ACE20-MIB

File: ACE20-MIB.mib (116616 bytes)

Imported modules

RAD-MIB IF-MIB RFC1155-SMI
SNMPv2-SMI SNMPv2-TC ATM-MIB

Imported symbols

TimeSlots radAtm agnLed
agnIndication alarmSeverity alarmState
ifAlias OBJECT-TYPE IpAddress
NOTIFICATION-TYPE OBJECT-IDENTITY Counter32
Integer32 TEXTUAL-CONVENTION DisplayString
RowStatus TimeStamp MacAddress
AtmTrafficDescrParamIndex

Defined Objects

radAtmEvents 1.3.6.1.4.1.164.12.0
The events for RAD ATM.
OBJECT-IDENTITY    

alarmTrap 1.3.6.1.4.1.164.12.0.1
This trap is sent whenever an alarm occurs in the agent.
NOTIFICATION-TYPE    

statusChangeTrap 1.3.6.1.4.1.164.12.0.2
This trap is sent whenever a led in the agent change it's status.
NOTIFICATION-TYPE    
  agnLed  
  agnIndication  

atmSuAgnNoBufferToNetwork 1.3.6.1.4.1.164.12.0.3
This trap usualy indicates timing problem; incorrect selection of timing references between end users.
NOTIFICATION-TYPE    
  alarmSeverity  

atmSuJitterBufferOverrun 1.3.6.1.4.1.164.12.0.4
This trap indicates that an overrun event occurred in the ATM jitter buffer serving the transmit to user direction of the user interface specified by ifAlias
NOTIFICATION-TYPE    
  alarmSeverity  
  ifAlias  

atmSuJitterBufferUnderrun 1.3.6.1.4.1.164.12.0.5
This trap indicates that an underrun event occurred in the atm jitter buffer serving the transmit to user direction of the user interface specified by ifAlias.
NOTIFICATION-TYPE    
  alarmSeverity  
  ifAlias  

atmSuDataLocalLoopbackTrap 1.3.6.1.4.1.164.12.0.6
This trap indicates that a local loopback has been activated on the local data port.
NOTIFICATION-TYPE    
  alarmSeverity  
  alarmState  
  ifAlias  

atmSuDataRemoteLoopbackTrap 1.3.6.1.4.1.164.12.0.7
This trap indicates that a remote loopback has been activated on the local data port.
NOTIFICATION-TYPE    
  alarmSeverity  
  alarmState  
  ifAlias  

atmSu 1.3.6.1.4.1.164.12.4
OBJECT IDENTIFIER    

atmSuSystem 1.3.6.1.4.1.164.12.4.1
OBJECT IDENTIFIER    

atmSuSystemSwOperStatus 1.3.6.1.4.1.164.12.4.1.1
This value indicates if tftp-write operation (for downloading software from an external host) is allowed by the agent.
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

atmSuSystemSwSwitchVersionsCmd 1.3.6.1.4.1.164.12.4.1.2
This command is used to switch beetween software versions stored in the flash. setting this value to active will reset the agent and re-activate it with the new version ( only if new version is valid). on get-request this value will be always notActive.
OBJECT-TYPE    
  INTEGER notActive(1), active(2)  

atmSuSystemHistoryAlrTable 1.3.6.1.4.1.164.12.4.1.3
buffer contain history buffer of agent alarms.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuSystemHistoryAlrEntry

atmSuSystemHistoryAlrEntry 1.3.6.1.4.1.164.12.4.1.3.1
Agent alarm history list entry.
OBJECT-TYPE    
  AtmSuSystemHistoryAlrEntry  

atmSuSystemHistoryAlrIndex 1.3.6.1.4.1.164.12.4.1.3.1.1
A unique number to identify an entry in the history alarm table.
OBJECT-TYPE    
  Integer32  

atmSuSystemHistoryAlrIfIndex 1.3.6.1.4.1.164.12.4.1.3.1.2
This value indicates the port on which the alarms occured. configuration(system) alarms have port index equal to 0.
OBJECT-TYPE    
  Integer32  

atmSuSystemHistoryAlrDescription 1.3.6.1.4.1.164.12.4.1.3.1.3
This attribute is a text description of the alarm. The alarm descipion include alarm code and alarm text.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

atmSuSystemHistoryAlrStatus 1.3.6.1.4.1.164.12.4.1.3.1.4
This attribute indicates the status of the alarm.
OBJECT-TYPE    
  INTEGER on(1), off(2), event(3)  

atmSuSystemHistoryAlrOccurrenceTime 1.3.6.1.4.1.164.12.4.1.3.1.5
This value indicates the date and time of the occurrence of the event that caused this alarm. Date and time format: YYYY-MM-DD, HH:MM:SS
OBJECT-TYPE    
  DisplayString  

atmSuSystemHistoryAlrVpi 1.3.6.1.4.1.164.12.4.1.3.1.6
This value indicates the ATM VPI of the connection associated with the event that caused this alarm. When not applicable, value is 0
OBJECT-TYPE    
  Integer32  

atmSuSystemHistoryAlrVci 1.3.6.1.4.1.164.12.4.1.3.1.7
This value indicates the ATM VCI of the connection associated with with the event that caused this alarm. When not applicable, value is 0
OBJECT-TYPE    
  Integer32  

atmSuSystemClearHistoryAlrListCmd 1.3.6.1.4.1.164.12.4.1.4
Setting this attribute to ON, enforce a clear operation on the agent history event buffer . On reading, attribute will always get status 'off' .
OBJECT-TYPE    
  INTEGER off(1), on(2)  

atmSuSystemCurrentAlrTable 1.3.6.1.4.1.164.12.4.1.5
table which contains all alarms Currently active ( status ON ) in the agent.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuSystemCurrentAlrEntry

atmSuSystemCurrentAlrEntry 1.3.6.1.4.1.164.12.4.1.5.1
Agent alarm list entry.
OBJECT-TYPE    
  AtmSuSystemCurrentAlrEntry  

atmSuSystemCurrentAlrIndex 1.3.6.1.4.1.164.12.4.1.5.1.1
A unique number to identify an entry in the Current alarms table.
OBJECT-TYPE    
  Integer32  

atmSuSystemCurrentAlrIfIndex 1.3.6.1.4.1.164.12.4.1.5.1.2
This value indicates the port on which the alarms occured. configuration alarms have port index equal to 0.
OBJECT-TYPE    
  Integer32  

atmSuSystemCurrentAlrDescription 1.3.6.1.4.1.164.12.4.1.5.1.3
This attribute is a text description of the alarm. The alarm descipion include alarm code and alarm text.
OBJECT-TYPE    
  DisplayString SIZE(0..255)  

atmSuSystemILMICommunity 1.3.6.1.4.1.164.12.4.1.6
Community string for ILMI requests. 10 chars.
OBJECT-TYPE    
  DisplayString  

atmSuSystemTrapMaxManagers 1.3.6.1.4.1.164.12.4.1.7
The maximum number of managers that can be registered for receiving traps and sending requests.
OBJECT-TYPE    
  Integer32  

atmSuSystemAalSelection 1.3.6.1.4.1.164.12.4.1.8
Select ATM adaptation layers AAL1 or AAL2 Applicable for LA-140
OBJECT-TYPE    
  INTEGER notApplicable(1), aal2(2), aal1(3)  

atmSuSystemCodingLaw 1.3.6.1.4.1.164.12.4.1.9
This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw (2) is the standard Law for E1 links. uLaw (3) is the standard Law for T1 links. Coding law is applicable for all the ports in the system
OBJECT-TYPE    
  INTEGER notApplicable(1), aLaw(2), uLaw(3)  

atmSuSystemISDNDataLinkActivation 1.3.6.1.4.1.164.12.4.1.10
This attribute indicates data link aactivation for all ISDN ports in the system. nonPermanent (2) = non permanent data link activation permanent (3) = permanent data link activation
OBJECT-TYPE    
  INTEGER notApplicable(1), nonPermanent(2), permanent(3)  

atmSuSystemJitterBuffer 1.3.6.1.4.1.164.12.4.1.11
The field is set in ms and sets the jitter buffer size. The jitter buffer adapts the size of the LA140 traffic to the cdv (cell delay variation) of the ATM network.
OBJECT-TYPE    
  Integer32  

atmSuSystemOperMode 1.3.6.1.4.1.164.12.4.1.12
The field indicates device mode of operation: ima (2) = Inverse Multiplex ATM - ATM traffic is distributed between links in IMA group. miniDSLAM (3) => each link serves as separate ATM interface.
OBJECT-TYPE    
  INTEGER notApplicable(1), ima(2), miniDslam(3)  

atmSuSystemDSPGain 1.3.6.1.4.1.164.12.4.1.13
This object indicates DSP Gain. Range of possible values is -12....12. For LA-110 suset of this range is supported.
OBJECT-TYPE    
  Integer32  

atmSuPort 1.3.6.1.4.1.164.12.4.2
OBJECT IDENTIFIER    

atmSuPortDataCnfgTable 1.3.6.1.4.1.164.12.4.2.1
Data Port global configuration table. this table include parametes which are common to the physical port and not depend on whether the port interface is Frame-Relay or ATM-DXI.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortDataCnfgEntry

atmSuPortDataCnfgEntry 1.3.6.1.4.1.164.12.4.2.1.1
the entries at this table describes the configuration of the Data-Port.
OBJECT-TYPE    
  AtmSuPortDataCnfgEntry  

atmSuPortDataApplication 1.3.6.1.4.1.164.12.4.2.1.1.1
This attribute indicates the protocol application which runs above the physical port.
OBJECT-TYPE    
  INTEGER frameRelay(1), atmDxi(2), bridgedEthernet(3), smdsDxi(4), aal1Stream(5), routedEthernet(6), notApplicable(255)  

atmSuPortDataRate 1.3.6.1.4.1.164.12.4.2.1.1.2
This attribute indicates the operation rate of the port. AmcdT1 / Ace-20T allowes rates up to 1536KBps ( options 1-12 ), while AmcdE1 / Ace-20E allowes all options.
OBJECT-TYPE    
  INTEGER r64KBps(1), r128KBps(2), r192KBps(3), r256KBps(4), r320KBps(5), r384KBps(6), r448KBps(7), r512KBps(8), r576KBps(9), r640KBps(10), r704KBps(11), r768KBps(12), r832KBps(13), r896KBps(14), r960KBps(15), r1024KBps(16), r1088KBps(17), r1152KBps(18), r1216KBps(19), r1280KBps(20), r1344KBps(21), r1408KBps(22), r1472KBps(23), r1536KBps(24), r1544network(25), r1600KBps(26), r1664KBps(27), r1728KBps(28), r1792KBps(29), r1856KBps(30), r1920KBps(31), r1984KBps(32), r2048KBps(33), r2048network(34), r8192KBps(35), notApplicable(255)  

atmSuPortDataDCD 1.3.6.1.4.1.164.12.4.2.1.1.3
This attribute define behavior of control signals DCD and RTS These signals may obey or ignore signal from remote device. The terms 'I signal' and 'C signal' are used when physical data interface is X.21 ; RTS = C signal, DCD = I signal
OBJECT-TYPE    
  INTEGER off(1), on(2), obeyRtsDcdOn(3), obeyRtsDcdOff(4), ignoreRtsDcdOn(5), ignoreRtsDcdOff(6), notApplicable(255)  

atmSuPortDataMode 1.3.6.1.4.1.164.12.4.2.1.1.4
This attribute indicates the port mode of sampling data physical.
OBJECT-TYPE    
  INTEGER nrzi(1), nrz(2), notApplicable(255)  

atmSuPortDataCRC 1.3.6.1.4.1.164.12.4.2.1.1.5
This attribute indicates the type of CRC checking on receiving/transmiting frames.
OBJECT-TYPE    
  INTEGER cRC16(1), cRC32(2), noCRC(3), notApplicable(255)  

atmSuPortDataClock 1.3.6.1.4.1.164.12.4.2.1.1.6
This attribute indicates the clock using for synchronization for the data port.
OBJECT-TYPE    
  INTEGER dce(1), edce(2), dte(3), notApplicable(255)  

atmSuPortDataMaxNoOfConns 1.3.6.1.4.1.164.12.4.2.1.1.7
this object indicates the maximum number of cross-connect connections allowed beetween the ATM port and the Data Port identified by IfIndex.
OBJECT-TYPE    
  Integer32  

atmSuPortDataConfNoOfConns 1.3.6.1.4.1.164.12.4.2.1.1.8
this object indicates the configured number of cross-connect connections exist beetween the ATM port and the Data Port identified by IfIndex.
OBJECT-TYPE    
  Integer32  

atmSuPortDataIdleCode 1.3.6.1.4.1.164.12.4.2.1.1.9
This attribute is applicable only for application aal1Stream. It indicates the value to be transmitted whenever the port is idle.
OBJECT-TYPE    
  Integer32 0..255  

atmSuPortDataInterfaceType 1.3.6.1.4.1.164.12.4.2.1.1.10
Configureable physical layer interface type
OBJECT-TYPE    
  INTEGER notApplicable(1), x21(2), v35(3), v36(4), rs530(5)  

atmSuPortDataClkPolarity 1.3.6.1.4.1.164.12.4.2.1.1.11
This object indicates the clock polarity. For LA-110/140 this object will be applicable only for X.21/V.35/data port
OBJECT-TYPE    
  INTEGER notApplicable(1), normal(2), inverted(3)  

atmSuPortDataCtsStatus 1.3.6.1.4.1.164.12.4.2.1.1.12
CTS status - the signal state received from ATM network (for the local DTE usage). LA110 receiving RTS down from remote DTE device via ATM network, will change CTS signal state to down (off) toward local DTE device
OBJECT-TYPE    
  INTEGER notApplicable(1), off(2), on(3)  

atmSuPortDataRtsStatus 1.3.6.1.4.1.164.12.4.2.1.1.13
RTS status - the signal state received from local DTE (to be forwarded to ATM network). LA110 receiving RTS down from the local DTE device will transmit all '1' to ATM (in order to carry the signaling to remote LA110), and forward it (RTS-down) to far end through ATM cell (pointer field).
OBJECT-TYPE    
  INTEGER notApplicable(1), off(2), on(3)  

atmSuPortDs1 1.3.6.1.4.1.164.12.4.2.2
OBJECT IDENTIFIER    

atmSuPortDs1CnfgTable 1.3.6.1.4.1.164.12.4.2.2.1
This table include expansion configuration to the DS1 physical port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortDs1CnfgEntry

atmSuPortDs1CnfgEntry 1.3.6.1.4.1.164.12.4.2.2.1.1
the entries at this table describes the configuration of the agent physical.
OBJECT-TYPE    
  AtmSuPortDs1CnfgEntry  

atmSuPortDs1CnfgRxSensitivity 1.3.6.1.4.1.164.12.4.2.2.1.1.1
This attribute is the rx line sensetivity parameter used only for T1/CSU and E1/LTU interfaces.
OBJECT-TYPE    
  INTEGER s12dB(1), s30dB(2), s36dB(3), s15dB(4), s43dB(5)  

atmSuPortDs1CnfgLBO 1.3.6.1.4.1.164.12.4.2.2.1.1.2
This attribute is the line-Build-Out indicates sensitivity of the DS1 interface. The user can define if the agent will be CSU or DSU (for T1 only) by choosing the right option. On E1 interface this is done by hardware, so this parameter cannot be written.
OBJECT-TYPE    
  INTEGER txGain0db(1), txGain7dot5db(2), txGain15db(3), txGain22dot5db(4), len0p133ft(5), len133p266ft(6), len266p399ft(7), len399p533ft(8), len533p655ft(9), unbalanceE1(10), balanceE1(11)  

atmSuPortDs1CnfgRestoreTime 1.3.6.1.4.1.164.12.4.2.2.1.1.3
Determines the time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface.
OBJECT-TYPE    
  INTEGER ccittE1(1), restoreT1secFast(2), restoreT10sec62411(3)  

atmSuPortDs1CnfgInbandMng 1.3.6.1.4.1.164.12.4.2.2.1.1.4
A unique number to identify type of inband management over the link. For LA-104 and IMXi4, only one port may be used for inband management
OBJECT-TYPE    
  INTEGER off(2), dedicatedTs(4), dedicatedFr(6)  

atmSuPortDs1CnfgDedicatedTs 1.3.6.1.4.1.164.12.4.2.2.1.1.5
A unique number to identify Dedicated Time Slot for inband management of the T1/E1 port. It is applicable only when atmSuPortDs1CnfgInbandMng selected is not off. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid.
OBJECT-TYPE    
  Integer32  

atmSuPortDs1CbrCnfgTable 1.3.6.1.4.1.164.12.4.2.2.2
This table include expansion configuration to the DS1 physical port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortDs1CbrCnfgEntry

atmSuPortDs1CbrCnfgEntry 1.3.6.1.4.1.164.12.4.2.2.2.1
the entries at this table describes the configuration of the agent physical.
OBJECT-TYPE    
  AtmSuPortDs1CbrCnfgEntry  

atmSuPortDs1CbrIdleCode 1.3.6.1.4.1.164.12.4.2.2.2.1.1
An Idle code which sent on unused time-slots at CBR port .
OBJECT-TYPE    
  Integer32  

atmSuPortDs1CbrRxTimeSlots 1.3.6.1.4.1.164.12.4.2.2.2.1.2
This value indicates the time-slots used by the port for receiving. It uses 32 bits ( in 4 bytes octet string ) for E1 and low 24 bits for T1. each bit represents a time slot for receiving : time-slot 0 = bit 0 (LSB - most right bit in last byte), ... ... time-slot 31 = bit 31 (MSB - most left bit in first byte ). value '0' indicate unused time-slot and value '1' indicates used time-slot. note : time-slots '0' and '16' are used for signalling in E1 interface.
OBJECT-TYPE    
  TimeSlots  

atmSuPortDs1CbrTxTimeSlots 1.3.6.1.4.1.164.12.4.2.2.2.1.3
This value indicates the time-slots used by the port for transmiting. It uses 32 bits for E1 and low 24 bits for T1. each bit represents a time slot for transmiting : time-slot 0 = bit 0 (LSB - most right bit in last byte), ... ... time-slot 31 = bit 31 (MSB - most left bit in first byte ). value '0' indicate unused time-slot and value '1' indicates used time-slot. note : time-slots '0' and '16' are used for signalling in E1 interface.
OBJECT-TYPE    
  TimeSlots  

atmSuPortDs1CbrMaxNoOfConns 1.3.6.1.4.1.164.12.4.2.2.2.1.4
this object indicates the maximum number of cross-connect connections allowed beetween the ATM port and the CBR Port identified by IfIndex.
OBJECT-TYPE    
  Integer32  

atmSuPortDs1CbrConfNoOfConns 1.3.6.1.4.1.164.12.4.2.2.2.1.5
this object indicates the configured number of cross-connect connections exist beetween the ATM port and the CBR Port identified by IfIndex.
OBJECT-TYPE    
  Integer32  

atmSuPortDs1CbrSignallingSampleTime 1.3.6.1.4.1.164.12.4.2.2.2.1.6
determines how often the signalling of the DBCES connections are sampled and thier activity determined.
OBJECT-TYPE    
  INTEGER msec100(1), msec200(2), msec500(3), msec1000(4), msec1500(5), msec2000(6)  

atmSuPortAtm 1.3.6.1.4.1.164.12.4.2.3
OBJECT IDENTIFIER    

atmSuPortAtmCnfgTable 1.3.6.1.4.1.164.12.4.2.3.1
This table contains global configuration to the ATM port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortAtmCnfgEntry

atmSuPortAtmCnfgEntry 1.3.6.1.4.1.164.12.4.2.3.1.1
This object contains information about agent ATM configuration.
OBJECT-TYPE    
  AtmSuPortAtmCnfgEntry  

atmSuPortAtmCnfgIdleCellCLP 1.3.6.1.4.1.164.12.4.2.3.1.1.1
Determines the clp bit value for transmition in empty time slots.
OBJECT-TYPE    
  INTEGER clp0(1), clp1(2)  

atmSuPortAtmCnfgScramble 1.3.6.1.4.1.164.12.4.2.3.1.1.2
Determined by the standards if the cell will be scrambled or not.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

atmSuPortAtmSNMPVpi 1.3.6.1.4.1.164.12.4.2.3.1.1.3
The Vcc Vpi for SNMP requests.
OBJECT-TYPE    
  Integer32  

atmSuPortAtmSNMPVci 1.3.6.1.4.1.164.12.4.2.3.1.1.4
The Vcc Vci for SNMP requests.
OBJECT-TYPE    
  Integer32  

atmSuPortAtmSNMPStatus 1.3.6.1.4.1.164.12.4.2.3.1.1.5
value indicates if the SNMP Vcc is available for management.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

atmSuPortAtmILMIStatus 1.3.6.1.4.1.164.12.4.2.3.1.1.6
Value indicates if agent should respond to ILMI requests from the Atm switch or forward it. note: when using Atm to Frame-Relay configuration this value should be active to support ILMI. when using Atm-AtmDxi configuration the ILMI requests should be moved forward to the DTE or may be answered by the DCE.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

atmSuPortAtmSNMPIp 1.3.6.1.4.1.164.12.4.2.3.1.1.7
The interface IP address for SNMP requests.
OBJECT-TYPE    
  IpAddress  

atmSuPortAtmCnfgCDVOptimization 1.3.6.1.4.1.164.12.4.2.3.1.1.8
value indicates if optimization of CDV (Cell Delay Varation) is enbabled.
OBJECT-TYPE    
  INTEGER notApplicable(1), disable(2), enable(3)  

atmSuPortAtmCnfgShapingMode 1.3.6.1.4.1.164.12.4.2.3.1.1.9
ATM Shaping mode. Three possible values: SW Shaping. HW Shaping - APC with NCITS = 1. HW Shaping - APC with NCITS = 2 The difference between the two hardware modes is in the connection cell granularity and maximum bandwidth (BW): * For NCITS=1, the granularity is of one cell and the max. BW is the uplink BW, * For NCITS=2, the granularity is of every two cells and the max. BW is half of the uplink BW.
OBJECT-TYPE    
  INTEGER notApplicable(1), sw(2), hwNcits1(3), hwNcits2(4)  

atmSuPortAtmSNMPTrafficDescrIndex 1.3.6.1.4.1.164.12.4.2.3.1.1.10
The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VCL.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

atmSuPortAtmIfStatsTable 1.3.6.1.4.1.164.12.4.2.3.2
The table contains additional statistics information about the ATM interface.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortAtmIfStatsEntry

atmSuPortAtmIfStatsEntry 1.3.6.1.4.1.164.12.4.2.3.2.1
An entry in the ATM Interface statistics table.
OBJECT-TYPE    
  AtmSuPortAtmIfStatsEntry  

atmSuPortAtmRxClp0Cells 1.3.6.1.4.1.164.12.4.2.3.2.1.1
The number of cells received with correct HECs and CLP=0 and not misrouted
OBJECT-TYPE    
  Counter32  

atmSuPortAtmRxClp1Cells 1.3.6.1.4.1.164.12.4.2.3.2.1.2
The number of cells received with correct HEC's and CLP=1 and not misrouted.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmRxEfciSetCells 1.3.6.1.4.1.164.12.4.2.3.2.1.3
The number of cells received with EFCI bit set by the Agent
OBJECT-TYPE    
  Counter32  

atmSuPortAtmRxOamCells 1.3.6.1.4.1.164.12.4.2.3.2.1.4
The number of OAM cells received with correct HECs.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmTxClp0Cells 1.3.6.1.4.1.164.12.4.2.3.2.1.5
The number of cells transmitted with CLP=0.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmTxClp1Cells 1.3.6.1.4.1.164.12.4.2.3.2.1.6
The number of cells transmitted with CLP=1.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmTxEfciSetCells 1.3.6.1.4.1.164.12.4.2.3.2.1.7
The number of cells transmitted with EFCI bit set by the Agent
OBJECT-TYPE    
  Counter32  

atmSuPortAtmTxOamCells 1.3.6.1.4.1.164.12.4.2.3.2.1.8
The number of transmitted OAM cells.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTable 1.3.6.1.4.1.164.12.4.2.3.3
The table contains additional information about the ATM Vcl end points.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortAtmVclStatsEntry

atmSuPortAtmVclStatsEntry 1.3.6.1.4.1.164.12.4.2.3.3.1
An entry in the ATM Vcl statistics table.
OBJECT-TYPE    
  AtmSuPortAtmVclStatsEntry  

atmSuPortAtmVclStatsRxCells 1.3.6.1.4.1.164.12.4.2.3.3.1.1
The total number of cells received with correct HEC's.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxClp0Cells 1.3.6.1.4.1.164.12.4.2.3.3.1.2
The number of cells received with correct HEC's and CLP=0.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxClp1Cells 1.3.6.1.4.1.164.12.4.2.3.3.1.3
The number of cells received with correct HEC's and CLP=1.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxDiscardsCells 1.3.6.1.4.1.164.12.4.2.3.3.1.4
The number of cells, in ingress direction, discarded due to policing violation.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxCells 1.3.6.1.4.1.164.12.4.2.3.3.1.5
The total number of cells transmitted.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxClp0Cells 1.3.6.1.4.1.164.12.4.2.3.3.1.6
The number of cells transmitted with CLP=0.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxClp1Cells 1.3.6.1.4.1.164.12.4.2.3.3.1.7
The number of cells transmitted with CLP=1.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxTotalAISCells 1.3.6.1.4.1.164.12.4.2.3.3.1.8
Total number of AIS cells received on the VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxTotalCCCells 1.3.6.1.4.1.164.12.4.2.3.3.1.9
Total number of Continuity Check cells that were received on the VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTotalSuccLoopbacks 1.3.6.1.4.1.164.12.4.2.3.3.1.10
Total number of loopbacks that were requested by the ACE20 and for which there was a response (not supported).
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTotalFailLoopbacks 1.3.6.1.4.1.164.12.4.2.3.3.1.11
Total number of loopbacks that were requested by the ACE20 and for which there was no response (not supported).
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxTotalRDICells 1.3.6.1.4.1.164.12.4.2.3.3.1.12
Total number of RDI cells received on a VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTotalLOCSeconds 1.3.6.1.4.1.164.12.4.2.3.3.1.13
Total number of seconds during which there was loss of continuity on the VC - no data and no continuity check cells were received on the VC whilst it was in 'sink' continuity check mode.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxTotalLoopbackRequests 1.3.6.1.4.1.164.12.4.2.3.3.1.14
Total number of loopback requests received by the ACE20 on a VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxTotalAISCells 1.3.6.1.4.1.164.12.4.2.3.3.1.15
Total number of AIS cells that were transmitted on a VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxTotalCCCells 1.3.6.1.4.1.164.12.4.2.3.3.1.16
Total number of continuity check cells that were transmitted on a VC (when there is no data cells and the connection is in 'source' continuity check mode).
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxTotalRDICells 1.3.6.1.4.1.164.12.4.2.3.3.1.17
Total number of RDI cells transmitted on a VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxTotalLoopbackResponses 1.3.6.1.4.1.164.12.4.2.3.3.1.18
Total number of loopback responses that were transmitted as a result of loopback requests received.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsTxTotalLoopbackRequests 1.3.6.1.4.1.164.12.4.2.3.3.1.19
Total number of loopback requests that were transmitted by the ACE20 on a VC.
OBJECT-TYPE    
  Counter32  

atmSuPortAtmVclStatsRxTotalLoopbackResponses 1.3.6.1.4.1.164.12.4.2.3.3.1.20
Total number of loopback responses that were received as a result of loopback transmitted by the ACE20.
OBJECT-TYPE    
  Counter32  

atmSuPortFr 1.3.6.1.4.1.164.12.4.2.4
OBJECT IDENTIFIER    

atmSuPortFrLportTable 1.3.6.1.4.1.164.12.4.2.4.1
The table Contains configuration parameters of the Frame-Relay port and has expansion to frLportTable in RFC1604 MIB.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortFrLportEntry

atmSuPortFrLportEntry 1.3.6.1.4.1.164.12.4.2.4.1.1
An entry in the Frame Relay Logical Port Information table.
OBJECT-TYPE    
  AtmSuPortFrLportEntry  

atmSuPortFrLportSNMPDlci 1.3.6.1.4.1.164.12.4.2.4.1.1.1
The SNMP Dlci of this entry.
OBJECT-TYPE    
  Integer32  

atmSuPortFrLportSNMPStatus 1.3.6.1.4.1.164.12.4.2.4.1.1.2
value indicates if SNMP over FR is available for management.
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

atmSuPortFrLportVCSigProtocol 1.3.6.1.4.1.164.12.4.2.4.1.1.3
The value of this object identifies the Local In-Channel Signaling Protocol that is used for this frame relay UNI/NNI logical port.
OBJECT-TYPE    
  INTEGER none(1), ccittQ933A(2), ansiT1617D(3), lmi(4)  

atmSuPortFrLportVCSigProcedure 1.3.6.1.4.1.164.12.4.2.4.1.1.4
The value of this object identifies the Local In-Channel Signaling Procedure that is used for this UNI/NNI logical port. The UNI/NNI logical port can be performing user-to-network network-side and user-to-network user-side procedures or bidirectional procedures. this parameter gets value 'notApplicable when the VCSigProtocol is none
OBJECT-TYPE    
  INTEGER notApplicable(1), u2nnet(2), u2nuser(3), bidirect(4)  

atmSuPortFrLportCLLM 1.3.6.1.4.1.164.12.4.2.4.1.1.5
indicate if the configuration is supporting CLLM ( Consolidated Link Layer Management ) .
OBJECT-TYPE    
  INTEGER active(1), notActive(2)  

atmSuPortFrLportSNMPIp 1.3.6.1.4.1.164.12.4.2.4.1.1.6
The interface IP address of this entry.
OBJECT-TYPE    
  IpAddress  

atmSuPortFrPvcEndptTable 1.3.6.1.4.1.164.12.4.2.4.2
The table contains additional information about the Frame Relay end point.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortFrPvcEndptEntry

atmSuPortFrPvcEndptEntry 1.3.6.1.4.1.164.12.4.2.4.2.1
An entry for FR end-point statistics ( expansion to RFC 1604 ).
OBJECT-TYPE    
  AtmSuPortFrPvcEndptEntry  

atmSuPortFrPvcEndptTxFECNs 1.3.6.1.4.1.164.12.4.2.4.2.1.1
number of frames transmited with FECN ( Forward Explicit Congestion Notification ).
OBJECT-TYPE    
  Counter32  

atmSuPortFrPvcEndptTxBECNs 1.3.6.1.4.1.164.12.4.2.4.2.1.2
number of frames transmited with BECN ( Backward Explicit Congestion Notification ).
OBJECT-TYPE    
  Counter32  

atmSuPortFrPvcEndptTxDEs 1.3.6.1.4.1.164.12.4.2.4.2.1.3
number of frames transmited with the DE ( Discarded Eligible ) bit set.
OBJECT-TYPE    
  Counter32  

atmSuPortFrPvcEndptRxFECNs 1.3.6.1.4.1.164.12.4.2.4.2.1.4
number of frames received with FECN ( Forward Explicit Congestion Notification ).
OBJECT-TYPE    
  Counter32  

atmSuPortFrPvcEndptRxBECNs 1.3.6.1.4.1.164.12.4.2.4.2.1.5
number of frames received with BECN ( Backward Explicit Congestion Notification ).
OBJECT-TYPE    
  Counter32  

atmSuPortDxi 1.3.6.1.4.1.164.12.4.2.5
OBJECT IDENTIFIER    

atmSuPortDxiConfTable 1.3.6.1.4.1.164.12.4.2.5.1
This table contains ATM-DXI managment address (DFA) ending at the local agent. only LMI managment supported for ATM-DXI.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortDxiConfEntry

atmSuPortDxiConfEntry 1.3.6.1.4.1.164.12.4.2.5.1.1
This object contains information about agent Dxi interface.
OBJECT-TYPE    
  AtmSuPortDxiConfEntry  

atmSuPortDxiPortMode 1.3.6.1.4.1.164.12.4.2.5.1.1.1
This object identifies the dxi mode being used by the atm dxi port.
OBJECT-TYPE    
  INTEGER mode1a(1), mode1b(2), mode2(3)  

atmSuPortDxiSigProtocol 1.3.6.1.4.1.164.12.4.2.5.1.1.2
This value indicates if we using LMI signalling protocol or not using any signalling .
OBJECT-TYPE    
  INTEGER none(1), lmi(2)  

atmSuPortDxiSigDfa 1.3.6.1.4.1.164.12.4.2.5.1.1.3
The Signalling Dfa address . the default LMI Dfa defined for LMI by the AtmForum is 0.
OBJECT-TYPE    
  Integer32  

atmSuPortCmdTable 1.3.6.1.4.1.164.12.4.2.6
General commands to be done on agent's ports.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortCmdEntry

atmSuPortCmdEntry 1.3.6.1.4.1.164.12.4.2.6.1
This object contains entry information.
OBJECT-TYPE    
  AtmSuPortCmdEntry  

atmSuResetPortStatsCmd 1.3.6.1.4.1.164.12.4.2.6.1.1
reset statistics of port.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

atmSuResetConnsStatsCmd 1.3.6.1.4.1.164.12.4.2.6.1.2
reset statistics of all cross connections attached to this port. set-request is allowed only on the DATA Ports . for get-request value is always 'off'
OBJECT-TYPE    
  INTEGER off(1), on(2)  

atmSuPortEther 1.3.6.1.4.1.164.12.4.2.7
OBJECT IDENTIFIER    

atmSuPortEtherTable 1.3.6.1.4.1.164.12.4.2.7.1
The table Contains configuration parameters of the Ethernet port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmSuPortEtherEntry

atmSuPortEtherEntry 1.3.6.1.4.1.164.12.4.2.7.1.1
An entry in the Ethernet Port Information table.
OBJECT-TYPE    
  AtmSuPortEtherEntry  

atmSuPortEtherIP 1.3.6.1.4.1.164.12.4.2.7.1.1.1
The interface IP address for SNMP requests.
OBJECT-TYPE    
  IpAddress  

atmSuPortEtherMask 1.3.6.1.4.1.164.12.4.2.7.1.1.2
The interface IP address mask for SNMP requests.
OBJECT-TYPE    
  IpAddress  

atmSuPortEtherDefaultGateWayIp 1.3.6.1.4.1.164.12.4.2.7.1.1.3
The Ethernet bridge default gateway IP address.
OBJECT-TYPE    
  IpAddress  

atmSuPortEtherDefaultCrossConnectId 1.3.6.1.4.1.164.12.4.2.7.1.1.4
Default Cross Connect Id.
OBJECT-TYPE    
  Integer32  

atmSuPortEtherDefaultGatewayStatus 1.3.6.1.4.1.164.12.4.2.7.1.1.5
Default Gateway Status.
OBJECT-TYPE    
  INTEGER active(1), notActive(2), notApplicable(255)  

atmSuPortEtherSNMPStatus 1.3.6.1.4.1.164.12.4.2.7.1.1.6
The value indicates if the SNMP of Ethernet bridge interface is available for management.
OBJECT-TYPE    
  INTEGER active(1), notActive(2), notApplicable(255)  

atmSuPortEtherFragmentation 1.3.6.1.4.1.164.12.4.2.7.1.1.7
Fragmentation. When application is not router value must be 'notApplicable'.
OBJECT-TYPE    
  INTEGER no(2), yes(3), notApplicable(255)  

atmSuPortEtherRIPMode 1.3.6.1.4.1.164.12.4.2.7.1.1.8
RIP Mode. When application is not router value must be 'notApplicable'.
OBJECT-TYPE    
  INTEGER rip1(1), rip2(2), rip1And2(3), none(4), notApplicable(255)  

atmSuPortEtherBridgingMode 1.3.6.1.4.1.164.12.4.2.7.1.1.9
Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs. When application is router value must be 'notApplicable'.
OBJECT-TYPE    
  INTEGER accessOnly(1), accessAndSwitching(2), notApplicable(255)  

atmSuPortEtherARPTimeout 1.3.6.1.4.1.164.12.4.2.7.1.1.10
ARP Timeout. When application is not router or when this object is not applicable, value must be 0.
OBJECT-TYPE    
  Integer32 0..10  

atmSuPortEtherAgingTime 1.3.6.1.4.1.164.12.4.2.7.1.1.11
The timeout period in seconds for aging out stored information. valid values are 10...1000000. The value of (0) has the special meaning - not applicable.
OBJECT-TYPE    
  Integer32 0..1000000  

atmSuPortEtherPppOEEnable 1.3.6.1.4.1.164.12.4.2.7.1.1.12
Enable or Disable transparent PPP over ethernet bridge. When PPP over Ethernet is enabled, non PPP traffic is blocked by the bridge.
OBJECT-TYPE    
  INTEGER notApplicable(1), off(2), on(3)  

atmSuPortEtherStatus 1.3.6.1.4.1.164.12.4.2.7.1.1.13
This object allows user to add/remove entries to/from this table. It will be supported only by certain devices. destroy - may not be possible for certain interfaces.
OBJECT-TYPE    
  INTEGER active(1), createAndGo(4), destroy(6)  

atmSuCrossConnect 1.3.6.1.4.1.164.12.4.3
OBJECT IDENTIFIER    

atmSuCrossConnectAtmFr 1.3.6.1.4.1.164.12.4.3.1
OBJECT IDENTIFIER    

atmSuCrossConnectAtmFrDescriptor 1.3.6.1.4.1.164.12.4.3.1.1
OBJECT IDENTIFIER    

atmFrCrossConnectNetwork 1.3.6.1.4.1.164.12.4.3.1.1.1
OBJECT IDENTIFIER    

atmFrCrossConnectService 1.3.6.1.4.1.164.12.4.3.1.1.2
OBJECT IDENTIFIER    

atmFrDescrTable 1.3.6.1.4.1.164.12.4.3.1.2
This table contains information on ATM to FR Connection descriptor types, and their associated parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmFrDescrEntry

atmFrDescrEntry 1.3.6.1.4.1.164.12.4.3.1.2.1
This list contains ATM to FR Connection descriptor type, and its associated parameters.
OBJECT-TYPE    
  AtmFrDescrEntry  

atmFrDescrIndex 1.3.6.1.4.1.164.12.4.3.1.2.1.1
This object is used to identify the row index of the ATM to FR connection descriptor table.
OBJECT-TYPE    
  Integer32  

atmFrDescrType 1.3.6.1.4.1.164.12.4.3.1.2.1.2
The value of this object identifies the type of the ATM to FR Connection descriptor. The type may indicate Network connection descriptor or a Service connection descriptor with one or more parameters. These parameters are specified as a parameter vector, in the corresponding instances of the objects: atmFrDescrClp2De atmFrDescrDe2Clp atmFrDescrFecn2Efci atmFrDescrMappingMode.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

atmFrDescrClp2De 1.3.6.1.4.1.164.12.4.3.1.2.1.3
The first parameter of the ATM to FR Connection descriptor used according to the value of atmFrDescrType.
OBJECT-TYPE    
  INTEGER convSscs(1), conv(2), always0(3), always1(4)  

atmFrDescrDe2Clp 1.3.6.1.4.1.164.12.4.3.1.2.1.4
The second parameter of the ATM to FR Connection descriptor used according to the value of atmFrDescrType.
OBJECT-TYPE    
  INTEGER conv(1), always0(2), always1(3)  

atmFrDescrFecn2Efci 1.3.6.1.4.1.164.12.4.3.1.2.1.5
The third parameter of the ATM to FR Connection descriptor used according to the value of atmFrDescrType.
OBJECT-TYPE    
  INTEGER conv(1), always0(2)  

atmFrDescrMappingMode 1.3.6.1.4.1.164.12.4.3.1.2.1.6
The fourth parameter of the ATM to FR Connection descriptor used according to the value of atmFrDescrType.
OBJECT-TYPE    
  INTEGER transparent(1), translation(2)  

atmFrDescrRowStatus 1.3.6.1.4.1.164.12.4.3.1.2.1.7
This object is used to create, modify or delete a row in this table.
OBJECT-TYPE    
  RowStatus  

atmSuCrossConnectAtmFrIndexNext 1.3.6.1.4.1.164.12.4.3.1.3
This object contains an appropriate value to be used for atmFrCnfgCrossConnectIndex when creating entries in the atmFrCnfgTable. The value 0 indicates that no unassigned entries are available. To obtain the atmFrCnfgCrossConnectIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the mandatory value of this object. After each retrieval, the agent should modify the value to the next unassigned index.
OBJECT-TYPE    
  Integer32  

atmFrCnfgTable 1.3.6.1.4.1.164.12.4.3.1.4
This table defines virtual connections between ATM and Frame Relay endpoints.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmFrCnfgEntry

atmFrCnfgEntry 1.3.6.1.4.1.164.12.4.3.1.4.1
An entry defines virtual connection between ATM and Frame Relay endpoint.
OBJECT-TYPE    
  AtmFrCnfgEntry  

atmFrCnfgCrossConnectIndex 1.3.6.1.4.1.164.12.4.3.1.4.1.1
A unique value to identify this cross-connect.
OBJECT-TYPE    
  Integer32  

atmFrCnfgAtmIfIndex 1.3.6.1.4.1.164.12.4.3.1.4.1.2
The ifIndex associated to the ATM interface.
OBJECT-TYPE    
  Integer32  

atmFrCnfgAtmVpi 1.3.6.1.4.1.164.12.4.3.1.4.1.3
The Vpi number of the ATM end point.
OBJECT-TYPE    
  Integer32 1..4095  

atmFrCnfgAtmVci 1.3.6.1.4.1.164.12.4.3.1.4.1.4
The Vci number of the ATM end point.
OBJECT-TYPE    
  Integer32 0..65535  

atmFrCnfgFrIfIndex 1.3.6.1.4.1.164.12.4.3.1.4.1.5
The ifIndex associated to the Frame Relay interface.
OBJECT-TYPE    
  Integer32  

atmFrCnfgDlci 1.3.6.1.4.1.164.12.4.3.1.4.1.6
The DLCI number of the FR end point.
OBJECT-TYPE    
  Integer32  

atmFrCnfgAdminStatus 1.3.6.1.4.1.164.12.4.3.1.4.1.7
This object indicates the connection status requested by the user.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmFrCnfgOperStatus 1.3.6.1.4.1.164.12.4.3.1.4.1.8
This object indicates the Operational status of the connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmFrCnfgLastChange 1.3.6.1.4.1.164.12.4.3.1.4.1.9
The value of sysUpTime at the time the ATM to FR connection entered its mandatory operational state. If the mandatory state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
OBJECT-TYPE    
  TimeStamp  

atmFrCnfgMappingDescrIndex 1.3.6.1.4.1.164.12.4.3.1.4.1.10
The value of this object identifies the row in the atmFrDescrTable.
OBJECT-TYPE    
  Integer32  

atmFrCnfgSscsDlci 1.3.6.1.4.1.164.12.4.3.1.4.1.11
The DLCI number given to the SSCS Sub-layer for network interworking only ( the default value is 'atmFrCnfgDlci' ). for Service Interworking do not implement this variable.
OBJECT-TYPE    
  Integer32  

atmFrCnfgTrafficDescrIndex 1.3.6.1.4.1.164.12.4.3.1.4.1.12
The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VCL. note :setting this value is allowed only to point2point connections. for many2one connections is being set by the atmFrCrossConnectMany2OneRootsTable and this field is equal to this setting.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

atmFrCnfgPriority 1.3.6.1.4.1.164.12.4.3.1.4.1.13
This object define the priority of connection. The first parameter affects the transmition of cells in Conjested network is the bitRate( Cbr has the highest priority and then Vbr,Ubr ) In connections with the same bitRate this object will define the priority.
OBJECT-TYPE    
  INTEGER highPriority(1), mediumPriority(2), lowPriority(3)  

atmFrCnfgRowStatus 1.3.6.1.4.1.164.12.4.3.1.4.1.14
This object is used to create a new row or modify or delete an existing row in this table.
OBJECT-TYPE    
  RowStatus  

atmFrCnfgAllocatedBuffers 1.3.6.1.4.1.164.12.4.3.1.4.1.15
This object enables user to limit the amount of buffers used by the connection. The limit set by this object will give the effect of a virtual buffer pool per connection. The user can allocate between 10 to 217 buffers to every connection. By default the limit is 50 buffers. Sum of limits allocated to all connections must not exceed the total amount of available buffers. Whenever a connection exceeds it's buffer limit due to congestion or burst - traffic is discarded
OBJECT-TYPE    
  Integer32 10..217  

atmFrMaxMany2OneConnsPerVcc 1.3.6.1.4.1.164.12.4.3.1.5
The Maximum Number of many2one cross-connect connections allowed per Vcc .
OBJECT-TYPE    
  Integer32  

atmSuCrossConnectAtmDxi 1.3.6.1.4.1.164.12.4.3.2
OBJECT IDENTIFIER    

atmSuCrossConnectAtmDxiIndexNext 1.3.6.1.4.1.164.12.4.3.2.1
This object contains an appropriate value to be used for atmDxiCnfgCrossConnectIndex when creating entries in the atmDxiCnfgTable. The value 0 indicates that no unassigned entries are available. To obtain the atmDxiCnfgCrossConnectIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the mandatory value of this object. After each retrieval, the agent should modify the value to the next unassigned index.
OBJECT-TYPE    
  Integer32  

atmDxiCnfgTable 1.3.6.1.4.1.164.12.4.3.2.2
This table defines virtual connections between ATM and ATM-DXI endpoints.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmDxiCnfgEntry

atmDxiCnfgEntry 1.3.6.1.4.1.164.12.4.3.2.2.1
An entry defines virtual connection between ATM and ATM-DXI endpoint.
OBJECT-TYPE    
  AtmDxiCnfgEntry  

atmDxiCnfgCrossConnectIndex 1.3.6.1.4.1.164.12.4.3.2.2.1.1
A unique value to identify this cross-connect.
OBJECT-TYPE    
  Integer32  

atmDxiCnfgAtmIfIndex 1.3.6.1.4.1.164.12.4.3.2.2.1.2
The ifIndex associated to the ATM interface.
OBJECT-TYPE    
  Integer32  

atmDxiCnfgAtmVpi 1.3.6.1.4.1.164.12.4.3.2.2.1.3
The Vpi number of the ATM end point.
OBJECT-TYPE    
  Integer32 1..4095  

atmDxiCnfgAtmVci 1.3.6.1.4.1.164.12.4.3.2.2.1.4
The Vci number of the ATM end point.
OBJECT-TYPE    
  Integer32 0..65535  

atmDxiCnfgDxiIfIndex 1.3.6.1.4.1.164.12.4.3.2.2.1.5
The ifIndex associated to the atm-dxi interface.
OBJECT-TYPE    
  Integer32  

atmDxiCnfgDfa 1.3.6.1.4.1.164.12.4.3.2.2.1.6
The DFA number of the DXI end point.
OBJECT-TYPE    
  Integer32  

atmDxiCnfgAdminStatus 1.3.6.1.4.1.164.12.4.3.2.2.1.7
The requested state of the ATM to DXI connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmDxiCnfgOperStatus 1.3.6.1.4.1.164.12.4.3.2.2.1.8
The real operational status of the ATM to DXI connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmDxiCnfgLastChange 1.3.6.1.4.1.164.12.4.3.2.2.1.9
The value of sysUpTime at the time the ATM to DXI connection entered its mandatory operational state. If the mandatory state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. Same value define both direction ( Atm2Dxi and Dxi2Atm ).
OBJECT-TYPE    
  TimeStamp  

atmDxiCnfgTrafficDescrIndex 1.3.6.1.4.1.164.12.4.3.2.2.1.10
The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VCL.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

atmDxiCnfgPriority 1.3.6.1.4.1.164.12.4.3.2.2.1.11
This object define the priority of connection. The first parameter affects the transmition of cells in Conjested network is the bitRate( Cbr has the highest priority and then Vbr,Ubr ) In connections with the same bitRate this object will define the priority.
OBJECT-TYPE    
  INTEGER highPriority(1), mediumPriority(2), lowPriority(3)  

atmDxiCnfgRowStatus 1.3.6.1.4.1.164.12.4.3.2.2.1.12
This object is used to create a new row or modify or delete an existing row in this table.
OBJECT-TYPE    
  RowStatus  

atmSuAtmCbr 1.3.6.1.4.1.164.12.4.3.3
OBJECT IDENTIFIER    

atmCbrCnfgTable 1.3.6.1.4.1.164.12.4.3.3.1
This table defines AAL1 virtual connections (not CES) between ATM port and DS1-CBR port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmCbrCnfgEntry

atmCbrCnfgEntry 1.3.6.1.4.1.164.12.4.3.3.1.1
An entry defines virtual connection between ATM port and DS1-CBR port.
OBJECT-TYPE    
  AtmCbrCnfgEntry  

atmCbrCnfgAtmIfIndex 1.3.6.1.4.1.164.12.4.3.3.1.1.1
The ifIndex associated to the ATM interface.
OBJECT-TYPE    
  Integer32  

atmCbrCnfgAtmVpi 1.3.6.1.4.1.164.12.4.3.3.1.1.2
The Vpi number of the ATM end point.
OBJECT-TYPE    
  Integer32 1..4095  

atmCbrCnfgAtmVci 1.3.6.1.4.1.164.12.4.3.3.1.1.3
The Vci number of the ATM end point.
OBJECT-TYPE    
  Integer32 0..65535  

atmCbrCnfgCbrIfIndex 1.3.6.1.4.1.164.12.4.3.3.1.1.4
The ifIndex associated to the logical interface of DS0s bundle or to ifIndex of one of the data ports.
OBJECT-TYPE    
  Integer32  

atmCbrCnfgAdminStatus 1.3.6.1.4.1.164.12.4.3.3.1.1.5
The requested status of the connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmCbrCnfgOperStatus 1.3.6.1.4.1.164.12.4.3.3.1.1.6
The real operational status of the connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmCbrCnfgLastChange 1.3.6.1.4.1.164.12.4.3.3.1.1.7
The value of sysUpTime at the time the ATM to CBR connection entered its mandatory operational state. If the mandatory state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. Same value define both direction ( Atm2Cbr and Cbr2Atm ).
OBJECT-TYPE    
  TimeStamp  

atmCbrCnfgAAL1Signalling 1.3.6.1.4.1.164.12.4.3.3.1.1.8
Not in use. Must be always 'off'.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

atmCbrCnfgRxTimeSlots 1.3.6.1.4.1.164.12.4.3.3.1.1.9
This value indicates the time-slots used by this connection for receiving. It uses 32 bits for E1 and low 24 bits for T1. each bit represents a time slot for receiving : time-slot 0 = bit 0 (LSB - most right bit in last byte), ... ... time-slot 31 = bit 31 (MSB - most left bit in first byte ). value '0' indicate unused time-slot and value '1' indicates used time-slot. On set-request the user indicates the time-slot he needs for requested ATM-Vcc by putting '1' to the right bits. note : time-slots '0' and '16' are used for signalling in E1 interface. Currently not in use. Must be '0'.
OBJECT-TYPE    
  TimeSlots  

atmCbrCnfgRxBytesPerCell 1.3.6.1.4.1.164.12.4.3.3.1.1.10
number of bytes to be receive in order per cell to low the delay.
OBJECT-TYPE    
  Integer32  

atmCbrCnfgTxTimeSlots 1.3.6.1.4.1.164.12.4.3.3.1.1.11
This value indicates the time-slots used by this connection for receiving. It uses 32 bits for E1 and low 24 bits for T1. each bit represents a time slot for receiving : time-slot 0 = bit 0 (LSB - most right bit in last byte), ... ... time-slot 31 = bit 31 (MSB - most left bit in first byte ). value '0' indicate unused time-slot and value '1' indicates used time-slot. On set-request the user indicates the time-slot he needs for requested ATM-Vcc by putting '1' to the right bits. note : time-slots '0' and '16' are used for signalling in E1 interface. Currently not in use. Must be '0'.
OBJECT-TYPE    
  TimeSlots  

atmCbrCnfgTxBytesPerCell 1.3.6.1.4.1.164.12.4.3.3.1.1.12
number of bytes to be transmit in order per cell to low the delay.
OBJECT-TYPE    
  Integer32  

atmCbrCnfgParity 1.3.6.1.4.1.164.12.4.3.3.1.1.13
Controls the use of pointer parity when using the STRUCTURED or STRUCTURED WITH POINTER connection type. as defined by atmCbrCnfgService. ON - Pointer parity bit generation at the transmit side, and checking of parity bit for error detection at the receiving side enabled. Supported only for STRUCTURED or STRUCTURED WITH POINTER service. OFF - Pointer parity generation and checking disabled. Supported only for STRUCTURED or STRUCTURED WITH POINTER service. N/A - Not applicable. This is the only option when selecting UNSTRUCTURED or STRUCTURED WITHOUT POINTER.
OBJECT-TYPE    
  INTEGER off(1), on(2), notApplicable(3)  

atmCbrCnfgRowStatus 1.3.6.1.4.1.164.12.4.3.3.1.1.14
This object is used to create a new row or modify or delete an existing row in this table.
OBJECT-TYPE    
  RowStatus  

atmCbrCnfgService 1.3.6.1.4.1.164.12.4.3.3.1.1.15
Define if DSx service is structured or unstructured. A structured(3) interface is some nx64Kbps. (n x DS0 = n Time Slots) An unstructured (2) interface is full DSx, x >0. (1.544Mbps, 2.048Mbps, 6.312Mbps, 44.736 Mbps, or 34.368 Mbps.) This objects selects the connection type also for AAL1 Stream for Data port. The available selections depend on the data rate selected. For the 64 kbps rate: STRUCTURED WITH POINTER = structure(4) Use of the structured service as defined in ATMF AF-VTOA-0078.000. STRUCTURED WITHOUT POINTER : same as above, but without using a pointer (the resulting cell structure is similar to that of the unstructured service cells). Default: STRUCTURED WITH POINTER structuredControlSignalsTransport -Pointer is used to transfer Data Control Signals through ATM network. For other rates: STRUCTURED : Use of structured service as defined in ATMF AF-VTOA-0078.000. UNSTRUCTURED : Use of unstructured service as defined in ATMF document AF-VTOA-0078.000.
OBJECT-TYPE    
  INTEGER notApplicable(1), unstructured(2), structured(3), structuredWithPointer(4), structuredWithoutPointer(5), structuredControlSignalsTransport(6)  

atmCESConfExtnsTable 1.3.6.1.4.1.164.12.4.3.3.2
This table defines virtual connections between ATM port and DS1-CBR port.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmCESConfExtnsEntry

atmCESConfExtnsEntry 1.3.6.1.4.1.164.12.4.3.3.2.1
An entry defines virtual connection between ATM port and DS1-CBR port.
OBJECT-TYPE    
  AtmCESConfExtnsEntry  

atmCESLastChange 1.3.6.1.4.1.164.12.4.3.3.2.1.1
The value of sysUpTime at the time the ATM to CBR connection entered its mandatory operational state. If the mandatory state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.
OBJECT-TYPE    
  TimeStamp  

atmCESRxBytesPerCell 1.3.6.1.4.1.164.12.4.3.3.2.1.2
Number of bytes to be received per cell, in order to decrease the delay.
OBJECT-TYPE    
  Integer32 1..47  

atmCESTxBytesPerCell 1.3.6.1.4.1.164.12.4.3.3.2.1.3
Number of bytes to be transmitted per cell, in order to decrease the delay.
OBJECT-TYPE    
  Integer32 1..47  

atmCESAal1Type 1.3.6.1.4.1.164.12.4.3.3.2.1.4
Type of CBR connection: CES , DBCES or transparent .
OBJECT-TYPE    
  INTEGER ces(1), dbces(2), transparent(3)  

atmCESParity 1.3.6.1.4.1.164.12.4.3.3.2.1.5
Indicate if we'll add even parity to the pointer of the structure of CES.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

atmCESSigType 1.3.6.1.4.1.164.12.4.3.3.2.1.6
type of signalling for a DBCES connection. Must be 'other' for CES connection.
OBJECT-TYPE    
  INTEGER eAndmOrPlar(1), fxoLoopStart(2), fxsLoopStart(3), fxoGroundStart(4), fxsGroundStart(5), r2(6), other(7)  

atmCESSigABBits 1.3.6.1.4.1.164.12.4.3.3.2.1.7
This attribute is applicable only when value of atmCESSigType is other. Represents the AB bits for Rx/Tx and their masks in this way: bits 7..6: Tx AB bits value, bits 5..4: Tx AB bits mask, bits 3..2: Rx AB bits value, bits 1..0: Rx AB bits mask. All bits must be 0 for CES connection.
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

atmSuCrossConnectAtmEther 1.3.6.1.4.1.164.12.4.3.4
OBJECT IDENTIFIER    

atmSuCrossConnectAtmEtherIndexNext 1.3.6.1.4.1.164.12.4.3.4.1
This object contains an appropriate value to be used for atmEtherCnfgCrossConnectIndex when creating entries in the atmEtherCnfgTable. The value 0 indicates that no unassigned entries are available. To obtain the atmEtherCnfgCrossConnectIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index.
OBJECT-TYPE    
  Integer32  

atmEtherCnfgTable 1.3.6.1.4.1.164.12.4.3.4.2
This table defines virtual connections between ATM and ATM-BridgedEthernet endpoints.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmEtherCnfgEntry

atmEtherCnfgEntry 1.3.6.1.4.1.164.12.4.3.4.2.1
An entry defines virtual connection between ATM and ATM-Ethernet endpoint.
OBJECT-TYPE    
  AtmEtherCnfgEntry  

atmEtherCnfgCrossConnectIndex 1.3.6.1.4.1.164.12.4.3.4.2.1.1
A unique value to identify this cross-connect.
OBJECT-TYPE    
  Integer32  

atmEtherCnfgAtmIfIndex 1.3.6.1.4.1.164.12.4.3.4.2.1.2
The ifIndex associated to the ATM interface.
OBJECT-TYPE    
  Integer32  

atmEtherCnfgAtmVpi 1.3.6.1.4.1.164.12.4.3.4.2.1.3
The Vpi number of the ATM end point.
OBJECT-TYPE    
  Integer32 1..4095  

atmEtherCnfgAtmVci 1.3.6.1.4.1.164.12.4.3.4.2.1.4
The Vci number of the ATM end point.
OBJECT-TYPE    
  Integer32 0..65535  

atmEtherCnfgEtherIfIndex 1.3.6.1.4.1.164.12.4.3.4.2.1.5
The ifIndex associated to the atm-Ethernet interface.
OBJECT-TYPE    
  Integer32  

atmEtherCnfgMacAddr 1.3.6.1.4.1.164.12.4.3.4.2.1.6
The DFA number of the Ethernet end point.
OBJECT-TYPE    
  MacAddress  

atmEtherCnfgAdminStatus 1.3.6.1.4.1.164.12.4.3.4.2.1.7
The requested state of the ATM to Ethernet connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmEtherCnfgOperStatus 1.3.6.1.4.1.164.12.4.3.4.2.1.8
The real operational status of the ATM to Ethernet connection.
OBJECT-TYPE    
  INTEGER up(1), down(2)  

atmEtherCnfgLastChange 1.3.6.1.4.1.164.12.4.3.4.2.1.9
The value of sysUpTime at the time the ATM to Ethernet connection entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. Same value define both direction ( Atm2Ether and Ether2Atm ).
OBJECT-TYPE    
  TimeStamp  

atmEtherCnfgTrafficDescrIndex 1.3.6.1.4.1.164.12.4.3.4.2.1.10
The value of this object identifies the row in the atmTrafficDescrParamTable which applies to the transmit direction of the VCL.
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

atmEtherCnfgEncapsulationMode 1.3.6.1.4.1.164.12.4.3.4.2.1.11
This object define the encapsulation type requested for the connection. it indicates if we transfer the Ethernet frame to the atm side without the Crc32- AtmBridgedEther, or with it - AtmBridgedEther-CRC.
OBJECT-TYPE    
  INTEGER atmBridgedEther(1), atmBridgedEtherCRC(2)  

atmEtherCnfgPriority 1.3.6.1.4.1.164.12.4.3.4.2.1.12
This object define the priority of connection. The first parameter affects the transmition of cells in Conjested network is the Service Category( Cbr has the highest priority and then Vbr,Ubr ) In connections with the same category this object will define the priority.
OBJECT-TYPE    
  INTEGER highPriority(1), mediumPriority(2), lowPriority(3)  

atmEtherCnfgRowStatus 1.3.6.1.4.1.164.12.4.3.4.2.1.13
This object is used to create a new row or modify or delete an existing row in this table.
OBJECT-TYPE    
  RowStatus  

atmEtherCnfgRouterIP 1.3.6.1.4.1.164.12.4.3.4.2.1.14
The interface IP address for SNMP requests.
OBJECT-TYPE    
  IpAddress  

atmEtherCnfgRouterMask 1.3.6.1.4.1.164.12.4.3.4.2.1.15
The interface IP address mask for SNMP requests.
OBJECT-TYPE    
  IpAddress  

atmEtherCnfgRouterFragmentation 1.3.6.1.4.1.164.12.4.3.4.2.1.16
Fragmentation. When application is not router value must be 'notApplicable'.
OBJECT-TYPE    
  INTEGER no(2), yes(3), notApplicable(255)  

atmEtherCnfgRouterRIPMode 1.3.6.1.4.1.164.12.4.3.4.2.1.17
RIP Mode. When application is not router value must be 'notApplicable'.
OBJECT-TYPE    
  INTEGER rip1(1), rip2(2), rip1And2(3), none(4), notApplicable(255)  

atmEtherCnfgRouterMTU 1.3.6.1.4.1.164.12.4.3.4.2.1.18
.
OBJECT-TYPE    
  Integer32  

atmEtherCnfgPPPEncapsulation 1.3.6.1.4.1.164.12.4.3.4.2.1.19
This object define the encapsulation type requested for the connection. rfc1483 - Multiprotocol Encapsulation over ATM Adaptation Layer 5 (no PPP) PPP VC Muxed - For VC Based Multiplexing, the carried network interconnect protocol is identified implicitly by the VC connecting the two ATM stations, i.e. each protocol must be carried over a separate VC. There is therefore no need to include explicit multiplexing information in the Payload of the AAL5 CPCS-PDU. This results in minimal bandwidth and processing overhead. PPP LLC Muxed - LLC (Low layer compatibility) Encapsulation is needed when several protocols are carried over the same VC. In order to allow the receiver to properly process the incoming AAL5 CPCS-PDU, the Payload Field must contain information necessary to identify the protocol of the routed or bridged PDU. In LLC Encapsulation this informationis encoded in an LLC header placed in front of the carried PDU.
OBJECT-TYPE    
  INTEGER notApplicable(1), none(2), rfc1483(3), pppVcMuxed(4), pppLlcMuxed(5)  

atmEtherCnfgAllocatedBuffers 1.3.6.1.4.1.164.12.4.3.4.2.1.20
This object enables user to limit the amount of buffers used by the connection. The limit set by this object will give the effect of a virtual buffer pool per connection. The user can allocate between 10 to 217 buffers to every connection. By default the limit is 50 buffers. Sum of limits allocated to all connections must not exceed the total amount of available buffers. Whenever a connection exceeds it's buffer limit due to congestion or burst traffic is discarded
OBJECT-TYPE    
  Integer32 10..217  

atmSuCrossConnectTranslate 1.3.6.1.4.1.164.12.4.3.5
OBJECT IDENTIFIER    

atmTranslateTable 1.3.6.1.4.1.164.12.4.3.5.1
This table translates the three of AtmIfIndex,AtmVpi,AtmVci to ifIndex of the interface on the user port's side.
OBJECT-TYPE    
  SEQUENCE OF  
    AtmTranslateEntry

atmTranslateEntry 1.3.6.1.4.1.164.12.4.3.5.1.1
An entry includes the User side interface's ifIndex of any virtual connection along with the ATM connection indices.
OBJECT-TYPE    
  AtmTranslateEntry  

atmTranslateAtmIfIndex 1.3.6.1.4.1.164.12.4.3.5.1.1.1
The ifIndex associated to the ATM interface.
OBJECT-TYPE    
  Integer32  

atmTranslateAtmVpi 1.3.6.1.4.1.164.12.4.3.5.1.1.2
The Vpi number of the ATM end point.
OBJECT-TYPE    
  Integer32 1..4095  

atmTranslateAtmVci 1.3.6.1.4.1.164.12.4.3.5.1.1.3
The Vci number of the ATM end point.
OBJECT-TYPE    
  Integer32 0..65535  

atmTranslateUserIfIndex 1.3.6.1.4.1.164.12.4.3.5.1.1.4
The ifIndex associated to the user interface.
OBJECT-TYPE    
  Integer32  

Defined Objects

AtmSuSystemHistoryAlrEntry  
SEQUENCE    
  Integer32 as atmSuSystemHistoryAlrIndex  
  Integer32 as atmSuSystemHistoryAlrIfIndex  
  DisplayString as atmSuSystemHistoryAlrDescription  
  INTEGER as atmSuSystemHistoryAlrStatus  
  DisplayString as atmSuSystemHistoryAlrOccurrenceTime  
  Integer32 as atmSuSystemHistoryAlrVpi  
  Integer32 as atmSuSystemHistoryAlrVci  

AtmSuSystemCurrentAlrEntry  
SEQUENCE    
  Integer32 as atmSuSystemCurrentAlrIndex  
  Integer32 as atmSuSystemCurrentAlrIfIndex  
  DisplayString as atmSuSystemCurrentAlrDescription  

AtmSuPortDataCnfgEntry  
SEQUENCE    
  INTEGER as atmSuPortDataApplication  
  INTEGER as atmSuPortDataRate  
  INTEGER as atmSuPortDataDCD  
  INTEGER as atmSuPortDataMode  
  INTEGER as atmSuPortDataCRC  
  INTEGER as atmSuPortDataClock  
  Integer32 as atmSuPortDataMaxNoOfConns  
  Integer32 as atmSuPortDataConfNoOfConns  
  Integer32 as atmSuPortDataIdleCode  
  INTEGER as atmSuPortDataInterfaceType  
  INTEGER as atmSuPortDataClkPolarity  
  INTEGER as atmSuPortDataCtsStatus  
  INTEGER as atmSuPortDataRtsStatus  

AtmSuPortDs1CnfgEntry  
SEQUENCE    
  INTEGER as atmSuPortDs1CnfgRxSensitivity  
  INTEGER as atmSuPortDs1CnfgLBO  
  INTEGER as atmSuPortDs1CnfgRestoreTime  
  INTEGER as atmSuPortDs1CnfgInbandMng  
  Integer32 as atmSuPortDs1CnfgDedicatedTs  

AtmSuPortDs1CbrCnfgEntry  
SEQUENCE    
  Integer32 as atmSuPortDs1CbrIdleCode  
  TimeSlots as atmSuPortDs1CbrRxTimeSlots  
  TimeSlots as atmSuPortDs1CbrTxTimeSlots  
  Integer32 as atmSuPortDs1CbrMaxNoOfConns  
  Integer32 as atmSuPortDs1CbrConfNoOfConns  
  INTEGER as atmSuPortDs1CbrSignallingSampleTime  

AtmSuPortAtmCnfgEntry  
SEQUENCE    
  INTEGER as atmSuPortAtmCnfgIdleCellCLP  
  INTEGER as atmSuPortAtmCnfgScramble  
  Integer32 as atmSuPortAtmSNMPVpi  
  Integer32 as atmSuPortAtmSNMPVci  
  INTEGER as atmSuPortAtmSNMPStatus  
  INTEGER as atmSuPortAtmILMIStatus  
  IpAddress as atmSuPortAtmSNMPIp  
  INTEGER as atmSuPortAtmCnfgCDVOptimization  
  INTEGER as atmSuPortAtmCnfgShapingMode  
  AtmTrafficDescrParamIndex as atmSuPortAtmSNMPTrafficDescrIndex  

AtmSuPortAtmIfStatsEntry  
SEQUENCE    
  Counter32 as atmSuPortAtmRxClp0Cells  
  Counter32 as atmSuPortAtmRxClp1Cells  
  Counter32 as atmSuPortAtmRxEfciSetCells  
  Counter32 as atmSuPortAtmRxOamCells  
  Counter32 as atmSuPortAtmTxClp0Cells  
  Counter32 as atmSuPortAtmTxClp1Cells  
  Counter32 as atmSuPortAtmTxEfciSetCells  
  Counter32 as atmSuPortAtmTxOamCells  

AtmSuPortAtmVclStatsEntry  
SEQUENCE    
  Counter32 as atmSuPortAtmVclStatsRxCells  
  Counter32 as atmSuPortAtmVclStatsRxClp0Cells  
  Counter32 as atmSuPortAtmVclStatsRxClp1Cells  
  Counter32 as atmSuPortAtmVclStatsRxDiscardsCells  
  Counter32 as atmSuPortAtmVclStatsTxCells  
  Counter32 as atmSuPortAtmVclStatsTxClp0Cells  
  Counter32 as atmSuPortAtmVclStatsTxClp1Cells  
  Counter32 as atmSuPortAtmVclStatsRxTotalAISCells  
  Counter32 as atmSuPortAtmVclStatsRxTotalCCCells  
  Counter32 as atmSuPortAtmVclStatsTotalSuccLoopbacks  
  Counter32 as atmSuPortAtmVclStatsTotalFailLoopbacks  
  Counter32 as atmSuPortAtmVclStatsRxTotalRDICells  
  Counter32 as atmSuPortAtmVclStatsTotalLOCSeconds  
  Counter32 as atmSuPortAtmVclStatsRxTotalLoopbackRequests  
  Counter32 as atmSuPortAtmVclStatsTxTotalAISCells  
  Counter32 as atmSuPortAtmVclStatsTxTotalCCCells  
  Counter32 as atmSuPortAtmVclStatsTxTotalRDICells  
  Counter32 as atmSuPortAtmVclStatsTxTotalLoopbackResponses  
  Counter32 as atmSuPortAtmVclStatsTxTotalLoopbackRequests  
  Counter32 as atmSuPortAtmVclStatsRxTotalLoopbackResponses  

AtmSuPortFrLportEntry  
SEQUENCE    
  Integer32 as atmSuPortFrLportSNMPDlci  
  INTEGER as atmSuPortFrLportSNMPStatus  
  INTEGER as atmSuPortFrLportVCSigProtocol  
  INTEGER as atmSuPortFrLportVCSigProcedure  
  INTEGER as atmSuPortFrLportCLLM  
  IpAddress as atmSuPortFrLportSNMPIp  

AtmSuPortFrPvcEndptEntry  
SEQUENCE    
  Counter32 as atmSuPortFrPvcEndptTxFECNs  
  Counter32 as atmSuPortFrPvcEndptTxBECNs  
  Counter32 as atmSuPortFrPvcEndptTxDEs  
  Counter32 as atmSuPortFrPvcEndptRxFECNs  
  Counter32 as atmSuPortFrPvcEndptRxBECNs  

AtmSuPortDxiConfEntry  
SEQUENCE    
  INTEGER as atmSuPortDxiPortMode  
  INTEGER as atmSuPortDxiSigProtocol  
  Integer32 as atmSuPortDxiSigDfa  

AtmSuPortCmdEntry  
SEQUENCE    
  INTEGER as atmSuResetPortStatsCmd  
  INTEGER as atmSuResetConnsStatsCmd  

AtmSuPortEtherEntry  
SEQUENCE    
  IpAddress as atmSuPortEtherIP  
  IpAddress as atmSuPortEtherMask  
  IpAddress as atmSuPortEtherDefaultGateWayIp  
  Integer32 as atmSuPortEtherDefaultCrossConnectId  
  INTEGER as atmSuPortEtherDefaultGatewayStatus  
  INTEGER as atmSuPortEtherSNMPStatus  
  INTEGER as atmSuPortEtherFragmentation  
  INTEGER as atmSuPortEtherRIPMode  
  INTEGER as atmSuPortEtherBridgingMode  
  Integer32 as atmSuPortEtherARPTimeout  
  Integer32 as atmSuPortEtherAgingTime  
  INTEGER as atmSuPortEtherPppOEEnable  
  INTEGER as atmSuPortEtherStatus  

AtmFrDescrEntry  
SEQUENCE    
  Integer32 as atmFrDescrIndex  
  OBJECT IDENTIFIER as atmFrDescrType  
  INTEGER as atmFrDescrClp2De  
  INTEGER as atmFrDescrDe2Clp  
  INTEGER as atmFrDescrFecn2Efci  
  INTEGER as atmFrDescrMappingMode  
  RowStatus as atmFrDescrRowStatus  

AtmFrCnfgEntry  
SEQUENCE    
  Integer32 as atmFrCnfgCrossConnectIndex  
  Integer32 as atmFrCnfgAtmIfIndex  
  Integer32 as atmFrCnfgAtmVpi  
  Integer32 as atmFrCnfgAtmVci  
  Integer32 as atmFrCnfgFrIfIndex  
  Integer32 as atmFrCnfgDlci  
  INTEGER as atmFrCnfgAdminStatus  
  INTEGER as atmFrCnfgOperStatus  
  TimeStamp as atmFrCnfgLastChange  
  Integer32 as atmFrCnfgMappingDescrIndex  
  Integer32 as atmFrCnfgSscsDlci  
  AtmTrafficDescrParamIndex as atmFrCnfgTrafficDescrIndex  
  INTEGER as atmFrCnfgPriority  
  RowStatus as atmFrCnfgRowStatus  
  Integer32 as atmFrCnfgAllocatedBuffers  

AtmDxiCnfgEntry  
SEQUENCE    
  Integer32 as atmDxiCnfgCrossConnectIndex  
  Integer32 as atmDxiCnfgAtmIfIndex  
  Integer32 as atmDxiCnfgAtmVpi  
  Integer32 as atmDxiCnfgAtmVci  
  Integer32 as atmDxiCnfgDxiIfIndex  
  Integer32 as atmDxiCnfgDfa  
  INTEGER as atmDxiCnfgAdminStatus  
  INTEGER as atmDxiCnfgOperStatus  
  TimeStamp as atmDxiCnfgLastChange  
  AtmTrafficDescrParamIndex as atmDxiCnfgTrafficDescrIndex  
  INTEGER as atmDxiCnfgPriority  
  RowStatus as atmDxiCnfgRowStatus  

AtmCbrCnfgEntry  
SEQUENCE    
  Integer32 as atmCbrCnfgAtmIfIndex  
  Integer32 as atmCbrCnfgAtmVpi  
  Integer32 as atmCbrCnfgAtmVci  
  Integer32 as atmCbrCnfgCbrIfIndex  
  INTEGER as atmCbrCnfgAdminStatus  
  INTEGER as atmCbrCnfgOperStatus  
  TimeStamp as atmCbrCnfgLastChange  
  INTEGER as atmCbrCnfgAAL1Signalling  
  TimeSlots as atmCbrCnfgRxTimeSlots  
  Integer32 as atmCbrCnfgRxBytesPerCell  
  TimeSlots as atmCbrCnfgTxTimeSlots  
  Integer32 as atmCbrCnfgTxBytesPerCell  
  INTEGER as atmCbrCnfgParity  
  RowStatus as atmCbrCnfgRowStatus  
  INTEGER as atmCbrCnfgService  

AtmCESConfExtnsEntry  
SEQUENCE    
  TimeStamp as atmCESLastChange  
  Integer32 as atmCESRxBytesPerCell  
  Integer32 as atmCESTxBytesPerCell  
  INTEGER as atmCESAal1Type  
  INTEGER as atmCESParity  
  INTEGER as atmCESSigType  
  OCTET STRING as atmCESSigABBits  

AtmEtherCnfgEntry  
SEQUENCE    
  Integer32 as atmEtherCnfgCrossConnectIndex  
  Integer32 as atmEtherCnfgAtmIfIndex  
  Integer32 as atmEtherCnfgAtmVpi  
  Integer32 as atmEtherCnfgAtmVci  
  Integer32 as atmEtherCnfgEtherIfIndex  
  MacAddress as atmEtherCnfgMacAddr  
  INTEGER as atmEtherCnfgAdminStatus  
  INTEGER as atmEtherCnfgOperStatus  
  TimeStamp as atmEtherCnfgLastChange  
  AtmTrafficDescrParamIndex as atmEtherCnfgTrafficDescrIndex  
  INTEGER as atmEtherCnfgEncapsulationMode  
  INTEGER as atmEtherCnfgPriority  
  RowStatus as atmEtherCnfgRowStatus  
  IpAddress as atmEtherCnfgRouterIP  
  IpAddress as atmEtherCnfgRouterMask  
  INTEGER as atmEtherCnfgRouterFragmentation  
  INTEGER as atmEtherCnfgRouterRIPMode  
  Integer32 as atmEtherCnfgRouterMTU  
  INTEGER as atmEtherCnfgPPPEncapsulation  
  Integer32 as atmEtherCnfgAllocatedBuffers  

AtmTranslateEntry  
SEQUENCE    
  Integer32 as atmTranslateAtmIfIndex  
  Integer32 as atmTranslateAtmVpi  
  Integer32 as atmTranslateAtmVci  
  Integer32 as atmTranslateUserIfIndex