.1588.2.1.1.1.0.2 | ||
| A swSensorScn(2) is generated whenever an environment sensor changes its operational state. For instance, a fan stop working. The VarBind in the Trap Data Unit shall contain the corresponding instance of the sensor status, sensor index, sensor type, sensor value (reading) and sensor information. Note that the sensor information contains the type of sensor and its number in textual format. | |||
| NOTIFICATION-TYPE | |||
| swSensorStatus | |||
| swSensorIndex | |||
| swSensorType | |||
| swSensorValue | |||
| swSensorInfo | |||
| swSsn | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swFCPortScn | 1.3.6.1.4.1.1588.2.1.1.1.0.3 | ||
| A swFCPortScn(3) is generated whenever an FC_Port changes its operational state. For instance, the FC_Port goes from on-line to offline. The VarBind in the Trap Data Unit shall contain the corresponding instance of the FC_Port's operational status, index, swFCPortName,swSsn and swFCPortFlag. swSsn is optional varbind sent when swExtTrap is also enabled. The three arguments swGroupName, swGroupType, swGroupMemPos belong to swGroup table which is obsolete and not implemented. | |||
| NOTIFICATION-TYPE | |||
| swFCPortOpStatus | |||
| swFCPortIndex | |||
| swFCPortName | |||
| swSsn | |||
| swFCPortFlag | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swEventTrap | 1.3.6.1.4.1.1588.2.1.1.1.0.4 | ||
| This trap is generated when an event whose level at or below swEventTrapLevel occurs. | |||
| NOTIFICATION-TYPE | |||
| swEventIndex | |||
| swEventTimeInfo | |||
| swEventLevel | |||
| swEventRepeatCount | |||
| swEventDescr | |||
| swSsn | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swFabricWatchTrap | 1.3.6.1.4.1.1588.2.1.1.1.0.5 | ||
| trap to be sent by Fabric Watch to notify of an event | |||
| NOTIFICATION-TYPE | |||
| swFwClassAreaIndex | |||
| swFwThresholdIndex | |||
| swFwName | |||
| swFwLabel | |||
| swFwLastEventVal | |||
| swFwLastEventTime | |||
| swFwLastEvent | |||
| swFwLastState | |||
| swFwLastSeverityLevel | |||
| swSsn | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swTrackChangesTrap | 1.3.6.1.4.1.1588.2.1.1.1.0.6 | ||
| trap to be sent for tracking login/logout/config changes | |||
| NOTIFICATION-TYPE | |||
| swTrackChangesInfo | |||
| swSsn | |||
| swGroupName | |||
| swGroupType | |||
| swGroupMemPos | |||
| swSystem | 1.3.6.1.4.1.1588.2.1.1.1.1 | ||
| The OID sub-tree for swSystem group. | |||
| OBJECT-IDENTITY | |||
| swCurrentDate | 1.3.6.1.4.1.1588.2.1.1.1.1.1 | ||
| The current date information in displayable textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swBootDate | 1.3.6.1.4.1.1588.2.1.1.1.1.2 | ||
| The date and time when the system last booted, in displayable textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swFWLastUpdated | 1.3.6.1.4.1.1588.2.1.1.1.1.3 | ||
| The information indicates the date when the firmware was last updated, in displayable textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swFlashLastUpdated | 1.3.6.1.4.1.1588.2.1.1.1.1.4 | ||
| The information indicates the date when the FLASH was last updated, in displayable textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swBootPromLastUpdated | 1.3.6.1.4.1.1588.2.1.1.1.1.5 | ||
| The information indicates the date when the boot PROM was last updated, in displayable textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swFirmwareVersion | 1.3.6.1.4.1.1588.2.1.1.1.1.6 | ||
| The current version of the firwmare. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..24) | ||
| swOperStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.7 | ||
| The current operational status of the switch. The states are as follow: o online(1) means the switch is accessible by an external Fibre Channel port; o offline(2) means the switch is not accessible; o testing(3) means the switch is in a built-in test mode and is not accessible by an external Fibre Channel port; o faulty(4) means the switch is not operational. | |||
| OBJECT-TYPE | |||
| INTEGER | online(1), offline(2), testing(3), faulty(4) | ||
| swAdmStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.8 | ||
| The desired administrative status of the switch. A management station may place the switch in a desired state by setting this object accordingly. The states are as follow: o online(1) means set the switch to be accessible by an external Fibre Channel port; o offline(2) means set the switch to be inaccessible; o testing(3) means set the switch to run the built-in test; o faulty(4) means set the switch to a 'soft' faulty condition; o reboot(5) means set the switch to reboot in 1 second. o fastboot(6) means set the switch to fastboot in 1 second. Fastboot would cause the switch to boot but skip over the POST. o switchReboot(7) means set the current switch to reboot in 1 second. When the switch is in faulty state, only two states can be set: faulty and reboot/fastboot/switchReboot. | |||
| OBJECT-TYPE | |||
| INTEGER | online(1), offline(2), testing(3), faulty(4), reboot(5), fastboot(6), switchReboot(7) | ||
| swTelnetShellAdmStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.9 | ||
| The desired administrative status of the Telnet shell. By setting it to terminated(1), the current Telnet shell task is deleted. When this variable instance is read, it reports the value last set through SNMP. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), terminated(1) | ||
| swSsn | 1.3.6.1.4.1.1588.2.1.1.1.1.10 | ||
| The soft serial number of the switch. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..128) | ||
| swFlashDLOperStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.11 | ||
| The operational status of the FLASH. The operational states are as follow: o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgraded(2) state indicates that it contains the image upgraded from the swFlashDLHost.0.; o swCfUploaded(3) state indicates that the switch configuration file has been uploaded to the host; and o swCfDownloaded(4) state indicates that the switch configuration file has been downloaded from the host. o swFwCorrupted (5) state indicates that the firmware in the FLASH of the switch is corrupted. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), swCurrent(1), swFwUpgraded(2), swCfUploaded(3), swCfDownloaded(4), swFwCorrupted(5) | ||
| swFlashDLAdmStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.12 | ||
| The desired state of the FLASH. A management station may place the FLASH in a desired state by setting this object accordingly: o swCurrent(1) indicates that the FLASH contains the current firmware image or config file; o swFwUpgrade(2) means that the firmware in the FLASH is to be upgraded from the host specified; o swCfUpload(3) means that the switch config file is to be uploaded to the host specified; or o swCfDownload(4) means that the switch config file is to be downloaded from the host specified. o swFwCorrupted(5) state indicates that the firmware in the FLASH is corrupted. This value is for informational purpose only. However, set of swFlashDLAdmStatus to this value is not allowed. The host is specified in swFlashDLHost.0. In addition, user name is specified in swFlashDLUser.0, and the file name specified in swFlashDLFile.0. Reference the user manual on the following commands, o firmwareDownload, o configUpload, and o configDownload. | |||
| OBJECT-TYPE | |||
| INTEGER | swCurrent(1), swFwUpgrade(2), swCfUpload(3), swCfDownload(4), swFwCorrupted(5) | ||
| swFlashDLHost | 1.3.6.1.4.1.1588.2.1.1.1.1.13 | ||
| The name or IP address (in dot notation) of the host to download or upload a relevant file to the FLASH. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swFlashDLUser | 1.3.6.1.4.1.1588.2.1.1.1.1.14 | ||
| The user name on the host to download or upload a relevant file to or from the FLASH. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swFlashDLFile | 1.3.6.1.4.1.1588.2.1.1.1.1.15 | ||
| The name of the file to be downloaded or uploaded. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swFlashDLPassword | 1.3.6.1.4.1.1588.2.1.1.1.1.16 | ||
| The password to be used in for FTP transfer of files in the download or upload operation. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..100) | ||
| swBeaconOperStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.18 | ||
| The current operational status of the switch beacon. When the beacon is on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off, each LED will be in their its regular status indicating color and state. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| swBeaconAdmStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.19 | ||
| The desired status of the switch beacon. When the beacon is set to on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is set to off, each LED will be in its regular status indicating color and state. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| swDiagResult | 1.3.6.1.4.1.1588.2.1.1.1.1.20 | ||
| The result of the power-on startup (POST) diagnostics. | |||
| OBJECT-TYPE | |||
| INTEGER | sw-ok(1), sw-faulty(2), sw-embedded-port-fault(3) | ||
| swNumSensors | 1.3.6.1.4.1.1588.2.1.1.1.1.21 | ||
| The number of sensors inside the switch. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swSensorTable | 1.3.6.1.4.1.1588.2.1.1.1.1.22 | ||
| The table of sensor entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwSensorEntry | |||
| swSensorEntry | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1 | ||
| An entry of the sensor information. | |||
| OBJECT-TYPE | |||
| SwSensorEntry | |||
| swSensorIndex | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.1 | ||
| This object identifies the sensor. | |||
| OBJECT-TYPE | |||
| SwSensorIndex | |||
| swSensorType | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2 | ||
| This object identifies the sensor type. | |||
| OBJECT-TYPE | |||
| INTEGER | temperature(1), fan(2), power-supply(3) | ||
| swSensorStatus | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3 | ||
| The current status of the sensor. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), faulty(2), below-min(3), nominal(4), above-max(5), absent(6) | ||
| swSensorValue | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4 | ||
| The current value (reading) of the sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. In V2.0, the temperature sensor value will be in Celsius; the fan value will be in RPM (revolution per minute); and the power supply sensor reading will be unknown. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| swSensorInfo | 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5 | ||
| Additional displayable information on the sensor. In V2.x, it contains the sensor type and number in textual format. For example, 'Temp 3', 'Fan 6'. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| swTrackChangesInfo | 1.3.6.1.4.1.1588.2.1.1.1.1.23 | ||
| Track changes string. For trap only | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swID | 1.3.6.1.4.1.1588.2.1.1.1.1.24 | ||
| The number of the logical switch (0/1) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| swEtherIPAddress | 1.3.6.1.4.1.1588.2.1.1.1.1.25 | ||
| The IP Address of the Ethernet interface of this logical switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swEtherIPMask | 1.3.6.1.4.1.1588.2.1.1.1.1.26 | ||
| The IP Mask of the Ethernet interface of this logical switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFCIPAddress | 1.3.6.1.4.1.1588.2.1.1.1.1.27 | ||
| The IP Address of the FC interface of this logical switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFCIPMask | 1.3.6.1.4.1.1588.2.1.1.1.1.28 | ||
| The IP Mask of the FC interface of this logical switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFabric | 1.3.6.1.4.1.1588.2.1.1.1.2 | ||
| The OID sub-tree for swFabric group. | |||
| OBJECT-IDENTITY | |||
| swDomainID | 1.3.6.1.4.1.1588.2.1.1.1.2.1 | ||
| The current Fibre Channel domain ID of the switch. To set a new value, the switch (swAdmStatus) must be in offline or testing state. | |||
| OBJECT-TYPE | |||
| SwDomainIndex | |||
| swPrincipalSwitch | 1.3.6.1.4.1.1588.2.1.1.1.2.2 | ||
| This object indicates whether the switch is the Principal switch as per FC-SW. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(1), no(2) | ||
| swNumNbs | 1.3.6.1.4.1.1588.2.1.1.1.2.8 | ||
| The number of Inter-Switch Links in the (immediate) neighborhood. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swNbTable | 1.3.6.1.4.1.1588.2.1.1.1.2.9 | ||
| This table contains the ISLs in the immediate neighborhood of the switch. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwNbEntry | |||
| swNbEntry | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1 | ||
| An entry containing each neighbor ISL parameters. | |||
| OBJECT-TYPE | |||
| SwNbEntry | |||
| swNbIndex | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.1 | ||
| This object identifies the neighbor ISL entry. | |||
| OBJECT-TYPE | |||
| SwNbIndex | |||
| swNbMyPort | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.2 | ||
| This is the port that has an ISL to another switch. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swNbRemDomain | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.3 | ||
| This is the Fibre Channel domain on the other end of the ISL. | |||
| OBJECT-TYPE | |||
| SwDomainIndex | |||
| swNbRemPort | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.4 | ||
| This is the port index on the other end of the ISL. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swNbBaudRate | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.5 | ||
| The baud rate of the ISL. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), oneEighth(2), quarter(4), half(8), full(16), double(32), quadruple(64), octuple(128), decuple(256) | ||
| swNbIslState | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.6 | ||
| The current state of the ISL. | |||
| OBJECT-TYPE | |||
| INTEGER | sw-init(1), sw-internal2(2), sw-internal3(3), sw-internal4(4), sw-active(5) | ||
| swNbIslCost | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.7 | ||
| The current link cost of the ISL. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swNbRemPortName | 1.3.6.1.4.1.1588.2.1.1.1.2.9.1.8 | ||
| The World_wide_Name of the remote port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swFabricMemTable | 1.3.6.1.4.1.1588.2.1.1.1.2.10 | ||
| This table contains information on the member switches of a fabric. This may not be available on all versions of Fabric OS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwFabricMemEntry | |||
| swFabricMemEntry | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1 | ||
| An entry containing each switch in the fabric. | |||
| OBJECT-TYPE | |||
| SwFabricMemEntry | |||
| swFabricMemWwn | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.1 | ||
| This object identifies the World wide name of the member switch. | |||
| OBJECT-TYPE | |||
| FcWwn | |||
| swFabricMemDid | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.2 | ||
| This object identifies the domain id of the member switch. | |||
| OBJECT-TYPE | |||
| SwDomainIndex | |||
| swFabricMemName | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.3 | ||
| This object identifies the name of the member switch. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| swFabricMemEIP | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.4 | ||
| This object identifies the ethernet IP address of the member switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFabricMemFCIP | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.5 | ||
| This object identifies the Fibre Channel IP address of the member switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFabricMemGWIP | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.6 | ||
| This object identifies the Gateway IP address of the member switch. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swFabricMemType | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.7 | ||
| This object identifies the member switch type. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFabricMemShortVersion | 1.3.6.1.4.1.1588.2.1.1.1.2.10.1.8 | ||
| This object identifies Fabric OS version of the member switch. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..24) | ||
| swIDIDMode | 1.3.6.1.4.1.1588.2.1.1.1.2.11 | ||
| Status of Insistent Domain ID (IDID) mode. Status indicating IDID mode is enabled or not. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2) | ||
| swModule | 1.3.6.1.4.1.1588.2.1.1.1.3 | ||
| The OID sub-tree for swModule group. | |||
| OBJECT-IDENTITY | |||
| swAgtCfg | 1.3.6.1.4.1.1588.2.1.1.1.4 | ||
| The OID sub-tree for swAgtCfg group. | |||
| OBJECT-IDENTITY | |||
| swAgtCmtyTable | 1.3.6.1.4.1.1588.2.1.1.1.4.11 | ||
| A table that contains, one entry for each Community, the access control and parameters of the Community. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwAgtCmtyEntry | |||
| swAgtCmtyEntry | 1.3.6.1.4.1.1588.2.1.1.1.4.11.1 | ||
| An entry containing the Community parameters. | |||
| OBJECT-TYPE | |||
| SwAgtCmtyEntry | |||
| swAgtCmtyIdx | 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.1 | ||
| This object identifies the SNMPv1 Community entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..6 | ||
| swAgtCmtyStr | 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.2 | ||
| This is a Community string supported by the agent. If a new value is set successfully, it takes effect immediately. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(2..16) | ||
| swAgtTrapRcp | 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.3 | ||
| This is the trap recipient associated with the Community. If a new value is set successfully, it takes effect immediately. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swAgtTrapSeverityLevel | 1.3.6.1.4.1.1588.2.1.1.1.4.11.1.4 | ||
| This is the trap severity level associated with the swAgtTrapRcp. The trap severity level in conjunction with the an event's severity level. When an event occurs and if its severity level is at or below the set value, the SNMP trap is sent to configured trap recipients. The severity level is limited to particular events. If a new value is set successfully, it takes effect immediately. | |||
| OBJECT-TYPE | |||
| SwSevType | |||
| swFCport | 1.3.6.1.4.1.1588.2.1.1.1.6 | ||
| The OID sub-tree for swFCport group. | |||
| OBJECT-IDENTITY | |||
| swFCPortCapacity | 1.3.6.1.4.1.1588.2.1.1.1.6.1 | ||
| The maximum number of Fibre Channel ports on this switch. It includes G_Port, F_Port, FL_Port and any other types of Fibre Channel port. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFCPortTable | 1.3.6.1.4.1.1588.2.1.1.1.6.2 | ||
| A table that contains, one entry for each switch port, configuration and service parameters of the port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwFCPortEntry | |||
| swFCPortEntry | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1 | ||
| An entry containing the configuration and service parameters of the switch port. | |||
| OBJECT-TYPE | |||
| SwFCPortEntry | |||
| swFCPortIndex | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1 | ||
| This object identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. E.g. port index 1 correspond to port number 0. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swFCPortType | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.2 | ||
| This object identifies the type of switch port. It may be of type stitch(1), flannel(2), loom(3) , bloom(4),rdbloom(5) or wormhole(6). | |||
| OBJECT-TYPE | |||
| INTEGER | stitch(1), flannel(2), loom(3), bloom(4), rdbloom(5), wormhole(6), other(7), unknown(8) | ||
| swFCPortPhyState | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3 | ||
| This object identifies the physical state of the port: noCard(1) no card present in this switch slot; noTransceiver(2) no Transceiver module in this port. noGbic(2) was used previously. Transceiver is the generic name for GBIC, SFP etc.; laserFault(3) the module is signaling a laser fault (defective Transceiver); noLight(4) the module is not receiving light; noSync(5) the module is receiving light but is out of sync; inSync(6) the module is receiving light and is in sync; portFault(7) the port is marked faulty (defective Transceiver, cable or device); diagFault(8) the port failed diagnostics (defective G_Port or FL_Port card or motherboard); lockRef(9) the port is locking to the reference signal. | |||
| OBJECT-TYPE | |||
| INTEGER | noCard(1), noTransceiver(2), laserFault(3), noLight(4), noSync(5), inSync(6), portFault(7), diagFault(8), lockRef(9) | ||
| swFCPortOpStatus | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4 | ||
| This object identifies the operational status of the port. The online(1) state indicates that user frames can be passed. The unknown(0) state indicates that likely the port module is physically absent (see swFCPortPhyState). | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(0), online(1), offline(2), testing(3), faulty(4) | ||
| swFCPortAdmStatus | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5 | ||
| The desired state of the port. A management station may place the port in a desired state by setting this object accordingly. The testing(3) state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swFCPortAdmStatus is then changed to either the online(1) or testing(3) states, or remains in the offline(2) state. | |||
| OBJECT-TYPE | |||
| INTEGER | online(1), offline(2), testing(3), faulty(4) | ||
| swFCPortLinkState | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.6 | ||
| This object indicates the link state of the port. The value may be: enabled(1) - port is allowed to participate in the FC-PH protocol with its attached port (or ports if it is in a FC-AL loop); disabled(2) - the port is not allowed to participate in the FC-PH protocol with its attached port(s); loopback(3) - the port may transmit frames through an internal path to verify the health of the transmitter and receiver path. Note that when the port's link state changes, its operational status (swFCPortOpStatus) will be affected. | |||
| OBJECT-TYPE | |||
| INTEGER | enabled(1), disabled(2), loopback(3) | ||
| swFCPortTxType | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.7 | ||
| This object indicates the media transmitter type of the port. The value may be: unknown(1) cannot determined to the port driver lw(2) long wave laser sw(3) short wave laser ld(4) long wave LED cu(5) copper (electrical). | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), lw(2), sw(3), ld(4), cu(5) | ||
| swFCPortTxWords | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11 | ||
| This object counts the number of Fibre Channel words that the port has transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxWords | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12 | ||
| This object counts the number of Fibre Channel words that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortTxFrames | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.13 | ||
| This object counts the number of (Fibre Channel) frames that the port has transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxFrames | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.14 | ||
| This object counts the number of (Fibre Channel) frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxC2Frames | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.15 | ||
| This object counts the number of Class 2 frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxC3Frames | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.16 | ||
| This object counts the number of Class 3 frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxLCs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.17 | ||
| This object counts the number of Link Control frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxMcasts | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.18 | ||
| This object counts the number of Multicast frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortTooManyRdys | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.19 | ||
| This object counts the number of times when RDYs exceeds the frames received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortNoTxCredits | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.20 | ||
| This object counts the number of times when the transmit credit has reached zero. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxEncInFrs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.21 | ||
| This object counts the number of encoding error or disparity error inside frames received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxCrcs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.22 | ||
| This object counts the number of CRC errors detected for frames received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxTruncs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.23 | ||
| This object counts the number of truncated frames that the port has received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxTooLongs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.24 | ||
| This object counts the number of received frames that are too long. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxBadEofs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.25 | ||
| This object counts the number of received frames that have bad EOF delimiter. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxEncOutFrs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.26 | ||
| This object counts the number of encoding error or disparity error outside frames received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortRxBadOs | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.27 | ||
| This object counts the number of invalid Ordered Sets received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortC3Discards | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.28 | ||
| This object counts the number of Class 3 frames that the port has discarded. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortMcastTimedOuts | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.29 | ||
| This object counts the number of Multicast frames that has been timed out. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortTxMcasts | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.30 | ||
| This object counts the number of Multicast frames that has been transmitted. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortLipIns | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.31 | ||
| This object counts the number of Loop Initializations that has been initiated by loop devices attached. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortLipOuts | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.32 | ||
| This object counts the number of Loop Initializations that has been initiated by the port. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swFCPortLipLastAlpa | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.33 | ||
| This object indicates the Physical Address (AL_PA) of the loop device that initiated the last Loop Initialization. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| swFCPortWwn | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.34 | ||
| The World_wide_Name of the Fibre Channel port. The contents of an instance are in the IEEE extended format as specified in FC-PH; the 12-bit port identifier represents the port number within the switch. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swFCPortSpeed | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.35 | ||
| The desired baud rate for the port. It can have the values of 1GB (1), 2GB (2), Auto-Negotiate (3), 4GB (4), 8GB (5), or 10GB (6). Some of the above values may not be supported by all type of switches. | |||
| OBJECT-TYPE | |||
| INTEGER | one-GB(1), two-GB(2), auto-Negotiate(3), four-GB(4), eight-GB(5), ten-GB(6) | ||
| swFCPortName | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36 | ||
| A string indicates the name of the addressed port. The names should be persistent across switch reboots. Port names do not have to be unique within a switch or within a fabric. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| swFCPortSpecifier | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.37 | ||
| This string indicates the physical port number of the addressed port. The format of the string is: /port, where 'slot' being present only for bladed systems. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swFCPortFlag | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.38 | ||
| A bit map of port status flags which includes the information of port type. Currently this will indicate if the port is virtual or physical. | |||
| OBJECT-TYPE | |||
| FcPortFlag | |||
| swFCPortBrcdType | 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.39 | ||
| The Brocade port type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), other(2), fl-port(3), f-port(4), e-port(5), g-port(6), ex-port(7) | ||
| swNs | 1.3.6.1.4.1.1588.2.1.1.1.7 | ||
| The OID sub-tree for swNs group. | |||
| OBJECT-IDENTITY | |||
| swNsLocalNumEntry | 1.3.6.1.4.1.1588.2.1.1.1.7.1 | ||
| The number of local Name Server entries. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swNsLocalTable | 1.3.6.1.4.1.1588.2.1.1.1.7.2 | ||
| The table of local Name Server entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwNsEntry | |||
| swNsLocalEntry | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1 | ||
| An entry of the local Name Server database. | |||
| OBJECT-TYPE | |||
| SwNsEntry | |||
| swNsEntryIndex | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.1 | ||
| The object identifies the Name Server database entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swNsPortID | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.2 | ||
| The object identifies the Fibre Channel port address ID of the entry. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| swNsPortType | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.3 | ||
| The object identifies the type of port: N_Port, NL_Port, etc., for this entry. The type is defined in FC-GS-2. | |||
| OBJECT-TYPE | |||
| INTEGER | nPort(1), nlPort(2) | ||
| swNsPortName | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.4 | ||
| The object identifies the Fibre Channel World_wide Name of the port entry. | |||
| OBJECT-TYPE | |||
| FcWwn | |||
| swNsPortSymb | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.5 | ||
| The object identifies the contents of a Symbolic Name of the port entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 255 bytes, and the first byte of the array specifies the length of its 'contents'. This object variable corresponds to the 'contents' of the Symbolic Name, without the first byte. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..255) | ||
| swNsNodeName | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.6 | ||
| The object identifies the Fibre Channel World_wide Name of the associated node as defined in FC-GS-2. | |||
| OBJECT-TYPE | |||
| FcWwn | |||
| swNsNodeSymb | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.7 | ||
| The object identifies the contents of a Symbolic Name of the the node associated with the entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 255 bytes, and the first byte of the array specifies the length of its 'contents'. This object variable corresponds to the 'contents' of the Symbolic Name, without the first byte (specifying the length). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..255) | ||
| swNsIPA | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.8 | ||
| The object identifies the Initial Process Associator of the node for the entry as defined in FC-GS-2. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swNsIpAddress | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.9 | ||
| The object identifies the IP address of the node for the entry as defined in FC-GS-2. The format of the address is in IPv6. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swNsCos | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.10 | ||
| The object identifies the class of services supported by the port. The value is a bit-map defined as follows: o bit 0 is class F, o bit 1 is class 1, o bit 2 is class 2, o bit 3 is class 3, o bit 4 is class 4, etc. | |||
| OBJECT-TYPE | |||
| INTEGER | class-F(1), class-1(2), class-F-1(3), class-2(4), class-F-2(5), class-1-2(6), class-F-1-2(7), class-3(8), class-F-3(9), class-1-3(10), class-F-1-3(11), class-2-3(12), class-F-2-3(13), class-1-2-3(14), class-F-1-2-3(15) | ||
| swNsFc4 | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.11 | ||
| The object identifies the FC-4s supported by the port as defined in FC-GS-2. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(32) | ||
| swNsIpNxPort | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.12 | ||
| The object identifies IpAddress of the Nx_port for the entry. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(16) | ||
| swNsWwn | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.13 | ||
| The object identifies the World Wide Name (WWN) of the Fx_port for the entry. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swNsHardAddr | 1.3.6.1.4.1.1588.2.1.1.1.7.2.1.14 | ||
| The object identifies the 24-bit hard address of the node for the entry. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(3) | ||
| swEvent | 1.3.6.1.4.1.1588.2.1.1.1.8 | ||
| The OID sub-tree for swEvent group. | |||
| OBJECT-IDENTITY | |||
| swEventTrapLevel | 1.3.6.1.4.1.1588.2.1.1.1.8.1 | ||
| swAgtTrapSeverityLevel, in absence of swEventTrapLevel, specifies the Trap Severity Level of each defined trap recipient host. This object specifies the swEventTrap level in conjunction with an event's severity level. When an event occurs and if its severity level is at or below the value specified by this object instance, the agent will send the associated swEventTrap to configured recipients. | |||
| OBJECT-TYPE | |||
| INTEGER | none(0), critical(1), error(2), warning(3), informational(4), debug(5) | ||
| swEventNumEntries | 1.3.6.1.4.1.1588.2.1.1.1.8.4 | ||
| The number of entries in the Event Table. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEventTable | 1.3.6.1.4.1.1588.2.1.1.1.8.5 | ||
| The table of event entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwEventEntry | |||
| swEventEntry | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1 | ||
| An entry of the event table. | |||
| OBJECT-TYPE | |||
| SwEventEntry | |||
| swEventIndex | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.1 | ||
| This object identifies the event entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEventTimeInfo | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.2 | ||
| This object identifies the date and time when this event occurred, in textual format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swEventLevel | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.3 | ||
| This object identifies the severity level of this event entry. | |||
| OBJECT-TYPE | |||
| INTEGER | critical(1), error(2), warning(3), informational(4), debug(5) | ||
| swEventRepeatCount | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.4 | ||
| This object identifies how many times this particular event has occurred. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEventDescr | 1.3.6.1.4.1.1588.2.1.1.1.8.5.1.5 | ||
| This object identifies the textual description of the event. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swFwSystem | 1.3.6.1.4.1.1588.2.1.1.1.10 | ||
| The OID sub-tree for swFwSystem group. | |||
| OBJECT-IDENTITY | |||
| swFwFabricWatchLicense | 1.3.6.1.4.1.1588.2.1.1.1.10.1 | ||
| tells if licensed or not. | |||
| OBJECT-TYPE | |||
| SwFwLicense | |||
| swFwClassAreaTable | 1.3.6.1.4.1.1588.2.1.1.1.10.2 | ||
| The table of classes and areas. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwFwClassAreaEntry | |||
| swFwClassAreaEntry | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1 | ||
| An entry of the classes and areas. | |||
| OBJECT-TYPE | |||
| SwFwClassAreaEntry | |||
| swFwClassAreaIndex | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.1 | ||
| This object identifies the class type. | |||
| OBJECT-TYPE | |||
| SwFwClassesAreas | |||
| swFwWriteThVals | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.2 | ||
| This object is set to apply the value changes. | |||
| OBJECT-TYPE | |||
| SwFwWriteVals | |||
| swFwDefaultUnit | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.3 | ||
| A Default unit string name for a threshold area. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swFwDefaultTimebase | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.4 | ||
| A Default timebase for the current threshold counter. | |||
| OBJECT-TYPE | |||
| SwFwTimebase | |||
| swFwDefaultLow | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.5 | ||
| A Default low threshold value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwDefaultHigh | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.6 | ||
| A Default high threshold value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwDefaultBufSize | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.7 | ||
| A Default buffer size value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwCustUnit | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.8 | ||
| A custom unit string name for a threshold area. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swFwCustTimebase | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.9 | ||
| A custom timebase for the current threshold counter. | |||
| OBJECT-TYPE | |||
| SwFwTimebase | |||
| swFwCustLow | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.10 | ||
| A custom low threshold value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwCustHigh | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.11 | ||
| A custom high threshold value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwCustBufSize | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.12 | ||
| A custom buffer size value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwThLevel | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.13 | ||
| A level where all the threshold values are set at. | |||
| OBJECT-TYPE | |||
| SwFwLevels | |||
| swFwWriteActVals | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.14 | ||
| This object is set to apply act value changes. | |||
| OBJECT-TYPE | |||
| SwFwWriteVals | |||
| swFwDefaultChangedActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.15 | ||
| Default action matrix for changed event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwDefaultExceededActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.16 | ||
| Default action matrix for exceeded event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwDefaultBelowActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.17 | ||
| Default action matrix for below event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwDefaultAboveActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.18 | ||
| Default action matrix for above event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwDefaultInBetweenActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.19 | ||
| Default action matrix for in-between event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwCustChangedActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.20 | ||
| custom action matrix for changed event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwCustExceededActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.21 | ||
| custom action matrix for exceeded event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwCustBelowActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.22 | ||
| custom action matrix for below event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwCustAboveActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.23 | ||
| custom action matrix for above event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwCustInBetweenActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.24 | ||
| custom action matrix for in-between event. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwValidActs | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.25 | ||
| matrix of valid acts for an class/area. | |||
| OBJECT-TYPE | |||
| SwFwActs | |||
| swFwActLevel | 1.3.6.1.4.1.1588.2.1.1.1.10.2.1.26 | ||
| A level where all the actions are set at. | |||
| OBJECT-TYPE | |||
| SwFwLevels | |||
| swFwThresholdTable | 1.3.6.1.4.1.1588.2.1.1.1.10.3 | ||
| The table of individual thresholds. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwFwThresholdEntry | |||
| swFwThresholdEntry | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1 | ||
| An entry of an individual threshold. | |||
| OBJECT-TYPE | |||
| SwFwThresholdEntry | |||
| swFwThresholdIndex | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.1 | ||
| This object identifies the element index of an threshold. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwStatus | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.2 | ||
| This object identifies if an threshold is enabled or disabled. | |||
| OBJECT-TYPE | |||
| SwFwStatus | |||
| swFwName | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.3 | ||
| This object is a name of the threshold. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| swFwLabel | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.4 | ||
| This object is a label of the threshold. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..70) | ||
| swFwCurVal | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.5 | ||
| This object is a current counter of the threshold. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwLastEvent | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.6 | ||
| This object is a last event type of the threshold. | |||
| OBJECT-TYPE | |||
| SwFwEvent | |||
| swFwLastEventVal | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.7 | ||
| This object is a last event value of the threshold. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwLastEventTime | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.8 | ||
| This object is a last event time of the threshold. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| swFwLastState | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.9 | ||
| This object is a last event state of the threshold. | |||
| OBJECT-TYPE | |||
| SwFwState | |||
| swFwBehaviorType | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.10 | ||
| A behavior of which the thresholds generate event. | |||
| OBJECT-TYPE | |||
| SwFwBehavior | |||
| swFwBehaviorInt | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.11 | ||
| A integer of which the thresholds generate continuous event. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swFwLastSeverityLevel | 1.3.6.1.4.1.1588.2.1.1.1.10.3.1.12 | ||
| This object is a last event severity level of the threshold. | |||
| OBJECT-TYPE | |||
| SwSevType | |||
| swEndDevice | 1.3.6.1.4.1.1588.2.1.1.1.21 | ||
| The OID sub-tree for swEndDevice group. | |||
| OBJECT-IDENTITY | |||
| swEndDeviceRlsTable | 1.3.6.1.4.1.1588.2.1.1.1.21.1 | ||
| The table of individual end devices' rls. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwEndDeviceRlsEntry | |||
| swEndDeviceRlsEntry | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1 | ||
| An entry of an individual end devices' rls. | |||
| OBJECT-TYPE | |||
| SwEndDeviceRlsEntry | |||
| swEndDevicePort | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.1 | ||
| This object identifies the port of the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceAlpa | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.2 | ||
| This object identifies the alpa of the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDevicePortID | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.3 | ||
| The object identifies the Fibre Channel port address ID of the entry. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| swEndDeviceLinkFailure | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.4 | ||
| Link failure count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceSyncLoss | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.5 | ||
| Sync loss count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceSigLoss | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.6 | ||
| Sig loss count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceProtoErr | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.7 | ||
| Protocol err count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceInvalidWord | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.8 | ||
| Invalid word count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swEndDeviceInvalidCRC | 1.3.6.1.4.1.1588.2.1.1.1.21.1.1.9 | ||
| Invalid CRC count for the end device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swGroup | 1.3.6.1.4.1.1588.2.1.1.1.22 | ||
| The OID sub-tree for swGroup group. | |||
| OBJECT-IDENTITY | |||
| swGroupTable | 1.3.6.1.4.1.1588.2.1.1.1.22.1 | ||
| The table of groups. This may not be available on all versions of Fabric OS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwGroupEntry | |||
| swGroupEntry | 1.3.6.1.4.1.1588.2.1.1.1.22.1.1 | ||
| An entry of table of groups. | |||
| OBJECT-TYPE | |||
| SwGroupEntry | |||
| swGroupIndex | 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.1 | ||
| This object is the group index starting from 1. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swGroupName | 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.2 | ||
| This object identifies the name of the group. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..32) | ||
| swGroupType | 1.3.6.1.4.1.1588.2.1.1.1.22.1.1.3 | ||
| This object identifies the type of the group. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..15) | ||
| swGroupMemTable | 1.3.6.1.4.1.1588.2.1.1.1.22.2 | ||
| The table of members of all groups. This may not be available on all versions of Fabric OS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwGroupMemEntry | |||
| swGroupMemEntry | 1.3.6.1.4.1.1588.2.1.1.1.22.2.1 | ||
| An entry for a member of a group. | |||
| OBJECT-TYPE | |||
| SwGroupMemEntry | |||
| swGroupId | 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.1 | ||
| This object identifies the Group Id of the member switch. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swGroupMemWwn | 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.2 | ||
| This object identifies the WWN of the member switch. | |||
| OBJECT-TYPE | |||
| FcWwn | |||
| swGroupMemPos | 1.3.6.1.4.1.1588.2.1.1.1.22.2.1.3 | ||
| This object identifies position of the member switch in the group. This is based on the order that the switches were added in the group. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swBlmPerfMnt | 1.3.6.1.4.1.1588.2.1.1.1.23 | ||
| The OID sub-tree for swBlmPerfMnt (Bloom Performance Monitor) group. | |||
| OBJECT-IDENTITY | |||
| swBlmPerfALPAMntTable | 1.3.6.1.4.1.1588.2.1.1.1.23.1 | ||
| ALPA monitoring counter Table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwBlmPerfALPAMntEntry | |||
| swBlmPerfALPAMntEntry | 1.3.6.1.4.1.1588.2.1.1.1.23.1.1 | ||
| ALPA monitoring counter for given ALPA. | |||
| OBJECT-TYPE | |||
| SwBlmPerfALPAMntEntry | |||
| swBlmPerfAlpaPort | 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.1 | ||
| This Object identifies the port index of the switch. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swBlmPerfAlpaIndx | 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.2 | ||
| This Object identifies the ALPA index. There can be 126 ALPA values | |||
| OBJECT-TYPE | |||
| Integer32 | 1..126 | ||
| swBlmPerfAlpa | 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.3 | ||
| This Object identifies the ALPA values. These values range between x'01' and x'EF'(1 to 239). ALPA value x'00' is reserved for FL_Port If Alpa device is invalid, then it will have -1 value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swBlmPerfAlpaCRCCnt | 1.3.6.1.4.1.1588.2.1.1.1.23.1.1.4 | ||
| Get CRC count for given ALPA and port. This monitoring provides information on the number of CRC errors occurred on the frames destined to each possible ALPA attached to a specific port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swBlmPerfEEMntTable | 1.3.6.1.4.1.1588.2.1.1.1.23.2 | ||
| End-to-End monitoring counter Table | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwBlmPerfEEMntEntry | |||
| swBlmPerfEEMntEntry | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1 | ||
| End-to-End monitoring counter for given port. | |||
| OBJECT-TYPE | |||
| SwBlmPerfEEMntEntry | |||
| swBlmPerfEEPort | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.1 | ||
| This object identifies the port number of the switch. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swBlmPerfEERefKey | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.2 | ||
| This object identifies the reference number of the counter. This reference is number assigned when a filter is created. In SNMP Index start one instead of 0, add one to actual ref key | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| swBlmPerfEECRC | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.3 | ||
| Get End to End CRC error for the frames that matched the SID-DID pair. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swBlmPerfEEFCWRx | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.4 | ||
| Get End to End count of Fibre Channel words (FCW), received by the port, that matched the SID-DID pair. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swBlmPerfEEFCWTx | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.5 | ||
| Get End to End count of Fibre Channel words (FCW), transmitted by the port, that matched the SID-DID pair. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swBlmPerfEESid | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.6 | ||
| Gets SID info by reference number. SID (Source Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N-Port from which the frame was sent. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swBlmPerfEEDid | 1.3.6.1.4.1.1588.2.1.1.1.23.2.1.7 | ||
| Gets DID info by reference number. DID (Destination Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N-Port to which the frame was sent. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swBlmPerfFltMntTable | 1.3.6.1.4.1.1588.2.1.1.1.23.3 | ||
| Filter based monitoring counter. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwBlmPerfFltMntEntry | |||
| swBlmPerfFltMntEntry | 1.3.6.1.4.1.1588.2.1.1.1.23.3.1 | ||
| Filter base monitoring counter for given port. | |||
| OBJECT-TYPE | |||
| SwBlmPerfFltMntEntry | |||
| swBlmPerfFltPort | 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.1 | ||
| This object identifies the port number of the switch. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swBlmPerfFltRefkey | 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.2 | ||
| This object identifies the reference number of the filter. This reference number is assigned when a filter is created. In SNMP Index start one instead of 0, add one to actual ref key | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| swBlmPerfFltCnt | 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.3 | ||
| Get statistics of filter based monitor. Filter based monitoring provides information about a filter hit count such as 1. Read command 2. SCSI or IP traffic 3. SCSI Read/Write | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swBlmPerfFltAlias | 1.3.6.1.4.1.1588.2.1.1.1.23.3.1.4 | ||
| Alias name for the filter. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..20) | ||
| swTrunk | 1.3.6.1.4.1.1588.2.1.1.1.24 | ||
| The OID sub-tree for swTrunk group. | |||
| OBJECT-IDENTITY | |||
| swSwitchTrunkable | 1.3.6.1.4.1.1588.2.1.1.1.24.1 | ||
| The trunking status of the switch - whether the switch supports the trunking feature or not. The values are yes(8) - the trunking feature is supported no(0). - the trunking feature is not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(8), no(0) | ||
| swTrunkTable | 1.3.6.1.4.1.1588.2.1.1.1.24.2 | ||
| Table to display trunking information for the switch. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwTrunkEntry | |||
| swTrunkEntry | 1.3.6.1.4.1.1588.2.1.1.1.24.2.1 | ||
| Entry for the trunking table. | |||
| OBJECT-TYPE | |||
| SwTrunkEntry | |||
| swTrunkPortIndex | 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.1 | ||
| This object identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. e.g. port index 1 correspond to port number 0. | |||
| OBJECT-TYPE | |||
| SwPortIndex | |||
| swTrunkGroupNumber | 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.2 | ||
| This object is a logical entity which specifies the Group Number to which the port belongs to. If this value is Zero it means the port is not Trunked. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swTrunkMaster | 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.3 | ||
| Port number that is the trunk master of the group. The trunk master implicitly defines the group. All ports with the same master are considered to be part of the same group. | |||
| OBJECT-TYPE | |||
| SwTrunkMaster | |||
| swPortTrunked | 1.3.6.1.4.1.1588.2.1.1.1.24.2.1.4 | ||
| The active trunk status for a member port. Values are enabled(1) or disabled(0). | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(0), enabled(1) | ||
| swTrunkGrpTable | 1.3.6.1.4.1.1588.2.1.1.1.24.3 | ||
| Table to display trunking Performance information for the switch. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwTrunkGrpEntry | |||
| swTrunkGrpEntry | 1.3.6.1.4.1.1588.2.1.1.1.24.3.1 | ||
| Entry for the trunking Group table. | |||
| OBJECT-TYPE | |||
| SwTrunkGrpEntry | |||
| swTrunkGrpNumber | 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.1 | ||
| This object is a logical entity which specifies the Group Number to which port belongs to. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| swTrunkGrpMaster | 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.2 | ||
| This object gives the master port id for the TrunkGroup. | |||
| OBJECT-TYPE | |||
| SwTrunkMaster | |||
| swTrunkGrpTx | 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.3 | ||
| Gives the aggregate value of the transmitted words from this TrunkGroup. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| swTrunkGrpRx | 1.3.6.1.4.1.1588.2.1.1.1.24.3.1.4 | ||
| Gives the aggregate value of the received words by this TrunkGroup. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| sw28k | 1.3.6.1.4.1.1588.2.1.1.2 | ||
| The OID for Brocade's Silkworm 2800 model Fibre Channel Switch. | |||
| OBJECT-IDENTITY | |||
| sw21kN24k | 1.3.6.1.4.1.1588.2.1.1.3 | ||
| The OID for Brocade's Silkworm 2100 and 2400 series model Fibre Channel Switch. | |||
| OBJECT-IDENTITY | |||
| sw20x0 | 1.3.6.1.4.1.1588.2.1.1.4 | ||
| The OID for Brocade's Silkworm 20x0 series model Fibre Channel Switch. | |||
| OBJECT-IDENTITY | |||
| swMibModule | 1.3.6.1.4.1.1588.3.1.3 | ||
| The MIB module is for Brocade's Fibre Channel Switch. Copyright (c) 1996-2003 Brocade Communications Systems, Inc. All rights reserved. | |||
| MODULE-IDENTITY | |||
| SwSevType | |||
| The event trap level in conjunction with the an event's severity level. | |||
| TEXTUAL-CONVENTION | |||
| INTEGER | none(0), critical(1), error(2), warning(3), informational(4), debug(5) | ||
| FcPortFlag | |||
| Represents the port status for a FC Flag. Currently this will indicate if the port is virtual or physical. | |||
| TEXTUAL-CONVENTION | |||
| BITS | virtual(0) | ||
| SwSensorEntry | |||
| SEQUENCE | |||
| SwSensorIndex as swSensorIndex | |||
| INTEGER as swSensorType | |||
| INTEGER as swSensorStatus | |||
| Integer32 as swSensorValue | |||
| DisplayString as swSensorInfo | SIZE(0..255) | ||
| SwNbEntry | |||
| SEQUENCE | |||
| SwNbIndex as swNbIndex | |||
| SwPortIndex as swNbMyPort | |||
| SwDomainIndex as swNbRemDomain | |||
| SwPortIndex as swNbRemPort | |||
| INTEGER as swNbBaudRate | |||
| INTEGER as swNbIslState | |||
| Integer32 as swNbIslCost | 0..2147483647 | ||
| OCTET STRING as swNbRemPortName | SIZE(8) | ||
| SwFabricMemEntry | |||
| SEQUENCE | |||
| FcWwn as swFabricMemWwn | |||
| SwDomainIndex as swFabricMemDid | |||
| DisplayString as swFabricMemName | SIZE(0..255) | ||
| IpAddress as swFabricMemEIP | |||
| IpAddress as swFabricMemFCIP | |||
| IpAddress as swFabricMemGWIP | |||
| Integer32 as swFabricMemType | 0..2147483647 | ||
| OCTET STRING as swFabricMemShortVersion | SIZE(0..24) | ||
| SwAgtCmtyEntry | |||
| SEQUENCE | |||
| Integer32 as swAgtCmtyIdx | 1..6 | ||
| DisplayString as swAgtCmtyStr | SIZE(2..16) | ||
| IpAddress as swAgtTrapRcp | |||
| SwSevType as swAgtTrapSeverityLevel | |||
| SwFCPortEntry | |||
| SEQUENCE | |||
| SwPortIndex as swFCPortIndex | |||
| INTEGER as swFCPortType | |||
| INTEGER as swFCPortPhyState | |||
| INTEGER as swFCPortOpStatus | |||
| INTEGER as swFCPortAdmStatus | |||
| INTEGER as swFCPortLinkState | |||
| INTEGER as swFCPortTxType | |||
| Counter32 as swFCPortTxWords | |||
| Counter32 as swFCPortRxWords | |||
| Counter32 as swFCPortTxFrames | |||
| Counter32 as swFCPortRxFrames | |||
| Counter32 as swFCPortRxC2Frames | |||
| Counter32 as swFCPortRxC3Frames | |||
| Counter32 as swFCPortRxLCs | |||
| Counter32 as swFCPortRxMcasts | |||
| Counter32 as swFCPortTooManyRdys | |||
| Counter32 as swFCPortNoTxCredits | |||
| Counter32 as swFCPortRxEncInFrs | |||
| Counter32 as swFCPortRxCrcs | |||
| Counter32 as swFCPortRxTruncs | |||
| Counter32 as swFCPortRxTooLongs | |||
| Counter32 as swFCPortRxBadEofs | |||
| Counter32 as swFCPortRxEncOutFrs | |||
| Counter32 as swFCPortRxBadOs | |||
| Counter32 as swFCPortC3Discards | |||
| Counter32 as swFCPortMcastTimedOuts | |||
| Counter32 as swFCPortTxMcasts | |||
| Counter32 as swFCPortLipIns | |||
| Counter32 as swFCPortLipOuts | |||
| OCTET STRING as swFCPortLipLastAlpa | SIZE(4) | ||
| OCTET STRING as swFCPortWwn | |||
| INTEGER as swFCPortSpeed | |||
| DisplayString as swFCPortName | SIZE(0..32) | ||
| DisplayString as swFCPortSpecifier | |||
| FcPortFlag as swFCPortFlag | |||
| INTEGER as swFCPortBrcdType | |||
| SwNsEntry | |||
| SEQUENCE | |||
| Integer32 as swNsEntryIndex | 0..2147483647 | ||
| OCTET STRING as swNsPortID | SIZE(4) | ||
| INTEGER as swNsPortType | |||
| FcWwn as swNsPortName | |||
| OCTET STRING as swNsPortSymb | |||
| FcWwn as swNsNodeName | |||
| OCTET STRING as swNsNodeSymb | |||
| OCTET STRING as swNsIPA | |||
| OCTET STRING as swNsIpAddress | |||
| INTEGER as swNsCos | |||
| OCTET STRING as swNsFc4 | |||
| OCTET STRING as swNsIpNxPort | SIZE(16) | ||
| OCTET STRING as swNsWwn | SIZE(8) | ||
| OCTET STRING as swNsHardAddr | SIZE(3) | ||
| SwEventEntry | |||
| SEQUENCE | |||
| Integer32 as swEventIndex | 0..2147483647 | ||
| DisplayString as swEventTimeInfo | SIZE(0..64) | ||
| INTEGER as swEventLevel | |||
| Integer32 as swEventRepeatCount | 0..2147483647 | ||
| DisplayString as swEventDescr | |||
| SwFwActs | |||
| INTEGER | swFwNoAction(0), swFwErrlog(1), swFwSnmptrap(2), swFwErrlogSnmptrap(3), swFwPortloglock(4), swFwErrlogPortloglock(5), swFwSnmptrapPortloglock(6), swFwErrlogSnmptrapPortloglock(7), swFwRn(8), swFwElRn(9), swFwStRn(10), swFwElStRn(11), swFwPlRn(12), swFwElPlRn(13), swFwStPlRn(14), swFwElStPlRn(15), swFwMailAlert(16), swFwMailAlertErrlog(17), swFwMailAlertSnmptrap(18), swFwMailAlertErrlogSnmptrap(19), swFwMailAlertPortloglock(20), swFwMailAlertErrlogPortloglock(21), swFwMailAlertSnmptrapPortloglock(22), swFwMailAlertErrlogSnmptrapPortloglock(23), swFwMailAlertRn(24), swFwElMailAlertRn(25), swFwMailAlertStRn(26), swFwMailAlertElStRn(27), swFwMailAlertPlRn(28), swFwMailAlertElPlRn(29), swFwMailAlertStPlRn(30), swFwMailAlertElStPlRn(31) | ||
| SwFwLevels | |||
| INTEGER | swFwReserved(1), swFwDefault(2), swFwCustom(3) | ||
| SwFwClassesAreas | |||
| INTEGER | swFwEnvTemp(1), swFwEnvFan(2), swFwEnvPs(3), swFwTransceiverTemp(4), swFwTransceiverRxp(5), swFwTransceiverTxp(6), swFwTransceiverCurrent(7), swFwPortLink(8), swFwPortSync(9), swFwPortSignal(10), swFwPortPe(11), swFwPortWords(12), swFwPortCrcs(13), swFwPortRXPerf(14), swFwPortTXPerf(15), swFwPortState(16), swFwFabricEd(17), swFwFabricFr(18), swFwFabricDi(19), swFwFabricSc(20), swFwFabricZc(21), swFwFabricFq(22), swFwFabricFl(23), swFwFabricGs(24), swFwEPortLink(25), swFwEPortSync(26), swFwEPortSignal(27), swFwEPortPe(28), swFwEPortWords(29), swFwEPortCrcs(30), swFwEPortRXPerf(31), swFwEPortTXPerf(32), swFwEPortState(33), swFwFCUPortLink(34), swFwFCUPortSync(35), swFwFCUPortSignal(36), swFwFCUPortPe(37), swFwFCUPortWords(38), swFwFCUPortCrcs(39), swFwFCUPortRXPerf(40), swFwFCUPortTXPerf(41), swFwFCUPortState(42), swFwFOPPortLink(43), swFwFOPPortSync(44), swFwFOPPortSignal(45), swFwFOPPortPe(46), swFwFOPPortWords(47), swFwFOPPortCrcs(48), swFwFOPPortRXPerf(49), swFwFOPPortTXPerf(50), swFwFOPPortState(51), swFwPerfALPACRC(52), swFwPerfEToECRC(53), swFwPerfEToERxCnt(54), swFwPerfEToETxCnt(55), swFwPerffltCusDef(56), swFwTransceiverVoltage(57), swFwSecTelnetViolations(58), swFwSecHTTPViolations(59), swFwSecAPIViolations(60), swFwSecRSNMPViolations(61), swFwSecWSNMPViolations(62), swFwSecSESViolations(63), swFwSecMSViolations(64), swFwSecSerialViolations(65), swFwSecFPViolations(66), swFwSecSCCViolations(67), swFwSecDCCViolations(68), swFwSecLoginViolations(69), swFwSecInvaledTS(70), swFwSecInvalidSign(71), swFwSecInvalidCert(72), swFwSecSlapFail(73), swFwSecSlapBadPkt(74), swFwSecTSOutSync(75), swFwSecNoFcs(76), swFwSecIncompDB(77), swFwSecIllegalCmd(78), swFwSAMTotalDownTime(79), swFwSAMTotalUpTime(80), swFwSAMDurationOfOccur(81), swFwSAMFreqOfOccur(82), swFwResourceFlash(83), swFwEPortUtil(84), swFwEPortPktl(85) | ||
| SwFwWriteVals | |||
| INTEGER | swFwCancelWrite(1), swFwApplyWrite(2) | ||
| SwFwTimebase | |||
| INTEGER | swFwTbNone(1), swFwTbSec(2), swFwTbMin(3), swFwTbHour(4), swFwTbDay(5) | ||
| SwFwStatus | |||
| INTEGER | disabled(1), enabled(2) | ||
| SwFwEvent | |||
| INTEGER | started(1), changed(2), exceeded(3), below(4), above(5), inBetween(6) | ||
| SwFwBehavior | |||
| INTEGER | triggered(1), continuous(2) | ||
| SwFwState | |||
| INTEGER | swFwInformative(1), swFwNormal(2), swFwFaulty(3) | ||
| SwFwLicense | |||
| INTEGER | swFwLicensed(1), swFwNotLicensed(2) | ||
| SwFwClassAreaEntry | |||
| SEQUENCE | |||
| SwFwClassesAreas as swFwClassAreaIndex | |||
| SwFwWriteVals as swFwWriteThVals | |||
| DisplayString as swFwDefaultUnit | |||
| SwFwTimebase as swFwDefaultTimebase | |||
| Integer32 as swFwDefaultLow | 0..2147483647 | ||
| Integer32 as swFwDefaultHigh | 0..2147483647 | ||
| Integer32 as swFwDefaultBufSize | 0..2147483647 | ||
| DisplayString as swFwCustUnit | |||
| SwFwTimebase as swFwCustTimebase | |||
| Integer32 as swFwCustLow | 0..2147483647 | ||
| Integer32 as swFwCustHigh | 0..2147483647 | ||
| Integer32 as swFwCustBufSize | 0..2147483647 | ||
| SwFwLevels as swFwThLevel | |||
| SwFwWriteVals as swFwWriteActVals | |||
| SwFwActs as swFwDefaultChangedActs | |||
| SwFwActs as swFwDefaultExceededActs | |||
| SwFwActs as swFwDefaultBelowActs | |||
| SwFwActs as swFwDefaultAboveActs | |||
| SwFwActs as swFwDefaultInBetweenActs | |||
| SwFwActs as swFwCustChangedActs | |||
| SwFwActs as swFwCustExceededActs | |||
| SwFwActs as swFwCustBelowActs | |||
| SwFwActs as swFwCustAboveActs | |||
| SwFwActs as swFwCustInBetweenActs | |||
| SwFwActs as swFwValidActs | |||
| SwFwLevels as swFwActLevel | |||
| SwFwThresholdEntry | |||
| SEQUENCE | |||
| Integer32 as swFwThresholdIndex | 0..2147483647 | ||
| SwFwStatus as swFwStatus | |||
| DisplayString as swFwName | SIZE(0..32) | ||
| DisplayString as swFwLabel | SIZE(0..70) | ||
| Integer32 as swFwCurVal | 0..2147483647 | ||
| SwFwEvent as swFwLastEvent | |||
| Integer32 as swFwLastEventVal | 0..2147483647 | ||
| DisplayString as swFwLastEventTime | SIZE(0..32) | ||
| SwFwState as swFwLastState | |||
| SwFwBehavior as swFwBehaviorType | |||
| Integer32 as swFwBehaviorInt | 0..2147483647 | ||
| SwSevType as swFwLastSeverityLevel | |||
| SwEndDeviceRlsEntry | |||
| SEQUENCE | |||
| Integer32 as swEndDevicePort | 0..2147483647 | ||
| Integer32 as swEndDeviceAlpa | 0..2147483647 | ||
| OCTET STRING as swEndDevicePortID | SIZE(4) | ||
| Integer32 as swEndDeviceLinkFailure | 0..2147483647 | ||
| Integer32 as swEndDeviceSyncLoss | 0..2147483647 | ||
| Integer32 as swEndDeviceSigLoss | 0..2147483647 | ||
| Integer32 as swEndDeviceProtoErr | 0..2147483647 | ||
| Integer32 as swEndDeviceInvalidWord | 0..2147483647 | ||
| Integer32 as swEndDeviceInvalidCRC | 0..2147483647 | ||
| SwGroupEntry | |||
| SEQUENCE | |||
| Integer32 as swGroupIndex | 0..2147483647 | ||
| OCTET STRING as swGroupName | SIZE(0..32) | ||
| OCTET STRING as swGroupType | SIZE(0..15) | ||
| SwGroupMemEntry | |||
| SEQUENCE | |||
| Integer32 as swGroupId | 0..2147483647 | ||
| FcWwn as swGroupMemWwn | |||
| Integer32 as swGroupMemPos | 0..2147483647 | ||
| SwBlmPerfALPAMntEntry | |||
| SEQUENCE | |||
| SwPortIndex as swBlmPerfAlpaPort | |||
| Integer32 as swBlmPerfAlpaIndx | 1..126 | ||
| Integer32 as swBlmPerfAlpa | 0..2147483647 | ||
| OCTET STRING as swBlmPerfAlpaCRCCnt | |||
| SwBlmPerfEEMntEntry | |||
| SEQUENCE | |||
| SwPortIndex as swBlmPerfEEPort | |||
| Integer32 as swBlmPerfEERefKey | 1..8 | ||
| OCTET STRING as swBlmPerfEECRC | |||
| OCTET STRING as swBlmPerfEEFCWRx | |||
| OCTET STRING as swBlmPerfEEFCWTx | |||
| Integer32 as swBlmPerfEESid | 0..2147483647 | ||
| Integer32 as swBlmPerfEEDid | 0..2147483647 | ||
| SwBlmPerfFltMntEntry | |||
| SEQUENCE | |||
| SwPortIndex as swBlmPerfFltPort | |||
| Integer32 as swBlmPerfFltRefkey | 1..8 | ||
| OCTET STRING as swBlmPerfFltCnt | |||
| DisplayString as swBlmPerfFltAlias | SIZE(0..20) | ||
| SwTrunkEntry | |||
| SEQUENCE | |||
| SwPortIndex as swTrunkPortIndex | |||
| Integer32 as swTrunkGroupNumber | 0..2147483647 | ||
| SwTrunkMaster as swTrunkMaster | |||
| INTEGER as swPortTrunked | |||
| SwTrunkGrpEntry | |||
| SEQUENCE | |||
| Integer32 as swTrunkGrpNumber | 0..2147483647 | ||
| SwTrunkMaster as swTrunkGrpMaster | |||
| OCTET STRING as swTrunkGrpTx | SIZE(8) | ||
| OCTET STRING as swTrunkGrpRx | SIZE(8) | ||