TE-LINK-STD-MIB

File: TE-LINK-STD-MIB.mib (62750 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
IF-MIB INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE transmission
Integer32 Unsigned32 MODULE-COMPLIANCE
OBJECT-GROUP TEXTUAL-CONVENTION RowStatus
StorageType InterfaceIndexOrZero ifIndex
InetAddressType InetAddress

Defined Objects

teLinkStdMIB 1.3.6.1.2.1.10.200
Copyright (C) 2005 The Internet Society. This version of this MIB module is part of RFC 4220; see the RFC itself for full legal notices. This MIB module contains managed object definitions for MPLS traffic engineering links as defined in 'Link Bundling in MPLS Traffic Engineering (TE)'.
MODULE-IDENTITY    

teLinkNotifications 1.3.6.1.2.1.10.200.0
OBJECT IDENTIFIER    

teLinkObjects 1.3.6.1.2.1.10.200.1
OBJECT IDENTIFIER    

teLinkTable 1.3.6.1.2.1.10.200.1.1
This table specifies the grouping of component links into TE links and the grouping of TE links into bundled links.
OBJECT-TYPE    
  SEQUENCE OF  
    TeLinkEntry

teLinkEntry 1.3.6.1.2.1.10.200.1.1.1
An entry in this table exists for each ifEntry with an ifType of teLink(200), i.e., for every TE link. An ifEntry in the ifTable must exist before a teLinkEntry is created with the corresponding ifIndex. If a TE link entry in the ifTable is destroyed, then so is the corresponding entry in the teLinkTable. The administrative and operational status values are controlled from the ifEntry.
OBJECT-TYPE    
  TeLinkEntry  

teLinkAddressType 1.3.6.1.2.1.10.200.1.1.1.1
The type of Internet address for the TE link.
OBJECT-TYPE    
  InetAddressType  

teLinkLocalIpAddr 1.3.6.1.2.1.10.200.1.1.1.2
The local Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. For IPv4 and IPv6 numbered links, this object represents the local IP address associated with the TE link. For an unnumbered link, the local address is of type unknown, this object is set to the zero length string, and the teLinkOutgoingIfId object then identifies the unnumbered address. If the TE link is a Forwarding Adjacency (FA), the local IP address is set to the head-end address of the FA-LSP. If ipAddrTable is implemented, this object must have the same value as the ipAdEntAddr object that belongs to the row in ipAddrTable where ipAdEntIfIndex is equal to ifIndex.
OBJECT-TYPE    
  InetAddress  

teLinkRemoteIpAddr 1.3.6.1.2.1.10.200.1.1.1.3
The remote Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. The remote IP address associated with the TE link (IPv4 and IPv6 numbered links). For an unnumbered link, the remote address is of type unknown, this object is set to the zero length string, and the teLinkIncomingIfId object then identifies the unnumbered address. If the TE link is a Forwarding Adjacency, the remote IP address is set to the tail-end address of the FA-LSP.
OBJECT-TYPE    
  InetAddress  

teLinkMetric 1.3.6.1.2.1.10.200.1.1.1.4
The traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric.
OBJECT-TYPE    
  Unsigned32  

teLinkMaximumReservableBandwidth 1.3.6.1.2.1.10.200.1.1.1.5
This attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkProtectionType 1.3.6.1.2.1.10.200.1.1.1.6
This attribute specifies the link protection type of the TE link. Descriptions of the different protection types can be found in the 'Routing Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)' document.
OBJECT-TYPE    
  INTEGER extraTraffic(1), unprotected(2), shared(3), dedicated1For1(4), dedicated1Plus1(5), enhanced(6)  

teLinkWorkingPriority 1.3.6.1.2.1.10.200.1.1.1.7
This object represents a priority value such that a new connection with a higher priority, i.e., numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link.
OBJECT-TYPE    
  TeLinkPriority  

teLinkResourceClass 1.3.6.1.2.1.10.200.1.1.1.8
This attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within a link bundle must have the same resource class. Encoding of the resource class is described in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.
OBJECT-TYPE    
  Unsigned32  

teLinkIncomingIfId 1.3.6.1.2.1.10.200.1.1.1.9
For unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link. If the link is numbered, the value of this object is 0 and the address is stored in the teLinkRemoteIpAddr instead.
OBJECT-TYPE    
  Integer32 0..2147483647  

teLinkOutgoingIfId 1.3.6.1.2.1.10.200.1.1.1.10
If the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR. If the link is numbered, the value of this object is 0 and the address is stored in the teLinkLocalIpAddr instead.
OBJECT-TYPE    
  InterfaceIndexOrZero  

teLinkRowStatus 1.3.6.1.2.1.10.200.1.1.1.11
This variable is used to create, modify, and/or delete a row in this table. None of the writable objects in a row can be changed if status is active(1).
OBJECT-TYPE    
  RowStatus  

teLinkStorageType 1.3.6.1.2.1.10.200.1.1.1.12
The storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

teLinkDescriptorTable 1.3.6.1.2.1.10.200.1.2
This table specifies the interface switching capability descriptors associated with the TE links.
OBJECT-TYPE    
  SEQUENCE OF  
    TeLinkDescriptorEntry

teLinkDescriptorEntry 1.3.6.1.2.1.10.200.1.2.1
An entry in this table is created for every TE link interface switching capability descriptor. An ifEntry in the ifTable must exist before a teLinkDescriptorEntry using the same ifIndex is created. ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkDescriptorTable that use the ifIndex of this TE link.
OBJECT-TYPE    
  TeLinkDescriptorEntry  

teLinkDescriptorId 1.3.6.1.2.1.10.200.1.2.1.1
This object specifies the link descriptor identifier.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

teLinkDescrSwitchingCapability 1.3.6.1.2.1.10.200.1.2.1.2
This attribute specifies interface switching capability of the TE link, which is derived from its component links.
OBJECT-TYPE    
  TeLinkSwitchingCapability  

teLinkDescrEncodingType 1.3.6.1.2.1.10.200.1.2.1.3
This attribute specifies the TE link encoding type.
OBJECT-TYPE    
  TeLinkEncodingType  

teLinkDescrMinLspBandwidth 1.3.6.1.2.1.10.200.1.2.1.4
This attribute specifies the minimum LSP bandwidth on the TE link. This is derived from the union of the minimum LSP bandwidth of all the component links associated with the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio0 1.3.6.1.2.1.10.200.1.2.1.5
This attribute specifies the maximum LSP bandwidth at priority 0 on the TE link. This is the union of the maximum LSP bandwidth at priority 0 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio1 1.3.6.1.2.1.10.200.1.2.1.6
This attribute specifies the maximum LSP bandwidth at priority 1 on the TE link. This is the union of the maximum LSP bandwidth at priority 1 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio2 1.3.6.1.2.1.10.200.1.2.1.7
This attribute specifies the maximum LSP bandwidth at priority 2 on the TE link. This is the union of the maximum LSP bandwidth at priority 2 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio3 1.3.6.1.2.1.10.200.1.2.1.8
This attribute specifies the maximum LSP bandwidth at priority 3 on the TE link. This is the union of the maximum LSP bandwidth at priority 3 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio4 1.3.6.1.2.1.10.200.1.2.1.9
This attribute specifies the maximum LSP bandwidth at priority 4 on the TE link. This is the union of the maximum LSP bandwidth at priority 4 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio5 1.3.6.1.2.1.10.200.1.2.1.10
This attribute specifies the maximum LSP bandwidth at priority 5 on the TE link. This is the union of the maximum LSP bandwidth at priority 5 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio6 1.3.6.1.2.1.10.200.1.2.1.11
This attribute specifies the maximum LSP bandwidth at priority 6 on the TE link. This is the union of the maximum LSP bandwidth at priority 6 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrMaxLspBandwidthPrio7 1.3.6.1.2.1.10.200.1.2.1.12
This attribute specifies the maximum LSP bandwidth at priority 7 on the TE link. This is the union of the maximum LSP bandwidth at priority 7 of all the component links within the TE link that can be used to carry live traffic.
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkDescrInterfaceMtu 1.3.6.1.2.1.10.200.1.2.1.13
This attribute specifies the interface MTU for the TE link descriptor.
OBJECT-TYPE    
  Unsigned32 1..65535  

teLinkDescrIndication 1.3.6.1.2.1.10.200.1.2.1.14
This attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.
OBJECT-TYPE    
  TeLinkSonetSdhIndication  

teLinkDescrRowStatus 1.3.6.1.2.1.10.200.1.2.1.15
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be changed if teLinkDescrRowStatus is in the active(1) state.
OBJECT-TYPE    
  RowStatus  

teLinkDescrStorageType 1.3.6.1.2.1.10.200.1.2.1.16
The storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

teLinkSrlgTable 1.3.6.1.2.1.10.200.1.3
This table specifies the SRLGs associated with TE links.
OBJECT-TYPE    
  SEQUENCE OF  
    TeLinkSrlgEntry

teLinkSrlgEntry 1.3.6.1.2.1.10.200.1.3.1
An entry in this table contains information about an SRLG associated with a TE link. An ifEntry in the ifTable must exist before a teLinkSrlgEntry using the same ifIndex is created. The ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkSrlgTable that use the ifIndex of this TE link.
OBJECT-TYPE    
  TeLinkSrlgEntry  

teLinkSrlg 1.3.6.1.2.1.10.200.1.3.1.1
This identifies an SRLG supported by the TE link. An SRLG is identified with a 32-bit number that is unique within an IGP domain. Zero is a valid SRLG number.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

teLinkSrlgRowStatus 1.3.6.1.2.1.10.200.1.3.1.2
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified if teLinkSrlgRowStatus is active(1).
OBJECT-TYPE    
  RowStatus  

teLinkSrlgStorageType 1.3.6.1.2.1.10.200.1.3.1.3
The storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

teLinkBandwidthTable 1.3.6.1.2.1.10.200.1.4
This table specifies the priority-based bandwidth table for TE links.
OBJECT-TYPE    
  SEQUENCE OF  
    TeLinkBandwidthEntry

teLinkBandwidthEntry 1.3.6.1.2.1.10.200.1.4.1
An entry in this table contains information about the priority-based bandwidth of TE links. An ifEntry in the ifTable must exist before a teLinkBandwidthEntry using the same ifIndex is created. The ifType of ifEntry must be teLink(200). If a TE link entry in the ifTable is destroyed, then so are all of the entries in the teLinkBandwidthTable that use the ifIndex of this TE link.
OBJECT-TYPE    
  TeLinkBandwidthEntry  

teLinkBandwidthPriority 1.3.6.1.2.1.10.200.1.4.1.1
This attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.
OBJECT-TYPE    
  TeLinkPriority  

teLinkBandwidthUnreserved 1.3.6.1.2.1.10.200.1.4.1.2
This attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excluding all links that are strictly used as protecting links).
OBJECT-TYPE    
  TeLinkBandwidth  

teLinkBandwidthRowStatus 1.3.6.1.2.1.10.200.1.4.1.3
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when teLinkBandwidthRowStatus is active(1).
OBJECT-TYPE    
  RowStatus  

teLinkBandwidthStorageType 1.3.6.1.2.1.10.200.1.4.1.4
The storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

componentLinkTable 1.3.6.1.2.1.10.200.1.5
This table specifies the component link parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    ComponentLinkEntry

componentLinkEntry 1.3.6.1.2.1.10.200.1.5.1
An entry in this table exists for each ifEntry that represents a component link. An ifEntry must exist in the ifTable before a componentLinkEntry is created with the corresponding ifIndex. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If an entry representing a component link is destroyed in the ifTable, then so is the corresponding entry in the componentLinkTable. The administrative and operational status values are controlled from the ifEntry.
OBJECT-TYPE    
  ComponentLinkEntry  

componentLinkMaxResBandwidth 1.3.6.1.2.1.10.200.1.5.1.1
This attribute specifies the maximum reservable bandwidth on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkPreferredProtection 1.3.6.1.2.1.10.200.1.5.1.2
This attribute specifies whether this component link is a primary or secondary entity.
OBJECT-TYPE    
  TeLinkProtection  

componentLinkCurrentProtection 1.3.6.1.2.1.10.200.1.5.1.3
This attribute specifies whether this component link is currently used as primary or secondary link.
OBJECT-TYPE    
  TeLinkProtection  

componentLinkRowStatus 1.3.6.1.2.1.10.200.1.5.1.4
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkRowStatus is active(1).
OBJECT-TYPE    
  RowStatus  

componentLinkStorageType 1.3.6.1.2.1.10.200.1.5.1.5
The storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

componentLinkDescriptorTable 1.3.6.1.2.1.10.200.1.6
This table specifies the interface switching capability descriptors associated with the component links.
OBJECT-TYPE    
  SEQUENCE OF  
    ComponentLinkDescriptorEntry

componentLinkDescriptorEntry 1.3.6.1.2.1.10.200.1.6.1
An entry in this table is created for every component link descriptor. An ifEntry in the ifTable must exist before a componentLinkDescriptorEntry using the same ifIndex is created. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkDescriptorTable that use the ifIndex of this component link.
OBJECT-TYPE    
  ComponentLinkDescriptorEntry  

componentLinkDescrId 1.3.6.1.2.1.10.200.1.6.1.1
This object specifies the link descriptor identifier.
OBJECT-TYPE    
  Unsigned32 1..4294967295  

componentLinkDescrSwitchingCapability 1.3.6.1.2.1.10.200.1.6.1.2
This attribute specifies link multiplexing capabilities of the component link.
OBJECT-TYPE    
  TeLinkSwitchingCapability  

componentLinkDescrEncodingType 1.3.6.1.2.1.10.200.1.6.1.3
This attribute specifies the component link encoding type.
OBJECT-TYPE    
  TeLinkEncodingType  

componentLinkDescrMinLspBandwidth 1.3.6.1.2.1.10.200.1.6.1.4
This attribute specifies the minimum LSP bandwidth on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio0 1.3.6.1.2.1.10.200.1.6.1.5
This attribute specifies the maximum LSP bandwidth at priority 0 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio1 1.3.6.1.2.1.10.200.1.6.1.6
This attribute specifies the maximum LSP bandwidth at priority 1 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio2 1.3.6.1.2.1.10.200.1.6.1.7
This attribute specifies the maximum LSP bandwidth at priority 2 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio3 1.3.6.1.2.1.10.200.1.6.1.8
This attribute specifies the maximum LSP bandwidth at priority 3 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio4 1.3.6.1.2.1.10.200.1.6.1.9
This attribute specifies the maximum LSP bandwidth at priority 4 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio5 1.3.6.1.2.1.10.200.1.6.1.10
This attribute specifies the maximum LSP bandwidth at priority 5 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio6 1.3.6.1.2.1.10.200.1.6.1.11
This attribute specifies the maximum LSP bandwidth at priority 6 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrMaxLspBandwidthPrio7 1.3.6.1.2.1.10.200.1.6.1.12
This attribute specifies the maximum LSP bandwidth at priority 7 on the component link.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkDescrInterfaceMtu 1.3.6.1.2.1.10.200.1.6.1.13
This attribute specifies the interface MTU for the component link descriptor.
OBJECT-TYPE    
  Unsigned32 1..65535  

componentLinkDescrIndication 1.3.6.1.2.1.10.200.1.6.1.14
This attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.
OBJECT-TYPE    
  TeLinkSonetSdhIndication  

componentLinkDescrRowStatus 1.3.6.1.2.1.10.200.1.6.1.15
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkDescrRowStatus is active(1).
OBJECT-TYPE    
  RowStatus  

componentLinkDescrStorageType 1.3.6.1.2.1.10.200.1.6.1.16
The storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

componentLinkBandwidthTable 1.3.6.1.2.1.10.200.1.7
This table specifies the priority-based bandwidth for component links.
OBJECT-TYPE    
  SEQUENCE OF  
    ComponentLinkBandwidthEntry

componentLinkBandwidthEntry 1.3.6.1.2.1.10.200.1.7.1
An entry in this table contains information about the priority-based bandwidth on component links. An ifEntry in the ifTable must exist before a componentLinkBandwidthEntry using the same ifIndex is created. ifEntry's ifType can be of any interface type that has been defined for TE Link interworking. Examples include ATM, Frame Relay, Ethernet, etc. If a component link entry in the ifTable is destroyed, then so are all entries in the componentLinkBandwidthTable that use the ifIndex of this component link.
OBJECT-TYPE    
  ComponentLinkBandwidthEntry  

componentLinkBandwidthPriority 1.3.6.1.2.1.10.200.1.7.1.1
This attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.
OBJECT-TYPE    
  TeLinkPriority  

componentLinkBandwidthUnreserved 1.3.6.1.2.1.10.200.1.7.1.2
This attribute specifies the component link unreserved bandwidth at priority p.
OBJECT-TYPE    
  TeLinkBandwidth  

componentLinkBandwidthRowStatus 1.3.6.1.2.1.10.200.1.7.1.3
This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkBandwidthRowStatus is active(1).
OBJECT-TYPE    
  RowStatus  

componentLinkBandwidthStorageType 1.3.6.1.2.1.10.200.1.7.1.4
The storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.
OBJECT-TYPE    
  StorageType  

teLinkConformance 1.3.6.1.2.1.10.200.2
OBJECT IDENTIFIER    

teLinkCompliances 1.3.6.1.2.1.10.200.2.1
OBJECT IDENTIFIER    

teLinkModuleFullCompliance 1.3.6.1.2.1.10.200.2.1.1
Compliance statement for agents that support read-create so that both configuration and monitoring of TE links can be accomplished via this MIB module.
MODULE-COMPLIANCE    

teLinkModuleReadOnlyCompliance 1.3.6.1.2.1.10.200.2.1.2
Compliance statement for agents that support the monitoring of the TE link MIB module.
MODULE-COMPLIANCE    

teLinkGroups 1.3.6.1.2.1.10.200.2.2
OBJECT IDENTIFIER    

teLinkGroup 1.3.6.1.2.1.10.200.2.2.1
Collection of objects needed for the management of resources associated with TE links.
OBJECT-GROUP    

teLinkSrlgGroup 1.3.6.1.2.1.10.200.2.2.2
Collection of objects needed for the management of SRLG resources associated with TE links.
OBJECT-GROUP    

teLinkBandwidthGroup 1.3.6.1.2.1.10.200.2.2.3
Collection of objects needed for the management of the bandwidth resources associated with TE links and component links.
OBJECT-GROUP    

componentLinkBandwidthGroup 1.3.6.1.2.1.10.200.2.2.4
Collection of objects needed for the management of the bandwidth parameters associated with component links.
OBJECT-GROUP    

teLinkPscGroup 1.3.6.1.2.1.10.200.2.2.5
Collection of objects needed for devices that are packet switch capable.
OBJECT-GROUP    

teLinkTdmGroup 1.3.6.1.2.1.10.200.2.2.6
Collection of objects needed for devices that are TDM switching capable.
OBJECT-GROUP    

Defined Objects

TeLinkBandwidth  
This type is used to represent link bandwidth in bps. This value is represented using a 4 octet IEEE floating point format [IEEE]. The floating point representation is not used to represent fractional value but rather to allow specification of large numbers that cannot be expressed with 32-bit integers.
TEXTUAL-CONVENTION    
  OCTET STRING SIZE(4)  

TeLinkPriority  
This type is used to represent a priority. Each connection is assigned a priority. This priority is used when accounting for bandwidth on TE links or component links, for resource allocation and for rerouting purposes. Value 0 is the highest priority. Value 7 is the lowest priority.
TEXTUAL-CONVENTION    
  Unsigned32 0..7  

TeLinkProtection  
Link protection.
TEXTUAL-CONVENTION    
  INTEGER primary(1), secondary(2)  

TeLinkSwitchingCapability  
Switching capability as specified in the 'OSPF Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)' document. The values specified in this document are not contiguous.
TEXTUAL-CONVENTION    
  INTEGER packetSwitch1(1), packetSwitch2(2), packetSwitch3(3), packetSwitch4(4), layer2Switch(51), tdm(100), lambdaSwitch(150), fiberSwitch(200)  

TeLinkEncodingType  
Link encoding type as specified in 'Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description' document. The values specified in this document are not contiguous.
TEXTUAL-CONVENTION    
  INTEGER packet(1), ethernet(2), ansiEtsiPdh(3), sdhItuSonetAnsi(5), digitalWrapper(7), lambda(8), fiber(9), fiberChannel(11)  

TeLinkSonetSdhIndication  
This convention is used to indicate whether the interface supports Standard or Arbitrary SONET/SDH. To simplify the mapping process, the values used in this textual convention match the values specified in the interface switching capability specific information field, i.e., 0 for Standard SONET/SDH and 1 for Arbitrary SONET/SDH.
TEXTUAL-CONVENTION    
  INTEGER standard(0), arbitrary(1)  

TeLinkEntry  
SEQUENCE    
  InetAddressType as teLinkAddressType  
  InetAddress as teLinkLocalIpAddr  
  InetAddress as teLinkRemoteIpAddr  
  Unsigned32 as teLinkMetric  
  TeLinkBandwidth as teLinkMaximumReservableBandwidth  
  INTEGER as teLinkProtectionType  
  TeLinkPriority as teLinkWorkingPriority  
  Unsigned32 as teLinkResourceClass  
  Integer32 as teLinkIncomingIfId  
  InterfaceIndexOrZero as teLinkOutgoingIfId  
  RowStatus as teLinkRowStatus  
  StorageType as teLinkStorageType  

TeLinkDescriptorEntry  
SEQUENCE    
  Unsigned32 as teLinkDescriptorId  
  TeLinkSwitchingCapability as teLinkDescrSwitchingCapability  
  TeLinkEncodingType as teLinkDescrEncodingType  
  TeLinkBandwidth as teLinkDescrMinLspBandwidth  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio0  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio1  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio2  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio3  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio4  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio5  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio6  
  TeLinkBandwidth as teLinkDescrMaxLspBandwidthPrio7  
  Unsigned32 as teLinkDescrInterfaceMtu  
  TeLinkSonetSdhIndication as teLinkDescrIndication  
  RowStatus as teLinkDescrRowStatus  
  StorageType as teLinkDescrStorageType  

TeLinkSrlgEntry  
SEQUENCE    
  Unsigned32 as teLinkSrlg  
  RowStatus as teLinkSrlgRowStatus  
  StorageType as teLinkSrlgStorageType  

TeLinkBandwidthEntry  
SEQUENCE    
  TeLinkPriority as teLinkBandwidthPriority  
  TeLinkBandwidth as teLinkBandwidthUnreserved  
  RowStatus as teLinkBandwidthRowStatus  
  StorageType as teLinkBandwidthStorageType  

ComponentLinkEntry  
SEQUENCE    
  TeLinkBandwidth as componentLinkMaxResBandwidth  
  TeLinkProtection as componentLinkPreferredProtection  
  TeLinkProtection as componentLinkCurrentProtection  
  RowStatus as componentLinkRowStatus  
  StorageType as componentLinkStorageType  

ComponentLinkDescriptorEntry  
SEQUENCE    
  Unsigned32 as componentLinkDescrId  
  TeLinkSwitchingCapability as componentLinkDescrSwitchingCapability  
  TeLinkEncodingType as componentLinkDescrEncodingType  
  TeLinkBandwidth as componentLinkDescrMinLspBandwidth  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio0  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio1  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio2  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio3  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio4  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio5  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio6  
  TeLinkBandwidth as componentLinkDescrMaxLspBandwidthPrio7  
  Unsigned32 as componentLinkDescrInterfaceMtu  
  TeLinkSonetSdhIndication as componentLinkDescrIndication  
  RowStatus as componentLinkDescrRowStatus  
  StorageType as componentLinkDescrStorageType  

ComponentLinkBandwidthEntry  
SEQUENCE    
  TeLinkPriority as componentLinkBandwidthPriority  
  TeLinkBandwidth as componentLinkBandwidthUnreserved  
  RowStatus as componentLinkBandwidthRowStatus  
  StorageType as componentLinkBandwidthStorageType