
| SNMPv2-SMI | SNMPv2-TC | ID-REC-MIB |
| DLINKMGMT-MIB | RFC1213-MIB |
| Counter32 | Counter64 | TimeTicks |
| NOTIFICATION-TYPE | MODULE-IDENTITY | OBJECT-TYPE |
| IpAddress | Unsigned32 | MacAddress |
| RowStatus | dlink | dlinkMgmtMIB |
| DisplayString |
| dlink-products | 1.3.6.1.4.1.326.2.20.1.10 | ||
| OBJECT IDENTIFIER | |||
| dlink-Des3326Prod | 1.3.6.1.4.1.326.2.20.1.10.32 | ||
| OBJECT IDENTIFIER | |||
| swProperty | 1.3.6.1.4.1.326.2.20.1.10.32.1 | ||
| OBJECT IDENTIFIER | |||
| swModule | 1.3.6.1.4.1.326.2.20.1.10.32.1.1 | ||
| OBJECT IDENTIFIER | |||
| des3326Series | 1.3.6.1.4.1.326.2.20.1.11.32 | ||
| OBJECT IDENTIFIER | |||
| swL2MgmtMIB | 1.3.6.1.4.1.326.2.20.1.11.32.2 | ||
| The Structure of Layer 2 Network Management Information for the D-Link enterprise. | |||
| MODULE-IDENTITY | |||
| swL2DevMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.1 | ||
| OBJECT IDENTIFIER | |||
| swL2DevInfo | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1 | ||
| OBJECT IDENTIFIER | |||
| swDevInfoSystemUpTime | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.1 | ||
| The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in units of seconds. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| swDevInfoTotalNumOfPort | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.2 | ||
| The number of ports within this switch. This value is the sum of the ports within this switch. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swDevInfoNumOfPortInUse | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.3 | ||
| The number of ports in this switch connected to the segment or the end stations. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swDevInfoConsoleInUse | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.4 | ||
| This usage indication of console system. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), in-use(2), not-in-use(3) | ||
| swDevInfoFrontPanelLedStatus | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.5 | ||
| This object is a set of system LED indications. The first third octets is defined as system LED . The first LED is power LED . The second LED is console LED . The third LED is RPS (Redundancy Power Supply) LED . . The other octets following the third octets are the logical port LED (following dot1dBasePort ordering) . Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED . The second byte is presented to the Speed LED . There is one byte per LED . The most significant bit is used for blink/solid: Off = The LED is lit permanently. On = The LED blinks. The three least significant bits are used for color: 1 = not lit, 2 = green, 3 = yellow,(orange) 4 = blue, 5 = red, 0+6+7 not used The four remaining bits are currently unused and must be 0 . | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..127) | ||
| swL2DevCtrlUpDownloadState | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.6 | ||
| status of upload/download control. If the value is 'other', means never firmware updated since device started up. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8) | ||
| swL2DevCtrlUpDownloadTime | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.7 | ||
| record the sysUptime for last active swL2DevCtrlUpDownloadImage. Default is set to 0. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| swDevInfoSaveCfg | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.1.8 | ||
| This object indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is saving into NV-RAM. completed(3) - all of the device configuration parameters have been saved into NV-RAM. changed-not-save(4) - some of the device configuration parameters have been changed but not saved into NV-RAM. failed(5) - The processing of saving the device configuration has failed. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), proceeding(2), completed(3), changed-not-save(4), failed(5) | ||
| swL2DevCtrl | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2 | ||
| OBJECT IDENTIFIER | |||
| swL2DevCtrlStpState | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.1 | ||
| This object can be enabled or disabled spanning tree algorithm during runtime of the system. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevCtrlIGMPSnooping | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.2 | ||
| This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevCtrlBcastStromCtrl | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.3 | ||
| This object indicates broadcast storm control function is enabled or disabled. The swL2PortCtrlBMStromPercentage object will descript the detail about the storm control . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevCtrlMcastStromCtrl | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.4 | ||
| This object indicates multicast storm control function is enabled or disabled. The swL2PortCtrlBMStromPercentage object will descript the detail about the storm control . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevCtrlProtoCapability | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.5 | ||
| This object control which protocol capability will be enable (or disable) when the switch hub restart at the startup (power on) or warm start . To change the value will immediately restart the device . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), layer2-default(2), layer2-ieee8021q(3), layer3-ip-ipx-default-routing(4), layer3-ip-ipx-ieee8021q-routing(5) | ||
| swL2DevCtrlUpDownloadImageFileName | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.6 | ||
| The name of the image file to be uploaded/Downloaded from the device to TFTP server when enabling image upload/download function (by writing swL2DevCtrlUpDownloadImage). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swL2DevCtrlUpDownloadImageSourceAddr | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.7 | ||
| The ip address where been uploaded/Downloaded image file. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swL2DevCtrlUpDownloadImage | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.8 | ||
| Image file upload/download control. After setting, it will immediately invoke image upload/download function. While retrieving the value of this object, it always returns 'other' normally. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), upload(2), download(3) | ||
| swL2DevCtrlSaveCfg | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.9 | ||
| As the object is set to active, the current device configuration is save into to NV-RAM.If set to normal, do nothing. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), active(2) | ||
| swL2DevCtrlCleanAllStatisticCounter | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.2.10 | ||
| As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), active(2) | ||
| swL2DevAlarm | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.3 | ||
| OBJECT IDENTIFIER | |||
| swL2DevAlarmNewRoot | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.3.1 | ||
| When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevAlarmTopologyChange | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.3.2 | ||
| This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2DevAlarmLinkChange | 1.3.6.1.4.1.326.2.20.1.11.32.2.1.3.3 | ||
| This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2UnitMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.2 | ||
| OBJECT IDENTIFIER | |||
| swL2UnitCtrl | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1 | ||
| OBJECT IDENTIFIER | |||
| swL2UnitCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1.1 | ||
| A table that contains control information about every unit. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2UnitCtrlEntry | |||
| swL2UnitCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1.1.1 | ||
| A list of control information for each unit of the device. | |||
| OBJECT-TYPE | |||
| SwL2UnitCtrlEntry | |||
| swL2UnitCtrlUnitIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1.1.1.1 | ||
| This object indicates the unit number .(1..Max unit number) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2UnitCtrlSwFileName | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1.1.1.2 | ||
| The name of the firmware file to be downloaded from the TFTP server to the unit when enabling image upload function (by writing swL2UnitCtrlSwUpdateCtrl object). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swL2UnitCtrlSwUpdateCtrl | 1.3.6.1.4.1.326.2.20.1.11.32.2.2.1.1.1.3 | ||
| Image file download control. As the object is set to active, it will immediately invoke firmware download function, and if set to normal, do nothing. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), active(2) | ||
| swL2ModuleMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.3 | ||
| OBJECT IDENTIFIER | |||
| swL2PortMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.4 | ||
| OBJECT IDENTIFIER | |||
| swL2PortInfoTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1 | ||
| A table that contains information about every port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2PortInfoEntry | |||
| swL2PortInfoEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1 | ||
| A list of information for each port of the device. | |||
| OBJECT-TYPE | |||
| SwL2PortInfoEntry | |||
| swL2PortInfoUnitIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.1 | ||
| Indicates ID of the unit in the device | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortInfoModuleIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.2 | ||
| Indicates ID of the module on the unit .(1..Max module number in the unit) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortInfoPortIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.3 | ||
| This object indicates the module's port number.(1..Max port number in the module) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortInfoType | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.4 | ||
| This object indicates the connector type of this port. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), portType-UTP(2), portType-AUI(3), portType-Fiber-MTRJ(4), portType-Fiber-SC(5), portType-Fiber-GBIC(6), portType-BNC(7) | ||
| swL2PortInfoDescr | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.5 | ||
| Provides port type information in displayed string format | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| swL2PortInfoLinkStatus | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.6 | ||
| This object indicates the port link status. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), link-pass(2), link-fail(3) | ||
| swL2PortInfoNwayStatus | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.1.1.7 | ||
| This object indicates the port speed and duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5), half-1Gigabps(6), full-1Gigabps(7) | ||
| swL2PortCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2 | ||
| A table that contains control information about every port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2PortCtrlEntry | |||
| swL2PortCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1 | ||
| A list of control information for each port of the device. | |||
| OBJECT-TYPE | |||
| SwL2PortCtrlEntry | |||
| swL2PortCtrlUnitIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.1 | ||
| Indicates ID of the unit in the device | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortCtrlModuleIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.2 | ||
| Indicates ID of the module on the unit.(1..Max module number in the unit) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortCtrlPortIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.3 | ||
| This object indicates the module's port number.(1..Max port number in the module) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortCtrlAdminState | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.4 | ||
| This object decide the port enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2PortCtrlNwayState | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.5 | ||
| Chose the port speed, duplex mode, and N-Way function mode. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8) | ||
| swL2PortCtrlFlowCtrlState | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.6 | ||
| Set IEEE 802.3x compliant flow control function as enabled or disabled. And IEEE 802.3x compliant flow control function work only when the port is in full duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2PortCtrlBackPressState | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.7 | ||
| Depending on this object determine to enable or disable the backpressure function when the port is working in half duplex mode. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2PortCtrlBMStromPercentage | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.2.1.8 | ||
| This object to decide how much percentage broadcast/multicast (depend on swL2DevCtrlBcastStromCtrl or swL2DevCtrlMcastStromCtrl objects whether is enabled) will active storm control . Whenever a port reaches its configured percentage amount of packets in the one second time interval , the device will start dropping that type of packet , until the time interval has expired . Once the time interval has expired , the device will start forwarding that type of packet . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..100 | ||
| swL2PortTxPrioQueueCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3 | ||
| A table that contains transmit queue priority control information about every port. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2PortTxPrioQueueCtrlEntry | |||
| swL2PortTxPrioQueueCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1 | ||
| A list of transmit queue priority control information for each port of the device. | |||
| OBJECT-TYPE | |||
| SwL2PortTxPrioQueueCtrlEntry | |||
| swL2PortTxPrioQueueUnitIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.1 | ||
| Indicates ID of the unit in the device | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortTxPrioQueueModuleIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.2 | ||
| Indicates ID of the module on the unit.(1..Max module number in the unit) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swPortTxPrioQueueCtrlPortIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.3 | ||
| This object indicates the module's port number.(1..Max port number in the module) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortTxPrioQueuePrioAlgorithm | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.4 | ||
| This object decide the weighted fair queueing algorithm for the bandwidth management . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. credit(2) - In the credit algorithm, each queue is assigned a certain percent of the total bandwidth for a given port . In the mode , each priority queue is granted access to transmit in a round-robin fashion . If queue 0 to 3 have weight 10% ,20% ,30% and 40% . For example , if only queue 0 and 1 have packets waiting for transmitting , the queue 0 will get 33.33% bandwidth and queue 1 will get 66.67% bandwidth . strict(3) - The strict priority algorithm always grants requests in a fixed priority , with queue 3 having the highest priority , and queue 0 having the lowest . While higher priority queues have packets to send , lower priority queues will not be granted . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), credit(2), strict(3) | ||
| swL2PortTxPrioQueueQ0Weight | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.5 | ||
| The weight value of the transmit priority queue 0 . The all queues sum value must be equal 100 . The value must be smallest than other queues . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortTxPrioQueueQ1Weight | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.6 | ||
| The weight value of the transmit priority queue 1 . The all queues sum value must be equal 100 . The value must be bigger than queue 0 . And the value must be smallest than queue 2 and queue 3 . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortTxPrioQueueQ2Weight | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.7 | ||
| The weight value of the transmit priority queue 2 . The all queues sum value must be equal 100 . The value must be biggest than queue 0 and queue 1 . And the value must be smaller than queue 3 . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortTxPrioQueueQ3Weight | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.3.1.8 | ||
| The weight value of the transmit priority queue 3 . The all queues sum value must be equal 100 . The value must be biggest than other queues . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortStTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4 | ||
| A list of port statistic Counter entries. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2PortStEntry | |||
| swL2PortStEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1 | ||
| This entry include all the port statistic Counter which support by the device, like Bytes received, Bytes Sent ... | |||
| OBJECT-TYPE | |||
| SwL2PortStEntry | |||
| swL2PortStUnitIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.1 | ||
| This object indicates ID of the unit in the device | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortStModuleIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.2 | ||
| This object indicates ID of the module on the unit.(1..Max module number in the unit) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortStPortlndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.3 | ||
| This object indicates the module's port number.(1..Max port number in the module) | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PortStRxBytes | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.4 | ||
| This counter is incremented once for every data octet of good packets received . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.5 | ||
| This counter is incremented once for every received good packet . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxCRCErrorPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.6 | ||
| This counter is incremented once for every received packet which has invalid CRC . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxVlanDetected | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.7 | ||
| This counter is incremented once for every received packet which has differ Vlan ID . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxMcastPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.8 | ||
| This counter is incremented once for every received packet which has multicast destination MAC address . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxBcastPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.9 | ||
| This counter is incremented once for every received packet which has broadcast destination MAC address (0xFFFFFFFFFFFF). | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxUndersizePkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.10 | ||
| This counter is incremented once for every received packet which meets any one the following conditions: 1.Receive byte count < 64 bytes and not CRC error . 2.Receive byte count < 68 bytes and tag packet and not CRC error . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxOversizePkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.11 | ||
| This counter is incremented once for every received packet which meets any one the following conditions: 1.Receive byte count >1518 . 2.Receive byte count > 1522 and tag packet . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxFragmentsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.12 | ||
| This counter is incremented once for every received packet which meets any one the following conditions: 1.Receive byte count < 64 bytes and CRC error . 2.Receive byte count < 68 bytes and tag packet and CRC error . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxJabbersPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.13 | ||
| This counter is incremented once for every received packet which meets any one the following conditions: 1.Receive byte count > 1518 and CRC error . 2.Receive byte count > 1522 bytes and tag packet and CRC error . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx64OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.14 | ||
| This counter is incremented once for every received packet with size of 64 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx65To127OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.15 | ||
| This counter is incremented once for every received packet with size of 65 to 127 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx128To255OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.16 | ||
| This counter is incremented once for every received packet with size of 128 to 255 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx256To511OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.17 | ||
| This counter is incremented once for every received packet with size of 256 to 511 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx512To1023OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.18 | ||
| This counter is incremented once for every received packet with size of 512 to 1023 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRx1024To1518OctsPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.19 | ||
| This counter is incremented once for every received packet with size of 1024 to 1536 bytes . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxBytes | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.20 | ||
| This counter is incremented once for every data octet of a trans- mitted good packet . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxTotalBytes | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.21 | ||
| This counter is incremented once for every data octet of a trans- mitted packet . This counter includes rejected transmitted packets . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.22 | ||
| This counter is incremented once for every transmitted good packet. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxExDeferPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.23 | ||
| This counter is incremented once for every transmitted packet which excessive defer . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxGiantPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.24 | ||
| This counter is incremented once for every transmitted packet which transmit giant . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxUnderRunPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.25 | ||
| This counter is incremented once for every transmitted packet which transmit under run . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxCRCErrorPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.26 | ||
| This counter is incremented once for every transmitted packet which has invalid CRC . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxLenCheckErrorPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.27 | ||
| This counter is incremented once for every transmitted packet which has error length . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxLenOutRangePkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.28 | ||
| This counter is incremented once for every transmitted packet which has length out of range . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxLateCollPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.29 | ||
| This counter is incremented once for every transmitted packet which has transmit late collision . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxExCollPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.30 | ||
| This counter is incremented once for every transmitted packet which has transmit excessive collision . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxSingleCollPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.31 | ||
| This counter is incremented once for every transmitted packet which has transmit collision count = 1 . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStTxCollPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.32 | ||
| This counter is incremented once for every transmitted packet which has transmit collision . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxDropPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.33 | ||
| This counter is incremented once for every received packet which has dropped for any reason . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStRxLocalDropPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.34 | ||
| This counter is incremented once for every received packet which local has dropped for any reason . | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| swL2PortStHCRxBytes | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.35 | ||
| This high capacbility (64 bit) counter is incremented once for every data octet of good packets received . | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| swL2PortStHCRxPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.36 | ||
| This high capability (64 bit) counter is incremented once for every received good packet. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| swL2PortStHCTxBytes | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.37 | ||
| This high capability (64 bit) counter is incremented once for every data octet of a transmitted good packet . | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| swL2PortStHCTxPkts | 1.3.6.1.4.1.326.2.20.1.11.32.2.4.4.1.38 | ||
| This high capability (64 bit) counter is incremented once for every transmitted good packet. | |||
| OBJECT-TYPE | |||
| Counter64 | |||
| swL2FdbMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.5 | ||
| OBJECT IDENTIFIER | |||
| swL2McastFdbStaticMaxSupportedEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.1 | ||
| Maximum number of entries in the static multicast forwarding table (swL2McastFdbStaticTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2McastFdbStaticCurrentTotalEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.2 | ||
| Current exist number of entries in the static multicast forwarding table . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2McastFdbStaticTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3 | ||
| This table defines for frames with specific multicast destination MAC address, the set of ports that the frame will be forwarded to . Note that the priority of FDB table entries is lower than Filtering Table , i.e. if there is a table hash collision between the entries of FDB Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of FDB Table . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2McastFdbStaticEntry | |||
| swL2McastFdbStaticEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1 | ||
| A list of information specifies which ports the frames with specific multicast destination MAC address to go. | |||
| OBJECT-TYPE | |||
| SwL2McastFdbStaticEntry | |||
| swL2McastFdbStaticAddress | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1.1 | ||
| The destination MAC address in a frame to which this entry's forwarding information applies . This object only can take the value of the multicast address . | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swL2McastFdbStaticPortMap | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1.2 | ||
| The set of ports to which frames received from a specific port and destined for a specific MAC address, are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) . The 4 octets is represent one unit port according its logic port . If the unit less 32 port , the other port don't care just fill zero . | |||
| OBJECT-TYPE | |||
| PortList | |||
| swL2McastFdbStaticJoinIGMP | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1.3 | ||
| This object indicates whether to allow ports to join/leave IGMP group via IGMP Snooping. For a multicast address entry, port group could be classified into two catelogies : one is static and another is dynamic. In static port group, port members is defined statically by user, and dynamic port group allows a port member to join/leave the membership dynamically, according to IGMP report/leave messages. When this object is set to 'enabled', it allows dynamic port group updated for the multicast address entry as well as static port group. When it is set to 'disabled' , dynamic port member join/leave is disabled, but static port group is not affected. This object is only vaild for multicast address indicated by swFdbStaticAddressIndex . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - this entry doesn't allow dynamic updates via IGMP Snooping.This is a default setting. enabled(3) - this entry allow dynamic updates via IGMP Snooping. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2McastFdbStaticState | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1.4 | ||
| This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), invalid(2), valid(3) | ||
| swL2McastFdbStaticstatus | 1.3.6.1.4.1.326.2.20.1.11.32.2.5.3.1.5 | ||
| This object indicates the status of this entry . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values . apply(2) - this entry is currently in use and reside in the table . not-apply(3) - this entry is reside in the table but currently not in use due to conflict with other table . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), apply(2), not-apply(3) | ||
| swL2FilterMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.6 | ||
| OBJECT IDENTIFIER | |||
| swL2FilterAddrConfig | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1 | ||
| OBJECT IDENTIFIER | |||
| swL2FilterAddrMaxSupportedEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.1 | ||
| Maximum number of entries in the MAC address filtering table (swL2FilterAddrCtrlTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2FilterAddrCurrentTotalEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.2 | ||
| Current applied number of entries in the MAC address filtering table . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2FilterAddrCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.3 | ||
| This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA) . The MAC address can be a unicast address or a multicast address .This table has higher priority than both static FDB table and IGMP table . It means that if a MAC address appears on this table also appears on the static FDB table , the device will use the information provide by this table to process the packet . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2FilterAddrCtrlEntry | |||
| swL2FilterAddrCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.3.1 | ||
| A list of information about a specific unicast/multicast MAC address for which the switch has filtering information . | |||
| OBJECT-TYPE | |||
| SwL2FilterAddrCtrlEntry | |||
| swL2FilterAddrVid | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.3.1.1 | ||
| This object indicates the VLAN-ID. If VLAN is in disabled mode, the object indicates the default VLAN-ID (0) . | |||
| OBJECT-TYPE | |||
| VlanIndex | |||
| swL2FilterAddrMacIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.3.1.2 | ||
| This object indicates a unicast/multicast MAC address for which the switch has filtering information . But if the swL2FilterAddrState = src-addr then the object can not be a multicast MAC address . | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swL2FilterAddrState | 1.3.6.1.4.1.326.2.20.1.11.32.2.6.1.3.1.3 | ||
| This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values . dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the MAC address entry of the table . src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the MAC address entry of the table . dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the MAC address entry of the table . invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4), invalid(5) | ||
| swL2TrunkMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.8 | ||
| OBJECT IDENTIFIER | |||
| swL2TrunkMaxSupportedEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.1 | ||
| Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2TrunkCurrentNumEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.2 | ||
| Current actived number of entries in the trunk configuration table . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2TrunkCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3 | ||
| This table specifys which ports group a set of ports(up to 8) into a single logical link. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2TrunkCtrlEntry | |||
| swL2TrunkCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1 | ||
| A list of information specifies which ports group a set of ports(up to 8) into a single logical link. | |||
| OBJECT-TYPE | |||
| SwL2TrunkCtrlEntry | |||
| swL2TrunkIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1.1 | ||
| The index of logical port trunk. The trunk group number depend on the existence of unit and module. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2TrunkName | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1.2 | ||
| The name of logical port trunk. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(12) | ||
| swL2TrunkMasterPortIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1.3 | ||
| The object indicates the master port number of the port trunk entry.The first port of the trunk is implicitly configured to be the master logical port.When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2TrunkMemberNum | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1.4 | ||
| Indicate how many number of ports is included in this Trunk . The trunk port number depend on the existence of module . The maximum number of ports is 8 for one trunks . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2TrunkState | 1.3.6.1.4.1.326.2.20.1.11.32.2.8.3.1.5 | ||
| This object decide the port trunk enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disabled(2), enabled(3) | ||
| swL2MirrorMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.9 | ||
| OBJECT IDENTIFIER | |||
| swL2MirrorLogicTargetPort | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.1 | ||
| This object indicates switch which port will sniff another port . A trunk port member cannot be configured as a target Snooping port . The port number is the sequential (logical) number which is also applied to bridge MIB, etc . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2MirrorPortConfig | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2 | ||
| OBJECT IDENTIFIER | |||
| swL2MirrorPortMaxSupportedEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.1 | ||
| Maximum number of entries in the port base mirror configuration table (swL2MirrorPortCtrlTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2MirrorPortCurrentNumEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.2 | ||
| Current applied number of entries in the port base mirror configuration table . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2MirrorPortCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.3 | ||
| A list of port snooping entries . Port snooping function provide an easy way to monitor traffic on any port . In this way any good packets appears on the source mirror port also shows up on the target mirror port and doesn't to reconstruct the LAN . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2MirrorPortCtrlEntry | |||
| swL2MirrorPortCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.3.1 | ||
| A list of information provide an easy way to monitor traffic on any port. The use can bring a fancy network monitor attaching to any target mirror port and set the port to be monitored as source mirror port . | |||
| OBJECT-TYPE | |||
| SwL2MirrorPortCtrlEntry | |||
| swL2MirrorPortLogicSourcePort | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.3.1.1 | ||
| This object indicates the number of port to be sniffed. The port number is the sequential (logical) number which is also applied to bridge MIB, etc. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2MirrorPortSourceDirection | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.3.1.2 | ||
| This object indicates the packet direction of the source port . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values . ingress(2) - the represent the ingress into the source port packet to sniffed . egress(3) - the represent the egress from the source port packet to sniffed . ingress-egress(4) - the represent the egress from or ingress into the source port packet to sniffed . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), ingress(2), egress(3), ingress-egress(4) | ||
| swL2MirrorPortState | 1.3.6.1.4.1.326.2.20.1.11.32.2.9.2.3.1.3 | ||
| This object indicates the port mirroring state . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values . disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table . enabled(3) - this entry is reside in the table . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disable(2), enable(3) | ||
| swL2IGMPMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.10 | ||
| OBJECT IDENTIFIER | |||
| swL2IGMPMaxSupportedVlans | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.1 | ||
| Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPMaxIpGroupNumPerVlan | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.2 | ||
| Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPLastQueryIPAddr | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.3 | ||
| This object indicates the ip address of last send IGMP query packet . | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swL2IGMPCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4 | ||
| The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2IGMPCtrlEntry | |||
| swL2IGMPCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4.1 | ||
| The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. | |||
| OBJECT-TYPE | |||
| SwL2IGMPCtrlEntry | |||
| swL2IGMPCtrlIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4.1.1 | ||
| This object indicates the IGMP control entry number.Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled , there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries is 12, with index range from 1 to 12. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..12 | ||
| swL2IGMPCtrlVid | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4.1.2 | ||
| This object indicates the IGMP control entry's VLAN id. If VLAN is disabled , the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12 , fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPCtrlTimer | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4.1.3 | ||
| The timer value for sending IGMP query packet when none was sent by the multicast router in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997. And it recommends a default of 125 seconds. The timeout value must be at least 30 seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | 30..9999 | ||
| swL2IGMPCtrState | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.4.1.4 | ||
| This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(2) - IGMP funtion is disabled for this entry. enable(3) - IGMP funtion is enabled for this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), disable(2), enable(3) | ||
| swL2IGMPQueryInfoTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5 | ||
| The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2IGMPQueryInfoEntry | |||
| swL2IGMPQueryInfoEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5.1 | ||
| Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled. | |||
| OBJECT-TYPE | |||
| SwL2IGMPQueryInfoEntry | |||
| swL2IGMPInfoIndex | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5.1.1 | ||
| This object indicates the IGMP query information entry number. It could be up to 12 entries, depending on current number of VLAN entries. | |||
| OBJECT-TYPE | |||
| INTEGER | 1..12 | ||
| swL2IGMPInfoVid | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5.1.2 | ||
| This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable). | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPInfoQueryCount | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5.1.3 | ||
| This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPInfoTxQueryCount | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.5.1.4 | ||
| This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPInfoTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6 | ||
| The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2IGMPInfoEntry | |||
| swL2IGMPInfoEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1 | ||
| Information about current IGMP information which captured by this device , provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. | |||
| OBJECT-TYPE | |||
| SwL2IGMPInfoEntry | |||
| swL2IGMPVid | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1.1 | ||
| This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2IGMPGroupIpAddr | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1.2 | ||
| This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| swL2IGMPMacAddr | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1.3 | ||
| This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swL2IGMPPortMap | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1.4 | ||
| This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port . Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.) . The 4 octets is represent one unit port according its logic port . If the unit less 32 port , the other port don't care just fill zero . | |||
| OBJECT-TYPE | |||
| PortList | |||
| swL2IGMPIpGroupReportCount | 1.3.6.1.4.1.326.2.20.1.11.32.2.10.6.1.5 | ||
| This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis. . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PriorityMgmt | 1.3.6.1.4.1.326.2.20.1.11.32.2.11 | ||
| OBJECT IDENTIFIER | |||
| swL2PriorityAddrConfig | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1 | ||
| OBJECT IDENTIFIER | |||
| swL2PriorityAddrMaxSupportedEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.1 | ||
| Maximum number of entries in the MAC address queuing priority control table (swL2PriorityAddrCtrlTable) . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PriorityAddrCurrentTotalEntries | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.2 | ||
| Current applied number of entries in the MAC address priority control table . | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| swL2PriorityAddrCtrlTable | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3 | ||
| This table defines information for the device to decide queuing specific MAC address to a specific priority level queue . The MAC address can be a unicast/multicast address packet . The priority level is from 0 to 3 , the priority level 3 have the highest priority weight . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwL2PriorityAddrCtrlEntry | |||
| swL2PriorityAddrCtrlEntry | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3.1 | ||
| A list of information about a specific unicast/multicast MAC address must be transmited to a specific priority queue for which the switch has priority information . | |||
| OBJECT-TYPE | |||
| SwL2PriorityAddrCtrlEntry | |||
| swL2PriorityAddrVid | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3.1.1 | ||
| This object indicates the VLAN-ID. If VLAN is in disabled mode, the object indicates the default VLAN-ID (0) . | |||
| OBJECT-TYPE | |||
| VlanIndex | |||
| swL2PriorityAddrMac | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3.1.2 | ||
| This object indicates a unicast/multicast MAC address for which the switch has priority information . But if the swL2PriorityAddrState = src-addr then the object can not be a multicast MAC address . | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| swL2PriorityAddrL2PrioLevel | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3.1.3 | ||
| This object indicates the priority level . The priority level 3 has the highest priority weight . The object specify the MAC address should be queued which priority queue . The priority level will over the priority level in a 802.1D . | |||
| OBJECT-TYPE | |||
| INTEGER | 0..3 | ||
| swL2PriorityAddrState | 1.3.6.1.4.1.326.2.20.1.11.32.2.11.1.3.1.4 | ||
| This object indicates the status of this entry . other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values . dst-addr(2) - specific frames's destination address are currently used to be the priority queue as it meets with the MAC address entry of the table . src-addr(3) - specific frames's source address are currently used to be corresponding priority queue as it meets with the MAC address entry of the table . dst-src-addr(4) - specific frames's destination address or source address are currently used to be corresponding priority queue as it meets with the MAC address entry of the table . invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table . | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), dst-addr(2), src-addr(3), dst-src-addr(4), invalid(5) | ||
| swL2MgmtMIBTraps | 1.3.6.1.4.1.326.2.20.1.11.32.2.12 | ||
| OBJECT IDENTIFIER | |||
| swL2MgmtMIBTrapPrefix | 1.3.6.1.4.1.326.2.20.1.11.32.2.12.0 | ||
| OBJECT IDENTIFIER | |||
| swL2linkChangeEvent | 1.3.6.1.4.1.326.2.20.1.11.32.2.12.0.1 | ||
| The trap is sent whenever the link state of a port changes from link up to link down or from link down to link up | |||
| NOTIFICATION-TYPE | |||
| swL2PortInfoUnitIndex | |||
| swL2PortInfoModuleIndex | |||
| swL2PortInfoPortIndex | |||
| swL2addressTableFull | 1.3.6.1.4.1.326.2.20.1.11.32.2.12.0.2 | ||
| The trap is sent whenever the address table is full . | |||
| NOTIFICATION-TYPE | |||
| PortList | |||
| OCTET STRING | |||
| VlanIndex | |||
| Unsigned32 | |||
| SwL2UnitCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2UnitCtrlUnitIndex | |||
| DisplayString as swL2UnitCtrlSwFileName | |||
| INTEGER as swL2UnitCtrlSwUpdateCtrl | |||
| SwL2PortInfoEntry | |||
| SEQUENCE | |||
| INTEGER as swL2PortInfoUnitIndex | |||
| INTEGER as swL2PortInfoModuleIndex | |||
| INTEGER as swL2PortInfoPortIndex | |||
| INTEGER as swL2PortInfoType | |||
| DisplayString as swL2PortInfoDescr | |||
| INTEGER as swL2PortInfoLinkStatus | |||
| INTEGER as swL2PortInfoNwayStatus | |||
| SwL2PortCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2PortCtrlUnitIndex | |||
| INTEGER as swL2PortCtrlModuleIndex | |||
| INTEGER as swL2PortCtrlPortIndex | |||
| INTEGER as swL2PortCtrlAdminState | |||
| INTEGER as swL2PortCtrlNwayState | |||
| INTEGER as swL2PortCtrlFlowCtrlState | |||
| INTEGER as swL2PortCtrlBackPressState | |||
| INTEGER as swL2PortCtrlBMStromPercentage | |||
| SwL2PortTxPrioQueueCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2PortTxPrioQueueUnitIndex | |||
| INTEGER as swL2PortTxPrioQueueModuleIndex | |||
| INTEGER as swPortTxPrioQueueCtrlPortIndex | |||
| INTEGER as swL2PortTxPrioQueuePrioAlgorithm | |||
| INTEGER as swL2PortTxPrioQueueQ0Weight | |||
| INTEGER as swL2PortTxPrioQueueQ1Weight | |||
| INTEGER as swL2PortTxPrioQueueQ2Weight | |||
| INTEGER as swL2PortTxPrioQueueQ3Weight | |||
| SwL2PortStEntry | |||
| SEQUENCE | |||
| INTEGER as swL2PortStUnitIndex | |||
| INTEGER as swL2PortStModuleIndex | |||
| INTEGER as swL2PortStPortlndex | |||
| Counter32 as swL2PortStRxBytes | |||
| Counter32 as swL2PortStRxPkts | |||
| Counter32 as swL2PortStRxCRCErrorPkts | |||
| Counter32 as swL2PortStRxVlanDetected | |||
| Counter32 as swL2PortStRxMcastPkts | |||
| Counter32 as swL2PortStRxBcastPkts | |||
| Counter32 as swL2PortStRxUndersizePkts | |||
| Counter32 as swL2PortStRxOversizePkts | |||
| Counter32 as swL2PortStRxFragmentsPkts | |||
| Counter32 as swL2PortStRxJabbersPkts | |||
| Counter32 as swL2PortStRx64OctsPkts | |||
| Counter32 as swL2PortStRx65To127OctsPkts | |||
| Counter32 as swL2PortStRx128To255OctsPkts | |||
| Counter32 as swL2PortStRx256To511OctsPkts | |||
| Counter32 as swL2PortStRx512To1023OctsPkts | |||
| Counter32 as swL2PortStRx1024To1518OctsPkts | |||
| Counter32 as swL2PortStTxBytes | |||
| Counter32 as swL2PortStTxTotalBytes | |||
| Counter32 as swL2PortStTxPkts | |||
| Counter32 as swL2PortStTxExDeferPkts | |||
| Counter32 as swL2PortStTxGiantPkts | |||
| Counter32 as swL2PortStTxUnderRunPkts | |||
| Counter32 as swL2PortStTxCRCErrorPkts | |||
| Counter32 as swL2PortStTxLenCheckErrorPkts | |||
| Counter32 as swL2PortStTxLenOutRangePkts | |||
| Counter32 as swL2PortStTxLateCollPkts | |||
| Counter32 as swL2PortStTxExCollPkts | |||
| Counter32 as swL2PortStTxSingleCollPkts | |||
| Counter32 as swL2PortStTxCollPkts | |||
| Counter32 as swL2PortStRxDropPkts | |||
| Counter32 as swL2PortStRxLocalDropPkts | |||
| Counter64 as swL2PortStHCRxBytes | |||
| Counter64 as swL2PortStHCRxPkts | |||
| Counter64 as swL2PortStHCTxBytes | |||
| Counter64 as swL2PortStHCTxPkts | |||
| SwL2McastFdbStaticEntry | |||
| SEQUENCE | |||
| MacAddress as swL2McastFdbStaticAddress | |||
| PortList as swL2McastFdbStaticPortMap | |||
| INTEGER as swL2McastFdbStaticJoinIGMP | |||
| INTEGER as swL2McastFdbStaticState | |||
| INTEGER as swL2McastFdbStaticstatus | |||
| SwL2FilterAddrCtrlEntry | |||
| SEQUENCE | |||
| VlanIndex as swL2FilterAddrVid | |||
| MacAddress as swL2FilterAddrMacIndex | |||
| INTEGER as swL2FilterAddrState | |||
| SwL2TrunkCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2TrunkIndex | |||
| DisplayString as swL2TrunkName | |||
| INTEGER as swL2TrunkMasterPortIndex | |||
| INTEGER as swL2TrunkMemberNum | |||
| INTEGER as swL2TrunkState | |||
| SwL2MirrorPortCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2MirrorPortLogicSourcePort | |||
| INTEGER as swL2MirrorPortSourceDirection | |||
| INTEGER as swL2MirrorPortState | |||
| SwL2IGMPCtrlEntry | |||
| SEQUENCE | |||
| INTEGER as swL2IGMPCtrlIndex | |||
| INTEGER as swL2IGMPCtrlVid | |||
| INTEGER as swL2IGMPCtrlTimer | |||
| INTEGER as swL2IGMPCtrState | |||
| SwL2IGMPQueryInfoEntry | |||
| SEQUENCE | |||
| INTEGER as swL2IGMPInfoIndex | |||
| INTEGER as swL2IGMPInfoVid | |||
| INTEGER as swL2IGMPInfoQueryCount | |||
| INTEGER as swL2IGMPInfoTxQueryCount | |||
| SwL2IGMPInfoEntry | |||
| SEQUENCE | |||
| INTEGER as swL2IGMPVid | |||
| IpAddress as swL2IGMPGroupIpAddr | |||
| MacAddress as swL2IGMPMacAddr | |||
| PortList as swL2IGMPPortMap | |||
| INTEGER as swL2IGMPIpGroupReportCount | |||
| SwL2PriorityAddrCtrlEntry | |||
| SEQUENCE | |||
| VlanIndex as swL2PriorityAddrVid | |||
| MacAddress as swL2PriorityAddrMac | |||
| INTEGER as swL2PriorityAddrL2PrioLevel | |||
| INTEGER as swL2PriorityAddrState | |||