
| rad | 1.3.6.1.4.1.164 | ||
| RAD MIB, version 485. | |||
| MODULE-IDENTITY | |||
| radTokenRing | 1.3.6.1.4.1.164.1 | ||
| OBJECT IDENTIFIER | |||
| trGen | 1.3.6.1.4.1.164.1.1 | ||
| OBJECT IDENTIFIER | |||
| agnRR | 1.3.6.1.4.1.164.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| agnRRcoprocHwVersion | 1.3.6.1.4.1.164.1.1.1.1 | ||
| ASCII string for description and display of the CML\IB hardware version. If the entry is not applicable, it will display the string -NOT APPLICABLE- | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| agnRRrecMode | 1.3.6.1.4.1.164.1.1.1.2 | ||
| The manager station can assist the agent in the autorecovery process by setting this value to SLOW(1). This value indicates the presence of old modules within the radring hub. Autorecovery process will be faster for new modules. However it might fail if set to FAST(2) and old modules are inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), slow(2), fast(3), notSupported(4) | ||
| agnRRmaskIBMalrt | 1.3.6.1.4.1.164.1.1.1.3 | ||
| When this object is set to the value of Enabled(3), Agent-traps that are not masked will also be sent to the IBM LAN manager using IBM's Alert Transport Service Protocol. This object is applicable only for TR agents. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disabled(2), enabled(3) | ||
| agnRRResetConfig | 1.3.6.1.4.1.164.1.1.1.4 | ||
| Setting the value to ON(3)is interpreted as a reset command for the agent NV Ram. When reset process is ended, a trap will be issued. If the entry is not applicable, The value notSupported will be read. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), notSupported(4) | ||
| agnRRSwReset | 1.3.6.1.4.1.164.1.1.1.5 | ||
| Setting the value to ON(3)is interpreted as a software reset command for the agent. When reset process is ended, a trap will be issued. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnRRRingReportMngr | 1.3.6.1.4.1.164.1.1.1.6 | ||
| Setting the value to ON(3) is interpreted as assigning the duty of Ring Report Manager on the agent | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnRRSubSysCommState | 1.3.6.1.4.1.164.1.1.1.7 | ||
| This attribute indicates the status of communication between the two agent's processors. The communication is failed when the CML/NM card is removed | |||
| OBJECT-TYPE | |||
| INTEGER | failed(2), ok(3), notSupported(4) | ||
| ringTR | 1.3.6.1.4.1.164.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| ringResetStatistics | 1.3.6.1.4.1.164.1.1.2.1 | ||
| Setting the value of this attribute to ON(3) resets all the inband statistics and error counters. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| ringCurrentTraffic | 1.3.6.1.4.1.164.1.1.2.2 | ||
| Momentary traffic for the last time interval. The traffic is expressed in percents of the maximum Tokenring traffic . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringPeakTraffic | 1.3.6.1.4.1.164.1.1.2.3 | ||
| Maximal traffic value since last reset of Agent or statistics. Expressed in percents of the maximum Tokenring traffic. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringTrafficTreshold | 1.3.6.1.4.1.164.1.1.2.4 | ||
| Traffic threshold value. When reached, a trap will be sent to the management console. Expressed in percents of the maximum Tokenring traffic | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringLineErrCnt | 1.3.6.1.4.1.164.1.1.2.5 | ||
| This counter is incremented when a frame or token is copied or repeated by any of the stations on the ring, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ringLineErr | 1.3.6.1.4.1.164.1.1.2.6 | ||
| This counter is incremented when a frame or token is copied or repeated by any of the stations on the ring, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringBurstErrCnt | 1.3.6.1.4.1.164.1.1.2.7 | ||
| This counter is incremented when any of the stations on the ring detects the absence of transitions for five half-bit timers (burst-five error). | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ringBurstErr | 1.3.6.1.4.1.164.1.1.2.8 | ||
| This counter is incremented when any of the stations on the ring detects the absence of transitions for five half-bit timers (burst-five error). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringACFCErrCnt | 1.3.6.1.4.1.164.1.1.2.9 | ||
| This counter is incremented when any of the stations on the ring receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ringACFCErr | 1.3.6.1.4.1.164.1.1.2.10 | ||
| This counter is incremented when any of the stations on the ring receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringTotErrCnt | 1.3.6.1.4.1.164.1.1.2.11 | ||
| The total of the above described errors | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| ringTotErr | 1.3.6.1.4.1.164.1.1.2.12 | ||
| The total of the above described errors | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringTotErrThreshold | 1.3.6.1.4.1.164.1.1.2.13 | ||
| The threshold value of the total of the above described errors.When the threshold is reached a trap indicating the status of the ring (SOFT ERROR)will be sent to the management station | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ringStatus | 1.3.6.1.4.1.164.1.1.2.14 | ||
| Describes the status of the LAN segment the agent is attached to: Normal(2) - The LAN segment is operating normally SoftError(3) - The Token ring LAN segment (ring) is experiencing intermittent failures that temporarily harm the ring's performance and cause data to be transmitted more than ones. Beaconing(4) - The ring is not operative; no data is transmitted. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), normal(2), softError(3), beacon(4) | ||
| ringConfigMsg | 1.3.6.1.4.1.164.1.1.2.15 | ||
| Full configuration message coded in internal RAD application format. This entry describes ring information. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| ringCurrentTrafficCnt | 1.3.6.1.4.1.164.1.1.2.16 | ||
| Momentary traffic for the last time interval. The traffic is expressed as bits per second. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| segTR | 1.3.6.1.4.1.164.1.1.3 | ||
| OBJECT IDENTIFIER | |||
| segTRTable | 1.3.6.1.4.1.164.1.1.3.1 | ||
| Segments. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SegTREntry | |||
| segTREntry | 1.3.6.1.4.1.164.1.1.3.1.1 | ||
| An entry in table segTRTable. | |||
| OBJECT-TYPE | |||
| SegTREntry | |||
| segTRID | 1.3.6.1.4.1.164.1.1.3.1.1.1 | ||
| Segment unique identification number (internal). It is the extreme left slot, marking the beginning of the segment. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| segTRLastSlot | 1.3.6.1.4.1.164.1.1.3.1.1.2 | ||
| Location of the right most slot marking the end of the segment. In the RADring hub it is slot number 20 or the slot where end of segment module is inserted or the slot before a beginning of a new segment. ( End of segment module could be one with termination on or TIO, TFR, TCR etc.) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| segTRFirstSlot | 1.3.6.1.4.1.164.1.1.3.1.1.3 | ||
| Location of the left most slot marking the beginning of the segment. In the RADring hub it is slot number 1 or the slot number following the end of segment module, or where a repeater or TIO is inserted. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| segTRStatus | 1.3.6.1.4.1.164.1.1.3.1.1.4 | ||
| Describes the status of the segment : Normal(3) - The segment is operating normally Beaconing(2) - The ring is not operative; no data is transmitted. Segment without inband module within its limit will display Unknown(1). This entry is specially usefull when the hub is configured with multiple segments and each segment is part of another net | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), beaconing(2), normal(3) | ||
| moduleTR | 1.3.6.1.4.1.164.1.1.4 | ||
| OBJECT IDENTIFIER | |||
| mdlTRTable | 1.3.6.1.4.1.164.1.1.4.1 | ||
| Modules parameters structure contains general information about the modules. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlTREntry | |||
| mdlTREntry | 1.3.6.1.4.1.164.1.1.4.1.1 | ||
| An entry in table mdlTRTable. | |||
| OBJECT-TYPE | |||
| MdlTREntry | |||
| mdlTRID | 1.3.6.1.4.1.164.1.1.4.1.1.1 | ||
| The slot number where the module is inserted. Can not be greater than chNoSlot | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlTRSegID | 1.3.6.1.4.1.164.1.1.4.1.1.2 | ||
| The segment number where the module belongs to. One of the segTRID values. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlTRType | 1.3.6.1.4.1.164.1.1.4.1.1.3 | ||
| Indicates the type of the module connected at the specified slot number. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), tl4s(3), tl4su(4), tl4sd(5), tl4cx(6), tl4u(7), tl2edu(8), tl2eds(9), tl2edsu(10), tl2f(11), tja(12), tio(13), tfr(14), tfc1(15), tfc2(16), tcr(17), tl4au(18), tl4as(19), tl4asd(20), tl4asu(21), tre1d(22), tre(23), tre8d(24), stc1(25), stc2(26), ftc(27), cmlib(28), tl2fsat(29), nonTR(30), tau(31), rmu(32) | ||
| mdlTRHwVer | 1.3.6.1.4.1.164.1.1.4.1.1.4 | ||
| ASCII string for description and display of the module's hardware version, as it is known by the module's software. A manager can record his own hardware upgrade. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlTRSwVer | 1.3.6.1.4.1.164.1.1.4.1.1.5 | ||
| ASCII string for description and display of the module's software version. A value of NOT APPLICABLE will be recorded for module having no independent processor. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlTRTotalNoOfPrt | 1.3.6.1.4.1.164.1.1.4.1.1.6 | ||
| This entry describes the number of possible ports/lobes/links connection in the module (not all ports hardware should be active) . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlTRSpecific | 1.3.6.1.4.1.164.1.1.4.1.1.7 | ||
| Object identifier of entity containing additional information regarding this instance. This entry is type specific. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| prtTR | 1.3.6.1.4.1.164.1.1.5 | ||
| OBJECT IDENTIFIER | |||
| prtTRTable | 1.3.6.1.4.1.164.1.1.5.1 | ||
| TReral port table for any media type. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtTREntry | |||
| prtTREntry | 1.3.6.1.4.1.164.1.1.5.1.1 | ||
| An entry in table prtTRTable. | |||
| OBJECT-TYPE | |||
| PrtTREntry | |||
| prtTRModuleID | 1.3.6.1.4.1.164.1.1.5.1.1.1 | ||
| A unique identifier of the module(slot no.)this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTRID | 1.3.6.1.4.1.164.1.1.5.1.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTRFunctionality | 1.3.6.1.4.1.164.1.1.5.1.1.3 | ||
| Describes the functionality of the port in a Token ring topology or other implementations. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ringin(2), ringout(3), satellite(4), lobe(5), link(6), tja(7), none(8), smart-port(9) | ||
| prtTRConnectorType | 1.3.6.1.4.1.164.1.1.5.1.1.4 | ||
| Type of hardware connector in the port. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), idc(2), rj45(3), srj45(4), db9(5), bnc(6), foSt(7), db25(8) | ||
| prtTRAdminCmd | 1.3.6.1.4.1.164.1.1.5.1.1.5 | ||
| By setting this attribute to DISABLE(2) or SHORT(4) the management station can force this lobe/port/link-connection to be removed and block any access to the network via this lobe/port/link. It is not mandatory that a certain lobe/port/link will support all the enumerated states. The state of the lobe/port/link is type specific and indicated within the specific group | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disable(2), enable(3), short(4), normal(5) | ||
| prtTRActiveState | 1.3.6.1.4.1.164.1.1.5.1.1.6 | ||
| This attribute describes the electrical or optical activity state of a lobe or the state of a port. Certain values may not be applicable in some cases | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3), standby(4) | ||
| prtTRTrapMaskEnable | 1.3.6.1.4.1.164.1.1.5.1.1.7 | ||
| When this attribute is set to OFF by the management console the agent starts sending the unmasked traps related to this port. Otherwise no traps from this port are sent. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtTRstatus | 1.3.6.1.4.1.164.1.1.5.1.1.8 | ||
| This attribute indicates the status of this lobe/port connection: DISABLED - (2) to (6) indicates the reason for the disabled state. INSERTED - (7)indicates that the lobe hardware inserts this lobe into the ring , thus it becomes part of the ring. BYPASS - (8)indicates that the ring bypasses this lobe and the lobe hardware provides loopback connection towards the station for media test purposes. FORCEDLOOP - (9) indicates the port is in a loopback state and the main ring is connected to the backup path. TRUNKFAIL - (10) indicates that the ring connection is broken for a repeater, converter or a cable protector. NORMAL - (11) indicates the port is in normal condition. It is not mandatory that a certain lobe/port will support all the enumerated states. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disabledManuall(2), disabledAutorec(3), disabledSecurity(4), disableAuto(5), disableFlip(6), inserted(7), bypass(8), forcedloop(9), trunkfail(10), normal(11) | ||
| prtTRCableProtectEnable | 1.3.6.1.4.1.164.1.1.5.1.1.9 | ||
| The value of this attribute determines activation of the cable-fault protection mechanism of TCR and the optical link mechanism of TFR and TFC . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3), inhibit(4) | ||
| prtTRCableState | 1.3.6.1.4.1.164.1.1.5.1.1.10 | ||
| The value of this attribute determines the cable status of TCR and the optical link mechanism of TFR and TFC . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), failed(2), normal(3), remoteFailed(4) | ||
| prtTRMACAddress | 1.3.6.1.4.1.164.1.1.5.1.1.11 | ||
| The value of this object is the specific MAC address of this interface which uniquely identifies this Interface on a ring. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtTRSpecific | 1.3.6.1.4.1.164.1.1.5.1.1.12 | ||
| Object identifier of entity containing additional information regarding this instance. This entry is type specific. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| prtTRMacAddressTable | 1.3.6.1.4.1.164.1.1.5.2 | ||
| . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtTRMacAddressEntry | |||
| prtTRMacAddressEntry | 1.3.6.1.4.1.164.1.1.5.2.1 | ||
| An entry in table prtTRMacAddressTable. | |||
| OBJECT-TYPE | |||
| PrtTRMacAddressEntry | |||
| prtTRMacAddressModuleID | 1.3.6.1.4.1.164.1.1.5.2.1.1 | ||
| A unique identifier of the module(slot no.)this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTRMacAddressPortID | 1.3.6.1.4.1.164.1.1.5.2.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTRMacAddressID | 1.3.6.1.4.1.164.1.1.5.2.1.3 | ||
| A identifier of the MAC address in the list according to the ring order | |||
| OBJECT-TYPE | |||
| Integer32 | 1..250 | ||
| prtTRMACAddressValue | 1.3.6.1.4.1.164.1.1.5.2.1.4 | ||
| MAC address from the list of addresses connected to this port | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| radRing | 1.3.6.1.4.1.164.1.2 | ||
| OBJECT IDENTIFIER | |||
| chasRR | 1.3.6.1.4.1.164.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| chType | 1.3.6.1.4.1.164.1.2.1.1 | ||
| This value indicates which type of enclosure the Rad agent is managing. The default value will be RadRing | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| chNoSlot | 1.3.6.1.4.1.164.1.2.1.2 | ||
| This value indicates the number of manageable slots in the chassis. Not all slots must be occupied. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chPSPrimary | 1.3.6.1.4.1.164.1.2.1.3 | ||
| This attribute indicates the status of the main (primary) power supply unit | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), fault(3), active(4), recovered(5), none(6) | ||
| chPSSecondary | 1.3.6.1.4.1.164.1.2.1.4 | ||
| This attribute indicates the status of the secondary power supply unit | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), fault(3), active(4), recovered(5), none(6) | ||
| chTemperature | 1.3.6.1.4.1.164.1.2.1.5 | ||
| This attribute indicates if the internal hub temperature exceeded the permissible maximum | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), exceed(2) | ||
| chEtMainClock | 1.3.6.1.4.1.164.1.2.1.6 | ||
| This attribute indicates the status of Eternet repeater main clock in RadRingII hub | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ok(2), fault(3) | ||
| chEtSecClock | 1.3.6.1.4.1.164.1.2.1.7 | ||
| This attribute indicates the status of Eternet repeater secondary clock in RadRingII hub | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ok(2), fault(3) | ||
| segRR | 1.3.6.1.4.1.164.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| segRRSecurityTable | 1.3.6.1.4.1.164.1.2.2.1 | ||
| RADRing segments' specific information | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SegRRSecEntry | |||
| segRRSecEntry | 1.3.6.1.4.1.164.1.2.2.1.1 | ||
| An entry in table segRRSecurityTable. | |||
| OBJECT-TYPE | |||
| SegRRSecEntry | |||
| segRRID | 1.3.6.1.4.1.164.1.2.2.1.1.1 | ||
| Segment unique identification number (internal). It is the extreme left slot, marking the beginning of the segment. TR segment no.: 1 .. 20 Ethernet segment no.: 21. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..21 | ||
| segRRSecID | 1.3.6.1.4.1.164.1.2.2.1.1.2 | ||
| Segment's security unique identification number | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| segRRSecEnable | 1.3.6.1.4.1.164.1.2.2.1.1.3 | ||
| This entry indicates whether the specific segment's security is active or not | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| segRRSecurityPattern | 1.3.6.1.4.1.164.1.2.2.1.1.4 | ||
| A six-octet (48 bit) pattern, where the masked bits of segTRSecurityMask need to match the MAC address of each port within the segment. A Value of all-zeros indicates no security. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| segRRSecurityMask | 1.3.6.1.4.1.164.1.2.2.1.1.5 | ||
| Mask of the allowed MAC address that can be connected through the ports within the segment | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| moduleRR | 1.3.6.1.4.1.164.1.2.3 | ||
| OBJECT IDENTIFIER | |||
| mdlRRTable | 1.3.6.1.4.1.164.1.2.3.1 | ||
| RADRing specific modules' information | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlRREntry | |||
| mdlRREntry | 1.3.6.1.4.1.164.1.2.3.1.1 | ||
| An entry in table mdlRRTable. | |||
| OBJECT-TYPE | |||
| MdlRREntry | |||
| mdlRRid | 1.3.6.1.4.1.164.1.2.3.1.1.1 | ||
| Unique number to identify the module. It indicates the slot number the module is inserted in. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlRRTLRstatus | 1.3.6.1.4.1.164.1.2.3.1.1.2 | ||
| This entry specifies the status of the setup on the TL-2/Exx modules. When the value is ON, lobe one is the only active lobe. This entry will have the value UNKNOWN for all other modules | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlRRtermination | 1.3.6.1.4.1.164.1.2.3.1.1.3 | ||
| Attribute describing the termination state as set by the switches on the lobe modules | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlRRReset | 1.3.6.1.4.1.164.1.2.3.1.1.4 | ||
| When this object is set to the value of ON(3), the module performs software reset. Upon completion, a trap will be issued to the management station and the value will be set to OFF. This entry will have the value of UNKNOWN (1) for modules without independent processors. This command should be masked for the agent module | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlRRLed | 1.3.6.1.4.1.164.1.2.3.1.1.5 | ||
| This entry specifies the LEDs status in the module . Each led will be represented by 4 bits where the first 2 bits will specify the status (NA, OFF, ON, BLINK), and the next two bits will specify the color (RED, GREEN, YELLOW) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlRRSpeed | 1.3.6.1.4.1.164.1.2.3.1.1.6 | ||
| Attribute describing the bandwidth of the media as set by the module switches. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), fourMegabit(2), sixteenMegabit(3), tenMegabit(4) | ||
| mdlRRMngAutoDis | 1.3.6.1.4.1.164.1.2.3.1.1.7 | ||
| Attribute describing the setup of the MNG switch on the TL- Active cards. Value ON indicates the ability of activating the auto-disable mechanism of the card via management command. Value OFF indicates that the activation of the auto-disable mechanism of the card is according to the switch setting.In this case the mdlRRAutodisable will not be available for write operation. Applicable to Token Ring cards only. Replaced by mdlRRMngState. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlRRAutodisable | 1.3.6.1.4.1.164.1.2.3.1.1.8 | ||
| This attribute can be set by the manager if the value of mdlRRMngAutoDis is ON. It controls the behavior of the Active cards regarding the Auto-disable mechanism. All ports will be in the same mode. Applicable to Token Ring cards only. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| mdlRRConfigMsg | 1.3.6.1.4.1.164.1.2.3.1.1.9 | ||
| Full configuration message coded in internal RAD application format. This entry describes module' configuration. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlRRMngState | 1.3.6.1.4.1.164.1.2.3.1.1.10 | ||
| This entry indicates the setting of the module's switches. ENABLE means that the module can accept management commands. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disable(2), enable(3) | ||
| mdlRRType | 1.3.6.1.4.1.164.1.2.3.1.1.11 | ||
| Indicates the type of the module installed in the specified slot number. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), tl4s(3), tl4su(4), tl4sd(5), tl4cx(6), tl4u(7), tl2edu(8), tl2eds(9), tl2edsu(10), tl2f(11), tja(12), tio(13), tfr(14), tfc1(15), tfc2(16), tcr(17), tl4au(18), tl4as(19), tl4asd(20), tl4asu(21), tre1d(22), tre(23), tre8d(24), stc1(25), stc2(26), ftc(27), cmlib(28), tl2fsat(29), taV24(30), taV11(31), wangVs(32), ta3x74(33), ta3x(34), sat-asu(35), sat-asd(36), sat-su(37), sat-sd(38), ep8t(39), ep4taui(40), ep4t2fl(41), ep4tfl(42), ep4fl(43), epr8t(45), epr4taui(46), epr4t2fl(47), epr4tfl(48), epr4fl(49), tl2fm(51), ftc2(53), mlbt(54), mlbtf(55), ftbDfo(56), ftbSfo(57), mbe8d(58), mbe1d(59), cmlibE(60) | ||
| mdlRRHwVer | 1.3.6.1.4.1.164.1.2.3.1.1.12 | ||
| ASCII string for description and display of the module's hardware version, as it is known by the module's software. A manager can record his own hardware upgrade. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlRRSwVer | 1.3.6.1.4.1.164.1.2.3.1.1.13 | ||
| ASCII string for description and display of the module's software version. A value of NOT APPLICABLE will be recorded for a module having no independent processor. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlRRSpecific | 1.3.6.1.4.1.164.1.2.3.1.1.14 | ||
| Object identifier of entity containing additional information regarding this instance. This entry is module type specific. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| mdlIBTable | 1.3.6.1.4.1.164.1.2.3.2 | ||
| Additional parameters that can be monitored for a segment with an inband module. Module specific for Token Ring | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlIBEntry | |||
| mdlIBEntry | 1.3.6.1.4.1.164.1.2.3.2.1 | ||
| An entry in table mdlIBTable. | |||
| OBJECT-TYPE | |||
| MdlIBEntry | |||
| mdlIBid | 1.3.6.1.4.1.164.1.2.3.2.1.1 | ||
| Unique number to identify the CML\IB module. It indicates the slot number the module is inserted in | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlIBsegID | 1.3.6.1.4.1.164.1.2.3.2.1.2 | ||
| Unique number to identify the segment where the CML\IB module is inserted. It is one of the segTRID values. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlIBCorrelationEnable | 1.3.6.1.4.1.164.1.2.3.2.1.3 | ||
| When set to ON(3), the in-band agent should perform correlation each time a station enters/leaves the segment. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlIBAutorecEnable | 1.3.6.1.4.1.164.1.2.3.2.1.4 | ||
| When set to ON(3), the in-band agent should perform autorecovery each time a beacon status is detected. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlIBAutorecResult | 1.3.6.1.4.1.164.1.2.3.2.1.5 | ||
| When autorecovery is completed the result will be reported (3)..(7). While in autorecovery process, started(2) will be reported. Before autorecovery process, notStarted(1) will be reported. | |||
| OBJECT-TYPE | |||
| INTEGER | notStarted(1), started(2), segmentOk(3), segmentFixed(4), segmentClosed(5), failed(6), hubProblem(7) | ||
| mdlIBcommand | 1.3.6.1.4.1.164.1.2.3.2.1.6 | ||
| When this object is set to the value of open(2), the station should go into the open state. The progress and success of this command is given by the values of the object mdlIBstate. When this object is set to the value of reset(3), then the station should do a reset. On a reset, all MIB counters should retain their values, if possible. Other side effects depend on the hardware chip set. When this object is set to the value of close(4), the station should go into the closed state by removing itself from the ring. Setting this object to a value of no-op(1) has no effect. For read operation, this object has always a value of no-op(1). It is not permitted to apply this command on an agent module. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), open(2), reset(3), close(4) | ||
| mdlIBstate | 1.3.6.1.4.1.164.1.2.3.2.1.7 | ||
| The current adapter status, which can be used to diagnose fluctuating problems. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), opened(2), closed(3), opening(4), closing(5), badParam(6), lobeFailed(7), signalLoss(8), insertionTimeout(9), ringFailed(10), beaconning(11), duplicateMac(12), requestFailed(13), removeReceived(14), budFailure(15), initFailure(16) | ||
| mdlIBagnt | 1.3.6.1.4.1.164.1.2.3.2.1.8 | ||
| Indicates whether the specific inband module serves as: - Active hub agent - (on) - Ring Monitor (for TR module only) - (off) - Standby agent - (standBy) | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), standBy(4) | ||
| mdlIBIpAddress | 1.3.6.1.4.1.164.1.2.3.2.1.9 | ||
| Indicates IP address of the module if the module serves as an agent of itself. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| mdlIBLocalMacAddr | 1.3.6.1.4.1.164.1.2.3.2.1.10 | ||
| The value of this object is the specific MAC address of this interface which uniquely identifies this interface on a ring.It is the address set by the management and upon request it will replace the burn in address. Non-canonical format. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| mdlIBLocalAddrStatus | 1.3.6.1.4.1.164.1.2.3.2.1.11 | ||
| The value of this object specifies whether the specific MAC address of this interface was set by the local management or it is the burn-in address in use. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlIBbrnInMacAddr | 1.3.6.1.4.1.164.1.2.3.2.1.12 | ||
| The value of this object is the specific Burn-in MAC address of this interface which uniquely identifies this interface on a ring. Non-canonical format. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| mdlIBTrapMaskEnable | 1.3.6.1.4.1.164.1.2.3.2.1.13 | ||
| When this attribute is set to OFF by the management console, the agent starts sending the unmasked traps related to this module. Otherwise, no traps are sent by this module. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlBRGTable | 1.3.6.1.4.1.164.1.2.3.3 | ||
| Special modules such as bridges/converters that are within the hub | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlBRGEntry | |||
| mdlBRGEntry | 1.3.6.1.4.1.164.1.2.3.3.1 | ||
| An entry in table mdlBRGTable. | |||
| OBJECT-TYPE | |||
| MdlBRGEntry | |||
| mdlBRGid | 1.3.6.1.4.1.164.1.2.3.3.1.1 | ||
| Unique number to identify the module. It indicates the slot number the module is inserted in. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlBRGReady | 1.3.6.1.4.1.164.1.2.3.3.1.2 | ||
| This entry will have the value ON when packets can be transferred in the TRE module. The value UNKNOWN will be used for all other modules where this characteristic is not applicable | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3), blink(4) | ||
| mdlBRGStatus | 1.3.6.1.4.1.164.1.2.3.3.1.3 | ||
| This entry specifies the status of operation of the STC or FTC modules. For other modules this value will read NOAP | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlBRGLocation | 1.3.6.1.4.1.164.1.2.3.3.1.4 | ||
| This entry indicates the configuration mode: - for the TRE bridge (main/remote) - for MLB-T, MLBT-F (main/secondary) | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), main(2), remote(3), secondary(4) | ||
| mdlBRGIpAddress | 1.3.6.1.4.1.164.1.2.3.3.1.5 | ||
| Indicates IP address of the module if the module serves as an agent of itself. For all other modules the IP value will be 0.0.0.0 | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| mdlBRGMacAddr | 1.3.6.1.4.1.164.1.2.3.3.1.6 | ||
| The value of this object is the specific MAC address of this interface which uniquely identifies this interface on a ring. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| mdlBRGAdapterState | 1.3.6.1.4.1.164.1.2.3.3.1.7 | ||
| The current adapter status, which can be used to diagnose fluctuating problems. This object is applicable only for TR bridges with adapter. The value 'unknown' will be used for other module types. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), opened(2), closed(3), opening(4), closing(5), badParam(6), lobeFailed(7), signalLoss(8), insertionTimeout(9), ringFailed(10), beaconning(11), duplicateMac(12), requestFailed(13), removeReceived(14), budFailure(15), initFailure(16) | ||
| mdlBRGBypassSw | 1.3.6.1.4.1.164.1.2.3.3.1.8 | ||
| This entry is applicable only for FTB-D/FO module. It describes the status of the Bypass Switch. The value UNKNOWN will be used for all other modules where this characteristic is not applicable | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlMMTable | 1.3.6.1.4.1.164.1.2.3.4 | ||
| Special 'WAN' modules that are within the RadRing hub | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlMMEntry | |||
| mdlMMEntry | 1.3.6.1.4.1.164.1.2.3.4.1 | ||
| An entry in table mdlMMTable. | |||
| OBJECT-TYPE | |||
| MdlMMEntry | |||
| mdlMMid | 1.3.6.1.4.1.164.1.2.3.4.1.1 | ||
| Unique number to identify the module. It indicates the slot number the module is inserted in. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlMMBertCmd | 1.3.6.1.4.1.164.1.2.3.4.1.2 | ||
| Setting this Object to ON, will start BERT test on all the channels that are currently in Remote Loop. If the value of mdlRRMngState is disabled, this parameter is read-only and reflects the module jumper setting. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| mdlETTable | 1.3.6.1.4.1.164.1.2.3.5 | ||
| 'Ethernet' modules that are within the hub | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlETEntry | |||
| mdlETEntry | 1.3.6.1.4.1.164.1.2.3.5.1 | ||
| An entry in table mdlETTable. | |||
| OBJECT-TYPE | |||
| MdlETEntry | |||
| mdlETid | 1.3.6.1.4.1.164.1.2.3.5.1.1 | ||
| Unique number to identify the module. It indicates the slot number the module is inserted in. It is the same as rptrGroupIndex in the Repeater MIB | |||
| OBJECT-TYPE | |||
| Integer32 | 1..20 | ||
| mdlETSAmode | 1.3.6.1.4.1.164.1.2.3.5.1.2 | ||
| Setting this Object to ON, will change the mode of operation of the Ethernet card to a stand alone operation mode. It will disconnect the card from the repeater bus. The rptrGroupOperStatus parameter in the Repeater MIB is changed to other(1). The parameter is read-only when the value of mdlRRMngState is disabled | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| prtRR | 1.3.6.1.4.1.164.1.2.4 | ||
| OBJECT IDENTIFIER | |||
| prtRRTable | 1.3.6.1.4.1.164.1.2.4.1 | ||
| RADRing specific port information | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtRREntry | |||
| prtRREntry | 1.3.6.1.4.1.164.1.2.4.1.1 | ||
| An entry in table prtRRTable. | |||
| OBJECT-TYPE | |||
| PrtRREntry | |||
| prtRRmdlID | 1.3.6.1.4.1.164.1.2.4.1.1.1 | ||
| A unique identifier of the module,(slot no.),this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtRRID | 1.3.6.1.4.1.164.1.2.4.1.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtRRSecurityState | 1.3.6.1.4.1.164.1.2.4.1.1.3 | ||
| This entry indicates whether a security check can be performed on the specific port. This value is directly related to the presence of an inband module in the segment where the port belongs to and to activation of the correlation process. | |||
| OBJECT-TYPE | |||
| INTEGER | notactive(1), active(2) | ||
| prtRRSecurityEnable | 1.3.6.1.4.1.164.1.2.4.1.1.4 | ||
| This value indicates whether a security check should be performed. Setting this value to ON(3) will activate the security mechanism if and only if, the value of prtRRSecurityState is ACTIVE. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtRRSecurityMask | 1.3.6.1.4.1.164.1.2.4.1.1.5 | ||
| Mask of the allowed MAC address that can be connected through this port. The security of the individual port overwrites the security of the segment where the port belongs to | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtRRSecurityPattern | 1.3.6.1.4.1.164.1.2.4.1.1.6 | ||
| A six-octet(48 bit) pattern, where the masked bits of prtRRSecurityMask should match the MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtRRJitterAttenEnable | 1.3.6.1.4.1.164.1.2.4.1.1.7 | ||
| The value of this attribute determines activation of the jitters Attenuation mechanism of repeater's port . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| prtRRConfigMsg | 1.3.6.1.4.1.164.1.2.4.1.1.8 | ||
| Full configuration message coded in internal RAD application format. This entry describes port' configuration. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtRRFlipAutoDisable | 1.3.6.1.4.1.164.1.2.4.1.1.9 | ||
| Attribute describing the control on the flipping mechanism of a lobe . Value ON indicates the ability of the lobe to auto disable itself when flipping occur. Value OFF indicates that the auto disable mechanism should not be activated and the lobe should stay in a flipping state. This attribute applies on selected lobes (tl-2/f, or tl-2/fsat) | |||
| OBJECT-TYPE | |||
| INTEGER | noApplicable(1), off(2), on(3) | ||
| prtRRSecurityMask2 | 1.3.6.1.4.1.164.1.2.4.1.1.10 | ||
| Mask of the allowed MAC address that can be connected through this port. The security of the individual port overwrites the security of the segment where the port belongs to | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtRRSecurityPattern2 | 1.3.6.1.4.1.164.1.2.4.1.1.11 | ||
| A six-octet(48 bit) pattern: where the masked bits of prtRRSecurityMask2 should match the MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtRRMode | 1.3.6.1.4.1.164.1.2.4.1.1.12 | ||
| Indicates the port status of rr-sat card after the communication is broken. When configured to smart-port, the port disables itself when there is no management communication with attachment. interRptrPort - this port is used to connect an external repeater. No security can be set for this port. MAC Address is set to 0. No traps 'MAC Address changed' are generated. multiConnPort - this port is used for connection of external 4 port repeater. 8 securities per port exist. MAC Address is set to 0. No traps 'MAC Address changed' are generated. | |||
| OBJECT-TYPE | |||
| INTEGER | noApplicable(1), smart-port(2), port(3), interRptrPort(4), multiConnPort(5) | ||
| prtRRAttachment | 1.3.6.1.4.1.164.1.2.4.1.1.13 | ||
| Indicates the type of the port attachment. Smart attachment types are applicable for rr-sat card only | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), station(2), sLau2(3), sLau4(4) | ||
| prtMMTable | 1.3.6.1.4.1.164.1.2.4.2 | ||
| RADRing specific WAN modules port information. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMMEntry | |||
| prtMMEntry | 1.3.6.1.4.1.164.1.2.4.2.1 | ||
| An entry in table prtMMTable. | |||
| OBJECT-TYPE | |||
| PrtMMEntry | |||
| prtMMmdlID | 1.3.6.1.4.1.164.1.2.4.2.1.1 | ||
| A unique identifier of the module(slot no.)this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMMID | 1.3.6.1.4.1.164.1.2.4.2.1.2 | ||
| A unique identifier of the port (link) within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMMAdminCmd | 1.3.6.1.4.1.164.1.2.4.2.1.3 | ||
| Setting the object to locLoop(2) or remLoop(3) will activate the corresponding test. Value remLoop(3) activates the BERT test on the related link if mdlMMBertCmd is set to on(3). Setting parameter to normal(1), restores the normal operation of the link. The parameter is read-only when value of mdlRRMngState is disable | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), locLoop(2), remLoop(3) | ||
| prtMMOperStatus | 1.3.6.1.4.1.164.1.2.4.2.1.4 | ||
| Reflects the Synchronization status. | |||
| OBJECT-TYPE | |||
| INTEGER | operational(1), locSyncLoss(2), remSyncLoss(3) | ||
| prtMMTestStatus | 1.3.6.1.4.1.164.1.2.4.2.1.5 | ||
| Reflects the link status. When the object is set to the value of bert(4), it means that the remote loopback is active too. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), locLoop(2), remLoop(3), bert(4) | ||
| prtMMBertResult | 1.3.6.1.4.1.164.1.2.4.2.1.6 | ||
| The value of this object indicates the status of the last BERT test. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), fault(2), ok(3) | ||
| prtMMTrapMaskEnable | 1.3.6.1.4.1.164.1.2.4.2.1.7 | ||
| When this object is set to OFF by the management console, the agent starts sending the unmasked traps related to this module. Otherwise, no traps are sent by this module. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtETTable | 1.3.6.1.4.1.164.1.2.4.3 | ||
| RADRing specific Ethernet port information | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtETEntry | |||
| prtETEntry | 1.3.6.1.4.1.164.1.2.4.3.1 | ||
| An entry in table prtETTable. | |||
| OBJECT-TYPE | |||
| PrtETEntry | |||
| prtETmdlID | 1.3.6.1.4.1.164.1.2.4.3.1.1 | ||
| A unique identifier of the module, (slot no.), this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtETID | 1.3.6.1.4.1.164.1.2.4.3.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtETTrapMaskEnable | 1.3.6.1.4.1.164.1.2.4.3.1.3 | ||
| When this attribute is set to OFF by the management console, the agent starts sending the unmasked traps related to this port. Otherwise, no traps are sent by this port. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtRRSecTable | 1.3.6.1.4.1.164.1.2.4.4 | ||
| RR Port Security Table (10.08.95) | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtRRSecEntry | |||
| prtRRSecEntry | 1.3.6.1.4.1.164.1.2.4.4.1 | ||
| An entry in table prtRRSecTable. | |||
| OBJECT-TYPE | |||
| PrtRRSecEntry | |||
| prtRRSecmdlID | 1.3.6.1.4.1.164.1.2.4.4.1.1 | ||
| A unique identifier of the module,(slot no.),this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtRRSecPrtID | 1.3.6.1.4.1.164.1.2.4.4.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtRRSecID | 1.3.6.1.4.1.164.1.2.4.4.1.3 | ||
| A unique identifier of the security number within the port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtRRSecMask | 1.3.6.1.4.1.164.1.2.4.4.1.4 | ||
| Mask of the allowed MAC address that can be connected through this port. The security of the individual port overwrites the security of the segment, the port belongs to | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| prtRRSecPattern | 1.3.6.1.4.1.164.1.2.4.4.1.5 | ||
| A six-octet(48 bit) pattern, where the masked bits of prtRRSecMask should match the MAC address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| radFddi | 1.3.6.1.4.1.164.2 | ||
| OBJECT IDENTIFIER | |||
| radFddiStation | 1.3.6.1.4.1.164.2.1 | ||
| OBJECT IDENTIFIER | |||
| radFddiStationsNumber | 1.3.6.1.4.1.164.2.1.1 | ||
| The number of manageable Stations implemented in the box. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65535 | ||
| radFddiStationTable | 1.3.6.1.4.1.164.2.1.2 | ||
| A list of FddiStation entries. The number of entries is given by the value of radFddiStationsNumber. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadFddiStationEntry | |||
| radFddiStationEntry | 1.3.6.1.4.1.164.2.1.2.1 | ||
| An entry in table radFddiStationTable. | |||
| OBJECT-TYPE | |||
| RadFddiStationEntry | |||
| radFddiStationIndex | 1.3.6.1.4.1.164.2.1.2.1.1 | ||
| A unique value for each Station. Its value ranges between 1 and the value ofradFddiStationNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiStationType | 1.3.6.1.4.1.164.2.1.2.1.2 | ||
| Indicates the type of the station. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), singleAttachedStation(2), dualAttachedStation(3), singleAttachedConcentrator(4), dualAttachedConcentrator(5), nullAttachedConcentrator(6) | ||
| radFddiStationBus1TestResult | 1.3.6.1.4.1.164.2.1.2.1.3 | ||
| Indicates the result of a test performed on Bus1. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), faulty(2) | ||
| radFddiStationBus2TestResult | 1.3.6.1.4.1.164.2.1.2.1.4 | ||
| Indicates the result of a test performed on Bus2. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), faulty(2) | ||
| radFddiStationTempDeInsertAction | 1.3.6.1.4.1.164.2.1.2.1.5 | ||
| This action provides temporary deinsertion of the root station from the ring. Expressed in milliseconds. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| radFddiStationPerformTest | 1.3.6.1.4.1.164.2.1.2.1.6 | ||
| A value ON of this attribute indicates that a test should be performed upon the Station. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| radFddiStationOpticalSwitchStatus | 1.3.6.1.4.1.164.2.1.2.1.7 | ||
| A value ON of this attribute indicates that the Station is in bypass mode. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2), notSupported(255) | ||
| radFddiSMTTable | 1.3.6.1.4.1.164.2.2 | ||
| A list of FddiSMT entries. The number of entries is given by the value of snmpFddiSMTNumber. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadFddiSMTEntry | |||
| radFddiSMTEntry | 1.3.6.1.4.1.164.2.2.1 | ||
| An entry in table radFddiSMTTable. | |||
| OBJECT-TYPE | |||
| RadFddiSMTEntry | |||
| radFddiSMTIndex | 1.3.6.1.4.1.164.2.2.1.1 | ||
| A unique value for each SMT. Its value ranges between 1 and the value of snmpFddiSMTNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiSMTStation | 1.3.6.1.4.1.164.2.2.1.2 | ||
| Indicates the Station inside the box to which the current SMT belongs. Its value ranges between 1 and the value of radFddiStationNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiSMTCFState | 1.3.6.1.4.1.164.2.2.1.3 | ||
| The attachement configuration for the Station. Extends the range of values provided by the SNMP variable snmpFddiSMTCFState from the SNMP FDDI MIB. | |||
| OBJECT-TYPE | |||
| INTEGER | isolated(1), localA(2), localB(3), localAB(4), localS(5), wrapA(6), wrapB(7), wrapAB(8), wrapS(9), cWrapA(10), cWrapB(11), cWrapS(12), thru(13) | ||
| radFddiSMTLeftSlot | 1.3.6.1.4.1.164.2.2.1.4 | ||
| Indicates the slot number of the leftmost card on the concentrator implemented inside the box and managed by the agent MAC. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiSMTRightSlot | 1.3.6.1.4.1.164.2.2.1.5 | ||
| Indicates the slot number of the rightmost card on the concentrator implemented inside the box and managed by the agent MAC. Note that the MAC-agent card itself is not taken into consideration. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACTable | 1.3.6.1.4.1.164.2.3 | ||
| A list of FddiMAC entries. The number of entries is given by the value of snmpFddiMACNumber. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadFddiMACEntry | |||
| radFddiMACEntry | 1.3.6.1.4.1.164.2.3.1 | ||
| An entry in table radFddiMACTable. | |||
| OBJECT-TYPE | |||
| RadFddiMACEntry | |||
| radFddiMACSMTIndex | 1.3.6.1.4.1.164.2.3.1.1 | ||
| The value of the SMT index associated with this MAC. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiMACIndex | 1.3.6.1.4.1.164.2.3.1.2 | ||
| A unique value for each MAC. Its value ranges between 1 and the value of snmpFddiMACNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiMACStation | 1.3.6.1.4.1.164.2.3.1.3 | ||
| Indicates the Station inside the box to which the current MAC belongs. Its value ranges between 1 and the value of radFddiStationNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..65535 | ||
| radFddiMACTestResult | 1.3.6.1.4.1.164.2.3.1.4 | ||
| Indicates the result of a test performed on MAC. The value is a sum. It takes the value 0 if the result of the test is OK and if faults occur, 2 raised to a power is added to the sum. The powers are according to the following table: Fault Power cardConfigError 0 GeneralError 1 MACError 2 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACTokenCt | 1.3.6.1.4.1.164.2.3.1.5 | ||
| Token Counts - Refer to ANSI MAC {73}. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radFddiMACRingLoad | 1.3.6.1.4.1.164.2.3.1.6 | ||
| Current traffic value. The traffic is expressed in percents of the maximum FDDI traffic in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACRingLoadBuffer | 1.3.6.1.4.1.164.2.3.1.7 | ||
| Record of traffic for the last second with a resolution of 100 msec. The traffic is expressed in percents of the maximum FDDI traffic and each record contains 10 readings, in the range 1..20, expressed on a log(10) scale ( value = 10*log10(percent) ). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radFddiMACRingLoadTrsh | 1.3.6.1.4.1.164.2.3.1.8 | ||
| Traffic threshold value. When exceeded, a trap is send to the management console. Expressed in percents of the maximum FDDI traffic, in the range 1..20, expressed on a log(10) scale. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACRingLoadPeak | 1.3.6.1.4.1.164.2.3.1.9 | ||
| Maximal traffic value since last reset of hub or relay. Expressed in per- cents of the maximum FDDI traffic, in the range 1..20, expressed on log(10) scale. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACDownstreamNbr | 1.3.6.1.4.1.164.2.3.1.10 | ||
| The MAC's downstream neighbor's long individual MAC address. The value shall be reported as '00 00 00 00 00 00' if it is unknown. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| radFddiMACRingStatus | 1.3.6.1.4.1.164.2.3.1.11 | ||
| Attribute which summs the status of the ring controlled by the current MAC. | |||
| OBJECT-TYPE | |||
| INTEGER | ringUp(1), ringDown(2) | ||
| radFddiMACRingUtilization | 1.3.6.1.4.1.164.2.3.1.12 | ||
| Current traffic value. The traffic is expressed in percents of the maximum FDDI traffic. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiMACRingPeakUtilization | 1.3.6.1.4.1.164.2.3.1.13 | ||
| Peak traffic value since las reset of the hub or relay. The traffic is expressed in percents of the maximum FDDI traffic. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiGroupTable | 1.3.6.1.4.1.164.2.4 | ||
| A list of FddiGroup entries. The number of entries is given by the value of snmpFddiGroupNumber. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadFddiGroupEntry | |||
| radFddiGroupEntry | 1.3.6.1.4.1.164.2.4.1 | ||
| An entry in table radFddiGroupTable. | |||
| OBJECT-TYPE | |||
| RadFddiGroupEntry | |||
| radFddiGroupId | 1.3.6.1.4.1.164.2.4.1.1 | ||
| Unique ID of the group in radFddiGroupTable. Equivalent to slot number in enclosures. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiGroupRedundancy | 1.3.6.1.4.1.164.2.4.1.2 | ||
| This attribute shows the usage of the A/B pair of ports in Tree mode. If the redundancy conditions are not fulfilled, value none(1) will be returned. If backup mode port A is a standby backup of port B, otherwise each of them is connected to a separate bus. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), double-bandwidth(2), backup(3) | ||
| radFddiGroupTopologyMode | 1.3.6.1.4.1.164.2.4.1.3 | ||
| Defines the topology mode of the FDDI PHY card. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), tree(2), ring(3) | ||
| radFddiGroupTestResult | 1.3.6.1.4.1.164.2.4.1.4 | ||
| Result of test performed upon an FDDI group. A value of faulty (1) indicates a CPU or communication at module level. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), faulty(2) | ||
| radFddiGroupConfigStatus | 1.3.6.1.4.1.164.2.4.1.5 | ||
| Indicates the configuration status of the module (group). | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), cardConfigErrorAB(2), cardConfigErrorS(3), switchTopologyError(4) | ||
| radFddiGroupAutoRightLoop | 1.3.6.1.4.1.164.2.4.1.6 | ||
| Value ON of this attribute signifies that a hardware loop was automatically created on a FDDI module which does not sense the existence of another FDDI group on the right hand side. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| radFddiGroupAutoLeftLoop | 1.3.6.1.4.1.164.2.4.1.7 | ||
| Value ON of this attribute signifies that a hardware loop was automatically created on a FDDI module which does not sense the existence of another FDDI group on the left hand side. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| radFddiGroupManRightLoop | 1.3.6.1.4.1.164.2.4.1.8 | ||
| Setting this attribute to ON signifies a command to the hardware to create a loop on the FDDI module which isolates the ring from the right hand side. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| radFddiGroupManLeftLoop | 1.3.6.1.4.1.164.2.4.1.9 | ||
| Setting this attribute to ON signifies a command to the hardware to create a loop on the FDDI module which isolates the ring from the left hand side. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| radFddiGroupOpticalSwitchStatus | 1.3.6.1.4.1.164.2.4.1.10 | ||
| This attribute describes the presence of the optical switch and for existing optical switches describes the possibility of auto-reconfiguration of path resources (MACs and M-ports) in the case of bus fault or connection disabling. If merge(2), resources will try to move to another bus, if non-merge(1) resources are left on their dedicated bus. | |||
| OBJECT-TYPE | |||
| INTEGER | not-present(1), inserted(2), not-inserted(3), present(4) | ||
| radFddiPortTable | 1.3.6.1.4.1.164.2.5 | ||
| . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadFddiPortEntry | |||
| radFddiPortEntry | 1.3.6.1.4.1.164.2.5.1 | ||
| An entry in table radFddiPortTable. | |||
| OBJECT-TYPE | |||
| RadFddiPortEntry | |||
| radFddiPortGroupID | 1.3.6.1.4.1.164.2.5.1.1 | ||
| ID of group to which the FDDI card belongs. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiPortID | 1.3.6.1.4.1.164.2.5.1.2 | ||
| Unique Id of the port in the radFddiPortEntry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiPortTestResult | 1.3.6.1.4.1.164.2.5.1.4 | ||
| Indicates the result of a test performed on a port. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), faulty(2) | ||
| radFddiPortNumberOfConnectedStations | 1.3.6.1.4.1.164.2.5.1.5 | ||
| Number of stations connected to the port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radFddiPortConnectedStations | 1.3.6.1.4.1.164.2.5.1.6 | ||
| This attribute displays the configuration of the stations connected to the port.The FDDI addresses of the stations are displayed in ring order, starting with the address of the first station connected to the port. The length of the string is equal to the value of radFddiPortNumberOfConnectedStations multiplied by 8 (length of FddiSMTStationIdType). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radFddiPortCurrentPath | 1.3.6.1.4.1.164.2.5.1.8 | ||
| Current Path in FDDI port on PHY cards. | |||
| OBJECT-TYPE | |||
| INTEGER | isolated(1), local(2), secondary(3), primary(4), concatenated(5), thru(6) | ||
| radFddiPortFunctionalStatus | 1.3.6.1.4.1.164.2.5.1.9 | ||
| Fubctional status of the port according to value of link error estimate relative to thresholds of alarm and cutoff. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), lerAlarm(2), lerCutoff(3) | ||
| radFddiAgn | 1.3.6.1.4.1.164.2.6 | ||
| OBJECT IDENTIFIER | |||
| radFddiAgnPriSwDesc | 1.3.6.1.4.1.164.2.6.1 | ||
| ASCII string for description and display of the Fddi agent software version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| radWan | 1.3.6.1.4.1.164.3 | ||
| OBJECT IDENTIFIER | |||
| wanGen | 1.3.6.1.4.1.164.3.1 | ||
| OBJECT IDENTIFIER | |||
| chasWanGen | 1.3.6.1.4.1.164.3.1.1 | ||
| OBJECT IDENTIFIER | |||
| chasVersion | 1.3.6.1.4.1.164.3.1.1.1 | ||
| An ASCII string for description and display of the agent chassis version. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| chasTotalNoOfSlt | 1.3.6.1.4.1.164.3.1.1.2 | ||
| This entry indicates the number of physical slots in the chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chasTotalNoOfIoSlt | 1.3.6.1.4.1.164.3.1.1.3 | ||
| This entry indicates the total number of physical IO slots in the chassis, (not all slots hardware should be occupied and active) . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chasTotalNoOfPsSlt | 1.3.6.1.4.1.164.3.1.1.4 | ||
| This entry indicates the number of physical Power Supply slots in the chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chasTotalNoOfClSlt | 1.3.6.1.4.1.164.3.1.1.5 | ||
| This entry indicates the number of physical Common Logic slots in the chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnWanGen | 1.3.6.1.4.1.164.3.1.2 | ||
| OBJECT IDENTIFIER | |||
| statAgnGen | 1.3.6.1.4.1.164.3.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| agnSDateFormat | 1.3.6.1.4.1.164.3.1.2.1.1 | ||
| This entry indicates the date and time format used for the agnSDateAndTimeCmd and for the alarm history report. | |||
| OBJECT-TYPE | |||
| INTEGER | ddMMYYYY(1), mmDDYYYY(2), yyyyDDMM(3), yyyyMMDD(4) | ||
| agnSDateCmd | 1.3.6.1.4.1.164.3.1.2.1.2 | ||
| This entry indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSTimeCmd | 1.3.6.1.4.1.164.3.1.2.1.3 | ||
| This entry indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSActiveCnfg | 1.3.6.1.4.1.164.3.1.2.1.4 | ||
| This entry specifies the unique identifier of the configuration, that is currently active and running. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSEditCnfg | 1.3.6.1.4.1.164.3.1.2.1.5 | ||
| This entry indicates the unique identifier of the configuration that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSLastCnfgFlipTime | 1.3.6.1.4.1.164.3.1.2.1.6 | ||
| This entry indicates the Date & Time of the last flip to the current configuration at the agent. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSLastCnfgFlipCause | 1.3.6.1.4.1.164.3.1.2.1.7 | ||
| This entry describes the flip's cause. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSEditBy | 1.3.6.1.4.1.164.3.1.2.1.8 | ||
| This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after an update(load) operation. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), snmp(2), terCon1(3), terCon2(4), terInbandCon1(5), terInbandCon2(6), lcd(7) | ||
| agnSClkSrc | 1.3.6.1.4.1.164.3.1.2.1.9 | ||
| This entry indicates the source of the system clock. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), fallback(2), internal(3) | ||
| agnSAlrStatus | 1.3.6.1.4.1.164.3.1.2.1.10 | ||
| Indicates the alarm state in the agent level, i.e. lower level (card/port) alarms not included. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnSAlrStatusAll | 1.3.6.1.4.1.164.3.1.2.1.11 | ||
| Indicates the alarm state of the entire agent, i.e. including card and port alarms status. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnSMaskedAlrStat | 1.3.6.1.4.1.164.3.1.2.1.12 | ||
| Indicates the alarm state in the agent level,[ i.e. lower level (card/port) alarms not included] including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnSMaskedAlrStatAll | 1.3.6.1.4.1.164.3.1.2.1.13 | ||
| Indicates the alarm state of the entire agent, i.e. including card and port alarms status,including Masked alarms. critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnSTstStatAll | 1.3.6.1.4.1.164.3.1.2.1.14 | ||
| on(3) - when there is at least one test in progress in one of the agent cards, otherwise the value will be off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSAlrTable | 1.3.6.1.4.1.164.3.1.2.1.15 | ||
| List of agent related alarms and indications for alarms at system level. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSAlrEntry | |||
| agnSAlrEntry | 1.3.6.1.4.1.164.3.1.2.1.15.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSAlrEntry | |||
| agnSAlrIdx | 1.3.6.1.4.1.164.3.1.2.1.15.1.1 | ||
| A unique number to identify an entry in the alarm status table of the agent. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSAlrCodeDescription | 1.3.6.1.4.1.164.3.1.2.1.15.1.2 | ||
| This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSAlrCode | 1.3.6.1.4.1.164.3.1.2.1.15.1.3 | ||
| A code identifying the alarm of an entry in the alarm status table at system level. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSAlrSeverity | 1.3.6.1.4.1.164.3.1.2.1.15.1.4 | ||
| The severity of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnSAlrState | 1.3.6.1.4.1.164.3.1.2.1.15.1.5 | ||
| State of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSAlrCounter | 1.3.6.1.4.1.164.3.1.2.1.15.1.6 | ||
| A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSAlrMask | 1.3.6.1.4.1.164.3.1.2.1.15.1.7 | ||
| Alarm mask : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSAlrInvert | 1.3.6.1.4.1.164.3.1.2.1.15.1.8 | ||
| Alarm invert : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSClearAlrCmd | 1.3.6.1.4.1.164.3.1.2.1.16 | ||
| Setting this attribute to ON, enforce a clear operation on all the agent(general) events. General alarms are alarms which are not specific to a card or port. The clear operation will not be applied for masked/inverted alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSClearAllAlrCmd | 1.3.6.1.4.1.164.3.1.2.1.17 | ||
| Setting this attribute to ON, enforce a clear operation on all MUX alarm events at the levels of agent, slots and ports. The clear operation will not be applied for masked/inverted alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnSSanityCheckStatus | 1.3.6.1.4.1.164.3.1.2.1.18 | ||
| Upon completion of the Sanity check process on the TmpCnfg this attribute will be set to: FAIL(2) - when there is at least one error encountered and possibly some warnings. WARNING(3) - when there are only warnings. otherwise, the value will be OK(4). The value will be UNKNOWN(1) if changes were made in the TmpCnfg following the last Sanity check. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), fail(2), warning(3), ok(4) | ||
| agnSNoOfSanityCheckErr | 1.3.6.1.4.1.164.3.1.2.1.19 | ||
| This entry indicates the number of errors/warnings discovered by the last SanityCheck process. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSErrListTable | 1.3.6.1.4.1.164.3.1.2.1.20 | ||
| List of errors and warnings found during Sanity Check process. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSErrListEntry | |||
| agnSErrListEntry | 1.3.6.1.4.1.164.3.1.2.1.20.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSErrListEntry | |||
| agnSErrIdx | 1.3.6.1.4.1.164.3.1.2.1.20.1.1 | ||
| Unique number to identify an entry in the error list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSErrDescription | 1.3.6.1.4.1.164.3.1.2.1.20.1.2 | ||
| This attribute is a full text description of the sanity check error including error code, slot and port numbers related to the code . | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnSMaxNoOfCnfg | 1.3.6.1.4.1.164.3.1.2.1.21 | ||
| Maximum number of configurations that can be defined and stored in the MUX. If the mux has a large capacity, the maximum will be limited to 254. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSCnfgTable | 1.3.6.1.4.1.164.3.1.2.1.22 | ||
| This table contains an entry per configuration. It indicates if the configuration is valid. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSCnfgEntry | |||
| agnSCnfgEntry | 1.3.6.1.4.1.164.3.1.2.1.22.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSCnfgEntry | |||
| agnSEntryIdx | 1.3.6.1.4.1.164.3.1.2.1.22.1.1 | ||
| Unique number to identify an entry in the configuration table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSEntryIsValid | 1.3.6.1.4.1.164.3.1.2.1.22.1.2 | ||
| This attribute indicates whether the specific configuration is valid in the MUX . Value of NO indicates: no such configuration in the MUX. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| cnfgAgnGen | 1.3.6.1.4.1.164.3.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| agnCSanityCheckCmd | 1.3.6.1.4.1.164.3.1.2.2.1 | ||
| Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion the value will automatically be changed to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnCSaveCnfgIdxCmd | 1.3.6.1.4.1.164.3.1.2.2.2 | ||
| This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| agnCLoadCnfgIdxCmd | 1.3.6.1.4.1.164.3.1.2.2.3 | ||
| This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on Valid configurations (agnSEntryIsValid) | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| agnCClkSrcTable | 1.3.6.1.4.1.164.3.1.2.2.4 | ||
| All the entries of this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCClkSrcEntry | |||
| agnCClkSrcEntry | 1.3.6.1.4.1.164.3.1.2.2.4.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCClkSrcEntry | |||
| agnCClkCnfgIdx | 1.3.6.1.4.1.164.3.1.2.2.4.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..100) being accessed and Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnCClkSrcIdx | 1.3.6.1.4.1.164.3.1.2.2.4.1.2 | ||
| An index to the table. There are only two entries to this table. Index 1 points to the Master clock parameters and Index 2 points to the Fallback clock parameters | |||
| OBJECT-TYPE | |||
| Integer32 | 1..2 | ||
| agnCClkSrcMode | 1.3.6.1.4.1.164.3.1.2.2.4.1.3 | ||
| The source of the nodal timing. | |||
| OBJECT-TYPE | |||
| INTEGER | internal(1), rxClk(2), adaptive(3) | ||
| agnCClkSrcSlt | 1.3.6.1.4.1.164.3.1.2.2.4.1.4 | ||
| This entry is valid only when we are working in rxClk mode. For an invalid entry, the return value will be '7fff'h. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| agnCClkSrcPrt | 1.3.6.1.4.1.164.3.1.2.2.4.1.5 | ||
| This entry is valid only when we are working in rxClk or adaptive mode. For an invalid entry, the return value will be '7fff'h. - For rxClk mode, the values can be: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , notApplicable (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) - For adaptive mode, the value will be the ifIndex of the selected IP Bundle. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCDeleteCnfgIdxCmd | 1.3.6.1.4.1.164.3.1.2.2.5 | ||
| Setting this attribute will delete the requested DB from the NVRAM . | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| agnCDefaultCnfgIdxCmd | 1.3.6.1.4.1.164.3.1.2.2.6 | ||
| Setting this attribute will define the desired working configuration when no conditions of the Flip DB Table are fulfilled and no Net GO command was issued. This command will be accepted only if the Configuration number exists (agnSEntryIsValid=yes). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| agnCnfgDataTable | 1.3.6.1.4.1.164.3.1.2.2.7 | ||
| This table contains data about the agent configurations. The table will support only data about valid configurations of the agent. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCnfgDataEntry | |||
| agnCnfgDataEntry | 1.3.6.1.4.1.164.3.1.2.2.7.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCnfgDataEntry | |||
| agnCnfgIdx | 1.3.6.1.4.1.164.3.1.2.2.7.1.1 | ||
| This object indicates the Idx of the agent' Cnfg the following objects refer. 255=Temporary Cnfg (Set is done only to this configuration). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnCnfgDesc | 1.3.6.1.4.1.164.3.1.2.2.7.1.2 | ||
| This object is a description of the Configuration, entered by user, to enhance Cnfg recognition. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..30) | ||
| agnCnfgUpdDate | 1.3.6.1.4.1.164.3.1.2.2.7.1.3 | ||
| This object indicates the date when last update of this configuration was performed, as it is known by the agent using its own real-time clock. The format would be as specified by the agnSDateFormat. When update is performed, the agent should save the date. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnCnfgUpdTime | 1.3.6.1.4.1.164.3.1.2.2.7.1.4 | ||
| This object indicates the time when last update of this configuration was performed, as it is known by the agent using its own real-time clock. When update is performed, the agent should save the time. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnCnfgUpdMnger | 1.3.6.1.4.1.164.3.1.2.2.7.1.5 | ||
| This object indicates the IP Address of the Manager who performed the last update of this configuration. When update is performed, the agent should save the IP Address of the Manager who commanded the update. That will enable a manager to know if he performed the last update, or another manager did. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| agnCnfgAlarm | 1.3.6.1.4.1.164.3.1.2.2.8 | ||
| OBJECT IDENTIFIER | |||
| agnCnfgAlrFilterWindow | 1.3.6.1.4.1.164.3.1.2.2.8.1 | ||
| Window of time, in seconds. During this Window, the alarms filter is performed. Same Window for all agent alarms that need filtering. Upon end of the Window, the state of the alarm is updated and a new Window starts. If no alarm needs filtering, this object's value will not be used. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| agnCnfgAlrTable | 1.3.6.1.4.1.164.3.1.2.2.8.2 | ||
| This table enables the user to set attributes to each alarm. Setting for a non-existing entry agnCnfgAlrMask, agnCnfgAlrInvert or agnCnfgAlrFilter to 'yes'(or yesAndSave for Mask) will add this new entry to the table. Setting for an existing entry agnCnfgAlrMask/ agnCnfgAlrInvert/agnCnfgAlrFilter (one or more) to 'no' (noAndSave for Mask) so that ALL these objects' values are 'no' , will delete this entry from the table. For agnCnfgAlrMask, only if [(last saved value=noAndSave) AND (new value is 'no' or 'noAndSave')] the object's value is considered 'no' for deleting the entry. For some products (like MP, MPH, Vmux2100) the Active Alarms are always part of the table and cannot be removed even if their Mask/Invert/Filter are No. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCnfgAlrEntry | |||
| agnCnfgAlrEntry | 1.3.6.1.4.1.164.3.1.2.2.8.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCnfgAlrEntry | |||
| agnCnfgAlrCode | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.1 | ||
| The alarm code. The following attributes refer this code. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCnfgAlrSlot | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.2 | ||
| The alarm slot. The following attributes apply for the alarm code and slot selected. all = the attributes apply to all slots. notApplicable = the selected alarm is for system level. For the Vmux2100 Main Board clA (3) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), all(200), notApplicable(255) | ||
| agnCnfgAlrPort | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.3 | ||
| The alarm port. The following attributes apply for the alarm code,slot and port selected. 200 = all = the attributes apply to all ports of the selected slot. When selected Slot is 'all', only 'all' or 'notApplicable' are valid Port selections. notApplicable = the selected alarm is for system or card level. =255 for MP =100 for DXC - For MP: - valid cards' ports are: exPrt1(1)..exPrt16(16) inPrt1(101)..inPrt48 (148) - IP Bundles - For DXC, the port index will include the Slot, as for all DXC tables: [(IO Slot+10)&n] ; n=odd for external ports n=even for internal ports. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCnfgAlrMask | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.4 | ||
| An attribute defining the desired Mask state of an alarm . no - unmask (this command is not saved in agent's common database) noAndSave - unmask ; this command is saved in agent's common database yes - mask (this command is not saved in agent's common database) yesAndSave - mask ; this command is saved in agent's common database. Commands that are not saved, will be lost upon power-up or selected card removal. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), noAndSave(2), yes(3), yesAndSave(4) | ||
| agnCnfgAlrInvert | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.5 | ||
| An attribute defining the desired Invert state of an alarm . no - not inverted. yes - inverted. For MP, it is not applicable for alarms that are currently OFF. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnCnfgAlrFilter | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.6 | ||
| An attribute defining if Filter is desired for the alarm . no - no filter. yes - filter activate. This filter is activated within a window of time defined by agnCnfgAlrFilterWindow. Its purpose is to avoid frequent changes of an alarm between ON/OFF states. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnCnfgAlrFilterSet | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.7 | ||
| This is a top threshold causing the alarm that passes it, to be declared Set (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at least, during the window in order to be considered ON. The maximum value will be 255. This value should be greater than the one of agnCnfgAlrFilterReset. Agents that do not support Alarms Filter, will return 0. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCnfgAlrFilterReset | 1.3.6.1.4.1.164.3.1.2.2.8.2.1.8 | ||
| This is a bottom threshold causing the alarm that does not pass it, to be declared Reset (ON) at the end of the respective window of time. - For alarms defined by default as state alarms (minor,major) this value will be in [%]. - For alarms defined by default as events, this value will be an integer meaning how many times this event should appear at most, during the window, in order to be considered OFF. This value should be less than the one of agnCnfgAlrFilterSet. Agents that do not support Alarms Filter, will return 0. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCnfgAlrReportTable | 1.3.6.1.4.1.164.3.1.2.2.8.3 | ||
| This table enables the user to configure the desired Alarm Reports according to alarms severity. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCnfgAlrReportEntry | |||
| agnCnfgAlrReportEntry | 1.3.6.1.4.1.164.3.1.2.2.8.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCnfgAlrReportEntry | |||
| agnCnfgAlrReportType | 1.3.6.1.4.1.164.3.1.2.2.8.3.1.1 | ||
| The alarm report type. trap - traps will be sent only for alarms having the selected On/Off severity or higher. buffer - only alarms having the selected On/Off severity and higher, will be reported to the buffer. relay - relay contact will be activated only for alarms having the selected On severity or higher. For products having 2 relays, this is the R1 Relay. alrLedOn/alrLedBlink - user should select a higher severity (ReportOn) for alrLedBlink than for alrLedOn (Blinking Led means a more severe alarm than steady ON Led). alrLedOn - MTCL-1 Alarm Led will be ON only when agnSAlrStatusAll equals the selected severity or higher, but lower severity than that selected for 'alrLedBlink'. For products having 2 LEDs, this is the Minor LED. alrLedBlink - MTCL-1 Alarm Led will Blink only when agnSAlrStatusAll equals the selected severity or higher. For products having 2 LEDs, this is the Major LED. relay2 - relay 2 contact will be activated only for alarms having the selected On severity or higher. This is the R2 Relay. | |||
| OBJECT-TYPE | |||
| INTEGER | trap(1), buffer(2), relay(3), alrLedOn(4), alrLedBlink(5), relay2(6) | ||
| agnCnfgAlrStartReportOn | 1.3.6.1.4.1.164.3.1.2.2.8.3.1.2 | ||
| This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to ON state. noReport - no Report at all (for any severity). | |||
| OBJECT-TYPE | |||
| INTEGER | noReport(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnCnfgAlrStartReportOff | 1.3.6.1.4.1.164.3.1.2.2.8.3.1.3 | ||
| This object specifies the severity from which alarms will be reported. Alarms having this severity or higher, will be reported. This object specifies the report severity only for alarms that turn to OFF state. notApplicable - for 'relay','alrLedOn','alrLedBlink', 'relay2' report types, in MP. noReport - no Report at all (for any severity). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), noReport(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnCOffsetCmd | 1.3.6.1.4.1.164.3.1.2.2.9 | ||
| An object defining special user request. notApplicable - is RO value for products that do not support this object. normal - nothing special u1 - user 1 - for all Voice cards, the DISPLAYED Tx and Rx Levels will have the following Offsets: - 2 Wires port: Tx Level: the base value (for 0dBm) = 0 Rx Level: the base value (for 0dBm) = -2 - 4 Wires port: Tx Level: the base value (for 0dBm) = -16 Rx Level: the base value (for 0dBm) = 7 The MIB and application DB will use the values without Offset. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), normal(2), u1(3) | ||
| agnCT1E1RingTable | 1.3.6.1.4.1.164.3.1.2.2.10 | ||
| Configuration of all T1/E1 Ring ML cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that does not participate in the T1/E1 Ring, will not exist in this table. A ML port that exists in this table, cannot exist at the same time in the IO Redundancy table (sysCRdnTable). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCT1E1RingEntry | |||
| agnCT1E1RingEntry | 1.3.6.1.4.1.164.3.1.2.2.10.1 | ||
| An Entry in table agnCT1E1RingTable | |||
| OBJECT-TYPE | |||
| AgnCT1E1RingEntry | |||
| agnCT1E1RingCnfgIdx | 1.3.6.1.4.1.164.3.1.2.2.10.1.1 | ||
| This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCT1E1RingPrimeSlot | 1.3.6.1.4.1.164.3.1.2.2.10.1.2 | ||
| The slot number of the Primary card of the Ring Pair. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| agnCT1E1RingPrimePort | 1.3.6.1.4.1.164.3.1.2.2.10.1.3 | ||
| The port number in the Primary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCT1E1RingSecSlot | 1.3.6.1.4.1.164.3.1.2.2.10.1.4 | ||
| The slot number of the Secondary card of the Ring Pair. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| agnCT1E1RingSecPort | 1.3.6.1.4.1.164.3.1.2.2.10.1.5 | ||
| The port number in the Secondary Card. For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCT1E1RingRecTime | 1.3.6.1.4.1.164.3.1.2.2.10.1.6 | ||
| T1/E1 Ring Recovery Time (sec). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| agnCT1E1RingRowStatus | 1.3.6.1.4.1.164.3.1.2.2.10.1.7 | ||
| This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| cmprAgnGen | 1.3.6.1.4.1.164.3.1.2.3 | ||
| OBJECT IDENTIFIER | |||
| agnCmprTable | 1.3.6.1.4.1.164.3.1.2.3.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCmprEntry | |||
| agnCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCmprEntry | |||
| agnCmprTypIdx | 1.3.6.1.4.1.164.3.1.2.3.1.1.1 | ||
| This attribute indicates the Type of the Compressed being referred. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.2.3.1.1.2 | ||
| This attribute indicates the configuration to which the Compressed information is related. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCmprVersion | 1.3.6.1.4.1.164.3.1.2.3.1.1.3 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCmprObj | 1.3.6.1.4.1.164.3.1.2.3.1.1.4 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnDlciCmprTable | 1.3.6.1.4.1.164.3.1.2.3.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnDlciCmprEntry | |||
| agnDlciCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnDlciCmprEntry | |||
| agnDlciCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.2.3.2.1.1 | ||
| This attribute indicates the configuration to which the Compressed information is related. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnDlciCmprVersion | 1.3.6.1.4.1.164.3.1.2.3.2.1.2 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnDlciCmprDlciIdx | 1.3.6.1.4.1.164.3.1.2.3.2.1.3 | ||
| This attribute indicates a unique identifier of the Dlci, the compressed information relates to. The values are between 16 - 991. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnDlciCmprObj | 1.3.6.1.4.1.164.3.1.2.3.2.1.4 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnAlarmsCmprTable | 1.3.6.1.4.1.164.3.1.2.3.3 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnAlarmsCmprEntry | |||
| agnAlarmsCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnAlarmsCmprEntry | |||
| agnAlarmsCmprVersion | 1.3.6.1.4.1.164.3.1.2.3.3.1.1 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnAlarmsCmprAlarmIdx | 1.3.6.1.4.1.164.3.1.2.3.3.1.2 | ||
| A unique number to identify an entry in the alarm status table of the agent. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnAlarmsCmprObj | 1.3.6.1.4.1.164.3.1.2.3.3.1.3 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnAlrBufCmprTable | 1.3.6.1.4.1.164.3.1.2.3.4 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnAlrBufCmprEntry | |||
| agnAlrBufCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.4.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnAlrBufCmprEntry | |||
| agnAlrBufCmprVersion | 1.3.6.1.4.1.164.3.1.2.3.4.1.1 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnAlrBufCmprAlarmIdx | 1.3.6.1.4.1.164.3.1.2.3.4.1.2 | ||
| A unique number to identify an entry in the history alarms buffer of the agent. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnAlrBufCmprObj | 1.3.6.1.4.1.164.3.1.2.3.4.1.3 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnSCmprErrListTable | 1.3.6.1.4.1.164.3.1.2.3.5 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSCmprErrListEntry | |||
| agnSCmprErrListEntry | 1.3.6.1.4.1.164.3.1.2.3.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSCmprErrListEntry | |||
| agnSCmprErrVersion | 1.3.6.1.4.1.164.3.1.2.3.5.1.1 | ||
| The version of the compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSCmprErrIdx | 1.3.6.1.4.1.164.3.1.2.3.5.1.2 | ||
| Unique number to identify an entry in the errors list table. The maximum entry value cannot exceed the value of 'agnSNoOfSanityCheckErr'. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnSCmprErrObj | 1.3.6.1.4.1.164.3.1.2.3.5.1.3 | ||
| This attribute is a full text description of the error, including: error code, slot and port numbers related to the code . | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnTsCmprTable | 1.3.6.1.4.1.164.3.1.2.3.6 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnTsCmprEntry | |||
| agnTsCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.6.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnTsCmprEntry | |||
| agnTsCmprVerIdx | 1.3.6.1.4.1.164.3.1.2.3.6.1.1 | ||
| This object indicates the version of the internal format of the Compressed data. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.2.3.6.1.2 | ||
| This object indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsCmprSlotIdx | 1.3.6.1.4.1.164.3.1.2.3.6.1.3 | ||
| This object indicates the Slot to which the Compressed information is related. For MP-2100: IO-1..IO-12 = (5).. (16) For DXC-30 : IO-1..IO-15 = (5).. (19). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsCmprPortIdx | 1.3.6.1.4.1.164.3.1.2.3.6.1.4 | ||
| This object indicates the Port within the Slot, to which the Compressed information is related. For Port Index see each product's spec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsCmprPduIdx | 1.3.6.1.4.1.164.3.1.2.3.6.1.5 | ||
| This object indicates the PDU index within the same port. That provides for the case when one PDU is not sufficient for all TS Assignment data of the same port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsCmprData | 1.3.6.1.4.1.164.3.1.2.3.6.1.6 | ||
| This object is the compressed information itself. It provides information about all TSs of a port. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnXCmprTable | 1.3.6.1.4.1.164.3.1.2.3.7 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnXCmprEntry | |||
| agnXCmprEntry | 1.3.6.1.4.1.164.3.1.2.3.7.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnXCmprEntry | |||
| agnXCmprTypIdx | 1.3.6.1.4.1.164.3.1.2.3.7.1.1 | ||
| This attribute indicates the Type of the Compressed being referred. One of the types is V5.1 Variant data. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprVersion | 1.3.6.1.4.1.164.3.1.2.3.7.1.2 | ||
| This attribute indicates the version of the internal format of the Compressed data. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprIdx3 | 1.3.6.1.4.1.164.3.1.2.3.7.1.3 | ||
| 3rd index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant, this attribute indicates the configuration to which the Compressed information is related. 255=temporary configuration. Set can be performed only to the temporary configuration. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprIdx4 | 1.3.6.1.4.1.164.3.1.2.3.7.1.4 | ||
| 4th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique number of the slot position where the card is inserted. Valid values: psA(1),psB(2),clA(3),clB(4),io1(5)..io12(16); notApplicable=255. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprIdx5 | 1.3.6.1.4.1.164.3.1.2.3.7.1.5 | ||
| 5th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt12 (12) , inPrt1 (101) .. inPrt48 (148). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprIdx6 | 1.3.6.1.4.1.164.3.1.2.3.7.1.6 | ||
| 6th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute indicates the Variant index. Valid values are: 0..127, 255 (= temp cnfg).Set can be performed only to the temporary configuration. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprIdx7 | 1.3.6.1.4.1.164.3.1.2.3.7.1.7 | ||
| 7th index - can be used for any purpose according to the agnXCmprTypIdx. Example: for V5.1 Variant,this attribute is not needed. Therefore, its value will be always 255=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnXCmprObj | 1.3.6.1.4.1.164.3.1.2.3.7.1.8 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| alrBuffGen | 1.3.6.1.4.1.164.3.1.2.4 | ||
| OBJECT IDENTIFIER | |||
| alrBufTable | 1.3.6.1.4.1.164.3.1.2.4.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlrBufEntry | |||
| alrBufEntry | 1.3.6.1.4.1.164.3.1.2.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AlrBufEntry | |||
| alrBufIdx | 1.3.6.1.4.1.164.3.1.2.4.1.1.1 | ||
| This attribute indicates a unique number to identify this entry | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| alrBufDescription | 1.3.6.1.4.1.164.3.1.2.4.1.1.2 | ||
| This entry is a unique text description of the alarm in the buffer. The alarm description includes the following information: alarm code, slot id, card type, channel id , alarm text, alarm status, masked flag and event counter | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnFlipDb | 1.3.6.1.4.1.164.3.1.2.5 | ||
| OBJECT IDENTIFIER | |||
| agnCAgendaTable | 1.3.6.1.4.1.164.3.1.2.5.1 | ||
| This table devides the week days into categories needed for DB flip consideration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCAgendaEntry | |||
| agnCAgendaEntry | 1.3.6.1.4.1.164.3.1.2.5.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCAgendaEntry | |||
| agnCAgendaCnfgIdx | 1.3.6.1.4.1.164.3.1.2.5.1.1.1 | ||
| Active or Temporary Agenda Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnCAgendaDayIdx | 1.3.6.1.4.1.164.3.1.2.5.1.1.2 | ||
| Day of week | |||
| OBJECT-TYPE | |||
| INTEGER | sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7) | ||
| agnCAgendaDayCategory | 1.3.6.1.4.1.164.3.1.2.5.1.1.3 | ||
| The Category of the Day | |||
| OBJECT-TYPE | |||
| INTEGER | fullWorkday(1), partialWorkday(2), weekend(3) | ||
| agnCFlipNetEventsTable | 1.3.6.1.4.1.164.3.1.2.5.2 | ||
| This table holds the Net Events the MUX should trace | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCFlipNetEventsEntry | |||
| agnCFlipNetEventsEntry | 1.3.6.1.4.1.164.3.1.2.5.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCFlipNetEventsEntry | |||
| agnCFlipNetEventsCnfgIdx | 1.3.6.1.4.1.164.3.1.2.5.2.1.1 | ||
| Active or Temporary Net Events Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnCFlipNetEventIdx | 1.3.6.1.4.1.164.3.1.2.5.2.1.2 | ||
| Entry within the table | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| agnCFlipNetEventActive | 1.3.6.1.4.1.164.3.1.2.5.2.1.3 | ||
| Indicates if the entry is valid. In order to Add/Modify parameters of an entry, this object should be set to Yes. In order to delete an entry, this object should be Set to No. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnCFlipNetEventType | 1.3.6.1.4.1.164.3.1.2.5.2.1.4 | ||
| The Net Event type | |||
| OBJECT-TYPE | |||
| INTEGER | time(1), linkDown(2), congestion(3) | ||
| agnCFlipNetEventNo | 1.3.6.1.4.1.164.3.1.2.5.2.1.5 | ||
| The Net Event No. (Bit Index) | |||
| OBJECT-TYPE | |||
| Integer32 | 1..512 | ||
| agnCFlipNetEventSlot | 1.3.6.1.4.1.164.3.1.2.5.2.1.6 | ||
| The slot to which the net event relates . Not applicable for time event | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| agnCFlipNetEventPort | 1.3.6.1.4.1.164.3.1.2.5.2.1.7 | ||
| The port within the relevant slot. Valid values: - extPrt1(1)..exPrt16(16) - notApplicable(100) - inPrt1(101)..inPrt48(148) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnCFlipNetEventISD | 1.3.6.1.4.1.164.3.1.2.5.2.1.8 | ||
| The time in seconds since the Net Event was reported as ON until it is considered as ON. Not relevant for time events. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..999 | ||
| agnCFlipNetEventOSD | 1.3.6.1.4.1.164.3.1.2.5.2.1.9 | ||
| The time in seconds since the net event was reported as OFF until it is considered as OFF. Not relevant for time events. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..999 | ||
| agnCFlipNetEventDayType | 1.3.6.1.4.1.164.3.1.2.5.2.1.10 | ||
| The time event relates to all days defined in this category in the agnCAgendaTable. Applicable only for time event | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), fullWorkday(2), partialWorkday(3), weekend(4) | ||
| agnCFlipNetEventStartTime | 1.3.6.1.4.1.164.3.1.2.5.2.1.11 | ||
| The time event will be activated at this time. The format is hh:mm. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(5) | ||
| agnCFlipNetEventEndTime | 1.3.6.1.4.1.164.3.1.2.5.2.1.12 | ||
| The time event will be deactivated at this time. The format is hh:mm. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(5) | ||
| agnCFlipTable | 1.3.6.1.4.1.164.3.1.2.5.3 | ||
| The DB Flip Decisions Table | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnCFlipEntry | |||
| agnCFlipEntry | 1.3.6.1.4.1.164.3.1.2.5.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnCFlipEntry | |||
| agnCFlipCnfgIdx | 1.3.6.1.4.1.164.3.1.2.5.3.1.1 | ||
| Active or Temporary Flip Decisions Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnCFlipIdx | 1.3.6.1.4.1.164.3.1.2.5.3.1.2 | ||
| Entry number within the table | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| agnCFlipActive | 1.3.6.1.4.1.164.3.1.2.5.3.1.3 | ||
| Indicates if the entry is valid. In order to Add/Modify parameters of an entry this object should be Set to Yes. In order to delete an entry, this object should be Set to No. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnCFlipLogicalExp | 1.3.6.1.4.1.164.3.1.2.5.3.1.4 | ||
| A logical expression composed of events numbers (which were configured in the 'AgnCFlipNetEvantsTable') and logical operators ('|', '&', '!', '(', ')') between them. e.g - (1 & !2) | (121 & 230) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..20) | ||
| agnCFlipDbNo | 1.3.6.1.4.1.164.3.1.2.5.3.1.5 | ||
| The ID of the required DB | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| agnCFlipDiscardDe | 1.3.6.1.4.1.164.3.1.2.5.3.1.6 | ||
| Indicates whether the Mux should start discarding all DE. (MP3000 Only). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| agnFlipDbControls | 1.3.6.1.4.1.164.3.1.2.5.4 | ||
| OBJECT IDENTIFIER | |||
| agnCFlipDbSanityCheckCmd | 1.3.6.1.4.1.164.3.1.2.5.4.1 | ||
| Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and automatically be changed to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnCSaveFlipDbCmd | 1.3.6.1.4.1.164.3.1.2.5.4.2 | ||
| Setting this attribute to on(3) will initiate the process of Sanity check on the Temp Flip Db and if it is OK, it will save the Flip Db in the NVRAM, activating the new Flip DB . If check detects errors, the save will not be performed. Afterwards, the object's value will change automatically to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnCSaveNetCnfgIdxCmd | 1.3.6.1.4.1.164.3.1.2.5.4.3 | ||
| This attribute specifies the Id of the target NVRAM Cnfg to which the TmpCnfg should be transferred. Upon set command the MUX will initiate the Sanity-Check process first. If successful, the actual transfer will be performed. If warnings are detected, the user will have to perform the command again to confirm the operation. Setting this object a second time to the same value without performing any change in the database, will cause the result: agnSSanityCheckStatus = unknown. This attribute doesn't cause actual Flip. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| agnCSaveNetFlipDbCmd | 1.3.6.1.4.1.164.3.1.2.5.4.4 | ||
| Setting this attribute to on(3) will save the Temp Flip DB Into the NVRAM without actual flip. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnCNetGoCmd | 1.3.6.1.4.1.164.3.1.2.5.4.5 | ||
| Setting this attribute to On will broadcast a 'GO' command to the network. When a Mux receives a 'GO' command it issues a delay for 'agnCNetDelay' seconds and then activates the DB which was pre-defined by one of the commands : 'agnCSaveNetCnfgIdxCmd' or 'agnCSaveNetFlipDbCmd'. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnCNetDelay | 1.3.6.1.4.1.164.3.1.2.5.4.6 | ||
| This attribute determines the period of time in seconds that takes for a message to be transferred over all the network. After a 'GO' command the MUX issues a delay of 'agnCNetDelay' before activating the appropriate DB. The delay will be applied only after performing agnCSaveFlipDbCmd. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..999 | ||
| agnCNetEventsBcast | 1.3.6.1.4.1.164.3.1.2.5.4.7 | ||
| This object determines if the Net Events will be Broadcasted to other Muxes of the Net or not. disabled - Net Events will NOT be Broadcasted enabled - Net Events will be Broadcasted. Default=disabled. The value will be applied only after performing agnCSaveFlipDbCmd. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(2), enabled(3) | ||
| agnCNetEventsBcastInterval | 1.3.6.1.4.1.164.3.1.2.5.4.8 | ||
| When agnCNetEventsBcast is enabled, this object determines the interval of time in seconds, between two consecutive Net Events transferred over the network. Default=40 sec. The interval will be applied only after performing agnCSaveFlipDbCmd. | |||
| OBJECT-TYPE | |||
| Integer32 | 10..60 | ||
| agnSa | 1.3.6.1.4.1.164.3.1.2.6 | ||
| OBJECT IDENTIFIER | |||
| agnSaSwchStatus | 1.3.6.1.4.1.164.3.1.2.6.1 | ||
| This object indicates the status of the switches on the stand-alone unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits: bit 0 NMS (LSB) bit 1 Terminal '1' = forces the DCE to be terminal with Rate=9600bps, Data bits=8, Stop bits=1 bit 2 Xray bit 3 SW-Load '1' = when SW is loaded bit 4 DBS Default of all bits=0 When the status of these switches is unknown, the value of this object is 255. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnListDecoding | 1.3.6.1.4.1.164.3.1.2.7 | ||
| OBJECT IDENTIFIER | |||
| agnListDecodingTable | 1.3.6.1.4.1.164.3.1.2.7.1 | ||
| A decoding table . For each type of list, a description is given for each existing code. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnListDecodingEntry | |||
| agnListDecodingEntry | 1.3.6.1.4.1.164.3.1.2.7.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnListDecodingEntry | |||
| agnListDecodingType | 1.3.6.1.4.1.164.3.1.2.7.1.1.1 | ||
| The type of list the decoding data refers to. alr - Alarms list sanity - Sanity Check Error list. | |||
| OBJECT-TYPE | |||
| INTEGER | alr(1), sanity(2) | ||
| agnListDecodingCode | 1.3.6.1.4.1.164.3.1.2.7.1.1.2 | ||
| The specific code for which decoding is needed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnListDecodingDescription | 1.3.6.1.4.1.164.3.1.2.7.1.1.3 | ||
| The description fitting the specific code and type of list required. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| agnListDecodingDefState | 1.3.6.1.4.1.164.3.1.2.7.1.1.4 | ||
| This object is applicable only for agnListDecodingType=alr. It reports the default state/severity of each alarm. User can change the severity of the alarms defined by this default via the agnListDecodingSeverity object. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnListDecodingSeverity | 1.3.6.1.4.1.164.3.1.2.7.1.1.5 | ||
| This object is applicable only for agnListDecodingType=alr. It enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). event - can be set only for an alarm that is defined by default as 'event'. User can change the severity of the alarms defined by default as minor or major. The severity of an event may be set to another severity, but the change will actually happen only if the event threshold is active and passed the Set/ON condition. An event alarm that passed the threshold and changed its severity, will return automatically to event severity when meeting its Reset/OFF condition. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7) | ||
| agnListDecodingAcmRelaySlt | 1.3.6.1.4.1.164.3.1.2.7.1.1.6 | ||
| This object indicates the ACM slot, desired for outbound relay (report) for the selected alarm. In the ?004 Unit the entries io6(10)..io12(16) are not valid. none - when agnListDecodingType=alr AND the selected alarm should not be reported by an ACM card. notApplicable - when agnListDecodingType=sanity OR when [agnListDecodingType=alr and there is no ACM card installed in the Mux]. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| agnListDecodingAcmRelayPrt | 1.3.6.1.4.1.164.3.1.2.7.1.1.7 | ||
| This object indicates the ACM port within the slot, desired for outbound relay (report) for the selected alarm. notApplicable - when agnListDecodingType=sanity OR when agnListDecodingAcmRelaySlt=notApplicable. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), notApplicable(255) | ||
| agnSystemDlci | 1.3.6.1.4.1.164.3.1.2.8 | ||
| OBJECT IDENTIFIER | |||
| agnDlciTable | 1.3.6.1.4.1.164.3.1.2.8.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnDlciEntry | |||
| agnDlciEntry | 1.3.6.1.4.1.164.3.1.2.8.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnDlciEntry | |||
| agnDlciCnfgIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnDlciLSltIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. vs=Voice Switching In the ?004 Unit the entries io6(10)..io16) are not valid. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) LSlotIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx. | |||
| OBJECT-TYPE | |||
| INTEGER | cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), vs(254), notApplicable(255) | ||
| agnDlciLPrtIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.3 | ||
| This attribute indicates a unique external or internal port number, including linkSelector or encapsulator. 100=noConnect (for voice switching) LPrtIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnDlciLIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.4 | ||
| This attribute indicates a unique index for each possible used dlci(16..991). 0=notApplicable (for voice switching) LIdx is defined according one of the following possiblities: 1. LSlotIdx is < HSlotIdx. 2. LSlotIdx is = HSlotIdx and LPrtIdx is < HPrtIdx. 3. LSlotIdx is = HSlotIdx and LPrtIdx is = HPrtIdx but LIdx is < HIdx. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..991 | ||
| agnDlciHSltIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.5 | ||
| This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. For ISDN BRI ports of MX300/30 units: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| agnDlciHPrtIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.6 | ||
| This attribute indicates a unique port id which the dlci is routed to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnDlciHIdx | 1.3.6.1.4.1.164.3.1.2.8.1.1.7 | ||
| This attribute indicates a unique internal connection dlci number which the src dlci is routed to. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| agnDlciTxBc | 1.3.6.1.4.1.164.3.1.2.8.1.1.8 | ||
| This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBc5100bps(3), txBc6400bps(4), txBc8300bps(5), txBc9600bps(6), txBc14400bps(7), txBc19200bps(8), txBc28800bps(9), txBc32000bps(10), txBc38400bps(11), txBc48000bps(12), txBc56000bps(13), txBc57600bps(14), txBc64Kbps(15), txBc128Kbps(16), txBc192Kbps(17), txBc256Kbps(18), txBc320Kbps(19), txBc384Kbps(20), txBc448Kbps(21), txBc512Kbps(22), txBc768Kbps(23), txBc896Kbps(24), txBc1024Kbps(25), txBc1152Kbps(26), txBc1280Kbps(27), txBc1344Kbps(28), txBc1472Kbps(29), txBc1600Kbps(30), txBc1728Kbps(31), txBc1856Kbps(32), txBc1920Kbps(33), txBc1984Kbps(34), txBc2048Kbps(35), txBc16000bps(36), txBc112Kbps(37), txBc168Kbps(38), txBc224Kbps(39), txBc336Kbps(40), txBc672Kbps(41), txBc1536Kbps(42), txBc1792Kbps(43) | ||
| agnDlciTxBe | 1.3.6.1.4.1.164.3.1.2.8.1.1.9 | ||
| This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBe5100bps(3), txBe6400bps(4), txBe8300bps(5), txBe9600bps(6), txBe14400bps(7), txBe19200bps(8), txBe28800bps(9), txBe32000bps(10), txBe38400bps(11), txBe48000bps(12), txBe56000bps(13), txBe57600bps(14), txBe64Kbps(15), txBe128Kbps(16), txBe192Kbps(17), txBe256Kbps(18), txBe320Kbps(19), txBe384Kbps(20), txBe448Kbps(21), txBe512Kbps(22), txBe768Kbps(23), txBe896Kbps(24), txBe1024Kbps(25), txBe1152Kbps(26), txBe1280Kbps(27), txBe1344Kbps(28), txBe1472Kbps(29), txBe1600Kbps(30), txBe1728Kbps(31), txBe1856Kbps(32), txBe1920Kbps(33), txBe1984Kbps(34), txBe2048Kbps(35), txBe16000bps(36), txBe112Kbps(37), txBe168Kbps(38), txBe224Kbps(39), txBe336Kbps(40), txBe672Kbps(41), txBe1536Kbps(42), txBe1792Kbps(43) | ||
| agnDlciRxBc | 1.3.6.1.4.1.164.3.1.2.8.1.1.10 | ||
| This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBc5100bps(3), rxBc6400bps(4), rxBc8300bps(5), rxBc9600bps(6), rxBc14400bps(7), rxBc19200bps(8), rxBc28800bps(9), rxBc32000bps(10), rxBc38400bps(11), rxBc48000bps(12), rxBc56000bps(13), rxBc57600bps(14), rxBc64Kbps(15), rxBc128Kbps(16), rxBc192Kbps(17), rxBc256Kbps(18), rxBc320Kbps(19), rxBc384Kbps(20), rxBc448Kbps(21), rxBc512Kbps(22), rxBc768Kbps(23), rxBc896Kbps(24), rxBc1024Kbps(25), rxBc1152Kbps(26), rxBc1280Kbps(27), rxBc1344Kbps(28), rxBc1472Kbps(29), rxBc1600Kbps(30), rxBc1728Kbps(31), rxBc1856Kbps(32), rxBc1920Kbps(33), rxBc1984Kbps(34), rxBc2048Kbps(35), rxBc16000bps(36), rxBc112Kbps(37), rxBc168Kbps(38), rxBc224Kbps(39), rxBc336Kbps(40), rxBc672Kbps(41), rxBc1536Kbps(42), rxBc1792Kbps(43) | ||
| agnDlciRxBe | 1.3.6.1.4.1.164.3.1.2.8.1.1.11 | ||
| This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBe5100bps(3), rxBe6400bps(4), rxBe8300bps(5), rxBe9600bps(6), rxBe14400bps(7), rxBe19200bps(8), rxBe28800bps(9), rxBe32000bps(10), rxBe38400bps(11), rxBe48000bps(12), rxBe56000bps(13), rxBe57600bps(14), rxBe64Kbps(15), rxBe128Kbps(16), rxBe192Kbps(17), rxBe256Kbps(18), rxBe320Kbps(19), rxBe384Kbps(20), rxBe448Kbps(21), rxBe512Kbps(22), rxBe768Kbps(23), rxBe896Kbps(24), rxBe1024Kbps(25), rxBe1152Kbps(26), rxBe1280Kbps(27), rxBe1344Kbps(28), rxBe1472Kbps(29), rxBe1600Kbps(30), rxBe1728Kbps(31), rxBe1856Kbps(32), rxBe1920Kbps(33), rxBe1984Kbps(34), rxBe2048Kbps(35), rxBe16000bps(36), rxBe112Kbps(37), rxBe168Kbps(38), rxBe224Kbps(39), rxBe336Kbps(40), rxBe672Kbps(41), rxBe1536Kbps(42), rxBe1792Kbps(43) | ||
| agnDlciPriority | 1.3.6.1.4.1.164.3.1.2.8.1.1.12 | ||
| This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 7 is the highest priority. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| agnDlciStatus | 1.3.6.1.4.1.164.3.1.2.8.1.1.13 | ||
| This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected | |||
| OBJECT-TYPE | |||
| INTEGER | disconnected(1), connected(2) | ||
| agnDlciSpoofing | 1.3.6.1.4.1.164.3.1.2.8.1.1.14 | ||
| This object refers to sending of RIP messages: - yes : RIP messages will be sent ONLY if there is a change in the Net. - no : RIP messages will be always sent. This object is relevant only when one side of the DLCI is a CL-NMS interface. Default=no. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnDlciFunnelEnable | 1.3.6.1.4.1.164.3.1.2.8.1.1.15 | ||
| This object selects Funnel activation enable/disable: - disabled: Funnel operation disabled. The agnDlciTxBe and agnDlciTxBc values are not used for funneling. - enabled : Funnel operation enabled. The agnDlciTxBe and agnDlciTxBc values are used for funneling calculations. This object is relevant only for an encapsulating DLCI. In case of a Link Selector DLCI, the agnDlciTxBe and agnDlciTxBc values are used for bandwidth of Link Selector. Default=disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(2), enabled(3) | ||
| agnDlciRoutingProtocol | 1.3.6.1.4.1.164.3.1.2.8.1.1.16 | ||
| This object is relevant only when one side of the DLCI is a CL-NMS interface. It defines which Routing Protocol will be used for management via CL-NMS port. notApplicable will be used for all slots but CL. rip is a proprietary rip protocol. Default=rip. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), rip(2), rip2(3), none(4) | ||
| agnDlciRowStatus | 1.3.6.1.4.1.164.3.1.2.8.1.1.17 | ||
| This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnRowStatus.255.id2.id3.id4.id5.id6.id7 = active(1). For destroying a row, the NMS should set: agnRowStatus.255.id2.id3.id4.id5.id6.id7 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| agnVoiceSwitching | 1.3.6.1.4.1.164.3.1.2.9 | ||
| OBJECT IDENTIFIER | |||
| agnVoiceSwConfTable | 1.3.6.1.4.1.164.3.1.2.9.1 | ||
| MXcess Configuration for Voice Switching. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnVoiceSwConfEntry | |||
| agnVoiceSwConfEntry | 1.3.6.1.4.1.164.3.1.2.9.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnVoiceSwConfEntry | |||
| agnVoiceSwConfIdx | 1.3.6.1.4.1.164.3.1.2.9.1.1.1 | ||
| Active or Temporary Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnVoiceSwConfZoneId | 1.3.6.1.4.1.164.3.1.2.9.1.1.2 | ||
| 1 or 2 digits, (0-9)(1-9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..2) | ||
| agnVoiceSwConfNodeId | 1.3.6.1.4.1.164.3.1.2.9.1.1.3 | ||
| 1, 2 or 3 digits, (1-9),(0-9),(0-9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..3) | ||
| agnVoiceSwConfNoOfHops | 1.3.6.1.4.1.164.3.1.2.9.1.1.4 | ||
| Number of hops the frame will go through the net before deciding to discard the frame (like time-to-live in IP). 0 = notApplicable Default=20 . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..20 | ||
| agnVoiceSwConfSidt | 1.3.6.1.4.1.164.3.1.2.9.1.1.5 | ||
| SIDT: Short Inter Digit Timeout used as timer (in sec.) between digits after routing is completed. The timeout indicates end of dialing and the call can then be setup. 0 = notApplicable Default=2 sec. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..30 | ||
| agnVoiceSwConfLidt | 1.3.6.1.4.1.164.3.1.2.9.1.1.6 | ||
| LIDT: Long Inter Digit Timeout used as timer between digits before routing is completed. If no digits were dialed and LIDT expired then the user will get an error tone and the call will be disconnected. 0 = notApplicable Default=15 sec. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..30 | ||
| agnVoiceSwConfDialPlan | 1.3.6.1.4.1.164.3.1.2.9.1.1.7 | ||
| This is the Dialing Plan method that will be used in the Voice Switching. Static Dialing Plan - Routing is defined by the current device Zone and Node ID in the Network. Static Dialing Plan Plus - Includes the Static Dialing Plan but contains an addition of defining the number of dialed digits. Flexible Dialing Plan - Routing is defined in a flexible form. In this plan the user can configure the extension number of a local voice channel, Route a call to a remote destination and enter the Number of Digits for a specific dial prefix. | |||
| OBJECT-TYPE | |||
| INTEGER | staticDialPlan(2), staticDialPlanPlus(3), flexDialPlan(4) | ||
| agnVoiceSwConfRtTable | 1.3.6.1.4.1.164.3.1.2.9.2 | ||
| Routing Table for Voice Switching. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnVoiceSwConfRtEntry | |||
| agnVoiceSwConfRtEntry | 1.3.6.1.4.1.164.3.1.2.9.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnVoiceSwConfRtEntry | |||
| agnVoiceSwConfRtDbId | 1.3.6.1.4.1.164.3.1.2.9.2.1.1 | ||
| Active or Temporary Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnVoiceSwConfRtIdx | 1.3.6.1.4.1.164.3.1.2.9.2.1.2 | ||
| The Index of the row. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnVoiceSwConfRtDigits | 1.3.6.1.4.1.164.3.1.2.9.2.1.3 | ||
| Dialed digits: Series of digits 0...9, '*', '#' or '%'. The '*' and '#' can have many uses according to the user's decision. For example, they can be used as part of the Dialed Number, they exist on the phone number panel. '*' can also be used instead of a series of numbers. The '%' means any digits (wildcard) and is used without a series of digits. When the agnVoiceSwConfRtAction is del (7), the series of digits that are configured via this MIB object will be deleted from the prefix of the dialed number. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..7) | ||
| agnVoiceSwConfRtAction | 1.3.6.1.4.1.164.3.1.2.9.2.1.4 | ||
| Action that the system should perform for the digits: agnVoiceSwConfRtDigits. The action that is allowed depends on the Dialing Plan. Here is the list of the allowed actions: For Static Dialing Plan - zone, node, in, shortDialing, hgr, del, rep For Static Dialing Plan Plus - zone, node, in, shortDialing, hgr, del, rep, numDigDP For Flexible Dialing Plan - hgr, del, rep, numDigDP, route, ext | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), zone(2), node(3), shortDialing(4), in(5), hgr(6), del(7), rep(8), pri(9), bri(10), numDigDP(11), route(12), ext(13) | ||
| agnVoiceSwConfRtData | 1.3.6.1.4.1.164.3.1.2.9.2.1.5 | ||
| This field is relevant for actions hgr(6), and rep(8), numDigDP(11) and contains the following information: For hgr - the number of the Hunt Group. For rep - the number of digits to be replaced with. For numDigDP - the number of digits collected before establishing the call. 0 indicates no defined length. In this case SIDT will be used. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..7) | ||
| agnVoiceSwConfRtSlot | 1.3.6.1.4.1.164.3.1.2.9.2.1.6 | ||
| Routing Slot- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| agnVoiceSwConfRtPort | 1.3.6.1.4.1.164.3.1.2.9.2.1.7 | ||
| Routing Port- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). 100=noConnect (for non-routing case). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnVoiceSwConfRtDlci | 1.3.6.1.4.1.164.3.1.2.9.2.1.8 | ||
| Routing DLCI- Relevant for actions zone(2), node(3), shortDialing(4), route(12), ext(13). Valid values: 0=notApplicable (for non-routing case). 1, 16..991 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnVoiceSwConfRtRowStatus | 1.3.6.1.4.1.164.3.1.2.9.2.1.9 | ||
| Status of the row for creating/deleting entries in the table. The only possible supported RowStatus vaules are active (1), notInService (2), notReady(3), createAndGo(4), createAndWait(5) and destroy(6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| agnVoiceSwConfRtMaxCalls | 1.3.6.1.4.1.164.3.1.2.9.2.1.10 | ||
| Maximum no. of simultaneous voice calls that are allowed in the direction defined by the current entry. Default=0 (No Limit). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnVoiceSwConfHGTable | 1.3.6.1.4.1.164.3.1.2.9.5 | ||
| Table of Hunt Groups. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnVoiceSwConfHGEntry | |||
| agnVoiceSwConfHGEntry | 1.3.6.1.4.1.164.3.1.2.9.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnVoiceSwConfHGEntry | |||
| agnVoiceSwConfHGdbIdx | 1.3.6.1.4.1.164.3.1.2.9.5.1.1 | ||
| Active or Temporary Table. Both configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| agnVoiceSwConfHGIdx | 1.3.6.1.4.1.164.3.1.2.9.5.1.2 | ||
| There may be up to 10 Hunt Groups per MXcess. That's the index of the hunt group relevant to this row. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| agnVoiceSwConfHGConnect | 1.3.6.1.4.1.164.3.1.2.9.5.1.3 | ||
| This attribute indicates whether the hunt group should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| agnVoiceSwConfHGExt | 1.3.6.1.4.1.164.3.1.2.9.5.1.4 | ||
| This is the extension number of the hunt group. 0 is for not valid. The allowed range is 10 - 99. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| agnSigProfile | 1.3.6.1.4.1.164.3.1.2.10 | ||
| OBJECT IDENTIFIER | |||
| agnSigProfileTable | 1.3.6.1.4.1.164.3.1.2.10.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. The table includes signaling profile parameters for Legacy Profiles. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSigProfileEntry | |||
| agnSigProfileEntry | 1.3.6.1.4.1.164.3.1.2.10.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSigProfileEntry | |||
| agnSigProfileCnfgIdx | 1.3.6.1.4.1.164.3.1.2.10.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnSigProfileIdx | 1.3.6.1.4.1.164.3.1.2.10.1.1.2 | ||
| This attribute indicates the Signaling Profile (1..5). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..5 | ||
| agnSigProfileRxTx | 1.3.6.1.4.1.164.3.1.2.10.1.1.3 | ||
| This attribute indicates if the following objects refer to: Rx or Tx translation. Rx : ML->IO Tx : IO->ML . | |||
| OBJECT-TYPE | |||
| INTEGER | rx(1), tx(2) | ||
| agnSigProfileABCD | 1.3.6.1.4.1.164.3.1.2.10.1.1.4 | ||
| This object represents 6 parameters, by 3 Octets : Busy Code-MSB nibble, - applicable only for Rx translation Idle Code- nibble, - applicable only for Rx translation D Bit Code- nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of Busy and Idle Code nibble will have the valid values: 0000 .. FFFF. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-F hex - not used (invalid values) When the object is not applicable, the Octet String will have 0 bytes. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnSigProfTable | 1.3.6.1.4.1.164.3.1.2.10.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. This is the general table of signaling profiles. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnSigProfEntry | |||
| agnSigProfEntry | 1.3.6.1.4.1.164.3.1.2.10.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnSigProfEntry | |||
| agnSigProfCnfgIdx | 1.3.6.1.4.1.164.3.1.2.10.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnSigProfIdx | 1.3.6.1.4.1.164.3.1.2.10.2.1.2 | ||
| This attribute indicates the Signaling Profile (1..5). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..5 | ||
| agnSigProfName | 1.3.6.1.4.1.164.3.1.2.10.2.1.3 | ||
| Profile Name given by user. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..12) | ||
| agnSigProfType | 1.3.6.1.4.1.164.3.1.2.10.2.1.4 | ||
| Profile Type. legacy - usual signaling. The parameters for the Legacy Profiles are detailed in the agnSigProfileTable, above. r2Cas - R2 signaling. The parameters for the R2 Profiles are detailed in the r2 ProfileCnfg tables (belong to r2If). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), legacy(2), r2Cas(3) | ||
| agnSystemTs | 1.3.6.1.4.1.164.3.1.2.11 | ||
| OBJECT IDENTIFIER | |||
| agnTsTable | 1.3.6.1.4.1.164.3.1.2.11.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnTsEntry | |||
| agnTsEntry | 1.3.6.1.4.1.164.3.1.2.11.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnTsEntry | |||
| agnTsCnfgIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnTsSltIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| agnTsPrtIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.3 | ||
| This attribute indicates a unique external or internal port number. For MP, the valid values will be (for MLs only): - exPrt1(1)..exPrt4(4) - inPrt1(101)..inPrt4(104) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.4 | ||
| This attribute indicates a unique index for TS (Time-Slot). - for T1 ports - 1..24, Fbit(25) - for E1 ports - 1..31 - for HDSL ports - 1..32 ; 32 will represent TS0. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..32 | ||
| agnTsBitIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.5 | ||
| This attribute indicates a unique index for the Bit of each TS (Time-Slot). 1..8 - Bit 1.. Bit 8 255 - notApplicable This object is applicable only in Split Time-Slot cases. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsConSltIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.6 | ||
| This attribute indicates a unique slot position In the Mux where the TS is routed to. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| agnTsConPrtIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.7 | ||
| This attribute indicates a unique port id the TS is routed to. notApplicable - when agnTsType=mng or spare For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt48 (148). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTsConIdx | 1.3.6.1.4.1.164.3.1.2.11.1.1.8 | ||
| This attribute indicates a unique TS number the Src TS is routed to. Valid values: - for T1 ports - 1..24, Fbit(25) - for E1 ports - 1..31 - for HDSL ports - 1..32 ; 32 will represent TS0. - notApplicable - 255 (for ports that don't have TSs). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| agnTsType | 1.3.6.1.4.1.164.3.1.2.11.1.1.9 | ||
| Time-Slot Type - regarding its connection and media type. voice, data, vcMP - connected and the media is specified. mng - management. This TS is Dedicated to Management (not disconnected, but not connected to another port). spare - applicable for ML-20 only. These TSs should be reserved for future connection, though at the moment are not connected. reserved - these TSs are not connected, but they are Reserved for Protection (back-up) of a certain Path. Therefore, should NOT be used for connection of other Paths. dChannel - is used only when the TS is connected to a V5.1 ML (Bypass) and it contains ISDN D Channel data. In this case, agnTsConSltIdx, agnTsConPrtIdx and agnTsConIdx, will be 'notApplicable', since no TS is assigned for D Ch in V5.1 ML. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), voice(2), data(3), vcMP(4), mng(6), spare(7), reserved(8), dChannel(9) | ||
| agnTsRowStatus | 1.3.6.1.4.1.164.3.1.2.11.1.1.10 | ||
| This attribute allows to create/delete a row in this table. For creating a row, the NMS should set agnTsRowStatus.255.id2.id3.id4.id5.id6.id7.id8 = active(1). For destroying a row, the NMS should set: agnTsRowStatus.255.id2.id3.id4.id5.id6.id7.id8 = destroy(6). Only rows with status active(1) are relevant. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| agnTsDirection | 1.3.6.1.4.1.164.3.1.2.11.1.1.11 | ||
| Direction of the connection. This parameter is especially important when in MP a ML is connected to an IO port that has no TSs, so it doesn't appear in the TS Assignment for the first 5 indexes. notApplicable - for products that do not support this object or for certain TS Types (for example: mng, spare) rx - the ML only Receives from the IO Port (the ML will appear in the first 5 indexes). tx - the ML only Transmits to the IO Port (the ML will appear in the first 5 indexes). Nothing is received back. both - the ML Receives and Transmits to the IO Port (the ML will appear in the first 5 indexes). bcastSrc - the ML is a Broadcast-Bidirectional Source. It Transmits to one or several IO Ports (including the one that appears in the last 3 indexes) and sometimes receives. The Port that responds is dynamic (it can be another each time). The ML will appear in the first 5 indexes. bcastDst - the ML is a Broadcast-Bidirectional Destination. Therefore, it Receives and sometimes Transmits. The ML will appear in the first 5 indexes. internal - for connection of TSs internally, within the same card. Such an assignment has no effect on the external TS connections of the same TS. A TS can be connected with 'internal' direction to a port of the same card and at the same time, connected by another direction to ports (and TSs) of other cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), rx(2), tx(3), both(4), bcastSrc(5), bcastDst(6), internal(7) | ||
| systemVoice | 1.3.6.1.4.1.164.3.1.2.12 | ||
| OBJECT IDENTIFIER | |||
| systemVoiceTable | 1.3.6.1.4.1.164.3.1.2.12.1 | ||
| General Parameters for voice - system level. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SystemVoiceEntry | |||
| systemVoiceEntry | 1.3.6.1.4.1.164.3.1.2.12.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SystemVoiceEntry | |||
| systemVoiceConfIdx | 1.3.6.1.4.1.164.3.1.2.12.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed - Active or Temporary Configurations. Idx 255 relates to the temporary TmpCnfg. All configurations can be read but only the Temporary can be written to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| systemVoiceNationalTone | 1.3.6.1.4.1.164.3.1.2.12.1.1.2 | ||
| Tone Characteristics (Amplitude, Frequency, delays etc.). These characteristics are defined according to the country. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), usa(2), australia(3), brazil(4), canada(5), france(6), germany(7), israel(8), mexico(9), portugal(10), russia(11), spain(12), unitedKingdom(13), czech(14), china(15) | ||
| mdlWanGen | 1.3.6.1.4.1.164.3.1.3 | ||
| OBJECT IDENTIFIER | |||
| statMdlGen | 1.3.6.1.4.1.164.3.1.3.1 | ||
| OBJECT IDENTIFIER | |||
| mdlSInstTable | 1.3.6.1.4.1.164.3.1.3.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlSInstEntry | |||
| mdlSInstEntry | 1.3.6.1.4.1.164.3.1.3.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlSInstEntry | |||
| mdlSInstSltIdx | 1.3.6.1.4.1.164.3.1.3.1.1.1.1 | ||
| A unique number to identify a slot position in the mux. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlSInstCardType | 1.3.6.1.4.1.164.3.1.3.1.1.1.2 | ||
| This attribute indicates the type of card installed in the specific slot position. Only PS cards are possible in the PS slots. Only CL cards are possible in the CL slots. Only IO cards are possible in the IO slots. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), acm(9), ps60W(10), ps100W(11), cl1(20), clEth(21), cl2(22), cl2Eth(23), cl3(24), cl3Eth(25), mPh1(31), mPh3(32), mPh1T1DSU(33), mPh1T1CSU(34), mPh1E1DSU(35), mPh1E1LTU(36), mtmlFT1(37), mtmlFE1(38), mtmlH4E1(39), mtmlH4E12W(40), mtmlH4T1(41), mtmlH4T12W(42), mtHsh4E1(43), mtHsh4E12W(44), mtHsh4T1(45), mtHsh4T12W(46), mtmlH2E1(47), mtmlH2E12W(48), mtmlH2T1(49), mtmlH2T12W(50), hsh2E1(51), hsh2E12W(52), hsh2T1(53), hsh2T12W(54), mlIp(55), mtml4Ip(56), mPl6(60), mPl3(61), ml2E1(68), ml4E1(69), ml2T1(70), ml4T1(71), mPv4(72), vc16A(73), vc8EandM(74), vc8Fxo(75), vc8Fxs(76), vc16EandM(77), vc16Fxo(78), vc16Fxs(79), vf3EandM(80), vf3Fxs(81), vf3Fxo(82), vfPbx(83), vfPbxT1(84), vfPbxE1(85), mtMlE2S(86), mtMlE2D(87), mtMlF2T1(88), mtMlF2E1(89), mtMlT1Fiber(90), mtMlE1Fiber(91), mtMlT1FiberFb(92), mtMlE1FiberFb(93), mtmlHE1(94), mtmlH1E1(95), mtmlHSE1(96), ml20(97), mtMl4T1(98), mtMl4E1(99), mtMl1T1DSU(100), mtMl1T1CSU(101), mtMl1E1DSU(102), mtMl1E1LTU(103), mtMl1T1DSUfb(104), mtMl1T1CSUfb(105), mtMl1E1DSUfb(106), mtMl1E1LTUfb(107), mtMl2T1(108), mtMl2E1(109), ls2CcittX50(110), ls2CcittX58(111), ls2ATandTSdm(112), ls2ACcittX50(113), ls2ACcittX58(114), ls2AATandTSdm(115), ls2A2Ts(116), ls2M(117), mtMlT1(118), mtMlE1(119), hs2(120), hs3(121), hsq(122), hs703(123), hsQM(124), hsqN(125), hs6(126), hs12(127), hsDp(128), hsp(129), hs4T1(130), hs4E1(131), hs4(132), hsEth(133), vc2E1(136), vc4E1(137), vc2T1(138), vc4T1(139), vc2EandM(140), vc2Fxs1Plar(141), vc2Fxo1(142), vc2Fxs2(143), vc2Fxo2(144), vc2Fxs3(145), vc2Fxo3(146), vc26EandM(147), mtvc2(148), vc2R2Fxs(149), hsu(150), mbeA(151), mbeB(152), mbeU(153), tre(154), hsuI(155), hsr(156), hss(157), hsu1(158), ls12(159), ls6(160), ls6V1EandM(161), ls6V1Fxo(162), ls6V1Fxs(163), ls6V2EandM(164), ls6V2Fxo(165), ls6V2Fxs(166), ls6VfEandM(167), ls6VfFxo(168), ls6VfFxs(169), vc3EandM(170), vc3Fxo(171), vc3Fxs(172), vcPbx(173), vcPbxT1(174), vcPbxE1(175), vc6EandM(176), vc6Fxo(177), vc6Fxs(178), vcq(179), ls6n(180), mhs1V36(181), mhs1V35(182), mhs1G703(183), mhs1DDS(184), mhs3(185), mhs1X21(186), mhs1V24(187), mhs4(188), mhsE1Hs(189), mhsT1Hs(190), mhsHyE1Hs(191), mhsHyT1Hs(192), mlfHybE1Hs(193), mlfHybT1Hs(194), mhs2e1(195), mhs2t1(196), mhsHy2e1(197), mhsHy2t1(198), mlfHybE12(199), mls6(200), mls3(201), mlHybAtmE1(202), mlHybAtmT1(203), mlfHybT12(204), mvc8(205), mvc8PbxE1(206), mvc8PbxT1Dsu(207), mvc8PbxT1Csu(208), mvc8PbxE1Slave(209), mvc4(210), mvc4PbxE1(211), mvc4PbxT1Dsu(212), mvc4PbxT1Csu(213), mvc4PbxE1Slave(214), mvc4PbxT1Slave(215), mvc8PbxT1Slave(216), mvc8ExtAnalog(217), mvcE1(218), mvcT1(219), mhsS(220), mhsU(221), mhsPriE1(222), mhsPriT1(223), mPriE1FramerCcs(225), mPriT1FramerCcs(226), mPriE1SlaveCcs(227), mPriT1SlaveCcs(228), mDualBri(229), vc12EandM(230), vc12Fxo(231), vc12Fxs(232), vc6aEandM(233), vc6aFxo(234), vc6aFxs(235), vc6AgFxo(236), vc6AgFxs(237), vc6a4LB(238), hsu12(240), hsu6(241), hss12(242), hss6(243), mhsHyE1(247), mhsHyT1(248), mhsIp(249), mlIpHs(250), mlHybIpE1(251), mlHybIpT1(252), mvg1Lan(253), mvg2Lan(254) | ||
| mdlSHwVersion | 1.3.6.1.4.1.164.3.1.3.1.1.1.3 | ||
| This attribute indicates the Hardware version of the installed card in the specific slot position. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlSSwVersion | 1.3.6.1.4.1.164.3.1.3.1.1.1.4 | ||
| This attribute indicates the Software version of the installed card in the specific slot position. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlSAlrStatus | 1.3.6.1.4.1.164.3.1.3.1.1.1.5 | ||
| Indicates the alarm state at module level, i.e. lower level (port alarms) status is not included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlSAlrStatusAll | 1.3.6.1.4.1.164.3.1.3.1.1.1.6 | ||
| Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlSMaskedAlrStat | 1.3.6.1.4.1.164.3.1.3.1.1.1.7 | ||
| Indicates the alarm state at module level, [i.e. lower level (port alarms) status is not included],including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlSMaskedAlrStatAll | 1.3.6.1.4.1.164.3.1.3.1.1.1.8 | ||
| Indicates the alarm state in the module-all level, i.e. lower level (port alarms) included, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlSTstStatusAll | 1.3.6.1.4.1.164.3.1.3.1.1.1.9 | ||
| This attribute will be set to on(3) when there is at least one test in progress on a channel of the card, otherwise the value will be off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSClearAlrCmd | 1.3.6.1.4.1.164.3.1.3.1.1.1.10 | ||
| Setting this command to ON, enforces a clear of all the alarms in the given slot, excluding alarms of port level. The clear operation will not be applied for masked/inverted alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSClearAllAlrCmd | 1.3.6.1.4.1.164.3.1.3.1.1.1.11 | ||
| Setting this command to ON, enforces a clear of all the alarms in the given slot, including all its ports alarms. The clear operation will not be applied for masked/inverted alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSAlrTable | 1.3.6.1.4.1.164.3.1.3.1.2 | ||
| The list of card agent alarms ; includes also an alarm indicating existence of alarms on its ports if there are any. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlSAlrEntry | |||
| mdlSAlrEntry | 1.3.6.1.4.1.164.3.1.3.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlSAlrEntry | |||
| mdlSAlrIdx | 1.3.6.1.4.1.164.3.1.3.1.2.1.1 | ||
| A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlSAlrSltIdx | 1.3.6.1.4.1.164.3.1.3.1.2.1.2 | ||
| This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlSAlrCodeDescription | 1.3.6.1.4.1.164.3.1.3.1.2.1.3 | ||
| This attribute is a full text description of the alarm . The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlSAlrCode | 1.3.6.1.4.1.164.3.1.3.1.2.1.4 | ||
| A code identifying the alarm of an entry in the alarm status table at card level. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlSAlrSeverity | 1.3.6.1.4.1.164.3.1.3.1.2.1.5 | ||
| The severity of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlSAlrState | 1.3.6.1.4.1.164.3.1.3.1.2.1.6 | ||
| State of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSAlrCounter | 1.3.6.1.4.1.164.3.1.3.1.2.1.7 | ||
| A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlSAlrMask | 1.3.6.1.4.1.164.3.1.3.1.2.1.8 | ||
| Alarm mask : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSAlrInvert | 1.3.6.1.4.1.164.3.1.3.1.2.1.9 | ||
| Alarm invert : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| cnfgMdlGen | 1.3.6.1.4.1.164.3.1.3.2 | ||
| OBJECT IDENTIFIER | |||
| mdlCPrgTable | 1.3.6.1.4.1.164.3.1.3.2.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlCPrgEntry | |||
| mdlCPrgEntry | 1.3.6.1.4.1.164.3.1.3.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlCPrgEntry | |||
| mdlCCnfgIdx | 1.3.6.1.4.1.164.3.1.3.2.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..100) being referred. Value 255 specifies the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| mdlCSltIdx | 1.3.6.1.4.1.164.3.1.3.2.1.1.2 | ||
| This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlCPrgCardType | 1.3.6.1.4.1.164.3.1.3.2.1.1.3 | ||
| This attribute indicates the type of card assigned to the specific slot in the common configuration. This object is identical in all the configurations (1..100). Only the TmpCnf(255) may have different value. The write operation is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), acm(9), ps48x60W(10), ps48x100W(11), ps110x60W(12), ps110x100W(13), ps220x60W(14), ps220x100W(15), ps180W(16), cl1(20), clEth(21), cl2(22), cl2Eth(23), cl3(24), cl3Eth(25), mPh1(31), mPh3(32), mPh1T1DSU(33), mPh1T1CSU(34), mPh1E1DSU(35), mPh1E1LTU(36), mtmlFT1(37), mtmlFE1(38), mtmlH4E1(39), mtmlH4E12W(40), mtmlH4T1(41), mtmlH4T12W(42), mtHsh4E1(43), mtHsh4E12W(44), mtHsh4T1(45), mtHsh4T12W(46), mtmlH2E1(47), mtmlH2E12W(48), mtmlH2T1(49), mtmlH2T12W(50), hsh2E1(51), hsh2E12W(52), hsh2T1(53), hsh2T12W(54), mlIp(55), mtml4Ip(56), mPl6(60), ml2E1(68), ml4E1(69), ml2T1(70), ml4T1(71), vc16A(73), vc8EandM(74), vc8Fxo(75), vc8Fxs(76), vc16EandM(77), vc16Fxo(78), vc16Fxs(79), vf3EandM(80), vf3Fxs(81), vf3Fxo(82), vfPbx(83), vfPbxT1(84), vfPbxE1(85), mtMlE2S(86), mtMlE2D(87), mtMlF2T1(88), mtMlF2E1(89), mtMlT1Fiber(90), mtMlE1Fiber(91), mtMlT1FiberFb(92), mtMlE1FiberFb(93), mtmlHE1(94), mtmlH1E1(95), mtmlHSE1(96), ml20(97), mtMl4T1(98), mtMl4E1(99), mtMl1T1DSU(100), mtMl1T1CSU(101), mtMl1E1DSU(102), mtMl1E1LTU(103), mtMl1T1DSUfb(104), mtMl1T1CSUfb(105), mtMl1E1DSUfb(106), mtMl1E1LTUfb(107), mtMl2T1(108), mtMl2E1(109), ls2CcittX50(110), ls2CcittX58(111), ls2ATandTSdm(112), ls2ACcittX50(113), ls2ACcittX58(114), ls2AATandTSdm(115), ls2A2Ts(116), ls2M(117), mtMlT1(118), mtMlE1(119), hs2(120), hs3(121), hsq(122), hs703(123), hsQM(124), hsqN(125), hs6(126), hs12(127), hsDp(128), hsp(129), hs4T1(130), hs4E1(131), hsEth(133), vc2E1(136), vc4E1(137), vc2T1(138), vc4T1(139), vc2EandM(140), vc2Fxs1Plar(141), vc2Fxo1(142), vc2Fxs2(143), vc2Fxo2(144), vc2Fxs3(145), vc2Fxo3(146), vc26EandM(147), mtvc2(148), vc2R2Fxs(149), hsu(150), mbeA(151), mbeB(152), mbeU(153), tre(154), hsuI(155), hsr(156), hss(157), hsu1(158), ls12(159), ls6(160), ls6V1EandM(161), ls6V1Fxo(162), ls6V1Fxs(163), ls6V2EandM(164), ls6V2Fxo(165), ls6V2Fxs(166), ls6VfEandM(167), ls6VfFxo(168), ls6VfFxs(169), vc3EandM(170), vc3Fxo(171), vc3Fxs(172), vcPbx(173), vcPbxT1(174), vcPbxE1(175), vc6EandM(176), vc6Fxo(177), vc6Fxs(178), vcq(179), ls6n(180), mhs1V36(181), mhs1V35(182), mhs1G703(183), mhs1DDS(184), mhs3(185), mhs1X21(186), mhs1V24(187), mhs4(188), mhsE1Hs(189), mhsT1Hs(190), mhsHyE1Hs(191), mhsHyT1Hs(192), mlfHybE1Hs(193), mlfHybT1Hs(194), mhs2e1(195), mhs2t1(196), mhsHy2e1(197), mhsHy2t1(198), mlfHybE12(199), mls6(200), mls3(201), mlHybAtmE1(202), mlHybAtmT1(203), mlfHybT12(204), mvc8(205), mvc8PbxE1(206), mvc8PbxT1Dsu(207), mvc8PbxT1Csu(208), mvc8PbxE1Slave(209), mvc4(210), mvc4PbxE1(211), mvc4PbxT1Dsu(212), mvc4PbxT1Csu(213), mvc4PbxE1Slave(214), mvc4PbxT1Slave(215), mvc8PbxT1Slave(216), mvc8ExtAnalog(217), mvcE1(218), mvcT1(219), mhsS(220), mhsU(221), mhsPriE1(222), mhsPriT1(223), mPriE1FramerCcs(225), mPriT1FramerCcs(226), mpriE1SlaveCcs(227), mpriT1SlaveCcs(228), mDualBri(229), vc12EandM(230), vc12Fxo(231), vc12Fxs(232), vc6aEandM(233), vc6aFxo(234), vc6aFxs(235), vc6AgFxo(236), vc6AgFxs(237), vc6a4LB(238), hsu12(240), hsu6(241), hss12(242), hss6(243), mhsHyE1(247), mhsHyT1(248), mhsIp(249), mlIpHs(250), mlHybIpE1(251), mlHybIpT1(252), mvg1Lan(253), mvg2Lan(254) | ||
| mdlCNoOfExternPrt | 1.3.6.1.4.1.164.3.1.3.2.1.1.4 | ||
| Number of external ports in the programmed card of the specific slot position | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCNoOfInternPrt | 1.3.6.1.4.1.164.3.1.3.2.1.1.5 | ||
| Number of internal ports in the programmed card of the specific slot position. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCWorkMode | 1.3.6.1.4.1.164.3.1.3.2.1.1.6 | ||
| Working mode of the card. The user may configure the card to work in a stand alone mode or integrated with the device. Example for use in MHS-IP cards: - standAlone - in this mode, the router works so that data is received via the LAN (Eth) port and is transmitted via the WAN (HS) external port without going through the MPH device. - integrated - in this mode, the router works so that it is integrated in the MPH and routes DLCIs into the device. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), standAlone(2), integrated(3) | ||
| cmprMdlGen | 1.3.6.1.4.1.164.3.1.3.3 | ||
| OBJECT IDENTIFIER | |||
| mdlCmprTable | 1.3.6.1.4.1.164.3.1.3.3.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlCmprEntry | |||
| mdlCmprEntry | 1.3.6.1.4.1.164.3.1.3.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlCmprEntry | |||
| mdlCmprTypIdx | 1.3.6.1.4.1.164.3.1.3.3.1.1.1 | ||
| This attribute indicates the Type of the Compressed being referred. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.3.3.1.1.2 | ||
| This attribute indicates the configuration to which the Compressed information is related. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCmprVersion | 1.3.6.1.4.1.164.3.1.3.3.1.1.3 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCmprSltIdx | 1.3.6.1.4.1.164.3.1.3.3.1.1.4 | ||
| This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlCmprObj | 1.3.6.1.4.1.164.3.1.3.3.1.1.5 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlAlarmsCmprTable | 1.3.6.1.4.1.164.3.1.3.3.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlAlarmsCmprEntry | |||
| mdlAlarmsCmprEntry | 1.3.6.1.4.1.164.3.1.3.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlAlarmsCmprEntry | |||
| mdlAlarmsCmprVersion | 1.3.6.1.4.1.164.3.1.3.3.2.1.1 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlarmsCmprAlarmSlot | 1.3.6.1.4.1.164.3.1.3.3.2.1.2 | ||
| This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlarmsCmprAlarmIdx | 1.3.6.1.4.1.164.3.1.3.3.2.1.3 | ||
| A unique number to identify an entry in the alarm status table of the agent. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlarmsCmprObj | 1.3.6.1.4.1.164.3.1.3.3.2.1.4 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtWanGen | 1.3.6.1.4.1.164.3.1.4 | ||
| OBJECT IDENTIFIER | |||
| statPrtGen | 1.3.6.1.4.1.164.3.1.4.1 | ||
| OBJECT IDENTIFIER | |||
| prtSInstTable | 1.3.6.1.4.1.164.3.1.4.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSInstEntry | |||
| prtSInstEntry | 1.3.6.1.4.1.164.3.1.4.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtSInstEntry | |||
| prtSInstSltIdx | 1.3.6.1.4.1.164.3.1.4.1.1.1.1 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted. In the ?004 Unit the entries io6(10)..io(16) are not valid. For the Vmux2100 Main Board clA (3) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtSInstPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.1.1.2 | ||
| This attribute indicates a unique number to identify a port in a specific card. The valid ports depend on the installed card: the valid external ports (interfaces) are (1..mdlCNoOfExternPrt) if any, and the valid internal ports are (101..100+mdlCNoOfInternPrt) if any. Generally: exPrt1 (1) .. exPrt16 (16),inPrt1 (101) .. inPrt48 (148) For the Vmux-2100 device: This index will have values of 1...4 for the physical ports & values of ifIndex for the bundles. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSInstPrtType | 1.3.6.1.4.1.164.3.1.4.1.1.1.3 | ||
| This attribute describes the type of the designated port. In MX 3000 only external & internal options are used. All the other options are only for MX 30/300 which need special handling. In order to support interface types in MX 3000, return an ascii string for prtSInterfaceType in this table or support the general RAD value of physicalConnector. External port - is a port with a physical connector. Internal port - might be of two types: a) A composite port which collects a few external ports data into a common bandwidth (usually routed through DS1 link) b) A port which gets only part of the external ports (usually a few DS0's) The following types are used when all ports are external/ internal and the connector/interface type is necessary (for example, stand-alone units): High Speed port types Low Speed port types Voice port types, CL port types. ISDN Voice in MX 30/300 Phase 4: voiceS0 (16), voiceU (17) should be used. ISDN Voice in MX 30/300 Phase 5: voiceQsigS(18), voiceQsigU (19) should be used. | |||
| OBJECT-TYPE | |||
| INTEGER | external(2), internal(3), highSpeedV35(4), highSpeedV24(5), highSpeedV36(6), highSpeedX21(7), highSpeedG703(8), highSpeedDDS(9), lowSpeed(10), voice(11), cl(12), isdns(13), isdnu(14), ethernet(15), voiceS0(16), voiceU(17), voiceQsigS(18), voiceQsigU(19) | ||
| prtSInstIfIndex | 1.3.6.1.4.1.164.3.1.4.1.1.1.4 | ||
| This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx the value will be '7fffffff'h. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSActiveStatus | 1.3.6.1.4.1.164.3.1.4.1.1.1.5 | ||
| This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the ch is not connected according to the active config. offLine(3) indicates that the ch is down (not working) because of any problem. onLine(4) indicates that the ch is up (working) offLineRedundancy(5) indicates that the ch is down, because it is redundant port. onLineRedundancy(6) indicates that the ch is up, and it is the active link | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), notUsed(2), offLine(3), onLine(4), offLineRedundancy(5), onLineRedundancy(6) | ||
| prtSAlrStatus | 1.3.6.1.4.1.164.3.1.4.1.1.1.6 | ||
| Indicates the alarm state in the port(ch) agent level. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| prtSMaskedAlrStat | 1.3.6.1.4.1.164.3.1.4.1.1.1.7 | ||
| Indicates the alarm state in the port(ch) agent level, including Masked alarms. This attribute will be set to: critical(7) - when there is at least one active (state ON) critical alarm, otherwise it will be set to major(5) - when there is at least one active (state ON) major alarm, otherwise it will be set to minor(4) - if there is at least one active (state ON) minor alarm, otherwise it will be set to warning(6) - if there is at least one active (state ON) warning alarm, otherwise it will be set to event(3) - if there was at least one alarm event (including state on,off events) since the last clear operation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| prtSClearAlrCmd | 1.3.6.1.4.1.164.3.1.4.1.1.1.8 | ||
| Setting this attribute to on(3) enforces a clear operation of the alarm status events in the given port. The clear operation will not be applied for masked/inverted alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSTestMask | 1.3.6.1.4.1.164.3.1.4.1.1.1.9 | ||
| This is a mask which indicates which tests from the 'prtSTstCmd' list are allowed for the requested port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- local-loop 1 remote-loop 2 loc-and-rem-main-loops 3 remote-analog-loop 4 remote-digital-loop 5 rem-loop-on-ext-unit 6 bert 7 tone-injection 8 dlci local-loop 9 all dlci local-loop 10 dlci remote-loop 11 all dlci remote-loop 12 bert-and-rem-loop-on-rem-unit 13 rem-loop-on-rem-unit 14 block 15 backward-tone-inject 16 llb 17 rlb 18 ft1Enable 21 lbbd 22 --for 2B+D lb1 23 --for B1 lb2 24 --for B2 llb-on-rem-unit 25 bert-on-rem-unit 26 bert-on-rem-and-llb-on-rem-unit 27 local-and-bert-on-rem-unit 28 local-loop-on-rem-unit 29 localBert 30 --towards IO ports test-per-TS 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSTstCmd | 1.3.6.1.4.1.164.3.1.4.1.1.1.10 | ||
| Setting this attribute to any of the above values will initiate a test on the specific port if the operation is legal. If the operation is not legal, the mux will ignore the operation. testPerTS(31) - when this test is selected, the selection of tests for each TS is done via the prtExPh1MlTsTest object. If a test time out is needed, the test will be set with a default timeout of 2 minutes until the user will set the parameter 'prtSTstDuration' to the required time out. If no time out is needed , the test will be set with infinite timeout until the user will set the parameter 'prtSTstDuration' to the required time out. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), localLoop(2), remoteLoop(3), locAndRemMainLoops(4), remoteAnalogLoop(5), remoteDigitalLoop(6), remLoopOnExtUnit(7), bert(8), toneInjection(9), dlciLocalLoop(10), allDlciLocalLoop(11), dlciRemoteLoop(12), allDlciRemoteLoop(13), extInitLocalLoop(14), bertAndRemLoopOnRemUnit(15), remLoopOnRemUnit(16), block(17), backwardToneInject(18), llb(19), rlb(20), ft1Enable(21), lbbd(22), lb1(23), lb2(24), llbOnRemUnit(25), bertOnRemUnit(26), bertOnRemAndLlbOnRemUnit(27), localAndBertOnRemUnit(28), localLoopOnRemUnit(29), localBert(30), testPerTS(31) | ||
| prtSTstDuration | 1.3.6.1.4.1.164.3.1.4.1.1.1.11 | ||
| This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to all the test operations. The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtSTstCmd' parameter. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSBertClrCmd | 1.3.6.1.4.1.164.3.1.4.1.1.1.12 | ||
| Setting this attribute initiates bert count clear operation. It is valid only when bert test is active on the specific port. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSBertTstRslt | 1.3.6.1.4.1.164.3.1.4.1.1.1.13 | ||
| This attribute indicates the number of Bit Error Rate indicated during the BERT operation. It is valid only when bert test is active on the specific port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSInterfaceType | 1.3.6.1.4.1.164.3.1.4.1.1.1.14 | ||
| This attribute indicates a unique HW interface type of the selected port. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtSParamStatus | 1.3.6.1.4.1.164.3.1.4.1.1.1.15 | ||
| This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For VC-6, VC-6A, VC-6AG, VC-6A/4LB, VC-12, VC-12/6, external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 |_| |_________| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 |___| |_______| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |___________| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For ACM external port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |_________| spare Alarm State Alarm State: according to bits 1,0: 00=NA ; 01=unused ; 10=Off ; 11=On - For HS-U/1 external port - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For MTML-2 external ports, MTML-E2 internal ports - 1 Octet : Bit 7 6 5 4 3 2 1 0 LSB | BERT State BERT State (Bit 0): 0 = OFF (BERT is not running on this port or any of its TSs/Bits) 1 = ON (BERT is running on this port OR on one of its TSs/Bits) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtSAlrTable | 1.3.6.1.4.1.164.3.1.4.1.2 | ||
| The list of port agent alarms. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSAlrEntry | |||
| prtSAlrEntry | 1.3.6.1.4.1.164.3.1.4.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtSAlrEntry | |||
| prtSAlrIdx | 1.3.6.1.4.1.164.3.1.4.1.2.1.1 | ||
| A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlrSltIdx | 1.3.6.1.4.1.164.3.1.4.1.2.1.2 | ||
| This attribute indicates a unique identifier of the slot where the card is inserted. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io12(16) are not valid. For the Vmux2100 Main Board clA (3) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtSAlrPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.2.1.3 | ||
| This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a port which does not exist. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148), IP Bundles. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlrCodeDescription | 1.3.6.1.4.1.164.3.1.4.1.2.1.4 | ||
| This attribute is a full text description of the alarm. The alarm description includes the following information: alarm code, alarm text, alarm severity, Masked or Inverted flag and counter. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtSAlrCode | 1.3.6.1.4.1.164.3.1.4.1.2.1.5 | ||
| A code identifying the alarm of an entry in the alarm status table at port level. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlrSeverity | 1.3.6.1.4.1.164.3.1.4.1.2.1.6 | ||
| The severity of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| prtSAlrState | 1.3.6.1.4.1.164.3.1.4.1.2.1.7 | ||
| State of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSAlrCounter | 1.3.6.1.4.1.164.3.1.4.1.2.1.8 | ||
| A counter - how many times the alarm occured since last clear operation. ON and OFF Alarm will be counted separately. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlrMask | 1.3.6.1.4.1.164.3.1.4.1.2.1.9 | ||
| Alarm mask : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSAlrInvert | 1.3.6.1.4.1.164.3.1.4.1.2.1.10 | ||
| Alarm invert : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| statisPrtGen | 1.3.6.1.4.1.164.3.1.4.1.3 | ||
| OBJECT IDENTIFIER | |||
| prtFrStatis | 1.3.6.1.4.1.164.3.1.4.1.3.1 | ||
| OBJECT IDENTIFIER | |||
| prtFrStatisTable | 1.3.6.1.4.1.164.3.1.4.1.3.1.1 | ||
| This table is applicable only for an active port running an FR protocol . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtFrStatisEntry | |||
| prtFrStatisEntry | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtFrStatisEntry | |||
| prtFrStatisSltIdx | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.1 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255). | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtFrStatisPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.2 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtFrStatisInvIdx | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.3 | ||
| The Interval of 15 min. for which the following statistics counters are applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | currentInv(1), last(2) | ||
| prtFrTimeElapsed | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.4 | ||
| The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..899 | ||
| prtFrRxTotalFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.5 | ||
| The total number of frames received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxTotalFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.6 | ||
| The total number of frames sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxTotalBytes | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.7 | ||
| The total number of bytes received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxTotalBytes | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.8 | ||
| The total number of bytes sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxMngFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.9 | ||
| The management number of frames received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxMngFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.10 | ||
| The management number of frames sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxDeFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.11 | ||
| The number of De frames received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxDeFrames | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.12 | ||
| The number of De frames sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxDcrdCongDeFr | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.13 | ||
| The number of De frames discarded due to congestion, received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxDcrdCongDeFr | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.14 | ||
| The number of De frames discarded due to congestion, sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxDcrdCongAllFr | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.15 | ||
| All the frames discarded due to congestion, received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxDcrdCongAllFr | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.16 | ||
| All the frames discarded due to congestion, sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxFecn | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.17 | ||
| Number of frames received by this port during the selected interval, indicating forward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxFecn | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.18 | ||
| Number of frames sent by this port during the selected interval, indicating forward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxBecn | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.19 | ||
| Number of frames received by this port during the selected interval, indicating backward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxBecn | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.20 | ||
| Number of frames sent by this port during the selected interval, indicating backward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxBeViol | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.21 | ||
| Number of data frames received by this port during the selected interval, exceeding the Burst Excess value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxBeViol | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.22 | ||
| Number of data frames sent by this port during the selected interval, exceeding the Burst Excess value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrRxBcViol | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.23 | ||
| Number of data frames received by this port during the selected interval, exceeding the Burst Committed value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtFrTxBcViol | 1.3.6.1.4.1.164.3.1.4.1.3.1.1.1.24 | ||
| Number of data frames sent by this port during the selected interval, exceeding the Burst Committed value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtCrStatis | 1.3.6.1.4.1.164.3.1.4.1.3.2 | ||
| OBJECT IDENTIFIER | |||
| prtCrStatisTable | 1.3.6.1.4.1.164.3.1.4.1.3.2.1 | ||
| This table is applicable only for an active port running a CR protocol . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtCrStatisEntry | |||
| prtCrStatisEntry | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtCrStatisEntry | |||
| prtCrStatisSltIdx | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.1 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255). | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtCrStatisPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.2 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtCrStatisInvIdx | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.3 | ||
| The Interval of 15 min. for which the following statistics counters are applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | currentInv(1), last(2) | ||
| prtCrTimeElapsed | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.4 | ||
| The number of seconds that have elapsed since the beginning of the current error-measurement interval. This object is applicable mainly for the current interval. For other interval: - if data is available: value will be 899. - if data is not available: value will be 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..899 | ||
| prtCrRxTotalCells | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.5 | ||
| The total number of cells received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtCrTxTotalCells | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.6 | ||
| The total number of cells sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtCrRxDataCells | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.7 | ||
| The number of Data Cells received by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtCrTxDataCells | 1.3.6.1.4.1.164.3.1.4.1.3.2.1.1.8 | ||
| The number of Data Cells sent by this port during the selected interval. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciStatis | 1.3.6.1.4.1.164.3.1.4.1.3.3 | ||
| OBJECT IDENTIFIER | |||
| prtDlciStatisTable | 1.3.6.1.4.1.164.3.1.4.1.3.3.1 | ||
| This table is applicable only for an active port running an FR, FR+ or CR protocol, with valid DLCIs . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtDlciStatisEntry | |||
| prtDlciStatisEntry | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtDlciStatisEntry | |||
| prtDlciSltIdx | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.1 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For stand-alone units this index will be notApplicable (255). | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtDlciPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.2 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtDlciIdx | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.3 | ||
| This attribute indicates a unique DLCI index for each valid DLCI (16..991). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtDlciRxDeFrames | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.4 | ||
| The number of De frames received by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxDeFrames | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.5 | ||
| The number of De frames sent by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciRxDcrdCongDeFr | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.6 | ||
| The number of De frames discarded due to congestion, received by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxDcrdCongDeFr | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.7 | ||
| The number of De frames discarded due to congestion, sent by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciRxDcrdCongAllFr | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.8 | ||
| All the frames discarded due to congestion, received by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxDcrdCongAllFr | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.9 | ||
| All the frames discarded due to congestion, sent by this DLCI. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxFecn | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.10 | ||
| Number of frames sent by this DLCI, indicating forward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxBecn | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.11 | ||
| Number of frames sent by this DLCI, indicating backward congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciRxBeViol | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.12 | ||
| Number of data frames received by this DLCI, exceeding the Burst Excess value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxBeViol | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.13 | ||
| Number of data frames sent by this DLCI, exceeding the Burst Excess value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciRxBcViol | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.14 | ||
| Number of data frames received by this DLCI, exceeding the Burst Committed value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtDlciTxBcViol | 1.3.6.1.4.1.164.3.1.4.1.3.3.1.1.15 | ||
| Number of data frames sent by this DLCI, exceeding the Burst Committed value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| prtT1Statis | 1.3.6.1.4.1.164.3.1.4.1.3.4 | ||
| OBJECT IDENTIFIER | |||
| prtT1FdlMsgTable | 1.3.6.1.4.1.164.3.1.4.1.3.4.1 | ||
| This table is applicable for a T1 interface with 'esf' LineType . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtT1FdlMsgEntry | |||
| prtT1FdlMsgEntry | 1.3.6.1.4.1.164.3.1.4.1.3.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtT1FdlMsgEntry | |||
| prtT1FdlMsgSltIdx | 1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.1 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtT1FdlMsgPrtIdx | 1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.2 | ||
| This attribute indicates a unique port number. MTML-1/T1 modules have just one external interface. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtT1FdlMsgFdlTxRx | 1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.3 | ||
| The Fdl tx/rx reference of the Fdl message. | |||
| OBJECT-TYPE | |||
| INTEGER | tx(1), rx(2) | ||
| prtT1FdlMsg | 1.3.6.1.4.1.164.3.1.4.1.3.4.1.1.4 | ||
| FDL message. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| cnfgPrtGen | 1.3.6.1.4.1.164.3.1.4.2 | ||
| OBJECT IDENTIFIER | |||
| prtExTsSplitTable | 1.3.6.1.4.1.164.3.1.4.2.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExTsBitTest that will be written directly to the Active Configuration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExTsSplitEntry | |||
| prtExTsSplitEntry | 1.3.6.1.4.1.164.3.1.4.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExTsSplitEntry | |||
| prtExTsCnfgIdx | 1.3.6.1.4.1.164.3.1.4.2.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExTsSltIdx | 1.3.6.1.4.1.164.3.1.4.2.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExTsPrtIdx | 1.3.6.1.4.1.164.3.1.4.2.1.1.3 | ||
| This attribute indicates a unique port number. Most ML cards have only one external interface. inPrt1 - for MTML-H/E1 cards. For other products' index see their specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExTsIdx | 1.3.6.1.4.1.164.3.1.4.2.1.1.4 | ||
| This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExTsBit | 1.3.6.1.4.1.164.3.1.4.2.1.1.5 | ||
| This attribute indicates a unique Bit within the time slot. The valid Bits are: 1..8. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| prtExTsIConSlot | 1.3.6.1.4.1.164.3.1.4.2.1.1.6 | ||
| This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - for stand-alone units. | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExTsIConPrt | 1.3.6.1.4.1.164.3.1.4.2.1.1.7 | ||
| This attribute indicates the internally (In Mux) connected/routed port. For other products' index see their specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExTsBitTest | 1.3.6.1.4.1.164.3.1.4.2.1.1.8 | ||
| This attribute indicates a test to be activated on the selected Bit. It is applicable only when prtExPh1MlTsTest=split(254). none - no test is applied for the selected Bit. notApplicable - when prtExPh1MlTsTest is NOT split(254). | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), remoteBert(8), localBert(30), notApplicable(255) | ||
| prtExTsTxSignaling | 1.3.6.1.4.1.164.3.1.4.2.1.1.9 | ||
| Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It defines what is sent for the selected TS for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtExTsRxSignaling | 1.3.6.1.4.1.164.3.1.4.2.1.1.10 | ||
| Tx Signaling per TS, for TSs having TS Type=Voice (agnTsType=voice(2)). It defines what is sent for the selected TS for A,B,C,D Signaling Bits. Bit 1= LSB Bit 8= MSB Bit 1-2 = A Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 3-4 = B Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 5-6 = C Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA Bit 7-8 = D Signaling Bit: 00='0' ; 01='1' ; 10=not used ; 11=NA | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtCnfgAgenda | 1.3.6.1.4.1.164.3.1.4.2.2 | ||
| OBJECT IDENTIFIER | |||
| prtAgendaBehaviourTable | 1.3.6.1.4.1.164.3.1.4.2.2.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtAgendaBehaviourEntry | |||
| prtAgendaBehaviourEntry | 1.3.6.1.4.1.164.3.1.4.2.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtAgendaBehaviourEntry | |||
| prtAgendaBehaviourCnfgIdx | 1.3.6.1.4.1.164.3.1.4.2.2.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtAgendaBehaviourSltIdx | 1.3.6.1.4.1.164.3.1.4.2.2.1.1.2 | ||
| This parameter should be: - slot number for MX3000 - 255 = N/A for MX300/30. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAgendaBehaviourPrtIdx | 1.3.6.1.4.1.164.3.1.4.2.2.1.1.3 | ||
| This parameter should be: - port number for MX300/30 - 100 = N/A for MX3000. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAgendaBehaviourOnOff | 1.3.6.1.4.1.164.3.1.4.2.2.1.1.4 | ||
| Setting this command to on(3) enables the agenda function at module (3000) or port (300/30) level. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtCnfgAgendaTable | 1.3.6.1.4.1.164.3.1.4.2.2.2 | ||
| This table allows the user to schedule the time a session is active per week basis. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtCnfgAgendaEntry | |||
| prtCnfgAgendaEntry | 1.3.6.1.4.1.164.3.1.4.2.2.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtCnfgAgendaEntry | |||
| prtCnfgAgendaCnfgIdx | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtCnfgAgendaSltIdx | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.2 | ||
| This attribute is equal to: -slot number for MX3000 -255 = N/A for MX300/30 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCnfgAgendaPrtIdx | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.3 | ||
| This attribute is equal to: - port number for MX300/30 - port number for MX3000. For example 1-4 in MHS-4 cards. - 100 = N/A for MX3000 when not used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCnfgAgendaDayIdx | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.4 | ||
| This attribute for which day of the week this row applies. | |||
| OBJECT-TYPE | |||
| INTEGER | monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6), sunday(7) | ||
| prtCnfgAgendaSesId | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.5 | ||
| The user may define 4 different active intervals per day. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| prtCnfgAgendaFrom | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.6 | ||
| Start from time interval in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..86400 | ||
| prtCnfgAgendaTo | 1.3.6.1.4.1.164.3.1.4.2.2.2.1.7 | ||
| To time interval in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..86400 | ||
| prtGenCnfgTable | 1.3.6.1.4.1.164.3.1.4.2.3 | ||
| This table allows the user to configure general port parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtGenCnfgEntry | |||
| prtGenCnfgEntry | 1.3.6.1.4.1.164.3.1.4.2.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtGenCnfgEntry | |||
| prtGenCnfgIdx | 1.3.6.1.4.1.164.3.1.4.2.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtGenCnfgSltIdx | 1.3.6.1.4.1.164.3.1.4.2.3.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtGenCnfgPrtIdx | 1.3.6.1.4.1.164.3.1.4.2.3.1.3 | ||
| This attribute indicates a unique external or internal port number. For MP: exPrt1 (1) .. exPrt16 (16) , notApplicable(100), inPrt1 (101) .. inPrt48 (148) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenCnfgLinkToSlot | 1.3.6.1.4.1.164.3.1.4.2.3.1.4 | ||
| This attribute indicates the slot of the ML card to which the IO port is mapped. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtGenCnfgLinkToPort | 1.3.6.1.4.1.164.3.1.4.2.3.1.5 | ||
| This attribute indicates the port in the prtGenCnfgLinkToSlot of the ML card to which the IO port is mapped. For MP: exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , notApplicable (255) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenCnfgPortId | 1.3.6.1.4.1.164.3.1.4.2.3.1.6 | ||
| IO Port Id for V5.1 use. This object is applicable only for part of the PSTN and ISDN IO ports. Generally, 0 is a valid value. Nevertheless, for ports that do not support this object, the value will be: notApplicable= 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..16777215 | ||
| cmprPrtGen | 1.3.6.1.4.1.164.3.1.4.3 | ||
| OBJECT IDENTIFIER | |||
| prtCmprTable | 1.3.6.1.4.1.164.3.1.4.3.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtCmprEntry | |||
| prtCmprEntry | 1.3.6.1.4.1.164.3.1.4.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtCmprEntry | |||
| prtCmprTypIdx | 1.3.6.1.4.1.164.3.1.4.3.1.1.1 | ||
| This attribute indicates the Type of the Compressed being referred. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.4.3.1.1.2 | ||
| This attribute indicates the configuration to which the Compressed information is related. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCmprVersion | 1.3.6.1.4.1.164.3.1.4.3.1.1.3 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCmprSltIdx | 1.3.6.1.4.1.164.3.1.4.3.1.1.4 | ||
| This attribute indicates a unique number of the slot position where the card is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtCmprPrtIdx | 1.3.6.1.4.1.164.3.1.4.3.1.1.5 | ||
| This attribute indicates a unique identifier of the port the compressed information relates to. Valid values: exPrt1 (1) .. exPrt16 (16) , inPrt1 (101) .. inPrt48 (148). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCmprObj | 1.3.6.1.4.1.164.3.1.4.3.1.1.6 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtCmprStatisticObj | 1.3.6.1.4.1.164.3.1.4.3.1.1.7 | ||
| This attribute is the compressed statistics information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtDlciCmprTable | 1.3.6.1.4.1.164.3.1.4.3.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtDlciCmprEntry | |||
| prtDlciCmprEntry | 1.3.6.1.4.1.164.3.1.4.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtDlciCmprEntry | |||
| prtDlciCmprCnfgIdx | 1.3.6.1.4.1.164.3.1.4.3.2.1.1 | ||
| This attribute indicates the configuration to which the Compressed information is related. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDlciCmprVersion | 1.3.6.1.4.1.164.3.1.4.3.2.1.2 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDlciCmprSltIdx | 1.3.6.1.4.1.164.3.1.4.3.2.1.3 | ||
| This attribute indicates a unique number of the slot position where the module is inserted. In the ?004 Unit the entries psB(2),clB(4),io6(10)..io(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtDlciCmprPrtIdx | 1.3.6.1.4.1.164.3.1.4.3.2.1.4 | ||
| This attribute indicates a unique identifier of the port the compressed information relates to. All the values are valid. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112) | ||
| prtDlciCmprDlciIdx | 1.3.6.1.4.1.164.3.1.4.3.2.1.5 | ||
| This attribute indicates a unique identifier of the Dlci the compressed information relates to. The values are between 16 - 991. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDlciCmprObj | 1.3.6.1.4.1.164.3.1.4.3.2.1.6 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtAlarmsCmprTable | 1.3.6.1.4.1.164.3.1.4.3.3 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtAlarmsCmprEntry | |||
| prtAlarmsCmprEntry | 1.3.6.1.4.1.164.3.1.4.3.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtAlarmsCmprEntry | |||
| prtAlarmsCmprVersion | 1.3.6.1.4.1.164.3.1.4.3.3.1.1 | ||
| This attribute indicates the version of the internal format of the Compressed data | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlarmsCmprAlarmSlot | 1.3.6.1.4.1.164.3.1.4.3.3.1.2 | ||
| This attribute indicates the desired slot position. In the ?004 Unit the entries PsB(2),ClB(4),io6(10)..io(16) are not valid. For Stand-alone units, notApplicable(255) will appear. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlarmsCmprAlarmPort | 1.3.6.1.4.1.164.3.1.4.3.3.1.3 | ||
| This attribute indicates a unique identifier of the port the alarm applies to. All the values are valid. No alarms exist for a non-existing port. IP Bundles are considered a port too, for this matter. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlarmsCmprAlarmIdx | 1.3.6.1.4.1.164.3.1.4.3.3.1.4 | ||
| A unique number to identify an entry in the alarm status table of the agent. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlarmsCmprObj | 1.3.6.1.4.1.164.3.1.4.3.3.1.5 | ||
| This attribute is the compressed information itself. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mapWanGen | 1.3.6.1.4.1.164.3.1.5 | ||
| OBJECT IDENTIFIER | |||
| agnLinkMapTable | 1.3.6.1.4.1.164.3.1.5.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AgnLinkMapEntry | |||
| agnLinkMapEntry | 1.3.6.1.4.1.164.3.1.5.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AgnLinkMapEntry | |||
| mapLinkId | 1.3.6.1.4.1.164.3.1.5.1.1.1 | ||
| A unique identifier of the link | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mapLinkSltIdx | 1.3.6.1.4.1.164.3.1.5.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries clA(3), io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), clA(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| mapLinkPrtIdx | 1.3.6.1.4.1.164.3.1.5.1.1.3 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112) | ||
| mapLinkStatus | 1.3.6.1.4.1.164.3.1.5.1.1.4 | ||
| This attribute indicates the status of the link between the two muxes | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), down(2), up(3) | ||
| diverseIfWanGen | 1.3.6.1.4.1.164.3.1.6 | ||
| OBJECT IDENTIFIER | |||
| ethIf | 1.3.6.1.4.1.164.3.1.6.1 | ||
| OBJECT IDENTIFIER | |||
| ethIfTable | 1.3.6.1.4.1.164.3.1.6.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EthIfEntry | |||
| ethIfEntry | 1.3.6.1.4.1.164.3.1.6.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| EthIfEntry | |||
| ethIfIdx | 1.3.6.1.4.1.164.3.1.6.1.1.1.1 | ||
| A unique index of the ethernet interface/port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ethMode | 1.3.6.1.4.1.164.3.1.6.1.1.1.2 | ||
| This object indicates the Ethernet mode of operation. | |||
| OBJECT-TYPE | |||
| INTEGER | halfDuplex(1), fullDuplex(2), notApplicable(255) | ||
| ethBridgingMode | 1.3.6.1.4.1.164.3.1.6.1.1.1.3 | ||
| This object indicates the bridging mode of the Ethernet interface. | |||
| OBJECT-TYPE | |||
| INTEGER | filtered(1), transparent(2) | ||
| ethEncapsulationCRCMode | 1.3.6.1.4.1.164.3.1.6.1.1.1.4 | ||
| This object define the encapsulation type requested for the Ethernet interface. It indicates if we transfer the Ethernet frame to the other side with or without the CRC. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), withCRC(2), withoutCRC(3) | ||
| ethBackPressure | 1.3.6.1.4.1.164.3.1.6.1.1.1.5 | ||
| This parameter defines whether to enable or disable Back pressure. Back Pressure is a flow control parameter. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| ethLimit4 | 1.3.6.1.4.1.164.3.1.6.1.1.1.6 | ||
| This parameter determine the Back off algorithm mode. Every 4 following collisions the Framer will be thrown out (4 times more than usuall). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| ethSkipInitReset | 1.3.6.1.4.1.164.3.1.6.1.1.1.7 | ||
| This parameter defines whether read status on reset. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), notSkip(2), skip(3) | ||
| ethMulticastBlock | 1.3.6.1.4.1.164.3.1.6.1.1.1.8 | ||
| This parameter defines whether to send multicast message to WAN from LAN or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unBlock(2), block(3) | ||
| ethBroadcastBlock | 1.3.6.1.4.1.164.3.1.6.1.1.1.9 | ||
| This parameter defines whether to send broadcast message to WAN from LAN or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unBlock(2), block(3) | ||
| ethSpeed | 1.3.6.1.4.1.164.3.1.6.1.1.1.10 | ||
| This parameter defines the line speed. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), s10Mbps(2), s100Mbps(3) | ||
| ethIfPerformance | 1.3.6.1.4.1.164.3.1.6.1.2 | ||
| OBJECT IDENTIFIER | |||
| ethIfCurrentTable | 1.3.6.1.4.1.164.3.1.6.1.2.1 | ||
| The Ethernet Current table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EthIfCurrentEntry | |||
| ethIfCurrentEntry | 1.3.6.1.4.1.164.3.1.6.1.2.1.1 | ||
| An entry in the Ethernet Current table. | |||
| OBJECT-TYPE | |||
| EthIfCurrentEntry | |||
| ethIfCurrentIndex | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.1 | ||
| The index of the Ethernet interface. It may be ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ethIfCurrentStatus | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.2 | ||
| The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| ethIfCurrentInFrames | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.3 | ||
| The counter associated with the number of received frames, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentInOctets | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.4 | ||
| The counter associated with the number of received octets, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentAlignmentErrors | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.5 | ||
| The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentFCSErrors | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.6 | ||
| The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentLengthError | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.7 | ||
| The counter associated with the number of received frames with length error, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentOutFrames | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.8 | ||
| The counter associated with the number of transmitted frames, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentOutOctets | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.9 | ||
| The counter associated with the number of transmitted octets, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentSingleCollisionFrames | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.10 | ||
| The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentMultipleCollisionFrames | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.11 | ||
| The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentDeferredTransmissions | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.12 | ||
| The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentLateCollisions | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.13 | ||
| The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfCurrentCarrierSenseErrors | 1.3.6.1.4.1.164.3.1.6.1.2.1.1.14 | ||
| The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalTable | 1.3.6.1.4.1.164.3.1.6.1.2.2 | ||
| The Ethernet Interval table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EthIfIntervalEntry | |||
| ethIfIntervalEntry | 1.3.6.1.4.1.164.3.1.6.1.2.2.1 | ||
| An entry in the Ethernet Interval table. | |||
| OBJECT-TYPE | |||
| EthIfIntervalEntry | |||
| ethIfIntervalIndex | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.1 | ||
| The index of the Ethernet interface. It may be ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| ethIfIntervalNumber | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.2 | ||
| A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..96 | ||
| ethIfIntervalStatus | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.3 | ||
| The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| ethIfIntervalInFrames | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.4 | ||
| The counter associated with the number of received frames, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalInOctets | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.5 | ||
| The counter associated with the number of received octets, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalAlignmentErrors | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.6 | ||
| The counter associated with the number of received frames, which are not complete (The result of dividing the number of bits by 8 is not an Integer), encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalFCSErrors | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.7 | ||
| The counter associated with the number of received frames that didn't pass the FCS test, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalLengthError | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.8 | ||
| The counter associated with the number of received frames with length error, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalOutFrames | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.9 | ||
| The counter associated with the number of transmitted frames, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalOutOctets | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.10 | ||
| The counter associated with the number of transmitted octets, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalSingleCollisionFrames | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.11 | ||
| The counter associated with the number of successfully transmitted frames for which transmission was inhibited by exactly one collision, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalMultipleCollisionFrames | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.12 | ||
| The counter associated with the number of successfully transmitted frames for which transmission was inhibited by more than one collision, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalDeferredTransmissions | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.13 | ||
| The counter associated with the number of transmitted frames for which the first transmission attempt was delayed due to a busy media, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalLateCollisions | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.14 | ||
| The counter associated with the number of times that a collision was detected later than the first 64 bytes of the frame, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| ethIfIntervalCarrierSenseErrors | 1.3.6.1.4.1.164.3.1.6.1.2.2.1.15 | ||
| The counter associated with the number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame, encountered by the Ethernet interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| muxHub | 1.3.6.1.4.1.164.3.2 | ||
| OBJECT IDENTIFIER | |||
| muxHubEvents | 1.3.6.1.4.1.164.3.2.0 | ||
| The events for . | |||
| OBJECT-IDENTITY | |||
| alarmsTrap | 1.3.6.1.4.1.164.3.2.0.1 | ||
| This trap is sent whenever alarm occurs in the agent. | |||
| NOTIFICATION-TYPE | |||
| alrBufDescription | |||
| sanityTrap | 1.3.6.1.4.1.164.3.2.0.2 | ||
| This trap is sent after a data base update. It returns the sanity result status and the configuration no. checked. If the result is of Flip DB Sanity Check, the configuration no. sent will be 0. If the result is of Variant Sanity Check, the configuration no. sent will be 100. | |||
| NOTIFICATION-TYPE | |||
| agnSSanityCheckStatus | |||
| agnCSaveCnfgIdxCmd | |||
| cnfgFlipTrap | 1.3.6.1.4.1.164.3.2.0.3 | ||
| This trap is sent upon change of the active Configuration DB. Attached, is the new active Configuration no. | |||
| NOTIFICATION-TYPE | |||
| agnSActiveCnfg | |||
| flipDbChangeTrap | 1.3.6.1.4.1.164.3.2.0.4 | ||
| This trap is sent upon change of the active Flip tables (Flip DB). | |||
| NOTIFICATION-TYPE | |||
| statusChangedTrap | 1.3.6.1.4.1.164.3.2.0.5 | ||
| This trap is sent upon any change of the LEDs status. | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| agnMux | 1.3.6.1.4.1.164.3.2.1 | ||
| OBJECT IDENTIFIER | |||
| mdlMux | 1.3.6.1.4.1.164.3.2.2 | ||
| OBJECT IDENTIFIER | |||
| cnfgMdlMux | 1.3.6.1.4.1.164.3.2.2.1 | ||
| OBJECT IDENTIFIER | |||
| mdlPbxFramerCnfg | 1.3.6.1.4.1.164.3.2.2.1.1 | ||
| OBJECT IDENTIFIER | |||
| mdlPbxFramerCnfgTable | 1.3.6.1.4.1.164.3.2.2.1.1.1 | ||
| This table contains parameters relevant to a module belonging to a digital voice system, except mdlPbxFraEnhEcho which is relevant also for analog cards. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlPbxFramerCnfgEntry | |||
| mdlPbxFramerCnfgEntry | 1.3.6.1.4.1.164.3.2.2.1.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlPbxFramerCnfgEntry | |||
| mdlPbxFraCnfgIdx | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlPbxFraSltIdx | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.2 | ||
| The slot relevant to this module. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlPbxFraEnhEcho | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.3 | ||
| Refers to external ports of an analogue module and to the internal ports of the other mvc4 types of modules. ms16(3) means that the four voice ports have enhanced echo of 16ms. ms32(4) means that the two first ports have enhanced echo of 32 ms while the last two ports have no enhanced echo. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), ms16(3), ms32(4) | ||
| mdlPbxFraTSGroupAss | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.4 | ||
| In case of T1 modules: group1=(1,2,3,4), ...., group6=(21,22,23,24) while in case of E1 modules: - If prtExPh1MlLineType=g732sE1 or g732sE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,17), group5=(18,19,20,21),...,group7=(26,27,28,29) group8=(30,31). - If prtExPh1MlLineType=g732nE1 or g732nE1CRC: group1=(1,2,3,4),..,group4=(13,14,15,16), group5=(17,18,19,20),...,group7=(25,26,27,28) group8=(29,30,31). | |||
| OBJECT-TYPE | |||
| INTEGER | group1(1), group2(2), group3(3), group4(4), group5(5), group6(6), group7(7), group8(8), notApplicable(255) | ||
| mdlPbxFraSignalMode | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.5 | ||
| Refers to the signaling mode of the Framer module. tieTrunk(2), tieInvert(3), casTrans(4) are standard coding of the signaling protocol. casTrans(4) is Channel Associated Signaling (the signaling is within the channels time slot). ccsTrans(6) is Transparent Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). userDefined(5) allows the user to define the signaling protocol he wants. In this case, the next two MIB fields are relevant. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), tieTrunk(2), tieInvert(3), casTrans(4), userDefined(5), ccsTrans(6), noSignaling(7) | ||
| mdlPbxFraSignalVector | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.6 | ||
| In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote In conjunction with the Mask, mdlPbxFraSignalMask, it is possible to compute the signal mode. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlPbxFraSignalMask | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.7 | ||
| In the case of mdlPbxFraSignalMode = userDefined(5), this field defines the 'don't care' A,B,C Bits. D bit is supplied for future versions. Bit 1 = Bit A ON Hook - Local Bit 2 = Bit B ON Hook - Local Bit 3 = Bit C ON Hook - Local Bit 4 = Bit D ON Hook - Local Bit 5 = Bit A OFF Hook - Local Bit 6 = Bit B OFF Hook - Local Bit 7 = Bit C OFF Hook - Local Bit 8 = Bit D OFF Hook - Local Bit 9 = Bit A ON Hook - Remote Bit 10 = Bit B ON Hook - Remote Bit 11 = Bit C ON Hook - Remote Bit 12 = Bit D ON Hook - Remote Bit 13 = Bit A OFF Hook - Remote Bit 14 = Bit B OFF Hook - Remote Bit 15 = Bit C OFF Hook - Remote Bit 16 = Bit D OFF Hook - Remote. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlPbxFraFramerSlot | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.8 | ||
| Slot where is sitting the Framer. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| mdlPbxFraSignaling | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.9 | ||
| Signaling - describes the way the signaling ABCD bits pass from the local extension to the remote extension and vice-versa. endToEnd = the signaling ABCD bits pass without change from local to remote extension. localTermination = the signaling ABCD bits received from the local extension are translated to different ON Hook/OFF Hook bit values and then passed to remote extension. This is relevant when the Local and Remote ON Hook/OFF Hook values are different. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), endToEnd(2), localTermination(3) | ||
| mdlPbxFraTransSigTs | 1.3.6.1.4.1.164.3.2.2.1.1.1.1.10 | ||
| This is the Time Slot that is used for Transparent CCS signaling. The values of this TS are 1-24 for T1 & 1-31 for E1. The default for E1 is 16 & for T1 it is 24. If no signaling is used then the TS should be 255 (None). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMux | 1.3.6.1.4.1.164.3.2.3 | ||
| OBJECT IDENTIFIER | |||
| statPrtMux | 1.3.6.1.4.1.164.3.2.3.1 | ||
| OBJECT IDENTIFIER | |||
| prtSExHsfStatTable | 1.3.6.1.4.1.164.3.2.3.1.6 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSExHsfStatEntry | |||
| prtSExHsfStatEntry | 1.3.6.1.4.1.164.3.2.3.1.6.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtSExHsfStatEntry | |||
| prtSExHsfSltIdx | 1.3.6.1.4.1.164.3.2.3.1.6.1.1 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtSExHsfPrtIdx | 1.3.6.1.4.1.164.3.2.3.1.6.1.2 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12) | ||
| prtSExHsfInterfaceTyp | 1.3.6.1.4.1.164.3.2.3.1.6.1.3 | ||
| This attribute indicates a unique interface type of a selected port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), v35(2), rs422(3) | ||
| prtSExHsfRts | 1.3.6.1.4.1.164.3.2.3.1.6.1.4 | ||
| This attribute indicates a unique RTS control signal state. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), notActive(2), active(3) | ||
| cnfgPrtMux | 1.3.6.1.4.1.164.3.2.3.2 | ||
| OBJECT IDENTIFIER | |||
| prtClCnfg | 1.3.6.1.4.1.164.3.2.3.2.1 | ||
| OBJECT IDENTIFIER | |||
| prtExClCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExClCnfgEntry | |||
| prtExClCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.1.1.1 | ||
| All the entries at this table are identical (have the same value) for all the configurations (1..100) except the TmpCnfg. The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| PrtExClCnfgEntry | |||
| prtExClCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExClSltIdx | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. Because the second Cl is only for redundancy, all the parameters are identical in the two modules, i.e. change of any parameter in one module will change automatically the value of the other module.. In the ?004 Unit the entry clB(4) is not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4), notApplicable(255) | ||
| prtExClPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.3 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2) | ||
| prtExClUsage | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.4 | ||
| This attribute indicates what is the usage of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), noUse(2), nmsSlip(3), nmsPpp(4), muxSlip(5), muxPpp(6), terminal(7) | ||
| prtExClRate | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.5 | ||
| This attribute indicates the operation rate of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | r300Bps(1), r1200Bps(2), r2400Bps(3), r4800Bps(4), r9600Bps(5), r19200Bps(6), r38400Bps(7), r57600Bps(8), r115200Bps(9) | ||
| prtExClDataBits | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.6 | ||
| This attribute indicates the number of data bits in async frame | |||
| OBJECT-TYPE | |||
| INTEGER | dataBits7Bits(1), dataBits8Bits(2) | ||
| prtExClParity | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.7 | ||
| This attribute indicates if the parity operation mode in async frame | |||
| OBJECT-TYPE | |||
| INTEGER | odd(1), even(2), none(3) | ||
| prtExClStopBits | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.8 | ||
| This attribute indicates the minimum number of stop bits in the tx async frame | |||
| OBJECT-TYPE | |||
| INTEGER | stopBits1Bit(1), stopBits1dot5Bits(2), stopBits2Bits(3) | ||
| prtExClRoutingProtocol | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.9 | ||
| This attribute indicates the routing protocol of the port. When prtExClUsage is nmsSlip or nmsPpp - all values are applicable . Else - only 'none' is applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), rip2(2) | ||
| prtExClEnabled | 1.3.6.1.4.1.164.3.2.3.2.1.1.1.10 | ||
| This attribute indicates if Ethernet port of CL is enabled or not for management. It is applicable only on the ETH port of the CL, when the MP includes an ML-IP card. disabled - will happen when there is Inband Management via the ML-IP link/s enabled - will happen when ML-IP link/s is not used for Inband Management, but CL's ETH port . | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtPh1MlCnfg | 1.3.6.1.4.1.164.3.2.3.2.2 | ||
| OBJECT IDENTIFIER | |||
| prtExPh1MlCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.2.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPh1MlCnfgEntry | |||
| prtExPh1MlCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPh1MlCnfgEntry | |||
| prtExPh1MlCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPh1MlSltIdx | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (1) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExPh1MlPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.3 | ||
| This attribute indicates a unique port number. MTML-1/E1 and MTML-1/T1 cards have only one external interface. inPrt1, inPrt2 - for MTML-H/2E1 and HSH cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards and others. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104) | ||
| prtExPh1MlConnect | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the card considerations because it may indicate that the module has only one physical interface. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPh1MlLineType | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.5 | ||
| This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for the MPH.1/T1 E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) | |||
| OBJECT-TYPE | |||
| INTEGER | esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7) | ||
| prtExPh1MlLineCode | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.6 | ||
| This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for MPH.1/T1 E1 line code parameters for MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6) | |||
| OBJECT-TYPE | |||
| INTEGER | b7T1(1), b8zsT1(2), transT1(3), hdb3E1(4), notApplicable(255) | ||
| prtExPh1MlLineLen | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.7 | ||
| This attribute is the line length parameter used only for T1/DSU interfaces. lenXXXpXXXft = len-XXX-XXXft. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), lenFcc68(7), notApplicable(255) | ||
| prtExPh1MlRestoreTime | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.8 | ||
| The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4) | ||
| prtExPh1MlTxGain | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.9 | ||
| This attribute is the tx gain parameter used only for T1/CSU interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), txGain0db(2), txGain7dot5db(3), txGain15db(4), txGain22dot5db(5) | ||
| prtExPh1MlRxSensitivity | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.10 | ||
| This attribute is the rx line sensitivity parameter. low26dBm, high36dBm - applicable for T1-CSU shortHaul, longHaul - applicable for MTML-4 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), low26dBm(2), high36dBm(3), shortHaul(4), longHaul(5) | ||
| prtExPh1MlIdleCode | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.11 | ||
| Determines the code for transmission in empty time slots. Type value(00-FFH), Excluding 0H,8H,10H,12H,21H,24H,42H,49H, 84H,92H | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPh1MlTdmTrunk | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.12 | ||
| This attribute indicates whether the port is used to transfer TDM cards data and through which Bus. | |||
| OBJECT-TYPE | |||
| INTEGER | linkA(1), linkB(2), none(3), notApplicable(255) | ||
| prtExPh1MlClkMode | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.13 | ||
| Defines the clock operation mode of the T1/E1 interface. Ports that are connected to the TDM Buses must be in nodalTiming(3) clock mode. | |||
| OBJECT-TYPE | |||
| INTEGER | internalLocal(1), loopBackLocal(2), nodalTiming(3) | ||
| prtExPh1MlMfClkSrcSlt | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.14 | ||
| This attribute indicates whether the port Tx multiframe is synchronized with Rx multiframe of another port and the slot position of that port. This operation is required in order to bypass signaling of PCM voice channels. Its value is always local(2) when the port isn't connected to any TDM bus. When it's value is local(2) there is no meaning to 'prtExPh1MlMfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExPh1MlMfClkSrcPrt | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.15 | ||
| A unique number to identify a port position in the mux. It has no effect when the prtExPh1MlMfClkSrcSlt selected is Local. inPrt1 - for MTML-H/E1 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), inPrt1(101), notApplicable(255) | ||
| prtExPh1MlFdlType | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.16 | ||
| A unique number to identify the side of the FDL operation. Normal: 'response' for the user side and 'command' for the PTT side. Applicable only when working with ESF-T1 link | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), response(2), command(3) | ||
| prtExPh1MlInbandMng | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.17 | ||
| A unique number to identify an Inband management over the link. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), fdlOrTs0(3), dedicatedTs(4), dedicatedPpp(5), dedicatedFr(6), notApplicable(255) | ||
| prtExPh1MlInbandMngRate | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.18 | ||
| A unique number to identify the rate of the Inband management. E1 port - it is not applicable when prtExPh1MlInbandMng selected is off. T1 port - it is not applicable when prtExPh1MlInbandMng selected is off OR fdlOrTs0. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r4k(2), r8k(3), r12k(4), r16k(5), r32k(6), r64k(7), r20k(8) | ||
| prtExPh1MlRedundType | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.19 | ||
| This object determines the ML redundancy type: none - no ML redundacy dualCableAIS - each ML card is connected by a separate dualCableParallelTx cable to the other MUX (two cables connect two MUXes). There are two types of dual redundancy. yCable - Y cable is connected to both ML cards (one cable connects two MUXes). Default=none When only one ML card exists, the type can be only 'none'. The value should be the same for both ML slots. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), dualCableAIS(2), yCable(3), dualCableParallelTx(4) | ||
| prtExPh1MlRedundSlot | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.20 | ||
| This object indicates the slot containing the redundacy ML card, coupled with the current ML (prtExPh1MlSltIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. In the ?004 Unit the entries io6(10)..io12(16) are not valid When value is not 'none', it should be mutual to the redundant ML slot. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExPh1MlRedundPort | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.21 | ||
| This object indicates the redundacy ML port, coupled with the current ML port (prtExPh1MlPrtIdx). When prtExPh1MlRedundType=none (no ML redundancy) this object will be 'notApplicable'. When value is not 'none', it should be mutual to the redundant ML port. inPrt1 - for MTML-H/E1 cards. inPrt1..inPrt4 - for MTML-E2 cards. exPrt2..exPrt4 - for MTML-4 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), notApplicable(255) | ||
| prtExPh1MlRedundRecTime | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.22 | ||
| Redundancy Recovery Time (sec). After switching the ML card to the current (prtExPh1MlSltIdx), the next ML switch can be performed only after a minimum time, indicated by this object. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| prtExPh1MlInbandMngRoutProt | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.23 | ||
| This attribute indicates the Inband Mng routing protocol of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), rip2(2), proprietary(3) | ||
| prtExPh1MlIfType | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.24 | ||
| Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), csu(2), dsu(3), ltu(4) | ||
| prtExPh1MlMultiplier | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.25 | ||
| The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), br56(2), br64(3) | ||
| prtExPh1MlSupportedTS | 1.3.6.1.4.1.164.3.2.3.2.2.1.1.26 | ||
| Number of Supported Time Slots by the agent. For Vmux-110 there is HW that supports less than 31/24 Time Slots for the E1/T1 port. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| prtExPh1MlTsTable | 1.3.6.1.4.1.164.3.2.3.2.2.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry, except prtExPh1MlTsTest that will be written directly to the Active Configuration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPh1MlTsEntry | |||
| prtExPh1MlTsEntry | 1.3.6.1.4.1.164.3.2.3.2.2.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPh1MlTsEntry | |||
| prtExPh1MlTsCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPh1MlTsSltIdx | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. For the Vmux2100 Main Board notApplicable (255) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPh1MlTsPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.3 | ||
| This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have only one external interface. exPrt2 - for ME1-2, MT1-2 and mhsPri cards. exPrt3, exPrt4 - for mhsPri cards. inPrt1 - for MTML-H/E1 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101) | ||
| prtExPh1MlTsIdx | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.4 | ||
| This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPh1MlTsIConSlot | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.5 | ||
| This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS). | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), noConnect(2), split(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPh1MlTsIConPrt | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.6 | ||
| This attribute indicates the internally (In Mux) connected/routed port. For MP, the values will be: { exPrt1 (1) , exPrt2 (2) , exPrt3 (3) , exPrt4 (4) , exPrt5 (5) , exPrt6 (6) , exPrt7 (7) , exPrt8 (8) , exPrt9 (9) , exPrt10 (10) , exPrt11 (11) , exPrt12 (12) , noConnect (100), inPrt1 (101) , inPrt2 (102) , inPrt3 (103) , inPrt4 (104) , inPrt5 (105) , inPrt6 (106) , inPrt7 (107) , inPrt8 (108) , inPrt9 (109) , inPrt10 (110) , inPrt11 (111) , inPrt12 (112) } | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPh1MlTsIConTs | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.7 | ||
| This attribute indicates a unique time slot position. The valid time slots are 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated to multiframe synchronization and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPh1MlTsExt | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.8 | ||
| A pointer to an extension of this table: prtExTsSplitTable. - If prtExPh1MlTsIConSlot='split', its value should be set to the OBJECT IDENTIFIER of the prtExTsSplitTable, with its relevant CnfgIdx, SltIdx, PrtIdx, TsIdx and 1st TsBit. - If prtExPh1MlTsIConSlot is not 'split', its value should be set to the OBJECT IDENTIFIER { 0 0 }. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| prtExPh1MlTsTest | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.9 | ||
| This attribute indicates a test to be activated on the selected TS. It is applicable only when prtSTstCmd=testPerTS(31). notApplicable - when prtSTstCmd is NOT testPerTS(31). none - no test is applied for the selected TS. split - when the tests are per Bit of the selected TS. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), localLoop(2), remoteLoop(3), remoteBert(8), localToneInjection(9), remoteToneInjection(18), localBert(30), split(254), notApplicable(255) | ||
| prtExPh1MlTsType | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.10 | ||
| The Time Slot Type. | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), data(3), voice(4), cas(5), notApplicable(255) | ||
| prtExPh1MlTsBundle | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.11 | ||
| The number of the bundle containing this Time Slot. If no bundle exists for this TS or the bundle number is irrelevant, the value will be 0. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| prtExPh1MlTsTestDuration | 1.3.6.1.4.1.164.3.2.3.2.2.2.1.12 | ||
| This attribute indicates the maximum duration of executing a test on the specific TS. This entry applies to all the test operations. For the Vmux2100 the values are: 0 - 60 seconds. A zero value specifies no time limitation. When the test isn't active, the agent initiates this object to 2 when the duration is needed and to 0 if its not required. The user should set this parameter after setting the 'prtExPh1MlTsTest' parameter. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtInPh1MlCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.2.3 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInPh1MlCnfgEntry | |||
| prtInPh1MlCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.2.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInPh1MlCnfgEntry | |||
| prtInPh1MlCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInPh1MlSltType | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. For ISDN BRI port of MX300/30: io1(5) = isdn1(5) and io2(6) = isdn2(6) In the ?004 Unit the entries io6(10)..io12(16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtInPh1MlPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.3 | ||
| This attribute indicates a unique port number. MPH.1/E1 and MPH.1/T1 cards have three internal interfaces. MX3000 modules may have up to 50 internal ports. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtInPh1MlConnect | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInPh1MlRate | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), noRate(100) | ||
| prtInPh1MlProtocol | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.6 | ||
| This attribute indicates the applied protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | fr(1), frPlus(2), pCellRelay(3), hdlcSdlc(4), transparentHdlc(5) | ||
| prtInPh1MlConnectionTyp | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.7 | ||
| This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management operation (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetNotMana - indicates network internal line, but the remote mux is not managed by the nms. User - User to Network Interface. OtherNet - Network To Network Interfce. PubNet - Access Mux To PubNet Interface. | |||
| OBJECT-TYPE | |||
| INTEGER | sameNetManaged(1), sameNetNotMana(2), user(3), otherNet(4), pubNet(5), notApplicable(255) | ||
| prtInPh1MlCongResponse | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.8 | ||
| This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/receive becn to/from the network). no - do nothing FlowControl - translate the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done in both directions. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), flowControl(3) | ||
| prtInPh1MlCongLevel | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.9 | ||
| This attribute indicates the level of delayed data in precents of the total available dynamic memory, for which the port will start to operate . The resolution of the parameter is 5 percent. Valid values: 10..70, 255. 255=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtInPh1MlTc | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.10 | ||
| This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports in the specific card. 255=notApplicable. | |||
| OBJECT-TYPE | |||
| INTEGER | tc1sec(1), tc2sec(2), tc3sec(3), tc4sec(4), notApplicable(255) | ||
| prtInPh1MlFlowControl | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.11 | ||
| This attribute indicates the required flow control betweeen the port and the remote equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | none(2), fecnBecn(3) | ||
| prtInPh1MlSegment | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.12 | ||
| This object is the Segmentation in Bytes. In protocol FR+, ISDN internals, MX 30/300 the segmentation is: 50 (2) ,158 (3) ,266 (4) ,376 (5), 484 (6) In MX 3000/4: For protocol FR+ (internal ISDN ports of MHS.S, MHS.U, MHS.E1, MHS.T1 cards) segmentation values are: 236 (7),472 (8), 708 (9), 944 (10) ,1180 (11) | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), s36Byte(2), s150Byte(3), s264Byte(4), s378Byte(5), s492Byte(6), s236Byte(7), s472Byte(8), s708Byte(9), s944Byte(10), s1180Byte(11) | ||
| prtInPh1MlFrMngProt | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.13 | ||
| This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtInPh1MlConnectionTyp = sameNetManaged, this object will be RO (internally determined). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), lmi(3), ansiT1(4), annexA(5) | ||
| prtInPh1MlEnqPeriod | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.14 | ||
| This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..30 | ||
| prtInPh1MlFullRptPeriod | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.15 | ||
| This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite (never sent). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| prtInPh1MlFrWindowSize | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.16 | ||
| This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| prtInPh1MlErrorsThreshold | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.17 | ||
| This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtInPh1MlFrMngProt is NOT (notApplicable or none). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| prtInPh1MlMaxIdleTime | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.18 | ||
| Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=Never. Never move to higher prioritized connected link. UNIT is seconds. Valid values are: 0, 1, 2, 3, 4, 5, 10, 20, 30, 40, 50, 60, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 1200, 1500, 1800. Attempt to Set an invalid value will result in getting the default value. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..1800 | ||
| prtInPh1MlBearerCh | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.19 | ||
| Defines which B (bearer) channels are used for transferring ISDN data. Default value is: none (255). anyChannel (2) is skipped because it is not in use here. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), channelB1(3), channelB2(4), chB1andchB2(5), none(255) | ||
| prtInPh1MlAssociatedExCh | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.20 | ||
| This object indicates the external port associated to this internal port. At present, it is used by the Hybrid (mp2100h), MHS-4 cards which can have up to 64 dynamic internal ports associated with External ports. For ISDN cards, the value will be: notApplicable (255). The associated external of an ISDN internal port is represented by the MIB object: prtIsdnDirectoryPrtNu. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), notApplicable(255) | ||
| prtInPh1MlClockEncoding | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.21 | ||
| This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), nrz(2), nrzI(3), fm0(4), manchester(5), diffManchester(6) | ||
| prtInPh1MlMinSeparators | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.22 | ||
| Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable | |||
| OBJECT-TYPE | |||
| Integer32 | 0..16 | ||
| prtInPh1MlCcittCrc | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.23 | ||
| This object indicates how many Bits are used for CRC (HDLC item). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), crc16(2), crc32(3) | ||
| prtInPh1MlFrameSeparator | 1.3.6.1.4.1.164.3.2.3.2.2.3.1.24 | ||
| This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), idles(2), flags(3) | ||
| prtInPh1MlDlciTable | 1.3.6.1.4.1.164.3.2.3.2.2.4 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInPh1MlDlciEntry | |||
| prtInPh1MlDlciEntry | 1.3.6.1.4.1.164.3.2.3.2.2.4.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInPh1MlDlciEntry | |||
| prtInPh1MlDlciCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInPh1MlDlciSltIdx | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInPh1MlDlciPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.3 | ||
| This attribute indicates a unique internal port number. MPH.1/E1 and MPH.1/T1 cards have three internal ports. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101), inPrt2(102), inPrt3(103) | ||
| prtInPh1MlDlciIdx | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.4 | ||
| This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, then its type is 'user' and the only valid index is 1. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtInPh1MlDlciValid | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.5 | ||
| This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInPh1MlDlciIConSlt | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.6 | ||
| This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInPh1MlDlciIConPrt | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.7 | ||
| This attribute indicates a unique port id which the dlci is routed to. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), clNMS(99), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112) | ||
| prtInPh1MlDlciIConDlci | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.8 | ||
| This attribute indicates a unique internal connection dlci number which the src dlci is routed to. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtInPh1MlDlciTxBc | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.9 | ||
| This attribute indicates a unique Tx committed bandwidth on the user transmit line or at the port receive line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBc9600bps(3), txBc14200bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21) | ||
| prtInPh1MlDlciTxBe | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.10 | ||
| This attribute indicates a unique Tx excess bandwidth on the user transmit line or at the port receive line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBe9600bps(3), txBe14200bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21) | ||
| prtInPh1MlDlciRxBc | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.11 | ||
| This attribute indicates a unique Rx committed bandwidth on the user receive line or at the port transmit line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBc9600bps(3), rxBc14200bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21) | ||
| prtInPh1MlDlciRxBe | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.12 | ||
| This attribute indicates a unique Rx excess bandwidth on the user receive line or at the port transmit line. | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBe9600bps(3), rxBe14200bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21) | ||
| prtInPh1MlDlciPriority | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.13 | ||
| This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| prtInPh1MlDlciStatus | 1.3.6.1.4.1.164.3.2.3.2.2.4.1.14 | ||
| This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected | |||
| OBJECT-TYPE | |||
| INTEGER | disconnected(1), connected(2) | ||
| prtPhMlCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.2.5 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtPhMlCnfgEntry | |||
| prtPhMlCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.2.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtPhMlCnfgEntry | |||
| prtPhMlCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtPhMlSltIdx | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtPhMlPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.3 | ||
| This attribute indicates a unique port number. ML-20 cards have just one external interface. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtPhMlConnect | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtPhMlRate | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r2x64eq128Kbps(4), r3x64eq192Kbps(6), r4x64eq256Kbps(8), r5x64eq320Kbps(10), r6x64eq384Kbps(12), r7x64eq448Kbps(14), r8x64eq512Kbps(16), r9x64eq576Kbps(18), r10x64eq640Kbps(20), r11x64eq704Kbps(22), r12x64eq768Kbps(24), r13x64eq832Kbps(26), r14x64eq896Kbps(28), r15x64eq960Kbps(30), r16x64eq1024Kbps(32), r17x64eq1088Kbps(34), r18x64eq1152Kbps(36), r19x64eq1216Kbps(38), r20x64eq1280Kbps(40), r21x64eq1344Kbps(42), r22x64eq1408Kbps(44), r23x64eq1472Kbps(46), r24x64eq1536Kbps(48), r25x64eq1600Kbps(50), r26x64eq1664Kbps(52), r27x64eq1728Kbps(54), r28x64eq1792Kbps(56), r29x64eq1856Kbps(58), r30x64eq1920Kbps(60), r31x64eq1984Kbps(62) | ||
| prtPhMlCAS | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.6 | ||
| This attribute indicates whether Channel Associated Signaling (CAS) is used. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtPhMlClockMode | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.7 | ||
| Clock mode. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(2), ext-dce(3), dte(4) | ||
| prtPhMlSatBuffer | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.8 | ||
| Satellite Buffer (+/- 256). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtPhMlDialProcess | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.9 | ||
| Dial Process. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), callIn(3), callOut(4) | ||
| prtPhMlSyncRestore | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.10 | ||
| Sync Restoration time, in seconds. notApplicable=0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| prtPhMlBus | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.11 | ||
| The TDM BUS this port is linked to. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), busA(2), busB(3) | ||
| prtPhMlMfSyncSlot | 1.3.6.1.4.1.164.3.2.3.2.2.5.1.12 | ||
| This attribute indicates whether the sync is synchronized according to a certain card and the slot of this card. This operation is required in order to bypass signaling of PCM voice channels. In the ?004 Unit the entries io6(10)..io12(16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | none(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtPhPlCnfg | 1.3.6.1.4.1.164.3.2.3.2.3 | ||
| OBJECT IDENTIFIER | |||
| prtExPhPlCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.3.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPhPlCnfgEntry | |||
| prtExPhPlCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPhPlCnfgEntry | |||
| prtExPhPlCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPhPlSltIdx | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPhPlPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.3 | ||
| This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtExPhPlConnect | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPhPlHRate | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.5 | ||
| This attribute indicates the port speed for HIGH speed cards. The card has limitations about the maximum sigma channel speeds and about the possible rates for each clock mode . N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. 'r9d6KbpsNLE' means rate of 9.6 Kbps ('d'=dot). Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r2048KbpsE (63), -- r2048KbpsNLE | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r32KbpsNLE(2), r48KbpsNLE(3), r56KbpsNLE(4), r64KbpsNLE(5), r112KbpsNLE(6), r128KbpsNLE(7), r168KbpsNLE(8), r192KbpsNLE(9), r224KbpsNLE(10), r256KbpsNLE(11), r280KbpsE(12), r320KbpsE(13), r336KbpsNLE(14), r384KbpsNLE(15), r392KbpsE(16), r448KbpsNLE(17), r504KbpsLE(18), r512KbpsE(19), r560KbpsE(20), r576KbpsLE(21), r616KbpsE(22), r640KbpsE(23), r672KbpsNLE(24), r704KbpsE(25), r728KbpsE(26), r768KbpsNLE(27), r784KbpsE(28), r832KbpsE(29), r840KbpsE(30), r896KbpsNLE(31), r952KbpsE(32), r960KbpsE(33), r1008KbpsLE(34), r1024KbpsE(35), r1064KbpsE(36), r1088KbpsE(37), r1120KbpsE(38), r1152KbpsLE(39), r1176KbpsE(40), r1216KbpsE(41), r1232KbpsE(42), r1280KbpsE(43), r1288KbpsE(44), r1344KbpsNLE(45), r1400KbpsE(46), r1408KbpsE(47), r1456KbpsE(48), r1472KbpsE(49), r1512KbpsE(50), r1536KbpsE(51), r1568KbpsE(52), r1600KbpsE(53), r1624KbpsE(54), r1664KbpsE(55), r1680KbpsE(56), r1728KbpsE(57), r1736KbpsE(58), r1792KbpsNLE(59), r1856KbpsE(60), r1920KbpsE(61), r1984KbpsE(62), r2048KbpsE(63), r9d6KbpsNLE(65), r14d4KbpsNLE(66), r16KbpsNLE(67), r19d2KbpsNLE(68), r28d8KbpsNLE(69), r38d4KbpsNLE(70), r57d6KbpsNLE(71), r115d2KbpsNLE(72), r24000bps(73) | ||
| prtExPhPlLRate | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.6 | ||
| This attribute indicates the port speed for LOW speed cards. The card has limitations about the possible rates for each clock mode. N - The rate is valid for DCE and EXT-DCE Nodal clock mode. L - The rate is valid for DCE and EXT-DCE Local clock mode. E - The rate is valid for DTE External clock mode. Note: Some rate attributes have been changed. As the MIB was already released with the old attributes, the names of the options were not changed. The new names + attributes are in a comment. Example: r57600bpsLE (16), -- r57600bpsNLE | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r300bpsNLE(2), r600bpsNLE(3), r800bpsNLE(4), r1200bpsNLE(5), r2400bpsNLE(6), r4800bpsNLE(7), r9600bpsNLE(8), r14400bpsLE(9), r19200bpsNLE(10), r28800bpsLE(11), r32000bpsNLE(12), r38400bpsNLE(13), r48000bpsNLE(14), r56000bpsNLE(15), r57600bpsLE(16), r64000bpsNLE(17), r112000bps(18), r115200bps(19), r16000bpsNLE(20), r100bpsNLE(21), r128000bps(22), r24000bps(23) | ||
| prtExPhPlProtocol | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.7 | ||
| This object indicates the applied protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | fr(1), frPlus(2), pCellRelay(3), hdlcSdlc(4), transparentHdlc(5), async(6), asyncReliable(7), activePPP(8), slip(9), pppAgent(10), slipAgent(11), transparent(12), sna(13) | ||
| prtExPhPlConnectionTyp | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.8 | ||
| This attribute indicates the link connection type. It is required for three reasons: FR/CR Inband management opration (LMI,CLMM...). CIR check. NMS network management. SameNetManaged - indicates network internal line. SameNetMotMana - indicates network internal line, but the remote mux is not managed by the NMS. User - User to Network Interface. OtherNet - Network To Network Interface. PubNet - Access Mux To PubNet Interface. | |||
| OBJECT-TYPE | |||
| INTEGER | sameNetManaged(1), sameNetNotMana(2), user(3), otherNet(4), pubNet(5), notApplicable(255) | ||
| prtExPhPlClkMode | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.9 | ||
| Clock mode. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), extDce(2), dte(3), int(4), lbt(5) | ||
| prtExPhPlDceClkSrc | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.10 | ||
| This attribute indicates the source of the clock when working in dce or ext-dce clock mode. notApplicable(1) - is applied for dte(3) and lbt(5) clock modes. When clock mode is dte, the clock source is always external, therefore this object's value is notApplicable. local(2) and nodalTiming(3) - are valid in dce(1), extDce(2) or int(4) clock modes. The recommended clock source is local(2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), nodalTiming(3) | ||
| prtExPhPlCongResponse | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.11 | ||
| This attribute indicates how to handle the congestion indication to/from the mux internal connection side (for example transmit/received becn to/from the network). no - do nothing flowControl - translates the congestion indication between the port and the internal connection port according to the definition of the prtInPh1MlFlowControl parameters. The operation is done on both directions. toFlowControl- translates the backward congestion indication received from the internal connection port (normally the network side) to flow control and do nothing in the other direction. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), flowControl(3), toFlowControl(4) | ||
| prtExPhPlCongLevel | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.12 | ||
| This attribute indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5 percent. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..70 | ||
| prtExPhPlTc | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.13 | ||
| This attribute indicates the Tc parameter which is the time period of the sliding window in which the Bc/Be are tested. The value of this parameter is identical for all the ports of a specific card . | |||
| OBJECT-TYPE | |||
| INTEGER | tc1sec(1), tc2sec(2), tc3sec(3), tc4sec(4), notApplicable(255) | ||
| prtExPhPlFlowControl | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.14 | ||
| This attribute indicates the required flow control betweeen the port and the remote equipment. fecnBecn - is valid only for FR, FR+ and CR protocols. xonXoff,dtrCts - are valid only for Async protocols. speedReduction - is valid only for DLC protocol when the Clock Mode is DCE and the Clock Source is Local. | |||
| OBJECT-TYPE | |||
| INTEGER | none(2), fecnBecn(3), xonXoff(4), dtrCts(5), speedReduction(6) | ||
| prtExPhPlDcdRts | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.15 | ||
| Protocol may require end to end connect indication over the network. End to end link connection establishment over the FR network will be indicated to the user by using DCD or RTS control signals, depending on the clock mode: DCE or DTE respectively. The options are : - On : DCD(DCE)/RTS(DTE) will be constantly ON no matter if the End to End connection is established or not. - End to End: The DCD(DCE)/RTS(DTE) will be according to the status of the End to End connection. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), endToEnd(3) | ||
| prtExPhPlDcdRtsControlPath | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.16 | ||
| Protocol may require end to end connect indication over the network. This parameter defines whether to take the user connection status (RTS(DCE)/DCD(DTE)) and forward it to the network side. - on : Transmit active connection to the network regardless the RTS/DCD control lines status. - off: Transmit active connection to the network according to the status of the RTS/DCD pin. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtExPhPlDataBits | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.17 | ||
| This attribute indicates the number of data bits in async frame. It is relevant only for Async protocols. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dataBits7Bits(2), dataBits8Bits(3) | ||
| prtExPhPlParity | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.18 | ||
| This attribute indicates the parity operation mode in async frame. It is relevant only for Async protocols. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), odd(2), even(3), none(4) | ||
| prtExPhPlStopBits | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.19 | ||
| This attribute indicates the minimum number of stop bits in the tx async frame. It is relevant only for Async protocols. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), sb1Bit(2), sb1dot5Bits(3), sb2Bits(4) | ||
| prtExPhPlLXon | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.20 | ||
| This attribute indicates the character used as X-On to notify receive enable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPhPlLXoff | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.21 | ||
| This attribute indicates the character used as X-Off to notify receive disable. This parameter is valid only for async protocols. Valid values: 0..255. The value 256 indicates that it's not applicable | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPhPlFrMngProt | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.22 | ||
| This object indicates the Frame-Relay management protocol. ansiT1 = ANSI T1.617 Annex D (this is the default value). This parameter is applicable only for FR and FR+ protocols. When prtExPhPlConnectionTyp = sameNetManaged, this object will be RO (internally determined). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), lmi(3), ansiT1(4), annexA(5) | ||
| prtExPhPlEnqPeriod | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.23 | ||
| This object is the Status Enquiry Period, in seconds. It determines the frequency of the Status Enquiry message as sent by the FR user side. At the FR network side, it determines the timeout for this message reception. Default = 4 seconds. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..30 | ||
| prtExPhPlFullRptPeriod | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.24 | ||
| This object is the Full Report Frequency. It determines the number of the Status Enquiry messages sent by the FR user side, before a Full Report Request is sent. The units are : Status Enquiry messages (periods). Valid values: 1 .. 255. 255 = infinite. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPhPlFrWindowSize | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.25 | ||
| This object is the FR Window Size. It determines the number of samplings in the sliding window that counts the errors. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| prtExPhPlErrorsThreshold | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.26 | ||
| This object is the Max Errors. It determines the number of Status Enquiry Errors that occured within the FR sliding window, before this port is considered DOWN (threshold). This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| prtExPhPlPvcCreateMsg | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.27 | ||
| This object is Update Message (if required or not). It determines whether a message of a New PVC Creation is requested or not (yes/no). Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPhPlCllmMsg | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.28 | ||
| This object is CLLM Message (if required or not). It determines whether to send (or not) a congestion message when the port is Rx congested. Default = no. This parameter is applicable only for FR and FR+ protocols AND only when prtExPhPlFrMngProt is NOT (notApplicable or none). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPhPlProtDelayLevel | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.29 | ||
| This object is the Segmentation in Bytes. In some cases, the enumerated values will mean other segmentation values than specified: Product: MX-3000 MX-3000 MX-300/MX-30 Protocol: FR+ Transparent FR+ ----------------------------------------------------- level 1 50 Bytes 44 Bytes 50 Bytes level 2 158 Bytes 155 Bytes 158 Bytes level 3 266 Bytes 266 Bytes 266 Bytes level 4 376 Bytes 377 Bytes 376 Bytes level 5 484 Bytes 488 Bytes 484 Bytes Defval=level 1 value This parameter is applicable only for FR+ and transparent protocols. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), s36Byte(2), s150Byte(3), s264Byte(4), s378Byte(5), s492Byte(6) | ||
| prtExPhPlClockEncoding | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.30 | ||
| This object is the Encoding type of the Line. This parameter is applicable only for FR and FR+ protocols. For MAXCESS 3000 & MP2100H: when setting to nrzI (3) the nrzI works as nrzI Mark. For MAXCESS 30/300 when setting to nrzI (3) the nrzI works as nrzI Space. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), nrz(2), nrzI(3), fm0(4), manchester(5), diffManchester(6), nrzISpace(7), nrzIMark(8) | ||
| prtExPhPlMinSeparators | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.31 | ||
| Minimum number of bytes separating between two adjacent frames (HDLC item). 0 = notApplicable | |||
| OBJECT-TYPE | |||
| Integer32 | 0..16 | ||
| prtExPhPlCcittCrc | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.32 | ||
| This object indicates how many Bits are used for CRC (HDLC item). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), crc16(2), crc32(3) | ||
| prtExPhPlFrameSeparator | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.33 | ||
| This object indicates what should be transferred on the line when there are no frames to pass (HDLC item). idles: mean that FF will pass on the line flags: mean that 7E will pass on the line. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), idles(2), flags(3) | ||
| prtExPhPlIdleCode | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.34 | ||
| Determines the code for transmission when there are no frames to transmit on the line. The value should be 0 to FFH. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPhPlJitter | 1.3.6.1.4.1.164.3.2.3.2.3.1.1.35 | ||
| Maximum variant delay of the FR network, in msec. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..1000 | ||
| prtExPhPlDlciTable | 1.3.6.1.4.1.164.3.2.3.2.3.2 | ||
| The write operation into the Table Objects is valid only at the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPhPlDlciEntry | |||
| prtExPhPlDlciEntry | 1.3.6.1.4.1.164.3.2.3.2.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPhPlDlciEntry | |||
| prtExPhPlDlciCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPhPlDlciSltIdx | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPhPlDlciPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.3 | ||
| This attribute indicates a unique internal port number. PH.1/E1 and PH.1/T1 cards have three internal ports. Stand-alone units may have six such ports. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtExPhPlDlciIdx | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.4 | ||
| This attribute indicates a unique index for each possible used dlci(16..991). When the protocol is not Multiplexing protocol, its type is 'user' and the only valid index is 1. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtExPhPlDlciValid | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.5 | ||
| This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPhPlDlciIConSlt | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.6 | ||
| This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. cl - will represent any of the CL slots. This value can be selected for multiple DLCIs of the product. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPhPlDlciIConPrt | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.7 | ||
| This attribute indicates a unique port id which the dlci is routed to. clNMS - will be used for NMS SNMP messages. It can be any port of the CL card. This value will be selectable only if prtExPhPlDlciIConSlt='cl' or 'notApplicable'. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), clNMS(99), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110) | ||
| prtExPhPlDlciIConDlci | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.8 | ||
| This attribute indicates a unique internal connection dlci number, the dlci is routed to. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtExPhPlDlciTxBc | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.9 | ||
| This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBc9600bps(3), txBc14400bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21), txBc16000bps(25), txBc112Kbps(26) | ||
| prtExPhPlDlciTxBe | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.10 | ||
| This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBe9600bps(3), txBe14400bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21), txBc16000bps(25), txBc112Kbps(26) | ||
| prtExPhPlDlciRxBc | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.11 | ||
| This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBc9600bps(3), rxBc14400bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26) | ||
| prtExPhPlDlciRxBe | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.12 | ||
| This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBe9600bps(3), rxBe14400bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26) | ||
| prtExPhPlDlciPriority | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.13 | ||
| This attribute indicates a unique priority of the pcv. 1 is the lowest priority and 8 is the highest priority. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| prtExPhPlDlciStatus | 1.3.6.1.4.1.164.3.2.3.2.3.2.1.14 | ||
| This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected | |||
| OBJECT-TYPE | |||
| INTEGER | disconnected(1), connected(2) | ||
| prtExPhPlModemTable | 1.3.6.1.4.1.164.3.2.3.2.3.3 | ||
| External Modem Parameters. The write operation into the Table Objects is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPhPlModemEntry | |||
| prtExPhPlModemEntry | 1.3.6.1.4.1.164.3.2.3.2.3.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPhPlModemEntry | |||
| prtExPhPlModemCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPhPlModemSltIdx | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPhPlModemPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.3 | ||
| This attribute indicates a unique port number. In case of PH.1 card, only exPrt(1) is valid. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6) | ||
| prtExPhPlModemStatus | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.4 | ||
| This object indicates whether a Dial Up Modem is enabled on this port. Default: disable | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| prtExPhPlModemActivate | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.5 | ||
| This object indicates whether the Dial Up Modem is activated when the first frame is received or it is always activated. Default: onFirstFrame | |||
| OBJECT-TYPE | |||
| INTEGER | onFirstFrame(2), always(3), notApplicable(255) | ||
| prtExPhPlModemMaxIdleTime | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.6 | ||
| Max Time allowed in Seconds without any traffic before the line is disconnected. Legal Values are: 1 sec, 2 sec .. 5 sec, 10 sec, 20 sec.. 1 min, 2 min .. 10 min, 15 min, 20 min, 25 min, 30 min. 65535 sec. means that this parameter is not applicable. Default: 1 sec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPhPlModemTimeBtwnCalls | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.7 | ||
| Minimum Time in Seconds which is required after a call was disconnected. In this time no other call will be initiated from this Modem port even if there were frames transmitted to this port. This time is required for some Modems which have initializations that take a few seconds. Legal Values are: 0 sec. - 30 sec., 1-5 min. 65535 sec. means that this parameter is not applicable. Default: 0 sec | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPhPlModemCallDelay | 1.3.6.1.4.1.164.3.2.3.2.3.3.1.8 | ||
| Time in Seconds that the device will wait before dialing to the remote device. This feature is mostly used when there is a backup modem to the main link and the main link is down. In this case it is important to prevent the 2 devices from dialing through the backup modems to each other at the same time. It is advised to configure one side with a small call delay and the other side with a large call delay. Legal Values are: 0 - 30, 60, 120, 180, 240, 300, 600, 900, 1200, 1500, 1800 . 65535 sec. means that this parameter is not applicable. Default: 0 sec | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtLs2Cnfg | 1.3.6.1.4.1.164.3.2.3.2.4 | ||
| OBJECT IDENTIFIER | |||
| prtExLs2CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.4.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExLs2CnfgEntry | |||
| prtExLs2CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExLs2CnfgEntry | |||
| prtExLs2CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExLs2SltIdx | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExLs2PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.3 | ||
| This attribute indicates a unique port index. For the Ls2/X.58 exPrt(7)..exPrt(10) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10) | ||
| prtExLs2Connect | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExLs2Rate | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.5 | ||
| Port rates. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(2), r4800bps(3), r9600bps(4), r19200bps(5) | ||
| prtExLs2ClkMode | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.6 | ||
| This attribute indicates a unique port operation clock mode. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), ext-dce(2), dte(3) | ||
| prtExLs2Cts | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.7 | ||
| CTS. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), rts-min(3), rts-max(4) | ||
| prtExLs2Dcd | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.8 | ||
| DCD. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), card-sync(3) | ||
| prtExLs2EnvIdx | 1.3.6.1.4.1.164.3.2.3.2.4.1.1.9 | ||
| Envelope Index. When prtInLs2EnvAssign=auto, the value is 0 (not applicable). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..24 | ||
| prtInLs2CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.4.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInLs2CnfgEntry | |||
| prtInLs2CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.4.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInLs2CnfgEntry | |||
| prtInLs2CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInLs2SltIdx | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInLs2PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.3 | ||
| This attribute indicates a unique internal port index. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101), inPrt2(102) | ||
| prtInLs2Connect | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInLs2Group | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.5 | ||
| This attribute indicates the group number of the port. LS-2 internal ports with the same group number share the same Time slot of the main link | |||
| OBJECT-TYPE | |||
| Integer32 | 1..12 | ||
| prtInLs2Member | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.6 | ||
| This attribute indicates the group member id of the port. This parameter is for the automatic envelope assignment algorithm. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| prtInLs2LinkTo | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.7 | ||
| It indicates the slot of the main link card to which the LS2 card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInLs2EnvAssign | 1.3.6.1.4.1.164.3.2.3.2.4.2.1.8 | ||
| Envelope assignment type. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(2), manual(3) | ||
| prtVc2CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.5 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtVc2CnfgEntry | |||
| prtVc2CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtVc2CnfgEntry | |||
| prtVc2CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.5.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtVc2SltIdx | 1.3.6.1.4.1.164.3.2.3.2.5.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. For Stand Alone products like WR: notApplicable (255) | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtVc2PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.5.1.3 | ||
| A unique identifier of the port, within the card. For Megaplex card ports, Web Ranger and FCD-IP Voice ports the values will be: exPrt1 (1) exPrt2 (2) exPrt3 (3) exPrt4 (4) exPrt5 (5) exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) exPrt10 (10) exPrt11 (11) exPrt12 (12) exPrt13 (13) exPrt14 (14) exPrt15 (15) exPrt16 (16) For LA-240: The index for fixed voice ports will be - exPrt6 (6) exPrt7 (7) exPrt8 (8) exPrt9 (9) The index for voice card ports will be - Slot number * 100 + ch (for IO-1: 101..104, for IO-2: 201..204). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVc2Connect | 1.3.6.1.4.1.164.3.2.3.2.5.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3), v51(4) | ||
| prtExVc2TransGain | 1.3.6.1.4.1.164.3.2.3.2.5.1.5 | ||
| Transmit gain in dBm. For ports of VC-6A, VC-6AG, VC-8 and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVc2ReceiveGain | 1.3.6.1.4.1.164.3.2.3.2.5.1.6 | ||
| Receive gain in dBm. For ports of VC-6A, VC-6AG, VC-8 and VC-16 cards, the units will be 0.1dBm because valid values can be in 0.5dBm steps. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVc2Wire | 1.3.6.1.4.1.164.3.2.3.2.5.1.7 | ||
| For some cards, this object is equal for all the ports in the specific card because of HW limitations. For FXO & FXS this parameter is not applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | w2wire(1), w4wire(2), notApplicable(255) | ||
| prtExVc2CodingLaw | 1.3.6.1.4.1.164.3.2.3.2.5.1.8 | ||
| This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations | |||
| OBJECT-TYPE | |||
| INTEGER | aLAW(1), uLAW(2) | ||
| prtExVc2Sig | 1.3.6.1.4.1.164.3.2.3.2.5.1.9 | ||
| This attribute indicates the method for decoding/encoding the signaling information(on/off hook). noSignaling (1) - not using signaling (only voice). robbedBitMultiFrame(2) - is the standard method for T1 links and proprietary method for E1 links. chAssociatedE1 (3) - is valid only for E1 G.732S links. robbedBitFrame (4) - is proprietary method implimenting 7 bit for the voice and 1 bit dedicated for signaling. For some cards, this object is equal for all the ports in the specific module because of HW limitations. | |||
| OBJECT-TYPE | |||
| INTEGER | noSignaling(1), robbedBitMultiFrame(2), chAssociatedE1(3), robbedBitFrame(4) | ||
| prtExVc2Oos | 1.3.6.1.4.1.164.3.2.3.2.5.1.10 | ||
| This object is equal for all the ports in the specific card because of HW limitations | |||
| OBJECT-TYPE | |||
| INTEGER | forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4), notApplicable(5) | ||
| prtExVc2LinkTo | 1.3.6.1.4.1.164.3.2.3.2.5.1.11 | ||
| This attribute indicates the slot of the ML card to which the VC card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExVc2OperMode | 1.3.6.1.4.1.164.3.2.3.2.5.1.12 | ||
| This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(2), unidirectRx(3), broadcast(4) | ||
| prtExVc2SigProfile | 1.3.6.1.4.1.164.3.2.3.2.5.1.13 | ||
| This object indicates the Signaling Profile of the port. notApplicable - for VC-2 family and when prtExVc2Sig=noSignaling(1) p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), manual(2), p1(3), p2(4), p3Fxo3S3(5), reversePolarity(6), meteringPulse(7), p4(8) | ||
| prtExVc2CallEnable | 1.3.6.1.4.1.164.3.2.3.2.5.1.14 | ||
| This object indicates the Enabled Call direction. notApplicable - for all cards except VC-2/R2. both - incoming + outgoing. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), incoming(2), outgoing(3), both(4) | ||
| prtExVc2R2Delay | 1.3.6.1.4.1.164.3.2.3.2.5.1.15 | ||
| This object indicates the R2 Delay. notApplicable - for all cards except VC-2/R2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), terrestrial(2), satellite(3) | ||
| prtExVc2CasStd | 1.3.6.1.4.1.164.3.2.3.2.5.1.16 | ||
| This object indicates the CAS (Channel Associated Signaling) Standard. notApplicable - for all cards except VC-2/R2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r2Q422(2), specialA(3), specialB(4), specialC(5), specialD(6), specialE(7), specialF(8), specialG(9) | ||
| prtExVc2EchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.5.1.17 | ||
| Echo canceler activation. notApplicable - for VC-2 and VC-6 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtExVc2IfType | 1.3.6.1.4.1.164.3.2.3.2.5.1.18 | ||
| Interface Type. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), w2Em(2), w4Em(3), fxo(4), fxs(5) | ||
| prtExVc2Encoding | 1.3.6.1.4.1.164.3.2.3.2.5.1.19 | ||
| Voice Encoding Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), pcm(2), adpcm(3) | ||
| prtExVc2TxBitCode | 1.3.6.1.4.1.164.3.2.3.2.5.1.20 | ||
| - - - For MP & FCD - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = M lead 2 hex = 0010 = M lead inverse 3 hex = 0011 = Reverse Polarity 4 hex = 0100 = Metering Pulse 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For WR II - - - This object represents the following 4 parameters by 2 Octets: 1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1). 2. Default signaling bits that are not in use (nibble 2). 3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3). 4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook Default sig. Ring Detect. M (Mouth) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable 1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit 2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv. 3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit 4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv. 5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid 6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid 7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid 8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid 9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid C-F hex not used-invalid ABCD not Used-invalid not Used-invalid Default value: 11 11 | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtExVc2RxBitOutput | 1.3.6.1.4.1.164.3.2.3.2.5.1.21 | ||
| - - - For MP (VC-Q card only) & FCD - - - This object represents 3 parameters by 2 Octets: Spare -MSB nibble, always=0 hex E Lead Output - nibble, Reverse Polarity Output- nibble, Metering Pulse Output -LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = Rx A bit 2 hex = 0010 = Rx A bit inverse 3 hex = 0011 = Rx B bit 4 hex = 0100 = Rx B bit inverse 5 hex = 0101 = Rx C bit 6 hex = 0110 = Rx C bit inverse 7 hex = 0111 = Rx D bit 8 hex = 1000 = Rx D bit inverse 9 hex = 1001 = none A-F hex - not used (invalid values) This object will be RO if prtExVc2SigProfile is NOT manual. - - - For MP (VC-8, VC-16, VC-16A cards) - - - This object represents 4 parameters, by 2 Octets : Tx D Bit Code-MSB nibble, Tx C Bit Code- nibble, Tx B Bit Code- nibble, Tx A Bit Code-LSB nibble. Each nibble: 0 hex = 0000 = Not Applicable 1 hex = 0001 = not used (invalid value) 2 hex = 0010 = not used (invalid value) 3 hex = 0011 = not used (invalid value) 4 hex = 0100 = not used (invalid value) 5 hex = 0101 = Forced 1 6 hex = 0110 = Forced 0 7-F hex - not used (invalid values) This object will be RO. - - - For WR II - - - This object represents the following 2 parameters in 1 Octet: 1. On/Off hook signaling receive mode from the T1/E1 into the FXS/FXO (MSB nibble 1). 2. E (Ear) Signaling receive mode from the T1/E1 into the E&M (LSB nibble 2). Each nibble: --------------------------------------------------------------------------------------- Value On/Off Hook E (Ear) --------------------------------------------------------------------------------------- 0 hex = 0000 Not Applicable Not Applicable 1 hex = 0001 Rx A bit Rx A bit 2 hex = 0010 Rx A bit inverse Rx A bit inverse 3 hex = 0011 Rx B bit Rx B bit 4 hex = 0100 Rx B bit inverse Rx B bit inverse 5-F hex not used-invalid not Used-invalid Default value: 11 | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtExVc2MeterRate | 1.3.6.1.4.1.164.3.2.3.2.5.1.22 | ||
| This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS. Meter Rate means rate of Call Meter in Public Phones, in KHz units. For some cards, the value must be the same for all card's ports. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r16Khz(2), r12Khz(3) | ||
| prtExVc2IfSignaling | 1.3.6.1.4.1.164.3.2.3.2.5.1.23 | ||
| This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS, VC-16/FXO and VC-16/FXS cards. Interface Analog Signaling. Must be the same for all card's ports. loopStart - for the usual trunk/phone types. groundStart - for trunks that need Ground signaling . winkStart - for trunks that need Reverse Polarity. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), loopStart(2), groundStart(3), winkStart(4) | ||
| prtExVc2SeizeAck | 1.3.6.1.4.1.164.3.2.3.2.5.1.24 | ||
| This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Default value for WR FXO: no(2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExVc2EandMType | 1.3.6.1.4.1.164.3.2.3.2.5.1.25 | ||
| This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), type1(2), type2(3), type3(4), type5(5) | ||
| prtExVc2RemType | 1.3.6.1.4.1.164.3.2.3.2.5.1.26 | ||
| Remote Type. Applicable for VC-6A/4LB card & for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 . | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), lb(2), pbx(3), e1(4), t1(5), t1D4(6) | ||
| prtExVc2ConvTime | 1.3.6.1.4.1.164.3.2.3.2.5.1.27 | ||
| Conversation Time in minutes. Applicable for VC-6A/4LB card. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), m2(2), m3(3), m5(4), unlimited(5) | ||
| prtExVc2SigFeedback | 1.3.6.1.4.1.164.3.2.3.2.5.1.28 | ||
| Signaling Feedback. Applicable for VC-8/FXO and VC-16/FXO cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExVc2EchoCancelerModule | 1.3.6.1.4.1.164.3.2.3.2.5.1.29 | ||
| This parameter indicates whether Echo canceler module exists for this port. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), notExist(2), exist(3) | ||
| prtHsfCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.6 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtHsfCnfgEntry | |||
| prtHsfCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.6.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtHsfCnfgEntry | |||
| prtHsfCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.6.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relate to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtHsfSltIdx | 1.3.6.1.4.1.164.3.2.3.2.6.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtHsfPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.6.1.3 | ||
| This attribute indicates a unique external port index. Hs2 has only two ports (exPrt1,exPrt2). Hs3 has three ports (exPrt1,exPrt2,exPrt3). Hsq and hsqN has four ports. Hs6 has six external ports. Hs12 has twelve external ports. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12) | ||
| prtExHsfConnect | 1.3.6.1.4.1.164.3.2.3.2.6.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExHsfRate | 1.3.6.1.4.1.164.3.2.3.2.6.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), r32Kbps(63) | ||
| prtExHsfClkMode | 1.3.6.1.4.1.164.3.2.3.2.6.1.6 | ||
| This attribute indicates a unique port operation clock mode. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), ext-dce(2), dte(3), none(4) | ||
| prtExHsfCts | 1.3.6.1.4.1.164.3.2.3.2.6.1.7 | ||
| This attribute indicates a unique CTS control line operation mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), rts(3) | ||
| prtExHsfFifoSize | 1.3.6.1.4.1.164.3.2.3.2.6.1.8 | ||
| Size in bits. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(2), s16bits(3), s30bits(4), s52bits(5), s72bits(6) | ||
| prtExHsfLinkTo | 1.3.6.1.4.1.164.3.2.3.2.6.1.9 | ||
| This attribute indicates a slot of Main Link module, that the port is linked to. This object is the same for all the ports in the specific card because of HW limitations. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHsfOperMode | 1.3.6.1.4.1.164.3.2.3.2.6.1.10 | ||
| This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(2), unidirectRx(3), broadcast(4) | ||
| prtExHsfInbandLoopback | 1.3.6.1.4.1.164.3.2.3.2.6.1.11 | ||
| This object indicates if Inband Loopback from the Network should be enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), ft1Enabled(3) | ||
| prtExHsfClkPolarity | 1.3.6.1.4.1.164.3.2.3.2.6.1.12 | ||
| This object indicates the clock polarity. For FCD-M this object will be applicable only for the fixed HS port (the fixed port on the device). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), normal(2), invert(3) | ||
| prtExHsfControlSignal | 1.3.6.1.4.1.164.3.2.3.2.6.1.13 | ||
| This object indicates the Control Signal according to G.797 ITU-T standard. For FCD-M this object will be applicable for the fixed HS port (the fixed port on the device) and HS-Q/N channels. Local and End to End are applicable only when channel Interface type is RS-530, else it will be Not Applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), endToEnd(3) | ||
| prtHs4Cnfg | 1.3.6.1.4.1.164.3.2.3.2.7 | ||
| OBJECT IDENTIFIER | |||
| prtExHs4CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.7.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExHs4CnfgEntry | |||
| prtExHs4CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.7.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExHs4CnfgEntry | |||
| prtExHs4CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExHs4SltIdx | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHs4PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExHs4Connect | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithm. It also affects all the module considerations because the card has only one external (physical) interface. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExHs4LineType | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.5 | ||
| This attribute is the line type parameter for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the HS-4/1 and E1 line code parameters for the HS-4/2. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) dsx1ESF (2) dsx1D4 (3) dsx1E1 (4) dsx1E1-CRC (5) dsx1E1-MF (6) dsx1E1-MF-CRC (7) | |||
| OBJECT-TYPE | |||
| INTEGER | esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7) | ||
| prtExHs4LineCode | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.6 | ||
| This attribute is the line code parameter used for T1/E1 interface. The user should select only the parameters relevant to the specific card: T1 line code parameters for the MPH.1/T1 and E1 line code parameters for the MPH.1/E1. This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6) | |||
| OBJECT-TYPE | |||
| INTEGER | b7T1(1), b8zsT1(2), hdb3E1(4) | ||
| prtExHs4LineLen | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.7 | ||
| This attribute is the line length parameter used only for T1 interfaces. len399p533ft=len-399-533ft | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), fcc68(7) | ||
| prtExHs4RestoreT | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.8 | ||
| Time passing from the disappearance of the loss of synchronization condition (red alarm), to the restoration of normal service. | |||
| OBJECT-TYPE | |||
| INTEGER | restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4) | ||
| prtExHs4OosSig | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.9 | ||
| Out of Service signal type. | |||
| OBJECT-TYPE | |||
| INTEGER | notsupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6) | ||
| prtExHs4OosCode | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.10 | ||
| OOS Code | |||
| OBJECT-TYPE | |||
| INTEGER | notsupported(2), oosCode00H(3), oosCode1aH(4), oosCode54H(5), oosCode7eH(6), oosCode7fH(7), oosCode98H(8), oosCode9eH(9), oosCoded5H(10), oosCodee4H(11), oosCodeffH(12) | ||
| prtExHs4IdleCode | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.11 | ||
| Type value(00 - FF HEX), excluding 0H,8H,10H,12H,21H,24H, 42H,49H,84H,92H | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExHs4MfClkSrcSlt | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.12 | ||
| This attribute indicates whether the port Tx is multiframe synchronized with Rx multiframe of another port and the slot position of that port. This opration is required in order to bypass signaling of PCM voice channels. When its value is Local(2) there is no meaning to 'prtExHs4MfClkSrcPrt' parameter. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | local(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHs4MfClkSrcPrt | 1.3.6.1.4.1.164.3.2.3.2.7.1.1.13 | ||
| A unique number to identify a port position in the mux if the MultiFrame clock source is valid (YES). inPrt1 - for MTML-H/E1 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), inPrt1(101) | ||
| prtExHs4TsCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.7.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExHs4TsEntry | |||
| prtExHs4TsEntry | 1.3.6.1.4.1.164.3.2.3.2.7.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExHs4TsEntry | |||
| prtExHs4TsCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExHs4TsSltIdx | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHs4TsPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.3 | ||
| This attribute indicates a unique port number. Hs4/T1 and Hs4/T1 cards have only one external interface. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExHs4TsIdx | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.4 | ||
| This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Card and 1..31 for E1 interface. In G732S-E1 lines, time slot 16 is not valid for data, it is dedicated to multiframe synchronization bits and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExHs4TsIConSlot | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.5 | ||
| This attribute indicates whether the specified time slot is connected/routed internally in the Agent and to which card it is connected. In the ?004 Unit the entries io6(10)..io16) are not valid. split - will be used when the Src TS is connected to more than one slot OR more than one port (each needing less than a whole TS). | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), split(100) | ||
| prtExHs4TsIConPrt | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.6 | ||
| This attribute indicates the internally (In Mux) connected/routed port. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12), noConnect(100) | ||
| prtExHs4TsIConTs | 1.3.6.1.4.1.164.3.2.3.2.7.2.1.7 | ||
| This attribute indicates a unique time slot position. The valid time slots are: 1..24 for T1 Module and 1..31 for E1 interface. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtHsiCnfg | 1.3.6.1.4.1.164.3.2.3.2.8 | ||
| OBJECT IDENTIFIER | |||
| prtExHsiCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.8.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExHsiCnfgEntry | |||
| prtExHsiCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.8.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExHsiCnfgEntry | |||
| prtExHsiCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExHsiSltIdx | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| prtExHsiPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.3 | ||
| A unique port identifier within the card. For MP : 1..12 For DXC: 111 .. 2531. See DXC R6 spec for port index convention. For FCD-A, 'S' Interface external ports: 131, 141, 151, 161. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExHsiConnect | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. v51 - this port is connected to a V5.1 interface. All rest of the values will be 'notApplicable' in this case. V5.1 MIB will be used instead. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3), v51(4) | ||
| prtExHsiRate | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r128kbps(12), notApplicable(255) | ||
| prtExHsiLinkTo | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.6 | ||
| It indicates the slot of the main link card to which the HS-? card is mapped. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHsiInterface | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.7 | ||
| It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. lt1 - for ASMi-31 connection (not ISDN) For MP: For HS-U/I and HS-U/1 only 'lt' and 'nt' are applicable. For HS-S , only 'te' and 'nt' are applicable. For HS-U, this object is not applicable. For HS-U6, HS-U12, are applicable: 'lt'=lt-i,'nt'=nt-i, lt1. For DXC: For HS-U8, HS-U16, are applicable: 'lt'=LT-I,'nt'=NT-I, 'lt1'=LT-1. | |||
| OBJECT-TYPE | |||
| INTEGER | lt(1), nt(2), te(3), lt1(4), notApplicable(255) | ||
| prtExHsiActType | 1.3.6.1.4.1.164.3.2.3.2.8.1.1.8 | ||
| It indicates the Activation Type. Activation Type is the Synchronization type towards the PBX. It is applicable only when prtExHsiInterface=nt. notApplicable - for cards that do not support this object, or when prtExHsiInterface is NOT nt. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), type1(2), type2(3), type3(4) | ||
| prtInHsiCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.8.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. This table is not applicable for MP-2100 HS-U card type. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInHsiCnfgEntry | |||
| prtInHsiCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.8.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInHsiCnfgEntry | |||
| prtInHsiCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.1 | ||
| This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInHsiSltIdx | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.2 | ||
| This object indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| prtInHsiPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.3 | ||
| A unique port identifier within the card. Valid values for MP: inPrt1 (101) .. inPrt48 (148). Valid values for DXC: 11012.. 25316. See DXC R6 spec for port index convention. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtInHsiConnect | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInHsiRate | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.5 | ||
| This object indicates the port speed. For HS-U/I and HS-S ports: 2 bit - up to 9600bps 4 bit - 19200bps 8 bit - 38400bps .. 64kbps. concentrated - this D channel goes to a Concentration channel, that represents many channels that this value was selected for them. The Concentrated channel is an Internal D Channel of the same card. This value is applicable only for D channels, except Concentration channel itself. --for HS-S and HS-U/I cards the Concentration channel will always be: internal-13 --for MP-2200 HS-S12, HS-S6, HS-U12, HS-U6 and DXC HS-U8 and HS-U16 cards, the Concentration channel is selected via the prtInHsiConcentratedTo object. notConnected - same as prtInHsiConnect=no. | |||
| OBJECT-TYPE | |||
| INTEGER | r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r128kbps(12), concentrated(13), notConnected(100), notApplicable(255) | ||
| prtInHsiConcentratedTo | 1.3.6.1.4.1.164.3.2.3.2.8.2.1.6 | ||
| The Concentration D Channel of the prtInHsiPrtIdx port. The port always belongs to the same card as prtInHsiPrtIdx port. This object is applicable only when prtInHsiRate=concentrated. Valid values: - notApplicable: 255 - for MP-2200: HS-S12, HS-U12 cards: inPrt37 (137) .. inPrt48 (148). HS-S6, HS-U6 cards: inPrt19 (119) .. inPrt24 (124). - for DXC: HS-U8 cards: 112 .. 254 HS-U16 cards: 112 .. 258. See DXC R6 spec for port index convention. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPVc4Cnfg | 1.3.6.1.4.1.164.3.2.3.2.9 | ||
| OBJECT IDENTIFIER | |||
| prtExPVc4CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.9.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPVc4CnfgEntry | |||
| prtExPVc4CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.9.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPVc4CnfgEntry | |||
| prtExPVc4CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPVc4SltIdx | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPVc4PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.3 | ||
| This object indicates the port number in the selected card (slot). | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108) | ||
| prtExPVc4PrtType | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.4 | ||
| This object indicates the type of the selected port. In Mx 30/300 phase 4: s0 & u are for Voice over ISDN. In MX 30/300 phase 5: sQsig & uQsig are used for Voice over ISDN with Qsig option. In MX MVC4 voice cards, each pair of ports 1-2, 3-4 may have a different type: E&M, FXO, FXS. In MVC4 compressed voice cards ports 1..4 have the same interface for all ports. In MVC8 compressed voice cards each group of ports 1..4, 5..8 may have a different type: E&M, FXO, FXS. | |||
| OBJECT-TYPE | |||
| INTEGER | eAndM(1), fxo(2), fxs(3), internal(4), s0(5), u(6), sQsig(7), uQsig(8) | ||
| prtExPVc4Connect | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.5 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPVc4IfType | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.6 | ||
| This attribute indicates the interface type of the port. eAndM4wires and eAndM2wires - are valid only for E&M port type eAndM4wires - means 2/4 wires fxoGnd and fxoLoop - are valid only for FXO port type fxsGnd and fxsLoop - are valid only for FXS port type e1Framer, e1Slave, t1Framer, t1Slave - are applicable for the mvc4Pbx cards only. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), eAndM4wires(2), eAndM2wires(3), fxoGnd(4), fxoLoop(5), fxsGnd(6), fxsLoop(7), e1Framer(8), e1Slave(9), t1Framer(10), t1Slave(11) | ||
| prtExPVc4TxGain | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.7 | ||
| Transmission gain in dBm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4RxGain | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.8 | ||
| Reception gain in dBm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4MaxRate | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.9 | ||
| Voice rate. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), r4800bps(2), r7200bps(3), r9600bps(4), notApplicatble(255) | ||
| prtExPVc4Tc | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.10 | ||
| Time interval for CIR control, in seconds. The value will be the same for all cards' ports. | |||
| OBJECT-TYPE | |||
| INTEGER | t1sec(1), t2sec(2), t3sec(3), t4sec(4) | ||
| prtExPVc4Oos | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.11 | ||
| Handling type, when connection is lost. | |||
| OBJECT-TYPE | |||
| INTEGER | notSupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6) | ||
| prtExPVc4EchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.12 | ||
| Echo canceler activation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtExPVc4VarDelay | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.13 | ||
| Maximum variant delay of the FR network, in msec. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..300 | ||
| prtExPVc4CongLevel | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.14 | ||
| This object indicates the level of delayed data in precents of total available dynamic memory, for which the port will start to operate as congested. The resolution of the parameter is 5%. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..70 | ||
| prtExPVc4Wire | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.15 | ||
| This object indicates the wiring of the E&M port. It is applicable only for E&M card type. | |||
| OBJECT-TYPE | |||
| INTEGER | w2wire(1), w4wire(2), notApplicable(255) | ||
| prtExPVc4ExtensionType | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.16 | ||
| This object indicates the type of extension relevant for this port. ipForceConnect (6) is used for automatic connection or automatic dialing when the phone is off hook (hot line). permanentDial (7) means that the call is established upon power up. The hook may be on or off. Permanent Dialing can be used when there is no signaling. autoAccept (8) means that the called party in the Permanent Dialing will accept the call from the remote side automatically upon on or off hook. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), forceConnect(2), voiceSwitching(3), transparent(4), transparentPlus(5), ipForceConnect(6), permanentDial(7), autoAccept(8) | ||
| prtExPVc4ExtensionNumber | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.17 | ||
| This is the extension number of this port. This field is relevant only when the extension type is voice switching and is read only if the port is member of a hunt group. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(2) | ||
| prtExPVc4OutPulsing | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.18 | ||
| This field indicates whether to outpulse the received digits. It is notApplicable(1) when the extension type is forceConnect(2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPVc4HuntGroupMb | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.19 | ||
| This object indicates if this port belongs to an hunt group. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPVc4HuntGroupIdx | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.20 | ||
| If it belongs to an hunt group, this fields indicates the index of the relevant hunt group. 0 = notApplicable | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| prtExPVc4AutoFaxMode | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.21 | ||
| This object indicates if the system will switch automatically to FAX mode when detecting FAX activity. Default=Yes. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPVc4FaxRate | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.22 | ||
| FAX initial rate. Default=9600 bps. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), r4800bps(2), r7200bps(3), r9600bps(4), r12000bps(5), r14400bps(6), r2400bps(7) | ||
| prtExPVc4SeizeAck | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.23 | ||
| This parameter shows whether the device will acknowledge a seize signal (On/Off Hook). When the value is set to yes(3) & the device receives an on/off hook signal it will transmit back an on/off hook signal. When the value is set to no(2) & the device receives an on/off hook signal it will NOT transmit back an on/off hook signal. Example: If Seize Ack Parameter = YES, when the MVC.4 receives a seize signal (Off Hook) from the PBX it will send an Off Hook to the PBX. The Seize Parameter is relevant for all the following cards: MVC-4 MVC-4/E1-Framer MVC-4/T1-DSU-Framer MVC-4/T1-CSU-Framer MVC-4/E1-SLAVE MVC-4/T1-SLAVE Default values: Analog FXS - No (value can't be changed). Analog FXO - Yes (value can't be changed). Analog E&M - No (values NO/YES). Digital E1/T1 Framer & Slave - No. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPVc4SignalingProtocol | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.24 | ||
| The signaling protocol that will be used between the PABX & the voice port. Delay Start Protocol: the line is seized by sending an Off hook signal and after a delay, if the called party is available (On hook) DTMF (Dual Tone Multi Frequency) digits are sent towards the called party. Immediate Start Protocol: the line is seized by sending an Off Hook signal and immediately DTMF digits are sent towards the called party. Wink start protocol: the line is seized by sending an Off Hook signal and then the called party sends a short Off Hook wink signal. Now the calling party starts sending DTMF digits. | |||
| OBJECT-TYPE | |||
| INTEGER | delayStart(2), immediateStart(3), winkStart(4) | ||
| prtExPVc4DelayStart | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.25 | ||
| This parameter is used only for Delay Protocol. This is the time that the calling party will wait after sending an Off hook signal and before sending DTMF digits to the called party. The delay values are 100..5000 msec in intervals of 100 msec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4WinkMinDuration | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.26 | ||
| This parameter is used only for Wink Protocol. Min Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4WinkMaxDuration | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.27 | ||
| This parameter is used only for Wink Protocol. Max Duration of the Wink Signal (off hook duration from the called party). Legal values: 40..400 msec in intervals of 10 msec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4GenerateTone | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.28 | ||
| This parameter indicates whether the device (MX or MPH) should generate dial tones for the channel. If the value is yes (3), it generates dial tones. If the value is no (2), the connected equipment will generate dial tones. For example for some ISDN sets the dial tone is generated by the phone itself while for others sets it is generated by the MX. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPVc4CodingLaw | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.29 | ||
| This attribute indicates the Method/Law for decoding/encoding the voice information. aLaw(1) is the standard Law for E1 links. uLaw(2) is the standard Law for T1 links. This object is equal for all the ports in the specific module because of HW limitations | |||
| OBJECT-TYPE | |||
| INTEGER | aLAW(1), uLAW(2) | ||
| prtExPVc4GenerateRingBack | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.30 | ||
| Determines whether the Ring Back tone is generated locally or from the remote end. The default is - NO (Meaning coming from the remote end). Yes means that the Ring Back Tone is generated locally. Applicable only for Force Connect. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtExPVc4ChannelId | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.31 | ||
| Channel Identifier. According to FRF11 each voice port that works as force connect should add a CH Id after the DLCI in the frame header. Default : 1 Applicable only for Force Connect. Not Applicable value will be 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..256 | ||
| prtExPVc4PortConnection | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.32 | ||
| Port connection determines whether the port is connected to a PABX (Trunk) or to Telephone set (Line) . It determines whether to send certain messages to the port or not. If the type is LINE then the port generates a ring back tone , if TRUNK it doesn't (The PBX does it). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), line(2), trunk(3) | ||
| prtExPVc4CoderAndRate | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.33 | ||
| Coder and Rate for the Voice Compression. Relevant for MVC-8 card only. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), g7231r6300BPS(2), g7231r5300BPS(3), g729A8KBPS(4), g711aLAW(5), g711uLAW(6), g726r16KBPS(7), g726r24KBPS(8), g726r32KBPS(9), g726r40KBPS(10), g727r16KBPS(11), g727r24r16KBPS(12), g727r24KBPS(13), g727r16r32KBPS(14), g727r32r24KBPS(15), g727r32KBPS(16), g727r40r16KBPS(17), g727r40r24KBPS(18), g727r40r32KBPS(19), transparent(20), netcoder6400BPS(21), netcoder7200BPS(22), netcoder8KBPS(23), netcoder8800BPS(24), netcoder9600BPS(25) | ||
| prtExPVc4DestinationNum | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.34 | ||
| The destination phone number: 0 to 22 digits. Applicable for Auto Dial - ipForceConnect(6), Permanent Dial and Auto Accept Extension Types. Default: Null String | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| prtExPVc4DtmfRelay | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.35 | ||
| When DTMF RELAY is disabled, the DTMF digits (dialed by the user) are transmitted as compressed voice and in the remote unit are decompressed. When DTMF RELAY is enabled, the DTMF digits are detected at the near side and not transmitted as voice. Instead, only an indication of what digits were dialed are transmitted and in the far end the tone is regenerated. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| prtExPVc4DiscOnSilence | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.36 | ||
| No. of silenced seconds after which the call will be disconected. A value of 0 means that there will be no disconnect when there is silence. Possible values: 0 - 900 sec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExPVc4DynamicJitter | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.37 | ||
| The MVC8 uses two mechanisms to overcome the network delay. The first one is a static jitter buffer which holds a constant buffer of up to 300 Msec and can be controled by the JITTER parameter (prtExPVc4VarDelay). The second one is the dynamic jitter which calculates, in real time, the network delay and handles a jitter buffer dynamically. The dynamic mechanism that is implemented in MVC8, was intended to overcome network delay yet when the network bursts, the MVC8 dynamic mechanism is not able to overcome the delay. Therefore it is better not to use the dynamic jitter (DISABLE - should be the default) where bursts may occur often. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| prtExPVc4EandMType | 1.3.6.1.4.1.164.3.2.3.2.9.1.1.38 | ||
| This is the signaling type on the E&M analog side. The analog signaling includes voltage, no. of pins and other parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), type1(2), type2(3), type3(4), ssdc5(5) | ||
| prtExPVc4DlciTable | 1.3.6.1.4.1.164.3.2.3.2.9.2 | ||
| The write operation into the Table Objects is valid only at the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExPVc4DlciEntry | |||
| prtExPVc4DlciEntry | 1.3.6.1.4.1.164.3.2.3.2.9.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExPVc4DlciEntry | |||
| prtExPVc4DlciCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExPVc4DlciSltIdx | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPVc4DlciPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.3 | ||
| This attribute indicates a unique internal port number. VC4 cards have four external ports. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4) | ||
| prtExPVc4DlciValid | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.4 | ||
| This attribute indicates whether the attributes in this entry are valid or not. The user can add/delete pvc (dlci to dlci connection) by modifing this object | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExPVc4DlciIConSlt | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.5 | ||
| This attribute indicates a unique slot position In the Mux (Agent) where the dlci is routed to. In the ?004 Unit the entries io6(10)..io16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExPVc4DlciIConPrt | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.6 | ||
| This attribute indicates a unique port id which the dlci is routed to. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106), inPrt7(107), inPrt8(108), inPrt9(109), inPrt10(110), inPrt11(111), inPrt12(112) | ||
| prtExPVc4DlciIConDlci | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.7 | ||
| This attribute indicates a unique internal connection dlci number, the dlci is routed to. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..991 | ||
| prtExPVc4DlciTxBc | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.8 | ||
| This attribute indicates a unique Tx committed bandwidth on the user transmit line (or at the port receive line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBc9600bps(3), txBc14400bps(4), txBc19200bps(5), txBc28800bps(6), txBc32000bps(7), txBc38400bps(8), txBc48000bps(9), txBc56000bps(10), txBc57600bps(11), txBc64Kbps(12), txBc128Kbps(13), txBc192Kbps(14), txBc256Kbps(15), txBc320Kbps(16), txBc384Kbps(17), txBc448Kbps(18), txBc512Kbps(19), txBc768Kbps(20), txBc1024Kbps(21), txBc16000bps(25), txBc112Kbps(26) | ||
| prtExPVc4DlciTxBe | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.9 | ||
| This attribute indicates a unique Tx excess bandwidth on the user transmit line (or at the port receive line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), txBe9600bps(3), txBe14400bps(4), txBe19200bps(5), txBe28800bps(6), txBe32000bps(7), txBe38400bps(8), txBe48000bps(9), txBe56000bps(10), txBe57600bps(11), txBe64Kbps(12), txBe128Kbps(13), txBe192Kbps(14), txBe256Kbps(15), txBe320Kbps(16), txBe384Kbps(17), txBe448Kbps(18), txBe512Kbps(19), txBe768Kbps(20), txBe1024Kbps(21), txBc16000bps(25), txBc112Kbps(26) | ||
| prtExPVc4DlciRxBc | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.10 | ||
| This attribute indicates a unique Rx committed bandwidth on the user receive line (or at the port transmit line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBc9600bps(3), rxBc14400bps(4), rxBc19200bps(5), rxBc28800bps(6), rxBc32000bps(7), rxBc38400bps(8), rxBc48000bps(9), rxBc56000bps(10), rxBc57600bps(11), rxBc64Kbps(12), rxBc128Kbps(13), rxBc192Kbps(14), rxBc256Kbps(15), rxBc320Kbps(16), rxBc384Kbps(17), rxBc448Kbps(18), rxBc512Kbps(19), rxBc768Kbps(20), rxBc1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26) | ||
| prtExPVc4DlciRxBe | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.11 | ||
| This attribute indicates a unique Rx excess bandwidth on the user receive line (or at the port transmit line). | |||
| OBJECT-TYPE | |||
| INTEGER | full(1), zero(2), rxBe9600bps(3), rxBe14400bps(4), rxBe19200bps(5), rxBe28800bps(6), rxBe32000bps(7), rxBe38400bps(8), rxBe48000bps(9), rxBe56000bps(10), rxBe57600bps(11), rxBe64Kbps(12), rxBe128Kbps(13), rxBe192Kbps(14), rxBe256Kbps(15), rxBe320Kbps(16), rxBe384Kbps(17), rxBe448Kbps(18), rxBe512Kbps(19), rxBe768Kbps(20), rxBe1024Kbps(21), rxBc16000bps(25), rxBc112Kbps(26) | ||
| prtExPVc4DlciPriority | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.12 | ||
| This attribute indicates a unique priority of the pvc. 6 is the lowest priority and 8 is the highest priority. | |||
| OBJECT-TYPE | |||
| Integer32 | 6..8 | ||
| prtExPVc4DlciStatus | 1.3.6.1.4.1.164.3.2.3.2.9.2.1.13 | ||
| This attribute indicates the status of the pvc. The status is disconnected(1) when one of the sides is programmed as not connected | |||
| OBJECT-TYPE | |||
| INTEGER | disconnected(1), connected(2) | ||
| prtHsrCnfg | 1.3.6.1.4.1.164.3.2.3.2.10 | ||
| OBJECT IDENTIFIER | |||
| prtExHsrCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.10.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExHsrCnfgEntry | |||
| prtExHsrCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.10.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExHsrCnfgEntry | |||
| prtExHsrCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.1 | ||
| This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExHsrSltIdx | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.2 | ||
| This object indicates a unique slot position where the card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19) | ||
| prtExHsrPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.3 | ||
| A unique prt identifier within the card. Valid values: For MP: - For HS-R cards: exPrt1 (1) .. exPrt4 (4) - For HS-U/1 cards: inPrt1 (101) .. inPrt4 (104) - For HS-S12, HS-S6, HS-U12, HS-U6 cards: exPrt1 (1) .. exPrt12 (12). This MIB table is used only for LT-1 interface. For DXC: - For HS-U8, HS-U16 cards: 111 .. 2531 (See DXC R6 spec for port index convention). This MIB table is used only for LT-1 interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExHsrConnect | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.4 | ||
| This object indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExHsrProtocol | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.5 | ||
| This object indicates the protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(2), async(3) | ||
| prtExHsrRate | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.6 | ||
| This object indicates the port speed. The 16,32,48,56,64 and 128 kbps rates are applicable only for Sync protocol. The 57.6 and 115.2 kbps rates are applicable only for Async protocol. notConnected= 0 rate. | |||
| OBJECT-TYPE | |||
| INTEGER | r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r19200bps(7), r38400bps(8), r48kbps(9), r56kbps(10), r64kbps(11), r16000bps(12), r32000bps(13), r57600bps(14), r115200bps(15), r128000bps(16), notConnected(100) | ||
| prtExHsrDataBits | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.7 | ||
| Data Bits. This object is applicable for Async protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | d5bits(1), d6bits(2), d7bits(3), d8bits(4), notApplicable(255) | ||
| prtExHsrParity | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.8 | ||
| - For HS-R card, this object indicates if the parity bit is needed or not. Therefore, the 'no' and 'yes; values are applicable. - For HS-S12, HS-U12, the parity type is selected: no, odd, even. This object is applicable for Async protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3), odd(4), even(5), notApplicable(255) | ||
| prtExHsrStopBits | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.9 | ||
| This object indicates the minimum number of stop bits in the tx async frame. This object is applicable for Async protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | stopBits1Bit(1), stopBits2Bits(2), notApplicable(255) | ||
| prtExHsrCts | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.10 | ||
| CTS. This object is applicable for Async protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), rts(3), notApplicable(255) | ||
| prtExHsrClkMode | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.11 | ||
| Clock mode. This object is applicable for Sync protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), extDce(2), notApplicable(255) | ||
| prtExHsrLinkTo | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.12 | ||
| It indicates the slot of the main link card to which the HS-R card is mapped. notApplicable - for HS-U/1 internal ports. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExHsrDcdDsr | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.13 | ||
| DCD & DSR. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), endToEnd(3) | ||
| prtExHsrOperMode | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.14 | ||
| This object indicates the operation mode of the port. normal = bi-directional (Tx/Rx) unidirectRx = unidirectional Rx. broadcast = Tx upon request. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(2), unidirectRx(3), broadcast(4) | ||
| prtExHsrRtsDtr | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.15 | ||
| RTS & DTR. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), endToEnd(3) | ||
| prtExHsrLlbEnable | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.16 | ||
| Enable/Disable LLB. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtExHsrRlbEnable | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.17 | ||
| Enable/Disable RLB. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtExHsrRateAdapt | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.18 | ||
| Rate Adaptation - takes a low rate and adapts it to 64Kbps. This object specifies the means this adaptation is done by. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), proprietary(2), v110(3) | ||
| prtExHsrRemoteModem | 1.3.6.1.4.1.164.3.2.3.2.10.1.1.19 | ||
| Remote modem. asmi31s2 = ASMi-31/2 | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), asmi31(2), asmi31s2(3) | ||
| prtMbeCnfg | 1.3.6.1.4.1.164.3.2.3.2.11 | ||
| OBJECT IDENTIFIER | |||
| prtExMbeCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.11.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExMbeCnfgEntry | |||
| prtExMbeCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.11.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExMbeCnfgEntry | |||
| prtExMbeCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.11.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExMbeSltIdx | 1.3.6.1.4.1.164.3.2.3.2.11.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExMbePrtIdx | 1.3.6.1.4.1.164.3.2.3.2.11.1.1.3 | ||
| A unique port identifier within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExMbeLan | 1.3.6.1.4.1.164.3.2.3.2.11.1.1.4 | ||
| This attribute indicates whether the MBE port is operated as main or remote bridge. | |||
| OBJECT-TYPE | |||
| INTEGER | remote(1), main(2) | ||
| prtInMbeCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.11.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInMbeCnfgEntry | |||
| prtInMbeCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.11.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInMbeCnfgEntry | |||
| prtInMbeCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInMbeSltIdx | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInMbePrtIdx | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.3 | ||
| A unique port identifier within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101) | ||
| prtInMbeConnect | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInMbeRate | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r1x64eq64Kbps(1), r2x64eq128Kbps(2), r3x64eq192Kbps(3), r4x64eq256Kbps(4), r5x64eq320Kbps(5), r6x64eq384Kbps(6), r7x64eq448Kbps(7), r8x64eq512Kbps(8), r9x64eq576Kbps(9), r10x64eq640Kbps(10), r11x64eq704Kbps(11), r12x64eq768Kbps(12), r13x64eq832Kbps(13), r14x64eq896Kbps(14), r15x64eq960Kbps(15), r16x64eq1024Kbps(16), r17x64eq1088Kbps(17), r18x64eq1152Kbps(18), r19x64eq1216Kbps(19), r20x64eq1280Kbps(20), r21x64eq1344Kbps(21), r22x64eq1408Kbps(22), r23x64eq1472Kbps(23), r24x64eq1536Kbps(24) | ||
| prtInMbeLinkTo | 1.3.6.1.4.1.164.3.2.3.2.11.2.1.6 | ||
| It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtTreCnfg | 1.3.6.1.4.1.164.3.2.3.2.12 | ||
| OBJECT IDENTIFIER | |||
| prtExTreCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.12.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExTreCnfgEntry | |||
| prtExTreCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.12.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExTreCnfgEntry | |||
| prtExTreCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.12.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExTreSltIdx | 1.3.6.1.4.1.164.3.2.3.2.12.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExTrePrtIdx | 1.3.6.1.4.1.164.3.2.3.2.12.1.1.3 | ||
| A unique port identifier within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExTreLan | 1.3.6.1.4.1.164.3.2.3.2.12.1.1.4 | ||
| This attribute indicates whether the TRE port is operated as main or remote bridge. Default=remote. | |||
| OBJECT-TYPE | |||
| INTEGER | remote(1), main(2) | ||
| prtExTreLanRate | 1.3.6.1.4.1.164.3.2.3.2.12.1.1.5 | ||
| This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M. | |||
| OBJECT-TYPE | |||
| INTEGER | r4M(1), r16M(2) | ||
| prtInTreCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.12.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInTreCnfgEntry | |||
| prtInTreCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.12.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInTreCnfgEntry | |||
| prtInTreCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInTreSltIdx | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInTrePrtIdx | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.3 | ||
| A unique port identifier within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101) | ||
| prtInTreConnect | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInTreRate | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.5 | ||
| This attribute indicates the port speed. | |||
| OBJECT-TYPE | |||
| INTEGER | r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17) | ||
| prtInTreLinkTo | 1.3.6.1.4.1.164.3.2.3.2.12.2.1.6 | ||
| It indicates the slot of the main link card to which the MBE card is mapped. In the ?004 Unit the entries io6(10)..io16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtLs6Cnfg | 1.3.6.1.4.1.164.3.2.3.2.13 | ||
| OBJECT IDENTIFIER | |||
| prtExLs6CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.13.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExLs6CnfgEntry | |||
| prtExLs6CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.13.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExLs6CnfgEntry | |||
| prtExLs6CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExLs6SltIdx | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExLs6PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.3 | ||
| This attribute indicates a unique port index. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12) | ||
| prtExLs6Connect | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExLs6Protocol | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.5 | ||
| This attribute indicates the protocol. async - can be selected only for ports 1-2. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(2), async(3) | ||
| prtExLs6Rate | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.6 | ||
| Port rates in bps. g1 - contains the values : (2)-(6),(9),(12),(16) g2 - contains the values : (7),(10),(14),(19) g3 - contains the values : (8),(11),(13),(15),(17),(18),(20); it is not applicable when using Async protocol. Rates of pair ports (1-2, 3-4, 5-6) must be from the same group. | |||
| OBJECT-TYPE | |||
| INTEGER | r300bps(2), r600bps(3), r1200bps(4), r2400bps(5), r4800bps(6), r7200bps(7), r8000bps(8), r9600bps(9), r14400bps(10), r16000bps(11), r19200bps(12), r24000bps(13), r28800bps(14), r32000bps(15), r38400bps(16), r48000bps(17), r56000bps(18), r57600bps(19), r64000bps(20) | ||
| prtExLs6ClkMode | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.7 | ||
| This attribute indicates a unique port operation clock mode. It is applicable for Sync protocol only . | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), extDce(2), dte1(3), notApplicable(255) | ||
| prtExLs6CtrlSignal | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.8 | ||
| Control Signal. | |||
| OBJECT-TYPE | |||
| INTEGER | local(2), rts(3), dtrAndRts(4) | ||
| prtExLs6DataBits | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.9 | ||
| Data Bits. This object is applicable for Async protocol only. | |||
| OBJECT-TYPE | |||
| INTEGER | d6bits(1), d7bits(2), d8bits(3), d9bits(4), notApplicable(255) | ||
| prtExLs6Cts | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.10 | ||
| This object indicates the CTS control line operation mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), rts(3) | ||
| prtExLs6LinkToInternal | 1.3.6.1.4.1.164.3.2.3.2.13.1.1.11 | ||
| This object indicates which internal port of the card, the external port is linked to. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101), inPrt2(102), notApplicable(255) | ||
| prtExLs6VCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.13.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExLs6VCnfgEntry | |||
| prtExLs6VCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.13.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExLs6VCnfgEntry | |||
| prtExLs6VCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExLs6VSltIdx | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExLs6VPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt7(7), exPrt8(8) | ||
| prtExLs6VConnect | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExLs6VRate | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.5 | ||
| Rate (bps) used for FAX transmission and Voice coding. | |||
| OBJECT-TYPE | |||
| INTEGER | r6400bps(2), r7200bps(3), r8000bps(4), r9600bps(5), r16000bps(6), r24000bps(7), r32000bps(8), r64000bps(9) | ||
| prtExLs6VEchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.6 | ||
| Echo canceler activation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtExLs6VIfType | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.7 | ||
| This attribute indicates the interface type of the port. w4wire - is applicable only for E&M port type. | |||
| OBJECT-TYPE | |||
| INTEGER | w2wire(1), w4wire(2) | ||
| prtExLs6VTxGain | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.8 | ||
| Transmit gain in dBm. E&M - values range: -17 .. 8 FXO - values range: -16 .. 4 FXS - values range: -13 .. 8 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExLs6VRxGain | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.9 | ||
| Receive gain in dBm. E&M - values range: -17 .. 2 FXO - values range: -17 .. -1 FXS - values range: -17 .. 2 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExLs6VOos | 1.3.6.1.4.1.164.3.2.3.2.13.2.1.10 | ||
| Out of Service signaling mode. | |||
| OBJECT-TYPE | |||
| INTEGER | forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4) | ||
| prtInLs6CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.13.3 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInLs6CnfgEntry | |||
| prtInLs6CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.13.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInLs6CnfgEntry | |||
| prtInLs6CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInLs6SltIdx | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInLs6PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.3 | ||
| This attribute indicates a unique internal port index. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101), inPrt2(102) | ||
| prtInLs6Connect | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. It also affects all the module considerations because the module has only one Internal interface which is the composite channel. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInLs6TandemMode | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.5 | ||
| This object indicates the Tandem Mode. tandemSlave - is valid only for an LS-6 card having on the (current slot-1) an LS-6 card with 'tandemMaster' mode. | |||
| OBJECT-TYPE | |||
| INTEGER | noTandem(1), tandemMaster(2), tandemSlave(3) | ||
| prtInLs6Rate | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.6 | ||
| Main Rate in Kbps. | |||
| OBJECT-TYPE | |||
| INTEGER | r32Kbps(1), r56Kbps(2), r64Kpbs(3), r128Kbps(4), r256Kbps(5), r384Kbps(6), r192Kbps(7), r512Kbps(8), r768Kbps(9), r14400bps(10) | ||
| prtInLs6RemoteType | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.7 | ||
| Remote Type. notApplicable - when prtInLs6TandemMode=tandemSlave | |||
| OBJECT-TYPE | |||
| INTEGER | ls6(1), km2kSlave(2), km2kStandalone(3), notApplicable(255) | ||
| prtInLs6LinkTo | 1.3.6.1.4.1.164.3.2.3.2.13.3.1.8 | ||
| It indicates the slot of the main link card to which the Ls6 card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. notApplicable - when prtInLs6TandemMode=tandemSlave. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtVc3Cnfg | 1.3.6.1.4.1.164.3.2.3.2.14 | ||
| OBJECT IDENTIFIER | |||
| prtExVc3CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.14.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExVc3CnfgEntry | |||
| prtExVc3CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.14.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExVc3CnfgEntry | |||
| prtExVc3CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExVc3SltIdx | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExVc3PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3) | ||
| prtExVc3Connect | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExVc3TransGain | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.5 | ||
| Transmit gain in dBm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVc3ReceiveGain | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.6 | ||
| Receive gain in dBm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVc3Wire | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.7 | ||
| This object is equal for all the ports in the specific card because of HW limitations | |||
| OBJECT-TYPE | |||
| INTEGER | w2wire(1), w4wire(2) | ||
| prtExVc3Rate | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.8 | ||
| Rate in bps. | |||
| OBJECT-TYPE | |||
| INTEGER | r9600bps(1), r4800bps(2) | ||
| prtExVc3EchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.14.1.1.9 | ||
| Echo canceler activation. The value will be the same for all the card's external ports. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtInVc3CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.14.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtInVc3CnfgEntry | |||
| prtInVc3CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.14.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtInVc3CnfgEntry | |||
| prtInVc3CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtInVc3SltIdx | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtInVc3PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101) | ||
| prtInVc3Connect | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtInVc3Rate | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.5 | ||
| Rate in bps. | |||
| OBJECT-TYPE | |||
| INTEGER | r32000bps(1), r16000bps(2) | ||
| prtInVc3Oos | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.6 | ||
| This object is equal for all the ports in the specific card because of HW limitations | |||
| OBJECT-TYPE | |||
| INTEGER | forcedIdle(1), forcedBusy(2), busyIdle(3), idleBusy(4) | ||
| prtInVc3LinkTo | 1.3.6.1.4.1.164.3.2.3.2.14.2.1.7 | ||
| This attribute indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtVcPbxCnfg | 1.3.6.1.4.1.164.3.2.3.2.15 | ||
| OBJECT IDENTIFIER | |||
| prtExVcPbxCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.15.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExVcPbxCnfgEntry | |||
| prtExVcPbxCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.15.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExVcPbxCnfgEntry | |||
| prtExVcPbxCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.1 | ||
| This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExVcPbxSltIdx | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.2 | ||
| This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExVcPbxPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExVcPbxConnect | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.4 | ||
| This object indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtExVcPbxGroup | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.5 | ||
| The group object links together several VC-PBX cards, concerning compression of the same input T1/E1 link time-slots. When ports of different slots have the same group, they are linked. When ports have a different group, they are not linked. For VC-PBX/T1 and E1 cards, this object is - their own IO Slot. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExVcPbxTransparent | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.6 | ||
| This object indicates whether the Transparent transfer of Time-Slots is required or not. Time-Slots transferred by Transparent, will not be compressed. no - applicable only for VC-PBX/T1 and VC-PBX/E1 cards yes - applicable only for VC-PBX/T1 and VC-PBX/E1 cards notApplicable - only for VC-PBX cards. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3), notApplicable(255) | ||
| prtExVcPbxTransSignalTs | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.7 | ||
| This object specifies the ML Time-Slot dedicated to the signaling of the PABX Transparent TSs. None = 255. When prtExVcPbxTransparent=no this object's value=None (255) When prtExVcPbxTransparent=notApplicable, this object's value=None (255). When prtExVcPbxTransparent=yes: - for VC-PBX/T1 ports, this object's valid values are 1..16 or None (255). - for VC-PBX/E1 ports, this object's value will be 16 or None (255). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVcPbxFrame | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.8 | ||
| This object is the frame parameter for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 values for the VC-PBX/T1 card. E1 values for the VC-PBX/E1 card. notApplicable - for the VC-PBX card. This parameter has the same values as dsx1LineType in T1/E1 MIB (RFC-1406). The parameters in dsx1LineType are: other (1) esfT1 dsx1ESF (2) sfT1 dsx1D4 (3) g732nE1 dsx1E1 (4) g732nE1CRC dsx1E1-CRC (5) g732sE1 dsx1E1-MF (6) g732sE1CRC dsx1E1-MF-CRC (7) | |||
| OBJECT-TYPE | |||
| INTEGER | esfT1(2), sfT1(3), g732nE1(4), g732nE1CRC(5), g732sE1(6), g732sE1CRC(7), notApplicable(255) | ||
| prtExVcPbxRestoreTime | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.9 | ||
| The time passing from the disappearance of the loss of synchronization condition (red alarm) to the restoration of normal service. The options 1secFast(2) and 10sec62411(3) for E1 interfaces are proprietary implementation of the T1 standard to the E1 interface. ccittE1 - is applicable only for VC-PBX/E1 card notApplicable - is applicable for VC-PBX card | |||
| OBJECT-TYPE | |||
| INTEGER | restoreT1secFast(2), restoreT10sec62411(3), ccittE1(4), notApplicable(255) | ||
| prtExVcPbxLineCode | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.10 | ||
| This object is the line code parameter used for T1/E1 interface. The user should select only the parameters which are relevant to the specific card: T1 line code parameters for VC-PBX/T1 E1 line code parameters for VC-PBX/E1 notApplicable - for VC-PBX This parameter has the same values as dsx1LineCoding in T1/E1 MIB (RFC-1406). The parameters in dsx1LineCoding are: dsx1JBZS (1) dsx1B8ZS (2) dsx1HDB3 (3) dsx1ZBTSI (4) dsx1AMI (5) other (6) | |||
| OBJECT-TYPE | |||
| INTEGER | b7zsT1(1), b8zsT1(2), transT1(3), hdb3E1(4), notApplicable(255) | ||
| prtExVcPbxLineLength | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.11 | ||
| This object is the line length parameter. It is applicable only for the VC-PBX/T1 card. notApplicable - for the VC-PBX and VC-PBX/E1 card. lenXXXpXXXft = len-XXX-XXXft. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), notApplicable(255) | ||
| prtExVcPbxLinkTo | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.12 | ||
| This object indicates the slot of the ML card to which the VC-PBX/T1, VC-PBX/E1 card Transparent TSs are mapped. notApplicable - for VC-PBX card AND for VC-PBX/T1, VC-PBX/E1 cards, when prtExVcPbxTransparent=no . In the ?004 Unit the entries io6(10)..io12(16) are not valid. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExVcPbxSignalOper | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.13 | ||
| This object indicates the Signaling Operation of the VC-PBX/T1, VC-PBX/E1 external port. notApplicable - for VC-PBX card normal - all 4 signaling bits are transferred. bEqA - copy the A bit into the B bit. Applicable only for VC-PBX/T1. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), normal(2), bEqA(3), inverseA(4) | ||
| prtExVcPbxIdleCode | 1.3.6.1.4.1.164.3.2.3.2.15.1.1.14 | ||
| Determines the code for transmission in empty time slots. notApplicable - for VC-PBX card . | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), hff(2), he4(3), hd5(4), h9e(5), h98(6), h7f(7), h7e(8), h54(9), h1a(10) | ||
| prtIn1p6VcPbxCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.15.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIn1p6VcPbxCnfgEntry | |||
| prtIn1p6VcPbxCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.15.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIn1p6VcPbxCnfgEntry | |||
| prtIn1p6VcPbxCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.1 | ||
| This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIn1p6VcPbxSltIdx | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.2 | ||
| This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtIn1p6VcPbxPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106) | ||
| prtIn1p6VcPbxConnect | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.4 | ||
| This object indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtIn1p6VcPbxRate | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.5 | ||
| This object indicates the port Rate. For Normal mode (prtIn7p8VcPbxMode=normal), only part of the values are valid (constant rate). For Server mode (prtIn7p8VcPbxMode=server), all values are applicable (user can select the desired compression rate). | |||
| OBJECT-TYPE | |||
| INTEGER | r4800bps(1), r6400bps(2), r7200bps(3), r8000bps(4), r9600bps(5), r12800bps(6) | ||
| prtIn1p6VcPbxEchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.6 | ||
| Echo canceler activation. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtIn1p6VcPbxPabxTs | 1.3.6.1.4.1.164.3.2.3.2.15.2.1.7 | ||
| This object defines the PABX Time-Slot assigned to this internal port. For a T1 link, the valid values are: 1 .. 24. For an E1 link, the valid values are: 1 .. 31. This object is NOT applicable when prtIn1p6VcPbxConnect=no. This object is applicable for all cards of VC-PBX family. Default=the internal port index (1..6). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..31 | ||
| prtIn7p8VcPbxCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.15.3 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIn7p8VcPbxCnfgEntry | |||
| prtIn7p8VcPbxCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.15.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIn7p8VcPbxCnfgEntry | |||
| prtIn7p8VcPbxCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.1 | ||
| This object indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIn7p8VcPbxSltIdx | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.2 | ||
| This object indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtIn7p8VcPbxPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.3 | ||
| A unique identifier of the port, within the card. | |||
| OBJECT-TYPE | |||
| INTEGER | inPrt7(107), inPrt8(108) | ||
| prtIn7p8VcPbxConnect | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.4 | ||
| This object indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtIn7p8VcPbxMode | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.5 | ||
| This object indicates the working mode of the port: - normal - the compressed voice will be sent to an MTML card inside the Mux. - server - the compressed voice will be sent to the Digital Voice connector, as a service to an outside user. | |||
| OBJECT-TYPE | |||
| INTEGER | normal(1), server(2) | ||
| prtIn7p8VcPbxRate | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.6 | ||
| This object indicates the port Main Rate. For Server mode (prtIn7p8VcPbxMode=server), the value will be notApplicable. | |||
| OBJECT-TYPE | |||
| INTEGER | r32Kbps(1), r16Kbps(2), notApplicable(255) | ||
| prtIn7p8VcPbxSignalMode | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.7 | ||
| This object indicates the Signal Mode. For Server mode (prtIn7p8VcPbxMode=server), the only valid values are: - none - aBit | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), aBit(2), abcBit(3), abcdBit(4) | ||
| prtIn7p8VcPbxOos | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.8 | ||
| Out of service Signaling mode. | |||
| OBJECT-TYPE | |||
| INTEGER | forcedIdle(1), forcedBusy(2) | ||
| prtIn7p8VcPbxLinkTo | 1.3.6.1.4.1.164.3.2.3.2.15.3.1.9 | ||
| This object indicates the slot of the ML card to which the VC card is mapped. In the ?004 Unit the entries io6(10)..io12(16) are not valid. For Server mode (prtIn7p8VcPbxMode=server), this object is not applicable. Both ports, 7 and 8 should be linked to the same Slot. STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot and prtGenCnfgLinkToPort. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtExVcPbxTsTable | 1.3.6.1.4.1.164.3.2.3.2.15.4 | ||
| The write operation into the table objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtExVcPbxTsEntry | |||
| prtExVcPbxTsEntry | 1.3.6.1.4.1.164.3.2.3.2.15.4.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtExVcPbxTsEntry | |||
| prtExVcPbxTsCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtExVcPbxTsSltIdx | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExVcPbxTsPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.3 | ||
| This attribute indicates a unique port number. VCPBX/E1 and VCPBX/T1 cards have only one external interface. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1) | ||
| prtExVcPbxTsIdx | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.4 | ||
| This attribute indicates a unique PABX time slot position. The valid time slots are 1..24 for VC-PBX/T1 and 1..31 for VC-PBX/E1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtExVcPbxTsMode | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.5 | ||
| This attribute indicates the usage, process and way of the specific PABX TS towards its destination: unused - the TS is not used (no processing, no destination). compressed - the TS is used, sent for compression to an internal port 1..6 of either the same card or a VC-PBX card of the same group. transparent - the TS is used, no processing, it is sent directly to the ML card the VC-PBX/T1,(E1) is linked to. | |||
| OBJECT-TYPE | |||
| INTEGER | unused(1), compressed(2), transparent(3) | ||
| prtExVcPbxTsIConSlot | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.6 | ||
| The object's io1..io12 values are applicable only when prtExVcPbxTsMode=compressed. Otherwise, its value should be noConnect. This object indicates whether the specified compressed time slot is connected/routed internally in the Agent and to which card it is connected. The valid selectable slots are either the current one, (prtExVcPbxTsSltIdx), or a slot containing a VC-PBX card. In the ?004 Unit the entries io6(10)..io12(16) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtExVcPbxTsIConPrt | 1.3.6.1.4.1.164.3.2.3.2.15.4.1.7 | ||
| This attribute indicates the internal VC-PBX port to which this PABX TS is connected for compression. noConnect - when prtExVcPbxTsIConSlot=noConnect. | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(100), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104), inPrt5(105), inPrt6(106) | ||
| prtIsdnCnfg | 1.3.6.1.4.1.164.3.2.3.2.16 | ||
| OBJECT IDENTIFIER | |||
| prtIsdnCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.16.1 | ||
| The write operation into the table objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIsdnCnfgEntry | |||
| prtIsdnCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.16.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIsdnCnfgEntry | |||
| prtIsdnCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIsdnSltIdx | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In the ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB' | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255) | ||
| prtIsdnPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.3 | ||
| This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnConnect | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.4 | ||
| This attribute indicates if the port is connected. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtIsdnSignalingProtocol | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.5 | ||
| This attribute fixes which signaling protocol is used at this port (D-Channel). It is equivalent to isdnSignalingProtocol in the isdn MIB. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), etsi(3), ess5(6), dms100(7), ni1(9), ni2(10), ins64(17), ins1500(18), qsig(21), notApplicable(255) | ||
| prtIsdnBasicRateLineTopology | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.6 | ||
| This attribute is relevant for ISDN BRI only. It is equivalent to isdnBasicRateLineTopology in the isdn MIB. | |||
| OBJECT-TYPE | |||
| INTEGER | pointToPoint(1), pointToMultipoint(2), notApplicable(255) | ||
| prtIsdnMode | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.7 | ||
| This attribute allows the user to configure the port as leased(2) in case of connection to a TDM network. | |||
| OBJECT-TYPE | |||
| INTEGER | dialup(1), leased(2), syncLeased(3), notApplicable(255) | ||
| prtIsdnFilter | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.8 | ||
| This attribute allows the user to configure the port: answerAll(2): accept all incoming calls, rejectAll(3): reject all incoming calls, selective(4): accept or reject according directory table. callBack (5): In this mode the ISDN Ch will reject incoming calls and will initiate call back to the rejected phone number. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), answerAll(2), rejectAll(3), selective(4), callBack(5) | ||
| prtIsdnSimultaneousCall | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.9 | ||
| In case of simultaneous call (local,remote and remote,local): accept(2): accept the incoming call, reject(3): reject the incoming call. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), accept(2), reject(3) | ||
| prtIsdnNumOfAbstractTerm | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.10 | ||
| An object for KM2100/4 agents. 255=Not Applicable When ISDN Standard = ETSI or NTT (European) the value should be 255 (NotApplicable) else If ML speed is 64Kbps value should be 1. If ML speed is 128Kbps value can be either 1 or 2 (user selection). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnSwitchMode | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.11 | ||
| For KM2100. auto - The call is initiated automatically by one of the IO cards connected to KML.10(ISDN card) having ISDN Switch Mode. manual - The call is initiated by the user manually, for KML.10 having ISDN Switch Mode (via mdlSCmd). connect- The call is initiated 'immediately', for KML.10 having ISDN Switch Mode. 'immediately'- means: immediately after power-up (when product performed Reset) OR, since this value appears in the active configuration. In this case, the call can be disconnected only by power-off of the product or by changing this object to another value (or actual Remove of the KML.10 relevant card). notApplicable - For other card types. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), auto(2), manual(3), connect(4) | ||
| prtIsdnAbSide | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.12 | ||
| This parameter indicates the QSIG side in layer 3. This definition is from the QSIG Standard. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), aSide(2), bSide(3) | ||
| prtIsdnQsigRole | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.13 | ||
| This parameter indicates the QSIG side in layer 1 & 2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), slave(2), master(3) | ||
| prtIsdnInterface | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.14 | ||
| It indicates the interface type: lt = line termination nt = network termination te = terminal equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | lt(1), nt(2), te(3), notApplicable(255) | ||
| prtIsdnCallMode | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.15 | ||
| This object indicates the acceptance of incoming calls. Initiate - Callout Listen - Callin. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), initiate(2), listen(3) | ||
| prtIsdnCallBackTimeout | 1.3.6.1.4.1.164.3.2.3.2.16.1.1.16 | ||
| This object is applicable only if 'prtIsdnFilter' is 'CallBack' and determines how long to wait from receiving the incoming call until initiating the call back call. The vaules range should be '1..20 sec' and the default 10 sec. | |||
| OBJECT-TYPE | |||
| INTEGER | |||
| prtIsdnEndpointTable | 1.3.6.1.4.1.164.3.2.3.2.16.2 | ||
| The write operation into the table objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIsdnEndpointEntry | |||
| prtIsdnEndpointEntry | 1.3.6.1.4.1.164.3.2.3.2.16.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIsdnEndpointEntry | |||
| prtIsdnEndpointCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIsdnEndpointSltIdx | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB' | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255) | ||
| prtIsdnEndpointPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.3 | ||
| This attribute indicates a unique port number. For MAXcess the values will be: exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), For KM-2100 the port index is calculated as follows: 100*Slot+Ch | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnEndpointIdx | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.4 | ||
| Since more than one endpoint may be defined per isdn entity, this field is a simple index. It corresponds to isdnEndpointIdx in the isdn MIB. | |||
| OBJECT-TYPE | |||
| INTEGER | atei1(1), atei2(2) | ||
| prtIsdnEndpointTeiType | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.5 | ||
| The type of TEI (Terminal Endpoint Identifier) used for this Terminal Endpoint. In case of dynamic(1), the TEI value is selected by the switch. In case of static(2), a valid TEI value has to be entered in the isdnEndpointTeiValue object. interface type as well as the Terminal Endpoint type. static(2). On Basic Rate interfaces the default value is dynamic(1) for isdn(63) Terminal Endpoints. It corresponds to isdnEndpointTeiType in the isdn MIB. | |||
| OBJECT-TYPE | |||
| INTEGER | dynamic(1), static(2), notApplicable(255) | ||
| prtIsdnEndpointTeiValue | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.6 | ||
| When the TEI Type is static, the value of the TEI should be between 0 and 63. Else, it is not selectable by user. 255 = notApplicable. It corresponds to isdnEndpointTeiValue in the isdn MIB | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnEndpointSpid | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.7 | ||
| The Service profile IDentifier (SPID) information for this Terminal Endpoint. It is is composed of 9-20 numeric characters. It corresponds to isdnEndpointSpid in the isdn MIB. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| prtIsdnEndpointBearerCh | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.8 | ||
| This is the selected dialing channel. anyChannel - the system selects the dialing channel. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), anyChannel(2), channelB1(3), channelB2(4) | ||
| prtIsdnEndpointRowStatus | 1.3.6.1.4.1.164.3.2.3.2.16.2.1.9 | ||
| This field indicates whether to consider this endpoint or not. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| prtIsdnDirectoryTable | 1.3.6.1.4.1.164.3.2.3.2.16.3 | ||
| The write operation into the table objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIsdnDirectoryEntry | |||
| prtIsdnDirectoryEntry | 1.3.6.1.4.1.164.3.2.3.2.16.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIsdnDirectoryEntry | |||
| prtIsdnDirectoryCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIsdnDirectorySltIdx | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.2 | ||
| This attribute indicates a unique slot position where the card is inserted. For MX300/30 ports: io1(5) = isdn1(5) and io2(6) = isdn2(6). In ?004 Unit the entries io6(10)..io12(16) are not valid For KM2100/4 Valid entries are 'kmxMlA ' or 'kmxMlB' | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), kmxMlA(103), kmxMlB(104), notApplicable(255) | ||
| prtIsdnDirectoryPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.3 | ||
| For MAXcess this is the internal port number: 101, 102,.... For KM-2100 the port index is calculated as follows: 100*Slot+Ch | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnDirectoryLocalAddr | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.4 | ||
| This is the local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(17..20) | ||
| prtIsdnDirectoryLocalSubAddr | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.5 | ||
| This is the local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(4..6) | ||
| prtIsdnDirectoryRemoteAddr | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.6 | ||
| This is the remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(17..20) | ||
| prtIsdnDirectoryRemoteSubAddr | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.7 | ||
| This is the remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(4..6) | ||
| prtIsdnDirectoryPrtNu | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.8 | ||
| This is the external port number connected to this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnDirectoryTeiId | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.9 | ||
| This is the abstract terminal id if relevant, connected to this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIsdnDirectoryRowStatus | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.10 | ||
| This is the status for the row. It allows to know whether to consider this row or not. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| prtIsdnDirectoryLocalAddr2 | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.11 | ||
| This is the second local address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank (20 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(17..20) | ||
| prtIsdnDirectoryLocalSubAddr2 | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.12 | ||
| This is the second local subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(4..6) | ||
| prtIsdnDirectoryRemoteAddr2 | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.13 | ||
| This is the second remote address associated with this entry. - For MX: Size=17 , Default=0 (17 characters) - For KM: Size=20, Default=blank(20 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(17..20) | ||
| prtIsdnDirectoryRemoteSubAddr2 | 1.3.6.1.4.1.164.3.2.3.2.16.3.1.14 | ||
| This is the second remote subaddress associated with this entry. - For MX: Size=6 , Default=0 (6 characters) - For KM: Size=4 , Default=blank (4 characters) | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(4..6) | ||
| prtLogicalCnfg | 1.3.6.1.4.1.164.3.2.3.2.17 | ||
| OBJECT IDENTIFIER | |||
| prtLogicalCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.17.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtLogicalCnfgEntry | |||
| prtLogicalCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.17.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtLogicalCnfgEntry | |||
| prtLogicalCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtLogicalSltIdx | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.2 | ||
| Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6). | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtLogicalPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.3 | ||
| This attribute indicates a unique port number. This port number should be an internal port number: inPrt1(101)->inPrt50(150), linkSel1(200)->linkSel50(250), encaps1(300)-> encaps50(350), huntGr1(101) -> huntGr10(110). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtLogicalConnect | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.4 | ||
| This attribute indicates whether the port should be considered in any of the mux algorithms. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtLogicalFunction | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.5 | ||
| This parameter defines the function of the relevant channel. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), linkSelector(2), encapsulator(3), huntGroup(4) | ||
| prtLogicalRowStatus | 1.3.6.1.4.1.164.3.2.3.2.17.1.1.6 | ||
| This parameter allows the NMS to create/delete logical ports. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| linkSelectorCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.17.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinkSelectorCnfgEntry | |||
| linkSelectorCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.17.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| LinkSelectorCnfgEntry | |||
| linkSelectorCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| linkSelectorSltIdx | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.2 | ||
| Slot Index | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| linkSelectorPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.3 | ||
| This attribute indicates a unique port number. This port number should be internal port number: higher or equal to linkSeL1(201). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| linkSelectorMaxIdleTime | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.4 | ||
| Move to higher prioritized connected link after this period of seconds of silence on the current link. 0=move immediately to higher prioritized connected link. UNIT is seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| linkSelectorMode | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.5 | ||
| If the link selector is in mode: backup(2)=then the link with the lower priority will be used in case of failure of the higher priority link, bod(3)=bandwidth on demand or dynamic bandwidth allocation means that links with lower priority will be used whenever additional bandwidth is required. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), backup(2), bod(3) | ||
| linkSelectorRevert | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.6 | ||
| If the link selector is in mode backup: auto(2)=return automatically to Main link when it is OK. manual(3)=stays connected to backup link. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), auto(2), manual(3) | ||
| linkSelectorMinBUSession | 1.3.6.1.4.1.164.3.2.3.2.17.2.1.7 | ||
| Minimum duration of a backup session before returning to Main Link. Relevant in Backup Mode and when Revert is auto(2). Value 255 is for NEVER which means never return to Main Link. UNIT is minutes. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| linkSelectorPLinkTable | 1.3.6.1.4.1.164.3.2.3.2.17.3 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LinkSelectorPLinkEntry | |||
| linkSelectorPLinkEntry | 1.3.6.1.4.1.164.3.2.3.2.17.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| LinkSelectorPLinkEntry | |||
| pLinkCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pLinkSltIdx | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.2 | ||
| Slot Index | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| pLinkPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.3 | ||
| This attribute indicates a unique port number. This port number should be the link selector number. | |||
| OBJECT-TYPE | |||
| Integer32 | 200..250 | ||
| pLinkIdx | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.4 | ||
| This index is the row number. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| pLinkSlotNu | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.5 | ||
| The slot of the prioritized link. For ISDN BRI ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6). | |||
| OBJECT-TYPE | |||
| INTEGER | noConnect(2), cl(3), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| pLinkPortNu | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.6 | ||
| The port of the prioritized link. Value 100 is for noConnect. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pLinkPrioNu | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.7 | ||
| The priority of the prioritized link. MIN=1...., MAX=8. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| pLinkVRate | 1.3.6.1.4.1.164.3.2.3.2.17.3.1.8 | ||
| The rate to use with this link. | |||
| OBJECT-TYPE | |||
| INTEGER | r1x56eq56Kbps(1), r1x64eq64Kbps(2), r2x56eq112Kbps(3), r2x64eq128Kbps(4), r3x56eq168Kbps(5), r3x64eq192Kbps(6), r4x56eq224Kbps(7), r4x64eq256Kbps(8), r5x56eq280Kbps(9), r5x64eq320Kbps(10), r6x56eq336Kbps(11), r6x64eq384Kbps(12), r7x56eq392Kbps(13), r7x64eq448Kbps(14), r8x56eq448Kbps(15), r8x64eq512Kbps(16), r9x56eq504Kbps(17), r9x64eq576Kbps(18), r10x56eq560Kbps(19), r10x64eq640Kbps(20), r11x56eq616Kbps(21), r11x64eq704Kbps(22), r12x56eq672Kbps(23), r12x64eq768Kbps(24), r13x56eq728Kbps(25), r13x64eq832Kbps(26), r14x56eq784Kbps(27), r14x64eq896Kbps(28), r15x56eq840Kbps(29), r15x64eq960Kbps(30), r16x56eq896Kbps(31), r16x64eq1024Kbps(32), r17x56eq952Kbps(33), r17x64eq1088Kbps(34), r18x56eq1008Kbps(35), r18x64eq1152Kbps(36), r19x56eq1064Kbps(37), r19x64eq1216Kbps(38), r20x56eq1120Kbps(39), r20x64eq1280Kbps(40), r21x56eq1176Kbps(41), r21x64eq1344Kbps(42), r22x56eq1232Kbps(43), r22x64eq1408Kbps(44), r23x56eq1288Kbps(45), r23x64eq1472Kbps(46), r24x56eq1344Kbps(47), r24x64eq1536Kbps(48), r25x56eq1400Kbps(49), r25x64eq1600Kbps(50), r26x56eq1456Kbps(51), r26x64eq1664Kbps(52), r27x56eq1512Kbps(53), r27x64eq1728Kbps(54), r28x56eq1568Kbps(55), r28x64eq1792Kbps(56), r29x56eq1624Kbps(57), r29x64eq1856Kbps(58), r30x56eq1680Kbps(59), r30x64eq1920Kbps(60), r31x56eq1736Kbps(61), r31x64eq1984Kbps(62), noRate(100) | ||
| prtFrPlusCnfg | 1.3.6.1.4.1.164.3.2.3.2.18 | ||
| OBJECT IDENTIFIER | |||
| prtFrPlusCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.18.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtFrPlusCnfgEntry | |||
| prtFrPlusCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.18.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtFrPlusCnfgEntry | |||
| prtFrPlusCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.18.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtFrPlusSltIdx | 1.3.6.1.4.1.164.3.2.3.2.18.1.1.2 | ||
| Slot Index. For ISDN BRI Ports of MX300/30, io1(5) = isdn1(5) and io2(6) = isdn2(6). | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| prtFrPlusPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.18.1.1.3 | ||
| This attribute indicates a unique port number. This port number should be: - for ISDN cards: inPrt1(101)->inPrt50(150) - for MHS1 card : exPrt1(1) - for MHS3, MLS3 cards: exPrt1(1)->exPrt3(3) - for MLS6 cards: exPrt1(1)->exPrt6(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtFrPlusNotSegmentedPriorities | 1.3.6.1.4.1.164.3.2.3.2.18.1.1.4 | ||
| This parameter is relevant only for FR+ protocol and asks the MXcess NOT to segment data with specified priorities: from LSB: bit 1 is for priority 1, bit 2 is for priority 2, .... till bit 7 for priority 7. - a priority selected to be segmented : its bit will be '0' - a priority not to be segmented : its bit will be '1' Default is 00000000; i.e, segment all priorities. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| prtMl4Cnfg | 1.3.6.1.4.1.164.3.2.3.2.19 | ||
| OBJECT IDENTIFIER | |||
| prtMl4CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.19.1 | ||
| This is an extension table for MTML-4 card parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMl4CnfgEntry | |||
| prtMl4CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.19.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtMl4CnfgEntry | |||
| prtMl4CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtMl4SltIdx | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtMl4PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.3 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), inPrt1(101), inPrt2(102), inPrt3(103), inPrt4(104) | ||
| prtMl4SigProfile | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.4 | ||
| This object indicates the Signaling Profile of the port. none - when the Frame is G732N (no MF). p1 = profile 1 p2 = profile 2 p3 = profile 3 p4 = profile 4 p5 = profile 5 | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), p1(3), p2(4), p3(5), p4(6), p5(7) | ||
| prtMl4CGA | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.5 | ||
| This object selects the method used to signal the CGA state to the other end, through the main link. 'none' - non-transparent mode. When one of the links (main) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos' will be transmitted to the other end. 'trans' - when one of the links (main) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos' will be transmitted to the other end. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), trans(2), full(3) | ||
| prtMl4Oos | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.6 | ||
| 'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0 | |||
| OBJECT-TYPE | |||
| INTEGER | notSupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6) | ||
| prtMl4VoiceOos | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.7 | ||
| Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtMl4DataOos | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.8 | ||
| Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtMl4Service | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.9 | ||
| Link Service. leasedLine - usual TDM interface. v51 - V5.1 interface. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), leasedLine(2), v51(3) | ||
| prtMl4IpAddress | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.10 | ||
| IP Address of the port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| prtMl4IpMask | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.11 | ||
| IP subnet mask of the port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| prtMl4SignalingMode | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.12 | ||
| Refers to the signaling mode of the Framer module. cas(2) means Channel Associated Signaling. Used for E1 Links. ccs(3) is the Common Channel Signaling (the signaling is not within the channels time slot - a TS for signaling is used). robbedBit(4) is a method implementing 7 bits for the voice and 1 bit dedicated for signaling. Used for T1 Links. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), cas(2), ccs(3), robbedBit(4) | ||
| prtMl4EchoCanceler | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.13 | ||
| Echo canceler activation. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtMl4OosErrorSource | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.14 | ||
| OOS (Out-of-Service) Error Source. This object is applicable for T1 ports only. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), framing(3), bpv(4) | ||
| prtMl4OosEntryThreshold | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.15 | ||
| This object defines the number of Errors per Second that determine the minimum unacceptable noise level. This value will be the Entry Threshold to the OOS (Out-of-Service) state. This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..999 | ||
| prtMl4OosExitThreshold | 1.3.6.1.4.1.164.3.2.3.2.19.1.1.16 | ||
| This object defines the number of consecutive Error-Free-Seconds before going from OOS state to Normal state. This value will be the Exit Threshold from the OOS (Out-of-Service) state. Units=seconds This object is applicable only when prtMl4OosErrorSource=framing(3) or bpv(4). 0=notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| prtAcmCnfg | 1.3.6.1.4.1.164.3.2.3.2.20 | ||
| OBJECT IDENTIFIER | |||
| prtAcmCnfgTable | 1.3.6.1.4.1.164.3.2.3.2.20.1 | ||
| This is a table for ACM port parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtAcmCnfgEntry | |||
| prtAcmCnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.20.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtAcmCnfgEntry | |||
| prtAcmCnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtAcmSltIdx | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtAcmPrtIdx | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.3 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2), exPrt3(3), exPrt4(4), exPrt5(5), exPrt6(6), exPrt7(7), exPrt8(8), exPrt9(9), exPrt10(10), exPrt11(11), exPrt12(12) | ||
| prtAcmConnect | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.4 | ||
| This attribute indicates whether the port should be connected or not. Only a connected port can perform activity. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtAcmActiveState | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.5 | ||
| This attribute indicates the Electric Active State of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | low(2), high(3) | ||
| prtAcmAlrString | 1.3.6.1.4.1.164.3.2.3.2.20.1.1.6 | ||
| Alarm string selected by user for the Inbound ports. This object is applicable only for the Inbound Ports: ext-5..ext-12. For the Outbound Ports (ext-1..ext-4), the size of this string will be 0. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..35) | ||
| prtE2Cnfg | 1.3.6.1.4.1.164.3.2.3.2.21 | ||
| OBJECT IDENTIFIER | |||
| prtE2CnfgTable | 1.3.6.1.4.1.164.3.2.3.2.21.1 | ||
| This is a table for E2 port parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtE2CnfgEntry | |||
| prtE2CnfgEntry | 1.3.6.1.4.1.164.3.2.3.2.21.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtE2CnfgEntry | |||
| prtE2CnfgIdx | 1.3.6.1.4.1.164.3.2.3.2.21.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. The write operation is valid only to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtE2SltIdx | 1.3.6.1.4.1.164.3.2.3.2.21.1.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16) | ||
| prtE2PrtIdx | 1.3.6.1.4.1.164.3.2.3.2.21.1.1.3 | ||
| This attribute indicates a unique port number. | |||
| OBJECT-TYPE | |||
| INTEGER | exPrt1(1), exPrt2(2) | ||
| prtE2Connect | 1.3.6.1.4.1.164.3.2.3.2.21.1.1.4 | ||
| This attribute indicates whether the port should be connected or not. Only a connected port can perform activity. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtE2MngOnNationalBit | 1.3.6.1.4.1.164.3.2.3.2.21.1.1.5 | ||
| This attribute indicates whether National Bit will be used for Management or not. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| dacsMux | 1.3.6.1.4.1.164.3.3 | ||
| OBJECT IDENTIFIER | |||
| dacsMuxEvents | 1.3.6.1.4.1.164.3.3.0 | ||
| The events for DACS MUX. | |||
| OBJECT-IDENTITY | |||
| sanityCheckTrap | 1.3.6.1.4.1.164.3.3.0.1 | ||
| This trap is sent after a data base download attempt. It returns the sanity result status and the configuration no.checked. | |||
| NOTIFICATION-TYPE | |||
| sysSSanityCheckStatus | |||
| sysDbaseDownloadCnfgIdxCmd | |||
| dacsMuxAlarmsTrap | 1.3.6.1.4.1.164.3.3.0.2 | ||
| This trap is sent when an alarm occurs. | |||
| NOTIFICATION-TYPE | |||
| mdlConnectTrap | 1.3.6.1.4.1.164.3.3.0.3 | ||
| This trap is sent when a card is removed. | |||
| NOTIFICATION-TYPE | |||
| mdlSCardType | |||
| mdlSActivity | |||
| sysAlrStatusTrap | 1.3.6.1.4.1.164.3.3.0.4 | ||
| This trap is sent upon any change in the value of any of the variables. | |||
| NOTIFICATION-TYPE | |||
| sysSAlrStatusAll | |||
| sysSAlrStatus | |||
| sysStatusChangedTrap | 1.3.6.1.4.1.164.3.3.0.5 | ||
| This trap is sent when Leds status is changed. | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| cnfgUpdateTrap | 1.3.6.1.4.1.164.3.3.0.6 | ||
| This trap is sent upon change of the active Configuration DB. | |||
| NOTIFICATION-TYPE | |||
| systemDacsMux | 1.3.6.1.4.1.164.3.3.1 | ||
| OBJECT IDENTIFIER | |||
| sysSa | 1.3.6.1.4.1.164.3.3.1.1 | ||
| OBJECT IDENTIFIER | |||
| sysSaSwchStatus | 1.3.6.1.4.1.164.3.3.1.1.1 | ||
| This object indicates the status of the switches on the SA unit. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits. For SMODs products see modem's specification. For DXC product see the following: There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (2**1 + 2**0). When the status of the switches is unknown, the value of this object will be 255. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSaSwRevision | 1.3.6.1.4.1.164.3.3.1.1.2 | ||
| This object indicates the Software revision of the system. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysSaHwVersion | 1.3.6.1.4.1.164.3.3.1.1.3 | ||
| This object indicates the Hardware version of the system. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysSaPorts | 1.3.6.1.4.1.164.3.3.1.1.4 | ||
| This object indicates the ports that are present in the system. Each possible port is represented by a bit. The value of this object is a sum of 2**n, n=number of bits. '1' - means that the port exists '0' - means that the port does not exist For detailed bit assignment, see product's spec. Bit 0 = LSB When this object is not relevant, the value will be 0. In some cases, this object may represent ports configuration of the system AND its far-end unit. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSaReadSwch | 1.3.6.1.4.1.164.3.3.1.1.5 | ||
| This object indicates wether the configuration will be read from the DIP switches on the SA (stand alone) unit. Each switch is represented by a bit. If the bit is 1: the configuration will be read from the HW switch position. If the bit is 0: the configuration will be read from the SW user configuration. The DIP switches are different in each of the RAD devices. In the Tiny Router (starting from the LSB) the following switches exist: Bit 0: WAN Loop Bit 1: LAN Full Duplex (When LAN AUI connector, it is SQE) Bit 2: PPP (When WAN 4 Wire connector, it is LONG) Bit 3: IP Learn | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysHub | 1.3.6.1.4.1.164.3.3.1.2 | ||
| OBJECT IDENTIFIER | |||
| sysChas | 1.3.6.1.4.1.164.3.3.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| chassTotalNoOfSlt | 1.3.6.1.4.1.164.3.3.1.2.1.1 | ||
| This object indicates the number of physical slots in the Hub chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chassTotalNoOfIoSlt | 1.3.6.1.4.1.164.3.3.1.2.1.2 | ||
| This object indicates the total number of physical IO slots in the chassis, (not all slots must be occupied and active). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chassTotalNoOfPsSlt | 1.3.6.1.4.1.164.3.3.1.2.1.3 | ||
| This object indicates the number of physical Power Supply slots in the chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chassTotalNoOfClSlt | 1.3.6.1.4.1.164.3.3.1.2.1.4 | ||
| This object indicates the number of physical Common Logic slots in the chassis. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| chassTotalNoOfMlSlt | 1.3.6.1.4.1.164.3.3.1.2.1.5 | ||
| This object indicates the number of physical Main Link slots in the chassis (Kmux). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysDcl | 1.3.6.1.4.1.164.3.3.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| sysDclTable | 1.3.6.1.4.1.164.3.3.1.2.2.1 | ||
| All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysDclEntry | |||
| sysDclEntry | 1.3.6.1.4.1.164.3.3.1.2.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysDclEntry | |||
| sysDclCnfgIdx | 1.3.6.1.4.1.164.3.3.1.2.2.1.1.1 | ||
| This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysDclRedundancy | 1.3.6.1.4.1.164.3.3.1.2.2.1.1.2 | ||
| DCL redundancy desired state. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysDclActiveCl | 1.3.6.1.4.1.164.3.3.1.2.2.1.1.3 | ||
| Active desired DCL. When 'auto' is selected, the system automatically selects the active DCL. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), dclA(2), dclB(3) | ||
| sysDclFlipDelay | 1.3.6.1.4.1.164.3.3.1.2.2.1.1.4 | ||
| If one DCL flip occured and a second one should be performed, the time from the previous flip is checked. If the time is shorter than the delay specified here (in minutes), the system should delay the flip operation until time reaches the specified delay. | |||
| OBJECT-TYPE | |||
| INTEGER | t1min(1), t2min(2), t3min(3), t4min(4) | ||
| sysDclFlipUponStnClk | 1.3.6.1.4.1.164.3.3.1.2.2.1.1.5 | ||
| This object allows user to decide (yes/no) if Agent should Flip from one DCL card to another, when there is Station Clock Fail in the Online DCL card. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| sysDclOnline | 1.3.6.1.4.1.164.3.3.1.2.2.2 | ||
| The active Dcl card of the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | dclA(1), dclB(2) | ||
| sysDclCopyDbTable | 1.3.6.1.4.1.164.3.3.1.2.2.3 | ||
| This table enables to copy a cofiguration from the Offline Dcl to the Online Dcl. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysDclCopyDbEntry | |||
| sysDclCopyDbEntry | 1.3.6.1.4.1.164.3.3.1.2.2.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysDclCopyDbEntry | |||
| sysDclCopyDbIdx | 1.3.6.1.4.1.164.3.3.1.2.2.3.1.1 | ||
| This object indicates the Idx of the Cnfg(1..255) being accessed. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysDclCopyDbCmd | 1.3.6.1.4.1.164.3.3.1.2.2.3.1.2 | ||
| When this command is sent to the agent, on(3), the Database specified (Db Idx), will be copied from the Offline Dcl to the Online Dcl. Afterwards the value of this object will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysStatus | 1.3.6.1.4.1.164.3.3.1.3 | ||
| OBJECT IDENTIFIER | |||
| sysSDateFormat | 1.3.6.1.4.1.164.3.3.1.3.1 | ||
| This object indicates the date and time format used for the sysSDateAndTimeCmd and for the alarm buffer report. | |||
| OBJECT-TYPE | |||
| INTEGER | ddMMYYYY(1), mmDDYYYY(2), yyyyMMDD(4) | ||
| sysSDateCmd | 1.3.6.1.4.1.164.3.3.1.3.2 | ||
| This object indicates the current date as it is known by the agent using its own real-time clock. The format would be as specified by the sysSDateFormat. This parameter can be set for time synchronization between the NMS and the Agent. * For KM-2100 V1 and FCD-T1/E1 - the string should contain '/' signs between day, month and year. Example: 12/08/1998. * For DXC and rest of the products - the string should contain '-' signs between day, month and year. Example: 12-08-1998. The day value will be in the range: 1..31. The month value will be in the range: 1..12. The year value will be in the range: 1996..2050 for products supporting the '-' format. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysSTimeCmd | 1.3.6.1.4.1.164.3.3.1.3.3 | ||
| This object indicates the current time as it is known by the agent using its own real-time clock. This parameter can be set for time synchronization between the NMS and the Agent. The string should contain ':' signs between hour, minute and second. Example: 11:05:58. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysSActiveCnfg | 1.3.6.1.4.1.164.3.3.1.3.4 | ||
| This object specifies the configuration number, that is currently active and running. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSEditCnfg | 1.3.6.1.4.1.164.3.3.1.3.5 | ||
| This object indicates the unique configuration number that is currently loaded into the tmp working space for manipulation and update operations. Value of 255 means no config. is under editing process. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSEditBy | 1.3.6.1.4.1.164.3.3.1.3.6 | ||
| This entry indicates which MMI application is working on the edited config. The editing phase starts at the first modify operation and ends after a load operation. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), snmp(2), terCon1(3), terCon2(4), terInbandCon1(5), terInbandCon2(6), lcd(7) | ||
| sysSClkSrc | 1.3.6.1.4.1.164.3.3.1.3.7 | ||
| This entry indicates the source of the system clock. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), fallback(2), internal(3), ml(4) | ||
| sysSAlrStatus | 1.3.6.1.4.1.164.3.3.1.3.8 | ||
| Indicates the current alarm state only for system level. This object will be : - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), major(3), minor(4), event(5), warning(6), critical(7) | ||
| sysSAlrStatusAll | 1.3.6.1.4.1.164.3.3.1.3.9 | ||
| Indicates the current alarm state including all levels: system, card, port. - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), major(3), minor(4), event(5), warning(6), critical(7) | ||
| sysSTestStatus | 1.3.6.1.4.1.164.3.3.1.3.10 | ||
| Indicates the current test status (for all levels: system, card, port). This attribute will be set to: - on(3): when there is at least one test in progress on the system/card/port otherwise the value will be off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSSanityCheckStatus | 1.3.6.1.4.1.164.3.3.1.3.11 | ||
| Upon completion of the Sanity Check process on the TmpCnfg this object will be set to: - fail(2): when there is at least one error (which is not just a warning) encountered otherwise, - warning(3): when there are only warnings otherwise, - ok(4). The value should be unknown(1), if the TmpCnfg was changed after the last Sanity check. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), fail(2), warning(3), ok(4) | ||
| sysSNoOfSanityCheckErr | 1.3.6.1.4.1.164.3.3.1.3.12 | ||
| This object indicates the number of errors/warnings discovered by the last Sanity Check process. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSErrListTable | 1.3.6.1.4.1.164.3.3.1.3.13 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysSErrListEntry | |||
| sysSErrListEntry | 1.3.6.1.4.1.164.3.3.1.3.13.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysSErrListEntry | |||
| sysSErrType | 1.3.6.1.4.1.164.3.3.1.3.13.1.1 | ||
| The errors are recorded in the agent, in two separate lists, according to their type: error or warning. | |||
| OBJECT-TYPE | |||
| INTEGER | error(1), warning(2) | ||
| sysSErrIdx | 1.3.6.1.4.1.164.3.3.1.3.13.1.2 | ||
| Unique index number to identify an entry in the error or warning list . The maximum value cannot exceed the value of 'sysSNoOfSanityCheckErr' (actually, the sum of the Errors list max. index and the Warning list max. index should equal the value of'sysSNoOfSanityCheckErr'). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSErrDescription | 1.3.6.1.4.1.164.3.3.1.3.13.1.3 | ||
| This object is a full text description of the sanity check error including error code, IO slot and port numbers related to the code . | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysSMaxNoOfCnfg | 1.3.6.1.4.1.164.3.3.1.3.14 | ||
| Maximum number of configurations that can be defined and stored in the DACS agent. If the DACS agent has a large capacity, the maximum will be limited to 254. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSSelfTestResult | 1.3.6.1.4.1.164.3.3.1.3.15 | ||
| The test is performed by the active Common Logic card. The result will be a sum of 2**n according to the following bit convention: For DXC: bit 0 Database 1 Checksum Error (LSB) bit 1 Database 2 Checksum Error bit 2 I/O Expander Error bit 3 Counter Error bit 4 Matrix DPR Error bit 5 PS-A 5 Volt Error bit 6 PS-A 12 Volt Error bit 7 PS-B 5 Volt Error bit 8 PS-B 12 Volt Error bit 9 EPROM Failure For FCD: bit 0 I/O Expander Error (LSB) bit 1 Counter Error bit 2 EPROM Failure bit 3 Illegal Sys Config bit 4 SFIFO bit 5 EPIC Failure (ISDN) bit 6 XL Flash Fail -- for MSDSL interface bit 7 XL MITEL Fail -- for MSDSL interface bit 8 XL Framer Fail -- for MSDSL interface bit 9 XL DSP Fail -- for MSDSL interface For LRS52 - refer to product's spec When a bit is ('1'), the error exists. When NO ERROR is encountered, this object's value will be 0. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSRelayState | 1.3.6.1.4.1.164.3.3.1.3.16 | ||
| Indicates the current state of the alarm relay. notApplicable - for agents that do not support this object. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| sysSInvertedAlr | 1.3.6.1.4.1.164.3.3.1.3.17 | ||
| Indicates if there is any Inverted alarm at any level of the system (sys, card, port). notApplicable - for agents that do not support this object. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| sysSRdnFlipTable | 1.3.6.1.4.1.164.3.3.1.3.18 | ||
| This table includes all the Flip events due to I/O Redundancy since last Clear command of this table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysSRdnFlipEntry | |||
| sysSRdnFlipEntry | 1.3.6.1.4.1.164.3.3.1.3.18.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysSRdnFlipEntry | |||
| sysSRdnFlipIdx | 1.3.6.1.4.1.164.3.3.1.3.18.1.1 | ||
| Unique index number to identify an entry in the Redundancy Flip list. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSRdnFlipSlot | 1.3.6.1.4.1.164.3.3.1.3.18.1.2 | ||
| The slot number from which Flip was performed. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| sysSRdnFlipPort | 1.3.6.1.4.1.164.3.3.1.3.18.1.3 | ||
| The port number from which Flip was performed. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 100=notApplicable (when Redundancy is at card level). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSRdnFlipCause | 1.3.6.1.4.1.164.3.3.1.3.18.1.4 | ||
| The last cause that caused the Flip from the Slot (Port) of sysSRdnSlot, sysSRdnPort. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| sysSRdnFlipDate | 1.3.6.1.4.1.164.3.3.1.3.18.1.5 | ||
| Flip event Date. The format will be the one selected by user for sysSDateFormat. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| sysSRdnFlipTime | 1.3.6.1.4.1.164.3.3.1.3.18.1.6 | ||
| Flip event Time. The format will be hh:mm:ss. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| sysSRdnFlipTableClearCmd | 1.3.6.1.4.1.164.3.3.1.3.19 | ||
| This command, when Set to 'on', clears the Redundancy Flip table (sysSRdnFlipTable). After clear is performed, the agent will turn the value to 'off' automatically. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSRdnFlipCmd | 1.3.6.1.4.1.164.3.3.1.3.20 | ||
| This object enables the user to send a command to the Agent, to Flip from a current Online IO card to its Redundant card. The value sent will be an Object Identifier of an entry in the sysCRdnTable. This entry defines the Redundant couple of Slots on which the Flip is applied. Setting this object, will cause the Agent to Flip from current Online card to its Redundant card. This manual flip command is applicable only for entries having Redundancy Mode=Y Cable. Agent will send the value 0 for Get. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| sysSBusTable | 1.3.6.1.4.1.164.3.3.1.3.21 | ||
| This table includes data and status about the internal DXC BUS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysSBusEntry | |||
| sysSBusEntry | 1.3.6.1.4.1.164.3.3.1.3.21.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysSBusEntry | |||
| sysSBusPortIdx | 1.3.6.1.4.1.164.3.3.1.3.21.1.1 | ||
| The DXC BUS port number: - first two digits will be: (IO slot number+10) - last one/two digits will be the Bus port number, in odd numbers: port1 = 1 port2 = 3 Example: port2 of IO slot 11 will be: 213. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSBusStatus | 1.3.6.1.4.1.164.3.3.1.3.21.1.2 | ||
| The Status of sysSBusPortIdx. free - not used physical - captured by the port of the card physically installed virtual - captured virtually by another port. Example: DIM port (by Destination) or by Transparent T3/E3 port. | |||
| OBJECT-TYPE | |||
| INTEGER | free(1), physical(2), virtual(3) | ||
| sysSBusCapturePort | 1.3.6.1.4.1.164.3.3.1.3.21.1.3 | ||
| The Port that Captured the sysSBusPortIdx. - if sysSBusStatus=free, the value will be 'none'=0 - else, if sysSBusStatus=fixed, the value will be: sysSBusPortIdx - else, the value will be according to the port index that captured this Bus Port (according to DXC port index convention): - xx1, xx3, xx11, xx13, xx31, xx33, xx2..xx56(even numbers) - xx = (IO slot number+10) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSBusUtilization | 1.3.6.1.4.1.164.3.3.1.3.21.1.4 | ||
| Utilization of sysSBusPortIdx resources, in percent [%]. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSRdnCmdTable | 1.3.6.1.4.1.164.3.3.1.3.22 | ||
| This table includes commands used for IO Redundancy. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysSRdnCmdEntry | |||
| sysSRdnCmdEntry | 1.3.6.1.4.1.164.3.3.1.3.22.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysSRdnCmdEntry | |||
| sysSRdnEnforcedChannel | 1.3.6.1.4.1.164.3.3.1.3.22.1.1 | ||
| This is a command to override all switching considerations and enforce use of primary/ secondary connection only. noEnforcement - cancels the state of override and goes back to usual switching considerations. Default = noEnforcement(2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), noEnforcement(2), primary(3), secondary(4) | ||
| sysCurrentAlr | 1.3.6.1.4.1.164.3.3.1.4 | ||
| OBJECT IDENTIFIER | |||
| sysSAlrTable | 1.3.6.1.4.1.164.3.3.1.4.1 | ||
| List of system level current existing alarms . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysSAlrEntry | |||
| sysSAlrEntry | 1.3.6.1.4.1.164.3.3.1.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysSAlrEntry | |||
| sysSAlrIdx | 1.3.6.1.4.1.164.3.3.1.4.1.1.1 | ||
| An index number of the current system alarms. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSAlrCode | 1.3.6.1.4.1.164.3.3.1.4.1.1.2 | ||
| This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSAlrState | 1.3.6.1.4.1.164.3.3.1.4.1.1.3 | ||
| This object indicates the alarm Severity. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| sysSAlarmMask | 1.3.6.1.4.1.164.3.3.1.4.1.1.4 | ||
| Alarm Mask is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlarmInvert | 1.3.6.1.4.1.164.3.3.1.4.1.1.5 | ||
| Alarm Invert is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlarmOnOff | 1.3.6.1.4.1.164.3.3.1.4.1.1.6 | ||
| Alarm state is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlarmCounter | 1.3.6.1.4.1.164.3.3.1.4.1.1.7 | ||
| A counter - how many times the alarm occured (ON) since last clear operation or since last Reset. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysSAlrClearCmd | 1.3.6.1.4.1.164.3.3.1.4.2 | ||
| Setting this attribute to ON, will enforce a clear operation on the system level alarms . Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlrClearAllCmd | 1.3.6.1.4.1.164.3.3.1.4.3 | ||
| Setting this attribute to ON, will enforce a clear operation on all levels alarms . Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlrMaskAll | 1.3.6.1.4.1.164.3.3.1.4.4 | ||
| on(3) - will cause masking of all the system level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all system level alarms except those masked via the sysSAlrMask. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysSAlrMask | 1.3.6.1.4.1.164.3.3.1.4.5 | ||
| This object is a mask that indicates which system level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the system level will be 0. This object is applicable only when sysSAlrMaskAll=off (otherwise all system alarms are masked). Example: When Alarms having the codes 6 and 11 are masked, the value of this object will be 840 (hex). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| sysSAlrDataUpdateCmd | 1.3.6.1.4.1.164.3.3.1.4.6 | ||
| on(3) - will cause Update of the Alarms Severity, Attributes and Report tables. off(2) - Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysBufferAlr | 1.3.6.1.4.1.164.3.3.1.5 | ||
| OBJECT IDENTIFIER | |||
| sysBufferAlrTable | 1.3.6.1.4.1.164.3.3.1.5.1 | ||
| List of current existing alarms (of all levels). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysBufferAlrEntry | |||
| sysBufferAlrEntry | 1.3.6.1.4.1.164.3.3.1.5.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysBufferAlrEntry | |||
| sysBufferAlrIdx | 1.3.6.1.4.1.164.3.3.1.5.1.1.1 | ||
| An index number of the current alarms. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysBufferAlrCode | 1.3.6.1.4.1.164.3.3.1.5.1.1.2 | ||
| This object indicates a code related to a specific alarm description. The list of codes and thir related descriptions will be known by the NMS (for display purpose) and will appear in the unit's user manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysBufferAlrState | 1.3.6.1.4.1.164.3.3.1.5.1.1.3 | ||
| This object indicates the alarm type. minor/major/warning/critical - indicates appearance of the problem and the type. event - indicates occurence of an event. off - indicates disappearance of an alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), event(3), minor(4), major(5), warning(6), critical(7) | ||
| sysBufferAlrSlot | 1.3.6.1.4.1.164.3.3.1.5.1.1.4 | ||
| The slot number this alarm refers to. When the alarm refers to a system function OR the DACS agent is a stand-alone unit, the value will be 'notApplicable(255)'. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255) | ||
| sysBufferAlrPort | 1.3.6.1.4.1.164.3.3.1.5.1.1.5 | ||
| The port number this alarm refers to. If the port number is irrelevant to this alarm (if it is a system/card level alarm) the value will be 9999. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysBufferAlrDate | 1.3.6.1.4.1.164.3.3.1.5.1.1.6 | ||
| The date when the alarm occured. The format will be according to sysSDateFormat. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysBufferAlrTime | 1.3.6.1.4.1.164.3.3.1.5.1.1.7 | ||
| The time when the alarm occured. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysBufferAlrClearCmd | 1.3.6.1.4.1.164.3.3.1.5.2 | ||
| Setting this attribute to ON, will enforce a clear operation on the Alarms Buffer. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysConfig | 1.3.6.1.4.1.164.3.3.1.6 | ||
| OBJECT IDENTIFIER | |||
| sysCClkSrcTable | 1.3.6.1.4.1.164.3.3.1.6.1 | ||
| All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysCClkSrcEntry | |||
| sysCClkSrcEntry | 1.3.6.1.4.1.164.3.3.1.6.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysCClkSrcEntry | |||
| sysCClkCnfgIdx | 1.3.6.1.4.1.164.3.3.1.6.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysCClkSrcIdx | 1.3.6.1.4.1.164.3.3.1.6.1.1.2 | ||
| An index in the table. There are only two entries in the table. master - refers Master clock parameters fallback - refers Fallback clock parameters | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), fallback(2) | ||
| sysCClkSrcMode | 1.3.6.1.4.1.164.3.3.1.6.1.1.3 | ||
| This entry indicates the source the nodal timing is locked to. none - is an invalid option for Master clock. internal - is an invalid option for Fallback clock . station - is an invalid option for a stand-alone unit. lbt - loop-back timing ntr - A system locked reference clock adaptive - clcok locking is achieved by altering the clock according to the data load notApplicable - for ML source of Kmux or ML Timing combinations when Master/Fallback clock are not applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), internal(2), rxClk(3), station(4), lbt(5), ntr(6), adaptive(7), notApplicable(255) | ||
| sysCClkSrcPrt | 1.3.6.1.4.1.164.3.3.1.6.1.1.4 | ||
| This entry is valid only when working in rxClk mode. For ACE2002 in case of invalid entry the return value will be 0. For other products in case of invalid entry the return value will be 9999. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The SP ports will be numbered as follows: - SP port 1 : 1 - SP port 2 : 2 For external ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Kmux, the port will be according to : Slot*100+Ch. For ACE2002 and LA140, the port will be ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCClkStationFreq | 1.3.6.1.4.1.164.3.3.1.6.1.1.5 | ||
| This entry indicates the frequency of the station clock when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), f1544Khz(2), f2048Khz(3) | ||
| sysCClkRevertiveTimeout | 1.3.6.1.4.1.164.3.3.1.6.1.1.6 | ||
| The time in seconds in which the system will monitor the higher level clock source, before decision to revert to that clock. In case the time is zero, revertive mode will be disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCClkStationIf | 1.3.6.1.4.1.164.3.3.1.6.1.1.7 | ||
| This entry indicates the electrical interface connected to the station clock, when the source is 'station'. The value will be applicable only when the sysCClkSrcMode is 'station'. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), g703(2), rs422(3) | ||
| sysCnfgTable | 1.3.6.1.4.1.164.3.3.1.6.2 | ||
| All the entries of this table are identical (have the same value) for all the configurations (1..255) except the TmpCnfg. The write operation into the Table Objects is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysCnfgEntry | |||
| sysCnfgEntry | 1.3.6.1.4.1.164.3.3.1.6.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysCnfgEntry | |||
| sysCnfgIdx | 1.3.6.1.4.1.164.3.3.1.6.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysCMatrixMode | 1.3.6.1.4.1.164.3.3.1.6.2.1.2 | ||
| Indicates the TS Matrix Mode: bidirectional - TS Assignment Matrix is symmetric. unidirectional - TS Assignment Matrix can be asymmetric. notApplicable - for agents that do not support this feature. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), bidirectional(2), unidirectional(3) | ||
| sysCIsdnFormat | 1.3.6.1.4.1.164.3.3.1.6.2.1.3 | ||
| ISDN format. This parameter controls the operation mode of the ISDN ports. te - ISDN timing is derived from the signal received from the equipment it is connected to. nt - timing of the transmit path is locked to the nodal timing source. notApplicable - for agents that do not support this feature. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), te(2), nt(3) | ||
| sysCRoutingOnEth | 1.3.6.1.4.1.164.3.3.1.6.2.1.4 | ||
| Mng Routing Protocol on the online CL Ethernet port. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| sysCAutoConfigEnable | 1.3.6.1.4.1.164.3.3.1.6.2.1.5 | ||
| This object enables user to enable/disable activating the Auto Configuration. When Auto Configuration is activated, the device learns its configuration Automatically from the Net it is connected to. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| sysCIntTsAllocMode | 1.3.6.1.4.1.164.3.3.1.6.2.1.6 | ||
| This object enables user to select the mode of Internal TS Allocation. static - user has to select for each Dynamic card port, the Maximum TSs expected to be connected (including future growth). This number will be allocated to the ports, so that if number of connected TSs will grow within the limits of this Maximum TS limit, no disruption of data flow will occur for other ports. dynamic- TS allocation is done dynamically according to the connected TSs. No future reservations are done. This mode may cause data disruption on other ports/slots if user will want to change the number of connected TSs for a Dynamic card port. Default=static(2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), static(2), dynamic(3) | ||
| sysCRdnTable | 1.3.6.1.4.1.164.3.3.1.6.3 | ||
| Configuration of all Redundant I/O cards and ports. The write operation into the table objects is valid only for the TmpCnfg. A Slot/Port that have no Redundancy, will not exist in this table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysCRdnEntry | |||
| sysCRdnEntry | 1.3.6.1.4.1.164.3.3.1.6.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysCRdnEntry | |||
| sysCRdnCnfgIdx | 1.3.6.1.4.1.164.3.3.1.6.3.1.1 | ||
| This object indicates the Idx of the Cnfg(1..255) being accessed ; Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnPrimeSlot | 1.3.6.1.4.1.164.3.3.1.6.3.1.2 | ||
| The slot number of the Primary card of Redundancy. The Primary card should be the card that user wishes to be the online card (usually the more important one). For some Redundancy modes the importance of the redundant cards/ports is the same. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| sysCRdnPrimePort | 1.3.6.1.4.1.164.3.3.1.6.3.1.3 | ||
| The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnSecSlot | 1.3.6.1.4.1.164.3.3.1.6.3.1.4 | ||
| The slot number of the Secondary card of Redundancy matching the Primary slot. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| sysCRdnSecPort | 1.3.6.1.4.1.164.3.3.1.6.3.1.5 | ||
| The port number. For DXC: For external ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For internal ports the convention used will be: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For MP: For external ports, the value will be as that of the port in the card. Example: external-3 -> 3 external-4 -> 4 For internal ports, the value will be 100 + the port in the card. Example: internal-1 -> 101 internal-4 -> 104 For IP Bundles, the value will be the Bundle ifIndex. For other products - refer to product specification. 100=notApplicable (when Redundancy is at card level). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnMode | 1.3.6.1.4.1.164.3.3.1.6.3.1.6 | ||
| Redundancy Mode. DXC supports: yCable(3), singleSlotProtection(6) and dualCableParallelTx(4) MP supports: dualCableAIS(2), yCable(3), dualCableParallelTx(4) and backup(5). backup - will be used when a port is backup of more than one port. IPmux: onePlusOne(7) and oneToOne(8) use for Bundle redundancy. | |||
| OBJECT-TYPE | |||
| INTEGER | dualCableAIS(2), yCable(3), dualCableParallelTx(4), backup(5), singleSlotProtection(6), onePlusOne(7), oneToOne(8) | ||
| sysCRdnRecMode | 1.3.6.1.4.1.164.3.3.1.6.3.1.7 | ||
| Recovery Mode. This object determines if after recovery of the failed card/port it will become on-line again or not: auto - automatic . In this case, the failed card/port will become on-line again after recovery, automatically. manual - In this case, the failed card/port will not become on-line again after recovery. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(2), manual(3) | ||
| sysCRdnRecTime | 1.3.6.1.4.1.164.3.3.1.6.3.1.8 | ||
| Redundancy Recovery Time (sec). After switching to the current online card, the next switch can be performed only after a minimum time, indicated by this object. This object is applicable only when sysCRdnRecMode=auto. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| sysCRdnHwSwFlip | 1.3.6.1.4.1.164.3.3.1.6.3.1.9 | ||
| HW or SW decision for Redundancy Flip. This object is applicable only for sysCRdnMode=singleSlotProtection. HW - decision is by I/O card SW - decision is by CL SW. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), hw(2), sw(3) | ||
| sysCRdnRowStatus | 1.3.6.1.4.1.164.3.3.1.6.3.1.10 | ||
| This parameter allows NMS to create/delete entries of this table. The only possible supported RowStatus vaules are active (1) and destroy (6). | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| sysCRdnOnline | 1.3.6.1.4.1.164.3.3.1.6.3.1.11 | ||
| Status - who is the Online (current) Redundancy Slot/Port. This object shows only the Online Slot/Port regarding the Redundancy. mdlSActivity or prtGenActiveStatus of the same Slot/Port may be Offline. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), primary(2), secondary(3) | ||
| sysCRdnSwitchingMode | 1.3.6.1.4.1.164.3.3.1.6.3.1.12 | ||
| This object defines which Self Healing Ring (SHR) SDH ring is used: Uni Directional or BiDirectional. The type of the ring is defined according to the direction of traffic flow under normal working conditions. In Bi Directional ring, the duplex traffic is on the same path and transverses the same set of nodes for both directions of transmission. In Uni Directional ring, the duplex traffic travels over opposite path (per direction) and all the node of the ring are involved. For Uni Directional SHR Protection Switching (Single Ended Switching) is controlled by one node of the SDH ring, and does not require a protocol. For Bi Directional SHR Protection Switching (Dual Ended switching) is controlled by some nodes of the ring and requires a protocol | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), biDirectional(2), uniDirectional(3) | ||
| sysCRdnFlipUponEvent | 1.3.6.1.4.1.164.3.3.1.6.3.1.13 | ||
| This object allows user to define if Flip to the other port will be performed (or not), for certain possible events. Each event is represented by a bit. The value of the object is a sum of 2**n, according to the bits having '1' value. '1' - means that Flip should occur due to this event. Bit 0 (LSB) = SD (Signal Degraded). For IPmux: Bit 0 (LSB) = TDM Line LOS/LOF. Bit 1 = Sequence Number. Bit 2 = Jitter Buffer errors. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnLosOrLofTime | 1.3.6.1.4.1.164.3.3.1.6.3.1.14 | ||
| This parameter determines how much time to wait before switching, after LOF or LOS are detected on the TDM Line. For Ipmux time is counted in msec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnEventsTimeWindow | 1.3.6.1.4.1.164.3.3.1.6.3.1.15 | ||
| This parameter determines the time window in which to count events to trigger protection switching. For Ipmux time is counted in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnSequenceNumberThreshold | 1.3.6.1.4.1.164.3.3.1.6.3.1.16 | ||
| This parameter determines the number of Sequence Number errors that should occur in the time window in order to cause switching. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnBufferErrorsThreshold | 1.3.6.1.4.1.164.3.3.1.6.3.1.17 | ||
| This parameter determines the number of Buffer undeflow/ overflow events occured in the time window that cause switching. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysCRdnBuffUnderrunTime | 1.3.6.1.4.1.164.3.3.1.6.3.1.18 | ||
| This parameter determines how much time to wait before switching, after jitter buffer underrun. Switching occurs if no frame arrives within that time. For Ipmux time is counted in msec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysDbase | 1.3.6.1.4.1.164.3.3.1.7 | ||
| OBJECT IDENTIFIER | |||
| sysDbaseSanityCheckCmd | 1.3.6.1.4.1.164.3.3.1.7.1 | ||
| Setting this attribute to on(3) will initiate the process of Sanity check on the TmpCnfg. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| sysDbaseDownloadCnfgIdxCmd | 1.3.6.1.4.1.164.3.3.1.7.2 | ||
| This attribute specifies the Id of the target RealCnfg to which the TmpCnfg should be transferred. Upon set command, the DACS agent will initiate the Sanity-Check process. If successful, the actual transfer will be performed. If there will be errors, the user will have to perform the command again after errors correction. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysDbaseUploadCnfgIdxCmd | 1.3.6.1.4.1.164.3.3.1.7.3 | ||
| This attribute specifies the Id of the source Cnfg to be loaded into the TmpCnfg. Upon set operation the actual transfer will be initiated. The operation is valid only on configuration numbers that do not exceed sysSMaxNoOfCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysDbaseFlipTable | 1.3.6.1.4.1.164.3.3.1.7.4 | ||
| Dbase Flip time and activation for every configuration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysDbaseFlipEntry | |||
| sysDbaseFlipEntry | 1.3.6.1.4.1.164.3.3.1.7.4.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysDbaseFlipEntry | |||
| sysDbaseFlipIdx | 1.3.6.1.4.1.164.3.3.1.7.4.1.1 | ||
| This attribute indicates the Idx of the Cnfg being the target Configuration. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysDbaseFlipTime | 1.3.6.1.4.1.164.3.3.1.7.4.1.2 | ||
| This attribute indicates the time (HH:MM) when this data base will start being used by the Tmp config. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysDbaseFlipActivation | 1.3.6.1.4.1.164.3.3.1.7.4.1.3 | ||
| This attribute indicates if the Dbase flip will be activated at the time specified for this configuration (enable) or not (disable). No more than one flip should be enabled for the same time. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| mdlDacsMux | 1.3.6.1.4.1.164.3.3.2 | ||
| OBJECT IDENTIFIER | |||
| mdlGen | 1.3.6.1.4.1.164.3.3.2.1 | ||
| OBJECT IDENTIFIER | |||
| mdlSTable | 1.3.6.1.4.1.164.3.3.2.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlSEntry | |||
| mdlSEntry | 1.3.6.1.4.1.164.3.3.2.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlSEntry | |||
| mdlSSltIdx | 1.3.6.1.4.1.164.3.3.2.1.1.1.1 | ||
| A unique number to identify a slot position in the DACS. The Kilomux should use enumerated values starting with kmx. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlSCardType | 1.3.6.1.4.1.164.3.3.2.1.1.1.2 | ||
| This attribute indicates the type of the card installed in the specific slot position. Only PS's are possible in the PS slots. Only CL's are possible in the CL slots. Only IO modules are possible in the IO slots. Kmux card type start with the letter k. LA card type start with the letters la. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), psAC(10), psDC(11), dCl(20), kCl(21), dcl2(22), dcl2Eth(23), kClEth(24), dcl3(25), dcl3Eth(26), d4T1(28), d8T1(29), dT1DSU(30), dT1CSU(31), dE1DSU(32), dE1LTU(33), dE1aDSU(34), dE1aLTU(35), dT1F(36), dE1F(37), d4E1(38), d8E1(39), dE1Hdsl(40), dT1Hdsl(41), dE1HdslS(42), dT1HdslS(43), d16gsdsl(44), d8sl(45), kML1(50), kML2(51), kML3(52), kML4(53), kML5(54), kML6(55), kML7(56), kML8(57), kML10(59), kMLF(60), kML10New(61), kML11RJ45(62), kML11FO(63), kLS1(70), kLS1New(71), kLS2(72), kTRE(80), kMBE(81), kMBENew(82), fLAN(83), kai(90), kdi(91), kdiCH(92), dHS2(100), d8U(101), d16U(102), kHS1(110), kHS2(111), kHSU1(112), kHSU2(113), kHS703(114), kVC1EM(130), kVC1FXO(131), kVC1FXS(132), kVC1MEM(133), kVC1MFXO(134), kVC1MFXS(135), kVC1MFXSW(136), kVC2EM(137), kVC2FXO(138), kVC2FXS(139), kVC2s1EM(140), kVC2s1FXO(141), kVC2s1FXS(142), kVC3EM(143), kVC3FXO(144), kVC3FXS(145), kVC3S0(146), kVF1EM(170), kVF1FXO(171), kVF1FXS(172), kVF3EM(173), kVF3FXO(174), kVF3FXS(175), kVF4EM(176), kVF4FXO(177), kVF4FXS(178), kVF4FXSW(179), kVF4S0(180), kVF5PbxE1(181), kVF5E1PbxSlave(182), kVF5PbxT1(183), kVF5T1PbxSlave(184), kVF5PbxE1New(185), kVF5E1PbxSlaveNew(186), kVF5PbxT1New(187), kVF5T1PbxSlaveNew(188), kVF4FXO3(189), kVF4FXS3(190), kVF4NS0(191), kVF6E1s16(192), kVF6E1s31(193), kVF6T1s12(194), kVF6T1s24(195), kVF8EM(196), kVF8FXO(197), kVF8FXS(198), dimV35(201), dimRS422(202), dimRS530(203), dimHssi(204), dimX21(205), dim10BaseT(206), dimE1(207), dim100(208), dt3G747(209), dt3(210), dt3f(211), de3(212), de3f(213), dstm1s1(214), dstm1s2(215), fSTM1(216), dstm1(217), dstm1R(218), f2stm1(219), laSUB(230), laVEM(231), laVFXO(232), laVFXS(233), laV11(234), laV24(235), laV35(236), laT1(237), laT1Vxx(238), laE1(239), laE1Vxx(240), laISDN(241), laVxx(242), laEth(243), laISDNwBU(244), laIsdnNT(245), laIsdnNTwBU(246), laIsdnTE(247), laFXSwBU(248), laFXSs(249), laFXSwBUs(250), laIsdnNTs(251), laIsdnNTwBUs(252), laIsdnTEs(253), laDp(254), laSdsl(255), laSdslDp(256), laAdslA(257), laAdslADp(258), laAdslB(259), laAdslBDp(260), laShdsl(261), laShdslDp(262), laT1b(263), laT1bDp(264), laIsdnTEwBU(265), laIsdnTEwBUs(266) | ||
| mdlSHwVer | 1.3.6.1.4.1.164.3.3.2.1.1.1.3 | ||
| This attribute indicates the Hardware version of the card installed in the specific slot position. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlSSwVer | 1.3.6.1.4.1.164.3.3.2.1.1.1.4 | ||
| This attribute indicates the Software version of the card installed in the specific slot position. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlSAlarmStatus | 1.3.6.1.4.1.164.3.3.2.1.1.1.5 | ||
| Indicates the current alarm state only for card level. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), major(3), minor(4), event(5), warning(6), critical(7) | ||
| mdlSAlarmStatusAll | 1.3.6.1.4.1.164.3.3.2.1.1.1.6 | ||
| Indicates the current card alarm state including the lower level: card, port. This object will be set to: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), major(3), minor(4), event(5), warning(6), critical(7) | ||
| mdlSTestStatus | 1.3.6.1.4.1.164.3.3.2.1.1.1.7 | ||
| This attribute will be on(3) when there is at least one test running on a port of the module; otherwise the value will be off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSHwStatus | 1.3.6.1.4.1.164.3.3.2.1.1.1.8 | ||
| This attribute will be fail(2) when a HW FAIL exists on this module (discovered by periodic self test); otherwise the value will be ok(3). | |||
| OBJECT-TYPE | |||
| INTEGER | fail(2), ok(3) | ||
| mdlSActivity | 1.3.6.1.4.1.164.3.3.2.1.1.1.9 | ||
| notApplicable - when the slot is empty (no module) offline(1) - when the module is not active (redundant) online (2) - when the module is active . | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), offline(2), online(3) | ||
| mdlSAlrClearCmd | 1.3.6.1.4.1.164.3.3.2.1.1.1.10 | ||
| Setting this attribute to ON, will enforce a clear operation on the card level alarms . Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSAlrClearAllCmd | 1.3.6.1.4.1.164.3.3.2.1.1.1.11 | ||
| Setting this attribute to ON, will enforce a clear operation on card and port level alarms . Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSAlrMaskAll | 1.3.6.1.4.1.164.3.3.2.1.1.1.12 | ||
| on(3) - will cause masking of all the card level alarms. These alarms will not be sent to NMS and will not be taken into account for Alarms Status. off(2) - will unmask all card level alarms except those masked via the mdlAlrMaskTable. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSCmd | 1.3.6.1.4.1.164.3.3.2.1.1.1.13 | ||
| General object for any special command at card level. 0=NotApplicable, for cards that don't support this object. For KML.10(ISDN) card of KM-2100, the object will indicate Manual Call Command in Switch mode. It is applicable only when for KML.10, prtIsdnSwitchMode=manual. KML.10 valid values: '1' = noOp, will be used by agents that do not support this feature or object (old KM agents) '2' = off, Set call command mode to disconnect state. Disconnects the call. '3' = on, Set call command mode to connect state. Connects the call. For DXC IO cards, the object will be used for IO Card Reset HW command: '2' = off, this will be always the Get value for these cards. '3' = on, this is the Set command used to Reset the IO card. Upon completing the operation, the value will automatically change to off(2), by Agent. For Slots that are NOT IO Slots and for empty IO Slots, the Get value will be always '0' (NotApplicable). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlSReset | 1.3.6.1.4.1.164.3.3.2.1.1.1.14 | ||
| Reset action to be performed on the module. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSRebuildFrame | 1.3.6.1.4.1.164.3.3.2.1.1.1.15 | ||
| Applicable only for KiloMux Main Link cards only. '2' = off, this will be always the Get value. '3' = on, this is the Set command used to Rebuild the Frame. Upon completing the operation, the value will automatically change to off(2), by Agent. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| mdlCTable | 1.3.6.1.4.1.164.3.3.2.1.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlCEntry | |||
| mdlCEntry | 1.3.6.1.4.1.164.3.3.2.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlCEntry | |||
| mdlCConfigIdx | 1.3.6.1.4.1.164.3.3.2.1.2.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| mdlCSlotIdx | 1.3.6.1.4.1.164.3.3.2.1.2.1.2 | ||
| This object indicates a unique number of the slot position in which the module is inserted. The Kilomux should use enumerated values starting with kmx. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlCProgCardType | 1.3.6.1.4.1.164.3.3.2.1.2.1.3 | ||
| This object indicates the card type assigned to the specific slot in the common configuration. This object is identical for all the configurations (1..255). Only the TmpCnf(255) might have a different value. The write operation is valid only for the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), psAC(10), psDC(11), dCl(20), kCl(21), dcl2(22), dcl2Eth(23), kClEth(24), dcl3(25), dcl3Eth(26), d4T1(28), d8T1(29), dT1DSU(30), dT1CSU(31), dE1DSU(32), dE1LTU(33), dE1aDSU(34), dE1aLTU(35), dT1F(36), dE1F(37), d4E1(38), d8E1(39), dE1Hdsl(40), dT1Hdsl(41), dE1HdslS(42), dT1HdslS(43), d16gsdsl(44), d8sl(45), kML1(50), kML2(51), kML3(52), kML4(53), kML5(54), kML6(55), kML7(56), kML8(57), kML10(59), kMLF(60), kML10New(61), kML11RJ45(62), kML11FO(63), kLS1(70), kLS1New(71), kLS2(72), kTRE(80), kMBE(81), kMBENew(82), fLAN(83), kai(90), kdi(91), kdiCH(92), dHS2(100), d8U(101), d16U(102), kHS1(110), kHS2(111), kHSU1(112), kHSU2(113), kHS703(114), kVC1EM(130), kVC1FXO(131), kVC1FXS(132), kVC1MEM(133), kVC1MFXO(134), kVC1MFXS(135), kVC1MFXSW(136), kVC2EM(137), kVC2FXO(138), kVC2FXS(139), kVC2s1EM(140), kVC2s1FXO(141), kVC2s1FXS(142), kVC3EM(143), kVC3FXO(144), kVC3FXS(145), kVC3S0(146), kVF1EM(170), kVF1FXO(171), kVF1FXS(172), kVF3EM(173), kVF3FXO(174), kVF3FXS(175), kVF4EM(176), kVF4FXO(177), kVF4FXS(178), kVF4FXSW(179), kVF4S0(180), kVF5PbxE1(181), kVF5E1PbxSlave(182), kVF5PbxT1(183), kVF5T1PbxSlave(184), kVF5PbxE1New(185), kVF5E1PbxSlaveNew(186), kVF5PbxT1New(187), kVF5T1PbxSlaveNew(188), kVF4FXO3(189), kVF4FXS3(190), kVF4NS0(191), kVF6E1s16(192), kVF6E1s31(193), kVF6T1s12(194), kVF6T1s24(195), kVF8EM(196), kVF8FXO(197), kVF8FXS(198), dimV35(201), dimRS422(202), dimRS530(203), dimHssi(204), dimX21(205), dim10BaseT(206), dimE1(207), dim100(208), dt3G747(209), dt3(210), dt3f(211), de3(212), de3f(213), dstm1s1(214), dstm1s2(215), fstm1(216), dstm1(217), dstm1R(218), f2stm1(219) | ||
| mdlCNoOfExtPrt | 1.3.6.1.4.1.164.3.3.2.1.2.1.4 | ||
| Number of external ports in the programmed module of the specific slot position | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCNoOfIntPrt | 1.3.6.1.4.1.164.3.3.2.1.2.1.5 | ||
| Number of internal ports in the programmed module of the specific slot position. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCParam | 1.3.6.1.4.1.164.3.3.2.1.2.1.6 | ||
| General configuration object at card level (per configuration). NotApplicable=0, for cards that don't support this object. For D8U and D16U cards of DXC, the object will indicate the port on which BERT will be performed. The port can be one of the external ports, any of its associated B1, B2, D ports or no port of the card (None=0). For port indexes see DXC R6 spec. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlr | 1.3.6.1.4.1.164.3.3.2.1.3 | ||
| OBJECT IDENTIFIER | |||
| mdlAlrTable | 1.3.6.1.4.1.164.3.3.2.1.3.1 | ||
| The list of card alarms. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlAlrEntry | |||
| mdlAlrEntry | 1.3.6.1.4.1.164.3.3.2.1.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlAlrEntry | |||
| mdlAlrIdx | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.1 | ||
| A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlrSltIdx | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.2 | ||
| This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlAlrCode | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.3 | ||
| This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlrState | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.4 | ||
| This object indicates the card alarm severity. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| mdlAlarmMask | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.5 | ||
| Alarm Mask is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlAlarmInvert | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.6 | ||
| Alarm Invert is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlAlarmOnOff | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.7 | ||
| Alarm state is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlAlarmCounter | 1.3.6.1.4.1.164.3.3.2.1.3.1.1.8 | ||
| A counter - how many times the alarm occured (ON) since last clear operation or since last Reset. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlAlrMaskTable | 1.3.6.1.4.1.164.3.3.2.1.3.2 | ||
| The list of card masked alarms. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlAlrMaskEntry | |||
| mdlAlrMaskEntry | 1.3.6.1.4.1.164.3.3.2.1.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlAlrMaskEntry | |||
| mdlAlrMaskSltIdx | 1.3.6.1.4.1.164.3.3.2.1.3.2.1.1 | ||
| This attribute indicates the desired slot position. The Kilomux should use enumerated values starting with kmx. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlAlrMask | 1.3.6.1.4.1.164.3.3.2.1.3.2.1.2 | ||
| This object is a mask that indicates which card level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the card level will be 0. This object is applicable only when mdlSAlrMaskAll=off (otherwise all card alarms are masked). Example: When Alarm having the code 8 is masked, the value of this object will be 100 (hex). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8..10) | ||
| mdlCl | 1.3.6.1.4.1.164.3.3.2.2 | ||
| OBJECT IDENTIFIER | |||
| mdlClTable | 1.3.6.1.4.1.164.3.3.2.2.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlClEntry | |||
| mdlClEntry | 1.3.6.1.4.1.164.3.3.2.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlClEntry | |||
| mdlClIdx | 1.3.6.1.4.1.164.3.3.2.2.1.1.1 | ||
| This object indicates the Cl slot referred. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4) | ||
| mdlClSwchStatus | 1.3.6.1.4.1.164.3.3.2.2.1.1.2 | ||
| This object indicates the status of the switches on the referred DCL card. Each switch is represented by a bit. The status is a sum of 2**n, according to the bits. There are 4 switches: bit 0 SP-PAR (LSB) '1' - Default parameters bit 1 PSWRD '1' - Password=default '0' - Password=user selected bit 2 DB-INIT '1' - DB initiated with default '0' - DB initiated with NVRAM contents bit 3 PC-SP (MSB) '1' - Management by terminal only '0' - Management by NMS Example: If SP-PAR and PSWRD bits are set ('1'), the value will be 3 (2**1 + 2**0). When the status of the switches is unknown, the value of this object will be 255. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlClLastFlipDate | 1.3.6.1.4.1.164.3.3.2.2.1.1.3 | ||
| Date when last flip occured. The format would be as specified by the sysSDateFormat. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlClLastFlipTime | 1.3.6.1.4.1.164.3.3.2.2.1.1.4 | ||
| Time when last flip occured. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlClLastFlipCause | 1.3.6.1.4.1.164.3.3.2.2.1.1.5 | ||
| The cause of last flip. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| mdlPs | 1.3.6.1.4.1.164.3.3.2.3 | ||
| OBJECT IDENTIFIER | |||
| mdlPsTable | 1.3.6.1.4.1.164.3.3.2.3.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlPsEntry | |||
| mdlPsEntry | 1.3.6.1.4.1.164.3.3.2.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlPsEntry | |||
| mdlPsIdx | 1.3.6.1.4.1.164.3.3.2.3.1.1.1 | ||
| This object indicates the PS card referred. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2) | ||
| mdlPsStatus | 1.3.6.1.4.1.164.3.3.2.3.1.1.2 | ||
| This object indicates the status of the PS card. | |||
| OBJECT-TYPE | |||
| INTEGER | notActive(1), active(2) | ||
| mdlPsTestResult | 1.3.6.1.4.1.164.3.3.2.3.1.1.3 | ||
| This object indicates the result of the PS card test. ok (1) - the test passed successfully. f12V (2) - 12V FAIL was detected f5V (3) - 5V FAIL was detected. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), f12V(2), f5V(3) | ||
| prtDacsMux | 1.3.6.1.4.1.164.3.3.3 | ||
| OBJECT IDENTIFIER | |||
| prtGen | 1.3.6.1.4.1.164.3.3.3.1 | ||
| OBJECT IDENTIFIER | |||
| prtGenParamTable | 1.3.6.1.4.1.164.3.3.3.1.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtGenEntry | |||
| prtGenEntry | 1.3.6.1.4.1.164.3.3.3.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtGenEntry | |||
| prtGenPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.1.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenSlt | 1.3.6.1.4.1.164.3.3.3.1.1.1.2 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. The Kilomux should use the enumerated starting with kmx. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), standAlone(255) | ||
| prtGenExtInt | 1.3.6.1.4.1.164.3.3.3.1.1.1.3 | ||
| This attribute describes the type of the designated port. Exteral port is a port with a physical connector. Internal port might be of two types, one is a composite port which collects data of a few external ports into a common bandwidth (usually routed trough DS1 link); the other type is internal ports which get only part of external port data (usually a few DS0's). In the Kilomux-2100, the internal(3) value is used for composite channels or sub-channels of an ISDN Ch. | |||
| OBJECT-TYPE | |||
| INTEGER | external(2), internal(3) | ||
| prtGenIfIndex | 1.3.6.1.4.1.164.3.3.3.1.1.1.4 | ||
| This attribute indicates the unique interface number assigned to the port. The specific interface of this attribute is the same as the interface identified by the value of ifindex in MIB-II.If there is no interface for the specific prtIdx, the value will be '7fffffff'h. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenActiveStatus | 1.3.6.1.4.1.164.3.3.3.1.1.1.5 | ||
| This attribute describes the activity status of the port. unknown(1) indicates that the information is not supported. notUsed(2) indicates that the port is not connected according to the active config. offLine(3) indicates that the port is down (not working) due to any problem. onLine (4) indicates that the port is up (working) offLineRedundancy(5) indicates that the port is down because it is a redundant port. onLineRedundancy (6) indicates that this is a redundant port which is up and works as the active link. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), notUsed(2), offLine(3), onLine(4), offLineRedundancy(5), onLineRedundancy(6) | ||
| prtGenAlrStatus | 1.3.6.1.4.1.164.3.3.3.1.1.1.6 | ||
| Indicates the alarm state at port (ch) agent level. This object will be: - critical(7): when there is at least one active (ON) critical alarm . - major (3): when there is no active critical alarm, but there is at least one active (ON) major alarm . - minor (4): when there is no active major or critical alarm, but there is at least one active minor alarm. - warning (6): when there is no active major, critical or minor alarm, but there is at least one active warning alarm. - event (5): when there is no active alarm of another type, but there is at least one active event alarm. - off(2): when there is no active (ON) alarm (since last clear operation). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), major(3), minor(4), event(5), warning(6), critical(7) | ||
| prtGenTestStatus | 1.3.6.1.4.1.164.3.3.3.1.1.1.7 | ||
| This attribute will be on(3) when there is at least one test in progress (running) on the port; otherwise the value will be off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtGenTestMask | 1.3.6.1.4.1.164.3.3.3.1.1.1.8 | ||
| This is a mask which indicates which tests from the 'prtGenTestCmd' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTestCmd | 1.3.6.1.4.1.164.3.3.3.1.1.1.9 | ||
| Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMask). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the requested value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTestRunning | 1.3.6.1.4.1.164.3.3.3.1.1.1.10 | ||
| This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 e.g : If the return value is 3 -> 0000000000000011 -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only! | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenType | 1.3.6.1.4.1.164.3.3.3.1.1.1.11 | ||
| This object describes the type of the selected port. idsl - applicable for external ports of HS-U cards (of DXC) when interface is LT-1. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), t1(2), e1(3), hs(4), t1Csu(5), t1Dsu(6), e1Ltu(7), e1Dsu(8), hdsl(9), sp(10), t1F(11), e1F(12), dim(13), isdn(14), t3(15), e3(16), t3f(17), e3f(18), idsl(19), stm1(20), vc4(21), vc12(22), msdsl(23), vc11(24), vc3(25), soh(26), eth(27), shdsl(28), other(255) | ||
| prtGenInterfaceType | 1.3.6.1.4.1.164.3.3.3.1.1.1.12 | ||
| This attribute indicates a unique HW interface type of the selected port. Examples: - for T1 cards: DSU, CSU - for E1 cards: DSU, LTU - for HS cards: v35, rs422, x21 etc... | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtGenAlrClearCmd | 1.3.6.1.4.1.164.3.3.3.1.1.1.13 | ||
| Setting this attribute to ON, will enforce a clear operation on the port level alarms . Upon completion, the value will automatically change to off(2). noOp - will be used by agents that do not support this feature or object. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), off(2), on(3) | ||
| prtGenAlrMaskAll | 1.3.6.1.4.1.164.3.3.3.1.1.1.14 | ||
| on(3) - will mask all the alarms of the selected port off(2)- will unmask all alarms of the selected port except the ones selected by the prtAlrMaskTable. noOp - will be used by agents that do not support this feature or object. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), off(2), on(3) | ||
| prtGenParamStatus | 1.3.6.1.4.1.164.3.3.3.1.1.1.15 | ||
| This object indicates Status of parameters specific to the selected port. - For a port that has no special status or is supported by prtSExHsfStatTable - 1 Octet: 00hex - For HS cards (Dxc cards) - 1 octet: Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 0 and 1 indicates RTS control signal state: Bit 1: '1'=active ; '0'=notActive Bit 0 (LSB): '1'=unknown ; '0'=NA - For HS-U/1 external port (MP card, used in FCD-M) - 1 Octet: Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For VC-6, VC-12, VC-12/6 external ports - 1 Octet : Bit 7 (MSB)..Bit 2 = 0 (NA) Bit 1: Tx Signaling '1'=On ; '0'=Off Bit 0 (LSB): Rx Signaling '1'=On ; '0'=Off - For VC-2/R2(FXS) external ports - 1 Octet : Bit - 7 6 5 4 3 2 1 0 |_| |_________| Call Call State Direction Bit 7 (MSB) and Bit 6 : Call Direction 00 - Incoming 01 - Outgoing Bit 5..Bit 0: Call State 000000 - Idle 000001 - Seized 000010 - Both-Way Conflict 000011 - Seizure Ack 000100 - Answered 000101 - Clear Backward 000110 - Clear Forward 000111 - Blocked 001000 - Fault 001001 - Fault 3 001010 - Fault 4 001011 - Fault 5 001100 - Fault 6 001101 - Fault 7 - For ML-20 external port - 3 Octets : - 1 MS Octet will represent the Real Rate used: Bit - 7 6 5 4 3 2 1 0 |___| |_______| spare Rate Valid values: 0..31, meaning 0..31x64Kbps Invalid values: 32..255. - 2 LS Octets will represent the Status of 7 Control Signals: Signal - --- CTS DSR DCD RJ TM DTR RTS Bit - 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Octet - 2 3 (LS) '---' will always have the value 00 Rest of the Signals (2 bits each) can have the following values: 00=NA ; 01=Unused ; 10=Off ; 11=On - For ML-H/E1, ML-H/1/E1, ML-H/S/E1 internal port - 1 Octet Bit - 7 6 5 4 3 2 1 0 |___________| spare Mode of Operation Mode of Operation: '1'=Central ; '0'=Remote - For KM2100, KVF.5 cards - indicates the status of A and B signaling for each internal channel. 1 Octet: Bit - 7 6 5 4 3 2 1 0 |_____| |_| |_| spare B A Bit 0 (LSB) and Bit 1 : A status Bit 2 and Bit 3 : B status 00 - Off 01 - On 11 - Unknown - For FCD-W, NETWORK and USER ports - 1 Octet Status of Control Signals: '1'=On ; '0'=Off or when not applicable Bit - 7 6 5 4 3 2 1 0 Bit 7 (MSB) - Signal Loss (applicable only for G.703 interface) Bit 6 - CONTROL (applicable only for X.21 interface) Bit 5 - INDICATION (applicable only for X.21 interface) Bit 4 - DSR (applicable only for V.35 interface) Bit 3 - RTS (applicable only for V.35 interface) Bit 2 - CTS (applicable only for V.35 interface) Bit 1 - DTR (applicable only for V.35 interface) Bit 0 - DCD (applicable only for V.35 interface) - For DXC R6 , D8U, D16U External ports - 1 Octet Bit 7 6 5 4 3 2 1 0 LSB |________| |__| |__| spare modem sync modem: 00 = other sync: 00 = not sync 01 = unknown 01 = sync 10 = ASMi-31/2 10 = reserved 11 = reserved 11 = reserved - For DXC DE1-HDSL, DT1-HDSL, D16GSDSL, D8SL External ports - 2 Octets MSB octet: far-end modem channel interface LSB octet: Sub Link existence (Y/N), far-end modem type, synchronization with far-end modem MSB octet: 0000 0000 = no interface 0000 0001 = db15 (X21) 0000 0010 = IR-IP 0000 0011 = IR-ETH-Q 0000 0100 = V35 0000 0101 = ETH-RJ45 0000 0110 = G703 0000 0111 = db25 (RS530) 0000 1000 = ETH-BNC 0000 1001 = E1(Balanced) 0000 1010 = E1(Unbalanced) Rest of the combinations: reserved LSB octet: Bit 7 6 5 4 3 2 1 0 LSB | |___________| |__| SL modem sync or Box material SL: modem: 00000 = other sync: 00 = not sync 0=not exist 00001 = unknown 01 = sync 1=exists 00010 = ASMi-31/2 10 = reserved 00011 = HCD-E1 11 = reserved Box material 00100 = HTU-E1 (for D8SL card): 00101 = HTU-2 0=metal 00110 = ASMi-52 SA/2W/Slave 1=plastic 00111 = ASMi-52 SA/2W/Master 01000 = ASMi-52/CQ card of LRS-24 01001 = ASMi-52/CD card of LRS-24 01010 = D16GSDSL card of DXC-3000 01011 = LRS-52 01100 = FCD 01110 = D8GSDSL card of DXC-3000 Rest = reserved | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtGenRdnStatus | 1.3.6.1.4.1.164.3.3.3.1.1.1.16 | ||
| This object indicates if this port is part of a redundant pair and in this case, if it is On or Off. none(1) - No redundancy or Not Applicable off (2) - the port is part of a redundant pair and it is Off from Redundancy point of view (not the port used). on (3) - the port is part of a redundant pair and it is On from Redundancy point of view (it is the port used). | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), off(2), on(3) | ||
| prtGenTestMaskXP | 1.3.6.1.4.1.164.3.3.3.1.1.1.17 | ||
| This is an Expanded test mask of the prtGenTestMask object. The prtGenTestMask object reached its maximum, being an Integer with 31 bits. This object indicates which tests from the 'prtGenTestCmdXP' list are allowed for the selected port. If a specific test is allowed, its respective bit will be SET in the mask : TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the allowed tests are : local-loop remote-loop | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtGenTestCmdXP | 1.3.6.1.4.1.164.3.3.3.1.1.1.18 | ||
| This is an Expanded test command of the prtGenTestCmd object. The prtGenTestCmd object reached its maximum, being an Integer with 31 bits. Setting this object to a value as detailed furter on (except 0) will initiate a test on the specific port, if the operation is allowed (according to TestMaskXP). If the operation is not allowed, the mux will ignore the operation. The test/s requested will be set according to the respective bit: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 inband 5 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 e.g : If the requested value is 00000003 hex -> Bits 1 & 2 are set -> the requested tests are : local-loop remote-loop Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port; it will NOT stop the tests initiated by the system. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtGenTestRunningXP | 1.3.6.1.4.1.164.3.3.3.1.1.1.19 | ||
| This is an Expanded object of the prtGenTestRunning object. The prtGenTestRunning object reached its maximum, being an Integer with 31 bits. This object indicates which tests are running currently on the selected port (initiated by user and/or by the system). If a specific test is currently running on the port, its respective bit will be SET: TEST BIT ----------- --- localLoop 1 =LSB remoteLoop 2 bert 3 plb 4 llb 5 txInband 6 rxInband 7 prbs 8 loop2-v54 (RLB) 9 loop3-v54 (LLB) 10 DDS DSU loop 11 DDS CSU loop 12 Tone injection 13 Tx-plb 14 Tx-llb 15 DTE loop (HSSI) 16 Local DTE loop (HSSI)17 Local Line loop (HSSI)18 Remote Line loop (HSSI)19 HDSL-Tx-Inband 20 HDSL-Rx-Inband 21 Monitor 22 (test port) User Line Loopback 23 Network Line Loopback 24 Rem-Loop-on-Rem-Unit 25 LBBD 26 LB1 27 LB2 28 BERT-on-Rem-Unit 29 TS Remote Loop 30 LLB-on-Rem-Unit 31 Downstream-AIS 32 Upstream-AIS 33 Send-RDI 34 e.g : If the return value is 00000003 hex -> Bits 1 & 2 are set -> the running tests are : local-loop remote-loop llb (Bit 5) - can be initiated by system only! | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtGenTestDurationTable | 1.3.6.1.4.1.164.3.3.3.1.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtGenTestDurationEntry | |||
| prtGenTestDurationEntry | 1.3.6.1.4.1.164.3.3.3.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtGenTestDurationEntry | |||
| prtGenTestPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.2.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTestIdx | 1.3.6.1.4.1.164.3.3.3.1.2.1.2 | ||
| This attribute indicates the test, the duration refers. | |||
| OBJECT-TYPE | |||
| INTEGER | localLoop(1), remoteLoop(2), bert(3), plb(4), rlb(5), llb(6), toneInjection(7), txInband(8), rxInband(9), remLoopOnRemUnit(10), bertOnRemUnit(11), llbOnRemUnit(12), txPlb(14), txLlb(15), dteLoop(16), hdslTxInband(20), hdslRxInband(21), monitor(22), userLineLoopback(23), lbbd(26), lb1(27), lb2(28), tsRemoteLoop(30), downstreamAis(32), upstreamAis(33), sendRdi(34) | ||
| prtGenTestDuration | 1.3.6.1.4.1.164.3.3.3.1.2.1.3 | ||
| This attribute indicates the maximum duration of executing a test on the specific port. This entry applies to the specified test . The resolution will be a minute, and the maximum duration is limited to 30 minutes . A zero value specifies no time limitation. When the test isn't active the agent initiates this object to 2 min. when the duration is needed and to 0 if it's not required. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTsTable | 1.3.6.1.4.1.164.3.3.3.1.3 | ||
| The write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch),exept some products which enable direct writing to the ActiveCnfg. This is written in the respective product's spec. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtGenTsEntry | |||
| prtGenTsEntry | 1.3.6.1.4.1.164.3.3.3.1.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtGenTsEntry | |||
| prtGenTsCnfgIdx | 1.3.6.1.4.1.164.3.3.3.1.3.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtGenTsPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.3.1.2 | ||
| This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTsIdx | 1.3.6.1.4.1.164.3.3.3.1.3.1.3 | ||
| This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 or HS Card . In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTsType | 1.3.6.1.4.1.164.3.3.3.1.3.1.4 | ||
| The type of Timeslot. If the source or destination port is an HS port,'TS Type' must be 'data'. nc - means that this TimeSlot is not connected. voice, data, vcMP - also mean that this TS is connected. mng - means that this TS is dedicated to Management (not connected to another port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), voice(2), data(3), vcMP(4), nc(5), mng(6) | ||
| prtGenTsIConPrt | 1.3.6.1.4.1.164.3.3.3.1.3.1.5 | ||
| This attribute indicates the internally (In Mux) connected port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside ports will be for example, the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) for a stand-alone unit, the IO slot will be considered 1. - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * noConnection - will be indicated as 10 for DXC and FCD-E1/T1. - will be indicated as 100 for FCD-E1/I and SMODs. * Split TS (same TS is Split to several ports) - 11. * notApplicable- will be indicated as 100 for LRS IMODs. All HS port's timeslots must have the same destination port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtGenTsIConTs | 1.3.6.1.4.1.164.3.3.3.1.3.1.6 | ||
| This attribute indicates a unique time slot position. The valid time slots are 1..25 for T1 Card (25=Fbit) 0..31 for E1 (or HS) Card. In G732S-E1 lines time slot 16 is not valid for data, it is dedicated for multiframe synchronization bits and voice signaling. * For DXC: All HS port's timeslots must start with Timeslot no.1 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlr | 1.3.6.1.4.1.164.3.3.3.1.4 | ||
| OBJECT IDENTIFIER | |||
| prtSAlarmTable | 1.3.6.1.4.1.164.3.3.3.1.4.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSAlarmEntry | |||
| prtSAlarmEntry | 1.3.6.1.4.1.164.3.3.3.1.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtSAlarmEntry | |||
| prtSAlarmIdx | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.1 | ||
| A unique number to identify an entry in the alarm status table. Users should use the get next function to read this table because the indexes are not consecutive. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlarmPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.2 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlarmCode | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.3 | ||
| This object indicates a code related to a specific alarm description. The list of codes and their related descriptions will be sent to NMS request (for display purpose) by alrGenTable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSAlarmState | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.4 | ||
| This object indicates the port alarm severity. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| prtSAlarmMask | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.5 | ||
| Alarm Mask is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSAlarmInvert | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.6 | ||
| Alarm Invert is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSAlarmOnOff | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.7 | ||
| Alarm state is : on/off. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtSAlarmCounter | 1.3.6.1.4.1.164.3.3.3.1.4.1.1.8 | ||
| A counter - how many times the alarm occured (ON) since last clear operation or since last Reset. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlrMaskTable | 1.3.6.1.4.1.164.3.3.3.1.4.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtAlrMaskEntry | |||
| prtAlrMaskEntry | 1.3.6.1.4.1.164.3.3.3.1.4.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtAlrMaskEntry | |||
| prtAlrMaskPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.4.2.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtAlrMask | 1.3.6.1.4.1.164.3.3.3.1.4.2.1.2 | ||
| This object is a mask that indicates which port level alarms are masked. The masked alarms (their bit is set to '1') are neither sent to the manager, nor taken into account for alarm status and LEDs. Bit no. = Alarm code The bits that do not belong to the port level will be 0. This object is applicable only when prtGenAlrMaskAll=off (otherwise all port alarms are masked). Example: When Alarms having the codes 31 and 40 are masked, the value of this object will be 10080000000 (hex). | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(8) | ||
| prtBertTable | 1.3.6.1.4.1.164.3.3.3.1.5 | ||
| This table includes the BERT parameters, counters and commands. The configurable parameters: - prtBertPattern - prtBertInjectRate - prtBertTs are not Set per configuration (same for all Configurations) but start being applied by the Agent only upon successful Update/Download operation. Therefore, Set will enter the values to the Temporary Configuration of the agent, while Get will get the values of the Active Configuration. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtBertEntry | |||
| prtBertEntry | 1.3.6.1.4.1.164.3.3.3.1.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtBertEntry | |||
| prtBertPrtIdx | 1.3.6.1.4.1.164.3.3.3.1.5.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside/external, inside/internal. In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the MP : - first two digits will be: (IO slot number+10) - last one/two digits will be according to the external port number within the card: exPrt1 -> 1 exPrt2 -> 3 exPrt3 -> 5 exPrt4 -> 7 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertPattern | 1.3.6.1.4.1.164.3.3.3.1.5.1.2 | ||
| This object indicates the pattern of the BERT. p2Exxm1 = 2Exx-1. pxx = pattern xx. This object is the same for all configurations. notApplicable - when this object is not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | p2E3m1(1), p2E4m1(2), p2E5m1(3), p2E6m1(4), p2E7m1(5), p511(6), p2E10m1(7), p2047(8), p2E15m1(9), p2E17m1(10), p2E18m1(11), p2E20m1(12), qrss(13), p2E21m1(14), p2E22m1(15), p2E23m1(16), p2E25m1(17), p2E28m1(18), p2E29m1(19), p2E31m1(20), p2E32m1(21), rj011(22), p63(23), p1M7S(24), p1S7M(25), alternate(26), mark(27), space(28), notApplicable(255) | ||
| prtBertInjectRate | 1.3.6.1.4.1.164.3.3.3.1.5.1.3 | ||
| This object indicates the error rate injection of the BERT. r10Emx = 10E-x This object is the same for all configurations. single - single error injection. notApplicable - when this object is not supported. | |||
| OBJECT-TYPE | |||
| INTEGER | noError(1), r10Em1(2), r10Em2(3), r10Em3(4), r10Em4(5), r10Em5(6), r10Em6(7), r10Em7(8), single(9), notApplicable(255) | ||
| prtBertInjectErrRateCmd | 1.3.6.1.4.1.164.3.3.3.1.5.1.4 | ||
| This object controls activation/deactivation of the Error Rate Injection during BERT. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtBertInjectSingleErrCmd | 1.3.6.1.4.1.164.3.3.3.1.5.1.5 | ||
| This object enables to initiate a Single Error Injection during BERT (on). Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtBertRunTime | 1.3.6.1.4.1.164.3.3.3.1.5.1.6 | ||
| This object indicates how much time (seconds) passed since BERT started to run. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertESs | 1.3.6.1.4.1.164.3.3.3.1.5.1.7 | ||
| How many Errored Seconds were detected since BERT started to run. Counter for Kmux and MP. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertSyncLoss | 1.3.6.1.4.1.164.3.3.3.1.5.1.8 | ||
| How many times Sync Loss was detected since BERT started to run. For some products: number of seconds in which Sync Loss occured since BERT started to run. See product specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertErrorBits | 1.3.6.1.4.1.164.3.3.3.1.5.1.9 | ||
| How many Error Bits were detected since BERT started to run. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertClearCounters | 1.3.6.1.4.1.164.3.3.3.1.5.1.10 | ||
| Setting this object to ON, will enforce a clear operation of some BERT Counters. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtBertSyncStatus | 1.3.6.1.4.1.164.3.3.3.1.5.1.11 | ||
| Sync Status while BERT runs. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), syncLoss(2), sync(3) | ||
| prtBertTs | 1.3.6.1.4.1.164.3.3.3.1.5.1.12 | ||
| This object indicates on which TSs of the selected port, BERT should be applied. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - BERT should be applied on this TS. For a T1 port, the valid raised bits ('1') are: 1..25. For an E1 port, the valid raised bits ('1') are: 1..31. Agents that do not support this feature will send SIZE 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtBertResult | 1.3.6.1.4.1.164.3.3.3.1.5.1.13 | ||
| This object indicates Result of BERT for the selected port (number of error bits divided to the total number of data bits.) Applicable only if BERT is running on this port Agents that do not support this feature will send SIZE 0. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtMonTable | 1.3.6.1.4.1.164.3.3.3.1.6 | ||
| For DXC, the write operation into the Table's Objects is valid only for the TmpCnfg entry (Scratch). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMonEntry | |||
| prtMonEntry | 1.3.6.1.4.1.164.3.3.3.1.6.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtMonEntry | |||
| prtMonCnfgIdx | 1.3.6.1.4.1.164.3.3.3.1.6.1.1 | ||
| This object indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. For products that do not support configurations, 1 will be always used. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtMonitoringIdx | 1.3.6.1.4.1.164.3.3.3.1.6.1.2 | ||
| This object indicates the Monitoring Port Index. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For Optimux-T3: 255 (Not Applicable) will be always used. The Monitoring port is always the Station Clock (not considered an interface). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMonitoringEnable | 1.3.6.1.4.1.164.3.3.3.1.6.1.3 | ||
| This object indicates if the prtMonitoringIdx is configured as a monitoring port or not. disabled = the port is NOT configured to monitor. Setting this object to this value will cause reset (to 0) of the prtMonitoringTSs and prtMonitoredTSs objects. enabled = the port IS configured to monitor. For Optimux-T3: always enabled (RO supported). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtMonitoringTSs | 1.3.6.1.4.1.164.3.3.3.1.6.1.4 | ||
| This object indicates which TSs of the Monitoring port, the test equipment should monitor. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtMonitoredPort | 1.3.6.1.4.1.164.3.3.3.1.6.1.5 | ||
| This object indicates the MONITORED Port Index that the Monitoring port monitors. For DXC: The valid port number depends on the IO slot no., the installed card type and the port type: external, internal. * The external ports will according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The internal ports will be according to the convention (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . * 100 - no port monitored For Optimux-T3: The valid channels are: 0 = no Ch monitored 1..21 or 1..28 (=CH1..CH21 or CH1..CH28) according to product's configuration. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMonitoredTSs | 1.3.6.1.4.1.164.3.3.3.1.6.1.6 | ||
| This object indicates which TSs of the Monitored port, should be monitored. Each Bit of the Octet represents a TS: 31 ......0 MSB LSB Bit 0 will not be used. If the bit value is '1' - this TS should be monitored. For a T1 port, the valid raised bits ('1') are: 1..24. For an E1 port, the valid raised bits ('1') are: 1..31. Default: all bits='0' Agents that do not support this feature will send SIZE 0. This object can be Set as described only if prtMonitoringEnable=enabled. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtCfgParam | 1.3.6.1.4.1.164.3.3.3.1.7 | ||
| OBJECT IDENTIFIER | |||
| prtCfgParamTable | 1.3.6.1.4.1.164.3.3.3.1.7.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. Parameters for the channels of the KMUX Cards: KMBE/New, KVF.6 family. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtCfgParamEntry | |||
| prtCfgParamEntry | 1.3.6.1.4.1.164.3.3.3.1.7.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtCfgParamEntry | |||
| prtCfgParamCnfgIdx | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtCfgParamIdx | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.2 | ||
| A unique identifier of the port (within the card when applicable). - For KM-2100: Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. - For FCD-T1/E1: SUB=113, CH1=122, CH2=124. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtCfgParamSlt | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. notApplicable(255) - for products that do not have Slots. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255) | ||
| prtCfgParamOperatedMl | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.4 | ||
| The main link for this channel. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), kmxMlA(103), kmxMlB(104) | ||
| prtCfgParamMlAtoMlBPrio | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.5 | ||
| ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), low(2), high(3) | ||
| prtCfgParamMlBtoMlAPrio | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.6 | ||
| ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), low(2), high(3) | ||
| prtCfgParamInbandLoopDetection | 1.3.6.1.4.1.164.3.3.3.1.7.1.1.7 | ||
| Inband Loop Detection. The field is relevant for the following FCD-T1/E1 ports: SUB, CH1, CH2. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtT1E1 | 1.3.6.1.4.1.164.3.3.3.2 | ||
| OBJECT IDENTIFIER | |||
| prtT1E1StatTable | 1.3.6.1.4.1.164.3.3.3.2.1 | ||
| T1/E1 port statistics table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtT1E1StatEntry | |||
| prtT1E1StatEntry | 1.3.6.1.4.1.164.3.3.3.2.1.1 | ||
| An entry in the T1/E1 port statistics table. | |||
| OBJECT-TYPE | |||
| PrtT1E1StatEntry | |||
| prtT1E1SPrtIdx | 1.3.6.1.4.1.164.3.3.3.2.1.1.1 | ||
| This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT1E1SSlt | 1.3.6.1.4.1.164.3.3.3.2.1.1.2 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| prtT1E1OosCount | 1.3.6.1.4.1.164.3.3.3.2.1.1.3 | ||
| This object is applicable only for an E1 active port. It provides the number of red alarm events since the last count clearing. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtT1E1BpvLastMin | 1.3.6.1.4.1.164.3.3.3.2.1.1.4 | ||
| This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtT1E1BpvMax | 1.3.6.1.4.1.164.3.3.3.2.1.1.5 | ||
| This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtT1E1CnfgTable | 1.3.6.1.4.1.164.3.3.3.2.2 | ||
| T1/E1 port configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtT1E1CnfgEntry | |||
| prtT1E1CnfgEntry | 1.3.6.1.4.1.164.3.3.3.2.2.1 | ||
| An entry in the T1/E1 port configuration table. | |||
| OBJECT-TYPE | |||
| PrtT1E1CnfgEntry | |||
| prtT1E1CnfgIdx | 1.3.6.1.4.1.164.3.3.3.2.2.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtT1E1PrtIdx | 1.3.6.1.4.1.164.3.3.3.2.2.1.2 | ||
| This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . In the Kilomux, the port index is calculated as follows: 100*Slot+Ch. The external Ch numbers are 1..10, and the internal Ch numbers are 11..20. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT1E1Slt | 1.3.6.1.4.1.164.3.3.3.2.2.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), kmxMlA(103), kmxMlB(104), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), standAlone(255) | ||
| prtT1E1LineType | 1.3.6.1.4.1.164.3.3.3.2.2.1.4 | ||
| This variable indicates the variety of T1/E1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: esf Extended SuperFrame DS1 d4 AT&T D4 format DS1 - SF e1 CCITT Recommendation G.704 (Table 4a) - G732N e1Crc CCITT Recommendation G.704 (Table 4b) - G732N with CRC e1MF G.704 (Table 4a) with TS16 multiframing enabled - G732S e1CrcMF G.704 (Table 4b) with TS16 multiframing enabled - G732S with CRC unframed T1 - applicable values: (1),(2),(3),(8) E1 - applicable values: (1),(4),(5),(6),(7),(8) | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), esf(2), d4(3), e1(4), e1Crc(5), e1MF(6), e1CrcMF(7), unframed(8) | ||
| prtT1E1LineCode | 1.3.6.1.4.1.164.3.3.3.2.2.1.5 | ||
| This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. jbzs=b7zs refers the Jammed Bit Zero Suppres- sion, in which the AT&T specification of at least one pulse every 8 bit periods is literal- ly implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data (used for T1). b8zs refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits (used for T1). ANSI Clear Channels may use zbtsi, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use hdb3 or ami (= TRAN). amI (=TRAN) refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data. | |||
| OBJECT-TYPE | |||
| INTEGER | jbzs(1), b8zs(2), hdb3(3), zbtsi(4), ami(5), other(6) | ||
| prtT1E1SignalMode | 1.3.6.1.4.1.164.3.3.3.2.2.1.6 | ||
| 'none' indicates that no bits are reserved for signaling on this channel. 'robbedBit' indicates that T1 Robbed Bit Signaling is in use. 'bitOriented' indicates that E1 Channel Associated Signaling (CAS) is in use. 'messageOriented' indicates that Common Channel Signaling (CCS) is in use either on channel 16 of an E1 link or channel 24 of a T1. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), robbedBit(2), bitOriented(3), messageOriented(4) | ||
| prtT1E1Fdl | 1.3.6.1.4.1.164.3.3.3.2.2.1.7 | ||
| This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'ansi-T1-403' refers to the FDL exchange recommended by ANSI. 'att-54016' refers to ESF FDL exchanges. 'fdl-none' indicates that the device does not use the FDL. 'transFdl' indicates transition between two ports of the same card. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), ansi-T1-403(2), att-54016(4), fdl-none(8), transFdl(16) | ||
| prtT1E1FdlMode | 1.3.6.1.4.1.164.3.3.3.2.2.1.8 | ||
| Fdl Mode of the T1 selected port. notApplicable - will be used for an E1 port. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), user(2), carrier(3), notApplicable(255) | ||
| prtT1E1Sync | 1.3.6.1.4.1.164.3.3.3.2.2.1.9 | ||
| This object enables returning to normal operation, after the end of a main/sub link red alarm event, in reduced time. 'tr62411' - complies with AT&T TR-62411 (after 10 seconds). Applicable for both T1 and E1 interfaces. 'ccitt' - complies with CCITT standard. Applicable only for E1 interfaces. 'fast' - after 1 second. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), tr62411(2), ccitt(3), fast(4) | ||
| prtT1E1CGA | 1.3.6.1.4.1.164.3.3.3.2.2.1.10 | ||
| This object selects the method used to signal the CGA state to the other end, through the main/sub link. 'none' - non-transparent mode. When one of the links (main/sub) will be in Out Of Service state, both 'Data/Voice Oos' and 'Oos Signal' will be transmitted to the other end. 'trans' - when one of the links (main/sub) will be in Out Of Service state, 'Data/Voice Oos' will be transmitted to the other end. 'full' - fully-transparent mode. When one of the links (main/sub) will be in Out Of Service state, neither 'Data/Voice Oos' nor 'Oos Signal' will be transmitted to the other end. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), trans(2), full(3) | ||
| prtT1E1IdleCode | 1.3.6.1.4.1.164.3.3.3.2.2.1.11 | ||
| This object selects the code transmitted to fill idle (unused) time slots in the main link frame. Valid range: (0 - FF HEX) . | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtT1E1OosSignal | 1.3.6.1.4.1.164.3.3.3.2.2.1.12 | ||
| 'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. 'busyIdle' = MK_SP = A and B bits are forced to '1' for 2.5 seconds; then they are switched to '0' until out-of-service condition disappears. 'idleBusy' = SP_MK = A and B bits are forced to '0' for 2.5 seconds; then they are switched to '1' until out-of-service condition disappears. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0 | |||
| OBJECT-TYPE | |||
| INTEGER | notsupported(2), forcedIdle(3), forcedBusy(4), busyIdle(5), idleBusy(6) | ||
| prtT1E1VoiceOos | 1.3.6.1.4.1.164.3.3.3.2.2.1.13 | ||
| Voice Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtT1E1DataOos | 1.3.6.1.4.1.164.3.3.3.2.2.1.14 | ||
| Data Out-Of-Service code. Valid range: (0 - FF HEX). For agents that do not support this feature, the value will always be 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..4) | ||
| prtT1E1LineLengthMask | 1.3.6.1.4.1.164.3.3.3.2.2.1.15 | ||
| This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), fcc68(7) | ||
| prtT1E1TxGainMask | 1.3.6.1.4.1.164.3.3.3.2.2.1.16 | ||
| This attribute is the tx gain mask parameter (dB), used only for T1/CSU interfaces. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), txGain0db(2), txGain7dot5db(3), txGain15db(4), txGain22dot5db(5) | ||
| prtT1E1InbandMng | 1.3.6.1.4.1.164.3.3.3.2.2.1.17 | ||
| A unique number to identify an Inband management over the link. internal - supported by KM-2100 only. It means that the management is internal to the frame. It takes part of the ML Frame bits (instead of data). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), fdlOrTs0(3), dedicatedTs(4), dedicatedPpp(5), dedicatedFr(6), internal(7) | ||
| prtT1E1InbandMngRate | 1.3.6.1.4.1.164.3.3.3.2.2.1.18 | ||
| A unique number to identify the rate of the Inband management. It is required only for E1 links and is applicable only when prtExT1E1InbandMng selected is FdlOrTs0 or dedicatedTs. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r4k(2), r8k(3), r12k(4), r16k(5), r32k(6), r64k(7), r20k(8) | ||
| prtT1E1DedicatedTs | 1.3.6.1.4.1.164.3.3.3.2.2.1.19 | ||
| The value is differently determined for different products. There are two methods: 1) A unique number to identify Dedicated TS of the T1/E1 port. It is applicable only when prtExT1E1InbandMng selected is dedicatedTs. 1..24 - Dedicated TS of T1 1..31 - Dedicated TS of E1 255 - notApplicable (for agents that do not support this feature) Other values are invalid. 2) For FCD-STM, up to five TSs may be dedicated to management. This object value is the Sum (sigma) of 2**n, where n =TS-1 e.g. Time slots 3,5,7,9,11 are dedicated to management: 2** 2 +2** 4 +2** 6 +2** 8 +2**10 = 4+16+64+256+1024=1364 User should consult the product specification, to find out the method employed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT1E1InbandMngRoutProt | 1.3.6.1.4.1.164.3.3.3.2.2.1.20 | ||
| Inband Mng Routing Protocol of the port. When prtT1E1InbandMng is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. For FCD-M and FCD-A: When prtT1E1InbandMng is 'dedicatedPpp' or 'dedicatedFr': 'None', 'proprietary' and 'rip2' are applicable. When prtT1E1InbandMng is 'fdlOrTS0' or 'dedicatedTs': 'None' and 'proprietary' are applicable. When prtT1E1InbandMng is 'off': 'None' is applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| prtT1E1LinkMode | 1.3.6.1.4.1.164.3.3.3.2.2.1.21 | ||
| regular - TSs are connected by user via TS Assignment only transparent - when a port with this Link Mode is connected to an internal T1/E1 port of a T3/E3 card, TS0, TS16 and Fbit are transparently transferred to the E3/T3 stream. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), regular(2), transparent(3) | ||
| prtT1E1Multiplier | 1.3.6.1.4.1.164.3.3.3.2.2.1.22 | ||
| The data rate of each TS. The multiplier values can be 56 kbps or 64 kbps. For T1 only. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), br56(2), br64(3) | ||
| prtT1E1RxGain | 1.3.6.1.4.1.164.3.3.3.2.2.1.23 | ||
| This attribute is the rx volume (dB). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), rxGain12dB(2), rxGain30dB(3), rxGain36dB(4), shortHaul(5), longHaul(6) | ||
| prtT1E1RAI | 1.3.6.1.4.1.164.3.3.3.2.2.1.24 | ||
| Remote Alarm Signal | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtT1E1LineMode | 1.3.6.1.4.1.164.3.3.3.2.2.1.25 | ||
| Interface type of the port. For T1 - csu, dsu are the valid values For E1 - dsu, ltu are the valid values | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), csu(2), dsu(3), ltu(4) | ||
| prtT1E1TS0SaBits | 1.3.6.1.4.1.164.3.3.3.2.2.1.26 | ||
| This object is applicable only for E1 ports. For T1, string size will be 0. For E1, it enables user to select the use of TS0 Sa Bits 4..8, by 3 octets: The order (in hexa display): free Sa-Bit-4 Sa-Bit-5 Sa-Bit-6 Sa-Bit-7 Sa-Bit-8 |___________| |________________| |________________| MSByte LSByte Each Sa Bit will be represented by a nibble, having the following meaning: 0000 = zero 0001 = one 0010 = management 0011 = transparent the rest are reserved for future use. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtT1E1ConnectedTS | 1.3.6.1.4.1.164.3.3.3.2.2.1.27 | ||
| This parameter indicates if there is any connected TS for this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtT1E1Ts0SaBit | 1.3.6.1.4.1.164.3.3.3.2.2.1.28 | ||
| This parameter indicates whether to send TS 0, or not. noMng= TS 0 is looped, therefore not sent. mng= TS 0 isn't looped, therefore it is sent. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), noMng(2), mng(3) | ||
| prtT1E1SameFeCnfg | 1.3.6.1.4.1.164.3.3.3.2.2.1.29 | ||
| This parameter indicates whether the same E1 configuration parameters and TS assignment are set both to the local and remote device. Read-Write access is applicable only in G732N framed mode. For G732S and UNFRAMED this parameter is set by agent to YES and is Read Only. In Case of conflict during power-up between the central and remote, the value set by the central unit is the valid one. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtT1E1RemCrc4 | 1.3.6.1.4.1.164.3.3.3.2.2.1.30 | ||
| This object indicates whether the E1 of the Remote device connected to this E1 port, will have CRC-4 or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtT1E1MaxTSs | 1.3.6.1.4.1.164.3.3.3.2.2.1.31 | ||
| This object is applicable only for DXC D4T1, D4E1, D8T1, D8E1 external ports and D8GSL internal E1 ports. It is relevant only when sysCIntTsAllocMode=static(2). 255=not applicable If prtT1E1LineType=unframed(8), the value of this object must be 32. Else, the valid values are 0..31. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT1E1EocTsConfig | 1.3.6.1.4.1.164.3.3.3.2.2.1.32 | ||
| This object indicates whether the use of EOC for TS Configuration is enabled or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtT1E1FdlMsgTable | 1.3.6.1.4.1.164.3.3.3.2.3 | ||
| This table is applicable for a T1 interface with 'esf' LineType or E1 interface, when CRC is enabled (LineType). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtT1E1FdlMsgEntry | |||
| prtT1E1FdlMsgEntry | 1.3.6.1.4.1.164.3.3.3.2.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtT1E1FdlMsgEntry | |||
| prtT1E1FdlMsgPrtIdx | 1.3.6.1.4.1.164.3.3.3.2.3.1.1 | ||
| This attribute indicates a unique port number. The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The outside ports will be the T1/E1 cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT1E1FdlMsgFdlType | 1.3.6.1.4.1.164.3.3.3.2.3.1.2 | ||
| The Fdl type reference of the Fdl message. | |||
| OBJECT-TYPE | |||
| INTEGER | send(1), receive(2) | ||
| prtT1E1FdlMsgSlt | 1.3.6.1.4.1.164.3.3.3.2.3.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| prtT1E1FdlMsg | 1.3.6.1.4.1.164.3.3.3.2.3.1.4 | ||
| FDL message. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| prtHS | 1.3.6.1.4.1.164.3.3.3.3 | ||
| OBJECT IDENTIFIER | |||
| prtHSParamTable | 1.3.6.1.4.1.164.3.3.3.3.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtHSParamEntry | |||
| prtHSParamEntry | 1.3.6.1.4.1.164.3.3.3.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtHSParamEntry | |||
| prtHSCnfgIdx | 1.3.6.1.4.1.164.3.3.3.3.1.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtHSPrtIdx | 1.3.6.1.4.1.164.3.3.3.3.1.1.2 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtHSSlt | 1.3.6.1.4.1.164.3.3.3.3.1.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| prtHSRate | 1.3.6.1.4.1.164.3.3.3.3.1.1.4 | ||
| This object indicates the port rate (speed). auto - rate is selected automatically by system. | |||
| OBJECT-TYPE | |||
| INTEGER | r0x56eq0Kbps(1), r1x56eq56Kbps(2), r2x56eq112Kbps(3), r3x56eq168Kbps(4), r4x56eq224Kbps(5), r5x56eq280Kbps(6), r6x56eq336Kbps(7), r7x56eq392Kbps(8), r8x56eq448Kbps(9), r9x56eq504Kbps(10), r10x56eq560Kbps(11), r11x56eq616Kbps(12), r12x56eq672Kbps(13), r13x56eq728Kbps(14), r14x56eq784Kbps(15), r15x56eq840Kbps(16), r16x56eq896Kbps(17), r17x56eq952Kbps(18), r18x56eq1008Kbps(19), r19x56eq1064Kbps(20), r20x56eq1120Kbps(21), r21x56eq1176Kbps(22), r22x56eq1232Kbps(23), r23x56eq1288Kbps(24), r24x56eq1344Kbps(25), r25x56eq1400Kbps(26), r26x56eq1456Kbps(27), r27x56eq1512Kbps(28), r28x56eq1568Kbps(29), r29x56eq1624Kbps(30), r30x56eq1680Kbps(31), r31x56eq1736Kbps(32), r0x64eq0Kbps(33), r1x64eq64Kbps(34), r2x64eq128Kbps(35), r3x64eq192Kbps(36), r4x64eq256Kbps(37), r5x64eq320Kbps(38), r6x64eq384Kbps(39), r7x64eq448Kbps(40), r8x64eq512Kbps(41), r9x64eq576Kbps(42), r10x64eq640Kbps(43), r11x64eq704Kbps(44), r12x64eq768Kbps(45), r13x64eq832Kbps(46), r14x64eq896Kbps(47), r15x64eq960Kbps(48), r16x64eq1024Kbps(49), r17x64eq1088Kbps(50), r18x64eq1152Kbps(51), r19x64eq1216Kbps(52), r20x64eq1280Kbps(53), r21x64eq1344Kbps(54), r22x64eq1408Kbps(55), r23x64eq1472Kbps(56), r24x64eq1536Kbps(57), r25x64eq1600Kbps(58), r26x64eq1664Kbps(59), r27x64eq1728Kbps(60), r28x64eq1792Kbps(61), r29x64eq1856Kbps(62), r30x64eq1920Kbps(63), r31x64eq1984Kbps(64), r32x64eq2048Kbps(65), r32x56eq1792Kbps(66), r64x64eq4096Kbps(67), auto(200) | ||
| prtHSFifoSize | 1.3.6.1.4.1.164.3.3.3.3.1.1.5 | ||
| This object selects the size of the user data channel buffer FIFO used in the DTE2 mode. In the other modes, buffer size is automatically set by the DACS agent. Buffer FIFO size in bits, corresponds to FIFO lengths of +/-16, +/-30, +/-52, +/-72 bits. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), b32bit(2), b60bit(3), b104bit(4), b144bit(5), notApplicable(255) | ||
| prtHSClkMode | 1.3.6.1.4.1.164.3.3.3.3.1.1.6 | ||
| Clock Mode of the user data channel. dce - DACS operates as a DCE and provides transmit and receive clocks to the synchronous user DTE. dte1- DACS supplies the receive clock to the user equipment and accepts the user transmit clock. dte2- DACS requires transmit and receive clocks from the user equipment. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), dte1(2), dte2(3), notApplicable(255) | ||
| prtHSCTS | 1.3.6.1.4.1.164.3.3.3.3.1.1.7 | ||
| Selection of CTS line state in the user data channel. on - CTS continuously ON. rts - CTS line follows the RTS line. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), rts(2), notApplicable(255) | ||
| prtHSRtsState | 1.3.6.1.4.1.164.3.3.3.3.1.1.8 | ||
| RTS state of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), notApplicable(255) | ||
| prtHSInbandLoopback | 1.3.6.1.4.1.164.3.3.3.3.1.1.9 | ||
| This object indicates if Inband Loopback from the Network should be enabled or disabled. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtHSInbandLoopPatternCfg | 1.3.6.1.4.1.164.3.3.3.3.1.1.10 | ||
| This object indicates if Inband Loop polynomial pattern will be according to RDL Loop (the standard) or User Configurated according to prtHSActivatePolyPattern and prtHSDeactivatePolyPattern. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), rdlLoop(2), userConfig(3) | ||
| prtHSInbandLoopActPattern | 1.3.6.1.4.1.164.3.3.3.3.1.1.11 | ||
| This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Activate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| prtHSInbandLoopDeactPattern | 1.3.6.1.4.1.164.3.3.3.3.1.1.12 | ||
| This object is a binary string of up to 8 bits. Though the syntax allows for any ASCII characters, for this object only '0' or '1' characters are valid. The string determines coefficients of the polynomial pattern sent to the port in order to Deactivate the Inband Loop. This object is relevant only when prtHSInbandLoopPatternCfg=userConfig. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| prtHSDCD | 1.3.6.1.4.1.164.3.3.3.3.1.1.13 | ||
| Selection of DCD line state in the user data channel. linkOK - DCD line is ON only when active link is OK. on - DCD continuously ON. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), linkOK(2), on(3) | ||
| prtHSBertTable | 1.3.6.1.4.1.164.3.3.3.3.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtHSBertEntry | |||
| prtHSBertEntry | 1.3.6.1.4.1.164.3.3.3.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtHSBertEntry | |||
| prtHSBertPrtIdx | 1.3.6.1.4.1.164.3.3.3.3.2.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The inside ports will be the HS cards ports. The convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtHSBertSlt | 1.3.6.1.4.1.164.3.3.3.3.2.1.2 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| prtHSBertCountClr | 1.3.6.1.4.1.164.3.3.3.3.2.1.3 | ||
| Setting this object (to on) initiate bert counter clear operation. Valid only when bert test is active on the specific port. (Every time a new bert test starts, the counter is automatically cleared; this command enables clearing the counter while the test is running). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtHSBertTestResult | 1.3.6.1.4.1.164.3.3.3.3.2.1.4 | ||
| This object indicates the number of Bit Error Rate indicated during the BERT test. Active only when bert test is running on the selected port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSP | 1.3.6.1.4.1.164.3.3.3.4 | ||
| OBJECT IDENTIFIER | |||
| prtSpCnfgTable | 1.3.6.1.4.1.164.3.3.3.4.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSpCnfgEntry | |||
| prtSpCnfgEntry | 1.3.6.1.4.1.164.3.3.3.4.1.1 | ||
| All the entries at this table are identical(have the same value) at all the configurations(1..255) except at the TmpCnfg. - For products supporting more than one configuration, the write operation into the Table Objects is valid only at the TmpCnfg entry. - For products that do not support configurations, the write operation into the Table Objects will be to prtSpCnfgIdx=1. | |||
| OBJECT-TYPE | |||
| PrtSpCnfgEntry | |||
| prtSpCnfgIdx | 1.3.6.1.4.1.164.3.3.3.4.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtSpPrtIdx | 1.3.6.1.4.1.164.3.3.3.4.1.1.2 | ||
| This attribute indicates a unique port number of the SPor DP port. For DXC, it is the port in the active DCL card: - SP = 1 - NP ; DP = 2 For Kilomux, the port index is calculated as follows: 100*Slot+Ch. For FCD, PRBi, the SP port index=1. For Optimux-T3, the SP port index=71. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSpUsage | 1.3.6.1.4.1.164.3.3.3.4.1.1.3 | ||
| This attribute indicates what is the usage of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), noUse(2), nmsSlip(3), nmsPpp(4), muxSlip(5), muxPpp(6), terminal(7), dialOut(8) | ||
| prtSpRate | 1.3.6.1.4.1.164.3.3.3.4.1.1.4 | ||
| This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), s300bps(2), s1200bps(3), s2400bps(4), s4800bps(5), s9600bps(6), s19200bps(7), s38400bps(8), s57600bps(9), s115200bps(10) | ||
| prtSpDataBits | 1.3.6.1.4.1.164.3.3.3.4.1.1.5 | ||
| This attribute indicates the number of data bits in async frame | |||
| OBJECT-TYPE | |||
| INTEGER | dataBits7(1), dataBits8(2) | ||
| prtSpParity | 1.3.6.1.4.1.164.3.3.3.4.1.1.6 | ||
| This attribute indicates the parity mode in async frame | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), odd(2), even(3) | ||
| prtSpCallOutMode | 1.3.6.1.4.1.164.3.3.3.4.1.1.7 | ||
| This attribute indicates the call-out mode. For DXC - this object is applicable only for the DP port (2). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), all(3), major(4) | ||
| prtSpInterface | 1.3.6.1.4.1.164.3.3.3.4.1.1.8 | ||
| This attribute indicates the supervisory port interface. dce - the DACS appears as a DCE for the port. dte - the DACS operates as a DTE, for connection via modem, for the port. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), dte(2) | ||
| prtSpCTS | 1.3.6.1.4.1.164.3.3.3.4.1.1.9 | ||
| CTS line state. This object is applicable only for port (1) = SP | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), rts(3) | ||
| prtSpDcdDelay | 1.3.6.1.4.1.164.3.3.3.4.1.1.10 | ||
| DCD delay in msec. d10 = delay of 10msec. This object is applicable only for port (1) = SP | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), d0(2), d10(3), d50(4), d100(5), d200(6), d300(7) | ||
| prtSpDsr | 1.3.6.1.4.1.164.3.3.3.4.1.1.11 | ||
| DSR line state. This object is applicable only for port (1) = SP | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), dtr(3) | ||
| prtSpNoOfRetries | 1.3.6.1.4.1.164.3.3.3.4.1.1.12 | ||
| For DXC - this object is applicable only for port (2) = DP. The number of dialing retries requested. Default = 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8 | ||
| prtSpWaitForConnect | 1.3.6.1.4.1.164.3.3.3.4.1.1.13 | ||
| For DXC - this object is applicable only for port (2) = DP. Waiting time for connect, in seconds. Default = 30 sec. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), t30sec(2), t45sec(3), t60sec(4) | ||
| prtSpDialMode | 1.3.6.1.4.1.164.3.3.3.4.1.1.14 | ||
| For DXC - this object is applicable only for port (2) = DP. Dialing mode. Default=tone | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), tone(2), pulse(3) | ||
| prtSpAltNumMode | 1.3.6.1.4.1.164.3.3.3.4.1.1.15 | ||
| For DXC - this object is applicable only for port (2) = DP. It determines wether to use the alternate number or not. Default = no. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtSpPrimaryNum | 1.3.6.1.4.1.164.3.3.3.4.1.1.16 | ||
| For DXC - this object is applicable only for port (2) = DP. It is the Primary dialing number. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..20) | ||
| prtSpAltNum | 1.3.6.1.4.1.164.3.3.3.4.1.1.17 | ||
| For DXC - this object is applicable only for port (2) = DP. It is the Alternate dialing number. This number is applicable only if prtSpAltNumMode is 'yes'. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..20) | ||
| prtSpRoutProtocol | 1.3.6.1.4.1.164.3.3.3.4.1.1.18 | ||
| This attribute indicates the routing protocol of the port. notApplicable - for DP. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| prtSpCmd | 1.3.6.1.4.1.164.3.3.3.4.1.1.19 | ||
| SP Command. For LRS this parameter will be used for a Modem Command. Upon NMS's Get operation for devices that this parameter is notApplicable, agent will send NULL string. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(20) | ||
| prtSpActCallOut | 1.3.6.1.4.1.164.3.3.3.4.1.1.20 | ||
| This object indicates when to Activate Call-Out. It is used by FCD-T1/E1. always - to activate call-out always. linkFail - to activate call-out only when Link of Inband Management fails. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), always(2), linkFail(3) | ||
| prtSpAlrRelayMode | 1.3.6.1.4.1.164.3.3.3.4.1.1.21 | ||
| This attribute indicates the Alarm Relay Mode. notApplicable - for DP. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), normal(2), invert(3) | ||
| prtSpStopBits | 1.3.6.1.4.1.164.3.3.3.4.1.1.22 | ||
| This attribute indicates number of stop bits in an async frame. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), stopBits1(2), stopBits1dot5(3), stopBits2(4) | ||
| prtDim | 1.3.6.1.4.1.164.3.3.3.5 | ||
| OBJECT IDENTIFIER | |||
| prtDimCnfgTable | 1.3.6.1.4.1.164.3.3.3.5.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtDimCnfgEntry | |||
| prtDimCnfgEntry | 1.3.6.1.4.1.164.3.3.3.5.1.1 | ||
| The write operation into the Table Objects is valid only for the TmpCnfg entry (prtDimCnfgIdx=255). | |||
| OBJECT-TYPE | |||
| PrtDimCnfgEntry | |||
| prtDimCnfgIdx | 1.3.6.1.4.1.164.3.3.3.5.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtDimIdx | 1.3.6.1.4.1.164.3.3.3.5.1.1.2 | ||
| This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10)*10 + 1 Example: port1 of IO slot 11 will be: 211 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDimTxMode | 1.3.6.1.4.1.164.3.3.3.5.1.1.3 | ||
| Tx mode. regularTx - the links are connected to a similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is decreased accordingly. broadcast - the links are connected to MORE than one similar outfit on the other side. In this mode, if a link fails, the transmitted bandwidth is not affected | |||
| OBJECT-TYPE | |||
| INTEGER | regularTx(2), broadcast(3) | ||
| prtDimPolarity | 1.3.6.1.4.1.164.3.3.3.5.1.1.4 | ||
| Polarity. | |||
| OBJECT-TYPE | |||
| INTEGER | normalClk(2), inverted(3) | ||
| prtDimClkMode | 1.3.6.1.4.1.164.3.3.3.5.1.1.5 | ||
| Clock Mode. smooth - a clock that is not 'pulsed'(has no 'gaps'). In this mode the DXC does NOT receive back the clock signal. extSmooth - same as 'smooth' but in this mode, the DXC receives back the clock signal. | |||
| OBJECT-TYPE | |||
| INTEGER | extDce(2), dce(3), smooth(4), extSmooth(5) | ||
| prtDimMaxDelay | 1.3.6.1.4.1.164.3.3.3.5.1.1.6 | ||
| Max Delay permitted between the links, in msec. | |||
| OBJECT-TYPE | |||
| INTEGER | t16msec(2), t64msec(3) | ||
| prtDimMng | 1.3.6.1.4.1.164.3.3.3.5.1.1.7 | ||
| Use of DIM port for management. disabled - no management on DIM ts1 - 1 bit of TS1 is used for management. | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(2), ts1(3) | ||
| prtDimDestTable | 1.3.6.1.4.1.164.3.3.3.5.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtDimDestEntry | |||
| prtDimDestEntry | 1.3.6.1.4.1.164.3.3.3.5.2.1 | ||
| The write operation is valid only for the TmpCnfg entry (prtDimDestCnfgIdx=255). | |||
| OBJECT-TYPE | |||
| PrtDimDestEntry | |||
| prtDestCnfgIdx | 1.3.6.1.4.1.164.3.3.3.5.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg(1..255) being accessed. Idx of 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtDestDimIdx | 1.3.6.1.4.1.164.3.3.3.5.2.1.2 | ||
| This attribute indicates a unique port number of the DIM card. The convention used for DXC: (IO slot number+10) & 1 Example: port1 of IO slot 11 will be: 211 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDestIdx | 1.3.6.1.4.1.164.3.3.3.5.2.1.3 | ||
| This attribute indicates a destination number of the DIM card. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| prtDest | 1.3.6.1.4.1.164.3.3.3.5.2.1.4 | ||
| Destination port,(of a T1/E1 port), that is connected to the DIM card, for the specified Destination number. 0 = No destination port. Else: For external ports: (IO Slot+10) & 1 for port 1 (IO Slot+10) & 3 for port 2 Example: port2 of IO slot 12 will be: 223 . For internal ports : (IO Slot+10) & 2 for port 1 (IO Slot+10) & 4 for port 2 (IO Slot+10) & 6 for port 3 (IO Slot+10) & 8 for port 4, etc... | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtDestConnect | 1.3.6.1.4.1.164.3.3.3.5.2.1.5 | ||
| Connection Status of the specified destination number. For a specified destination port, it depends both on the status of the port and on the status of the far-end port. Since this is a RO object, same value will be received for all configurations. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| prtI | 1.3.6.1.4.1.164.3.3.3.6 | ||
| OBJECT IDENTIFIER | |||
| prtICnfgTable | 1.3.6.1.4.1.164.3.3.3.6.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtICnfgEntry | |||
| prtICnfgEntry | 1.3.6.1.4.1.164.3.3.3.6.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtICnfgEntry | |||
| prtICnfgIdx | 1.3.6.1.4.1.164.3.3.3.6.1.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtIIdx | 1.3.6.1.4.1.164.3.3.3.6.1.1.2 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. * The ISDN B1, B2, D channels will be inside ports. For port index, see product specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIRate | 1.3.6.1.4.1.164.3.3.3.6.1.1.3 | ||
| This object indicates the port rate in bits. Each TS contains 8 bits. Thus, 1 bit is equivalent to 8Kbps rate. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), nc(2), r2bit(3), r4bit(4), r8bit(5) | ||
| prtIConnect | 1.3.6.1.4.1.164.3.3.3.6.1.1.4 | ||
| D channel connection. no - disconnected yes - connected. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtHdsl | 1.3.6.1.4.1.164.3.3.3.7 | ||
| OBJECT IDENTIFIER | |||
| prtHdslTable | 1.3.6.1.4.1.164.3.3.3.7.1 | ||
| HDSL port table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtHdslEntry | |||
| prtHdslEntry | 1.3.6.1.4.1.164.3.3.3.7.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtHdslEntry | |||
| prtHdslIdx | 1.3.6.1.4.1.164.3.3.3.7.1.1.1 | ||
| This attribute indicates a unique number to identify a port. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The HDSL ports will be external. For port index, see product specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtHdslMode | 1.3.6.1.4.1.164.3.3.3.7.1.1.2 | ||
| This object indicates the HDSL mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), central(2), remote(3) | ||
| prtHdslRptrType | 1.3.6.1.4.1.164.3.3.3.7.1.1.3 | ||
| The Repeater between Near and Far modem. none - no repeater exists between the modems hrpt - HRPT repeater exists between the modems. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), hrpt(3) | ||
| prtHdslMaxRate | 1.3.6.1.4.1.164.3.3.3.7.1.1.4 | ||
| Maximum Rate of the xDSL Line, in Kbps units. This object can be Set only for a Central unit. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r192(2), r256(3), r320(4), r384(5), r448(6), r512(7), r576(8), r640(9), r768(10), r896(11), r1024(12), r1152(13), r1280(14), r1536(15), r1920(16), r2048(17) | ||
| prtHdslLinkType | 1.3.6.1.4.1.164.3.3.3.7.1.1.5 | ||
| The Link Type. msdsl2w - MSDSL 2 Wire hdsl2w - HDSL 2 Wire hdsl4w - HDSL 4 Wire gDsl - G.DSL | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), msdsl2w(2), hdsl2w(3), hdsl4w(4), gDsl(5) | ||
| prtHdslCompSwVer | 1.3.6.1.4.1.164.3.3.3.7.1.1.6 | ||
| This object indicates the Software Version of the component (Piggyback card) supporting this interface. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtHdslCompHwVer | 1.3.6.1.4.1.164.3.3.3.7.1.1.7 | ||
| This object indicates the Hardware Version of the component (Piggyback card) supporting this interface. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| prtT3E3 | 1.3.6.1.4.1.164.3.3.3.8 | ||
| OBJECT IDENTIFIER | |||
| prtT3E3CnfgTable | 1.3.6.1.4.1.164.3.3.3.8.1 | ||
| T3/E3 port configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtT3E3CnfgEntry | |||
| prtT3E3CnfgEntry | 1.3.6.1.4.1.164.3.3.3.8.1.1 | ||
| An entry in the T3/E3 port configuration table. | |||
| OBJECT-TYPE | |||
| PrtT3E3CnfgEntry | |||
| prtT3E3CnfgIdx | 1.3.6.1.4.1.164.3.3.3.8.1.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. For DXC, write operations can be performed only on the Temp Config. For products that do not support configurations, always 1 will be used. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtT3E3PrtIdx | 1.3.6.1.4.1.164.3.3.3.8.1.1.2 | ||
| This attribute indicates a unique port number. For DXC: The same numbering as for prtGenPrtIdx. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside. * The external ports convention used will be (for DXC): - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . For Optimux-T3: Link-A: 51 Link-B: 61 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtT3E3Slt | 1.3.6.1.4.1.164.3.3.3.8.1.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. When the unit is stand-alone, this object is not applicable and 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| prtT3E3LineLength | 1.3.6.1.4.1.164.3.3.3.8.1.1.4 | ||
| This object is the length of the ds3 line in feet. It provides information for line build out circuitry if it exists and can use this object to adjust the line build out. len0p450ft = 0 - 450 feet len451p900ft = 451 - 900 feet. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), len0p450ft(2), len451p900ft(3) | ||
| prtT3E3InbandMng | 1.3.6.1.4.1.164.3.3.3.8.1.1.5 | ||
| A unique number to identify the Frame Type over the link. For Optimux-T3: only values (4), (7) are supported. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), cBit(3), cBitTxRxMng(4), cBitTx(5), cBitTxMng(6), m13(7) | ||
| prtT3E3AisFrame | 1.3.6.1.4.1.164.3.3.3.8.1.1.6 | ||
| This object is applicable only for Optimux-T3. It allows user to select whether the AIS sent will be framed or unframed. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unframed(2), framed(3) | ||
| prtT3E3TxClockSource | 1.3.6.1.4.1.164.3.3.3.8.1.1.7 | ||
| Tx Clock Source. | |||
| OBJECT-TYPE | |||
| INTEGER | external(1), internal(2), notApplicable(255) | ||
| prtT3E3RoutProt | 1.3.6.1.4.1.164.3.3.3.8.1.1.8 | ||
| Routing Protocol of the port. This object is applicable only for T3 ports. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| genDacsMux | 1.3.6.1.4.1.164.3.3.4 | ||
| OBJECT IDENTIFIER | |||
| cmprTable | 1.3.6.1.4.1.164.3.3.4.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CmprEntry | |||
| cmprEntry | 1.3.6.1.4.1.164.3.3.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| CmprEntry | |||
| cmprTypeIdx | 1.3.6.1.4.1.164.3.3.4.1.1.1 | ||
| This object indicates the Type of the Compressed data referred (which table, which level, etc). The type is a code according to a convention between agent and NMS. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cmprCnfgIdx | 1.3.6.1.4.1.164.3.3.4.1.1.2 | ||
| This object indicates the configuration number the Compressed information relates to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cmprVersion | 1.3.6.1.4.1.164.3.3.4.1.1.3 | ||
| This object indicates the version of the internal format of the Compressed data (the version of the convention used). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cmprSltIdx | 1.3.6.1.4.1.164.3.3.4.1.1.4 | ||
| This attribute indicates a unique number of the slot position where the card is inserted. When the unit is stand-alone or this object is not applicable, 255 will be used. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), clA(3), clB(4), io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), notApplicable(255) | ||
| cmprPrtIdx | 1.3.6.1.4.1.164.3.3.4.1.1.5 | ||
| This object indicates a unique identifier of the port, the compressed information relates to. For DXC - according to the order in the card of cmprSltIdx: - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . For FCD: see product's specification. If the port number is irrelevant to this parameter (if it is a system/card level alarm) the value will be 9999. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cmprObj | 1.3.6.1.4.1.164.3.3.4.1.1.6 | ||
| This object is the compressed information itself, according to a predefined format, both agent and NMS agreed about. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mapLinkTable | 1.3.6.1.4.1.164.3.3.4.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MapLinkEntry | |||
| mapLinkEntry | 1.3.6.1.4.1.164.3.3.4.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MapLinkEntry | |||
| mapLinkIdx | 1.3.6.1.4.1.164.3.3.4.2.1.1 | ||
| A unique identifier of the link | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mapLinkSlotIdx | 1.3.6.1.4.1.164.3.3.4.2.1.2 | ||
| This attribute indicates a unique slot position where the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), io13(17), io14(18), io15(19), standAlone(255) | ||
| mapLinkPortIdx | 1.3.6.1.4.1.164.3.3.4.2.1.3 | ||
| This attribute indicates a unique port number. The valid port number depends on the IO slot no., the installed card type and the port type: outside, inside, SP. In the DXC : - first two digits will be: (IO slot number+10) - last one/two digits will be the port number within the card in odd or even numbers, as follows: * For the outside/external ports, in odd numbers: port1 = 1 port2 = 3 port3 = 5 etc... Example: port2 of IO slot 11 will be: 213 . * The inside/internal ports, in even numbers: port1 = 2 port2 = 4 port3 = 6 etc... Example: port2 of IO slot 11 will be: 214 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mapLinkState | 1.3.6.1.4.1.164.3.3.4.2.1.4 | ||
| This attribute indicates the status of the link between the two muxes | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), down(2), up(3) | ||
| alrGenTable | 1.3.6.1.4.1.164.3.3.4.3 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AlrGenEntry | |||
| alrGenEntry | 1.3.6.1.4.1.164.3.3.4.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| AlrGenEntry | |||
| alrGenCode | 1.3.6.1.4.1.164.3.3.4.3.1.1 | ||
| This object is a unique code number, identifying a certain alarm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| alrGenDescription | 1.3.6.1.4.1.164.3.3.4.3.1.2 | ||
| This entry is a unique text description, of the alarm corresponding to the specified code. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| alrGenLevel | 1.3.6.1.4.1.164.3.3.4.3.1.3 | ||
| Alarm level. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), system(2), card(3), port(4) | ||
| alrGenSlotType | 1.3.6.1.4.1.164.3.3.4.3.1.4 | ||
| Slot type that the alarm is relevant to. clAndIo - an alarm that is relevant for both CL and IO slots. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), ps(2), cl(3), io(4), clAndIo(5) | ||
| alrGenSeverity | 1.3.6.1.4.1.164.3.3.4.3.1.5 | ||
| This object enables the user to select a severity for each alarm. The severity is set per alarm code (same for all slots/ports using this code). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), event(3), minor(4), major(5), warning(6), critical(7) | ||
| alrGenDebounce | 1.3.6.1.4.1.164.3.3.4.3.1.6 | ||
| Debounce time for each alarm code, in seconds. The meaning is, that an alarm will be 'declared' as ON (or OFF), only after it was actually ON/OFF the Debouncing time selected by user. 0 = default debounce selection (each alarm has a default value). 250 = maximum value of seconds for debounce. 253 = mask = the alarm will Never be reported. 254 = default debounce selection (each alarm has a default value). 255 = not applicable | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| alrGenDefSeverity | 1.3.6.1.4.1.164.3.3.4.3.1.7 | ||
| This object reports the default severity of each alarm. User can change the severity of the alarms defined by this default via the alrGenSeverity object. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), event(3), minor(4), major(5) | ||
| modmSys | 1.3.6.1.4.1.164.3.4 | ||
| OBJECT IDENTIFIER | |||
| modmSysEvents | 1.3.6.1.4.1.164.3.4.0 | ||
| The events for General Modems. | |||
| OBJECT-IDENTITY | |||
| modmHubConfigChange | 1.3.6.1.4.1.164.3.4.0.3 | ||
| The trap is sent when any card of the modems Hub is inserted or removed. | |||
| NOTIFICATION-TYPE | |||
| mdlCardType | |||
| mdlSPanelType | |||
| modemMasterSlaveComm | 1.3.6.1.4.1.164.3.4.0.4 | ||
| This trap is applicable only for IMOD modems . The trap is sent when communication between a Master modem and its Slave is stopped or resumed. 'modemMngLink' includes the modemIdx. | |||
| NOTIFICATION-TYPE | |||
| modemMngLink | |||
| modemMasterChange | 1.3.6.1.4.1.164.3.4.0.5 | ||
| This trap is applicable only for IMOD modems . The trap is sent when a modem's permanent or temporary mode is changed. 'modemConfigMode' and 'modemModeTemporary' include the modemIdx. | |||
| NOTIFICATION-TYPE | |||
| modemConfigMode | |||
| modemModeTemporary | |||
| mngmntControlChange | 1.3.6.1.4.1.164.3.4.0.6 | ||
| This trap is applicable only for LRS-12. The trap is sent when the Hub management controller is changed (NMS<->Terminal). | |||
| NOTIFICATION-TYPE | |||
| modmHubController | |||
| modemInvalidParameter | 1.3.6.1.4.1.164.3.4.0.7 | ||
| This trap is applicable only for IMOD cards of a Hub. The trap is sent when an invalid parameter was Set to the modem. | |||
| NOTIFICATION-TYPE | |||
| modemIdx | |||
| modemAlarm | 1.3.6.1.4.1.164.3.4.0.8 | ||
| This trap is applicable only for IMOD modems . The trap is sent when the active alarms of an IMOD modem, change. | |||
| NOTIFICATION-TYPE | |||
| modemActiveAlarms | |||
| cardStatusChange | 1.3.6.1.4.1.164.3.4.0.9 | ||
| The trap is sent upon any change of the Leds status in the PS, CL or IMOD cards. | |||
| NOTIFICATION-TYPE | |||
| mdlSLed | |||
| modemSignalingChange | 1.3.6.1.4.1.164.3.4.0.10 | ||
| The trap is sent for any IMOD modem, when an unmasked signal change occured in the attached variable (see modemMaskSignaling object). | |||
| NOTIFICATION-TYPE | |||
| modmPrtDteSignaling | |||
| modmHubPsFail | 1.3.6.1.4.1.164.3.4.0.11 | ||
| The trap is sent when a PS card of the modems-Hub failed. 'mdlSLed' includes the mdlSIdx. | |||
| NOTIFICATION-TYPE | |||
| mdlSLed | |||
| modmHubIPModeChange | 1.3.6.1.4.1.164.3.4.0.12 | ||
| The trap is sent upon any change of modmHubIpMode parameter. | |||
| NOTIFICATION-TYPE | |||
| modmHubIpMode | |||
| modmInterfaceChange | 1.3.6.1.4.1.164.3.4.0.13 | ||
| The trap is sent upon any change of interfaces for a modem that is a card of a Hub or part of it. In order to know what changed, for each product, specific variables will be attached. These variables will be specified in the product's spec. For FOMi-E3/T3 and Optimux-4E1/T1-C : the trap will be sent when the connectors card in LRS is removed/inserted. | |||
| NOTIFICATION-TYPE | |||
| modmRackAlarms | 1.3.6.1.4.1.164.3.4.0.14 | ||
| The trap is applicable for LRS-52. The trap is sent when an alarm occurs. Attached variables are detailed in product specification. | |||
| NOTIFICATION-TYPE | |||
| modmSystem | 1.3.6.1.4.1.164.3.4.1 | ||
| OBJECT IDENTIFIER | |||
| modmSa | 1.3.6.1.4.1.164.3.4.1.1 | ||
| OBJECT IDENTIFIER | |||
| modmSaEvents | 1.3.6.1.4.1.164.3.4.1.1.0 | ||
| The events for Stand Alone Modems. | |||
| OBJECT-IDENTITY | |||
| modmSAlarmTrap | 1.3.6.1.4.1.164.3.4.1.1.0.1 | ||
| The trap is sent every 5 seconds in which a change has occurred in the status of the variables sent. For modems containing a T1/E1 interface, dsx1LineStatus will be sent as well in the variables, after modmSaStatAlarms. This trap is applicable for Stand-alone modems or Agents that are cards of a Hub. | |||
| NOTIFICATION-TYPE | |||
| modmSaStatAlarms | |||
| modmSLedTrap | 1.3.6.1.4.1.164.3.4.1.1.0.2 | ||
| The trap is sent every 5 seconds in which a change has occurred in the state of one of the LEDs. This trap is applicable for Stand-Alone modems or Agents that are cards of a Hub. 'agnLed' - will include both central and remote modems: first central, last remote. | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| modmSaConfigTable | 1.3.6.1.4.1.164.3.4.1.1.1 | ||
| Configuration parameters of the Central and Remote Modems. The table will be RW for a Central agent and RO for a Remote agent. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmSaConfigEntry | |||
| modmSaConfigEntry | 1.3.6.1.4.1.164.3.4.1.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmSaConfigEntry | |||
| modmSaConfigMode | 1.3.6.1.4.1.164.3.4.1.1.1.1.1 | ||
| The mode indicates if the configuration parameters refer the Central or the Remote Modem. For AMC 102 the remote means regenerator. There can be some regenerators connecting one by the other. | |||
| OBJECT-TYPE | |||
| INTEGER | central(1), remote(2), remote2(3), remote3(4), remote4(5), remote5(6), remote6(7), remote7(8), remote8(9), remote9(10), remote10(11) | ||
| modmSaConfigLoopback | 1.3.6.1.4.1.164.3.4.1.1.1.1.2 | ||
| The possible loopbacks. It is not possible to have a remPortLoop(4) in both, Central and Remote units simultaneously. | |||
| OBJECT-TYPE | |||
| INTEGER | noLoopback(1), localPortLoop(2), localLineLoop(3), remPortLoop(4) | ||
| modmSaConfigAlrClearOnCmd | 1.3.6.1.4.1.164.3.4.1.1.1.1.3 | ||
| Setting this attribute to on, clears all the events, both from the active alarms list and from the alarms buffer. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmSaConfigAlrClearAllCmd | 1.3.6.1.4.1.164.3.4.1.1.1.1.4 | ||
| Setting this attribute to on, clears all the alarms of the alarm buffer and active alarms list. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmSaConfigTestClearCmd | 1.3.6.1.4.1.164.3.4.1.1.1.1.5 | ||
| Setting this attribute to on, clears all the user-initiated tests and loopbacks. The variable modmSaConfigLoopback should automatically change to noLoopback. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmSaConfigClkMaster | 1.3.6.1.4.1.164.3.4.1.1.1.1.6 | ||
| Modem configured as Central: External - Locked to the clock signal provided by the user's equipment by user's port. Internal - Internal oscillator. Station - Station clock (is relevant only for cards). Modem configured as Remote: External - Always locked to the recovered receive clock of the HDSL line. | |||
| OBJECT-TYPE | |||
| INTEGER | external(2), internal(3), station(4) | ||
| modmSaConfigResetStatistics | 1.3.6.1.4.1.164.3.4.1.1.1.1.7 | ||
| In the on state all statistics counters (including E1 counters) are zeroed. Upon completion, the value will automatically change to off(2). Modems that do not support statistics - the value will always be off (this object is not applicable for them). notApplicable - for modems with no statistics support. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), notApplicable(255) | ||
| modmSaConfigActiveTs | 1.3.6.1.4.1.164.3.4.1.1.1.1.8 | ||
| This object will be RO for the Remote modem. This is the number of active HDSL Time Slots, that determines user's data rate. Valid values: 1..maximum supported by the specific modem. 255 = notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| modmSaConfigReset | 1.3.6.1.4.1.164.3.4.1.1.1.1.9 | ||
| Reset of modem. hw - HW Reset. The configured values will not change. hwAndConfig - HW Reset and initializing the default values. notApplicable - for modems with no Reset support. After 'hw' or 'hwAndConfig' is Set, agent will turn the value to 'off'. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), hw(3), hwAndConfig(4), notApplicable(255) | ||
| modmSaConfigRemote | 1.3.6.1.4.1.164.3.4.1.1.1.1.10 | ||
| This parameter enables or disables automatic configuration of the remote moden in Proxy mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| modmSaConfigPsType | 1.3.6.1.4.1.164.3.4.1.1.1.1.11 | ||
| The type of PS. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), ac(2), dc(3), ac-dc(4) | ||
| modmSaConfigWorkMode | 1.3.6.1.4.1.164.3.4.1.1.1.1.12 | ||
| The work mode indicates if devices work in transparent mode or termination mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), transparent(2), termination(3) | ||
| modmSaStatTable | 1.3.6.1.4.1.164.3.4.1.1.2 | ||
| Status of the Central and Remote Modems. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmSaStatEntry | |||
| modmSaStatEntry | 1.3.6.1.4.1.164.3.4.1.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmSaStatEntry | |||
| modmSaStatHwTest | 1.3.6.1.4.1.164.3.4.1.1.2.1.1 | ||
| The variable contains the results of the last hardware test. It is a sum of 2**n where n is as follows: 0 - EPROM Failure (or Database chksum error) 1 - I/O Expander Error 2 - Counter Error 3 - HDSL Framer Failure 4 - Transceiver Failure 5 - NVRAM Failure (applicable only for HCD-E1>=r3) 6 - NSFIFO Failure (applicable for HCD-E1>=r3 and HCD-4) 7 - BERT Failure (applicable only for HCD-E1>=r3) 8 - E1 Framer Failure (applicable only for HCD-E1>=r3) 9 - XRT Failure (applicable only for HCD-E1>=r3) 10- HDSL Framer 1 Failure (applicable only for HCD-4) 11- HDSL Framer 2 Failure (applicable only for HCD-4) 12- DSP 1 Failure (applicable only for HCD-4) 13- DSP 2 Failure (applicable only for HCD-4) 14- XRT 1 Failure (applicable only for HCD-4) 15- XRT 2 Failure (applicable only for HCD-4) if the variable is 0 then there are No Errors | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaStatAlarms | 1.3.6.1.4.1.164.3.4.1.1.2.1.2 | ||
| The variable contains the status of the Alarms in the alarm buffer. For bit location of each Alarm in the OctetString see Modem's specification. If the value is 0 then there are No 'On' Alarms in the alarm buffer. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(10) | ||
| modmSaStatClkSrc | 1.3.6.1.4.1.164.3.4.1.1.2.1.3 | ||
| This entry indicates the source of the modem clock. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), fallback(2) | ||
| modmSaStatAlarmsMask | 1.3.6.1.4.1.164.3.4.1.1.2.1.4 | ||
| This variable uses to mask alarms. Location of each Alarm Mask in the OctetString, is identical to the Alarm OctetString. If the value is 0 then none of the alarms is masked. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(10) | ||
| modmSaStatDeviceType | 1.3.6.1.4.1.164.3.4.1.1.2.1.5 | ||
| This entry indicates the device type (or utility). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), amc102SA(2), amc102Card(3) | ||
| modmSaStatSwVersion | 1.3.6.1.4.1.164.3.4.1.1.2.1.6 | ||
| Display String of the modem SW version. Format: W. X Y Z 0..9 0..99 A,B,E 0..99 (Z+P are optional.) A=alpha, B=beta, E=end of development. Examples: 2.23A8 3.4 | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modmSaStatHwVersion | 1.3.6.1.4.1.164.3.4.1.1.2.1.7 | ||
| Display String of the modem HW version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modmSaAlarmBuffTable | 1.3.6.1.4.1.164.3.4.1.1.3 | ||
| The alarm buffer of the Central and Remote Modems. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmSaAlarmBuffEntry | |||
| modmSaAlarmBuffEntry | 1.3.6.1.4.1.164.3.4.1.1.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmSaAlarmBuffEntry | |||
| modmSaAlarmBuffIndex | 1.3.6.1.4.1.164.3.4.1.1.3.1.1 | ||
| The index of the alarm buffer Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaAlarmBuffCode | 1.3.6.1.4.1.164.3.4.1.1.3.1.2 | ||
| The code of the alarm. For text description of each Alarm code see Modem's specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaAlarmBuffTime | 1.3.6.1.4.1.164.3.4.1.1.3.1.3 | ||
| The time stamp at which the alarm has occurred. The format is hh:mm:ss | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modmSaAlarmBuffState | 1.3.6.1.4.1.164.3.4.1.1.3.1.4 | ||
| The new status of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmSaParam | 1.3.6.1.4.1.164.3.4.1.1.4 | ||
| OBJECT IDENTIFIER | |||
| modmSaMode | 1.3.6.1.4.1.164.3.4.1.1.4.1 | ||
| The agent's current mode. For AMC 102 remote means regenerator. There can be some regenerators connecting one by the other. | |||
| OBJECT-TYPE | |||
| INTEGER | central(1), remote(2), remote2(3), remote3(4), remote4(5), remote5(6), remote6(7), remote7(8), remote8(9), remote9(10), remote10(11) | ||
| modmSaFarEndIpAddress | 1.3.6.1.4.1.164.3.4.1.1.4.2 | ||
| The IP address of the agent on the far end. If the Remote modem is NOT an agent, the variable will be 0.0.0.0. Set - will be enabled only to a Central modem that works as Proxy. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| modmSaFarEndType | 1.3.6.1.4.1.164.3.4.1.1.4.3 | ||
| The type of the Far-End modem. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), sa(2), card(3), saLowCost(4), hcdSa(5), hcdSaL(6), hcdCard(7), htu2Sa(8), htu2Card(9), htuE1Sa(10), htuE1SaL(11), htuE1Card(12), hcd4Sa(13), hcdPF(14), unmanaged(100) | ||
| modmSaRptrType | 1.3.6.1.4.1.164.3.4.1.1.4.4 | ||
| The Repeater between the Near and Far modem. none - no repeater exists between the modems. notApplicable - for modems that do not support this feature. | |||
| OBJECT-TYPE | |||
| INTEGER | none(2), hrpt(3), notApplicable(255) | ||
| modmSaLearnLineMode | 1.3.6.1.4.1.164.3.4.1.1.4.5 | ||
| This parameter is for the central unit only. Indicates if learn the regenerator order and number every time there is a fail in line or manually by user. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), manually(2), automatic(3) | ||
| modmSaNumOfUnits | 1.3.6.1.4.1.164.3.4.1.1.4.6 | ||
| This object will hold the number of regenerators in the line. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaRptrTable | 1.3.6.1.4.1.164.3.4.1.1.5 | ||
| The Repeaters parameters known to the central modem. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmSaRptrEntry | |||
| modmSaRptrEntry | 1.3.6.1.4.1.164.3.4.1.1.5.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmSaRptrEntry | |||
| modmSaIndex | 1.3.6.1.4.1.164.3.4.1.1.5.1.1 | ||
| A unique number to identify the modem that reports about the repeater. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaRptrIndex | 1.3.6.1.4.1.164.3.4.1.1.5.1.2 | ||
| The index of the Repeater. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmSaRptrTest | 1.3.6.1.4.1.164.3.4.1.1.5.1.3 | ||
| The possible loopbacks. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), loopLHrpt(2) | ||
| modmSaRptrActiveAlarms | 1.3.6.1.4.1.164.3.4.1.1.5.1.4 | ||
| Status of the Alarms. Each bit represents a specific alarm . For bit location of each alarm in the Octet String see modem's specification. If the value is 0 then there are No Alarms. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modmSaRptrAlrClear | 1.3.6.1.4.1.164.3.4.1.1.5.1.5 | ||
| Setting this attribute to on, clears all the active (On) alarms of the repeater. Upon completion, the value will automatically change to off(2).. | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| modmSaRptrVersion | 1.3.6.1.4.1.164.3.4.1.1.5.1.6 | ||
| SW/HW version of the repeater | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modmHub | 1.3.6.1.4.1.164.3.4.1.2 | ||
| OBJECT IDENTIFIER | |||
| modmHubParam | 1.3.6.1.4.1.164.3.4.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| modmHubTermConnect | 1.3.6.1.4.1.164.3.4.1.2.1.1 | ||
| Status: is the Terminal connected or not. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| modmHubController | 1.3.6.1.4.1.164.3.4.1.2.1.2 | ||
| Selection of Hub controller during normal operation. If 'terminal' is selected, NMS can still return control to itself by setting this object to 'nms'. While terminal is the controller, NMS can perform Get operations and Set trap masks. | |||
| OBJECT-TYPE | |||
| INTEGER | nms(1), terminal(2) | ||
| modmHubId | 1.3.6.1.4.1.164.3.4.1.2.1.3 | ||
| 4 Hex characters, identifying the Hub. The last two characters (least significant) will be displayed on the Hub's CL card by a 7 segment display. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| modmHubT1E1 | 1.3.6.1.4.1.164.3.4.1.2.1.4 | ||
| The T1/E1 value determines the Hub's clock rate. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), t1(2), e1(3) | ||
| modmHubClockSource | 1.3.6.1.4.1.164.3.4.1.2.1.5 | ||
| Clock source. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), external(2), internal(3), g703Section10(4), receive(5), station(6) | ||
| modmHubClockRate | 1.3.6.1.4.1.164.3.4.1.2.1.6 | ||
| Clock Rate in bps. The rates are the original T1/E1 rates or the rates divided by 2n. For modmHubT1E1=e1, instances (1)-(9) are applicable. For modmHubT1E1=t1, instances (31)-(36) are applicable. For modmHubT1E1=other, instance (255) is applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | e1r2048000(1), e1r1024000(2), e1r512000(3), e1r256000(4), e1r128000(5), e1r64000(6), e1r32000(7), e1r16000(8), e1r8000(9), t1r1544000(31), t1r772000(32), t1r386000(33), t1r193000(34), t1r96500(35), t1r48250(36), notApplicable(255) | ||
| modmHubIpMode | 1.3.6.1.4.1.164.3.4.1.2.1.7 | ||
| single - Upon BootP request from S-MOD, CM-2 will assign a 'private IP' (CM-2 IP + slot number of S-MOD), which will be applicable only between the S-MOD and CM-2. multi - CM-2 assigns up to 12/24 consequent IP addresses. One for each S-MOD according to the slot number. | |||
| OBJECT-TYPE | |||
| INTEGER | single(1), multi(2) | ||
| modmHubInstallation | 1.3.6.1.4.1.164.3.4.1.2.1.8 | ||
| The string will be a multiple set of 16 bit corresponds to its card position, and each set corresponds to a modem, where set #1 is the first modem on each card, and set n is the n-st modem in each card. 1........10.....16|1........10.....16| modem 1 | modem 2 | MSB LSB Bits 1-3 and 16 will be ignored. For LRS-52 detailed bit assignment see product's spec. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modmHubAlarms | 1.3.6.1.4.1.164.3.4.1.2.2 | ||
| OBJECT IDENTIFIER | |||
| modmHubActiveAlarms | 1.3.6.1.4.1.164.3.4.1.2.2.1 | ||
| Status of the Alarms for each Slot. Each bit represents a Slot of the Hub. For bit location of each Alarm in the Octet String see Hub's specification. A bit is '1' (On) if at least one 'On' alarm exists for this Slot. If the value is 0 then there are No 'On' Alarms in any Slot. For LRS52 - read 'modem' instead of the word 'slot' | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modmHubAlrClear | 1.3.6.1.4.1.164.3.4.1.2.2.2 | ||
| Setting this attribute to on, clears all the active (On) alarms of the Hub. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmHubMaskAlarms | 1.3.6.1.4.1.164.3.4.1.2.2.3 | ||
| Mask of Alarms per Slot. Each bit represents a Slot of the Hub. For bit location of each Slot in the Octet String see Hub's specification (same as modmHubActiveAlarms). When a bit is '1' (On) it is masked ; all alarms of this Slot should not be sent and Alarm LED should not be lit. This mask overrides the mask on the specific alarms of each Slot or modem. If the value is 0 then all alarms should be sent. For LRS52 - read 'modem' instead of the word 'slot'. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modmMdl | 1.3.6.1.4.1.164.3.4.2 | ||
| OBJECT IDENTIFIER | |||
| modmMdlParam | 1.3.6.1.4.1.164.3.4.2.1 | ||
| OBJECT IDENTIFIER | |||
| mdlParamTable | 1.3.6.1.4.1.164.3.4.2.1.1 | ||
| Parameters table of cards in the Hub. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlParamEntry | |||
| mdlParamEntry | 1.3.6.1.4.1.164.3.4.2.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlParamEntry | |||
| mdlSIdx | 1.3.6.1.4.1.164.3.4.2.1.1.1.1 | ||
| A unique number to identify a slot position in the modems Hub. | |||
| OBJECT-TYPE | |||
| INTEGER | psA(1), psB(2), cl(3), io1(4), io2(5), io3(6), io4(7), io5(8), io6(9), io7(10), io8(11), io9(12), io10(13), io11(14), io12(15) | ||
| mdlSNoOfModems | 1.3.6.1.4.1.164.3.4.2.1.1.1.2 | ||
| Number of modems on this card. 255 = notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlCardType | 1.3.6.1.4.1.164.3.4.2.1.1.1.3 | ||
| Card's type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), empty(2), ps48V(3), ps110V(4), ps230V(5), cm2(6), smod(7), asmi24(8), asmi31(9), asmi32(10), asmi50(11), mtmi20(12), fomi40(13), fomiE1T1(14), asm40cd(15), asmi50cd(16), fomi40cd(17), fomiE1T1cd(18), ps110V-24(19), ps230V-24(20), ps48V-24(21), asmi31cq(22), asmi51cq(23), asmi51cd(24), asmi52cd(25), asmi52cq(26), fomiE3(51), fomiT3(52), optimux4E1(53), optimux4T1(54), amc102(55), notApplicable(255) | ||
| mdlSPanelType | 1.3.6.1.4.1.164.3.4.2.1.1.1.4 | ||
| LRS-12 Card connectors' panel type. fx - IMOD panels psxxx - PS panels fxCm2 - CM-2 panels. | |||
| OBJECT-TYPE | |||
| INTEGER | empty(1), f2(2), f3(3), f5(5), f6(6), f7(7), f9(9), f10(10), f11(11), f12(12), f13(13), f14(14), f18(15), f19(16), f22(17), f20(18), f21(19), f23(20), fO1(21), fO2(22), fO3(23), fO4(24), fO5(25), fO6(26), fO7(27), fO8(28), fO9(29), fO10(30), fO11(31), fO12(32), fO13(33), fO14(34), fO15(35), fO16(36), fO17(37), fO18(38), fO19(39), fO20(40), fO21(41), fO22(42), ps230And115(81), psp230And115(82), ps48(83), psp48(84), f1Cm2(91), f2Cm2(92), f3Cm2(93), f4Cm2(94), f5Cm2(95), f1Cm2New(96), notApplicable(255) | ||
| mdlSLed | 1.3.6.1.4.1.164.3.4.2.1.1.1.5 | ||
| LEDs status on the card . Each led will be represented by 4 bits where the first 2 bits (left) will specify the Status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the Color : (00=GREEN, 01=RED, 10=YELLOW, 11=ORANGE). This object is not applicable for the 'smod', 'empty' and 'unknown' card types. For them 0 will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlSActiveAlarms | 1.3.6.1.4.1.164.3.4.2.1.1.1.6 | ||
| This object is applicable only for PS and CL cards. It gives the status of the Alarms for each Slot. Each bit represents an alarm in the slot. For bit location of each Alarm in the Octet String see Hub's specification. A bit is '1' if the alarm is On. If the value is 0 then there are No 'On' Alarms in the Slot. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlAlrClear | 1.3.6.1.4.1.164.3.4.2.1.1.1.7 | ||
| Setting this attribute to on, clears all the active (On) alarms of the Slot. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| mdlSConfigMismatch | 1.3.6.1.4.1.164.3.4.2.1.1.1.8 | ||
| This object is applicable only for slots containing IMOD cards. ON - when CM-2 realizes that the configuration of the Near-End modem1 is different from that of its Far-End modem. In this case it expects user to decide which of the modems' configuration is the correct one (by 'mdlConfigSource'), or change the incorrect modem configuration. When one of these conditions is fulfilled, the value will automatically turn to OFF. Applicable for a single modem. Line1 - The same as for ON but for modem-1 line. Applicable for a double modem. Line2 - The same as for ON but for modem-2 line. Applicable for a double modem. OFF - Near-End and Far-End modems have the same configuration (OK). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), line1(4), line2(5), notApplicable(255) | ||
| mdlConfigSource | 1.3.6.1.4.1.164.3.4.2.1.1.1.9 | ||
| This object is applicable only for slots containing IMOD cards, when mdlSConfigMismatch=on/on1/on2. nearEnd - Near End - 1 modem has the correct configuration farEnd - Far End - 1 has the correct configuration nearEnd - Near End - 2 has the correct configuration farEnd - Far End - 2 has the correct configuration. | |||
| OBJECT-TYPE | |||
| INTEGER | nearEnd(1), farEnd(2), nearEnd2(3), farEnd2(4), notApplicable(255) | ||
| mdlConfigGround | 1.3.6.1.4.1.164.3.4.2.1.1.1.10 | ||
| Enables to connect or disconnect an IMOD card to the ground. disconnect - not connected to ground. connect - connected to ground. notApplicable - for other cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disconnect(2), connect(3) | ||
| modem | 1.3.6.1.4.1.164.3.4.3 | ||
| OBJECT IDENTIFIER | |||
| modemParam | 1.3.6.1.4.1.164.3.4.3.1 | ||
| OBJECT IDENTIFIER | |||
| modemParamTable | 1.3.6.1.4.1.164.3.4.3.1.1 | ||
| This parameters table is applicable only for modems that are not agents. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModemParamEntry | |||
| modemParamEntry | 1.3.6.1.4.1.164.3.4.3.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModemParamEntry | |||
| modemIdx | 1.3.6.1.4.1.164.3.4.3.1.1.1.1 | ||
| For LRS: A unique number to identify a modem in the Hub or its far-end modem. For DXC: This will be the ifIndex of the External Port of DSL16 card, that works with this modem/product. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemType | 1.3.6.1.4.1.164.3.4.3.1.1.1.2 | ||
| Modem type. xxxxxx - Stand-Alone modem. xxxxxxc - Modem on a Card within a Hub having an Agent. xxxxxxr - Modem on a Card within a Hub having no Agent. xxxxxxcd - Modem on a Double-Modem Card within a Hub having an Agent. Each modem has it's own CPU. xxxxxxcq - Modem on a Quad-Modem Card within a Hub having an Agent. One CPU for all modems. lrs52 - Modem within the LRS-52 device. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), asmi24c(2), asmi31c(3), asmi32c(4), asmi50c(5), mtmi20c(6), fomi40c(7), fomiE1T1c(8), asm40cd(9), asmi31cq(10), asmi51cq(11), asmi51cd(12), asmi52cq(13), asmi52cd(14), asmi24r(22), asmi31r(23), asmi32r(24), asmi50r(25), mtmi20r(26), asmi24(42), asmi31(43), asmi32(44), asmi50(45), mtmi20(46), fomi40(47), fomiE1T1(48), asmi51(49), asmi52S(50), asmi52M(51), lrs52(71) | ||
| modemConfigMode | 1.3.6.1.4.1.164.3.4.3.1.1.1.3 | ||
| The mode identifies if the Modem operates as the Master unit or as the Slave unit. For modems having a jumper for this function, this object will be RO. This object can be Set only to the Master unit when modemModeTemporary=no (the Far-End unit will receive its new mode from the Central unit, via management link between the modems). Regarding other objects (except modemModeTemporary): If Modem is Master, it can perform RW operations for both Master and Slave modem. If Modem is Slave, it can perform RO operations for both Master and Slave modem. | |||
| OBJECT-TYPE | |||
| INTEGER | master(1), slave(2) | ||
| modemModeTemporary | 1.3.6.1.4.1.164.3.4.3.1.1.1.4 | ||
| This object specifies if the Modem operates as modemConfigMode value (Master/Slave) temporarily or permanently. This object can be Set only when: - modemConfigMode=master AND modemModeTemporary=no - modemConfigMode=slave AND modemModeTemporary=yes this is an exception to the fact that all other objects in this case are RO. The other unit will receive its value for this object from the Set unit, via management link between the modems. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| modemNoOfDte | 1.3.6.1.4.1.164.3.4.3.1.1.1.5 | ||
| Number of DTE ports in the modem. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemWire | 1.3.6.1.4.1.164.3.4.3.1.1.1.6 | ||
| Modem wiring. | |||
| OBJECT-TYPE | |||
| INTEGER | w2wire(1), w4wire(2), notApplicable(255) | ||
| modemMngLink | 1.3.6.1.4.1.164.3.4.3.1.1.1.7 | ||
| Communication status between the pair of modems. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modemReset | 1.3.6.1.4.1.164.3.4.3.1.1.1.8 | ||
| When this object is set to the value of hwReset(3), the module performs HW Reset. When this object is set to the value of configReset(4), the modem performs Configuration Reset, which will set the modem to the last parameters it was configured. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), hwReset(3), configReset(4) | ||
| modemSlot | 1.3.6.1.4.1.164.3.4.3.1.1.1.9 | ||
| A unique number to identify the slot position of the modem (card)in its Hub. notApplicable - for a stand-alone modem or Rack 214 card. io13..io15 - are for DXC use in case of a Far-Unit that is DSL16 card. | |||
| OBJECT-TYPE | |||
| INTEGER | io1(4), io2(5), io3(6), io4(7), io5(8), io6(9), io7(10), io8(11), io9(12), io10(13), io11(14), io12(15), io13(16), io14(17), io15(18), notApplicable(255) | ||
| modemHubId | 1.3.6.1.4.1.164.3.4.3.1.1.1.10 | ||
| 4 Hex characters, identifying the Hub. The last two characters (least significant) will be displayed on the Hub's CL card by a 7 segment display. This object is applicable only for LRS-12 modems. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| modemIpAddress | 1.3.6.1.4.1.164.3.4.3.1.1.1.11 | ||
| For LRS: The IP address of the LRS-12 agent . If the modem is NOT an LRS-12 card, the variable will be 0.0.0.0. For DXC: the IP Address of the Far-End unit. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| modemPsType | 1.3.6.1.4.1.164.3.4.3.1.1.1.12 | ||
| The type of PS, for a stand-alone modem. notApplicable - for LRS-12 or Rack 214 card. | |||
| OBJECT-TYPE | |||
| INTEGER | ac(1), dc(2), notApplicable(255) | ||
| modemMaskTraps | 1.3.6.1.4.1.164.3.4.3.1.1.1.13 | ||
| The value determines the modem traps the agent should mask and not send to the management console. The value is a sum of 2**n, where n is a bit assigned to a certain trap. For bit assignment see modem's specification. Value of '0', means that no trap should be masked. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemActiveAlarms | 1.3.6.1.4.1.164.3.4.3.1.1.1.14 | ||
| Status of the Alarms for each modem. Each bit represents an alarm. For bit location of each Alarm in the Octet String see modem's specification. A bit is '1' if the alarm is On. If the value is 0 then there are no 'On' alarms on this modem. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modemAlrClear | 1.3.6.1.4.1.164.3.4.3.1.1.1.15 | ||
| Setting this attribute to on, clears all the active (On) alarms of the modem. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modemAlrBufClear | 1.3.6.1.4.1.164.3.4.3.1.1.1.16 | ||
| Setting this attribute to on, clears all the alarms in the buffer alarm of the modem. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modemMaskSignaling | 1.3.6.1.4.1.164.3.4.3.1.1.1.17 | ||
| Mask of Signals per modem. When a signal is masked, the agent will not send the modemSignalingChange TRAP, upon change of this signal's value and it will not enter the History Log. Each bit represents a signal of the modem. For bit location of each signal in the Octet String see modem's specification. When a bit is '1' (On) it is masked . | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modemPanelType | 1.3.6.1.4.1.164.3.4.3.1.1.1.18 | ||
| The panel type of the modem. This parameter is applicable only for Far-End modems that are stand-alone or cards of another LRS-12. It enables displaying the correct panel of the modem. - Stand-alone : applicable only for ASMi-24 and ASMi-50 modems. pcu - with connector for Portable Control Unit lcd - LCD display and buttons. - LRS-12 card : fx is the connectors panel of the modem. | |||
| OBJECT-TYPE | |||
| INTEGER | f2(2), f3(3), f7(7), f9(9), f10(10), f11(11), f12(12), fO1(21), fO2(22), fO3(23), fO4(24), fO5(25), fO6(26), fO7(27), fO8(28), fO9(29), fO10(30), pcu(101), lcd(102), notApplicable(255) | ||
| modemIType | 1.3.6.1.4.1.164.3.4.3.1.1.1.19 | ||
| Is the modem Intelligent (ASMi-xx) ; or not - (ASM-xx). This object is used only for the Far-End modem (with the relevant modemIdx). notApplicable - for ASMi-32, ASMi-50 no - modem is NOT I-Type so it doesn't have a management link to its pair-modem. yes - modem is I-Type so it has a management link to its pair-modem. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| modemRcvPower | 1.3.6.1.4.1.164.3.4.3.1.1.1.20 | ||
| The Rx Level of the modem, in dBm. Valid values: -99 .. 0. 255=not applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemSwVersion | 1.3.6.1.4.1.164.3.4.3.1.1.1.21 | ||
| SW version of the modem, multiplied by 100. Example: 115 means SW ver: 1.15 0 = notApplicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemLed | 1.3.6.1.4.1.164.3.4.3.1.1.1.22 | ||
| LEDs status on the card . Each led will be represented by 4 bits where the first 2 bits (left) will specify the Status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the Color : (00=GREEN, 01=RED, 10=YELLOW, 11=ORANGE). This object is applicable for modems located on a card that contains more than one modem. When not applicable 0 will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modemRemoteType | 1.3.6.1.4.1.164.3.4.3.1.1.1.23 | ||
| Remote modem card type. Not applicable to near - end modems. For LRS-52, sa(3)=saMaster. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unknown(2), sa(3), single(4), double(5), rack(6), quad(7), saSlave(8), fcd(9), dxcCard4p(10), dxcCard8p(11), lrs52(12) | ||
| modemConfigPhantom | 1.3.6.1.4.1.164.3.4.3.1.1.1.24 | ||
| Enables to supply electric power to remote devices (SA modem, repeaters), through the current module. off - remote devices will not get PS through the current modem. on - remote devices will get PS through the current modem. notApplicable - for a modem without a phantom unit. notValid - In case the unit exists but is not functioning. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3), notValid(4) | ||
| modemRemoteTestEnable | 1.3.6.1.4.1.164.3.4.3.1.1.1.25 | ||
| This parameter identifies if the remote Modem allowed to operates tests. For Near-End modems this parameter will be ON. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| modemSwVerString | 1.3.6.1.4.1.164.3.4.3.1.1.1.26 | ||
| Display String of the modem SW version. Format: X. Y Z P 0..9 0..99 A,B,E 0..99 (Z+P are optional.) A=alpha, B=beta, E=end of development. Examples: 2.23A8 3.4 | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modemRemoteIdx | 1.3.6.1.4.1.164.3.4.3.1.1.1.27 | ||
| 0 = notApplicable. For LRS: The Remote modem index. Applicable only for modemRemoteType=double(5) or quad(7). For DXC and LRS-52: - if Remote unit is an LRS Quad card: remote modem index (1..4) - if Remote unit is a DXC DSL16 card: external port index (1..16). - if Remote unit is an LRS-52 modem: 1..24. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemHwVerString | 1.3.6.1.4.1.164.3.4.3.1.1.1.28 | ||
| Display String of the modem HW version. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modemResetStatistics | 1.3.6.1.4.1.164.3.4.3.1.1.1.29 | ||
| In the on state all statistics counters (including E1 counters) are zeroed. Upon completion, the value will automatically change to off(2). notApplicable - for modems with no statistics support. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| modemMaxRate | 1.3.6.1.4.1.164.3.4.3.1.1.1.30 | ||
| Maximum rate supported by the modem | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r2Mbps(2), r4Mbps(3) | ||
| modemBoxMaterial | 1.3.6.1.4.1.164.3.4.3.1.1.1.31 | ||
| Shape (picture) of modem box is related to box material. Applicable for ASMi52 SA | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), plastic(2), metal(3) | ||
| modemAlrBuffer | 1.3.6.1.4.1.164.3.4.3.2 | ||
| OBJECT IDENTIFIER | |||
| modemAlrBufTable | 1.3.6.1.4.1.164.3.4.3.2.1 | ||
| This parameters table is applicable only for modems that are not agents. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModemAlrBufEntry | |||
| modemAlrBufEntry | 1.3.6.1.4.1.164.3.4.3.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModemAlrBufEntry | |||
| modemAlrBufIdx | 1.3.6.1.4.1.164.3.4.3.2.1.1.1 | ||
| Running index of the alarm buffer table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemAlrBufCode | 1.3.6.1.4.1.164.3.4.3.2.1.1.2 | ||
| The code of the alarm. For text description of each Alarm code see Modem's specification. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modemAlrBufState | 1.3.6.1.4.1.164.3.4.3.2.1.1.3 | ||
| The new status of the alarm. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modemAlrBufDate | 1.3.6.1.4.1.164.3.4.3.2.1.1.4 | ||
| The Date at which the alarm has occurred. The format is according to the entered systemDate format. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modemAlrBufTime | 1.3.6.1.4.1.164.3.4.3.2.1.1.5 | ||
| The time stamp at which the alarm has occurred. The format is hh:mm:ss | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modemAlrBufSysUpTime | 1.3.6.1.4.1.164.3.4.3.2.1.1.6 | ||
| The value of sysUpTime at the time the alarm has occurred. This object is applicable only for products that cannot support calendar date (modemAlrBufDate) and time (modemAlrBufTime) When not applicable, this object contains a zero value | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| modemStatistics | 1.3.6.1.4.1.164.3.4.3.3 | ||
| OBJECT IDENTIFIER | |||
| modemGeneralTable | 1.3.6.1.4.1.164.3.4.3.3.1 | ||
| The IMOD General data Table. The data is specific to each modem. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModemGeneralEntry | |||
| modemGeneralEntry | 1.3.6.1.4.1.164.3.4.3.3.1.1 | ||
| An entry in the modemGeneralTable. This entry is per modem. Each modem has a specific index, which identifies it. | |||
| OBJECT-TYPE | |||
| ModemGeneralEntry | |||
| modemCurrentElapsedTime | 1.3.6.1.4.1.164.3.4.3.3.1.1.1 | ||
| The number of seconds that have elapsed since the beginning of the current error-measurement period. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..899 | ||
| modemValidIntervals | 1.3.6.1.4.1.164.3.4.3.3.1.1.2 | ||
| The number of previous intervals for which data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..96 | ||
| modemIntervalTable | 1.3.6.1.4.1.164.3.4.3.3.2 | ||
| The IMOD Interval Table. The data is specific to each modem. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModemIntervalEntry | |||
| modemIntervalEntry | 1.3.6.1.4.1.164.3.4.3.3.2.1 | ||
| An entry in the modemIntervalTable. This entry is per modem and per interval selected. | |||
| OBJECT-TYPE | |||
| ModemIntervalEntry | |||
| modemIntervalNumber | 1.3.6.1.4.1.164.3.4.3.3.2.1.1 | ||
| The number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). Maximum valid number is modemValidIntervals. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..96 | ||
| modemSyncLoss | 1.3.6.1.4.1.164.3.4.3.3.2.1.2 | ||
| Percent of interval, SyncLoss signal is ON. 101 = notApplicable/unknown. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..101 | ||
| modemLineQuality | 1.3.6.1.4.1.164.3.4.3.3.2.1.3 | ||
| Quality of Line for the selected modem, in the selected valid interval. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), bad(2), mid(3), good(4), unknown(5), syncLoss(6) | ||
| modemLineUtility | 1.3.6.1.4.1.164.3.4.3.3.2.1.4 | ||
| Percent of interval, Line is utilized. 101 = notApplicable/unknown. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..101 | ||
| modemRTS | 1.3.6.1.4.1.164.3.4.3.3.2.1.5 | ||
| Percent of interval, RTS signal is ON. 101 = notApplicable/unknown. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..101 | ||
| modemCD | 1.3.6.1.4.1.164.3.4.3.3.2.1.6 | ||
| Percent of interval, CD signal is ON. 101 = notApplicable/unknown. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..101 | ||
| modemBertResult | 1.3.6.1.4.1.164.3.4.3.3.2.1.7 | ||
| Result of BERT for the selected modem, in the selected valid interval. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modemBpvError | 1.3.6.1.4.1.164.3.4.3.3.2.1.8 | ||
| BPV Error. The Octet will be built as follows: MSB 7 6 5 4 3 2 1 0 LSB |__| |______________| y=0..3 x=0..63 BPV Error = x * (10**y) An Agent that does not support this object will send Size=0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1) | ||
| modemFoError | 1.3.6.1.4.1.164.3.4.3.3.2.1.9 | ||
| FO Error. The Octet will be built as follows: MSB 7 6 5 4 3 2 1 0 LSB |__| |______________| y=0..3 x=0..63 FO Error = x * (10**y) An Agent that does not support this object will send Size=0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1) | ||
| modmPrt | 1.3.6.1.4.1.164.3.4.4 | ||
| OBJECT IDENTIFIER | |||
| modmSpPort | 1.3.6.1.4.1.164.3.4.4.1 | ||
| OBJECT IDENTIFIER | |||
| modmPrtSpTable | 1.3.6.1.4.1.164.3.4.4.1.1 | ||
| Configuration parameters of the Local or Remote Modem Supervisory Ports. The port will be identified by its specific ifIndex value. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtSpEntry | |||
| modmPrtSpEntry | 1.3.6.1.4.1.164.3.4.4.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmPrtSpEntry | |||
| modmPrtSpUsage | 1.3.6.1.4.1.164.3.4.4.1.1.1.1 | ||
| This attribute indicates what is the usage of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | nmsSlip(2), terminal(3), agentSlip(4), nmsPpp(5), agentPpp(6) | ||
| modmPrtSpRate | 1.3.6.1.4.1.164.3.4.4.1.1.1.2 | ||
| This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), s300bps(2), s1200bps(3), s2400bps(4), s4800bps(5), s9600bps(6) | ||
| modmPrtSpDataBits | 1.3.6.1.4.1.164.3.4.4.1.1.1.3 | ||
| This attribute indicates the number of data bits in the word format. | |||
| OBJECT-TYPE | |||
| INTEGER | dataBits7(1), dataBits8(2) | ||
| modmPrtSpParity | 1.3.6.1.4.1.164.3.4.4.1.1.1.4 | ||
| This attribute indicates the parity mode in async frame | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), odd(2), even(3) | ||
| modmPrtSpInterface | 1.3.6.1.4.1.164.3.4.4.1.1.1.5 | ||
| This attribute indicates the supervisory port interface. dce - the modem appears as a DCE for the SP port. dte - the modem operates as a DTE, for connection via modem, for the SP port. | |||
| OBJECT-TYPE | |||
| INTEGER | dce(1), dte(2) | ||
| modmPrtSpCTS | 1.3.6.1.4.1.164.3.4.4.1.1.1.6 | ||
| CTS line state. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), rts(3) | ||
| modmPrtSpDcdDelay | 1.3.6.1.4.1.164.3.4.4.1.1.1.7 | ||
| DCD delay in msec. d10 = delay of 10msec. | |||
| OBJECT-TYPE | |||
| INTEGER | d0(2), d10(3), d50(4), d100(5), d200(6), d300(7) | ||
| modmPrtSpDsr | 1.3.6.1.4.1.164.3.4.4.1.1.1.8 | ||
| DSR line state. | |||
| OBJECT-TYPE | |||
| INTEGER | on(2), dtr(3) | ||
| modmDs1Port | 1.3.6.1.4.1.164.3.4.4.2 | ||
| OBJECT IDENTIFIER | |||
| modmPrtDs1Table | 1.3.6.1.4.1.164.3.4.4.2.1 | ||
| Statistics parameters of the Local and Remote modem Ds1 ports. The port will be identified by its specific ifIndex value. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtDs1Entry | |||
| modmPrtDs1Entry | 1.3.6.1.4.1.164.3.4.4.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmPrtDs1Entry | |||
| modmPrtDs1HdslPriorityBumping | 1.3.6.1.4.1.164.3.4.4.2.1.1.1 | ||
| The 4 bytes represent the 32 time slots of the E1 frame. Each bit can be set to one, making the corresponding time slot a HIGH priority. Bits 16 and 32 cannot be modified by the user. The maximum number of HIGH priority time slots is 16. The default value is LOW, i.e., 0. This variable is RO in the Remote unit. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| modmPrtDs1Sync | 1.3.6.1.4.1.164.3.4.4.2.1.1.2 | ||
| The standard used for the time required for the E1 port to return to normal operation after local loss of synchronization. Default: itu(2). | |||
| OBJECT-TYPE | |||
| INTEGER | itu(2), fast(3), s62411(4) | ||
| modmPrtDs1BpvLastMin | 1.3.6.1.4.1.164.3.4.4.2.1.1.3 | ||
| This object is applicable only for an E1 active port. It provides the number of BPV (BiPolar Violation) events detected during the last minute. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtDs1BpvMax | 1.3.6.1.4.1.164.3.4.4.2.1.1.4 | ||
| This object is applicable only for an E1 active port. It provides the maximal number of BPV (BiPolar Violation) events (per minute), detected during the worst minute. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtDs1LineLength | 1.3.6.1.4.1.164.3.4.4.2.1.1.5 | ||
| This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft 'fcc68' - provides compliance with the FCC 68.308 Option A output pulse mask. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), fcc68(7), notApplicable(255) | ||
| modmPrtDs1CRCAvgError | 1.3.6.1.4.1.164.3.4.4.2.1.1.6 | ||
| Counts the average number of CRC error events per second. The average is updated every second | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmHdslPort | 1.3.6.1.4.1.164.3.4.4.3 | ||
| OBJECT IDENTIFIER | |||
| modmPrtHdslCurrentTable | 1.3.6.1.4.1.164.3.4.4.3.1 | ||
| The HDSL Current Table. The data collected is for the current 15-minute interval. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtHdslCurrentEntry | |||
| modmPrtHdslCurrentEntry | 1.3.6.1.4.1.164.3.4.4.3.1.1 | ||
| An entry in the HDSL Current Table. This entry is per HDSL interface (LOOP1 or LOOP2). Each modem (Central/Remote) has a specific ifIndex value for the port, which identifies it. | |||
| OBJECT-TYPE | |||
| ModmPrtHdslCurrentEntry | |||
| modmPrtHdslCurrentElapsedTime | 1.3.6.1.4.1.164.3.4.4.3.1.1.1 | ||
| The number of seconds that have elapsed since the beginning of the current error-measurement period. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..899 | ||
| modmPrtHdslCurrentESs | 1.3.6.1.4.1.164.3.4.4.3.1.1.2 | ||
| The number of Errored Seconds encountered by an HDSL interface in the current 15 minute interval. An Errored Second is any second containing one or more Errored Blocks or an occurrence of an SDP. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslCurrentSESs | 1.3.6.1.4.1.164.3.4.4.3.1.1.3 | ||
| The number of Severely Errored Seconds encountered by an HDSL interface in the current 15 minute interval. An SES is any second containing more than 30% Errored Blocks (50 blocks) or one or more SDPs. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslCurrentBBEs | 1.3.6.1.4.1.164.3.4.4.3.1.1.4 | ||
| The number of Background Block Errors encountered by an HDSL interface in the current 15 minute interval. A BBE is an errored block not occurring as part of an SES. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslCurrentUASs | 1.3.6.1.4.1.164.3.4.4.3.1.1.5 | ||
| The number of Unavailable Seconds encountered by an HDSL interface in the current 15 minute interval. A UAS is any second in which a failed signal state exists. A failure state is declared when 10 consecutive SESs occur, and is cleared after 10 consecutive seconds free of an SES. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslCurrentNoiseMargin | 1.3.6.1.4.1.164.3.4.4.3.1.1.6 | ||
| The current noise margin in DB. This object is not an accumulative one, therefore it's value will appear only in this table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtHdslCurrentAttenuation | 1.3.6.1.4.1.164.3.4.4.3.1.1.7 | ||
| The current attenuation in DB. This object is not an accumulative one, therefore it's value will appear only in this table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtHdslIntervalTable | 1.3.6.1.4.1.164.3.4.4.3.2 | ||
| The HDSL Interval Table. The data collected is for the last 96 completed 15-minute intervals. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtHdslIntervalEntry | |||
| modmPrtHdslIntervalEntry | 1.3.6.1.4.1.164.3.4.4.3.2.1 | ||
| An entry in the HDSL Interval Table. This entry is per an HDSL interface (LOOP1 or LOOP2) and per 15 minute interval. The port and unit (Central/Remote) is identified by its specific ifIndex value. | |||
| OBJECT-TYPE | |||
| ModmPrtHdslIntervalEntry | |||
| modmPrtHdslIntervalNumber | 1.3.6.1.4.1.164.3.4.4.3.2.1.1 | ||
| The number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..96 | ||
| modmPrtHdslIntervalESs | 1.3.6.1.4.1.164.3.4.4.3.2.1.2 | ||
| The number of Errored Seconds encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslIntervalSESs | 1.3.6.1.4.1.164.3.4.4.3.2.1.3 | ||
| The number of Severely Errored Seconds encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslIntervalBBEs | 1.3.6.1.4.1.164.3.4.4.3.2.1.4 | ||
| The number of Background Block Errors encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslIntervalUASs | 1.3.6.1.4.1.164.3.4.4.3.2.1.5 | ||
| The number of Unavailable Seconds encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslIntervalESR | 1.3.6.1.4.1.164.3.4.4.3.2.1.6 | ||
| The ratio of ESs to 900 seconds, encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| modmPrtHdslIntervalSESR | 1.3.6.1.4.1.164.3.4.4.3.2.1.7 | ||
| The ratio of SESs to 900 seconds, encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| modmPrtHdslIntervalBBER | 1.3.6.1.4.1.164.3.4.4.3.2.1.8 | ||
| The ratio of BBEs to 900 seconds, encountered by an HDSL interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| modmPrtHdslTotalTable | 1.3.6.1.4.1.164.3.4.4.3.3 | ||
| The HDSL Total Table. The data collected is the cumulative sum of the various statistics for the 24 hour period preceding the current interval. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtHdslTotalEntry | |||
| modmPrtHdslTotalEntry | 1.3.6.1.4.1.164.3.4.4.3.3.1 | ||
| An entry in the HDSL Total Table. This entry is per an HDSL interface (LOOP1 or LOOP2). The port and unit (Central/Remote) is identified by its specific ifIndex value. | |||
| OBJECT-TYPE | |||
| ModmPrtHdslTotalEntry | |||
| modmPrtHdslTotalValidIntervals | 1.3.6.1.4.1.164.3.4.4.3.3.1.1 | ||
| The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the interface has been online. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..96 | ||
| modmPrtHdslTotalESs | 1.3.6.1.4.1.164.3.4.4.3.3.1.2 | ||
| The number of Errored Seconds encountered by an HDSL interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslTotalSESs | 1.3.6.1.4.1.164.3.4.4.3.3.1.3 | ||
| The number of Severely Errored Seconds encountered by an HDSL interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslTotalBBEs | 1.3.6.1.4.1.164.3.4.4.3.3.1.4 | ||
| The number of Background Block Errors encountered by an HDSL interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslTotalUASs | 1.3.6.1.4.1.164.3.4.4.3.3.1.5 | ||
| The number of Unavailable Seconds encountered by an HDSL interface in the previous 24 hour interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| modmPrtHdslTable | 1.3.6.1.4.1.164.3.4.4.3.4 | ||
| The HDSL Table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtHdslEntry | |||
| modmPrtHdslEntry | 1.3.6.1.4.1.164.3.4.4.3.4.1 | ||
| An entry in the HDSL Table. The port and unit (Central/Remote) is identified by its specific modmPrtHdslIndex value. | |||
| OBJECT-TYPE | |||
| ModmPrtHdslEntry | |||
| modmPrtHdslIndex | 1.3.6.1.4.1.164.3.4.4.3.4.1.1 | ||
| The HDSL port index. In some cases it can equal ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtHdslDedicatedTs | 1.3.6.1.4.1.164.3.4.4.3.4.1.2 | ||
| The HDSL Current Dedicated TS. Valid values: 0..31. 255 = None (no dedicated TS). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| modmPrtHdslPriorityBumping | 1.3.6.1.4.1.164.3.4.4.3.4.1.3 | ||
| The 4 bytes represent time slots 0..31 of the E1 frame. Each bit can be set to '1', making the corresponding time slot a HIGH priority. Bit 0 is always HIGH (cannot be modified by the user). The maximum number of HIGH priority time slots is: 16 for E1 ; 13 for T1 (including TS0). The default value is LOW, i.e., 0. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| modmPrtHdslMngProtocol | 1.3.6.1.4.1.164.3.4.4.3.4.1.4 | ||
| A unique number to identify an Inband management over the link. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), dedicatedTs(4), dedicatedPpp(5), dedicatedFr(6) | ||
| modmPrtHdslRoutProtocol | 1.3.6.1.4.1.164.3.4.4.3.4.1.5 | ||
| Inband Mng Routing Protocol of the port. When modmPrtHdslMngProtocol is 'dedicatedPpp'-'proprietary' and 'rip2' are applicable. For other values - only 'proprietary' is applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| modmPrtHdslInbandMngRate | 1.3.6.1.4.1.164.3.4.4.3.4.1.6 | ||
| A unique number to identify the rate of the Inband management. It is applicable only when modmPrtHdslDedicatedTs <> (255 Or 0). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r4k(2), r8k(3), r12k(4), r16k(5), r32k(6), r64k(7) | ||
| modmDtePort | 1.3.6.1.4.1.164.3.4.4.4 | ||
| OBJECT IDENTIFIER | |||
| modmPrtDteTable | 1.3.6.1.4.1.164.3.4.4.4.1 | ||
| Configuration parameters of the Master and Slave Modem DTE Ports. The port and unit (Master/Slave) is identified by its specific modmPrtDteIndex value. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtDteEntry | |||
| modmPrtDteEntry | 1.3.6.1.4.1.164.3.4.4.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmPrtDteEntry | |||
| modmPrtDteIndex | 1.3.6.1.4.1.164.3.4.4.4.1.1.1 | ||
| The DTE port index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtDteProtocol | 1.3.6.1.4.1.164.3.4.4.4.1.1.2 | ||
| The DTE port Protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(2), async(3) | ||
| modmPrtDteDataBits | 1.3.6.1.4.1.164.3.4.4.4.1.1.3 | ||
| The DTE number of data bits. | |||
| OBJECT-TYPE | |||
| INTEGER | dataBits6(1), dataBits7(2), dataBits8(3), dataBits9(4), dataBits10(5), dataBits11(6), dataBits5(7) | ||
| modmPrtDteStopBits | 1.3.6.1.4.1.164.3.4.4.4.1.1.4 | ||
| The DTE minimum number of stop bits in the tx async frame. | |||
| OBJECT-TYPE | |||
| INTEGER | stopBits1Bit(1), stopBits1dot5Bits(2), stopBits2Bits(3) | ||
| modmPrtDteRate | 1.3.6.1.4.1.164.3.4.4.4.1.1.5 | ||
| The DTE port rate. | |||
| OBJECT-TYPE | |||
| INTEGER | r300bps(1), r600bps(2), r1200bps(3), r2400bps(4), r4800bps(5), r9600bps(6), r14400bps(7), r16000bps(8), r19200bps(9), r28800bps(10), r32000bps(11), r38400bps(12), r48000bps(13), r56000bps(14), r57600bps(15), r64000bps(16), r72000bps(17), r96000bps(18), r112000bps(19), r115200bps(20), r128Kbps(21), r144Kbps(22), r192Kbps(23), r256Kbps(24), r320Kbps(25), r384Kbps(26), r448Kbps(27), r512Kbps(28), r576Kbps(29), r640Kbps(30), r704Kbps(31), r768Kbps(32), r1024Kbps(33), r1536Kbps(34), r1544Kbps(35), r2048Kbps(36), e1(37), t1(38), r896Kbps(39), r960Kbps(40), r1152Kbps(41), r1920Kbps(42), r34Mbps(43), r45Mbps(44), r1088Kbps(45), r1216Kbps(46), r1344Kbps(47), r1408Kbps(48), r1472Kbps(49), r1600Kbps(50), r1664Kbps(51), r1728Kbps(52), r1792Kbps(53), r1856Kbps(54), r1984Kbps(55), r1280Kbps(56), r2304Kbps(57), r832Kbps(58), r2176Kbps(59), r2432Kbps(60), r2560Kbps(61), r2688Kbps(62), r2816Kbps(63), r2944Kbps(64), r3072Kbps(65), r3200Kbps(66), r3328Kbps(67), r3456Kbps(68), r3584Kbps(69), r3712Kbps(70), r3840Kbps(71), r3968Kbps(72), r4096Kbps(73), r2112Kbps(74), r2240Kbps(75), r4224Kbps(76), r4352Kbps(77), r4480Kbps(78), r4608Kbps(79) | ||
| modmPrtDteCtsDelay | 1.3.6.1.4.1.164.3.4.4.4.1.1.6 | ||
| CTS/RTS delay, in msec. dxx = xx msec. notApplicable - for ASMi-31, ASMi-32. | |||
| OBJECT-TYPE | |||
| INTEGER | d0(1), d1(2), d7(3), d8(4), d10(5), d70(6), disabled(7), enabled(8), notApplicable(255) | ||
| modmPrtDteParity | 1.3.6.1.4.1.164.3.4.4.4.1.1.7 | ||
| This attribute indicates the parity mode in async frame. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), odd(2), even(3) | ||
| modmPrtDteIfType | 1.3.6.1.4.1.164.3.4.4.4.1.1.8 | ||
| The interface type of the DTE port. | |||
| OBJECT-TYPE | |||
| INTEGER | v24(1), rs530(2), x21(3), g703(4), v36(5), v35(6), g703r64k(7), hdb3(8), ethernet(9), g703T1(10), ethBNC(11), noIR(15), ipUtp(16), ethQ(17), rs530WA(18), v35WA(19), g704E1(20), ethQN(21), other(255) | ||
| modmPrtDteRlbEnable | 1.3.6.1.4.1.164.3.4.4.4.1.1.9 | ||
| Enable/Disable Remote Loop-Back on this modem, externally initiated. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| modmPrtDteAlbEnable | 1.3.6.1.4.1.164.3.4.4.4.1.1.10 | ||
| Enable/Disable Analog Loop-Back on this modem, externally initiated. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| modmPrtDteRtsDcdEnable | 1.3.6.1.4.1.164.3.4.4.4.1.1.11 | ||
| Enable/Disable RTS-DCD. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| modmPrtDteDsrDtrEnable | 1.3.6.1.4.1.164.3.4.4.4.1.1.12 | ||
| Enable/Disable DSR-DTR. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| modmPrtDteSignaling | 1.3.6.1.4.1.164.3.4.4.4.1.1.13 | ||
| Each bit represents a specific signal state. 1 - means : signal is ON , Enabled, Yes (exists) 0 - means : signal is OFF, Disabled, No . For detailed bit assignment see product's spec. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| modmPrtDteLoops | 1.3.6.1.4.1.164.3.4.4.4.1.1.14 | ||
| Loops that can be run on the DTE port. none - no loop (stop running loop) ana - Local Analog Line loop rem - Remote Analog Line loop anaAndBert - ana & BERT together remAndBert - rem & BERT together bert - BERT test twoBerts - 2 BERT test digital - A remote loop on the local modem. dual - Remote loop and ana loop. clb - Local loop on the DTE connection. Must be set together with modmPrtDteTestTimeOut parameter. Applicable to asmi51/CQ/CD. clbAndBert - CLB & BERT together. Applicable to asmi51/CQ/CD. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), ana(2), rem(3), anaAndBert(4), remAndBert(5), bert(6), twoBerts(7), digital(8), dual(9), clb(10), clbAndBert(11) | ||
| modmPrtDteTests | 1.3.6.1.4.1.164.3.4.4.4.1.1.15 | ||
| This is a mask which indicates - for Get: which tests are running on the DTE port. - for Set: tests the user wishes to start or stop. Each test has its specific bit. - '1' means the test runs (Set: should run). - '0' means the test does not run (Set: should stop): TEST BIT ----------- --- LEDs 0 e.g : If the return value is 1 the LEDs test is running. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtDteClearAllTests | 1.3.6.1.4.1.164.3.4.4.4.1.1.16 | ||
| Setting this attribute to on, clears all the running loops and tests of the DTE port. Upon completion, the value will automatically change to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmPrtDteBertResult | 1.3.6.1.4.1.164.3.4.4.4.1.1.17 | ||
| Result of BERT for the selected DTE port. Applicable only if BERT is running on the DTE port. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| modmPrtDteErrCorrect | 1.3.6.1.4.1.164.3.4.4.4.1.1.18 | ||
| notApplicable - for modems that do not support this object on - will start a random error correction process. onBurst - will start a burst error correction process. Setting this object to 'off', will stop any kind of error correction process. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3), onBurst(4) | ||
| modmPrtDteV54DigitalTest | 1.3.6.1.4.1.164.3.4.4.4.1.1.19 | ||
| Enables to start a remote digital loopback upon recognition of a special pattern. disable - will not start a digital loopback when a special pattern is recognized. enable - will start a loopback upon recognition of a special pattern. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| modmPrtDteV54DigitalTestStatus | 1.3.6.1.4.1.164.3.4.4.4.1.1.20 | ||
| Indicates whether a remote digital test was triggered by a pattern by the remote modem or not. no - the digital test wasn't triggered by a pattern by the remote modem. yes - the digital test was triggered by a pattern by the remote modem. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| modmPrtDteTestTimeOut | 1.3.6.1.4.1.164.3.4.4.4.1.1.21 | ||
| Indicates the timeout for LLB test. 0=Forever | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmLinePort | 1.3.6.1.4.1.164.3.4.4.5 | ||
| OBJECT IDENTIFIER | |||
| modmPrtLineTable | 1.3.6.1.4.1.164.3.4.4.5.1 | ||
| Configuration parameters of the Master and Slave Modem Line Ports. The port and unit (Master/Slave) is identified by its specific modmPrtLineIndex value. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModmPrtLineEntry | |||
| modmPrtLineEntry | 1.3.6.1.4.1.164.3.4.4.5.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModmPrtLineEntry | |||
| modmPrtLineIndex | 1.3.6.1.4.1.164.3.4.4.5.1.1.1 | ||
| The Line port index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modmPrtLineClkSrc | 1.3.6.1.4.1.164.3.4.4.5.1.1.2 | ||
| The clock source of the Line port. (5),(6) - applicable only for ASMi-24 and ASMi-50. (7),(8) - System level Clock Source. Applicable to CQ modems. | |||
| OBJECT-TYPE | |||
| INTEGER | localExtRemoteRcv(1), localIntRemoteRcv(2), localRcvRemoteInt(3), localRcvRemoteExt(4), localExtAutoRemoteRcv(5), localRcvRemoteExtAuto(6), localSysRemoteRcv(7), localRcvRemoteSys(8), internal(9), external(10), system(11), receive(12), notApplicable(255) | ||
| modmPrtLineTxLevel | 1.3.6.1.4.1.164.3.4.4.5.1.1.3 | ||
| Transmit level in dBm. pxx = positive xx = +xx nxx = negative xx = -xx | |||
| OBJECT-TYPE | |||
| INTEGER | n12(1), n9(2), n6(3), n3(4), p0(5), p4(6), p6(7), p10(8) | ||
| modmPrtLineRxLevel | 1.3.6.1.4.1.164.3.4.4.5.1.1.4 | ||
| Rx Sensitivity in dBm. pxx = positive xx = +xx nxx = negative xx = -xx. | |||
| OBJECT-TYPE | |||
| INTEGER | n14(1), n12(2), n10(3), n9(4), n6(5), n3(6), p0(7), low(8), high(9) | ||
| modmPrtLineOutImp | 1.3.6.1.4.1.164.3.4.4.5.1.1.5 | ||
| Output impedance in Ohm. | |||
| OBJECT-TYPE | |||
| INTEGER | infinite(1), i75ohm(2), i100ohm(3), i120ohm(4), i150ohm(5), i300ohm(6), i600ohm(7) | ||
| modmPrtLineInImp | 1.3.6.1.4.1.164.3.4.4.5.1.1.6 | ||
| Input impedance in Ohm. | |||
| OBJECT-TYPE | |||
| INTEGER | infinite(1), i75ohm(2), i100ohm(3), i120ohm(4), i150ohm(5), i300ohm(6), i600ohm(7) | ||
| modmPrtLineCarrCntrl | 1.3.6.1.4.1.164.3.4.4.5.1.1.7 | ||
| Carrier control. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| modmPrtLineRAP | 1.3.6.1.4.1.164.3.4.4.5.1.1.8 | ||
| Rate Adapting Protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | private(1), v110(2), v220(3), notApplicable(255) | ||
| modmPrtLineWaveLength | 1.3.6.1.4.1.164.3.4.4.5.1.1.9 | ||
| Wave Length of the optical Line. notApplicable - when the modem Line is not optical. The units are nano-meters [nm]. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), nm850(2), nm1300(3), nm780Laser(4), nm1300Laser(5), nm1550Laser(6) | ||
| modmPrtLineCdSense | 1.3.6.1.4.1.164.3.4.4.5.1.1.10 | ||
| Carrier Detect Sense - Detection Sensitivity of Carrier Wave. high - high sensitivity low - low sensitivity. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), high(2), low(3) | ||
| modmPrtLineAIS | 1.3.6.1.4.1.164.3.4.4.5.1.1.11 | ||
| AIS enable/disable. notApplicable - for modems that do not support this feature. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| modmPrtLineCoding | 1.3.6.1.4.1.164.3.4.4.5.1.1.12 | ||
| Line Coding. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), ami(2), hdb3(3), b8zs(4) | ||
| modmPrtLineLength | 1.3.6.1.4.1.164.3.4.4.5.1.1.13 | ||
| This attribute is the line length mask parameter used only for T1/DSU interfaces. len400p533ft=length range: 400ft to 533ft. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), len0p133ft(2), len134p266ft(3), len267p399ft(4), len400p533ft(5), len534p655ft(6), notApplicable(255) | ||
| modmPrtLineClkSrcPort | 1.3.6.1.4.1.164.3.4.4.5.1.1.14 | ||
| Clock Source Port. This parameter is relevant for external clock source. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), modem1(2), modem2(3), modem3(4), modem4(5) | ||
| modmPrtLineDteClkConfig | 1.3.6.1.4.1.164.3.4.4.5.1.1.15 | ||
| Indicates the clock source of the modems, which were not selected to supply the external clock. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dceExternal(2), dce(3) | ||
| modmPrtLineMaskAlr | 1.3.6.1.4.1.164.3.4.4.5.1.1.16 | ||
| This parameter determine whether masking or not the alarms for this line. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dontMask(2), mask(3) | ||
| kmux | 1.3.6.1.4.1.164.3.6 | ||
| OBJECT IDENTIFIER | |||
| systemKmux | 1.3.6.1.4.1.164.3.6.1 | ||
| OBJECT IDENTIFIER | |||
| generalKmux | 1.3.6.1.4.1.164.3.6.1.1 | ||
| OBJECT IDENTIFIER | |||
| sysGenKmuxTable | 1.3.6.1.4.1.164.3.6.1.1.1 | ||
| A table containing the general Kmux parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysGenKmuxEntry | |||
| sysGenKmuxEntry | 1.3.6.1.4.1.164.3.6.1.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysGenKmuxEntry | |||
| sysGenConfigIdx | 1.3.6.1.4.1.164.3.6.1.1.1.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). The write operation in this Table is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysGenFlipIntegration | 1.3.6.1.4.1.164.3.6.1.1.1.1.2 | ||
| The parameter is relevant only for KM-2100 and only when sysGenMlMode=redundancy, switchBackup, or priorityBumping. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), short(2), long(3) | ||
| sysGenMlMode | 1.3.6.1.4.1.164.3.6.1.1.1.1.3 | ||
| The Main Link operation mode. Determines how many links are used (one/two) and how they are used. | |||
| OBJECT-TYPE | |||
| INTEGER | single(2), redundancy(3), dualLink(4), priorityBumping(5), switchBackup(6) | ||
| sysGenFaType | 1.3.6.1.4.1.164.3.6.1.1.1.1.4 | ||
| Frame Allocation type: auto - automatic frame allocation (by Kmux) manual - manually configured frame allocation (by user). | |||
| OBJECT-TYPE | |||
| INTEGER | auto(2), manual(3) | ||
| sysGenLinkRecovery | 1.3.6.1.4.1.164.3.6.1.1.1.1.5 | ||
| The parameter determines the Link Recovery mode. The parameter is relevant only when the sysGenMlMode is either switchBackup or priorityBumping. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), auto(2), manual(3) | ||
| sysGenLinkSourceClock | 1.3.6.1.4.1.164.3.6.1.1.1.1.6 | ||
| The source clock for the links. The parameter is relevant only for KM-2100 having a KDI or KDI/CH cards. ML-A or ML-B are selectable only when sysGenMlMode=dual or priorityBumping. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), kmxMlA(103), kmxMlB(104) | ||
| sysGenMngBwA | 1.3.6.1.4.1.164.3.6.1.1.1.1.7 | ||
| The required management rate for ML-A, in bps. It is very important when a remote unit is managed. The selected value must be < ML-A Rate value. 0 = None or not applicable 800 bps = minimum value 19200 bps = maximum value | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysGenMngBwB | 1.3.6.1.4.1.164.3.6.1.1.1.1.8 | ||
| The required management rate for ML-B, in bps. It is very important when a remote unit is managed. The selected value must be < ML-B Rate value. 0 = None or not applicable 800 bps = minimum value 19200 bps = maximum value | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysGenAutoDialSlot | 1.3.6.1.4.1.164.3.6.1.1.1.1.9 | ||
| This object indicates the IO-SLOTs that can be used to initiate Automatic DialUp. This field will be applicable when KML.10 is a ML and its prtIsdnSwitchMode=auto. Each IO Slot is represented by a bit: 11 .............0 MSB(IO12) LSB(IO1) bit 0 (LSB) kmxIO1: '1'- used '0'- not used bit 1 kmxIO2: '1'- used '0'- not used bit 2 kmxIO3: '1'- used . '0'- not used . bit 11(MSB) kmxIO12: '1'- used '0'- not used The value will be: SUM of [2**n] ; n=bit number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysGenResetBypassEnable | 1.3.6.1.4.1.164.3.6.1.1.1.1.10 | ||
| Enable/Disable Reset Bypass operation when a KDI card exists and one of its links failed. notApplicable - when no KDI card exists in the Hub. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| sysGenLinkRecoveryCmd | 1.3.6.1.4.1.164.3.6.1.1.2 | ||
| Command to recover from ML failure. When 'on', the agent will perform manual link recovery and reset the variable to 'off'. The conditions for this action are: sysGenMlMode= priorityBumping or switchBackup and also sysGenLinkRecovery=manual(3). | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), off(2), on(3) | ||
| sysGenFlipMlCmd | 1.3.6.1.4.1.164.3.6.1.1.3 | ||
| Command to flip the ML when sysGenMlMode=redundancy. When 'on', the agent will flip the ML and reset the variable to 'off'. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), off(2), on(3) | ||
| sysGenMonitorChannel | 1.3.6.1.4.1.164.3.6.1.1.4 | ||
| The variable specifies the channel to be monitored and presented on the front panel LEDs. The channel will be specified according to: Slot*100+Ch. 0 - no monitoring. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| statusKmux | 1.3.6.1.4.1.164.3.6.1.2 | ||
| OBJECT IDENTIFIER | |||
| sysStatusOnLineML | 1.3.6.1.4.1.164.3.6.1.2.1 | ||
| The main links which are online. | |||
| OBJECT-TYPE | |||
| INTEGER | both(1), kmxMlA(103), kmxMlB(104) | ||
| sysKmuxStatus | 1.3.6.1.4.1.164.3.6.1.2.2 | ||
| A BIT string indicating the system status as follows On - the bit is set to '1': Bit 0 (LSB): Alarm Relay. Bit 1: SP param. Off- Configure the SP port from the database On - Default parameters (9600bps, 8 data bits, no parity, one stop bit). Bit 2: DBinit. The status of the dip switch in the Common Logic Card. Off- Configuration parameters were determined by the user. On - Default configuration parameters are loaded on mux power-on. Bit 3: DownloadBw. Off - Disable in-band management. On - Enable in-band management. Bit 4 (MSB): Passwd. Off - No password is required. On - Password is required. Example: 8 (10000) means Passwd.=On and all the others off. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysKmuxOffset | 1.3.6.1.4.1.164.3.6.1.2.3 | ||
| 'on' - slots 1..4 of KM-2104 match slots 11..14 of KM-2100. 'off'- slots 1..4 of KM-2104 match slots 7..10 of KM-2100. notApplicable - for KM-2100. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| backupKmux | 1.3.6.1.4.1.164.3.6.1.3 | ||
| OBJECT IDENTIFIER | |||
| sysBackupTable | 1.3.6.1.4.1.164.3.6.1.3.1 | ||
| A table containing the backup parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysBackupEntry | |||
| sysBackupEntry | 1.3.6.1.4.1.164.3.6.1.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysBackupEntry | |||
| sysBackupConfigIdx | 1.3.6.1.4.1.164.3.6.1.3.1.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysBackupDatabase | 1.3.6.1.4.1.164.3.6.1.3.1.1.2 | ||
| Determines the database to switch to, when ML recovery occurs. | |||
| OBJECT-TYPE | |||
| INTEGER | onLine(2), alternate(3) | ||
| sysBackupMode | 1.3.6.1.4.1.164.3.6.1.3.1.1.3 | ||
| isdn - for connection to ISDN network. pstn - for connection to PSTN network. | |||
| OBJECT-TYPE | |||
| INTEGER | isdn(2), pstn(3) | ||
| sysBackupDialTimeout | 1.3.6.1.4.1.164.3.6.1.3.1.1.4 | ||
| The dial timeout in seconds (when backup is attempted). | |||
| OBJECT-TYPE | |||
| INTEGER | sec30(2), sec45(3), sec60(4), sec120(5) | ||
| sysBackupOptions | 1.3.6.1.4.1.164.3.6.1.3.1.1.5 | ||
| The Backup options: noBackup - No backup is applicable line - Line Data backup path - Line Mng backup . | |||
| OBJECT-TYPE | |||
| INTEGER | noBackup(2), line(3), path(4) | ||
| sysBackupAgendaTable | 1.3.6.1.4.1.164.3.6.1.3.2 | ||
| A table containing the backup schedule. It is possible to define 4 different time zone schedules per day of the week. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysBackupAgendaEntry | |||
| sysBackupAgendaEntry | 1.3.6.1.4.1.164.3.6.1.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysBackupAgendaEntry | |||
| sysBackupCfgIdx | 1.3.6.1.4.1.164.3.6.1.3.2.1.1 | ||
| This object indicates the Configuration number (1,255) referred. Write operation for the table entries is allowed only to the temporary configuration (255). | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), temporary(255) | ||
| sysBackupDay | 1.3.6.1.4.1.164.3.6.1.3.2.1.2 | ||
| Day of the week. | |||
| OBJECT-TYPE | |||
| INTEGER | sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7) | ||
| sysBackupZone | 1.3.6.1.4.1.164.3.6.1.3.2.1.3 | ||
| The time zone. | |||
| OBJECT-TYPE | |||
| INTEGER | zone1(1), zone2(2), zone3(3), zone4(4), zone5(5) | ||
| sysBackupEndTime | 1.3.6.1.4.1.164.3.6.1.3.2.1.4 | ||
| The end time for this time zone. The format is HH:MM. For example 23:59. For Zone 4, End Time = 23:59 (constant). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| sysBackupStatus | 1.3.6.1.4.1.164.3.6.1.3.2.1.5 | ||
| Enable or disable this backup schedule entry. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| frameAllocationKmux | 1.3.6.1.4.1.164.3.6.1.4 | ||
| OBJECT IDENTIFIER | |||
| sysFrameAllocationTable | 1.3.6.1.4.1.164.3.6.1.4.1 | ||
| A table for manually configuring the frame allocation. The table will contain always all the programmed cards' ports. sysFaNumOfBits | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysFrameAllocationEntry | |||
| sysFrameAllocationEntry | 1.3.6.1.4.1.164.3.6.1.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SysFrameAllocationEntry | |||
| sysFaConfigIdx | 1.3.6.1.4.1.164.3.6.1.4.1.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| sysFaLink | 1.3.6.1.4.1.164.3.6.1.4.1.1.2 | ||
| The main link on which frame allocation is done. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxMlA(103), kmxMlB(104) | ||
| sysFaPrt | 1.3.6.1.4.1.164.3.6.1.4.1.1.3 | ||
| The Frame Allocation (FA) port. The ports will be specified by: Slot*100+Ch. - for Bypass of KDI or KDI/CH the port will be: Slot*100+11 (internal-1=non-existent port ; just for use of the same MIB table) - for all the programmed cards, there will be an artificial port entry that will represent the card, in order to specify the Control Signal Bits that are at card level: Slot*100+0 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysFaStartingBit | 1.3.6.1.4.1.164.3.6.1.4.1.1.4 | ||
| The data starting bit for the channel. - for Bypass of KDI or KDI/CH, this will be the Starting Bit of the Bypass Window on the specific sysFaLink. - for Control Signals of a card ( sysFaPrt=Slot*100+0) this will be the Starting Bit of the Control Signals of the card. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..239 | ||
| sysFaNumOfBits | 1.3.6.1.4.1.164.3.6.1.4.1.1.5 | ||
| The data size in number of bits for the channel. - for Bypass of KDI or KDI/CH, this will be the Bypass Window size. In this case, this value must be the same for both MLs. - for Control Signals of a card ( sysFaPrt=Slot*100+0) this will be the number of Control Signal Bits of the card. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..239 | ||
| sysDisconnectSupervisionEventTable | 1.3.6.1.4.1.164.3.6.1.5 | ||
| Disconnect Supervision Event table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysDisconnectSupervisionEventEntry | |||
| sysDisconnectSupervisionEventEntry | 1.3.6.1.4.1.164.3.6.1.5.1 | ||
| An entry in the table. | |||
| OBJECT-TYPE | |||
| SysDisconnectSupervisionEventEntry | |||
| sysDsEventIdx | 1.3.6.1.4.1.164.3.6.1.5.1.1 | ||
| This object indicates a unique Event Index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sysDsEventSlot | 1.3.6.1.4.1.164.3.6.1.5.1.2 | ||
| This object indicates a unique number of the slot position, where the KVF.6 or KVF.8 card is inserted, and the Disconnect Supervision Event occurred. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| sysDsEventTS | 1.3.6.1.4.1.164.3.6.1.5.1.3 | ||
| This object defines the Time Slot number, where the Disconnect Supervision Event occurred. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..31 | ||
| sysDsEventDescr | 1.3.6.1.4.1.164.3.6.1.5.1.4 | ||
| This object defines the Description of the Disconnect Supervision Event. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| sysDsEventDateAndTime | 1.3.6.1.4.1.164.3.6.1.5.1.5 | ||
| This object defines the Date and Time, when the Disconnect Supervision Event occurred. It will be displayed in the following format: YYYY-MM-DD HH:MM:SS. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| mdlKmux | 1.3.6.1.4.1.164.3.6.2 | ||
| OBJECT IDENTIFIER | |||
| mdlKmxTable | 1.3.6.1.4.1.164.3.6.2.2 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlKmxEntry | |||
| mdlKmxEntry | 1.3.6.1.4.1.164.3.6.2.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlKmxEntry | |||
| mdlKmxConfigIdx | 1.3.6.1.4.1.164.3.6.2.2.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| mdlKmxSlotIdx | 1.3.6.1.4.1.164.3.6.2.2.1.2 | ||
| This object indicates a unique number of the slot position in which the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxPsA(101), kmxPsB(102), kmxMlA(103), kmxMlB(104), kmxCl(105), kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlKmxOperatedMl | 1.3.6.1.4.1.164.3.6.2.2.1.3 | ||
| The main link for this card. The field is relevant only for ML modes of Dual, Priority Bumping and Switched Backup. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), kmxMlA(103), kmxMlB(104), kmxMlAandMlB(119) | ||
| mdlKmxMlAtoMlBPrio | 1.3.6.1.4.1.164.3.6.2.2.1.4 | ||
| ML-A to ML-B Priority. The field is relevant only for ML modes of Priority Bumping and Switched Backup. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), low(2), high(3) | ||
| mdlKmxMlBtoMlAPrio | 1.3.6.1.4.1.164.3.6.2.2.1.5 | ||
| ML-B to ML-A Priority. The field is relevant only for ML modes of Priority Bumping. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), low(2), high(3) | ||
| mdlKmxOutSrvMethod | 1.3.6.1.4.1.164.3.6.2.2.1.6 | ||
| Out of service method. For KVC.1 and KVC.1M all values are applicable. For KVC.2, KVC.3, KVF.1, KVF.3, KVF.4: only forcedIdle and forcedBusy are applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), idleBusy(2), forcedIdle(3), busyIdle(4), forcedBusy(5) | ||
| mdlKmxV54Config | 1.3.6.1.4.1.164.3.6.2.2.1.7 | ||
| Relevant only for KLS.1/New card. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dceDce(2), dceDte(3), dteDce(4), dteDte(5) | ||
| mdlKmxTiming | 1.3.6.1.4.1.164.3.6.2.2.1.8 | ||
| Applicable only for KHSU.1, KHSU.2, KVF.4/S0, KVC.3/S0 cards. lt - local timing nt - network timing te - terminal equipment | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), lt(2), nt(3), te(4) | ||
| mdlKvf5PbxTable | 1.3.6.1.4.1.164.3.6.2.3 | ||
| Parameters specific to KVF.5, KVF.6 and KVF.8 PBX cards. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlKvf5PbxEntry | |||
| mdlKvf5PbxEntry | 1.3.6.1.4.1.164.3.6.2.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MdlKvf5PbxEntry | |||
| mdlKvf5PbxConfigIdx | 1.3.6.1.4.1.164.3.6.2.3.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| mdlKvf5PbxSlotIdx | 1.3.6.1.4.1.164.3.6.2.3.1.2 | ||
| This object indicates a unique number of the slot position in which the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlKvf5PbxSig | 1.3.6.1.4.1.164.3.6.2.3.1.3 | ||
| Signaling type. When 'mdlKvf5PbxSig' is valid, 'mdlKvf5PbxSigTxPbx' and 'mdlKvf5PbxSigRxPbx' are not valid. mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver and KVF.6 card. mdlKvf5PbxSigTxPbx and mdlKvf5PbxSigRxPbx - are supported by KVF.5 NEW SW ver and KVF.6. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), a(2), aANDb(3), b(4), ccs(5), cas(6) | ||
| mdlKvf5PbxSigMode | 1.3.6.1.4.1.164.3.6.2.3.1.4 | ||
| Signaling Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), direct(2), inverse(3) | ||
| mdlKvf5PbxTsAssign | 1.3.6.1.4.1.164.3.6.2.3.1.5 | ||
| Ts Assignment group. Each KVF.5 card of the Mux should have a different value. For KVF.5/E1 values: 2,3,4,8,9,10,11,12 are applicable. For KVF.5/T1 values: 2,3,4,5,6,7 are applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | s1s2s3s4(2), s5s6s7s8(3), s9s10s11s12(4), s13s14s15s16(5), s17s18s19s20(6), s21s22s23s24(7), s13s14s15s17(8), s18s19s20s21(9), s22s23s24s25(10), s26s27s28s29(11), s30s31(12) | ||
| mdlKvf5PbxCcsTs | 1.3.6.1.4.1.164.3.6.2.3.1.6 | ||
| CCS TS of the KVF.5/T1/E1 and KVF.6/T1/E1 card. It is applicable for Kmux KVF.5 Framer cards and KVF.6 cards when mdlKvf5PbxSig=ccs. Valid values: 1..24 - CCS TS of T1 1..31 - CCS TS of E1 255 - notApplicable (for agents that do not support this feature or for irrelevant cards) Other values are invalid. The value selected should not be the same as one of the TSs assigned for any card of the same group via mdlKvf5PbxTsAssign. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlKvf5PbxOos | 1.3.6.1.4.1.164.3.6.2.3.1.7 | ||
| 'idle' = '0' = on-hook, idle state 'busy' = '1' = off-hook, busy state 'forcedIdle' = SP = both A and B signaling bits are forced to '0' during out-of-service periods. 'forcedBusy' = MK = both A and B signaling bits are forced to '1' during out-of-service periods. - for T1: '0'=0 ; '1'=1 - for E1: '0'=1 ; '1'=0 | |||
| OBJECT-TYPE | |||
| INTEGER | notSupported(2), forcedIdle(3), forcedBusy(4) | ||
| mdlKvf5PbxSigTxPbx | 1.3.6.1.4.1.164.3.6.2.3.1.8 | ||
| TxPbx signaling means transmit signaling from KM to PBX (KM-->PBX) When 'mdlKvf5PbxSigTxPbx' is valid, 'mdlKvf5PbxSig' field is not valid. mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver. mdlKvf5PbxSigTxPbx and mdlKvf5PbxSigRxPbx - are supported by KVF.5 NEW SW ver. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), a(2), b(3), aANDb(4), crossAandB(5), ccs(6), aEqualsB(7) | ||
| mdlKvf5PbxSigRxPbx | 1.3.6.1.4.1.164.3.6.2.3.1.9 | ||
| RxPbx signaling means receive signaling from PBX to KM (PBX-->KM-->KM) When 'mdlKvf5PbxSigRxPbx' is valid, 'mdlKvf5PbxSig' field is not valid. mdlKvf5PbxSig - is supported by KVF.5 OLD SW ver. mdlKvf5PbxSigTxPbx and mdlKvf5PbxSigRxPbx - are supported by KVF.5 NEW SW ver. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), a(2), b(3), aANDb(4), ccs(6) | ||
| mdlKvf5PbxDefABCD | 1.3.6.1.4.1.164.3.6.2.3.1.10 | ||
| This object determines what KM will send for the ABCD Bits that are not 'filled' by the dynamic signaling. This field is applicable only for signaling transmit to PBX ('mdlKvf5PbxSigTxPbx'). For KVF.5 cards: valid range (00 - 0F HEX) - ABCD Bits. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..1) | ||
| mdlKvf5PbxFramerSlot | 1.3.6.1.4.1.164.3.6.2.3.1.11 | ||
| This object indicates the Framer's slot number this card belongs to. Several cards having the same mdlKvf5PbxFramerSlot value, work together as a group. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118), notApplicable(255) | ||
| mdlKvf5PbxCcsRate | 1.3.6.1.4.1.164.3.6.2.3.1.12 | ||
| Determines the Ccs speed - for KVF.6 and KVF.5 cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), bps4800(2), bps6400(3), bps9600(4), bps12800(5), bps16000(6), bps19200(7), bps32000(8), bps64000(9) | ||
| mdlKvf5PbxTxAbcdBit | 1.3.6.1.4.1.164.3.6.2.3.1.13 | ||
| This object is applicable only for KVF.6 and KVF.8 cards, when mdlKvf5PbxSig=cas(6). It represents 4 parameters, by 2 Octets : D Bit Code-MSB nibble, C Bit Code- nibble, B Bit Code- nibble, A Bit Code-LSB nibble. Each of A,B,C,D Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-E hex - not used (invalid values) When the object is not applicable, 0 Octets will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlKvf5PbxHdlcCrc | 1.3.6.1.4.1.164.3.6.2.3.1.14 | ||
| Determines the CRC type of HDLC protocol, that CCS signaling is working with. Applicable for KVF.6 cards when Signaling is CCS (only). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), crc16(2), crc32(3) | ||
| mdlDisconnectSupervisionTable | 1.3.6.1.4.1.164.3.6.2.4 | ||
| Disconnect Supervision table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MdlDisconnectSupervisionEntry | |||
| mdlDisconnectSupervisionEntry | 1.3.6.1.4.1.164.3.6.2.4.1 | ||
| An entry in the table. | |||
| OBJECT-TYPE | |||
| MdlDisconnectSupervisionEntry | |||
| mdlDsConfigIdx | 1.3.6.1.4.1.164.3.6.2.4.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| mdlDsSlotIdx | 1.3.6.1.4.1.164.3.6.2.4.1.2 | ||
| This object indicates a unique number of the slot position in which the module is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| mdlDs | 1.3.6.1.4.1.164.3.6.2.4.1.3 | ||
| This object defines which terms will cause disconnection of call. disable = the Disconnect Supervision feature is disabled. In this case, all other objects of this table are irrelevant. Remote Sanity - If mdlDsUserLoc = Remote Location , the valid values are : disable(1), silenceOnly(4), fastBusyOnly(5), silenceOrFastBusy(6). If mdlDsUserLoc = Local , the valid values are disable(1), remoteDisconnect(2), remoteDisconnectAndSilence (3). | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), remoteDisconnect(2), remoteDisconnectAndSilence(3), silenceOnly(4), fastBusyOnly(5), silenceOrFastBusy(6) | ||
| mdlDsUserLoc | 1.3.6.1.4.1.164.3.6.2.4.1.4 | ||
| User located in local or remote station. Local station will disconnect the call actually if needed. Applicable only if Disconnect Supervision (mdlDs) is different from disable. Should be a Sanity check between the mdlDs and the mdlDsUserLoc parameters (see mdlDs). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), remote(2), local(3) | ||
| mdlDsMode | 1.3.6.1.4.1.164.3.6.2.4.1.5 | ||
| This object defines the action, which will be done after remote disconnect occurred. This object is relevant only when mdlDsUserLoc = local(3). Applicable only if Disconnect Supervision (mdlDs) is different from disable AND User Location (mdlDsUserLoc) = local(3). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), reportOnly(2), disconnect(3) | ||
| mdlDsSilence | 1.3.6.1.4.1.164.3.6.2.4.1.6 | ||
| This object defines the silence period needed for an indication (seconds). Applicable only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Silence', i.e. is one of the following: remoteDisconnectAndSilence(3), silenceOnly(4), silenceOrFastBusy(6). Valid values: 0,20,40..(every 20 seconds)..300, 0 = notApplicable. notApplicable = silence disabled when mdlDs doesn't include 'silence'. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsClrFwSig | 1.3.6.1.4.1.164.3.6.2.4.1.7 | ||
| This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards. This object is an indication of Near PBX to the Far PBX, that it wants to disconnect the call. Applicable only if Disconnect Supervision (mdlDs) is different from disable. Applicable only for KVF.6 cards. It represents 4 parameters, by an Octet: ( Bit 7 = MSB, Bit 0 = LSB ) D Bit - bits 6,7 of the MSB nibble, C Bit - bits 4,5 of the MSB nibble, B Bit - bits 2,3 of the LSB nibble, A Bit - bits 0,1 of the LSB nibble. For each of A,B,C,D Bits: 00 = 0, 01 = 1, 10 = reserved, 11 = x. For A,B Bits - only one of them can be 'x' (not both at the same time). For C,D Bits - 'x' won't be in use. When the object is not applicable, a 0 Octet will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlDsAnswerSig | 1.3.6.1.4.1.164.3.6.2.4.1.8 | ||
| This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards. This object is an indication of Near PBX to the Far PBX, taht a call is present now on the line. Applicable only if Disconnect Supervision (mdlDs) is different from disable. Applicable only for KVF.6 cards. It represents 4 parameters, by an Octet: ( Bit 7 = MSB, Bit 0 = LSB ) D Bit - bits 6,7 of the MSB nibble, C Bit - bits 4,5 of the MSB nibble, B Bit - bits 2,3 of the LSB nibble, A Bit - bits 0,1 of the LSB nibble. For each of A,B,C,D Bits: 00 = 0, 01 = 1, 10 = reserved, 11 = x. For A,B Bits - only one of them can be 'x' (not both at the same time). For C,D Bits - 'x' won't be in use. When the object is not applicable, a 0 Octet will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlDsClrBwSig | 1.3.6.1.4.1.164.3.6.2.4.1.9 | ||
| This object defines the Clear FWD Signal (A,B,C,D bits) for KVF.6 cards. This object is an indication of Far PBX to the Near PBX, that the call was disconnected (on the Far side). Applicable only if Disconnect Supervision (mdlDs) is different from disable. Applicable only for KVF.6 cards. It represents 4 parameters, by an Octet: ( Bit 7 = MSB, Bit 0 = LSB ) D Bit - bits 6,7 of the MSB nibble, C Bit - bits 4,5 of the MSB nibble, B Bit - bits 2,3 of the LSB nibble, A Bit - bits 0,1 of the LSB nibble. For each of A,B,C,D Bits: 00 = 0, 01 = 1, 10 = reserved, 11 = x. For A,B,C,D Bits - 'x' won't be in use. When the object is not applicable, a 0 Octet will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mdlDsFbtLowFreq | 1.3.6.1.4.1.164.3.6.2.4.1.10 | ||
| First frequency in Fast Busy Tone (Fbt) combination (Hz). Valid values: 0..4000,4095. 4095 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtHighFreq | 1.3.6.1.4.1.164.3.6.2.4.1.11 | ||
| Second frequency in Fast Busy Tone (Fbt) combination (Hz). Valid values: 0..4000,4095. 4095 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtTimeOn1 | 1.3.6.1.4.1.164.3.6.2.4.1.12 | ||
| This object defines the Time On 1 cadence (in msec). Valid values: 0,10,20..(every 10 msec)..10000,10230. 0 = disable, 10230 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtTimeOff1 | 1.3.6.1.4.1.164.3.6.2.4.1.13 | ||
| This object defines the Time Off 1 cadence (in msec). Valid values: 0,10,20..(every 10 msec)..10000,10230. 0 = disable, 10230 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtTimeOn2 | 1.3.6.1.4.1.164.3.6.2.4.1.14 | ||
| This object defines the Time On 2 cadence (in msec). Valid values: 0,10,20..(every 10 msec)..10000,10230. 0 = disable, 10230 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtTimeOff2 | 1.3.6.1.4.1.164.3.6.2.4.1.15 | ||
| This object defines the Time Off 2 cadence (in msec). Valid values: 0,10,20..(every 10 msec)..10000,10230. 0 = disable, 10230 = notApplicable. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtLowFreqLevel | 1.3.6.1.4.1.164.3.6.2.4.1.16 | ||
| First frequency level for Fast Busy Tone (Fbt) in dBm units. Valid values: -32..31. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mdlDsFbtHighFreqLevel | 1.3.6.1.4.1.164.3.6.2.4.1.17 | ||
| Second frequency level for Fast Busy Tone (Fbt) in dBm units. Valid values: -32..31. Available only if Disconnect Supervision (mdlDs) is different from disable AND includes 'Tones' (Fast Busy), i.e. is one of the following: fastBusyOnly(5), silenceOrFastBusy(6). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtKmux | 1.3.6.1.4.1.164.3.6.3 | ||
| OBJECT IDENTIFIER | |||
| prtMainLink | 1.3.6.1.4.1.164.3.6.3.1 | ||
| OBJECT IDENTIFIER | |||
| prtMlFrameStatsTable | 1.3.6.1.4.1.164.3.6.3.1.1 | ||
| Frame diagnostics for the main links. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMlFrameStatsEntry | |||
| prtMlFrameStatsEntry | 1.3.6.1.4.1.164.3.6.3.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtMlFrameStatsEntry | |||
| prtMlFrameIdx | 1.3.6.1.4.1.164.3.6.3.1.1.1.1 | ||
| The prtGenPrtIdx index of this link. Slot*100+1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlFrameSlt | 1.3.6.1.4.1.164.3.6.3.1.1.1.2 | ||
| This attribute indicates a unique number to identify the slot where the ML card is inserted. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxMlA(103), kmxMlB(104) | ||
| prtMlBitWeight | 1.3.6.1.4.1.164.3.6.3.1.1.1.3 | ||
| This attribute indicates the Bit Weight [bps/bit] used for the selected prtMlFrameSlt. The Bit Weight is according to the ML Speed. | |||
| OBJECT-TYPE | |||
| INTEGER | bps400(1), bps800(2), bps1600(3), bps3200(4), bps6400(5) | ||
| prtMlDataUsage | 1.3.6.1.4.1.164.3.6.3.1.1.1.4 | ||
| Data usage in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlControlSig | 1.3.6.1.4.1.164.3.6.3.1.1.1.5 | ||
| Control Signals usage of the ML in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlDownload | 1.3.6.1.4.1.164.3.6.3.1.1.1.6 | ||
| Download bandwidth usage of the ML in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlSync | 1.3.6.1.4.1.164.3.6.3.1.1.1.7 | ||
| Sync bandwidth usage of the ML in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlTotalUsage | 1.3.6.1.4.1.164.3.6.3.1.1.1.8 | ||
| Total bandwidth usage of the ML in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlTotalFree | 1.3.6.1.4.1.164.3.6.3.1.1.1.9 | ||
| Free bandwidth of the ML in [bits]. In order to convert it to 'bps' units, the 'bits' should be multiplied by prtMlBitWeight value. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlTable | 1.3.6.1.4.1.164.3.6.3.1.2 | ||
| Parameters for the main links. KML.1 - KML.6, KML.7(T1), KML.8(E1), KML.10(ISDN) and KML.F(KML.11 Fiber-optic). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMlEntry | |||
| prtMlEntry | 1.3.6.1.4.1.164.3.6.3.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtMlEntry | |||
| prtMlCnfgIdx | 1.3.6.1.4.1.164.3.6.3.1.2.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtMlIdx | 1.3.6.1.4.1.164.3.6.3.1.2.1.2 | ||
| The prtGenPrtIdx index of this link. Slot*100+1 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlSlt | 1.3.6.1.4.1.164.3.6.3.1.2.1.3 | ||
| This attribute indicates a unique number to identify the slot where the ML card is inserted in. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxMlA(103), kmxMlB(104) | ||
| prtMlTiming | 1.3.6.1.4.1.164.3.6.3.1.2.1.4 | ||
| The clock source for this link. For KML.1-KML.4, valid values: dte, eDce, or dce. For KML.5-KML.8, valid values: int or lbt. notApplicable - for KML.10 and KML.F. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dte(2), dce(3), eDce(4), int(5), lbt(6), adaptive(7) | ||
| prtMlBufferSize | 1.3.6.1.4.1.164.3.6.3.1.2.1.5 | ||
| The buffer size in bits for absorbing timing jitters. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), bits8(2), bits256(3) | ||
| prtMlDsrCts | 1.3.6.1.4.1.164.3.6.3.1.2.1.6 | ||
| Determines the DSR and CTS signal handling. notApplicable - for KML.4-KML.6. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), internal(2), external(3) | ||
| prtMlSpeed | 1.3.6.1.4.1.164.3.6.3.1.2.1.7 | ||
| Determines the Main Link port speed. KML.1, KML.3, KML.4 support (Kbps): 9.6, 14.4, 19.2, 28.8, 32, 48, 56, 64, 128, 192, 256, 384, 512, 768, 1024, 1536. KML.2 supports (Kbps): 9.6, 14.4, 19.2, 28.8, 32, 48, 56, 64, 128 KML.5 supports (Kbps): 64, 128. KML.6 supports (Kbps): 9.6, 19.2, 56. KML.7-KML.8 support (Kbps): 56, 64, 128, 192, 256, 384, 512, 768, 1024, 1536. KML.10 supports (Kbps): 64, 128. KML.F supports (Kbps): 128, 256, 384, 512, 768, 1024, 1536. | |||
| OBJECT-TYPE | |||
| INTEGER | bps9600(2), bps14400(3), bps19200(4), bps28800(5), bps32000(6), bps48000(7), bps56000(8), bps64000(9), bps128000(10), bps192000(11), bps256000(12), bps384000(13), bps512000(14), bps768000(15), bps1024000(16), bps1536000(17) | ||
| prtMlStartTS | 1.3.6.1.4.1.164.3.6.3.1.2.1.8 | ||
| 0=notApplicable - for all cards except KML.7, KML.8 For KML.7 - valid values: 1..24 For KML.8 - valid values: 1..31. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..31 | ||
| prtMlBypassTs16 | 1.3.6.1.4.1.164.3.6.3.1.2.1.9 | ||
| notApplicable - for all cards except KML.8. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtMlCallMode | 1.3.6.1.4.1.164.3.6.3.1.2.1.10 | ||
| This object will be used when using an external modem linked to the KML.1-KML.4 or KML.10 cards. Initiate - KML card can initiate calls to the modem Listen - KML card listens only ; cannot initiate a call. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), initiate(2), listen(3) | ||
| prtMlBondingEnable | 1.3.6.1.4.1.164.3.6.3.1.2.1.11 | ||
| Disable/Enable applying the Bonding process, for KML.10 cards. notApplicable - for all cards except KML.10. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disabled(2), enabled(3) | ||
| prtMlIsdnTable | 1.3.6.1.4.1.164.3.6.3.1.3 | ||
| Parameters for ISDN main links: KML.10. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtMlIsdnEntry | |||
| prtMlIsdnEntry | 1.3.6.1.4.1.164.3.6.3.1.3.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtMlIsdnEntry | |||
| prtMlIsdnCnfgIdx | 1.3.6.1.4.1.164.3.6.3.1.3.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtMlIsdnIdx | 1.3.6.1.4.1.164.3.6.3.1.3.1.2 | ||
| The prtGenPrtIdx index of this link. Slot*100+1 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtMlIsdnSlt | 1.3.6.1.4.1.164.3.6.3.1.3.1.3 | ||
| This attribute indicates a unique number to identify the slot where the ML card is inserted in. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxMlA(103), kmxMlB(104) | ||
| prtMlIsdnMode | 1.3.6.1.4.1.164.3.6.3.1.3.1.4 | ||
| ISDN Mode. switched - when ML Mode is Switched Backup. leased - in all other cases. | |||
| OBJECT-TYPE | |||
| INTEGER | leased(2), switched(3) | ||
| prtMlIsdnStandard | 1.3.6.1.4.1.164.3.6.3.1.3.1.5 | ||
| The ISDN standard. | |||
| OBJECT-TYPE | |||
| INTEGER | european(2), israeli(3), ess5Multipoint(4), ess5Ptp(5), dms100(6), ntt(7), nationalIsdn1(8) | ||
| prtMlIsdnLocSubNum | 1.3.6.1.4.1.164.3.6.3.1.3.1.6 | ||
| Local sub-number. 4 chars (digits 0..9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..25) | ||
| prtMlIsdnLocNum | 1.3.6.1.4.1.164.3.6.3.1.3.1.7 | ||
| Local number. 20 chars (digits: 0..9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..25) | ||
| prtMlIsdnOutSubNum | 1.3.6.1.4.1.164.3.6.3.1.3.1.8 | ||
| Out sub-number. 4 chars (digits 0..9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..25) | ||
| prtMlIsdnBackupCallNum | 1.3.6.1.4.1.164.3.6.3.1.3.1.9 | ||
| Backup call number. 20 chars (digits: 0..9). | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..25) | ||
| prtMlIsdnInNumMode | 1.3.6.1.4.1.164.3.6.3.1.3.1.10 | ||
| In number mode. | |||
| OBJECT-TYPE | |||
| INTEGER | none(2), all(3), local(4) | ||
| prtHsLs | 1.3.6.1.4.1.164.3.6.3.2 | ||
| OBJECT IDENTIFIER | |||
| prtHsLsTable | 1.3.6.1.4.1.164.3.6.3.2.1 | ||
| Parameters for the High and Low speed channels. Cards: KLS.1,KLS.2, KHS.1, KHS.2, KDI/CH, KHSU.1, KHSU.2, KHS.703. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtHsLsEntry | |||
| prtHsLsEntry | 1.3.6.1.4.1.164.3.6.3.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtHsLsEntry | |||
| prtHsLsCnfgIdx | 1.3.6.1.4.1.164.3.6.3.2.1.1.1 | ||
| This attribute indicates the Idx of the Config being accessed. Idx of 255 relates to the Temporary (Scratch) Config. Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtHsLsIdx | 1.3.6.1.4.1.164.3.6.3.2.1.1.2 | ||
| The prtGenPrtIdx index of this channel. In KHSU.1 and KHSU.2 there are three ISDN sub-channels on each port (2B+D).The sub-channels are numbered: Slot*100+11 ; Slot*100+12 ; Slot*100+13 (First Port), Slot*100+14 ; Slot*100+15 ; Slot*100+16 (Second Port). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtHsLsSlt | 1.3.6.1.4.1.164.3.6.3.2.1.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. The entry kmxOpt(106) is valid only for KDI/CH card. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxOpt(106), kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| prtHsLsCommProtocol | 1.3.6.1.4.1.164.3.6.3.2.1.1.4 | ||
| The communication protocol. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), async(2), sync(3) | ||
| prtHsLsAsyncDataLen | 1.3.6.1.4.1.164.3.6.3.2.1.1.5 | ||
| Async Data Length in Bits. notApplicable - when prtHsLsCommProtocol=sync or notApplicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), bit6(2), bit7(3), bit8(4), bit9(5) | ||
| prtHsLsTiming | 1.3.6.1.4.1.164.3.6.3.2.1.1.6 | ||
| The variable is RW only if the communications protocol is sync. When the comm protocol is async, the variable is RO and its value is DCE. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dce(2), dte1(3), dte2(4) | ||
| prtHsLsCtrlSignal | 1.3.6.1.4.1.164.3.6.3.2.1.1.7 | ||
| Control signals. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), local(2), dtrAndRts(3), rts(4) | ||
| prtHsLsCts | 1.3.6.1.4.1.164.3.6.3.2.1.1.8 | ||
| CTS Signal. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), equalRts(2), on(3) | ||
| prtHsLsRtsCtsDelay | 1.3.6.1.4.1.164.3.6.3.2.1.1.9 | ||
| RTS-CTS delay in ms. notApplicable - when prtHsLsCts=on. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), min(2), ms10(3), ms50(4), ms100(5), ms200(6) | ||
| prtHsLsDsrMode | 1.3.6.1.4.1.164.3.6.3.2.1.1.10 | ||
| DSR Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), permanentOn(2), sync(3) | ||
| prtHsLsSpeed | 1.3.6.1.4.1.164.3.6.3.2.1.1.11 | ||
| KLS.1 supports (Kbps): 0.3, 0.6, 1.2, 2.4, 4.8, 9.6, 19.2, 38.4. KLS.1/New, KDI/CH support (Kbps): Group 1: 0.3, 0.6, 1.2, 2.4, 4.8, 9.6, 19.2, 38.4 Group 2: 7.2, 14.4, 28.8, 57.6 Group 3: 8, 16, 24, 32, 48, 56, 64 KLS.2 supports (Kbps): 2.4, 4.8, 9.6, 19.2. KHS.1 supports (Kbps): 32, 48, 56, 64, 128, 192, 256, 384 KHS.2 supports (Kbps): ... KHSU.1/2 support (Kbps): 16, 32, 64. KHS.703 support (Kbps): 64. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), bps300(2), bps600(3), bps1200(4), bps2400(5), bps4800(6), bps7200(7), bps8000(8), bps9600(9), bps12000(10), bps14400(11), bps16000(12), bps16800(13), bps19200(14), bps21600(15), bps24000(16), bps26400(17), bps28800(18), bps31200(19), bps32000(20), bps33600(21), bps36000(22), bps38400(23), bps40800(24), bps43200(25), bps45600(26), bps48000(27), bps50400(28), bps52800(29), bps55200(30), bps56000(31), bps57600(32), bps60000(33), bps62400(34), bps64000(35), bps64800(36), bps67200(37), bps69600(38), bps72000(39), bps74400(40), bps76800(41), bps79200(42), bps81600(43), bps84000(44), bps86400(45), bps88800(46), bps91200(47), bps93600(48), bps96000(49), bps98400(50), bps100800(51), bps103200(52), bps105600(53), bps108000(54), bps110400(55), bps112800(56), bps115200(57), bps117600(58), bps120000(59), bps122400(60), bps124800(61), bps127200(62), bps128000(63), bps129600(64), bps134400(65), bps139200(66), bps144000(67), bps148800(68), bps153600(69), bps158400(70), bps163200(71), bps168000(72), bps172800(73), bps177600(74), bps182400(75), bps187200(76), bps192000(77), bps196800(78), bps201600(79), bps206400(80), bps211200(81), bps216000(82), bps220800(83), bps225600(84), bps230400(85), bps235200(86), bps240000(87), bps244800(88), bps249600(89), bps254400(90), bps256000(91), bps259200(92), bps264000(93), bps268800(94), bps273600(95), bps278400(96), bps283200(97), bps288000(98), bps292800(99), bps297600(100), bps302400(101), bps307200(102), bps316800(103), bps326400(104), bps336000(105), bps345600(106), bps355200(107), bps364800(108), bps374400(109), bps384000(110), bps393600(111), bps403200(112), bps412800(113), bps422400(114), bps432000(115), bps441600(116), bps451200(117), bps460800(118), bps470400(119), bps480000(120), bps489600(121), bps499200(122), bps508800(123), bps518400(124), bps528000(125), bps537600(126), bps547200(127), bps556800(128), bps566400(129), bps576000(130), bps585600(131), bps595200(132), bps604800(133), bps614400(134) | ||
| prtHsLsUType | 1.3.6.1.4.1.164.3.6.3.2.1.1.12 | ||
| U Interface Type. Applicable for KHSU.1/2 cards. The value will be the same for B1 and B2 pair; B3 and B4. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), regular(2), type1(3) | ||
| prtTreMbe | 1.3.6.1.4.1.164.3.6.3.3 | ||
| OBJECT IDENTIFIER | |||
| prtTreMbeTable | 1.3.6.1.4.1.164.3.6.3.3.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. Parameters for the channels of the TRE and MBE cards: KTRE, KMBE, KMBE/NEW. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtTreMbeEntry | |||
| prtTreMbeEntry | 1.3.6.1.4.1.164.3.6.3.3.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtTreMbeEntry | |||
| prtTreMbeCnfgIdx | 1.3.6.1.4.1.164.3.6.3.3.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtTreMbeIdx | 1.3.6.1.4.1.164.3.6.3.3.2.1.2 | ||
| A unique port identifier within the card. Slot*100+11 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTreMbeSlt | 1.3.6.1.4.1.164.3.6.3.3.2.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| prtTreMbeLan | 1.3.6.1.4.1.164.3.6.3.3.2.1.4 | ||
| This attribute indicates whether the TRE/MBE port is operated as main or remote bridge. Default=remote. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), main(2), remote(3) | ||
| prtTreMbeLanRate | 1.3.6.1.4.1.164.3.6.3.3.2.1.5 | ||
| This attribute indicates the Rate of the TRE port in Mbit/sec. Default-r4M. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r4M(2), r16M(3) | ||
| prtTreMbeLinkSpeed | 1.3.6.1.4.1.164.3.6.3.3.2.1.6 | ||
| The Link Speed. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), bps9600(2), bps19200(3), bps28800(4), bps38400(5), bps48000(6), bps57600(7), bps67200(8), bps76800(9), bps86400(10), bps96000(11), bps105600(12), bps115200(13), bps124800(14), bps128000(15), bps160000(16), bps192000(17), bps224000(18), bps240000(19), bps272000(20), bps304000(21), bps336000(22), bps368000(23) | ||
| prtVoiceFax | 1.3.6.1.4.1.164.3.6.3.4 | ||
| OBJECT IDENTIFIER | |||
| prtVoiceFaxTable | 1.3.6.1.4.1.164.3.6.3.4.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. Parameters for the channels of the Voice and Fax channels. Cards: KVC.1/E&M, KVC.1/FXO, KVC.1/FXS, KVC.1M/E&M, KVC.1M/FXO, KVC.1M/FXS, KVC.1M/FXSW, KVC.2/E&M, KVC.2/FXO, KVC.2/FXS, KVC.2/1/E&M,KVC.2/1/FXO,KVC.2/1/FXS, KVC.3/E&M, KVC.3/FXO, KVC.3/FXS, KVC.3/S0 KVF.1/E&M, KVF.1/FXO, KVF.1/FXS, KVF.3/E&M, KVF.3/FXO, KVF.3/FXS, KVF.4/E&M, KVF.4/FXO, KVF.4/FXS, KVF.4/FXSW, KVF.4/S0, KVF.4/FXO3, KVF.4/FXS3, KVF.4/NS0 KVF.5 family, KVF.6 family, KVF.8 family. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtVoiceFaxEntry | |||
| prtVoiceFaxEntry | 1.3.6.1.4.1.164.3.6.3.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtVoiceFaxEntry | |||
| prtVoiceFaxCnfgIdx | 1.3.6.1.4.1.164.3.6.3.4.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg (1..100) being accessed. Idx 255 relates to the TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtVoiceFaxIdx | 1.3.6.1.4.1.164.3.6.3.4.1.1.2 | ||
| A unique identifier of the port, within the card. Slot*100+Ch external ports: Ch=1..10 internal ports (sub-channels): Ch=11..20. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtVoiceFaxSlt | 1.3.6.1.4.1.164.3.6.3.4.1.1.3 | ||
| This attribute indicates a unique number to identify the slot where the card is inserted in. In the 2104 Unit the entries kmxIO5(111)..kmxIO12(118) are not valid. | |||
| OBJECT-TYPE | |||
| INTEGER | kmxIO1(107), kmxIO2(108), kmxIO3(109), kmxIO4(110), kmxIO5(111), kmxIO6(112), kmxIO7(113), kmxIO8(114), kmxIO9(115), kmxIO10(116), kmxIO11(117), kmxIO12(118) | ||
| prtVoiceFaxTransGain | 1.3.6.1.4.1.164.3.6.3.4.1.1.4 | ||
| Transmit gain in dBm. A value of 255 is for notApplicable. The value will be: real value+50dBm (in order to avoid negative values). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtVoiceFaxReceiveGain | 1.3.6.1.4.1.164.3.6.3.4.1.1.5 | ||
| Receive gain in dBm. A value of 255 is for notApplicable. The value will be: real value+50dBm (in order to avoid negative values). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtVoiceFaxWire | 1.3.6.1.4.1.164.3.6.3.4.1.1.6 | ||
| Applicable only for E&M cards. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), w2wire(2), w4wire(3) | ||
| prtVoiceFaxTimeOut | 1.3.6.1.4.1.164.3.6.3.4.1.1.7 | ||
| Fax timeout in seconds. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), manual(2), sec30(3), sec60(4), sec90(5) | ||
| prtVoiceFaxEchoCanceler | 1.3.6.1.4.1.164.3.6.3.4.1.1.8 | ||
| Echo canceler activation. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| prtVoiceFaxSpeed | 1.3.6.1.4.1.164.3.6.3.4.1.1.9 | ||
| The channel speed. For KVF.6 and KVF.8 cards, each value will represent [4 x value], since each channel (Internal or External) is comprised of 4 sub-channels having the selected value. | |||
| OBJECT-TYPE | |||
| INTEGER | notConnected(1), bps4800(2), bps6400(3), bps7200(4), bps8000(5), bps9600(6), bps12800(7), bps16000(8), bps24000(9), bps32000(10), bps64000(11), bps11200(12) | ||
| prtVoiceFaxMeterRate | 1.3.6.1.4.1.164.3.6.3.4.1.1.10 | ||
| This entry is valid to KVF.4/FXO3 and KVF.4/FXS3. Meter Rate means rate of Call Meter in Public Phones, in KHz units. Must be equal for both channels. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r16Khz(2), r12Khz(3) | ||
| prtVoiceFaxCodingLaw | 1.3.6.1.4.1.164.3.6.3.4.1.1.11 | ||
| Coding Law. This entry is valid for KVF.4/NS0 external channel and KVF.6 internal channels. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), aLaw(2), uLaw(3) | ||
| prtVoiceFaxOperMode | 1.3.6.1.4.1.164.3.6.3.4.1.1.12 | ||
| Operation Mode. This parameter is valid for KVF.6 and KVF.8 family. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), voiceANDfax(2), voice(3), voiceAndFaxAndData(4) | ||
| prtVoiceFaxSigInOutband | 1.3.6.1.4.1.164.3.6.3.4.1.1.13 | ||
| This object is applicable for KVF.4/FXO3, KVF.4/FXS3, KVF.8 family cards. For KVF.4/FXO3, KVF.4/FXS3: Octet 1 for Receive parameters. Octet 2 for Transmit parameters. It represents 4 parameters, in each Octet : Bit 7 6 5 4 3 2 1 0 |_____| |_____| |_____| |_____| MSB Spare On/Off Hook Metering Polarity LSB Each parameter's bits represent: 00 = NC 01 = Inband(A/B) 10 = Outband(A) 11 = Outband(B) For KVF.8 family: It represents 4 parameters, by 2 Octets : General Bit Code- MSB nibble, On/Off Hook Bit Code- nibble, Metering Bit Code- nibble, Polarity Bit Code- LSB nibble. Each of General, On/Off Hook, Metering, Polarity Bit Code nibble represents: 0 hex = 0000 = 0 1 hex = 0001 = 1 2 hex = 0010 = A bit 3 hex = 0011 = B bit 4 hex = 0100 = C bit 5 hex = 0101 = D bit 6 hex = 0110 = A bit inverse 7 hex = 0111 = B bit inverse 8 hex = 1000 = C bit inverse 9 hex = 1001 = D bit inverse A-E hex - not used (invalid values) When the object is not applicable, 0 Octets will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| prtVoiceFaxTsGroup | 1.3.6.1.4.1.164.3.6.3.4.1.1.14 | ||
| Ts Assignment group. Each KVF.6 internal channel should have a different value. 's21s22s23s24' = TSs: 21, 22, 23, 24 For KVF.6/E1/16, KVF.6/E1/31 values: 2..9 are applicable. For KVF.6/T1/12, KVF.6/T1/24 values: 2..7 are applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), s1s2s3s4(2), s5s6s7s8(3), s9s10s11s12(4), s13s14s15s16(5), s17s18s19s20(6), s21s22s23s24(7), s25s26s27s28(8), s29s30s31(9) | ||
| prtVoiceFaxRxFaxGain | 1.3.6.1.4.1.164.3.6.3.4.1.1.15 | ||
| FAX Receive gain in dBm. The value will be: (real value*10)+500dBm (in order to avoid negative and fractional values). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtVoiceFaxSigHold | 1.3.6.1.4.1.164.3.6.3.4.1.1.16 | ||
| Signal Hold in [sec]. Applicable for all KVF.4 cards except S0/NS0. When a ML fails, instead of interrupting immediately a conversation and connecting it again when ML operation is resumed, user can select to Hold the signal a few seconds before interruption (ML operation may return during this time). sec0 = No Hold = 0 sec sec10= 10 sec hold. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), sec0(2), sec10(3) | ||
| prtVoiceFaxIfSignaling | 1.3.6.1.4.1.164.3.6.3.4.1.1.17 | ||
| Applicable only for KVF.8/FXO, KVF.8/FXS cards. Interface Analog Signaling. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), loopStart(2), groundStart(3), winkStart(4) | ||
| prtVoiceFaxEMTypes | 1.3.6.1.4.1.164.3.6.3.4.1.1.18 | ||
| Applicable only for KVF.8/E&M card. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), em1(2), em2(3), em3(4), ssdc5(5) | ||
| prtVoiceFaxRingFrequency | 1.3.6.1.4.1.164.3.6.3.4.1.1.19 | ||
| Applicable only for KVF.8/E&M card. The Ringing Frequency units will be in Hz. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), f16dot7Hz(2), f20Hz(3), f25Hz(4), f50Hz(5) | ||
| prtVoiceFaxSignalingStatus | 1.3.6.1.4.1.164.3.6.3.4.1.1.20 | ||
| For KM-2100 this parameter should be Read Only. This object is applicable for KVF.6 and KVF.5 family cards. It shows the status (0 or 1) of each Signaling Bit (A, B, C, D), for each TS of a TS Group (according to it's position in the group). Each nibble represent a TS from the 'TS Group' selected for the channel (two Octets represents 4 TSs of each group): Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 |________| |________| |________| |________| MSB TS i+3 TS i+2 TS i+1 TS i LSB It represents 4 parameters for each TS: TS-i TS-i+1 .. 0 - A bit 4 - A bit 1 - B bit 5 - B bit 2 - C bit 6 - C bit 3 - D bit 7 - D bit When the object is not applicable, 0 Octets will be sent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..2) | ||
| imx | 1.3.6.1.4.1.164.3.7 | ||
| OBJECT IDENTIFIER | |||
| systemImx | 1.3.6.1.4.1.164.3.7.1 | ||
| OBJECT IDENTIFIER | |||
| generalImx | 1.3.6.1.4.1.164.3.7.1.1 | ||
| OBJECT IDENTIFIER | |||
| sysGenClearAlarm | 1.3.6.1.4.1.164.3.7.1.1.1 | ||
| Clear the alarm buffer. The agent resets the variable automatically to off. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| sysGenAlarmBuffTable | 1.3.6.1.4.1.164.3.7.1.1.2 | ||
| The alarm buffer of the imx. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysGenAlarmBuffEntry | |||
| sysGenAlarmBuffEntry | 1.3.6.1.4.1.164.3.7.1.1.2.1 | ||
| An entry in table sysGenAlarmBuffTable. | |||
| OBJECT-TYPE | |||
| SysGenAlarmBuffEntry | |||
| sysGenAlarmBuffIndex | 1.3.6.1.4.1.164.3.7.1.1.2.1.1 | ||
| The index of the alarm buffer Table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| sysGenAlarmDescr | 1.3.6.1.4.1.164.3.7.1.1.2.1.2 | ||
| The description of the alarm. Up to 80 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| sysGenClearLog | 1.3.6.1.4.1.164.3.7.1.1.3 | ||
| Clear the log buffer. The agent resets the variable automatically to off. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| sysGenLogTable | 1.3.6.1.4.1.164.3.7.1.1.4 | ||
| The call log buffer of the imx. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysGenLogEntry | |||
| sysGenLogEntry | 1.3.6.1.4.1.164.3.7.1.1.4.1 | ||
| An entry in table sysGenLogTable. | |||
| OBJECT-TYPE | |||
| SysGenLogEntry | |||
| sysGenLogIndex | 1.3.6.1.4.1.164.3.7.1.1.4.1.1 | ||
| The index of the log Table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..100 | ||
| sysGenLogDescr | 1.3.6.1.4.1.164.3.7.1.1.4.1.2 | ||
| The description of the entry in the log buffer. Up to 80 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| profilesImx | 1.3.6.1.4.1.164.3.7.1.2 | ||
| OBJECT IDENTIFIER | |||
| callProfileImx | 1.3.6.1.4.1.164.3.7.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| sysCallProfileTable | 1.3.6.1.4.1.164.3.7.1.2.1.1 | ||
| A table containing call profile parameters. There are 40 call profiles. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SysCallProfileEntry | |||
| sysCallProfileEntry | 1.3.6.1.4.1.164.3.7.1.2.1.1.1 | ||
| An entry in table sysCallProfileTable. | |||
| OBJECT-TYPE | |||
| SysCallProfileEntry | |||
| sysCallProfileIndex | 1.3.6.1.4.1.164.3.7.1.2.1.1.1.1 | ||
| A running index for the table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..40 | ||
| sysCallProfileConnectCmd | 1.3.6.1.4.1.164.3.7.1.2.1.1.1.2 | ||
| On(2) - Connect the call profile. The agent will automatically reset the variable to off(1) . | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| sysCallProfileDisconnectCmd | 1.3.6.1.4.1.164.3.7.1.2.1.1.1.3 | ||
| On(2) - Disconnect the call profile. The agent will automatically reset the variable to off(1). | |||
| OBJECT-TYPE | |||
| INTEGER | off(1), on(2) | ||
| sysCallProfileIncrBwCmd | 1.3.6.1.4.1.164.3.7.1.2.1.1.1.4 | ||
| Increment bandwidth of a call. The number of channels to increment 1..6. The agent will automatically reset the variable to 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..6 | ||
| sysCallProfileDecrBwCmd | 1.3.6.1.4.1.164.3.7.1.2.1.1.1.5 | ||
| Decrement bandwidth of a call. The number of channels to decrement 1..6. The agent will automatically reset the variable to 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..6 | ||
| portImx | 1.3.6.1.4.1.164.3.7.2 | ||
| OBJECT IDENTIFIER | |||
| userPortImx | 1.3.6.1.4.1.164.3.7.2.1 | ||
| OBJECT IDENTIFIER | |||
| prtCnfgTable | 1.3.6.1.4.1.164.3.7.2.1.1 | ||
| A table containing configuration parameters for the user ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtCnfgEntry | |||
| prtCnfgEntry | 1.3.6.1.4.1.164.3.7.2.1.1.1 | ||
| An entry in table prtCnfgTable. | |||
| OBJECT-TYPE | |||
| PrtCnfgEntry | |||
| prtIndex | 1.3.6.1.4.1.164.3.7.2.1.1.1.1 | ||
| The user port index. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..2 | ||
| prtCnfgDecrBwChNum | 1.3.6.1.4.1.164.3.7.2.1.1.1.2 | ||
| Decrement the port bandwidth by the specified number of channels. The agent resets the variable to 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..6 | ||
| prtCnfgIncrBwChNum | 1.3.6.1.4.1.164.3.7.2.1.1.1.3 | ||
| Increment the port bandwidth by the specified number of channels. The agent resets the variable to 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..6 | ||
| prtCnfgDisconnect | 1.3.6.1.4.1.164.3.7.2.1.1.1.4 | ||
| Disconnect the port (on(1)). The agent resets the variable to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| prtCnfgActivateLoop | 1.3.6.1.4.1.164.3.7.2.1.1.1.5 | ||
| Activate the desired loop on the port. The agent will reset the variable to none(1). | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), local(2), remote(3), bonding(4) | ||
| prtCnfgClearLoop | 1.3.6.1.4.1.164.3.7.2.1.1.1.6 | ||
| Clear the desired loop from the port. The agent will reset the variable to none(1) | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), local(2), remote(3), bonding(4), all(5) | ||
| prtCnfgLoopStatus | 1.3.6.1.4.1.164.3.7.2.1.1.1.7 | ||
| The loop status at this port. The variable is a sum of 2**n where n is as follows: 0 - Local Loop is on. 1 - Remote Loop is on. 2 - BONDING Loop is on. If the variable is 0, there is no active loop. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| supervisoryPortImx | 1.3.6.1.4.1.164.3.7.2.2 | ||
| OBJECT IDENTIFIER | |||
| prtSpUsageImx | 1.3.6.1.4.1.164.3.7.2.2.1 | ||
| The supervisory port terminal usage definition. | |||
| OBJECT-TYPE | |||
| INTEGER | nmsSlip(2), terminal(3) | ||
| channelImx | 1.3.6.1.4.1.164.3.7.4 | ||
| OBJECT IDENTIFIER | |||
| channelCnfgTable | 1.3.6.1.4.1.164.3.7.4.1 | ||
| A table containing configuration parameters for the channels. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChannelCnfgEntry | |||
| channelCnfgEntry | 1.3.6.1.4.1.164.3.7.4.1.1 | ||
| An entry in table channelCnfgTable. | |||
| OBJECT-TYPE | |||
| ChannelCnfgEntry | |||
| chIndex | 1.3.6.1.4.1.164.3.7.4.1.1.1 | ||
| The channel index. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..6 | ||
| chCnfgUnlock | 1.3.6.1.4.1.164.3.7.4.1.1.2 | ||
| Unlock the channel (on). The agent resets the variable to off. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| chCnfgPing | 1.3.6.1.4.1.164.3.7.4.1.1.3 | ||
| Ping the channel (on). The agent resets the variable to off. | |||
| OBJECT-TYPE | |||
| INTEGER | on(1), off(2) | ||
| channelStatTable | 1.3.6.1.4.1.164.3.7.4.2 | ||
| A table containing status and statistics information for the channels. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ChannelStatEntry | |||
| channelStatEntry | 1.3.6.1.4.1.164.3.7.4.2.1 | ||
| An entry in table channelStatTable. | |||
| OBJECT-TYPE | |||
| ChannelStatEntry | |||
| chStatOperStatus | 1.3.6.1.4.1.164.3.7.4.2.1.1 | ||
| The operational state of the channel based on a ping operation. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), engaged(3), notDedicated(4) | ||
| radBridges | 1.3.6.1.4.1.164.4 | ||
| OBJECT IDENTIFIER | |||
| genBridge | 1.3.6.1.4.1.164.4.1 | ||
| OBJECT IDENTIFIER | |||
| radBridgeAction | 1.3.6.1.4.1.164.4.1.1 | ||
| This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions are not currently implemented. Not all actions can be performed on all bridges. | |||
| OBJECT-TYPE | |||
| INTEGER | reset(1), sendNetworkTab(2), deleteNetworkTab(3), sendRoutingTab(4), deleteRoutinTab(5), sendLanTab(6), deleteLanTab(7), deleteArpTab(8), sendArpTab(9), deleteRouteTab(10), sendRouteTab(11), deactivateAllMasks(12), saveAllActiveMasks(13), loadAndActivateAllMasksFromNVRAM(14), clearAllMasksFromNVRAM(15), defaultConfig(16), resetNVRAM(17), clearIPNVRAM(18), noOp(255) | ||
| radBridgeInactiveArpTimeOut | 1.3.6.1.4.1.164.4.1.2 | ||
| This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskTable | 1.3.6.1.4.1.164.4.1.3 | ||
| Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement consisting of up to three mask definitions and an action defined by radBridgeMaskOper. Different types of mask entries are supported, as defined by radBridgeMaskType. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeMaskEntry | |||
| radBridgeMaskEntry | 1.3.6.1.4.1.164.4.1.3.1 | ||
| An entry in table radBridgeMaskTable. | |||
| OBJECT-TYPE | |||
| RadBridgeMaskEntry | |||
| radBridgeMaskType | 1.3.6.1.4.1.164.4.1.3.1.1 | ||
| Defines the type of mask entry. | |||
| OBJECT-TYPE | |||
| INTEGER | tx(1), rx(2), compress(3), priority(4), loadSharing(5), facs(6), codConnect(7), codDisconnect(8) | ||
| radBridgeMaskIfIndex | 1.3.6.1.4.1.164.4.1.3.1.2 | ||
| Specifies the if Index of the interface to which the mask is applied. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskNum | 1.3.6.1.4.1.164.4.1.3.1.3 | ||
| The Mask entry number, defined by its line number in the mask table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskDest | 1.3.6.1.4.1.164.4.1.3.1.4 | ||
| Specifies the type of destination address carried by the frame to which the mask will be applied. Unassigned-condition deactivates the mask entry. | |||
| OBJECT-TYPE | |||
| INTEGER | unassigned-cond(1), broadcast-msge(2), multicast-msge(3), all-msge(4), none(5) | ||
| radBridgeMaskPat1 | 1.3.6.1.4.1.164.4.1.3.1.5 | ||
| Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskActiveBit1 | 1.3.6.1.4.1.164.4.1.3.1.6 | ||
| Specifies the positions of the wild card characters (*) in the radBridgeMaskPat1 field. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskFrom1 | 1.3.6.1.4.1.164.4.1.3.1.7 | ||
| Offset base of radBridgeMaskPat1 within the frame. Net can be in some cases the data start point. | |||
| OBJECT-TYPE | |||
| INTEGER | mac(1), llc(2), net(3) | ||
| radBridgeMaskOffset1 | 1.3.6.1.4.1.164.4.1.3.1.8 | ||
| Specifies the radBridgeMaskPat1 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm1.The mask offset is an even decimal number in the range of 0 to 1518. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskCond1 | 1.3.6.1.4.1.164.4.1.3.1.9 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that matches the content of radBridgeMaskPat1. false - Condition is valid if at the position specified by radBridgeMaskOffset1 the packet contains data that does not match the content of radBridgeMaskPat1. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| radBridgeMaskPat2 | 1.3.6.1.4.1.164.4.1.3.1.10 | ||
| Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskActiveBit2 | 1.3.6.1.4.1.164.4.1.3.1.11 | ||
| Specifies the positions of the wild card characters (*) in the radBridgeMaskPat2 field. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskFrom2 | 1.3.6.1.4.1.164.4.1.3.1.12 | ||
| Offset base of radBridgeMaskPat2 within the frame. Net can be in some cases the data start point. | |||
| OBJECT-TYPE | |||
| INTEGER | mac(1), llc(2), net(3) | ||
| radBridgeMaskOffset2 | 1.3.6.1.4.1.164.4.1.3.1.13 | ||
| Specifies the radBridgeMaskPat2 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm2.The mask offset is an even decimal number in the range of 0 to 1518. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskCond2 | 1.3.6.1.4.1.164.4.1.3.1.14 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that matches the content of radBridgeMaskPat2. false - Condition is valid if at the position specified by radBridgeMaskOffset2 the packet contains data that does not match the content of radBridgeMaskPat2. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| radBridgeMaskPat3 | 1.3.6.1.4.1.164.4.1.3.1.15 | ||
| Describes the mask field which is either a 16 bit binary pattern, or four digit hexadecimal pattern. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskActiveBit3 | 1.3.6.1.4.1.164.4.1.3.1.16 | ||
| Specifies the positions of the wild card characters (*) in the radBridgeMaskPat3 field. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeMaskFrom3 | 1.3.6.1.4.1.164.4.1.3.1.17 | ||
| Offset base of radBridgeMaskPat3 within the frame. Net can be in some cases the data start point. | |||
| OBJECT-TYPE | |||
| INTEGER | mac(1), llc(2), net(3) | ||
| radBridgeMaskOffset3 | 1.3.6.1.4.1.164.4.1.3.1.18 | ||
| Specifies the radBridgeMaskPat3 offset within the frame (in bytes) from the base defined in by radBridgeMaskForm3. The mask offset is an even decimal number in the range of 0 to 1518. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeMaskCond3 | 1.3.6.1.4.1.164.4.1.3.1.19 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that matches the content of radBridgeMaskPat3 false - Condition is valid if at the position specified by radBridgeMaskOffset3 the packet contains data that does not match the content of radBridgeMaskPat3. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| radBridgeMaskOper | 1.3.6.1.4.1.164.4.1.3.1.20 | ||
| The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. | |||
| OBJECT-TYPE | |||
| INTEGER | block(1), forward(2), route(3), forward-route(4), high-priority(5), noOp(6), delete(7) | ||
| radBridgeCOD | 1.3.6.1.4.1.164.4.1.4 | ||
| OBJECT IDENTIFIER | |||
| radBridgeCODParamTable | 1.3.6.1.4.1.164.4.1.4.1 | ||
| The table of COD parameters | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeCODEntry | |||
| radBridgeCODEntry | 1.3.6.1.4.1.164.4.1.4.1.1 | ||
| Each radBridgeCODEntry consists of the following parameters | |||
| OBJECT-TYPE | |||
| RadBridgeCODEntry | |||
| radBridgeCODIfIndex | 1.3.6.1.4.1.164.4.1.4.1.1.1 | ||
| The interface to which this COD entry is applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODManualConnect | 1.3.6.1.4.1.164.4.1.4.1.1.2 | ||
| The management station can start connection manually by setting this parameter | |||
| OBJECT-TYPE | |||
| INTEGER | connect(1), disconnect(2) | ||
| radBridgeCODMode | 1.3.6.1.4.1.164.4.1.4.1.1.3 | ||
| In answer mode only one incoming call may be accepted at a time. Other nodes attempting to access the local modem will receive a busy signal until the connection is terminated. (Answer mode has no difficulty supporting multiple remote connections to one local port, as blocking multiple incoming calls is just a modem function. Originate mode, on the other hand will only support a single local port to remote port connection). The disable parameter disables the COD utility for this interface. Choosing any other mode will enable the COD utility. | |||
| OBJECT-TYPE | |||
| INTEGER | answer(1), originate(2), disable(3), answerAndOriginate(4) | ||
| radBridgeCODConnectDelay | 1.3.6.1.4.1.164.4.1.4.1.1.4 | ||
| The connect delay defines the minimum time period that the link must stay disconnected, between 2 succesive connections (in seconds). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODisConnectDelay | 1.3.6.1.4.1.164.4.1.4.1.1.5 | ||
| The disconnect delay defines the minimum time period the link must stay connected, between 2 succesive disconnections (in seconds). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODImplicitSwitch | 1.3.6.1.4.1.164.4.1.4.1.1.6 | ||
| The inplicit switch allows the user to ignore implicit triggers provided by the COD software. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| radBridgeCODNumAccess | 1.3.6.1.4.1.164.4.1.4.1.1.7 | ||
| The number of successful connections that have been established since the COD has been reset. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeCODTotalConnecTime | 1.3.6.1.4.1.164.4.1.4.1.1.8 | ||
| The sum of all the connect time intervals since the COD was reset. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODTimeTriggerTable | 1.3.6.1.4.1.164.4.1.4.2 | ||
| The table of COD parameters | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeCODTimeTriggerEntry | |||
| radBridgeCODTimeTriggerEntry | 1.3.6.1.4.1.164.4.1.4.2.1 | ||
| Each radBridgeCODTimeTriggerEntry consists of the following parameters | |||
| OBJECT-TYPE | |||
| RadBridgeCODTimeTriggerEntry | |||
| radBridgeCODTimeIfIndex | 1.3.6.1.4.1.164.4.1.4.2.1.1 | ||
| The interface to which this COD Time Trigger entry is applicable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODDay | 1.3.6.1.4.1.164.4.1.4.2.1.2 | ||
| The day of the week in which the dial up connection operates. | |||
| OBJECT-TYPE | |||
| INTEGER | mon(1), tue(2), wed(3), thu(4), fri(5), sat(6), sun(7) | ||
| radBridgeCODTimeTriggerNum | 1.3.6.1.4.1.164.4.1.4.2.1.3 | ||
| Every day of the week the user can configure 3 dial up connections. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..3 | ||
| radBridgeCODTimeTriggerFrom | 1.3.6.1.4.1.164.4.1.4.2.1.4 | ||
| Time to start Dial Up connection, in format hh:mm. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| radBridgeCODTimeTriggerTo | 1.3.6.1.4.1.164.4.1.4.2.1.5 | ||
| Time to terminate Dial Up connection, in format HH:MM. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| radBridgeCODTimeTriggerStatus | 1.3.6.1.4.1.164.4.1.4.2.1.6 | ||
| The status of a table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), invalid(2) | ||
| radBridgeCODTraffic | 1.3.6.1.4.1.164.4.1.4.3 | ||
| OBJECT IDENTIFIER | |||
| radBridgeCODTrafficTable | 1.3.6.1.4.1.164.4.1.4.3.1 | ||
| The table of COD Traffic trigger | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeCODTrafficEntry | |||
| radBridgeCODTrafficEntry | 1.3.6.1.4.1.164.4.1.4.3.1.1 | ||
| Each radBridgeCODTrafficEntry consists of the following parameters. | |||
| OBJECT-TYPE | |||
| RadBridgeCODTrafficEntry | |||
| radBridgeCODProtocolType | 1.3.6.1.4.1.164.4.1.4.3.1.1.1 | ||
| The Protocol Type of the Traffic Table | |||
| OBJECT-TYPE | |||
| INTEGER | ip(1), ipx(2), other(3) | ||
| radBridgeCODTrafficTriggerStatus | 1.3.6.1.4.1.164.4.1.4.3.1.1.2 | ||
| Command of Status of the Protocol Traffic Trigger | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| radBridgeCODRemoteIPAddr | 1.3.6.1.4.1.164.4.1.4.3.2 | ||
| This is the Remote IP Address | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radBridgeCODIPMask | 1.3.6.1.4.1.164.4.1.4.3.3 | ||
| This is the Mask of the Remote IP Address | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| radBridgeCODTrafficTriggerProtType | 1.3.6.1.4.1.164.4.1.4.3.4 | ||
| Protocol Type for the User Defined Protocol Traffic Trigger (3). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radBridgeCODCondTable | 1.3.6.1.4.1.164.4.1.4.4 | ||
| The table of COD Condition parameters | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeCODCondEntry | |||
| radBridgeCODCondEntry | 1.3.6.1.4.1.164.4.1.4.4.1 | ||
| Each radBridgeCODCondEntry consists of the following parameters | |||
| OBJECT-TYPE | |||
| RadBridgeCODCondEntry | |||
| radBridgeCODCondIfIndex | 1.3.6.1.4.1.164.4.1.4.4.1.1 | ||
| The interface, this COD entry is applicable to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODOriginateConnectCondition | 1.3.6.1.4.1.164.4.1.4.4.1.2 | ||
| This condition, allows the user to specify the condition under which the link is connected. The options are onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=connect). | |||
| OBJECT-TYPE | |||
| INTEGER | onPowerOn(1), whenAnyStationOnLan(2), onTraffic(3), onManualConnect(4) | ||
| radBridgeCODOriginateDisConnectCondition | 1.3.6.1.4.1.164.4.1.4.4.1.3 | ||
| This condition allows the user to specify the condition under which the link is disconnected. The options are: noStationOnLan - When there is no station on lan. Counts 15 minutes from the point the last frame from lan has been received. If no frame have been transmitted on lan by the end of this period, disconnect the connection. onTraffic - On traffic. The user can specify the condition/s for disconnection. The disconnection will be defined in CODSpecificOnTrafficConditionOID . onDelayFromConnectionOnRequest - On Delay From Connection On Request . The delay time period will be defined in CODOriginateDisConnectDelay . onManualDisConnect - depends on radBridgeCODManualConnect OBJECT-TYPE (=disconnect). | |||
| OBJECT-TYPE | |||
| INTEGER | noStationOnLan(1), onTraffic(2), onDelayFromConnectionOnRequest(3), onManualDisConnect(4) | ||
| radBridgeCODOriginateDisConnectDelay | 1.3.6.1.4.1.164.4.1.4.4.1.4 | ||
| Delay time in seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCODAnswerConnectCondition | 1.3.6.1.4.1.164.4.1.4.4.1.5 | ||
| CODCondAnswerConnect allows the user to specify the condition under which the link is connected. The options are: onPowerOn - On power on. whenAnyStationOnLan - When any station on lan. onTraffic - On traffic. The user can specify the condition/s for connection. The connection will be defined in CODSpecificOnTrafficConditionOID . onManualConnect - depends on radBridgeCODManualConnect OBJECT-TYPE . | |||
| OBJECT-TYPE | |||
| INTEGER | onPowerOn(1), whenAnyStationOnLan(2), onTraffic(3), onManualConnect(4) | ||
| radBridgeCODSpecificOnTrafficOIDCondition | 1.3.6.1.4.1.164.4.1.4.4.1.6 | ||
| A reference to a specific entry in the radBridgeMaskTable, which describes the particular COD condition . If Connect or Disconnect Conditions are not onTraffic, its value should be set to the OBJECT IDENTIFIER { 0 0 }. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| radBridgeCODDisConnectMinimunFramesNumber | 1.3.6.1.4.1.164.4.1.4.4.1.7 | ||
| Frames rate. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPX | 1.3.6.1.4.1.164.4.1.5 | ||
| OBJECT IDENTIFIER | |||
| radBridgeIPXdriver | 1.3.6.1.4.1.164.4.1.5.1 | ||
| OBJECT IDENTIFIER | |||
| radBridgeIPXForwarding | 1.3.6.1.4.1.164.4.1.5.1.1 | ||
| The indication of whether this entity is acting as an IPX gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IPX gateways forward datagrams. IPX hosts do not. Note that changing this parameter requiers RESET of the router. | |||
| OBJECT-TYPE | |||
| INTEGER | forwarding(1), not-forwarding(2) | ||
| radBridgeIPXRip | 1.3.6.1.4.1.164.4.1.5.2 | ||
| OBJECT IDENTIFIER | |||
| radBridgeIPXRipOutPackets | 1.3.6.1.4.1.164.4.1.5.2.1 | ||
| The total number of packets transmitted by RIP. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXRipInPackets | 1.3.6.1.4.1.164.4.1.5.2.2 | ||
| The total number of packets received by RIP. This will include any packets that are subsequently discarded. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXRipInDiscards | 1.3.6.1.4.1.164.4.1.5.2.3 | ||
| The number of received packets discarded by RIP. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXRipTblNoOfEntries | 1.3.6.1.4.1.164.4.1.5.2.4 | ||
| The max number of entries that exist in the RIP routing table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipTblBcastTrigUpdateInterval | 1.3.6.1.4.1.164.4.1.5.2.5 | ||
| The default time interval (in seconds)between triggered RIP updates on a broadcast type interface. A triggered update occurs when a change is detected in the routing database. This time interval delays the broadcasting of these updates so that changes on the network will not result in a lot of triggered updates. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipTable | 1.3.6.1.4.1.164.4.1.5.2.6 | ||
| The routing table used by RIP to calculate routes to remote desination networks. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeIPXRipTableEntry | |||
| radBridgeIPXRipTableEntry | 1.3.6.1.4.1.164.4.1.5.2.6.1 | ||
| The routing information for one of this entity's destination networks. | |||
| OBJECT-TYPE | |||
| RadBridgeIPXRipTableEntry | |||
| radBridgeIPXRipDestNetwork | 1.3.6.1.4.1.164.4.1.5.2.6.1.1 | ||
| The destination network address to which this entry's routing information pertains. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| radBridgeIPXRipPolicy | 1.3.6.1.4.1.164.4.1.5.2.6.1.2 | ||
| A value specifying the precidence of the route. A value of zero means that the route is the best route, a value of one means that the route is the second best route and so on. | |||
| OBJECT-TYPE | |||
| INTEGER | main(1), alternate(2) | ||
| radBridgeIPXRipForwardingRouter | 1.3.6.1.4.1.164.4.1.5.2.6.1.3 | ||
| The IPX node address of the next hop (router) for the entry's associated destination network. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| radBridgeIPXRipNIC | 1.3.6.1.4.1.164.4.1.5.2.6.1.4 | ||
| An interface identifier specifying what IPX interface the next hop can be found on. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipTickMetric | 1.3.6.1.4.1.164.4.1.5.2.6.1.5 | ||
| The metric, in terms of transit time, associated with the route given by the entry. This time is in terms of 1/18ths of a second. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipHopMetric | 1.3.6.1.4.1.164.4.1.5.2.6.1.6 | ||
| The metric, in terms of distance , associated with the route given by the entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipAgingTime | 1.3.6.1.4.1.164.4.1.5.2.6.1.7 | ||
| The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| radBridgeIPXRipValueStatus | 1.3.6.1.4.1.164.4.1.5.2.6.1.8 | ||
| The entry status value; whether the entry is permanent (added statically), reachable or unreachable. In the latter two cases it would be added by RIP. A semiDynamic entry is an entry enterd manualy by the user and can be updated by the router. | |||
| OBJECT-TYPE | |||
| INTEGER | static(1), dynamic(2), invalid(3), semiDynamic(4) | ||
| radBridgeIPXRipForwardType | 1.3.6.1.4.1.164.4.1.5.2.6.1.9 | ||
| The type of route. Note that local(2) refers to a route for which the next hop is the final destination; remote(3) refers to a route for which the next hop is not the final destination. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), local(2), remote(3) | ||
| radBridgeIPXRipInfTable | 1.3.6.1.4.1.164.4.1.5.2.7 | ||
| The RIP interface table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeIPXRipInfEntry | |||
| radBridgeIPXRipInfEntry | 1.3.6.1.4.1.164.4.1.5.2.7.1 | ||
| Each entry corresponds to one ifindex. | |||
| OBJECT-TYPE | |||
| RadBridgeIPXRipInfEntry | |||
| radBridgeIPXRipInfIfIndex | 1.3.6.1.4.1.164.4.1.5.2.7.1.1 | ||
| This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipInfBcastUpdate | 1.3.6.1.4.1.164.4.1.5.2.7.1.2 | ||
| The RIP periodic update interval, in seconds. Zero value corresponds to infinite interval. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXRipInfAgeMultiplier | 1.3.6.1.4.1.164.4.1.5.2.7.1.3 | ||
| The holding multiplier for information received in RIP periodic updates. Zero value corresponds to infinite aging time. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSap | 1.3.6.1.4.1.164.4.1.5.3 | ||
| OBJECT IDENTIFIER | |||
| radBridgeIPXSapOutPackets | 1.3.6.1.4.1.164.4.1.5.3.1 | ||
| The total number of packets transmitted by SAP. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXSapInPackets | 1.3.6.1.4.1.164.4.1.5.3.2 | ||
| The total number of packets received by SAP. This will include any packets that are subsequently discarded. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXSapInDiscards | 1.3.6.1.4.1.164.4.1.5.3.3 | ||
| The number of received packets discarded by SAP. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| radBridgeIPXSapTblNoOfEntries | 1.3.6.1.4.1.164.4.1.5.3.4 | ||
| The max number of entries that exist in the SAP Server Information table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapTblBcastTrigUpdateInterval | 1.3.6.1.4.1.164.4.1.5.3.5 | ||
| The default time interval (in seconds) between triggered SAP updates on a broadcast style interface. A triggered update occurs when a change is detected in the service database. This time interval delays the transmission of these updates so that changes on the network will not result in a lot of triggered updates. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapTable | 1.3.6.1.4.1.164.4.1.5.3.6 | ||
| The Server Information table is used by SAP to store information of services which are available on the internetwork. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeIPXSapTableEntry | |||
| radBridgeIPXSapTableEntry | 1.3.6.1.4.1.164.4.1.5.3.6.1 | ||
| The server information for one of this entity's server entries. | |||
| OBJECT-TYPE | |||
| RadBridgeIPXSapTableEntry | |||
| radBridgeIPXSapServerType | 1.3.6.1.4.1.164.4.1.5.3.6.1.1 | ||
| The type of the server for which this entry pertains. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapName | 1.3.6.1.4.1.164.4.1.5.3.6.1.2 | ||
| The name of the server for which this entry pertains. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(48) | ||
| radBridgeIPXSapNetwork | 1.3.6.1.4.1.164.4.1.5.3.6.1.3 | ||
| The IPX network address of the host on which this server exists. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| radBridgeIPXSapNode | 1.3.6.1.4.1.164.4.1.5.3.6.1.4 | ||
| The IPX node address of the host on which this server exists. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| radBridgeIPXSapSocket | 1.3.6.1.4.1.164.4.1.5.3.6.1.5 | ||
| The IPX socket number that is being used by the server to which this entry pertains. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapHopsToServer | 1.3.6.1.4.1.164.4.1.5.3.6.1.6 | ||
| The number of hops to the entity on which this server exists. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..16 | ||
| radBridgeIPXSapNIC | 1.3.6.1.4.1.164.4.1.5.3.6.1.7 | ||
| An Network Interface Card identifier specifying what IPX interface the next hop can be found on. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapAgingTime | 1.3.6.1.4.1.164.4.1.5.3.6.1.8 | ||
| The last time that the entry was updated. The time will be provided in terms of the MIB-I object sysUpTime. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| radBridgeIPXSapStatus | 1.3.6.1.4.1.164.4.1.5.3.6.1.9 | ||
| The status of the entry. | |||
| OBJECT-TYPE | |||
| INTEGER | permanent(1), dynamic(2), invalid(3), semiDynamic(4) | ||
| radBridgeIPXSapInfTable | 1.3.6.1.4.1.164.4.1.5.3.7 | ||
| The Sap interface table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeIPXSapInfEntry | |||
| radBridgeIPXSapInfEntry | 1.3.6.1.4.1.164.4.1.5.3.7.1 | ||
| Each entry corresponds to one ifindex. | |||
| OBJECT-TYPE | |||
| RadBridgeIPXSapInfEntry | |||
| radBridgeIPXSapInfIfIndex | 1.3.6.1.4.1.164.4.1.5.3.7.1.1 | ||
| This value of Ifindex is same as radBridgeIPXIfIndex in the IPX Interface Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapInfBcastUpdate | 1.3.6.1.4.1.164.4.1.5.3.7.1.2 | ||
| The SAP periodic update interval, in seconds. Zero value corresponds to infinite interval. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIPXSapInfAgeMultiplier | 1.3.6.1.4.1.164.4.1.5.3.7.1.3 | ||
| The holding multiplier for information received in SAP periodic updates. Zero value corresponds to infinite aging time. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| newMasking | 1.3.6.1.4.1.164.4.1.6 | ||
| OBJECT IDENTIFIER | |||
| maskingMaxEntries | 1.3.6.1.4.1.164.4.1.6.1 | ||
| The maximum number of entries in the masking table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingCurrentEntries | 1.3.6.1.4.1.164.4.1.6.2 | ||
| The number of entries in the mask table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingTable | 1.3.6.1.4.1.164.4.1.6.3 | ||
| This is the new masking scheme. Mask tables enable definition of forwarding restrictions and control of message flow in the internetwork. Each entry in this table defines a mask statement and an action defined by maskingOperation. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MaskingEntry | |||
| maskingEntry | 1.3.6.1.4.1.164.4.1.6.3.1 | ||
| Defines the contents of each line in the mask table. | |||
| OBJECT-TYPE | |||
| MaskingEntry | |||
| maskingType | 1.3.6.1.4.1.164.4.1.6.3.1.1 | ||
| Defines the type of mask entry. | |||
| OBJECT-TYPE | |||
| INTEGER | tx(1), rx(2), compress(3), priority(4), loadSharing(5), facs(6), codConnect(7), codDisconnect(8) | ||
| maskingIfIndex | 1.3.6.1.4.1.164.4.1.6.3.1.2 | ||
| Specifies the ifIndex of the interface to which the mask is applied. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingIndex | 1.3.6.1.4.1.164.4.1.6.3.1.3 | ||
| An index to the masking table. This number should not be greater than maskingMaxEntries | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingProtocolType | 1.3.6.1.4.1.164.4.1.6.3.1.4 | ||
| The base protocol for masking. IPX, IP, others. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ip(2), ipx(3), sna(4), netbios(5), apple(6), dec(7), all(255) | ||
| maskingSmartMaskOID | 1.3.6.1.4.1.164.4.1.6.3.1.5 | ||
| A reference to a specific Smart mask table (old radBridgeMaskTable) which enables a more specific mask type. If this information is not available, its value should be set to the OBJECT IDENTIFIER { 0 0 }. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| maskingFrameType | 1.3.6.1.4.1.164.4.1.6.3.1.6 | ||
| Enables the user to decide about frame type * all frame * just broadcast * just multicast. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), all(2), broadcast(3), multicast(4) | ||
| maskingFrameTypeCondition | 1.3.6.1.4.1.164.4.1.6.3.1.7 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingFrameType the packet contains data that matches the content of maskingFrameType. fa lse - Condition is valid if at the position specified by maskingFrameType the packet contains data that does not match the content of maskingFrameType. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingSourceAddress | 1.3.6.1.4.1.164.4.1.6.3.1.8 | ||
| The source address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). | |||
| OBJECT-TYPE | |||
| GenAddress | |||
| maskingSourceActiveBits | 1.3.6.1.4.1.164.4.1.6.3.1.9 | ||
| Specifies the positions of the wild card characters (*) in the maskingSourceAddress field. Only the 1's bit will be taken in considerations. | |||
| OBJECT-TYPE | |||
| GenAddress | |||
| maskingSourceMacOrNet | 1.3.6.1.4.1.164.4.1.6.3.1.10 | ||
| The variable maskingSourceAddress and maskingSourceActiveBits will be treated as MAC, or NET address. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingSourceMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingSourceMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingSourceMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingSourceMacOrNet can be either macAddress or appleAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | macAddress(1), netAddress(2), ipRange(3), appleAddress(4) | ||
| maskingSourceCondition | 1.3.6.1.4.1.164.4.1.6.3.1.11 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that matches the content of maskingSourceAddress. false - Condition is valid if at the position specified by maskingSourceAddress (in conjunction with maskingSourceActiveBits) the packet contains data that does not match the content of maskingSourceAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingDestAddress | 1.3.6.1.4.1.164.4.1.6.3.1.12 | ||
| If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. The destination address is according to the maskingMacOrNet and maskingProtocolType variables. In case of 'MAC' enter 6 bytes (48 bit) of source address. In case of 'NET' if the maskingProtocolType is IP, this is the IP address if the maskingProtocolType is IPX, this is the IPX address (nnnnmmmmmmss) nnnn - IPX net address mmmmmm - Node address (Mac) ss - IPX socket. In case of 'Apple' nn - net address (4 nibbles) ss - socket (4 nibbles). The IPX socket entered here has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care. | |||
| OBJECT-TYPE | |||
| GenAddress | |||
| maskingDestActiveBits | 1.3.6.1.4.1.164.4.1.6.3.1.13 | ||
| If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the positions of the wild card characters (*) in the maskingDestAddress field. Only the 1's bit will be taken in considerations. | |||
| OBJECT-TYPE | |||
| GenAddress | |||
| maskingDestMacOrNet | 1.3.6.1.4.1.164.4.1.6.3.1.14 | ||
| If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. - If maskingProtocolType = 'all', 'sna', 'netbios', dec or 'unknown', the maskingDestMacOrNet can be macAddress only! - If maskingProtocolType = 'ip' the maskingDestMacOrNet can be macAddress or netAddress or appleAddress. - If maskingProtocolType = 'ipx', the maskingDestMacOrNet can be either macAddress or netAddress. - If maskingProtocolType = 'apple', the maskingDestMacOrNet can be either macAddress or appleAddress. The variable maskingDestAddress and maskingDestActiveBits will be treated as MAC, or NET address. | |||
| OBJECT-TYPE | |||
| INTEGER | macAddress(1), netAddress(2), ipRange(3), appleAddress(4) | ||
| maskingDestCondition | 1.3.6.1.4.1.164.4.1.6.3.1.15 | ||
| If maskingFrameType = broadcast or multicast, this object is NOT APPLICABLE. If maskingFrameType = all or unknown, this object is applicable. Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that matches the content of maskingDestAddress. false - Condition is valid if at the position specified by maskingDestAddress (in conjunction with maskingDestActiveBits) the packet contains data that does not match the content of maskingDestAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingLowLevelProt | 1.3.6.1.4.1.164.4.1.6.3.1.16 | ||
| This field is set in conjunction with the maskingProtocolType variable. This variable specifies the low level protocol. The IPX socket entered in maskingDestAddress has priority over the value of maskingLowLevelProt, when it is ipxRip, ipxSap or ipxSpx, unless the entered IPX socket is don't care. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ipxRip(2), ipxSap(3), ipxSpx(4), ipUdp(5), ipTcp(6), ipIcmp(7), ipxNcp(8), ipxWan(9), ipxEco(10), ipxErr(11), ipxPep(12) | ||
| maskingLowLevelProtCondition | 1.3.6.1.4.1.164.4.1.6.3.1.17 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that matches the content of maskingLowLevelProt. false - Condition is valid if at the position specified by maskingLowLevelProt the packet contains data that does not match the content of maskingLowLevelProt. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingHighLevelProt | 1.3.6.1.4.1.164.4.1.6.3.1.18 | ||
| This field is set in connection to the maskingProtocolType variable. This variable specifies the high level protocols (application). As for today it supports just IP protocol stack. The object's value is a sum of the following instances values (selected by user): none (0), -- don't care ftp (1), ftpC (2), telnet (4), smtp (8), tftp (16), snmp (32), snmpTrap (64), ipRip (128), www (256), email (512), dns (1024), For Apple Protocol only: rtmp (2048), nbp (4096), atp (8192), aep (16384), zip (32768), adsp (65536), pap (131072), asp (262144) Example: if ftp(1), snmp(32) and snmpTrap(64) instances were selected, the value should be 97 (=1+32+64). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingHighLevelProtCondition | 1.3.6.1.4.1.164.4.1.6.3.1.19 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that matches the content of maskingHighLevelProt. false - Condition is valid if at the position specified by maskingHighLevelProt the packet contains data that does not match the content of maskingHighLevelProt. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingPortNum | 1.3.6.1.4.1.164.4.1.6.3.1.20 | ||
| The port number is the same as in high level protocol. It specifies the dest. port in IP case or the dest. socket in case of IPX & apple protocols. IP - This object is applicable only if none (0) value was selected in maskingHighLevelProt. IPX - This object is applicable only if the socket entered in maskingDestAddress is 'don't care'(00) AND maskingLowLevelProt is NOT ipxRip or ipxSap. Apple - This option is applicable only if the socket entered in maskingDestAddress is 'don't care'(00). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingPortNumCondition | 1.3.6.1.4.1.164.4.1.6.3.1.21 | ||
| Specifies the logical condition of the mask pattern: true - Condition is valid if at the position specified by maskingPortNum the packet contains data that matches the content of maskingPortNum. false - Condition is valid if at the position specified by maskingPortNum the packet contains data that does not match the content of maskingPortNum. This object is applicable only when maskingPortNum is applicable. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| maskingOperation | 1.3.6.1.4.1.164.4.1.6.3.1.22 | ||
| The type of action to be taken if the frame meets the conditions of the mask. noOp = disabled (mask remains on list, but is not active) delete = mask is removed from the list. smartMask = the operation and destination of the mask will be determined by the objects of the Smart Table (old masking table: radBridgeMaskTable). If maskingType is codConnect, the 'block' value is NOT allowed. If maskingType is codDisconnect, the 'forward' value is NOT allowed. | |||
| OBJECT-TYPE | |||
| INTEGER | block(1), forward(2), route(3), forward-route(4), high-priority(5), noOp(6), delete(7), smartMask(8) | ||
| maskingSrcPortNum | 1.3.6.1.4.1.164.4.1.6.3.1.23 | ||
| The source port number. For IP: No Condition. For IPX: This object is applicable only if the socket entered in maskingSourceAddress is don't care (00) and maskingLowLevelProt is NOT ipxRip or ipxSap. For Apple:This object is applicable only if the socket entered in maskingSourceAddress is don't care (00). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| maskingSrcPortNumCondition | 1.3.6.1.4.1.164.4.1.6.3.1.24 | ||
| The same as 'maskingPortNumCondition'. Relates to source port. | |||
| OBJECT-TYPE | |||
| INTEGER | false(1), true(2) | ||
| radBridgePerformance | 1.3.6.1.4.1.164.4.1.7 | ||
| OBJECT IDENTIFIER | |||
| radBridgeCurrentTable | 1.3.6.1.4.1.164.4.1.7.1 | ||
| The RAD Bridge Current table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeCurrentEntry | |||
| radBridgeCurrentEntry | 1.3.6.1.4.1.164.4.1.7.1.1 | ||
| An entry in the RAD Bridge Current table. | |||
| OBJECT-TYPE | |||
| RadBridgeCurrentEntry | |||
| radBridgeCurrentIndex | 1.3.6.1.4.1.164.4.1.7.1.1.1 | ||
| The index of the Bridge interface. It may be ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeCurrentIngressFilteringDiscardedFrames | 1.3.6.1.4.1.164.4.1.7.1.1.2 | ||
| The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| radBridgeCurrentFrameTypeDiscardedFrames | 1.3.6.1.4.1.164.4.1.7.1.1.3 | ||
| The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| radBridgeIntervalTable | 1.3.6.1.4.1.164.4.1.7.2 | ||
| The RAD Bridge Interval table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| RadBridgeIntervalEntry | |||
| radBridgeIntervalEntry | 1.3.6.1.4.1.164.4.1.7.2.1 | ||
| An entry in the RAD Bridge Interval table. | |||
| OBJECT-TYPE | |||
| RadBridgeIntervalEntry | |||
| radBridgeIntervalIndex | 1.3.6.1.4.1.164.4.1.7.2.1.1 | ||
| The index of the bridge interface. It may be ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radBridgeIntervalNumber | 1.3.6.1.4.1.164.4.1.7.2.1.2 | ||
| A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals exist). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..96 | ||
| radBridgeIntervalIngressFilteringDiscardedFrames | 1.3.6.1.4.1.164.4.1.7.2.1.3 | ||
| The counter associated with the number of Discarded Frames upon Ingress Filtering, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| radBridgeIntervalFrameTypeDiscardedFrames | 1.3.6.1.4.1.164.4.1.7.2.1.4 | ||
| The counter associated with the number of Discarded Frames upon Frame Type and Tagging Mismatch, encountered by a Bridge interface in one of the previous 96, individual 15 minute, intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| lanranger | 1.3.6.1.4.1.164.4.2 | ||
| OBJECT IDENTIFIER | |||
| lanrangerEvents | 1.3.6.1.4.1.164.4.2.0 | ||
| The events for the LANRANger. | |||
| OBJECT-IDENTITY | |||
| lanrangerLogLinkUp | 1.3.6.1.4.1.164.4.2.0.1 | ||
| The lanrangerLogLinkUp trap indicates that the indicated logical link is connected. | |||
| NOTIFICATION-TYPE | |||
| lanrangerLinkConnPhysLink | |||
| lanrangerLinkConnAid | |||
| lanrangerLogLinkDown | 1.3.6.1.4.1.164.4.2.0.2 | ||
| The lanrangerLogLinkDown trap indicates that the indicated logical link is disconnected. | |||
| NOTIFICATION-TYPE | |||
| lanrangerLinkConnPhysLink | |||
| lanrangerLinkConnAid | |||
| lanrangerLanTableOverflow | 1.3.6.1.4.1.164.4.2.0.3 | ||
| The station table has the maximum number of addresses for the LANRANger. | |||
| NOTIFICATION-TYPE | |||
| lanrangerStatusChanged | 1.3.6.1.4.1.164.4.2.0.4 | ||
| The trap indicates changes in the device status . | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| lanrangerConfig | 1.3.6.1.4.1.164.4.2.1 | ||
| OBJECT IDENTIFIER | |||
| lanrangerLoc | 1.3.6.1.4.1.164.4.2.1.1 | ||
| lanrangerLoc is set to main if the LANRANger is located on the main LAN and it is set to remote if it is located on a LAN at a remote site. | |||
| OBJECT-TYPE | |||
| INTEGER | main(1), remote(2) | ||
| lanrangerBurnAddress | 1.3.6.1.4.1.164.4.2.1.2 | ||
| This is the burned-in MacAddress on the LANRANger. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerLocAddress | 1.3.6.1.4.1.164.4.2.1.3 | ||
| This is a locally administered address. If a zero value appears, the network administrator did not set a locally administered address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerActiveAddress | 1.3.6.1.4.1.164.4.2.1.4 | ||
| The MAC address that is in use on the LANRANger. The address selected will appear in ifPhysAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | burnedIn(1), locallyAdministered(2) | ||
| lanrangerLearningStationTopology | 1.3.6.1.4.1.164.4.2.1.5 | ||
| The Learning station topology defines for the LANRANger which type of station will be inserted in the station list. The default value is permanentAndDynamic(3). dynamic(1) - Learning lan station only. permanent(2) - permanentAndDynamic(3)- Setting this parameter will reset the LANRANger . ----- | |||
| OBJECT-TYPE | |||
| INTEGER | dynamic(1), permanent(2), permanentAndDynamic(3) | ||
| lanrangerIpRouterInfo | 1.3.6.1.4.1.164.4.2.1.6 | ||
| OBJECT IDENTIFIER | |||
| lanrangerIpDefaultLink | 1.3.6.1.4.1.164.4.2.1.6.1 | ||
| The default selected link, having the numbering system of ifIndex. The valid values range is: 1..ifIndex. The value must remain constant at least from one re-initialization of the network management agent to the next. notSupported = 255 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerIpFastReTxLevel | 1.3.6.1.4.1.164.4.2.1.6.2 | ||
| The maximum buffer depth (queue length) for which lanranger will accept retransmission (for each station; the level is the same for all the stations). The valid values range is: 1..255 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerIpAgingTimeout | 1.3.6.1.4.1.164.4.2.1.6.3 | ||
| Ip aging time for a station - in min. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerIpBootP | 1.3.6.1.4.1.164.4.2.1.6.4 | ||
| OBJECT IDENTIFIER | |||
| lanrangerBootPAction | 1.3.6.1.4.1.164.4.2.1.6.4.1 | ||
| Activating (disable/enable) the BootP operation. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| lanrangerBootPAvailableEntries | 1.3.6.1.4.1.164.4.2.1.6.4.2 | ||
| The number of available entries in the BootP table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerBootPCurrentEntries | 1.3.6.1.4.1.164.4.2.1.6.4.3 | ||
| The current number of BootP entries in the BootP table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerBootPTable | 1.3.6.1.4.1.164.4.2.1.6.4.4 | ||
| A list of BootP entries. The number of entries is up to BootP current entries, according to the LANRANger model. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerBootPEntry | |||
| lanrangerBootPEntry | 1.3.6.1.4.1.164.4.2.1.6.4.4.1 | ||
| BootP parameters per entry of the BootP table. | |||
| OBJECT-TYPE | |||
| LanrangerBootPEntry | |||
| lanrangerBootPIpAddress | 1.3.6.1.4.1.164.4.2.1.6.4.4.1.1 | ||
| BootP Ip Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| lanrangerBootPIfIndex | 1.3.6.1.4.1.164.4.2.1.6.4.4.1.2 | ||
| The number is the same as the ifIndex of the link. | |||
| OBJECT-TYPE | |||
| INTEGER | notAllocated(255) | ||
| lanrangerBootPOperation | 1.3.6.1.4.1.164.4.2.1.6.4.4.1.3 | ||
| This object indicates the status of this entry. active(1) - this entry is currently in use and will remain so even after the next reset of the LANRANger. delete(2) - writing this value to the object, removes the corresponding entry from the table. | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), delete(2) | ||
| lanrangerSpoofingInfo | 1.3.6.1.4.1.164.4.2.1.7 | ||
| OBJECT IDENTIFIER | |||
| lanrangerSpoofingAction | 1.3.6.1.4.1.164.4.2.1.7.1 | ||
| Spoofing action is applied by bit code: enable : bit 0 set (disable: bit 0 is 0) keepAlive : bit 1 ... : bit 2 and so on. For the above example, to set spoofing to keepAlive action, the object's value will be 3 = [ 2**0 + 2**1 ] Only the Remote LANRANger will accept this object ! ------- | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingAgingStation | 1.3.6.1.4.1.164.4.2.1.7.2 | ||
| Aging time of stations list, in min. The agent 'translates' the time entered in minutes, to 10 min. resolution, as follows: 1..10 min - 10 min 11..20 min - 20 min and so on... 0 is not a valid value. Only the Remote LANRANger will accept this object ! ---------------- | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerInterface | 1.3.6.1.4.1.164.4.2.2 | ||
| OBJECT IDENTIFIER | |||
| lanrangerLinkTable | 1.3.6.1.4.1.164.4.2.2.1 | ||
| A list of link entries. The number of entries is up to 8, according to the LANRANger model. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerLinkEntry | |||
| lanrangerLinkEntry | 1.3.6.1.4.1.164.4.2.2.1.1 | ||
| LANRANger-specific parameter values for a link. | |||
| OBJECT-TYPE | |||
| LanrangerLinkEntry | |||
| lanrangerLinkIndex | 1.3.6.1.4.1.164.4.2.2.1.1.1 | ||
| A unique value for each link, equal to the value of ifIndex. The value for each link must remain constant at least from one re-initialization of the network management agent to the next. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkType | 1.3.6.1.4.1.164.4.2.2.1.1.2 | ||
| The link type . | |||
| OBJECT-TYPE | |||
| INTEGER | synchronous(1), asynchronous(2), x25FRconfig(3), x25FRchannel(4), isdn(5), frameRelay(6), pcmcia(7), dm2wire(8), notExist(254), unknown(255) | ||
| lanrangerLinkState | 1.3.6.1.4.1.164.4.2.2.1.1.3 | ||
| The link is disabled, enabled or backup. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3), backup(4) | ||
| lanrangerLinkDTRMode | 1.3.6.1.4.1.164.4.2.2.1.1.4 | ||
| The link DTR mode. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), unknown(255) | ||
| lanrangerLinkStatus | 1.3.6.1.4.1.164.4.2.2.1.1.5 | ||
| The link physical status . | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), fail(2), rxNoClock(3), txProblem(4), noCarrierD(5), unknown(255) | ||
| lanrangerLinkConnectionStatus | 1.3.6.1.4.1.164.4.2.2.1.1.6 | ||
| The link connection status. | |||
| OBJECT-TYPE | |||
| INTEGER | fail(1), disconnect(2), connect(3), wait(4), down(5), trying(6), testing(7), unknown(255) | ||
| lanrangerLinkNumOfLogLinks | 1.3.6.1.4.1.164.4.2.2.1.1.7 | ||
| The number of logical links on this physical link. 0 = noLogicalLink | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkReset | 1.3.6.1.4.1.164.4.2.2.1.1.8 | ||
| Setting this attribute to ON will reset the link . Upon completion the value will be set to OFF | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| lanrangerLinkRxMaskedFrames | 1.3.6.1.4.1.164.4.2.2.1.1.9 | ||
| The number of masked frames received on this physical link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| lanrangerLinkLayer2Type | 1.3.6.1.4.1.164.4.2.2.1.1.10 | ||
| The link layer 2 type indicates whether the link is Bridge or Router and specifies the Router's type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), bridge(2), ipRouter(3), ipxRouter(4), ipAndIpxRouter(5), bRouter(6), ipBrouter(7), ipxBrouter(8), ipAndIpxBrouter(9), bridgeAndStp(10) | ||
| lanrangerLinkLayer3Type | 1.3.6.1.4.1.164.4.2.2.1.1.11 | ||
| The link layer 3 type indicates the protocol type. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), proprietary(2), terminalServer(3), slip(30), cSlip(31), ppp(40), rfc1490(41), hdlcFraming(42), mlPpp(43) | ||
| lanrangerBackupLink | 1.3.6.1.4.1.164.4.2.2.1.1.12 | ||
| The backup link interface index located in the two LSB bytes. If the link is FR type, the two MSB will contain a DLCi number. For other link types the two MSB will equal to 0. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| wrWanThrottle | 1.3.6.1.4.1.164.4.2.2.1.1.13 | ||
| Throttle controls the baud rate of the WAN. For example if we have a WAN rate of 2M but we want only 1/2 M as the baud rate we set the Wan Throttle to 512k. These are the values: Full (2), 1M (3), 512k (4), 128k (5), 64k (6) Full throttle option (2) means the LAN rate. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkConnection | 1.3.6.1.4.1.164.4.2.2.2 | ||
| OBJECT IDENTIFIER | |||
| lanrangerConnMaxEntries | 1.3.6.1.4.1.164.4.2.2.2.1 | ||
| The maximum number of entries in the Connection table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerConnCurrentEntries | 1.3.6.1.4.1.164.4.2.2.2.2 | ||
| The current number of entries in the Connection table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkConnTable | 1.3.6.1.4.1.164.4.2.2.2.3 | ||
| A list of Connection entries. The number of entries is up to Max entries, according to the LANRANger model. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerLinkConnEntry | |||
| lanrangerLinkConnEntry | 1.3.6.1.4.1.164.4.2.2.2.3.1 | ||
| Information about LANRANger Connection. | |||
| OBJECT-TYPE | |||
| LanrangerLinkConnEntry | |||
| lanrangerLinkConnPhysLink | 1.3.6.1.4.1.164.4.2.2.2.3.1.1 | ||
| The lanrangerLinkIndex for the physical link with which this logical link is associated. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkConnAid | 1.3.6.1.4.1.164.4.2.2.2.3.1.2 | ||
| A unique value for each logical link. The maximum number of logical links is 256, according to the LANRANger model. The value for each logical link must remain constant at least from one re-initialization of the network management agent to the next. This index is the SPS address of the logical link. noLogicLink = 65535 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkConnMacAddr | 1.3.6.1.4.1.164.4.2.2.2.3.1.3 | ||
| The MAC address of the device that the logical link is connected to on the remote LAN. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerLinkConnStatus | 1.3.6.1.4.1.164.4.2.2.2.3.1.4 | ||
| The link connection status. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), none(2), fail(3), connect(4), wait(5), down(6) | ||
| lanrangerLinkConnDeviceType | 1.3.6.1.4.1.164.4.2.2.2.3.1.5 | ||
| The type of device that the logical link is connected to on the remote LAN. | |||
| OBJECT-TYPE | |||
| INTEGER | tre1(1), tre8(2), tre1D(3), tre8D(4), tre8M(5), rrTre(6), rrTre1D(7), rrTre8D(8), iTre1(9), iTre2(10), mpTre8(11), kTre8(12), treRasA(13), treRasS(14), trePCAsync(15), trePCSync(16), mbe1(17), mbe8(18), mbe1D(19), mbe8D(20), ete8M(21), iEre1(22), iEe2(23), mpMbe8(24), kMbe8(25), mbePCAsync(26), mbePCSync(27), mbeRasA(28), mbeRasS(29), other(255) | ||
| lanrangerLinkConnDeviceName | 1.3.6.1.4.1.164.4.2.2.2.3.1.6 | ||
| The logical name of the device that the logical link is connected to on the remote LAN. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| lanrangerLinkConnDeviceSWVer | 1.3.6.1.4.1.164.4.2.2.2.3.1.7 | ||
| SW Version of the device that the logical link is connected to, on the remote LAN. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| lanrangerLinkConnNumLanStation | 1.3.6.1.4.1.164.4.2.2.2.3.1.8 | ||
| The number of stations of the remote LAN. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkSyncStatus | 1.3.6.1.4.1.164.4.2.2.2.3.1.9 | ||
| The Sync link status. | |||
| OBJECT-TYPE | |||
| INTEGER | synchronized(1), syncNotObtained(2), waitForSync(3), codDisconnected(4), lcp(5), ip(6), ipvj(7), ipx(8), ipIpx(9), ipvj-ipx(10), mlPpp(11), mlPpp-ip(12), mlPpp-ip-ipvj(13), mlPpp-ip-ipx(14), mlPpp-ipvj-ipx(15), mlPpp-ipx(16), frUp(17), frDown(18), dlciUp(19), dlciDown(20), extLoop(21), ipcp(22), lcpIpcp(23), redAlarm(24), yellowAlarm(26), localSyncLoss(27), remoteSyncLoss(28), networkLoop(29), networkLoopRedAlarm(30), networkLoopYelAlarm(31), networkLocSyncLoss(32), networkRemSyncLoss(33), fdlLoop(34), fdlLoopRedAlarm(35), fdlLoopYellowAlarm(36), fdlLoopLocSyncLoss(37), fdlLoopRemSyncLoss(38), loopback(39), loopbackLocSyncLoss(40), loopbackRemSyncLoss(41) | ||
| lanrangerModemTable | 1.3.6.1.4.1.164.4.2.2.3 | ||
| A list of Modem entries. The number of entries is up to ifIndex. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerModemEntry | |||
| lanrangerModemEntry | 1.3.6.1.4.1.164.4.2.2.3.1 | ||
| LANRANger-specific parameter values for a Modem. | |||
| OBJECT-TYPE | |||
| LanrangerModemEntry | |||
| lanrangerModemLinkIndex | 1.3.6.1.4.1.164.4.2.2.3.1.1 | ||
| A list of asynchronous ports of the link, according to ifIndex. Synchronous ports will not appear in this table. Their port number will be skipped. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerModemName | 1.3.6.1.4.1.164.4.2.2.3.1.2 | ||
| The Modem Name identifier for MBE/TRE. Up to 50 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| lanrangerModemSettingString | 1.3.6.1.4.1.164.4.2.2.3.1.3 | ||
| Modem setting String. Up to 80 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| lanrangerModemAutobaudingSpeed | 1.3.6.1.4.1.164.4.2.2.3.1.4 | ||
| Enable or disable autobauding. When the Autobauding feature is enabled, the MBE/TRE automatically ranges over various Baud rates, starting with 115.2 Kbps, until the correct Baud rate of the modem is detected. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| lanrangerModemResetBeforeSetup | 1.3.6.1.4.1.164.4.2.2.3.1.5 | ||
| Reset the modem before setup is performed. It is recommended to reset the modem before modem setup session. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| lanrangerModemAnalyzeAnswers | 1.3.6.1.4.1.164.4.2.2.3.1.6 | ||
| Enable this option if a modem using non-standard answering is used. When this mode is enabled, the MBE/TRE awaits modem answers 'CONNECT', 'CARRIER', or 'OK', after it transmits a modem command. Modem answers acknowledge, that a specific command has been executed. If this option is not enabled, the MBE/TRE waits for a modem answer for three seconds. If no answer has been received during this period, the MBE/TRE continues functioning as if the modem command was successfully executed. However, when dialing out, the MBE/TRE waits for one minute for connection. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| lanrangerModemSpeaker | 1.3.6.1.4.1.164.4.2.2.3.1.7 | ||
| Toggle the Modem Speaker On or Off . | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| lanrangerModemDialingNumber | 1.3.6.1.4.1.164.4.2.2.3.1.8 | ||
| Various command switches listed in Modem Dialing Number Menu allows selection of tone, pulse-dialing, or various wait states. P - Set Pulse dialing number . T - Set Tone dialing number . W - Wait for dialing tone before proceeding. ' - Pause for 2 seconds . @ - Wait for silence, one ring, followed by 5 sec. of silence . The Dialing Number will include both digits and letter/s of the command switches. The order and validity will be on user's responsibility. The DisplayString can have up to 40 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| wrLocalDialBackNumber | 1.3.6.1.4.1.164.4.2.2.3.1.9 | ||
| This is the number that the Remote Modem will use to call the local Modem at Dial Back. Various command switches listed in Modem Dialing Number Menu allows selection of tone, pulse-dialing, or various wait states. P - Set Pulse dialing number . T - Set Tone dialing number . W - Wait for dialing tone before proceeding. ' - Pause for 2 seconds . @ - Wait for silence, one ring, followed by 5 sec. of silence . The Dialing Number will include both digits and letter/s of the command switches. The order and validity will be on user's responsibility. The DisplayString can have up to 40 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| wrRingsBeforeAnswer | 1.3.6.1.4.1.164.4.2.2.3.1.10 | ||
| Determines which ring the modem will wait to answer the phone on. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerModemDialRetries | 1.3.6.1.4.1.164.4.2.2.3.1.11 | ||
| The number of dialing retries requested. Default = 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8 | ||
| lanrangerLinkPktSwTable | 1.3.6.1.4.1.164.4.2.2.4 | ||
| A list of X.25/FR modules entries. The number of entries is up to ifIndex. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerLinkPktSwEntry | |||
| lanrangerLinkPktSwEntry | 1.3.6.1.4.1.164.4.2.2.4.1 | ||
| LANRANger-specific parameter values for X.25/FR modules. | |||
| OBJECT-TYPE | |||
| LanrangerLinkPktSwEntry | |||
| lanrangerLinkPktSwIndex | 1.3.6.1.4.1.164.4.2.2.4.1.1 | ||
| A unique value for each X.25/FR of the link, according to numbering system of ifIndex. The maximum number of links is ifIndex. The value for each link must remain constant at least from one re-initialization of the network management agent to the next. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkPktSwType | 1.3.6.1.4.1.164.4.2.2.4.1.2 | ||
| Packet Switch Type. | |||
| OBJECT-TYPE | |||
| INTEGER | x25FRChannel(1), x25FRConfig(2) | ||
| lanrangerLinkPktSwControlSignal | 1.3.6.1.4.1.164.4.2.2.4.1.3 | ||
| Packet Switch control command. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| lanrangerLinkPktSwSpeed | 1.3.6.1.4.1.164.4.2.2.4.1.4 | ||
| The Pkt Switch port's speed in bits per second. Range: 1200bps .. 1544000bps | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLinkPktSwConfigParity | 1.3.6.1.4.1.164.4.2.2.4.1.5 | ||
| The Pkt Switch Config port's character parity bit. Applicable only for x25FRConfigChannel. For x25FRChannel the value notApplicable applies. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), odd(2), even(3), notApplicable(255) | ||
| lanrangerLinkPktSwConfigStopBit | 1.3.6.1.4.1.164.4.2.2.4.1.6 | ||
| The Pkt Switch Config port's number of stop bits. Applicable only for x25FRConfigChannel. For x25FRChannel the value notApplicable applies. | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), notApplicable(255) | ||
| lanrangerLinkPktSwResetModule | 1.3.6.1.4.1.164.4.2.2.4.1.7 | ||
| Reset command to Pkt Switch module. Applicable only for x25FRChannel. The command will have no effect on x25FRConfigChannel. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| wrPPPTable | 1.3.6.1.4.1.164.4.2.2.5 | ||
| This table contains only parameters that do not exist in the PPP standard MIBS. The table contains a list of PPP entries. The number of entries is up to ifIndex. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| WrPPPEntry | |||
| wrPPPEntry | 1.3.6.1.4.1.164.4.2.2.5.1 | ||
| LANRANger-specific parameter values for a PPP. | |||
| OBJECT-TYPE | |||
| WrPPPEntry | |||
| wrPPPCompressionHeaderField | 1.3.6.1.4.1.164.4.2.2.5.1.1 | ||
| This configuration option provides a method to negotiate the compression of the Data Link Layer Address and Control fields. This configuration option is sent to inform the peer that the implementation can receive compressed Address and Control fields. | |||
| OBJECT-TYPE | |||
| INTEGER | compressionOff(2), compressionOn(3) | ||
| wrPPPCompressionProtocolFields | 1.3.6.1.4.1.164.4.2.2.5.1.2 | ||
| This configuration option provides a method to negotiate the compression of the PPP Protocol field. This configuration option is sent to inform the peer that the implementation can receive such single octet Protocol fields. | |||
| OBJECT-TYPE | |||
| INTEGER | compressionOff(2), compressionOn(3) | ||
| wrPPPSTACCompressionType | 1.3.6.1.4.1.164.4.2.2.5.1.3 | ||
| The PPP compression control protocol provides a method to negotiate and utilize compression protocol over PPP encapsulated links. These are Different types of data compression algorithm for PPP encapsulated packets. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), noHistory(2), lCB(3), sequence(4), extended(5) | ||
| wrPPPAuthProtocol | 1.3.6.1.4.1.164.4.2.2.5.1.4 | ||
| The type of authentication protocol being used. The left parameter is the maximum authentication, the right parameter is minimum authentication. | |||
| OBJECT-TYPE | |||
| INTEGER | noneNone(1), chapNone(2), chapPap(3), chapChap(4), papNone(5), papPap(6) | ||
| wrPPPSecurityType | 1.3.6.1.4.1.164.4.2.2.5.1.5 | ||
| Type of unit. | |||
| OBJECT-TYPE | |||
| INTEGER | host(1), guest(2) | ||
| wrPPPUserName | 1.3.6.1.4.1.164.4.2.2.5.1.6 | ||
| PPP User name. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(0..10) | ||
| wrPPPPassword | 1.3.6.1.4.1.164.4.2.2.5.1.7 | ||
| PPP Password . | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(0..10) | ||
| wrPPPLinkActiveTime | 1.3.6.1.4.1.164.4.2.2.5.1.8 | ||
| PPP link active time in seconds Values range: 2 - 900. Default value = 2 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerStation | 1.3.6.1.4.1.164.4.2.3 | ||
| OBJECT IDENTIFIER | |||
| lanrangerStationTable | 1.3.6.1.4.1.164.4.2.3.1 | ||
| A table that contains information about the stations on the remote LAN(s). A remote LANRANger contains a list of stations on its LAN, while a main LANRANger contains a list of stations at all the remote sites it is connected to. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerStationEntry | |||
| lanrangerStationEntry | 1.3.6.1.4.1.164.4.2.3.1.1 | ||
| Information about a specific station, that the LANRANger lists as being on a remote LAN. | |||
| OBJECT-TYPE | |||
| LanrangerStationEntry | |||
| lanrangerStationPhysLink | 1.3.6.1.4.1.164.4.2.3.1.1.1 | ||
| The number of the physical link that is connected to the remote LAN on which the station with the associated instance of lanrangerStationAddress is located. The number is the same as the ifIndex of the link. The value will be zero on a remote LANRANger | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerStationLogLink | 1.3.6.1.4.1.164.4.2.3.1.1.2 | ||
| The number of the logical link that is connected to the remote LAN on which the station with the associated instance of lanrangerStationAddress is located. The value will be zero on a remote LANRANger. noLogicLink = 65535 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerStationAddress | 1.3.6.1.4.1.164.4.2.3.1.1.3 | ||
| The unicast MAC address of a station that the LANRANger lists as being on a remote LAN. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerStationStatus | 1.3.6.1.4.1.164.4.2.3.1.1.4 | ||
| The status of this entry. The meanings of the values are: unknown(1) : learned(2) : the value of the corresponding instance of lanrangerStationAddress was learned and is being used. self(3) : the value of the corresponding instance of lanrangerStationAddress represents the LANRANger's address. static(4) : the value of the corresponding instance of lanrangerStationAddress is also the value of an existing instance of lanrangerStaticAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), learned(2), self(3), static(4) | ||
| lanrangerStationSpoofingStatus | 1.3.6.1.4.1.164.4.2.3.1.1.5 | ||
| The spoofing status of this entry. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| lanrangerLanMaxStations | 1.3.6.1.4.1.164.4.2.3.2 | ||
| The maximum number of stations in the station table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerLanCurrentStations | 1.3.6.1.4.1.164.4.2.3.3 | ||
| The current number of stations in the station table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerPermanentStation | 1.3.6.1.4.1.164.4.2.3.4 | ||
| OBJECT IDENTIFIER | |||
| lanrangerPermanentMaxEntries | 1.3.6.1.4.1.164.4.2.3.4.1 | ||
| The maximum number of entries in the permanent stations table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerPermanentCurrentEntries | 1.3.6.1.4.1.164.4.2.3.4.2 | ||
| The current number of entries in the permanent stations table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerPermanentTable | 1.3.6.1.4.1.164.4.2.3.4.3 | ||
| A table containing address information configured into the LANRANger by (local or network) management, specifying addresses on a remote LAN. This table objects can be set only on a Remote LANRANger. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerPermanentEntry | |||
| lanrangerPermanentEntry | 1.3.6.1.4.1.164.4.2.3.4.3.1 | ||
| Address information configured into the remote LANRANger by (local or network) management specifying addresses on a remote LAN. | |||
| OBJECT-TYPE | |||
| LanrangerPermanentEntry | |||
| lanrangerPermanentIfIndex | 1.3.6.1.4.1.164.4.2.3.4.3.1.1 | ||
| The number of the physical link that is connected to the remote LAN, on which the station with the associated instance of lanrangerStationAddress is located. The number is the same as the ifIndex of the link. This data is interesting for main LANRANger only. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerPermanentLogLink | 1.3.6.1.4.1.164.4.2.3.4.3.1.2 | ||
| The number of the logical link that is connected to the remote LAN, on which the station with the associated instance of lanrangerPermanentAddress is located. The value will be noLogicLink on a remote LANRANger. This data is interesting for main LANRANger only. noLogicLink = 65535 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerPermanentAddress | 1.3.6.1.4.1.164.4.2.3.4.3.1.3 | ||
| The MAC address entered by management to this entry. Only the remote LANRANger will accept Set for this object ! ---------------- | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerPermanentOperation | 1.3.6.1.4.1.164.4.2.3.4.3.1.4 | ||
| This object indicates the status of this entry. active(1) - this entry is currently in use and will remain so even after the next reset of the LANRANger. delete(2) - writing this value to the object removes the corresponding entry. Only the remote LANRANger will accept Set for this object ! ---------------- | |||
| OBJECT-TYPE | |||
| INTEGER | active(1), delete(2) | ||
| lanrangerIpStation | 1.3.6.1.4.1.164.4.2.3.5 | ||
| OBJECT IDENTIFIER | |||
| lanrangerIpPermanentAvailableEntries | 1.3.6.1.4.1.164.4.2.3.5.1 | ||
| The available number of entries in the IP permanent stations table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerIpPermanentCurrentEntries | 1.3.6.1.4.1.164.4.2.3.5.2 | ||
| The current number of entries in the IP permanent station table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingStation | 1.3.6.1.4.1.164.4.2.3.6 | ||
| OBJECT IDENTIFIER | |||
| lanrangerSpoofingMaxEntries | 1.3.6.1.4.1.164.4.2.3.6.1 | ||
| The maximum number of entries in the Spoofing station table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingCurrentEntries | 1.3.6.1.4.1.164.4.2.3.6.2 | ||
| The current number of entries in the Spoofing station table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingTable | 1.3.6.1.4.1.164.4.2.3.6.3 | ||
| A list of Spoofing entries. The number of entries is up to the current number of entries, according to the LANRANger model. Only the LOCAL LANRANger will show this table ! --------------- | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| LanrangerSpoofingEntry | |||
| lanrangerSpoofingEntry | 1.3.6.1.4.1.164.4.2.3.6.3.1 | ||
| Spoofing parameters per entry of the Spoofing table. | |||
| OBJECT-TYPE | |||
| LanrangerSpoofingEntry | |||
| lanrangerSpoofingGroup | 1.3.6.1.4.1.164.4.2.3.6.3.1.1 | ||
| The spoofing group. Only the LOCAL Lanranger will show this table ! | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingMacAddress | 1.3.6.1.4.1.164.4.2.3.6.3.1.2 | ||
| MAC Address of the Remote Lanrangers. Only the LOCAL Lanranger will show this table ! | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| lanrangerSpoofingAging | 1.3.6.1.4.1.164.4.2.3.6.3.1.3 | ||
| Aging time defined for a whole group, in minutes. Only the LOCAL Lanranger will show this table ! | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| lanrangerSpoofingTimeLeft | 1.3.6.1.4.1.164.4.2.3.6.3.1.4 | ||
| Time until aging expires, per station, in minutes. Only the LOCAL Lanranger will show this table ! | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trim | 1.3.6.1.4.1.164.4.3 | ||
| OBJECT IDENTIFIER | |||
| trimInterface | 1.3.6.1.4.1.164.4.3.1 | ||
| OBJECT IDENTIFIER | |||
| trimIfTable | 1.3.6.1.4.1.164.4.3.1.1 | ||
| RAD-specific interface table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrimIfEntry | |||
| trimIfEntry | 1.3.6.1.4.1.164.4.3.1.1.1 | ||
| An entry in table trimIfTable. | |||
| OBJECT-TYPE | |||
| TrimIfEntry | |||
| trimIfIndex | 1.3.6.1.4.1.164.4.3.1.1.1.1 | ||
| Index to the Trimbridge Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIB II). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfBoardNum | 1.3.6.1.4.1.164.4.3.1.1.1.2 | ||
| Reserved for possible future use. Not currently applicable to Trimbridge. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfNetAddress | 1.3.6.1.4.1.164.4.3.1.1.1.3 | ||
| The IP address of the interface defined by the particular value of trimIfIndex. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| trimIfStatus | 1.3.6.1.4.1.164.4.3.1.1.1.4 | ||
| The current status of the interface. Some of these status values are not applicable to Trimbridge. | |||
| OBJECT-TYPE | |||
| INTEGER | ok(1), okSingleBrg(2), okMultiBrg(3), connctFault(4), rxFault(5), txFault(6), channelLoopback(7), rxClockFault(8), t1Alarm(9) | ||
| trimIfClockType | 1.3.6.1.4.1.164.4.3.1.1.1.5 | ||
| trimIfClockType defines the type of clock each interface uses: internal or external. | |||
| OBJECT-TYPE | |||
| INTEGER | external(1), internal(2), t1(3), g703(4) | ||
| trimIfBaudRate | 1.3.6.1.4.1.164.4.3.1.1.1.6 | ||
| Defines the baud rate in use by the interface. The valid rates are determined by the type of the media for which this baud rate is defined. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfCost | 1.3.6.1.4.1.164.4.3.1.1.1.7 | ||
| This object is inapplicable to Trimbridge. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfCompression | 1.3.6.1.4.1.164.4.3.1.1.1.8 | ||
| Defines whether data compression is enabled or disabled for the interface. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimIfCompressionStatus | 1.3.6.1.4.1.164.4.3.1.1.1.9 | ||
| Defines the status of the compression component: not-inserted - compression component is not in the device active - compression is enabled and operates correctly not-active - compression is enables but does not operate. The reason may be that there is no compression component on the device connected to this interface. disabled - compression was disabled by management, using variable trimCompression. | |||
| OBJECT-TYPE | |||
| INTEGER | not-inserted(1), active(2), not-active(3), disable(4) | ||
| trimIfCompressionRate | 1.3.6.1.4.1.164.4.3.1.1.1.10 | ||
| Percentage of compression. This variable applies only if trimCompressionStatus is active. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfLATCompression | 1.3.6.1.4.1.164.4.3.1.1.1.11 | ||
| Enable/Disable the LAT Compression. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimIfCompressionType | 1.3.6.1.4.1.164.4.3.1.1.1.12 | ||
| This parameter indicates the type of compression option available in the device. `None(1) - indicates that there is no compression option in the device lowSpeed(2) - indicates a compression option which is operational up to line speed sof 64 kbps. highSpeed(3) - indicates a compression option which is operational up to line speeds of 2 Mbps. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), lowSpeed(2), highSpeed(3) | ||
| trimIfFilterMode | 1.3.6.1.4.1.164.4.3.1.1.1.13 | ||
| This parameter indicates the type of filtering in the device. | |||
| OBJECT-TYPE | |||
| INTEGER | destinationOnly(1), sourceAndDestination(2) | ||
| trimIfConType | 1.3.6.1.4.1.164.4.3.1.1.1.14 | ||
| This parameter indicates the connector type of an interface. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), none(2), x21Old(3), x21(4), v35Old(5), v35(6), rs530Old(7), rs530(8), rs232Old(9), rs232(10), spsV35(11), spsRS530(12), spsRS232(13), spsX21(14), isdn(15) | ||
| trimIfRemAddress | 1.3.6.1.4.1.164.4.3.1.1.1.15 | ||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..17) | ||
| trimIfLocSubAddress | 1.3.6.1.4.1.164.4.3.1.1.1.16 | ||
| Space is not valid. If the string includes a space, the whole entry is considered not valid. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..6) | ||
| trimIfRemSubAddress | 1.3.6.1.4.1.164.4.3.1.1.1.17 | ||
| Space is not valid. If the string includes a space, the whole entry is considered not valid. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..6) | ||
| trimIfCLIVerification | 1.3.6.1.4.1.164.4.3.1.1.1.18 | ||
| Enables/Disables verification of Control Line Identification (CLI) | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimRS232Conf | 1.3.6.1.4.1.164.4.3.1.2 | ||
| OBJECT IDENTIFIER | |||
| trimBaudRate | 1.3.6.1.4.1.164.4.3.1.2.1 | ||
| Selects the baud rate used by the RS232 management interface. The default selection is 1200 bits/second. | |||
| OBJECT-TYPE | |||
| INTEGER | br300(1), br1200(2), br2400(5), br4800(7), br9600(9), br19200(10) | ||
| trimParity | 1.3.6.1.4.1.164.4.3.1.2.2 | ||
| Determines whether the parity bit will be used and determines its type. | |||
| OBJECT-TYPE | |||
| INTEGER | noParity(1), oddParity(2), evenParity(3) | ||
| trimStopBit | 1.3.6.1.4.1.164.4.3.1.2.3 | ||
| Selects the number of stop bits appended to the end of each data word. | |||
| OBJECT-TYPE | |||
| INTEGER | oneStopBit(1), twoStopBit(2) | ||
| trimThresholdRep | 1.3.6.1.4.1.164.4.3.1.3 | ||
| OBJECT IDENTIFIER | |||
| trimIfThresholdRepTable | 1.3.6.1.4.1.164.4.3.1.3.1 | ||
| ..... | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrimIfThresholdRepEntry | |||
| trimIfThresholdRepEntry | 1.3.6.1.4.1.164.4.3.1.3.1.1 | ||
| An entry in table trimIfThresholdRepTable. | |||
| OBJECT-TYPE | |||
| TrimIfThresholdRepEntry | |||
| trimIfThreRepId | 1.3.6.1.4.1.164.4.3.1.3.1.1.1 | ||
| The Interface number serves as an index to the Threshold Reoprt Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfThreRepCounterId | 1.3.6.1.4.1.164.4.3.1.3.1.1.2 | ||
| The Counter ID serves as an index to the Threshold Reoprt Table, and identify the counter for which to pot the threshold. | |||
| OBJECT-TYPE | |||
| INTEGER | vot(1) | ||
| trimThresholdValue | 1.3.6.1.4.1.164.4.3.1.3.1.1.3 | ||
| The Threshold value , this is the maximum rate of counter increments before the element issue trap. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfThreRepSampleRate | 1.3.6.1.4.1.164.4.3.1.3.1.1.4 | ||
| The network object will sample the counter atthis interval. When this parameter is set to 0, the treshold comparison is disable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimIfThreRepTrapRate | 1.3.6.1.4.1.164.4.3.1.3.1.1.5 | ||
| The network object will issue a trap according to this interval. Note that the trape interval nust be equal or larger then trimIfThreRepSampleRate. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimBackup | 1.3.6.1.4.1.164.4.3.2 | ||
| OBJECT IDENTIFIER | |||
| trimBackupState | 1.3.6.1.4.1.164.4.3.2.1 | ||
| If main - the bridge is connected via the main physical link. If backup - the automatic backup feature was enabled and the bridge is connected via the backup physical link. | |||
| OBJECT-TYPE | |||
| INTEGER | main(1), backup(2) | ||
| trimDialUpStatus | 1.3.6.1.4.1.164.4.3.2.2 | ||
| This parameter controls the operation of dial-up backup function. If status is disable(2), dial-up backup will not be initiated when the main link fails or exceeds the specified error limit. If status is enable(1), the dial-up backup will be initiated if the main link fails or if the error rate on the main link exceeds the limit specified by variable trimDialUp ErrorThreshold. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimBackLinkType | 1.3.6.1.4.1.164.4.3.2.3 | ||
| This variable specifies the type of the backup link. If the type is leased(2), Trimbridge will reroute traffic to the backup link, when main link fails. If the value is dialUp(1), then the backup dial-up procedure is initiated when the main link fails. | |||
| OBJECT-TYPE | |||
| INTEGER | dialUp(1), leased(2) | ||
| trimDialUpMode | 1.3.6.1.4.1.164.4.3.2.4 | ||
| If the mode is originate(1), Trimbridge initiates the backup procedure when the main link fails. if the mode is answer(2), it expects that the bridge on the other end of the link will initiate the backup procedure. Note that only one bridge in a pair should be set to mode originate(1). | |||
| OBJECT-TYPE | |||
| INTEGER | originate(1), answer(2) | ||
| trimDialUpErrorThreshold | 1.3.6.1.4.1.164.4.3.2.5 | ||
| Error rate on main link at which Backup will be enabled. low - 1*10-5 medium - 5*10-4 high - 1*10-3 If none(1) is selected, then backup is not invoked when there are errors on the main link, but only when the main link is down. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), low(2), medium(3), high(4) | ||
| trimDialUpRedialTimeout | 1.3.6.1.4.1.164.4.3.2.6 | ||
| If an attempt to dial up failed for the specified time, a new redial attempt will be initiated. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimDialUpRedialNum | 1.3.6.1.4.1.164.4.3.2.7 | ||
| This variable specifies the number of times to initiate the dial-up procedure. If the number of redials is set to zero (0), then the number of redials will be unlimited. Any other value will cause the dial-up procedure to terminate after the specified number of re-dial attempts fail. Resetting this variable to any value will re-initiate the dial-up procedure. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimBackUpConnectDelay | 1.3.6.1.4.1.164.4.3.2.8 | ||
| The connect delay defines the minimum time period that the link must be disconnected. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimBackUpDisConnectDelay | 1.3.6.1.4.1.164.4.3.2.9 | ||
| The disconnect delay defines the delay between the last valid traffic trigger and link disconnection. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimBackUpScheduleTable | 1.3.6.1.4.1.164.4.3.2.10 | ||
| This is a table that contains the reroute shedule for the backup link. The index is the day of the week, starting with 1 for Sunday, ending with 7 for Saturday. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrimBackUpEntry | |||
| trimBackUpEntry | 1.3.6.1.4.1.164.4.3.2.10.1 | ||
| An entry in table trimBackUpScheduleTable. | |||
| OBJECT-TYPE | |||
| TrimBackUpEntry | |||
| trimBackUpDay | 1.3.6.1.4.1.164.4.3.2.10.1.1 | ||
| The day of the week for which the entry applies. The days are numbered from 1 to 7, representing Monday through Sunday. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimBackUpFromTo | 1.3.6.1.4.1.164.4.3.2.10.1.2 | ||
| This is the time during which backup should be disabled, expressed as xx:xx-yy:yy, where x's reflect the time from and y's reflect the time to. The first two digits, in x and in y, are the hour and the second two digits are the minutes. The pairs of digits are separated by a colon, and the x is separated from the y by a dash. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| trimBackUpDelayAfterFailure | 1.3.6.1.4.1.164.4.3.2.11 | ||
| This entry defines the delay between the last @@@@ | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimTR | 1.3.6.1.4.1.164.4.3.3 | ||
| OBJECT IDENTIFIER | |||
| trimTRIfTable | 1.3.6.1.4.1.164.4.3.3.1 | ||
| This table defines configuration parameters for Token Ring interfaces in the Trimbridge-16. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrimTRIfEntry | |||
| trimTRIfEntry | 1.3.6.1.4.1.164.4.3.3.1.1 | ||
| An entry in table trimTRIfTable. | |||
| OBJECT-TYPE | |||
| TrimTRIfEntry | |||
| trimTRIfIndex | 1.3.6.1.4.1.164.4.3.3.1.1.1 | ||
| Index to the Token Ring Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trimTREarlyTokenRelease | 1.3.6.1.4.1.164.4.3.3.1.1.2 | ||
| This parameter controls the early token release. This paramenter is applicable only to 16 Mbps rings. | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimTRLocalAdminAddress | 1.3.6.1.4.1.164.4.3.3.1.1.3 | ||
| A locally administered MAC Address of this interface. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| trimTRLocalAdminAddressStatus | 1.3.6.1.4.1.164.4.3.3.1.1.4 | ||
| This parameter controls whether the bridge uses the locally administered MAC Address defined for this interface, when enable(1), or not , when disable(2). | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| trimTrapInfo | 1.3.6.1.4.1.164.4.3.4 | ||
| OBJECT IDENTIFIER | |||
| trimErrorDesc | 1.3.6.1.4.1.164.4.3.4.1 | ||
| A textual description of the enterprise-specific trap sent to the Network Management Station by Trimbridge. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| trimErrorSeverity | 1.3.6.1.4.1.164.4.3.4.2 | ||
| The severity type of the enterprise-specific trap sent to the Network Management Station by Trimbridge. | |||
| OBJECT-TYPE | |||
| INTEGER | information(1), warning(2), error(3), fatal(4) | ||
| febFtb | 1.3.6.1.4.1.164.4.4 | ||
| OBJECT IDENTIFIER | |||
| febFtbEvents | 1.3.6.1.4.1.164.4.4.0 | ||
| The events for FEBs and FTBs. | |||
| OBJECT-IDENTITY | |||
| lanTableOverflow | 1.3.6.1.4.1.164.4.4.0.1 | ||
| The station table has the maximum number of addresses for the device. | |||
| NOTIFICATION-TYPE | |||
| statusChanged | 1.3.6.1.4.1.164.4.4.0.2 | ||
| A change occured in agent status or leds. | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| agnIndication | |||
| portFddiStatusChanged | 1.3.6.1.4.1.164.4.4.0.3 | ||
| The Fddi port status changed. fddimibPORTPCMState value has become off, maint, active, connect, or exited one of these states. | |||
| NOTIFICATION-TYPE | |||
| fddimibPORTPCMState | |||
| agnLed | |||
| febFtbTranslation | 1.3.6.1.4.1.164.4.4.1 | ||
| OBJECT IDENTIFIER | |||
| febFtbTranslIfTable | 1.3.6.1.4.1.164.4.4.1.1 | ||
| The translation table defines which type of translation is required for each device interface. This is particularly important for WAN links, as the translating device does not have a knowledge of the target LAN type. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| FebFtbTranslIfEntry | |||
| febFtbTranslIfEntry | 1.3.6.1.4.1.164.4.4.1.1.1 | ||
| Entry in the translation table. | |||
| OBJECT-TYPE | |||
| FebFtbTranslIfEntry | |||
| febFtbTranslIfIndex | 1.3.6.1.4.1.164.4.4.1.1.1.1 | ||
| Index to the Translation Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| febFtbTunnelProtocol | 1.3.6.1.4.1.164.4.4.1.1.1.2 | ||
| IEEE 802.1h standard defines the tunneling for Appletalk I. This parameter enables the user to specify Ethertype of an additional protocol to tunnel (e.g. IPX). For IPX, Enter 8137 to translate Token Ring SNAP frames to Ethernet_SNAP frames (instead of Ethernet II). Valid range of values: 05DC to FFFF (hex) 0000 (hex) - disables this function. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| febFtbTranslIPXRawEthernet | 1.3.6.1.4.1.164.4.4.1.1.1.3 | ||
| This variable defines the translation mode for IPX frames in standrad Token Ring format. It is applicable to Ethernet interfaces (i.e. febFtbTranslSwitch variable has value Ethernet (2). ). ethernetRaw8023: translate to Raw Ethernet frames (default) ethernet8022: translate to Ethernet 802.2 frames. | |||
| OBJECT-TYPE | |||
| INTEGER | ethernetRaw8023(1), ethernet8022(2) | ||
| febFtbStatus | 1.3.6.1.4.1.164.4.4.2 | ||
| OBJECT IDENTIFIER | |||
| febFtbLanTable | 1.3.6.1.4.1.164.4.4.2.1 | ||
| . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| FebFtbLanTabEntry | |||
| febFtbLanTabEntry | 1.3.6.1.4.1.164.4.4.2.1.1 | ||
| Entry in the LanTab table. | |||
| OBJECT-TYPE | |||
| FebFtbLanTabEntry | |||
| febFtbLanTabIfIndex | 1.3.6.1.4.1.164.4.4.2.1.1.1 | ||
| This variable defines the related interface | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| febFtbLanTabEntNumber | 1.3.6.1.4.1.164.4.4.2.1.1.2 | ||
| This variable defines the number of entries in the LAN table reletaed to the specific interface | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| febFtbFaults | 1.3.6.1.4.1.164.4.4.2.2 | ||
| This variable defines the current device faults. It is a 32 bits variable, where each bit represents a unique fault | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mlb | 1.3.6.1.4.1.164.4.5 | ||
| OBJECT IDENTIFIER | |||
| mlbEvents | 1.3.6.1.4.1.164.4.5.0 | ||
| The events for the MLB. | |||
| OBJECT-IDENTITY | |||
| mlbLanTableOverflow | 1.3.6.1.4.1.164.4.5.0.1 | ||
| The station table has the maximum number of addresses for the LANRANger. | |||
| NOTIFICATION-TYPE | |||
| mlbStatusChanged | 1.3.6.1.4.1.164.4.5.0.2 | ||
| The trap indicates changes in the device status . | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| mlbConfig | 1.3.6.1.4.1.164.4.5.1 | ||
| OBJECT IDENTIFIER | |||
| mlbMibVersion | 1.3.6.1.4.1.164.4.5.1.1 | ||
| mlb private mib version . | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mlbPanelMedia | 1.3.6.1.4.1.164.4.5.1.2 | ||
| The panel media. It can be fiber optic connector or STP+UTP in case of copper | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), copper(2), fiberOptic(3), notSupported(4) | ||
| mlbRRFrontPanelPort | 1.3.6.1.4.1.164.4.5.1.3 | ||
| Front panel port function : MainPort / Sec.Port (case of RADring card) . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), secondary(2), main(3), notSupported(4) | ||
| mlbRRTermination | 1.3.6.1.4.1.164.4.5.1.4 | ||
| Temination switch - Split back lan and Terminate it. (case of RADring card) . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), on(2), off(3), notSupported(4) | ||
| mlbAddress | 1.3.6.1.4.1.164.4.5.2 | ||
| OBJECT IDENTIFIER | |||
| mlbAddressTable | 1.3.6.1.4.1.164.4.5.2.1 | ||
| A table that contains information about the MLB ports address . | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MlbAddressEntry | |||
| mlbAddressEntry | 1.3.6.1.4.1.164.4.5.2.1.1 | ||
| Information about a specific port that the MLB lists define. | |||
| OBJECT-TYPE | |||
| MlbAddressEntry | |||
| mlbPortIndex | 1.3.6.1.4.1.164.4.5.2.1.1.1 | ||
| A unique value for each port, equal to the value of ifIndex for the port. The maximum number of ports for mlb is 2 . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mlbBurnAddress | 1.3.6.1.4.1.164.4.5.2.1.1.2 | ||
| This is the burned-in MacAddress on the LANRANger. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| mlbLocAddress | 1.3.6.1.4.1.164.4.5.2.1.1.3 | ||
| This is a locally administered address. If a zero value appears, the network administrator did not set a locally administered address. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| mlbActiveAddress | 1.3.6.1.4.1.164.4.5.2.1.1.4 | ||
| The MAC address that is in use on the LANRANger. The address selected will appear in ifPhysAddress. | |||
| OBJECT-TYPE | |||
| INTEGER | burnedIn(1), locallyAdministered(2) | ||
| radConverters | 1.3.6.1.4.1.164.5 | ||
| OBJECT IDENTIFIER | |||
| genSnar | 1.3.6.1.4.1.164.5.1 | ||
| OBJECT IDENTIFIER | |||
| snarState | 1.3.6.1.4.1.164.5.1.1 | ||
| OBJECT IDENTIFIER | |||
| snarStatus | 1.3.6.1.4.1.164.5.1.1.1 | ||
| The status of the whole SNAR process 1 -up 2 -down 3 -test (After setting one of the previous states, the status will be test until the changes will be done). | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), test(3) | ||
| snarBufferUsage | 1.3.6.1.4.1.164.5.1.1.2 | ||
| The buffer usage of the SNAR (in percentage). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| snarMaxSnaSession | 1.3.6.1.4.1.164.5.1.1.3 | ||
| Max number of sessions supported in this SNAR implementation | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| snarSaveChanges | 1.3.6.1.4.1.164.5.1.1.5 | ||
| N/A to SNAR, only for devices. When changes are made to any configuration parameters (SNA, NVA or others) it should be stored in the device's NVRAM and then the device is restarted. Using this variable the manager can: 2 - Just save into NVRAM all configuration changes 3 - Save into NVRAM the configuration changes and restart the Device, to reflect the changes. 4 - Undo all changes since last reset or save, (without resetting the device). Load the original configuration from the NVRAM. | |||
| OBJECT-TYPE | |||
| INTEGER | noSave(1), save(2), saveAndReset(3), undoAllChanges(4) | ||
| snarNva | 1.3.6.1.4.1.164.5.1.3 | ||
| OBJECT IDENTIFIER | |||
| nvaAgentsNumber | 1.3.6.1.4.1.164.5.1.3.2 | ||
| The number of configured NetView agents | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgentTable | 1.3.6.1.4.1.164.5.1.3.3 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NvaAgentEntry | |||
| nvaAgentEntry | 1.3.6.1.4.1.164.5.1.3.3.1 | ||
| An entry in table nvaAgentTable. | |||
| OBJECT-TYPE | |||
| NvaAgentEntry | |||
| nvaAgIndex | 1.3.6.1.4.1.164.5.1.3.3.1.1 | ||
| Agent number . Range (1 - nvaAgentsNumber) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| nvaAgAdminStatus | 1.3.6.1.4.1.164.5.1.3.3.1.3 | ||
| The admin. status of NV AGENT. Value of 'disable' will prevent the NetView agent from trying to connect to the NetView management system | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| nvaAgOperState | 1.3.6.1.4.1.164.5.1.3.3.1.4 | ||
| Current Operation state of the NetView agent. Active state means that the NetView agent is in session with the NetView management system | |||
| OBJECT-TYPE | |||
| INTEGER | inactive(1), active(2) | ||
| nvaAgFilter | 1.3.6.1.4.1.164.5.1.3.3.1.5 | ||
| Alert filter bit mask. Each bit corresponds to a specific alert sent by the NetView agent. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| nvaAgAllowRunCmd | 1.3.6.1.4.1.164.5.1.3.3.1.6 | ||
| Defines whether the NetView agent is allowed to handle operational commands, received by the RUNCMD facility | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| nvaAgAccessType | 1.3.6.1.4.1.164.5.1.3.3.1.7 | ||
| Defines the method in which the agent tries to connect to the NetView management system(the SNA host) | |||
| OBJECT-TYPE | |||
| INTEGER | llcCsmacd(1), llcTokenRing(3), sdlc(6), qllcX25(10) | ||
| nvaAgIfIndex | 1.3.6.1.4.1.164.5.1.3.3.1.8 | ||
| The port number of the interface in which the NetView agent connects to the SNA host | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| nvaAgXidBlockId | 1.3.6.1.4.1.164.5.1.3.3.1.9 | ||
| The BLOCKID part of the XID information which the NetView agent should use to connect to the NetView management system (The SNA host) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| nvaAgXidBlockNum | 1.3.6.1.4.1.164.5.1.3.3.1.10 | ||
| The BLOCKNUM part of the XID information which the NetView agent should use to connect to the NetView management system (The SNA host) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(3) | ||
| nvaAgSSap | 1.3.6.1.4.1.164.5.1.3.3.1.11 | ||
| Local SAP, used for the NetView session - for LLC access type session only. | |||
| OBJECT-TYPE | |||
| Sap | |||
| nvaAgDSap | 1.3.6.1.4.1.164.5.1.3.3.1.12 | ||
| Remote(host) Sap used by the NetView agent for the SNA host connection - for LLC access session type only. | |||
| OBJECT-TYPE | |||
| Sap | |||
| nvaAgRemMacAddr | 1.3.6.1.4.1.164.5.1.3.3.1.13 | ||
| Remote(host) MAC address used by the NetView agent for the SNA host connection - for LLC access session type only. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| nvaAgSdlcAddr | 1.3.6.1.4.1.164.5.1.3.3.1.14 | ||
| SDLC address used by the NetView agent for the SNA host connection - for SDLC access session type only. | |||
| OBJECT-TYPE | |||
| SdlcAddr | |||
| nvaAgResourceName | 1.3.6.1.4.1.164.5.1.3.3.1.15 | ||
| A 4 character name that is appended to the resource name in the NetView alerts sent by the NetView agent | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| nvaAgentStatTable | 1.3.6.1.4.1.164.5.1.3.4 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| NvaAgentStatEntry | |||
| nvaAgentStatEntry | 1.3.6.1.4.1.164.5.1.3.4.1 | ||
| An entry in table nvaAgentStatTable. | |||
| OBJECT-TYPE | |||
| NvaAgentStatEntry | |||
| nvaAgStatIndex | 1.3.6.1.4.1.164.5.1.3.4.1.1 | ||
| Agent number . Range (1 - nvaAgentsNumber) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| nvaAgStatTime | 1.3.6.1.4.1.164.5.1.3.4.1.2 | ||
| Time since last reset of the NV agent statistics. Setting to a value of 0 will clear all Agents' statistics. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| nvaAgActPu | 1.3.6.1.4.1.164.5.1.3.4.1.3 | ||
| Number of session initiation (ACTPU) requests received from the SNA host | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgDactPu | 1.3.6.1.4.1.164.5.1.3.4.1.4 | ||
| Number of session disconnection (DACTPU) requests received from the SNA host | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgRpNmvt | 1.3.6.1.4.1.164.5.1.3.4.1.5 | ||
| Number of NMVTs received from the SNA host, and responded with a positive response. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgRnNmvt | 1.3.6.1.4.1.164.5.1.3.4.1.6 | ||
| Number of NMVTs received from the SNA host, and respond with a negative response. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgSpNmvt | 1.3.6.1.4.1.164.5.1.3.4.1.7 | ||
| Number of NMVTs (of any type) sent to the SNA host. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgSAlerts | 1.3.6.1.4.1.164.5.1.3.4.1.9 | ||
| Number of alert NMVTs sent by the NetView agent. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgRRunCmd | 1.3.6.1.4.1.164.5.1.3.4.1.10 | ||
| Number of RUNCMD (execute-command NMVTs) received by the NetView agent. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgSRunCmd | 1.3.6.1.4.1.164.5.1.3.4.1.11 | ||
| Number of RUNCMD replies sent to the NetView host. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| nvaAgSPdstat | 1.3.6.1.4.1.164.5.1.3.4.1.12 | ||
| Number of PDSTAT NMVTs sent by the NetView agent. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| snarSna | 1.3.6.1.4.1.164.5.1.5 | ||
| OBJECT IDENTIFIER | |||
| snaSessTable | 1.3.6.1.4.1.164.5.1.5.3 | ||
| Holding SNA session's parameters for each side of a specific session, indexed by session_id | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnaSessEntry | |||
| snaSessEntry | 1.3.6.1.4.1.164.5.1.5.3.1 | ||
| An entry in table snaSessTable. | |||
| OBJECT-TYPE | |||
| SnaSessEntry | |||
| sessIfIndex | 1.3.6.1.4.1.164.5.1.5.3.1.1 | ||
| Interface used by this SNA session | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessId | 1.3.6.1.4.1.164.5.1.5.3.1.2 | ||
| The unique identifier of the converted SNA session id | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessSide | 1.3.6.1.4.1.164.5.1.5.3.1.3 | ||
| The SNA session side. Each session handled by SNAR/device, creates 2 SNA sessions, hereafter called 'side A' and 'side B' Configuration parameters, and Statistics are defined for each side separately. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| sessDev | 1.3.6.1.4.1.164.5.1.5.3.1.4 | ||
| The device number, used in devices setup. N/A to SNAR. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessAdminStatus | 1.3.6.1.4.1.164.5.1.5.3.1.5 | ||
| Admin. status of this session, as requested by the manager. 10 - Session is invalid, and not handled by SNAR devices. 1 - Session is disabled. SNAR/Device will not try to start this session. 2- Session is enabled. SNAR/Device will try to start this session. 3- Under_creation - This session parameters are under creation, manipulated by a manager. 4 - stop: stop an enabled session immediately - no need to save change. 5 - start :start a stopped sessions immediately - no need to save change. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2), underCreation(3), stop(4), start(5), invalid(10) | ||
| sessOperState | 1.3.6.1.4.1.164.5.1.5.3.1.6 | ||
| Current operating state. See Manual reference for more information. | |||
| OBJECT-TYPE | |||
| INTEGER | stopped(1), disabled(2), sdlcProb03(3), llcProb04(4), ifProb30(30), ifProb80(80), ifProb81(81), ifProb87(87), ifProb88(88), ok(99) | ||
| sessAccessType | 1.3.6.1.4.1.164.5.1.5.3.1.7 | ||
| The access type used by this side of the converted session. | |||
| OBJECT-TYPE | |||
| INTEGER | llcCsmacd(1), llcTokenRing(3), sdlc(6), qllcX25(10) | ||
| sessSXidBlockId | 1.3.6.1.4.1.164.5.1.5.3.1.8 | ||
| The BLOCKID part of the XID information sent by this side for the SNA session initiation | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| sessSXidBlockNum | 1.3.6.1.4.1.164.5.1.5.3.1.9 | ||
| The BLOCKNUM part of the XID information sent by this side for the SNA session initiation | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(3) | ||
| sessSSap | 1.3.6.1.4.1.164.5.1.5.3.1.10 | ||
| The Local SAP used by SNAR for this session's side (LLC sessions only) | |||
| OBJECT-TYPE | |||
| Sap | |||
| sessDSap | 1.3.6.1.4.1.164.5.1.5.3.1.11 | ||
| The remote SAP used by SNAR for this session's side (LLC sessions only) | |||
| OBJECT-TYPE | |||
| Sap | |||
| sessRemMacAddr | 1.3.6.1.4.1.164.5.1.5.3.1.12 | ||
| The remote MAC address used by this session's side (LLC sessions only) | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| sessSdlcAddr | 1.3.6.1.4.1.164.5.1.5.3.1.13 | ||
| The SDLC address used by this session's side (SDLC sessions only, both primary and secondary) | |||
| OBJECT-TYPE | |||
| SdlcAddr | |||
| sessGroupPoll | 1.3.6.1.4.1.164.5.1.5.3.1.14 | ||
| The address of the group poll in which this session's side participates (SLDC secondary only). A value of 0 indicates that it doesn't participate in any group. Only one group is supported for each SDLC line (same port) | |||
| OBJECT-TYPE | |||
| SdlcAddr | |||
| sessRole | 1.3.6.1.4.1.164.5.1.5.3.1.15 | ||
| The type of SDLC session for this side. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| sessIpEncapsulated | 1.3.6.1.4.1.164.5.1.5.3.1.16 | ||
| Specified whether this session data is encapsulated within UDP/IP | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessDestIpAddr | 1.3.6.1.4.1.164.5.1.5.3.1.17 | ||
| The destination IP address (IP encapsulated sessions only). | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| sessRemX25Addr | 1.3.6.1.4.1.164.5.1.5.3.1.18 | ||
| The remote X25 address (QLLC only) . | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| snaSessTuneTable | 1.3.6.1.4.1.164.5.1.5.4 | ||
| Holding SNA session parameters for each side of a specific session, indexed by session_id | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnaSessTuneEntry | |||
| snaSessTuneEntry | 1.3.6.1.4.1.164.5.1.5.4.1 | ||
| An entry in table snaSessTuneTable. | |||
| OBJECT-TYPE | |||
| SnaSessTuneEntry | |||
| sessTuneIfIndex | 1.3.6.1.4.1.164.5.1.5.4.1.1 | ||
| The SNA session side. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessTuneId | 1.3.6.1.4.1.164.5.1.5.4.1.2 | ||
| The unique identifier of the converted SNA session. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessTuneSide | 1.3.6.1.4.1.164.5.1.5.4.1.3 | ||
| The SNA session's side. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| sessBufferSize | 1.3.6.1.4.1.164.5.1.5.4.1.4 | ||
| The max. buffer size of remote device (All sessions). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessSegmentation | 1.3.6.1.4.1.164.5.1.5.4.1.5 | ||
| Specifies whether the SNAR should perform segmentation when incoming frame on one side is longer then the sessSideBufferSize of the other size 1 - disable - don't perform segmentation 2 - enable - perform segmentation | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessFirstSide | 1.3.6.1.4.1.164.5.1.5.4.1.6 | ||
| Specifies which side of the two SNA sides (side_a or side_b) should be started first (SNAR only, N/A to devices) | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| sessWindow | 1.3.6.1.4.1.164.5.1.5.4.1.7 | ||
| The max window size (1 .. 127) for this session's side. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessDuplex | 1.3.6.1.4.1.164.5.1.5.4.1.8 | ||
| Specifies the type of SDLC device on the other end of the SDLC line. FULL- means a device capable of transmit and receive data simultaneously. | |||
| OBJECT-TYPE | |||
| INTEGER | half(1), full(2) | ||
| sessRXidBlockId | 1.3.6.1.4.1.164.5.1.5.4.1.9 | ||
| The BLOCKID part of the XID information expected to be received on this side of the SNA session | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| sessRXidBlockNum | 1.3.6.1.4.1.164.5.1.5.4.1.10 | ||
| The BLOCKNUM part of the XID information expected to be received on this side of the SNA session | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(3) | ||
| sessCheckXid | 1.3.6.1.4.1.164.5.1.5.4.1.11 | ||
| Specified whether the received XID information should be checked and compared to the value of sessRXid: 1 - disable: don't check 2 - enable : check | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessT1 | 1.3.6.1.4.1.164.5.1.5.4.1.12 | ||
| The T1 timer (in 100 msec) for this session's side. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessTi | 1.3.6.1.4.1.164.5.1.5.4.1.13 | ||
| The Ti timer (in sec) for this session | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessT2 | 1.3.6.1.4.1.164.5.1.5.4.1.14 | ||
| The T2 timer (in 100 msec) for this session | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessN2 | 1.3.6.1.4.1.164.5.1.5.4.1.15 | ||
| The N2 value for this session's side | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessUdpPort | 1.3.6.1.4.1.164.5.1.5.4.1.16 | ||
| The UDP port used by SNAR (IP encapsulated sessions only) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| snaSessStatTable | 1.3.6.1.4.1.164.5.1.5.5 | ||
| Holding SNA session parameters for each side of a specific session, indexed by session_id | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnaSessStatEntry | |||
| snaSessStatEntry | 1.3.6.1.4.1.164.5.1.5.5.1 | ||
| An entry in table snaSessStatTable. | |||
| OBJECT-TYPE | |||
| SnaSessStatEntry | |||
| sessStatIfIndex | 1.3.6.1.4.1.164.5.1.5.5.1.1 | ||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessStatId | 1.3.6.1.4.1.164.5.1.5.5.1.2 | ||
| The unique identifier of the converted SNA session. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessStatSide | 1.3.6.1.4.1.164.5.1.5.5.1.3 | ||
| The SNA session's side. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| sessStatTime | 1.3.6.1.4.1.164.5.1.5.5.1.4 | ||
| Time since last reset of this session statistics. Setting to a value of 0 will clear all session statistics. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| sessSPius | 1.3.6.1.4.1.164.5.1.5.5.1.5 | ||
| The number of PIUs sent by this session's side | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sessSBytes | 1.3.6.1.4.1.164.5.1.5.5.1.6 | ||
| The number of bytes sent by this session's side. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sessRPius | 1.3.6.1.4.1.164.5.1.5.5.1.7 | ||
| The number of PIUs received by this session | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sessRBytes | 1.3.6.1.4.1.164.5.1.5.5.1.8 | ||
| The number of bytes received by this session's side. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sessSessFailure | 1.3.6.1.4.1.164.5.1.5.5.1.9 | ||
| The number of session failures occurs to this session's side. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sessXidDenieds | 1.3.6.1.4.1.164.5.1.5.5.1.10 | ||
| The number of XID denied by this session's side | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| snaSessQllcTable | 1.3.6.1.4.1.164.5.1.5.7 | ||
| Holding SNA session parameters for each side of a specific session, indexed by session_id | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SnaSessQllcEntry | |||
| snaSessQllcEntry | 1.3.6.1.4.1.164.5.1.5.7.1 | ||
| An entry in table snaSessQllcTable. | |||
| OBJECT-TYPE | |||
| SnaSessQllcEntry | |||
| sessQllcIfIndex | 1.3.6.1.4.1.164.5.1.5.7.1.1 | ||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessQllcId | 1.3.6.1.4.1.164.5.1.5.7.1.2 | ||
| The unique identifier of the converted SNA session. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessQllcSide | 1.3.6.1.4.1.164.5.1.5.7.1.3 | ||
| The SNA session's side. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| sessInCalls | 1.3.6.1.4.1.164.5.1.5.7.1.4 | ||
| N/Allowed to accept call indicators (QLLC only) 1- disable: don't allow to accept call indications 2- enable: Allow to accept call indications | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessOutCalls | 1.3.6.1.4.1.164.5.1.5.7.1.5 | ||
| N/Allowed to initiate call requests (QLLC only) 1- disable: don't allow to initiate call requests 2- enable: Allow to initiate call requests | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessPVC | 1.3.6.1.4.1.164.5.1.5.7.1.6 | ||
| PVC being used or not (QLLC only) 1 - disable :not use 2 - enable :use | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| sessCallReqData | 1.3.6.1.4.1.164.5.1.5.7.1.7 | ||
| The user's data for call requests (QLLC only). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| sessConnReqFacility | 1.3.6.1.4.1.164.5.1.5.7.1.8 | ||
| The facilities for connection requests (QLLC only). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| sessGroupId | 1.3.6.1.4.1.164.5.1.5.7.1.9 | ||
| The facility group id (QLLC only) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| sessDtePswd | 1.3.6.1.4.1.164.5.1.5.7.1.10 | ||
| The password for local DTE (QLLC only) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| sessDteId | 1.3.6.1.4.1.164.5.1.5.7.1.11 | ||
| The identification for local DTE (QLLC only). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| sessMaxInPktSize | 1.3.6.1.4.1.164.5.1.5.7.1.12 | ||
| The max inbound packet size (QLLC only). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessMaxOutPktSize | 1.3.6.1.4.1.164.5.1.5.7.1.13 | ||
| The max outbound packet size (QLLC only). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sessCallIndReverse | 1.3.6.1.4.1.164.5.1.5.7.1.14 | ||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| cvtIfn | 1.3.6.1.4.1.164.5.2 | ||
| OBJECT IDENTIFIER | |||
| cvtSdlc | 1.3.6.1.4.1.164.5.2.1 | ||
| OBJECT IDENTIFIER | |||
| sdlcLinesNumber | 1.3.6.1.4.1.164.5.2.1.1 | ||
| OBJECT-TYPE | |||
| Integer32 | |||
| sdlcTable | 1.3.6.1.4.1.164.5.2.1.3 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SdlcEntry | |||
| sdlcEntry | 1.3.6.1.4.1.164.5.2.1.3.1 | ||
| An entry in table sdlcTable. | |||
| OBJECT-TYPE | |||
| SdlcEntry | |||
| sdlcIfIndex | 1.3.6.1.4.1.164.5.2.1.3.1.1 | ||
| The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,6], for the same interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sdlcNrz | 1.3.6.1.4.1.164.5.2.1.3.1.2 | ||
| OBJECT-TYPE | |||
| INTEGER | nrz(1), nrzi(2) | ||
| sdlcDuplex | 1.3.6.1.4.1.164.5.2.1.3.1.3 | ||
| OBJECT-TYPE | |||
| INTEGER | half(1), full(2) | ||
| sdlcClockType | 1.3.6.1.4.1.164.5.2.1.3.1.4 | ||
| OBJECT-TYPE | |||
| INTEGER | external(1), internal(2) | ||
| sdlcSpeed | 1.3.6.1.4.1.164.5.2.1.3.1.5 | ||
| OBJECT-TYPE | |||
| Integer32 | |||
| sdlcConnectorType | 1.3.6.1.4.1.164.5.2.1.3.1.6 | ||
| OBJECT-TYPE | |||
| DisplayString | |||
| sdlcRts | 1.3.6.1.4.1.164.5.2.1.3.1.7 | ||
| OBJECT-TYPE | |||
| INTEGER | constatnt(1), controled(2) | ||
| sdlcStatTable | 1.3.6.1.4.1.164.5.2.1.4 | ||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SdlcStatEntry | |||
| sdlcStatEntry | 1.3.6.1.4.1.164.5.2.1.4.1 | ||
| An entry in table sdlcStatTable. | |||
| OBJECT-TYPE | |||
| SdlcStatEntry | |||
| sdlcStatIfIndex | 1.3.6.1.4.1.164.5.2.1.4.1.1 | ||
| The value of this object identifies the interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,6], for the same interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| sdlcTimeSinceReset | 1.3.6.1.4.1.164.5.2.1.4.1.2 | ||
| The time laps since the last reset statistics. Setting the object to 0 will reset all line statistics. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| sdlcStatFramesTrans | 1.3.6.1.4.1.164.5.2.1.4.1.3 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatBytesTrans | 1.3.6.1.4.1.164.5.2.1.4.1.4 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatFramesRcv | 1.3.6.1.4.1.164.5.2.1.4.1.5 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatBytesRcv | 1.3.6.1.4.1.164.5.2.1.4.1.6 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatFramesAbort | 1.3.6.1.4.1.164.5.2.1.4.1.7 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatFramesBad | 1.3.6.1.4.1.164.5.2.1.4.1.8 | ||
| This counter holds the number of all bad frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| sdlcStatFramesCrc | 1.3.6.1.4.1.164.5.2.1.4.1.9 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| cvtDot5 | 1.3.6.1.4.1.164.5.2.2 | ||
| OBJECT IDENTIFIER | |||
| cvtDot5Table | 1.3.6.1.4.1.164.5.2.2.1 | ||
| This table contains Token Ring interface parameters and state variables. One entry per 802.3 interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CvtDot5Entry | |||
| cvtDot5Entry | 1.3.6.1.4.1.164.5.2.2.1.1 | ||
| An entry in table cvtDot5Table. | |||
| OBJECT-TYPE | |||
| CvtDot5Entry | |||
| cvtDot5IfIndex | 1.3.6.1.4.1.164.5.2.2.1.1.1 | ||
| The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,6], for the same interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cvtDot5MacAddr | 1.3.6.1.4.1.164.5.2.2.1.1.2 | ||
| OBJECT-TYPE | |||
| MacAddress | |||
| cvtDot5Commands | 1.3.6.1.4.1.164.5.2.2.1.1.3 | ||
| When this object is set to the value of open(2), the station should go into the open state. When this object is set to the value of of reset(3), the station should perform reset. When this object is set to the value of close(4), the station should go into the stopped state by removing itself from the ring. Setting this object to a value of no-op(1) has no effect. When read, this object always has a value of no-op(1). | |||
| OBJECT-TYPE | |||
| INTEGER | no-op(1), open(2), reset(3), close(4) | ||
| cvtDot5RingSpeed | 1.3.6.1.4.1.164.5.2.2.1.1.4 | ||
| The ring's bandwidth. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), oneMegabit(2), fourMegabit(3), sixteenMegabit(4) | ||
| cvtDot5ActMonParticipate | 1.3.6.1.4.1.164.5.2.2.1.1.5 | ||
| If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. Setting this object might not have an effect until the next time the interface is opened. | |||
| OBJECT-TYPE | |||
| INTEGER | true(1), false(2) | ||
| cvtDot5Functional | 1.3.6.1.4.1.164.5.2.2.1.1.6 | ||
| The bit mask of all TR functional addresses for which this interface will accept frames. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| cvtDot3 | 1.3.6.1.4.1.164.5.2.3 | ||
| OBJECT IDENTIFIER | |||
| cvtDot3Table | 1.3.6.1.4.1.164.5.2.3.1 | ||
| This table contains ETHERNET interface parameters and state variables, one entry per 802.3 interface. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CvtDot3Entry | |||
| cvtDot3Entry | 1.3.6.1.4.1.164.5.2.3.1.1 | ||
| An entry in table cvtDot3Table. | |||
| OBJECT-TYPE | |||
| CvtDot3Entry | |||
| cvtDot3IfIndex | 1.3.6.1.4.1.164.5.2.3.1.1.1 | ||
| The value of this object identifies the 802.3 interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex object, defined in [4,6], for the same interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| cvtDot3MacAddr | 1.3.6.1.4.1.164.5.2.3.1.1.2 | ||
| OBJECT-TYPE | |||
| MacAddress | |||
| cvtDot3Commands | 1.3.6.1.4.1.164.5.2.3.1.1.3 | ||
| When this object is set to the value of open(2), the station should go into the open state. of reset(3), then the station should do a reset. On a reset, all MIB counters should retain their values, if possible. Other side affects are dependent on the hardware chip set. When this object is set to the value of close(4), the station should go into the stopped state by removing itself from the ring. Setting this object to a value of no-op(1) has no effect. When read, this object always has a value of no-op(1). | |||
| OBJECT-TYPE | |||
| INTEGER | no-op(1), open(2), reset(3), close(4) | ||
| cvtDot3ActMonParticipate | 1.3.6.1.4.1.164.5.2.3.1.1.4 | ||
| If this object has a value of true(1) then this interface will participate in the active monitor selection process. If the value is false(2) then it will not. Setting this object might not have an effect until the next time the interface is opened. | |||
| OBJECT-TYPE | |||
| INTEGER | true(1), false(2) | ||
| cvtDot3Functional | 1.3.6.1.4.1.164.5.2.3.1.1.5 | ||
| The bit mask of all Ethernet functional addresses for which this interface will accept frames. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| radGen | 1.3.6.1.4.1.164.6 | ||
| OBJECT IDENTIFIER | |||
| systems | 1.3.6.1.4.1.164.6.1 | ||
| OBJECT IDENTIFIER | |||
| systemsEvents | 1.3.6.1.4.1.164.6.1.0 | ||
| The events for RAD products. | |||
| OBJECT-IDENTITY | |||
| tftpStatusChangeTrap | 1.3.6.1.4.1.164.6.1.0.1 | ||
| This trap is sent whenever the status of tftp changed. | |||
| NOTIFICATION-TYPE | |||
| tftpStatus | |||
| agnStatusChangeTrap | 1.3.6.1.4.1.164.6.1.0.2 | ||
| This trap is sent whenever the state of the entity the agent is responsible for changed. TDM devices will send agnTestStatus variable to indicate the current test status. | |||
| NOTIFICATION-TYPE | |||
| agnIndication | |||
| prtStatusChangeTrap | 1.3.6.1.4.1.164.6.1.0.3 | ||
| This trap is sent whenever the state of a port changed. Attached, will be parameter/s that indicate the new port status. The attached variables will be specified in the specifications of the products supporting this trap. | |||
| NOTIFICATION-TYPE | |||
| swdlStatusResult | 1.3.6.1.4.1.164.6.1.0.4 | ||
| This notification is sent when Software Down Load is finished. The attached object indicates the File Name. | |||
| NOTIFICATION-TYPE | |||
| swdlStatusFileName | |||
| intSwdlSlotFileMismatch | 1.3.6.1.4.1.164.6.1.0.5 | ||
| This notification is sent when the card in the chosen slot doesn't match the chosen file. The attached object indicates the File Name. | |||
| NOTIFICATION-TYPE | |||
| intSwdlFileName | |||
| agnCounterChange | 1.3.6.1.4.1.164.6.1.0.6 | ||
| This notification is sent when the value of a specific Counter is changed. Agent can send as attached object the updated Counter. For details about this Counter and attached object, see spec of the relevant application. | |||
| NOTIFICATION-TYPE | |||
| prtClkSrcChangeTrap | 1.3.6.1.4.1.164.6.1.0.7 | ||
| This trap is sent upon any port clock change. | |||
| NOTIFICATION-TYPE | |||
| moduleFailTrap | 1.3.6.1.4.1.164.6.1.0.8 | ||
| This trap is sent upon a module failure. | |||
| NOTIFICATION-TYPE | |||
| moduleInitFailTrap | 1.3.6.1.4.1.164.6.1.0.9 | ||
| This trap is sent upon a module initialization failure. | |||
| NOTIFICATION-TYPE | |||
| clkSrcChangeTrap | 1.3.6.1.4.1.164.6.1.0.10 | ||
| This trap is sent upon any change in Clock Source. | |||
| NOTIFICATION-TYPE | |||
| agnUploadDataTrap | 1.3.6.1.4.1.164.6.1.0.11 | ||
| This trap is sent upon an upload data session termination. For more details see product specification. | |||
| NOTIFICATION-TYPE | |||
| enrollmentTrap | 1.3.6.1.4.1.164.6.1.0.12 | ||
| This trap is a periodic trap, which is sent to manager until Agent gets any response (Get or Set) from this manager. | |||
| NOTIFICATION-TYPE | |||
| agnPowerFailureTrap | 1.3.6.1.4.1.164.6.1.0.13 | ||
| This trap is sent upon power failure. It is applicable for devices having one PS unit, which sense in advance the failure, and still have time to send this trap before it goes off. | |||
| NOTIFICATION-TYPE | |||
| radSysTR | 1.3.6.1.4.1.164.6.1.1 | ||
| OBJECT IDENTIFIER | |||
| radRADring | 1.3.6.1.4.1.164.6.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| radTMA | 1.3.6.1.4.1.164.6.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| radRingMonitor | 1.3.6.1.4.1.164.6.1.1.3 | ||
| OBJECT IDENTIFIER | |||
| radSysFddi | 1.3.6.1.4.1.164.6.1.2 | ||
| OBJECT IDENTIFIER | |||
| radFDX100 | 1.3.6.1.4.1.164.6.1.2.1 | ||
| OBJECT IDENTIFIER | |||
| radSysWan | 1.3.6.1.4.1.164.6.1.3 | ||
| OBJECT IDENTIFIER | |||
| radSysWanEvents | 1.3.6.1.4.1.164.6.1.3.0 | ||
| The events for RAD Wan products. | |||
| OBJECT-IDENTITY | |||
| imxAlarmTrap | 1.3.6.1.4.1.164.6.1.3.0.2 | ||
| The trap is sent every time a new alarm is logged into the alarm buffer. The trap may not be sent more than once in a five second interval. | |||
| NOTIFICATION-TYPE | |||
| imxCallLogTrap | 1.3.6.1.4.1.164.6.1.3.0.3 | ||
| The trap is sent every time a new call log entry is logged into the log buffer. The trap may not be sent more than once in a five second interval. | |||
| NOTIFICATION-TYPE | |||
| imxPingTrap | 1.3.6.1.4.1.164.6.1.3.0.4 | ||
| The trap is sent every time a ping operation is performed on a channel. | |||
| NOTIFICATION-TYPE | |||
| chStatOperStatus | |||
| radMP2100 | 1.3.6.1.4.1.164.6.1.3.1 | ||
| OBJECT IDENTIFIER | |||
| radMP2104 | 1.3.6.1.4.1.164.6.1.3.2 | ||
| OBJECT IDENTIFIER | |||
| radMP2100B | 1.3.6.1.4.1.164.6.1.3.3 | ||
| OBJECT IDENTIFIER | |||
| radMP2100F | 1.3.6.1.4.1.164.6.1.3.4 | ||
| OBJECT IDENTIFIER | |||
| radMP2100H | 1.3.6.1.4.1.164.6.1.3.5 | ||
| OBJECT IDENTIFIER | |||
| radMP2104H | 1.3.6.1.4.1.164.6.1.3.6 | ||
| OBJECT IDENTIFIER | |||
| radMP2200B | 1.3.6.1.4.1.164.6.1.3.7 | ||
| OBJECT IDENTIFIER | |||
| radMP2200F | 1.3.6.1.4.1.164.6.1.3.8 | ||
| OBJECT IDENTIFIER | |||
| radMX3000 | 1.3.6.1.4.1.164.6.1.3.9 | ||
| OBJECT IDENTIFIER | |||
| radMX3004 | 1.3.6.1.4.1.164.6.1.3.10 | ||
| OBJECT IDENTIFIER | |||
| radMX30 | 1.3.6.1.4.1.164.6.1.3.11 | ||
| OBJECT IDENTIFIER | |||
| radMX300 | 1.3.6.1.4.1.164.6.1.3.12 | ||
| OBJECT IDENTIFIER | |||
| radVOIP | 1.3.6.1.4.1.164.6.1.3.13 | ||
| OBJECT IDENTIFIER | |||
| radKM2100 | 1.3.6.1.4.1.164.6.1.3.15 | ||
| OBJECT IDENTIFIER | |||
| radKM2104 | 1.3.6.1.4.1.164.6.1.3.16 | ||
| OBJECT IDENTIFIER | |||
| radDXC30 | 1.3.6.1.4.1.164.6.1.3.20 | ||
| OBJECT IDENTIFIER | |||
| radDXC10A | 1.3.6.1.4.1.164.6.1.3.21 | ||
| OBJECT IDENTIFIER | |||
| radDXC8R | 1.3.6.1.4.1.164.6.1.3.22 | ||
| OBJECT IDENTIFIER | |||
| radDXC30E | 1.3.6.1.4.1.164.6.1.3.23 | ||
| OBJECT IDENTIFIER | |||
| radDXC3000 | 1.3.6.1.4.1.164.6.1.3.24 | ||
| OBJECT IDENTIFIER | |||
| radDXC8RNew | 1.3.6.1.4.1.164.6.1.3.25 | ||
| OBJECT IDENTIFIER | |||
| radFcdE1L | 1.3.6.1.4.1.164.6.1.3.29 | ||
| OBJECT IDENTIFIER | |||
| radFcdT1 | 1.3.6.1.4.1.164.6.1.3.30 | ||
| OBJECT IDENTIFIER | |||
| radFcdE1 | 1.3.6.1.4.1.164.6.1.3.31 | ||
| OBJECT IDENTIFIER | |||
| radFcdE1I | 1.3.6.1.4.1.164.6.1.3.32 | ||
| OBJECT IDENTIFIER | |||
| radFcdT1M | 1.3.6.1.4.1.164.6.1.3.33 | ||
| OBJECT IDENTIFIER | |||
| radFcdE1M | 1.3.6.1.4.1.164.6.1.3.34 | ||
| OBJECT IDENTIFIER | |||
| radFcdIP | 1.3.6.1.4.1.164.6.1.3.35 | ||
| OBJECT IDENTIFIER | |||
| radFcdT1A | 1.3.6.1.4.1.164.6.1.3.36 | ||
| OBJECT IDENTIFIER | |||
| radFcdE1A | 1.3.6.1.4.1.164.6.1.3.37 | ||
| OBJECT IDENTIFIER | |||
| radFcdW | 1.3.6.1.4.1.164.6.1.3.38 | ||
| OBJECT IDENTIFIER | |||
| radFcdSTM | 1.3.6.1.4.1.164.6.1.3.39 | ||
| OBJECT IDENTIFIER | |||
| radHtuE1Sa | 1.3.6.1.4.1.164.6.1.3.40 | ||
| OBJECT IDENTIFIER | |||
| radHtuE1 | 1.3.6.1.4.1.164.6.1.3.41 | ||
| OBJECT IDENTIFIER | |||
| radHtu2Sa | 1.3.6.1.4.1.164.6.1.3.42 | ||
| OBJECT IDENTIFIER | |||
| radHtu2 | 1.3.6.1.4.1.164.6.1.3.43 | ||
| OBJECT IDENTIFIER | |||
| radAsmi450R768Sa | 1.3.6.1.4.1.164.6.1.3.44 | ||
| OBJECT IDENTIFIER | |||
| radAsmi450R768 | 1.3.6.1.4.1.164.6.1.3.45 | ||
| OBJECT IDENTIFIER | |||
| radAsmi450R1152Sa | 1.3.6.1.4.1.164.6.1.3.46 | ||
| OBJECT IDENTIFIER | |||
| radAsmi450R1152 | 1.3.6.1.4.1.164.6.1.3.47 | ||
| OBJECT IDENTIFIER | |||
| radLrs12F | 1.3.6.1.4.1.164.6.1.3.48 | ||
| OBJECT IDENTIFIER | |||
| radLrs12B | 1.3.6.1.4.1.164.6.1.3.49 | ||
| OBJECT IDENTIFIER | |||
| radLrs52 | 1.3.6.1.4.1.164.6.1.3.50 | ||
| OBJECT IDENTIFIER | |||
| radHcdE1Sa | 1.3.6.1.4.1.164.6.1.3.51 | ||
| OBJECT IDENTIFIER | |||
| radHcdE1 | 1.3.6.1.4.1.164.6.1.3.52 | ||
| OBJECT IDENTIFIER | |||
| radHtuT1Sa | 1.3.6.1.4.1.164.6.1.3.53 | ||
| OBJECT IDENTIFIER | |||
| radHtuT1 | 1.3.6.1.4.1.164.6.1.3.54 | ||
| OBJECT IDENTIFIER | |||
| radOptimux4E1 | 1.3.6.1.4.1.164.6.1.3.55 | ||
| OBJECT IDENTIFIER | |||
| radOptimux4T1 | 1.3.6.1.4.1.164.6.1.3.56 | ||
| OBJECT IDENTIFIER | |||
| radOptimuxXLE1 | 1.3.6.1.4.1.164.6.1.3.57 | ||
| OBJECT IDENTIFIER | |||
| radOptimuxXLT1 | 1.3.6.1.4.1.164.6.1.3.58 | ||
| OBJECT IDENTIFIER | |||
| radOptimuxXL16E1 | 1.3.6.1.4.1.164.6.1.3.59 | ||
| OBJECT IDENTIFIER | |||
| radImx64 | 1.3.6.1.4.1.164.6.1.3.60 | ||
| OBJECT IDENTIFIER | |||
| radImx6L | 1.3.6.1.4.1.164.6.1.3.61 | ||
| OBJECT IDENTIFIER | |||
| radImx2 | 1.3.6.1.4.1.164.6.1.3.62 | ||
| OBJECT IDENTIFIER | |||
| radImx4T1 | 1.3.6.1.4.1.164.6.1.3.63 | ||
| OBJECT IDENTIFIER | |||
| radImx4E1 | 1.3.6.1.4.1.164.6.1.3.64 | ||
| OBJECT IDENTIFIER | |||
| radImx2T1E1 | 1.3.6.1.4.1.164.6.1.3.65 | ||
| OBJECT IDENTIFIER | |||
| radImxi4 | 1.3.6.1.4.1.164.6.1.3.66 | ||
| OBJECT IDENTIFIER | |||
| radOptimux4T1L | 1.3.6.1.4.1.164.6.1.3.68 | ||
| OBJECT IDENTIFIER | |||
| radOptimux4E1L | 1.3.6.1.4.1.164.6.1.3.69 | ||
| OBJECT IDENTIFIER | |||
| radHtuE1SaV2 | 1.3.6.1.4.1.164.6.1.3.70 | ||
| OBJECT IDENTIFIER | |||
| radHtuE1V2 | 1.3.6.1.4.1.164.6.1.3.71 | ||
| OBJECT IDENTIFIER | |||
| radFomiE3 | 1.3.6.1.4.1.164.6.1.3.72 | ||
| OBJECT IDENTIFIER | |||
| radFomiT3 | 1.3.6.1.4.1.164.6.1.3.73 | ||
| OBJECT IDENTIFIER | |||
| radOpt4E1C | 1.3.6.1.4.1.164.6.1.3.74 | ||
| OBJECT IDENTIFIER | |||
| radOpt4T1C | 1.3.6.1.4.1.164.6.1.3.75 | ||
| OBJECT IDENTIFIER | |||
| radPrbiE3 | 1.3.6.1.4.1.164.6.1.3.76 | ||
| OBJECT IDENTIFIER | |||
| radPrbiT3 | 1.3.6.1.4.1.164.6.1.3.77 | ||
| OBJECT IDENTIFIER | |||
| radHcd4Sa | 1.3.6.1.4.1.164.6.1.3.78 | ||
| OBJECT IDENTIFIER | |||
| radOptimuxT3 | 1.3.6.1.4.1.164.6.1.3.79 | ||
| OBJECT IDENTIFIER | |||
| radFRmon | 1.3.6.1.4.1.164.6.1.3.80 | ||
| OBJECT IDENTIFIER | |||
| radIpMux4 | 1.3.6.1.4.1.164.6.1.3.81 | ||
| OBJECT IDENTIFIER | |||
| radIpMux1 | 1.3.6.1.4.1.164.6.1.3.82 | ||
| OBJECT IDENTIFIER | |||
| radIpMux16 | 1.3.6.1.4.1.164.6.1.3.83 | ||
| OBJECT IDENTIFIER | |||
| radIpMux1E | 1.3.6.1.4.1.164.6.1.3.84 | ||
| OBJECT IDENTIFIER | |||
| radVmux2100 | 1.3.6.1.4.1.164.6.1.3.85 | ||
| OBJECT IDENTIFIER | |||
| radVmux110 | 1.3.6.1.4.1.164.6.1.3.88 | ||
| OBJECT IDENTIFIER | |||
| radIpMux8 | 1.3.6.1.4.1.164.6.1.3.91 | ||
| OBJECT IDENTIFIER | |||
| radSysBRG | 1.3.6.1.4.1.164.6.1.4 | ||
| OBJECT IDENTIFIER | |||
| radTRE1 | 1.3.6.1.4.1.164.6.1.4.1 | ||
| OBJECT IDENTIFIER | |||
| radTRE1D | 1.3.6.1.4.1.164.6.1.4.2 | ||
| OBJECT IDENTIFIER | |||
| radTRE8 | 1.3.6.1.4.1.164.6.1.4.3 | ||
| OBJECT IDENTIFIER | |||
| radTRE8D | 1.3.6.1.4.1.164.6.1.4.4 | ||
| OBJECT IDENTIFIER | |||
| radMBE1 | 1.3.6.1.4.1.164.6.1.4.5 | ||
| OBJECT IDENTIFIER | |||
| radMBE1D | 1.3.6.1.4.1.164.6.1.4.6 | ||
| OBJECT IDENTIFIER | |||
| radMBE8 | 1.3.6.1.4.1.164.6.1.4.7 | ||
| OBJECT IDENTIFIER | |||
| radMBE8D | 1.3.6.1.4.1.164.6.1.4.8 | ||
| OBJECT IDENTIFIER | |||
| radMLBT | 1.3.6.1.4.1.164.6.1.4.9 | ||
| OBJECT IDENTIFIER | |||
| radFEB4DAS | 1.3.6.1.4.1.164.6.1.4.10 | ||
| OBJECT IDENTIFIER | |||
| radTrimBrg10 | 1.3.6.1.4.1.164.6.1.4.11 | ||
| OBJECT IDENTIFIER | |||
| radTrimBrg16 | 1.3.6.1.4.1.164.6.1.4.12 | ||
| OBJECT IDENTIFIER | |||
| radRRTRE8 | 1.3.6.1.4.1.164.6.1.4.13 | ||
| OBJECT IDENTIFIER | |||
| radRRTRE8D | 1.3.6.1.4.1.164.6.1.4.14 | ||
| OBJECT IDENTIFIER | |||
| radRRMLBT | 1.3.6.1.4.1.164.6.1.4.15 | ||
| OBJECT IDENTIFIER | |||
| radRRMLBTF | 1.3.6.1.4.1.164.6.1.4.16 | ||
| OBJECT IDENTIFIER | |||
| radRRTRE1D | 1.3.6.1.4.1.164.6.1.4.17 | ||
| OBJECT IDENTIFIER | |||
| radTRERAS | 1.3.6.1.4.1.164.6.1.4.18 | ||
| OBJECT IDENTIFIER | |||
| radTRERASa | 1.3.6.1.4.1.164.6.1.4.19 | ||
| OBJECT IDENTIFIER | |||
| radMBERAS | 1.3.6.1.4.1.164.6.1.4.20 | ||
| OBJECT IDENTIFIER | |||
| radMBERASa | 1.3.6.1.4.1.164.6.1.4.21 | ||
| OBJECT IDENTIFIER | |||
| radFEB4FDX | 1.3.6.1.4.1.164.6.1.4.22 | ||
| OBJECT IDENTIFIER | |||
| radFEB4SAS | 1.3.6.1.4.1.164.6.1.4.23 | ||
| OBJECT IDENTIFIER | |||
| radRRFTBDAS | 1.3.6.1.4.1.164.6.1.4.24 | ||
| OBJECT IDENTIFIER | |||
| radRRFTBSAS | 1.3.6.1.4.1.164.6.1.4.25 | ||
| OBJECT IDENTIFIER | |||
| radFTBDAS | 1.3.6.1.4.1.164.6.1.4.26 | ||
| OBJECT IDENTIFIER | |||
| radFTBSAS | 1.3.6.1.4.1.164.6.1.4.27 | ||
| OBJECT IDENTIFIER | |||
| radFastWay100 | 1.3.6.1.4.1.164.6.1.4.28 | ||
| OBJECT IDENTIFIER | |||
| radSysCnvrtr | 1.3.6.1.4.1.164.6.1.5 | ||
| OBJECT IDENTIFIER | |||
| radSTC1 | 1.3.6.1.4.1.164.6.1.5.1 | ||
| OBJECT IDENTIFIER | |||
| radSTC2 | 1.3.6.1.4.1.164.6.1.5.3 | ||
| OBJECT IDENTIFIER | |||
| radSTC1UDP | 1.3.6.1.4.1.164.6.1.5.4 | ||
| OBJECT IDENTIFIER | |||
| radSTC2UDP | 1.3.6.1.4.1.164.6.1.5.6 | ||
| OBJECT IDENTIFIER | |||
| radFTC1 | 1.3.6.1.4.1.164.6.1.5.10 | ||
| OBJECT IDENTIFIER | |||
| radFTC2 | 1.3.6.1.4.1.164.6.1.5.12 | ||
| OBJECT IDENTIFIER | |||
| radFTC1UDP | 1.3.6.1.4.1.164.6.1.5.13 | ||
| OBJECT IDENTIFIER | |||
| radFTC2UDP | 1.3.6.1.4.1.164.6.1.5.15 | ||
| OBJECT IDENTIFIER | |||
| radSEC1 | 1.3.6.1.4.1.164.6.1.5.20 | ||
| OBJECT IDENTIFIER | |||
| radSEC2 | 1.3.6.1.4.1.164.6.1.5.22 | ||
| OBJECT IDENTIFIER | |||
| radSEC1UDP | 1.3.6.1.4.1.164.6.1.5.23 | ||
| OBJECT IDENTIFIER | |||
| radSEC2UDP | 1.3.6.1.4.1.164.6.1.5.25 | ||
| OBJECT IDENTIFIER | |||
| radFEC1 | 1.3.6.1.4.1.164.6.1.5.30 | ||
| OBJECT IDENTIFIER | |||
| radFEC2 | 1.3.6.1.4.1.164.6.1.5.32 | ||
| OBJECT IDENTIFIER | |||
| radFEC1UDP | 1.3.6.1.4.1.164.6.1.5.33 | ||
| OBJECT IDENTIFIER | |||
| radFEC2UDP | 1.3.6.1.4.1.164.6.1.5.35 | ||
| OBJECT IDENTIFIER | |||
| radSysStkHub | 1.3.6.1.4.1.164.6.1.7 | ||
| OBJECT IDENTIFIER | |||
| radRBHE | 1.3.6.1.4.1.164.6.1.7.1 | ||
| OBJECT IDENTIFIER | |||
| radRBHEEvents | 1.3.6.1.4.1.164.6.1.7.1.0 | ||
| The events for RAD Stackable products. | |||
| OBJECT-IDENTITY | |||
| resetRequired | 1.3.6.1.4.1.164.6.1.7.1.0.10 | ||
| This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable radBridgeAction. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| compNotActive | 1.3.6.1.4.1.164.6.1.7.1.0.20 | ||
| Compression was enabled but cannot be activated, since connected device does not support correct compression. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| noCompression | 1.3.6.1.4.1.164.6.1.7.1.0.21 | ||
| Compression card not present. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| errorBackUp | 1.3.6.1.4.1.164.6.1.7.1.0.22 | ||
| Automatic switchover to backup link because of excessive link errors. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| faultBackUp | 1.3.6.1.4.1.164.6.1.7.1.0.23 | ||
| Automatic switchover to backup link because of main link fault. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| mainLinkUp | 1.3.6.1.4.1.164.6.1.7.1.0.24 | ||
| Communication returned to main link. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| failedDialUp | 1.3.6.1.4.1.164.6.1.7.1.0.25 | ||
| Cannot establish backup dial-up connection. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| extLoopBack | 1.3.6.1.4.1.164.6.1.7.1.0.29 | ||
| This trap is sent when Loopback starts on the link. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| dialUpConnFailed | 1.3.6.1.4.1.164.6.1.7.1.0.41 | ||
| This trap is sent when the dialUp connection is terminated due to a failure. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| dialUpConnEstablished | 1.3.6.1.4.1.164.6.1.7.1.0.42 | ||
| This trap is sent when the dialUp connection is established. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| radRBHT | 1.3.6.1.4.1.164.6.1.7.2 | ||
| OBJECT IDENTIFIER | |||
| radRBHTEvents | 1.3.6.1.4.1.164.6.1.7.2.0 | ||
| The events for RAD Stackable products. | |||
| OBJECT-IDENTITY | |||
| ringBeaconing | 1.3.6.1.4.1.164.6.1.7.2.0.30 | ||
| This trap is sent when Token Ring LAN is beaconing. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| lanAdapterRemoved | 1.3.6.1.4.1.164.6.1.7.2.0.31 | ||
| This trap is sent when Token Ring LAN adapter was removed by LAN manager. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| dialUpConnTerminated | 1.3.6.1.4.1.164.6.1.7.2.0.43 | ||
| This trap is sent when the dialUp connection is normally terminated. | |||
| NOTIFICATION-TYPE | |||
| trimErrorDesc | |||
| trimErrorSeverity | |||
| agnLed | |||
| radETS4fddiDAS | 1.3.6.1.4.1.164.6.1.7.3 | ||
| OBJECT IDENTIFIER | |||
| radETS4fddiSAS | 1.3.6.1.4.1.164.6.1.7.4 | ||
| OBJECT IDENTIFIER | |||
| radSAHEMX | 1.3.6.1.4.1.164.6.1.7.5 | ||
| OBJECT IDENTIFIER | |||
| radSAHTM | 1.3.6.1.4.1.164.6.1.7.6 | ||
| OBJECT IDENTIFIER | |||
| radETS4 | 1.3.6.1.4.1.164.6.1.7.7 | ||
| OBJECT IDENTIFIER | |||
| radSAHEMU | 1.3.6.1.4.1.164.6.1.7.8 | ||
| OBJECT IDENTIFIER | |||
| unknown | 1.3.6.1.4.1.164.6.1.7.9 | ||
| OBJECT IDENTIFIER | |||
| radSAH16Eint | 1.3.6.1.4.1.164.6.1.7.10 | ||
| OBJECT IDENTIFIER | |||
| radSAH16Tint | 1.3.6.1.4.1.164.6.1.7.11 | ||
| OBJECT IDENTIFIER | |||
| radSAH16Eext | 1.3.6.1.4.1.164.6.1.7.12 | ||
| OBJECT IDENTIFIER | |||
| radSAH16Text | 1.3.6.1.4.1.164.6.1.7.13 | ||
| OBJECT IDENTIFIER | |||
| radSysPS | 1.3.6.1.4.1.164.6.1.8 | ||
| OBJECT IDENTIFIER | |||
| radSysPSEvents | 1.3.6.1.4.1.164.6.1.8.0 | ||
| The events for RAD Packet Switch (PS) products. | |||
| OBJECT-IDENTITY | |||
| linkProtocolChanged | 1.3.6.1.4.1.164.6.1.8.0.1 | ||
| Upon setting of a new protocol to a specific interface. | |||
| NOTIFICATION-TYPE | |||
| pktSwchPhyInterfaceIfIndex | |||
| pktSwchPhyInterfaceProtocolA | |||
| enrollmentPS | 1.3.6.1.4.1.164.6.1.8.0.2 | ||
| Periodic trap to be sent to the list of managers. | |||
| NOTIFICATION-TYPE | |||
| rtsChange | 1.3.6.1.4.1.164.6.1.8.0.3 | ||
| NOTIFICATION-TYPE | |||
| pktSwchChannelNumberA | |||
| ledStatusChange | 1.3.6.1.4.1.164.6.1.8.0.4 | ||
| The trap is sent when one of the Hazard LEDs has changed. | |||
| NOTIFICATION-TYPE | |||
| agnLed | |||
| radSPS2 | 1.3.6.1.4.1.164.6.1.8.1 | ||
| OBJECT IDENTIFIER | |||
| radSPS3 | 1.3.6.1.4.1.164.6.1.8.2 | ||
| OBJECT IDENTIFIER | |||
| radSPS6 | 1.3.6.1.4.1.164.6.1.8.3 | ||
| OBJECT IDENTIFIER | |||
| radSPS9 | 1.3.6.1.4.1.164.6.1.8.4 | ||
| OBJECT IDENTIFIER | |||
| radSPS12 | 1.3.6.1.4.1.164.6.1.8.5 | ||
| OBJECT IDENTIFIER | |||
| radAPD2 | 1.3.6.1.4.1.164.6.1.8.6 | ||
| OBJECT IDENTIFIER | |||
| radAPD8 | 1.3.6.1.4.1.164.6.1.8.7 | ||
| OBJECT IDENTIFIER | |||
| radAPS8 | 1.3.6.1.4.1.164.6.1.8.8 | ||
| OBJECT IDENTIFIER | |||
| radAPS16 | 1.3.6.1.4.1.164.6.1.8.9 | ||
| OBJECT IDENTIFIER | |||
| radAPS24 | 1.3.6.1.4.1.164.6.1.8.10 | ||
| OBJECT IDENTIFIER | |||
| radSPS3S | 1.3.6.1.4.1.164.6.1.8.11 | ||
| OBJECT IDENTIFIER | |||
| radFPS8 | 1.3.6.1.4.1.164.6.1.8.12 | ||
| OBJECT IDENTIFIER | |||
| radFPS12 | 1.3.6.1.4.1.164.6.1.8.13 | ||
| OBJECT IDENTIFIER | |||
| radSPS3ScSL | 1.3.6.1.4.1.164.6.1.8.14 | ||
| OBJECT IDENTIFIER | |||
| radSPS3Sc2S | 1.3.6.1.4.1.164.6.1.8.15 | ||
| OBJECT IDENTIFIER | |||
| radFPS8c | 1.3.6.1.4.1.164.6.1.8.16 | ||
| OBJECT IDENTIFIER | |||
| radFPS4 | 1.3.6.1.4.1.164.6.1.8.17 | ||
| OBJECT IDENTIFIER | |||
| radSysEth | 1.3.6.1.4.1.164.6.1.9 | ||
| OBJECT IDENTIFIER | |||
| radEP8T | 1.3.6.1.4.1.164.6.1.9.1 | ||
| OBJECT IDENTIFIER | |||
| radEP4TAUI | 1.3.6.1.4.1.164.6.1.9.2 | ||
| OBJECT IDENTIFIER | |||
| radEP4T2FL | 1.3.6.1.4.1.164.6.1.9.3 | ||
| OBJECT IDENTIFIER | |||
| radEP4TFL | 1.3.6.1.4.1.164.6.1.9.4 | ||
| OBJECT IDENTIFIER | |||
| radEP4FL | 1.3.6.1.4.1.164.6.1.9.5 | ||
| OBJECT IDENTIFIER | |||
| radEPR8T | 1.3.6.1.4.1.164.6.1.9.7 | ||
| OBJECT IDENTIFIER | |||
| radEPR4TAUI | 1.3.6.1.4.1.164.6.1.9.8 | ||
| OBJECT IDENTIFIER | |||
| radEPR4T2FL | 1.3.6.1.4.1.164.6.1.9.9 | ||
| OBJECT IDENTIFIER | |||
| radEPR4TFL | 1.3.6.1.4.1.164.6.1.9.10 | ||
| OBJECT IDENTIFIER | |||
| radEPR4FL | 1.3.6.1.4.1.164.6.1.9.11 | ||
| OBJECT IDENTIFIER | |||
| radSysRtr | 1.3.6.1.4.1.164.6.1.11 | ||
| OBJECT IDENTIFIER | |||
| radSysRtrEvents | 1.3.6.1.4.1.164.6.1.11.0 | ||
| The events for RAD Router products. | |||
| OBJECT-IDENTITY | |||
| radRTED | 1.3.6.1.4.1.164.6.1.11.1 | ||
| OBJECT IDENTIFIER | |||
| radRTEM | 1.3.6.1.4.1.164.6.1.11.2 | ||
| OBJECT IDENTIFIER | |||
| radRTEC | 1.3.6.1.4.1.164.6.1.11.3 | ||
| OBJECT IDENTIFIER | |||
| radWebRanger | 1.3.6.1.4.1.164.6.1.11.4 | ||
| OBJECT IDENTIFIER | |||
| radTinyRouter | 1.3.6.1.4.1.164.6.1.11.5 | ||
| OBJECT IDENTIFIER | |||
| radLA240 | 1.3.6.1.4.1.164.6.1.11.6 | ||
| OBJECT IDENTIFIER | |||
| radSuperLan | 1.3.6.1.4.1.164.6.1.11.7 | ||
| OBJECT IDENTIFIER | |||
| radLA240I | 1.3.6.1.4.1.164.6.1.11.8 | ||
| OBJECT IDENTIFIER | |||
| radFcdIsdn | 1.3.6.1.4.1.164.6.1.11.9 | ||
| OBJECT IDENTIFIER | |||
| radEFcdIp | 1.3.6.1.4.1.164.6.1.11.10 | ||
| OBJECT IDENTIFIER | |||
| radFcdIpD | 1.3.6.1.4.1.164.6.1.11.11 | ||
| OBJECT IDENTIFIER | |||
| radFcdIpM | 1.3.6.1.4.1.164.6.1.11.12 | ||
| OBJECT IDENTIFIER | |||
| radSysAtm | 1.3.6.1.4.1.164.6.1.12 | ||
| OBJECT IDENTIFIER | |||
| radSysAtmEvents | 1.3.6.1.4.1.164.6.1.12.0 | ||
| The events for RAD ATM products. | |||
| OBJECT-IDENTITY | |||
| radStarSwitch | 1.3.6.1.4.1.164.6.1.12.1 | ||
| OBJECT IDENTIFIER | |||
| radStarSwitchATM25 | 1.3.6.1.4.1.164.6.1.12.1.1 | ||
| OBJECT IDENTIFIER | |||
| radStarSwitchATM25L | 1.3.6.1.4.1.164.6.1.12.1.2 | ||
| OBJECT IDENTIFIER | |||
| radStarSwitchATM155 | 1.3.6.1.4.1.164.6.1.12.1.3 | ||
| OBJECT IDENTIFIER | |||
| radAtmCsuDsu | 1.3.6.1.4.1.164.6.1.12.2 | ||
| OBJECT IDENTIFIER | |||
| radAmcdE1 | 1.3.6.1.4.1.164.6.1.12.2.1 | ||
| OBJECT IDENTIFIER | |||
| radAmcdT1 | 1.3.6.1.4.1.164.6.1.12.2.2 | ||
| OBJECT IDENTIFIER | |||
| radAce20E | 1.3.6.1.4.1.164.6.1.12.2.3 | ||
| OBJECT IDENTIFIER | |||
| radAce20T | 1.3.6.1.4.1.164.6.1.12.2.4 | ||
| OBJECT IDENTIFIER | |||
| radAce2005 | 1.3.6.1.4.1.164.6.1.12.2.5 | ||
| OBJECT IDENTIFIER | |||
| radAce2002 | 1.3.6.1.4.1.164.6.1.12.2.6 | ||
| OBJECT IDENTIFIER | |||
| radAce2002E | 1.3.6.1.4.1.164.6.1.12.2.7 | ||
| OBJECT IDENTIFIER | |||
| radAce2E | 1.3.6.1.4.1.164.6.1.12.2.8 | ||
| OBJECT IDENTIFIER | |||
| radAce2T | 1.3.6.1.4.1.164.6.1.12.2.9 | ||
| OBJECT IDENTIFIER | |||
| radMlAtmE1 | 1.3.6.1.4.1.164.6.1.12.2.10 | ||
| OBJECT IDENTIFIER | |||
| radMlAtmT1 | 1.3.6.1.4.1.164.6.1.12.2.11 | ||
| OBJECT IDENTIFIER | |||
| radAmc102 | 1.3.6.1.4.1.164.6.1.12.2.12 | ||
| OBJECT IDENTIFIER | |||
| radAmc102c | 1.3.6.1.4.1.164.6.1.12.2.13 | ||
| OBJECT IDENTIFIER | |||
| radAce202 | 1.3.6.1.4.1.164.6.1.12.2.14 | ||
| OBJECT IDENTIFIER | |||
| radAce | 1.3.6.1.4.1.164.6.1.12.3 | ||
| OBJECT IDENTIFIER | |||
| radAce101 | 1.3.6.1.4.1.164.6.1.12.3.1 | ||
| OBJECT IDENTIFIER | |||
| radAce102 | 1.3.6.1.4.1.164.6.1.12.3.2 | ||
| OBJECT IDENTIFIER | |||
| radAce50 | 1.3.6.1.4.1.164.6.1.12.3.3 | ||
| OBJECT IDENTIFIER | |||
| radSysLA | 1.3.6.1.4.1.164.6.1.13 | ||
| OBJECT IDENTIFIER | |||
| radLA140 | 1.3.6.1.4.1.164.6.1.13.1 | ||
| OBJECT IDENTIFIER | |||
| radLA110 | 1.3.6.1.4.1.164.6.1.13.2 | ||
| OBJECT IDENTIFIER | |||
| radLA104 | 1.3.6.1.4.1.164.6.1.13.3 | ||
| OBJECT IDENTIFIER | |||
| radSysTerminal | 1.3.6.1.4.1.164.6.1.100 | ||
| OBJECT IDENTIFIER | |||
| agnt | 1.3.6.1.4.1.164.6.2 | ||
| OBJECT IDENTIFIER | |||
| agnHwVersion | 1.3.6.1.4.1.164.6.2.1 | ||
| ASCII string for description and display of the agent hardware version, as it is known by the agent software.The user can update the version upon request when he changes components in the agent's module | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| agnTrapMask | 1.3.6.1.4.1.164.6.2.2 | ||
| The value of this attribute determines the type of traps the agent should mask and not send to the management console. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnTrapValue | 1.3.6.1.4.1.164.6.2.3 | ||
| The value of the trap decoded in internal RAD format. Full description is given in the Trap definition file | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnChangeCnt | 1.3.6.1.4.1.164.6.2.4 | ||
| The number of changes in system configuration that were reported to the manager since last cold start | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| agnSpecific | 1.3.6.1.4.1.164.6.2.5 | ||
| Object identifier of entity containing additional information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| agnConfigMsg | 1.3.6.1.4.1.164.6.2.6 | ||
| Full configuration message coded in internal RAD application format. This entry describes agent's configuration. For MP-2200 R3, this object describes agent's support of the V5.1 feature: 1 octet ; bit 0 (LSB). '1' - V5.1 feature is supported '0' - V5.1 feature is not supported. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| mngTrapIpTable | 1.3.6.1.4.1.164.6.2.7 | ||
| This table indicates the destination address of the traps. Internally it will be limited to ten addresses. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| MngEntry | |||
| mngEntry | 1.3.6.1.4.1.164.6.2.7.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| MngEntry | |||
| mngID | 1.3.6.1.4.1.164.6.2.7.1.1 | ||
| This value indicates an index of a specific IP address | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| mngIP | 1.3.6.1.4.1.164.6.2.7.1.2 | ||
| This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| mngIPMask | 1.3.6.1.4.1.164.6.2.7.1.3 | ||
| This value indicates the mask of the destination addresses of the traps. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| mngTrapMask | 1.3.6.1.4.1.164.6.2.7.1.4 | ||
| The value of this attribute determines the type of traps the agent should mask and not send to this NMS. The value is differently determined for different products. There are mainly two methods: - an integer number, specifying the traps' severity. - a sum of 2**n, where n is a bit assigned to a certain masked trap group. User should consult the product specification, to find out the method employed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnIndication | 1.3.6.1.4.1.164.6.2.8 | ||
| Attribute describing the state of the entity the agent is responsible for. In case of a modular entity, the value of this attribute will be according to the component which is in the worst state. The order of severity (from top to bottom) is: critical-> major (or faulty)-> minor-> event-> warning-> normal (off). | |||
| OBJECT-TYPE | |||
| INTEGER | faulty(1), warning(2), normal(3), minor(4), major(5), event(6), critical(7) | ||
| agnMonitorModeCmd | 1.3.6.1.4.1.164.6.2.9 | ||
| Setting this attribute to ON, will enforce the agent to change its mode of operation to Monitor Mode | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| agnLed | 1.3.6.1.4.1.164.6.2.10 | ||
| This entry specifies the LEDs status of the agent module . Each led will be represented by 4 bits where the first 2 bits (left) will specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) will specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| trapTable | 1.3.6.1.4.1.164.6.2.11 | ||
| This table includes the last few traps generated by the agent, for future retrieval. The table has a limited capacity. If traps are not retrieved in proper time, they will be over-written by new traps | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| TrapEntry | |||
| trapEntry | 1.3.6.1.4.1.164.6.2.11.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| TrapEntry | |||
| trapID | 1.3.6.1.4.1.164.6.2.11.1.1 | ||
| This value indicates an index of a specific trap | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| trapVal | 1.3.6.1.4.1.164.6.2.11.1.2 | ||
| This value is the actual ASCII description of the trap. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| trapTimeSinceOccurrence | 1.3.6.1.4.1.164.6.2.11.1.3 | ||
| This value indicates the amount of time passed since the occurrence of the event that trigger this trap. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| fileTransfer | 1.3.6.1.4.1.164.6.2.12 | ||
| OBJECT IDENTIFIER | |||
| fileServerIP | 1.3.6.1.4.1.164.6.2.12.1 | ||
| The IP address of the server from which the file is loaded | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| fileName | 1.3.6.1.4.1.164.6.2.12.2 | ||
| The name of the file to be loaded. For protection, read returns NULL. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| fileTransCmd | 1.3.6.1.4.1.164.6.2.12.3 | ||
| The command to be executed on fileName at fileServerIP. | |||
| OBJECT-TYPE | |||
| INTEGER | swDwnLoad(1), configDwnLoad(2), configUpLoad(3), coProcDwnLoad(4), stateUpLoad(5), dwnLoadUserFile(6), upLoadUserFile(7), swDwnLoadAndReset(8), noOp(255) | ||
| tftpRetryTimeOut | 1.3.6.1.4.1.164.6.2.12.4 | ||
| General Retransmission time-out value (seconds) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| tftpTotalTimeOut | 1.3.6.1.4.1.164.6.2.12.5 | ||
| Total Retransmission time-out value (seconds) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| tftpStatus | 1.3.6.1.4.1.164.6.2.12.6 | ||
| Status of tftp session. When a session ended with success, the tftpStatus should be endedOk(6). Before restarting a tftp session, the NMS should set the tftpStatus to noOp(2). That's the reason of MAX-ACCESS read-write to this field. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(2), connecting(3), transferringData(4), endedTimeOut(5), endedOk(6), error(7) | ||
| tftpError | 1.3.6.1.4.1.164.6.2.12.7 | ||
| The MSB represents the standard error code. The LSB represents the private error code. 0x0000 is No Error 0x0100 is File Not Found 0x0400 is Illegal TFTP operation 0x0500 is Unknown transfer ID 0x0001 is Server Overflow 0x0002 is No empty UDP port 0x0003 is No empty connection 0x0004 is Illegal File Mode 0x0007 is Illegal PDU size | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(2) | ||
| fileTransferToSubSystems | 1.3.6.1.4.1.164.6.2.12.8 | ||
| This object represents the sub-systems the fileTransCmd refers to. It should be used when a system is divided to sub-systems and each sub-system (or part of them) can have a different SW/Configuration. Each bit of this object will represent one of the sub-systems. Bit='1' - APPLY to respective sub-system Bit='0' - DO NOT APPLY to respective sub-system For the meaning of each bit, see product's specification. User will select the sub-systems envolved by filling-in the bits that represent these sub-systems. In this case, the file represented by 'fileName' will include several parts, each representing one of the sub-systems. The agent will refer only to the part/s indicated by this object. 0 Octet Strings = not applicable DEFVAL = 0h for the products that support this object. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| fileNameWithinProduct | 1.3.6.1.4.1.164.6.2.12.9 | ||
| The file name used by the product within the product file system. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| intSwdlTable | 1.3.6.1.4.1.164.6.2.12.10 | ||
| This parameters table is for internal Software down load. It also includes data about all files contained in the Object from which down-load is performed. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| IntSwdlEntry | |||
| intSwdlEntry | 1.3.6.1.4.1.164.6.2.12.10.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| IntSwdlEntry | |||
| intSwdlObjIdx | 1.3.6.1.4.1.164.6.2.12.10.1.1 | ||
| The index of the object from which down-load is performed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| intSwdlFileIdx | 1.3.6.1.4.1.164.6.2.12.10.1.2 | ||
| The index of the files included in intSwdlObjIdx. One of these files can be selected to be internally downloaded. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| intSwdlFileName | 1.3.6.1.4.1.164.6.2.12.10.1.3 | ||
| The name of the file. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| intSwdlFileSwVer | 1.3.6.1.4.1.164.6.2.12.10.1.4 | ||
| The software version of the file. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| intSwdlSwDate | 1.3.6.1.4.1.164.6.2.12.10.1.5 | ||
| The software version date of the file. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| intSwdlSize | 1.3.6.1.4.1.164.6.2.12.10.1.6 | ||
| The size of the file. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| intSwdlCmd | 1.3.6.1.4.1.164.6.2.12.10.1.7 | ||
| The command to down-load a SW file to an object. The Agent will change the value of this MIB object to off(2) automatically, after accepting the command. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), on(3) | ||
| intSwdlToSubSystem | 1.3.6.1.4.1.164.6.2.12.10.1.8 | ||
| This object defines the subsystem for download. Bit='1'- APPLY to respective sub system. Bit='0'- DO NOT APPLY to respective sub system. For more details see product specification. For every octet bit0=LSB, bit7=MSB | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| swdlStatusTable | 1.3.6.1.4.1.164.6.2.12.11 | ||
| This parameters table is for software download status. It also includes data about the files down-loaded or attempted to be down-loaded. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SwdlStatusEntry | |||
| swdlStatusEntry | 1.3.6.1.4.1.164.6.2.12.11.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SwdlStatusEntry | |||
| swdlStatusTypeIdx | 1.3.6.1.4.1.164.6.2.12.11.1.1 | ||
| The index of the down-load type (e.g. external (1) or internal (2)). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| swdlStatusIdx | 1.3.6.1.4.1.164.6.2.12.11.1.2 | ||
| The index of the status rows. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| swdlStatusFileName | 1.3.6.1.4.1.164.6.2.12.11.1.3 | ||
| The name of the file. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swdlStatusSlot | 1.3.6.1.4.1.164.6.2.12.11.1.4 | ||
| The slot of the updated (or attempted to be updated) object. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swdlStatusSubSystem | 1.3.6.1.4.1.164.6.2.12.11.1.5 | ||
| The subsystem that updated (or attempted to be updated). | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| swdlStatusStatus | 1.3.6.1.4.1.164.6.2.12.11.1.6 | ||
| The status of the down load process. Value: Fail (2), OK (3), InProcess (4). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| swdlStatusTime | 1.3.6.1.4.1.164.6.2.12.11.1.7 | ||
| This MIB parameter indicates the time SW download was finished. The format shuld be YYYY-MM-DD, hh:mm:ss | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| clearDwldStatusLog | 1.3.6.1.4.1.164.6.2.12.12 | ||
| This object clears the status log. Value: off(2), external(3), internal(4) The Agent will change the value of this MIB object to off(2) automatically, after accepting the command . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| systemReset | 1.3.6.1.4.1.164.6.2.13 | ||
| Reset action to be performed on the system. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), resetConfig(4) | ||
| systemTiming | 1.3.6.1.4.1.164.6.2.14 | ||
| OBJECT IDENTIFIER | |||
| systemDate | 1.3.6.1.4.1.164.6.2.14.1 | ||
| System date. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| systemTime | 1.3.6.1.4.1.164.6.2.14.2 | ||
| System time. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| systemPort | 1.3.6.1.4.1.164.6.2.15 | ||
| OBJECT IDENTIFIER | |||
| physicalConnectorTable | 1.3.6.1.4.1.164.6.2.15.1 | ||
| This table includes the connector type of ports or interfaces. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PhysicalConnectorEntry | |||
| physicalConnectorEntry | 1.3.6.1.4.1.164.6.2.15.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PhysicalConnectorEntry | |||
| portIdx | 1.3.6.1.4.1.164.6.2.15.1.1.1 | ||
| This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| physicalConnector | 1.3.6.1.4.1.164.6.2.15.1.1.2 | ||
| The connector of the port/interface. other - none of the specified connectors none - no connector. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), v35(2), rs530(3), x21(4), bnc(5), utp(6), aui(7), rs422(8), crossUtp(9), rj45(10), v24(11), g703(12), termBlock3AndRj45(13), terminalBlock3(14), terminalBlock5(15), terminalBlock7(16), db25(17), db15(18), rj45ethernet(19), termBlock5AndRj45(20), db9(21), g703E1(22), g703E1-LTU(23), sc(24), st(25), stl(26), fc(27), tb5w(28), termBlock6AndRj45(29), ethBnc(30), scsi26(31), eth4381(32), twoBnc(33), scsi50(34), twoMiniBnc(35), sf1(36), terminalBlock4(37), sf2(38), db25Balanced(39), v36(40), block4W(41), iripRj45(42), irEthQRj45(43), iripBnc(44), rs530WA(45), v35WA(46), irEthQBnc(47), v35Db25(48), rj11(49), mtrj(50), lc(51), terminalBlock2(52), irEth10s100(53), scsi68(54), sf3(55), fcLH(56), none(255) | ||
| portOptWaveLength | 1.3.6.1.4.1.164.6.2.15.1.1.3 | ||
| Wave Length of an Optical interface/port in [nm] and specification if Laser LH,Laser or LED. notApplicable - for non-optical ports. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), nm850(2), nm1300(3), nm1300Laser(4), nm1550Laser(5), nm1300LaserLH(6), nm1550LaserLH(7) | ||
| portOptMode | 1.3.6.1.4.1.164.6.2.15.1.1.4 | ||
| Laser Mode of an Optical Laser interface/port. notApplicable - for non-Laser ports. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), singleMode(2), multiMode(3) | ||
| prtSupervisory | 1.3.6.1.4.1.164.6.2.15.2 | ||
| OBJECT IDENTIFIER | |||
| prtSpTable | 1.3.6.1.4.1.164.6.2.15.2.1 | ||
| A table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtSpEntry | |||
| prtSpEntry | 1.3.6.1.4.1.164.6.2.15.2.1.1 | ||
| Supervisory port parameter table. | |||
| OBJECT-TYPE | |||
| PrtSpEntry | |||
| prtSupervisoryIndex | 1.3.6.1.4.1.164.6.2.15.2.1.1.1 | ||
| The SP port index. The LS byte of the integer is the port index 1..255. The MS byte is different than 0 only if the port belongs to a module. In that case it is the module number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtSupervisoryRate | 1.3.6.1.4.1.164.6.2.15.2.1.1.2 | ||
| This attribute indicates the operation rate (speed) of the port. auto - automatic rate selection, by the agent. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(1), s300bps(2), s1200bps(3), s2400bps(4), s4800bps(5), s9600bps(6), s19200bps(7), s38400bps(8), s57600bps(9), s115200bps(10) | ||
| prtSupervisoryDataBits | 1.3.6.1.4.1.164.6.2.15.2.1.1.3 | ||
| This attribute indicates the number of data bits in an async frame | |||
| OBJECT-TYPE | |||
| INTEGER | dataBits7(1), dataBits8(2) | ||
| prtSupervisoryParity | 1.3.6.1.4.1.164.6.2.15.2.1.1.4 | ||
| This attribute indicates the parity mode in an async frame | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), odd(2), even(3) | ||
| prtSupervisoryStopBits | 1.3.6.1.4.1.164.6.2.15.2.1.1.5 | ||
| This attribute indicates the parity mode in an async frame. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), stopBits1(2), stopBits1dot5(3), stopBits2(4) | ||
| prtSupervisoryUsage | 1.3.6.1.4.1.164.6.2.15.2.1.1.6 | ||
| This attribute indicates the usage of the SP port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), noUse(2), terminal(3), nmsSlip(4), nmsPpp(5), muxSlip(6), muxPpp(7), dialOut(8) | ||
| prtSupervisoryInterface | 1.3.6.1.4.1.164.6.2.15.2.1.1.7 | ||
| This attribute indicates the supervisory port interface. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), dce(2), dte(3) | ||
| prtSupervisoryCTS | 1.3.6.1.4.1.164.6.2.15.2.1.1.8 | ||
| CTS line state. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), rts(3), dteWait(4), dteIgnore(5) | ||
| prtSupervisoryDcdDelay | 1.3.6.1.4.1.164.6.2.15.2.1.1.9 | ||
| DCD delay in msec. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), d0(2), d10(3), d50(4), d100(5), d200(6), d300(7) | ||
| prtSupervisoryDSR | 1.3.6.1.4.1.164.6.2.15.2.1.1.10 | ||
| DSR line state. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), on(2), dtr(3) | ||
| prtSupervisoryRoutProtocol | 1.3.6.1.4.1.164.6.2.15.2.1.1.11 | ||
| This attribute indicates the routing protocol of the port. notApplicable - for DP. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), none(2), proprietary(3), rip2(4) | ||
| prtPerformance | 1.3.6.1.4.1.164.6.2.15.3 | ||
| OBJECT IDENTIFIER | |||
| prtPerfTable | 1.3.6.1.4.1.164.6.2.15.3.1 | ||
| This table includes G.826 ports or interfaces. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtPerfEntry | |||
| prtPerfEntry | 1.3.6.1.4.1.164.6.2.15.3.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtPerfEntry | |||
| prtPerfIdx | 1.3.6.1.4.1.164.6.2.15.3.1.1.1 | ||
| This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfPeriodRef | 1.3.6.1.4.1.164.6.2.15.3.1.1.2 | ||
| This object is an index that specifies which period of time, the next 5 objects refer to. currentPeriod - the period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. lastPeriod - the period between last two commands of prtPerfSaveAndResetCmd. - If only one command occured since Start-up: the period between Start-up and last command. - If no command occured since Start-up: this period will not actually exist. In this case, he following 5 objects will be 0. | |||
| OBJECT-TYPE | |||
| INTEGER | currentPeriod(1), lastPeriod(2) | ||
| prtPerfElapsedTime | 1.3.6.1.4.1.164.6.2.15.3.1.1.3 | ||
| Elapsed Time in seconds. - for prtPerfPeriodRef=currentPeriod: The period since last prtPerfSaveAndResetCmd received or since Start-up (if no prtPerfSaveAndResetCmd was received since Start-up) until now. - for prtPerfPeriodRef=lastPeriod: The value of prtPerfElapsedTime when last prtPerfSaveAndResetCmd was received. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfUAS | 1.3.6.1.4.1.164.6.2.15.3.1.1.4 | ||
| Number of Unavailable Seconds for the reference period (prtPerfPeriodRef). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfES | 1.3.6.1.4.1.164.6.2.15.3.1.1.5 | ||
| Number of Errored Seconds for the reference period (prtPerfPeriodRef). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfSES | 1.3.6.1.4.1.164.6.2.15.3.1.1.6 | ||
| Number of Severely Errored Seconds for the reference period (prtPerfPeriodRef). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfBBE | 1.3.6.1.4.1.164.6.2.15.3.1.1.7 | ||
| Number of Background Block (or Frame) Errors for the reference period (prtPerfPeriodRef). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfBlocksPerSec | 1.3.6.1.4.1.164.6.2.15.3.1.1.8 | ||
| Blocks per second (or frames per second) of the port/interface indicated by portIdx. This object is constant for a certain port/interface. It is not affected by the prtPerfPeriodRef index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtPerfTimeTag | 1.3.6.1.4.1.164.6.2.15.3.1.1.9 | ||
| Time Tag of Last Period: sysUpTime when last prtPerfSaveAndResetCmd was executed. This object is applicable only for prtPerfPeriodRef=lastPeriod. For prtPerfPeriodRef=currentPeriod, the value will always be 0. | |||
| OBJECT-TYPE | |||
| TimeTicks | |||
| prtPerfSaveAndResetCmd | 1.3.6.1.4.1.164.6.2.15.3.1.1.10 | ||
| A command per port/interface, to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. This object is applicable only for prtPerfPeriodRef=currentPeriod. Setting this object to on(3) for prtPerfPeriodRef=last, will cause the agent to return: Bad Value response. When setting validly this object to on(3), agent will perform the required command and will reset automatically the value of this object to off(2). Setting this object to off(2), will do nothing. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtTest | 1.3.6.1.4.1.164.6.2.15.4 | ||
| OBJECT IDENTIFIER | |||
| prtTestTable | 1.3.6.1.4.1.164.6.2.15.4.1 | ||
| This table includes test data for ports or interfaces. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtTestEntry | |||
| prtTestEntry | 1.3.6.1.4.1.164.6.2.15.4.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtTestEntry | |||
| prtTestIdx | 1.3.6.1.4.1.164.6.2.15.4.1.1.1 | ||
| This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTestCmdAndStatus | 1.3.6.1.4.1.164.6.2.15.4.1.1.2 | ||
| Setting this object to a value as detailed further on (except 0) will initiate a test on the specific port. The test/s requested will be set according to the respective bit. The value of this object will be a sum of (2**n), where n is the Bit: TEST BIT VALUE ----------- --- ------ reserved 0 1 PayloadLoop=RLB 1 (=Remote Loopback) 2 LineLoop=DIG 2 (=Digital) 4 OtherLoop 3 8 InwardLoop=LLB 4 (=Local Loopback) 16 BERT 5 32 LC 6 64 ToneInjection 7 128 Inband 8 256 e.g : If the requested value is 20 -> 010100 -> Bits 2 & 4 are set -> the requested tests are : LineLoopback=DIG InwardLoopback=LLB Not all tests combinations are valid. For valid test combination, see each product's specification. For LRS52, only single test is allowed simultaneously The terminology and order of the first tests (except BERT) is according to the one used for Test Status of DS1 and DS3 standards. The notations : RLB, LLB, DIG are the most used in RAD's products, but they can be different. For exact definition see product's spec. Setting this object to stop (value=0 ; all bits are 0), will stop all the user requested tests running on the selected port. When no test is running on the port, the Get value (test status) will be 0. PayloadLoop=RLB The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. LineLoop=DIG The received signal at this interface does not go through the device (minimum penetration) but is looped back out. OtherLoop Loopbacks that are not defined here. InwardLoop=LLB The sent signal at this interface is looped back through the device. LC This loop is applicable only for HSSI interface, towards the router . ToneInjection This loop is applicable for analog voice (like FXS). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBertCounter | 1.3.6.1.4.1.164.6.2.15.4.1.1.3 | ||
| This object indicates the number of BERT errors encountered during the BERT operation. It is valid only when BERT (Bit Error Rate Test) is active on the specific port. The Counter starts from zero (0) anytime BERT is initiated. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtTestInitiator | 1.3.6.1.4.1.164.6.2.15.4.1.1.4 | ||
| This object indicates who initiated this port's test/s. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), user(2), remoteUnit(3), dteRouter(4) | ||
| prtTestTimeout | 1.3.6.1.4.1.164.6.2.15.4.1.1.5 | ||
| This object is applicable only when a single test is running. It indicates the test activation timeout in minutes. When the timeout expires, the test is stopped. Value of 0 indicates test may run Forever | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| prtParam | 1.3.6.1.4.1.164.6.2.15.5 | ||
| OBJECT IDENTIFIER | |||
| prtParamTable | 1.3.6.1.4.1.164.6.2.15.5.1 | ||
| This table includes general port parameters. The meaning is different for every product that supports it due to a general parameter - prtControlCnfg. For ACE2002: This table is used as a mechanism to create the next interface index. The algorithm description: The NMS will send the agent the following get command: get(nextIfIndex.index), where index=interface on which the new index is dependent on. Upon this command the agent will generate and return the new index to the NMS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtParamEntry | |||
| prtParamEntry | 1.3.6.1.4.1.164.6.2.15.5.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtParamEntry | |||
| prtParamIdx | 1.3.6.1.4.1.164.6.2.15.5.1.1.1 | ||
| This object is an index of the specific port or interface. For a port, the index will be as agreed between agent and application. For an interface, ifIndex may be used. For ACE2002: This parameter is the physical layer ifIndex of the slot on which the NMS requires the next interface index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtControlCnfg | 1.3.6.1.4.1.164.6.2.15.5.1.1.2 | ||
| This object may be used for port RW general parameter/s. For detailed meaning, see product's spec. Supported by: PRBi-E3/T3. For ACE2002: This parameter will include the value of the new index generated by agent. For Optimux-T3: This parameter will be used for Release Remote LLB Command: on=2= Set value only. Command to release LLB of Remote Unit. Agent will return automatically to 'off' value after performing the command. off=3=Get value only. For LA140 This parameter will be used as EchoCanceler per timeslot off = 2 Echo Canceler is disabled on = 3 Echo Canceler is enabled | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtParamClkSrc | 1.3.6.1.4.1.164.6.2.15.5.1.1.3 | ||
| The source of Transmit Clock. 'loopTiming' or 'loopback' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' or 'internal' indicates that a local clock source is used or when an external clock is attached to the box containing the interface. 'throughTiming' or 'external' indicates that recovered receive clock from another card or interface is used as the transmit clock. 'adaptive' indicates that the clock is recovered according to the received data flow rate. | |||
| OBJECT-TYPE | |||
| INTEGER | loopTiming(1), localTiming(2), throughTiming(3), adaptive(4), notApplicable(255) | ||
| prtParamPhantom | 1.3.6.1.4.1.164.6.2.15.5.1.1.4 | ||
| Power feeding to another device. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| prtParamResetStatsCmd | 1.3.6.1.4.1.164.6.2.15.5.1.1.5 | ||
| Reset statistics of the selected port. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| prtParamLastResetStatsTime | 1.3.6.1.4.1.164.6.2.15.5.1.1.6 | ||
| The value of MIB II's sysUpTime object at the last time that prtParamResetStatsCmd was Set to on(3) for this port. If prtParamResetStatsCmd was never Set to on(3) since last re-initialization of the agent, then this object contains a zero value. This object enables calculating the running time of Statistics counters for this port, by: [sysUpTime-prtParamLastResetStatsTime]. | |||
| OBJECT-TYPE | |||
| TimeStamp | |||
| prtIP | 1.3.6.1.4.1.164.6.2.15.6 | ||
| OBJECT IDENTIFIER | |||
| prtIpParamTable | 1.3.6.1.4.1.164.6.2.15.6.1 | ||
| A table - Parameters for IP Ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtIpParamEntry | |||
| prtIpParamEntry | 1.3.6.1.4.1.164.6.2.15.6.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| PrtIpParamEntry | |||
| prtIpParamConfigIdx | 1.3.6.1.4.1.164.6.2.15.6.1.1.1 | ||
| This object indicates the Configuration number (1..255) referred. Value of 255 specifies the TmpCnfg (Scratch). For products having Agent and Edit configurations, Write operation for the table entries is allowed only to Config=255. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIpParamSlotIdx | 1.3.6.1.4.1.164.6.2.15.6.1.1.2 | ||
| This object indicates a unique number of the slot position in which the module is inserted. notApplicable = 255 (for products that don't have slots). For KM: kmxMlA (103), kmxMlB (104). | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIpParamIdx | 1.3.6.1.4.1.164.6.2.15.6.1.1.3 | ||
| This object indicates a unique Port Index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIpParamHostIP | 1.3.6.1.4.1.164.6.2.15.6.1.1.4 | ||
| The host interface IP address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| prtIpParamHostMask | 1.3.6.1.4.1.164.6.2.15.6.1.1.5 | ||
| The host interface subnet mask. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| prtIpParamDefaultGateway | 1.3.6.1.4.1.164.6.2.15.6.1.1.6 | ||
| Default Gateway's IP Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| prtIpParamMediaMode | 1.3.6.1.4.1.164.6.2.15.6.1.1.7 | ||
| This object indicates the real Media Mode. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), halfDuplex(2), fullDuplex(3) | ||
| prtIpParamMediaRate | 1.3.6.1.4.1.164.6.2.15.6.1.1.8 | ||
| This object indicates the real Media Rate (Mbps). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), r10Mbps(2), r100Mbps(3) | ||
| prtIpParamMngVlanSupport | 1.3.6.1.4.1.164.6.2.15.6.1.1.9 | ||
| Management VLAN support (Tagging). no - No support of VLAN Tagging. yes - 4 VLAN bytes will be added to the frame. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), no(2), yes(3) | ||
| prtIpParamMngVlanId | 1.3.6.1.4.1.164.6.2.15.6.1.1.10 | ||
| Management VLAN ID. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIpParamMngVlanPriority | 1.3.6.1.4.1.164.6.2.15.6.1.1.11 | ||
| Management VLAN Frame priority. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtIpParamRingMode | 1.3.6.1.4.1.164.6.2.15.6.1.1.12 | ||
| This object indicates If Ring Mode is enabled or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| systemResetAllStatsCmd | 1.3.6.1.4.1.164.6.2.16 | ||
| Reset statistics of all ports and connections of the device. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| systemClearTablesCmd | 1.3.6.1.4.1.164.6.2.17 | ||
| tempCnfgTables - Set *RowStatus = destroy for all entries of some tables having *RowStatus object, for temporary configuration only! (255). For the relevant tables, see product's specification. This object should be used by WAN product applications before performing the Update operation, in order to clear old entries of these tables. off - agent will automatically change to this value, after performing the command. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), tempCnfgTables(3) | ||
| systemParameter | 1.3.6.1.4.1.164.6.2.18 | ||
| This parameter can be used for different purposes: - TELNET session time-out in seconds. - Ace20: when trying to create row in a table that already has row with the same values, if set of values has to be unique in table, this attribute is set to the index of the existing row. - Optimux-T3: when CH interfaces are RJ-45, user can select via this object, the interface type for each Group of channels: T1 or E1: The selection will be a sum of the following Bits. '0' = T1 '1' = E1 Bit Group Value for each Bit having '1' 1 1 (CH-1..CH-8) 1 2 2 (CH-9..CH-12) 2 3 3 (CH-13..CH-20) 4 4 4 (CH-21..CH-28) 8 Examples: 15 = all Groups are selected to be E1 6 = Group 2 and Group 3 are selected to be E1 (Group 1 and Group 4 are T1). - FCD-A, FCD-M: user can select via this object the configuration used for Get values of MSDSL parameters that don't have configuration index. 1 =active configuration 255=temporary configuration. Set of this object should be done before Getting the MSDSL RW parameters. - Ace2002: This parameter indicates the number of intervals that were successfully uploaded upon statistics collection session. - FCD-IP, WR, FCD-IPD, LA-240: This parameter indicates whether Telnet Access is enabled/disabled: Values: 2 - Telnet Access is Disabled. 3 - Telnet Access is Enabled. - Vmux-110: This parameter value equals maximum number of bundles. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| agnGlobalAlarmMask | 1.3.6.1.4.1.164.6.2.19 | ||
| The value of this attribute determines the alarm traps the agent should mask and not send to the managers. Each bit from a certain octet represents a certain alarm. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| alarmSeverity | 1.3.6.1.4.1.164.6.2.20 | ||
| This object specifies the severity of the alarms. | |||
| OBJECT-TYPE | |||
| INTEGER | event(3), minor(4), major(5), warning(6), critical(7) | ||
| alarmState | 1.3.6.1.4.1.164.6.2.21 | ||
| . | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| agnTestStatus | 1.3.6.1.4.1.164.6.2.22 | ||
| Indicates the current test status (for all levels: system, card, port). This attribute will be set to: on(3): when there is at least one test in progress on the system/card/port off(2): when there is NO test in progress on the system/card/port | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| systemSaveAndResetAllStatsCmd | 1.3.6.1.4.1.164.6.2.23 | ||
| on - a command to Save data of Current Period in Last Period data-set and start a new counting period for Current Period. off - agent will automatically change to this value, after performing the command. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| systemDefaultGateway | 1.3.6.1.4.1.164.6.2.24 | ||
| Default Gateway's IP Address. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| systemPsTable | 1.3.6.1.4.1.164.6.2.25 | ||
| This table describes the PS types of a device. Usage of this table is specified in the device's NMS SRS | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| SystemPsEntry | |||
| systemPsEntry | 1.3.6.1.4.1.164.6.2.25.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| SystemPsEntry | |||
| systemPsIndex1 | 1.3.6.1.4.1.164.6.2.25.1.1 | ||
| First Index. In HUBs: 1 = PS-A slot 2 = PS-B slot. In SA units: 1 = PS1 2 = PS2 Default = 1 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| systemPsIndex2 | 1.3.6.1.4.1.164.6.2.25.1.2 | ||
| Second Index. In HUBs: 1 always. In SA units: 1 = Local 2 = Remote Default = 1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| systemPsType | 1.3.6.1.4.1.164.6.2.25.1.3 | ||
| The type of PS, for a stand-alone product. acDc - AC with rj45 DC. acPF - Power Feeding (phantom) box that is feeding another box by external AC. dcPF - Power Feeding (phantom) box that is feeding another box by external DC. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), ac(2), dc(3), acDc(4), acPF(5), dcPF(6) | ||
| systemPsStatus | 1.3.6.1.4.1.164.6.2.25.1.4 | ||
| The Status of the PS unit. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), failed(2), ok(3) | ||
| systemPsHotSwap | 1.3.6.1.4.1.164.6.2.25.1.5 | ||
| Is PS unit hot swap or fixed. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), fixed(2), hotSwap(3) | ||
| agnFans | 1.3.6.1.4.1.164.6.2.26 | ||
| This entry specifies the FANs existence and status. Each fan will be represented by 2 bits, where the first bit (right) will specify the existence: (0= Not exist, 1=exist), and the left bit will specify it's status (0= OK, 1=FAIL), so for each fan: 00 - FAN does not exist 01 - FAN exists and OK 11 - FAN exists and is Failed bits 0-1 are for first fan bits 2-3 are for 2nd fan (if exists). | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnSendTrapParameter | 1.3.6.1.4.1.164.6.2.27 | ||
| This object specifies if the agent will attach a specific parameter to a trap. For ACE2002 the agent will attach or not the openViewSeverity parameter according to the value of this parameter: 1 - will attach openViewSeverity. 0 - will not attach openViewSeverity. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcIndexNext | 1.3.6.1.4.1.164.6.2.30 | ||
| This object contains an appropriate value to be used for xcIndex when creating entries in the xcTable. The value 0 indicates that no unassigned entries are available. To obtain the xcIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| xcTable | 1.3.6.1.4.1.164.6.2.31 | ||
| Configuration of system cross-connect entries. The table follows the behavior described in RFC 2515, RFC 1604 regarding the creation deletion and modification of an entry within the table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| XcEntry | |||
| xcEntry | 1.3.6.1.4.1.164.6.2.31.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| XcEntry | |||
| xcIndex | 1.3.6.1.4.1.164.6.2.31.1.1 | ||
| Cross Connect Identifier. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcIfIndex1 | 1.3.6.1.4.1.164.6.2.31.1.2 | ||
| The interface Index from the ifTable, which identify one side of the connection. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcVpi | 1.3.6.1.4.1.164.6.2.31.1.3 | ||
| The VPI of the ATM End-Point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcVci | 1.3.6.1.4.1.164.6.2.31.1.4 | ||
| The VCI of the ATM End-Point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcIfIndex2 | 1.3.6.1.4.1.164.6.2.31.1.5 | ||
| The interface Index from the ifTable, which identifies the other side of the connection. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| xcRowStatus | 1.3.6.1.4.1.164.6.2.31.1.6 | ||
| This parameter allows NMS to create/delete entries of this table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| xcDescr | 1.3.6.1.4.1.164.6.2.31.1.7 | ||
| A textual string containing information about the xc entry. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| xcAdminStatus | 1.3.6.1.4.1.164.6.2.31.1.8 | ||
| The desired administrative status of this bi-directional cross-connect. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2) | ||
| xcOperStatus | 1.3.6.1.4.1.164.6.2.31.1.9 | ||
| The operational status of this bi-directional cross-connect. | |||
| OBJECT-TYPE | |||
| INTEGER | up(1), down(2), unknown(3) | ||
| systemModule | 1.3.6.1.4.1.164.6.2.32 | ||
| OBJECT IDENTIFIER | |||
| modlParam | 1.3.6.1.4.1.164.6.2.32.1 | ||
| OBJECT IDENTIFIER | |||
| modlParamTable | 1.3.6.1.4.1.164.6.2.32.1.1 | ||
| This table include parameters for system modules. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| ModlParamEntry | |||
| modlParamEntry | 1.3.6.1.4.1.164.6.2.32.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| ModlParamEntry | |||
| modlParamIndex | 1.3.6.1.4.1.164.6.2.32.1.1.1.1 | ||
| The module index. The index can be the slot number or any other module index as described in the specifications of the device. For Vmux-2100 device, the index will have values of: 1..4 for slots 1..4. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| modlParamReset | 1.3.6.1.4.1.164.6.2.32.1.1.1.2 | ||
| Reset action to be performed on the module. Set the parameter will be done always to on(3) or factory (4). After performing the Reset operation, Agent will automatically set the parameter to off(2). | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3), factory(4) | ||
| modlParamSwdlStatus | 1.3.6.1.4.1.164.6.2.32.1.1.1.3 | ||
| This parameter indicates whatever the swdl is in process or not. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), off(2), inProcess(3) | ||
| modlParamLeds | 1.3.6.1.4.1.164.6.2.32.1.1.1.4 | ||
| This entry specifies the LEDs status of the module. Each led is represented by 4 bits where the first 2 bits (left) specify the status : (00=NA, 01=OFF, 10=ON, 11=BLINK), and the next two bits (right) specify the color : (00=GREEN, 01=RED, 10=YELLOW, 11=GRAY). The order of the LEDS is from top to bottom, left to right: For each row starting from the top, the LEDS are returned from left to right. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| agnNearFarConnection | 1.3.6.1.4.1.164.6.2.33 | ||
| This parameter describes the connection between near-end and far-end agents. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disconnected(2), connected(3) | ||
| agnAccess | 1.3.6.1.4.1.164.6.2.34 | ||
| OBJECT IDENTIFIER | |||
| agnTelnetAccess | 1.3.6.1.4.1.164.6.2.34.1 | ||
| Enable/Disable accessing the device via Telnet. disable - no one will be allowed to access the device via Telnet. enable - all users are allowed Telnet Access. managersOnly - Only manager stations listed in the manager's list are allowed. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3), managersOnly(4) | ||
| radStkHub | 1.3.6.1.4.1.164.7 | ||
| OBJECT IDENTIFIER | |||
| radStkHubEvents | 1.3.6.1.4.1.164.7.0 | ||
| The events for Rad Stackable General products. | |||
| OBJECT-IDENTITY | |||
| portStatusChanged | 1.3.6.1.4.1.164.7.0.26 | ||
| This trap is sent each time port status was changed. | |||
| NOTIFICATION-TYPE | |||
| stkHubETMdlLed | |||
| rpMauMediaAvailable | |||
| rptrPortOperStatus | |||
| softErrors | 1.3.6.1.4.1.164.7.0.33 | ||
| This trap is sent when the software errors threshold is exceeded. | |||
| NOTIFICATION-TYPE | |||
| stkHubGen | 1.3.6.1.4.1.164.7.1 | ||
| OBJECT IDENTIFIER | |||
| stkHubGenAgn | 1.3.6.1.4.1.164.7.1.1 | ||
| OBJECT IDENTIFIER | |||
| stkHubAgentResetConfig | 1.3.6.1.4.1.164.7.1.1.1 | ||
| Setting the value to ON(3)is interpreted as a reset command for the agent NV Ram. When reset process is ended, a trap will be issued. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| stkHubAgentSpecific | 1.3.6.1.4.1.164.7.1.1.2 | ||
| Object identifier of entity containing additional information regarding this instance. | |||
| OBJECT-TYPE | |||
| OBJECT IDENTIFIER | |||
| stkHubSecurityTable | 1.3.6.1.4.1.164.7.1.2 | ||
| Hub's Security parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| StkHubSecurityEntry | |||
| stkHubSecurityEntry | 1.3.6.1.4.1.164.7.1.2.1 | ||
| An entry in table stkHubSecurityTable. | |||
| OBJECT-TYPE | |||
| StkHubSecurityEntry | |||
| stkHubSecID | 1.3.6.1.4.1.164.7.1.2.1.1 | ||
| Segment's security unique identification number | |||
| OBJECT-TYPE | |||
| Integer32 | 1..3 | ||
| stkHubSecEnable | 1.3.6.1.4.1.164.7.1.2.1.2 | ||
| This entry indicates whether the specific segment's security is active or not | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| stkHubSecurityPattern | 1.3.6.1.4.1.164.7.1.2.1.3 | ||
| A six-octet(48 bit) pattern: where the masked bits of stkHubSecurityMask need to match the MAC address of each port within the segment.Value of all zeros indicates no security. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubSecurityMask | 1.3.6.1.4.1.164.7.1.2.1.4 | ||
| Mask of the allowed MAC address that can be connected through the ports within the segment | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubPrtSecurityTable | 1.3.6.1.4.1.164.7.1.3 | ||
| Port Security parameters. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| StkHubPrtSecurityEntry | |||
| stkHubPrtSecurityEntry | 1.3.6.1.4.1.164.7.1.3.1 | ||
| An entry in table stkHubPrtSecurityTable. | |||
| OBJECT-TYPE | |||
| StkHubPrtSecurityEntry | |||
| stkHubModuleID | 1.3.6.1.4.1.164.7.1.3.1.1 | ||
| A unique identifier of the module(slot no.)this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubPrtID | 1.3.6.1.4.1.164.7.1.3.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubPrtSecID | 1.3.6.1.4.1.164.7.1.3.1.3 | ||
| A unique identifier of the security of a given port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubPrtSecurityEnable | 1.3.6.1.4.1.164.7.1.3.1.4 | ||
| The value of this attribute determines application of the port security. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| stkHubPrtSecurityPattern | 1.3.6.1.4.1.164.7.1.3.1.5 | ||
| A six-octet(48 bit) pattern: where the masked bits of stkHubPortSecurityMask need to match the MAC address. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubPrtSecurityMask | 1.3.6.1.4.1.164.7.1.3.1.6 | ||
| Mask of the allowed MAC address that can be connected through this port. The security of the individual port over writes the security of the segment where the port belongs to | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubTR | 1.3.6.1.4.1.164.7.2 | ||
| OBJECT IDENTIFIER | |||
| stkHubTREvents | 1.3.6.1.4.1.164.7.2.0 | ||
| The events for Stackable Token Ring. | |||
| OBJECT-IDENTITY | |||
| mdlStatusChanged | 1.3.6.1.4.1.164.7.2.0.27 | ||
| This trap is sent each time module status was changed.When a module is disconnected, the stkHubTRMdlLed status will be 00 (no led) and the stkHubTRMdlType will be empty(255). | |||
| NOTIFICATION-TYPE | |||
| stkHubTRMdlLed | |||
| stkHubTRMdlType | |||
| macAddressUpdated | 1.3.6.1.4.1.164.7.2.0.91 | ||
| This trap will be sent upon every change of MACAddress on a port. | |||
| NOTIFICATION-TYPE | |||
| stkHubTRPrtMACAddress | |||
| stkHubTRRing | 1.3.6.1.4.1.164.7.2.1 | ||
| OBJECT IDENTIFIER | |||
| stkHubTRRingCorrelationEnable | 1.3.6.1.4.1.164.7.2.1.1 | ||
| When set to ON(3), the in-band agent should perform correlation each time a station enters/leaves the segment. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| stkHubTRRingAutorecEnable | 1.3.6.1.4.1.164.7.2.1.2 | ||
| When set to ON(3), the in-band agent should perform autorecovery each time a beacon status is detected. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| stkHubTRRingAutorecResult | 1.3.6.1.4.1.164.7.2.1.3 | ||
| When autorecovery is completed the result will be recorded. While in process, STARTED will be recorded.Before process, NOT STARTED will be recorded | |||
| OBJECT-TYPE | |||
| INTEGER | not-started(1), started(2), segment-ok(3), segment-fixed(4), segment-closed(5), failed(6) | ||
| stkHubTRRingResetStatistics | 1.3.6.1.4.1.164.7.2.1.4 | ||
| Setting the value of this attribute to ON(3) resets all the inband statistics and error counters. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| stkHubTRRingLineErrCnt | 1.3.6.1.4.1.164.7.2.1.5 | ||
| This counter is incremented when a frame or token is copied or repeated by any of the stations on the ring, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between the SD and the ED of the frame or token, or 2) there is an FCS error in the frame. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingBurstErrCnt | 1.3.6.1.4.1.164.7.2.1.6 | ||
| This counter is incremented when any of the stations on the ring detects the absence of transitions for five half-bit timers (burst-five error). | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingACFCErrCnt | 1.3.6.1.4.1.164.7.2.1.7 | ||
| This counter is incremented when any of the stations on the ring receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame. It denotes a station that cannot set the AC bits properly. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingTotErrCnt | 1.3.6.1.4.1.164.7.2.1.8 | ||
| The total of the above described errors | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingTotErrThreshold | 1.3.6.1.4.1.164.7.2.1.9 | ||
| The Total Errors Threshold value. A trap indicating Soft Error will be sent, if the total number of errors during the last 10 seconds, reached the threshold value. Threshold value = 0 , disables this trap. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubTRRingTotalFrames | 1.3.6.1.4.1.164.7.2.1.10 | ||
| The total frames of the Ring. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingTotalFramesRate | 1.3.6.1.4.1.164.7.2.1.11 | ||
| The rate of total frames on the Ring. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubTRRingTotalOctets | 1.3.6.1.4.1.164.7.2.1.12 | ||
| The total octets of the Ring. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| stkHubTRRingOctetsRatio | 1.3.6.1.4.1.164.7.2.1.13 | ||
| Current traffic for the last time interval. The traffic is expressed in percents of the maximum TokenRing traffic . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubTRMdl | 1.3.6.1.4.1.164.7.2.2 | ||
| OBJECT IDENTIFIER | |||
| stkHubTRMdlTable | 1.3.6.1.4.1.164.7.2.2.1 | ||
| Bridge Hub Module table for TR media type Contains general information about the Module | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| StkHubTRMdlEntry | |||
| stkHubTRMdlEntry | 1.3.6.1.4.1.164.7.2.2.1.1 | ||
| An entry in table stkHubTRMdlTable. | |||
| OBJECT-TYPE | |||
| StkHubTRMdlEntry | |||
| stkHubTRMdlID | 1.3.6.1.4.1.164.7.2.2.1.1.1 | ||
| A unique identifier of the module in stack. Internal module identifier is always 1 | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| stkHubTRMdlType | 1.3.6.1.4.1.164.7.2.2.1.1.2 | ||
| Indicates the type of the module connected with specific identifier | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), sah16int(2), sah16ext(3), empty(255) | ||
| stkHubTRMdlReset | 1.3.6.1.4.1.164.7.2.2.1.1.3 | ||
| When this object is set to the value of ON(3), the module performs software reset. Upon completion, a trap will be issued to the management station and the value will be set to OFF. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| stkHubTRMdlLed | 1.3.6.1.4.1.164.7.2.2.1.1.4 | ||
| This entry specifies the LEDs status in the module . Each led will be represented by 4 bits where the first 2 bits will specify the status (NA, OFF, ON, BLINK), and the next two bits will specify the color (RED, GREEN, YELLOW) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubTRMdlSpeed | 1.3.6.1.4.1.164.7.2.2.1.1.5 | ||
| Attribute describing the bandwidth of the media as set by the module switch. For certain products, if the value of stkHubTRMdlMngState is 'enabled', then stkHubTRMdlSpeed can be set to the desired value. Else, it will be read-only, and will show the status of the jumper set of the main module. Refer product's manual. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), fourMegabit(2), sixteenMegabit(3) | ||
| stkHubTRMdlMngState | 1.3.6.1.4.1.164.7.2.2.1.1.6 | ||
| This object indicates the status of the Manage switch as set on the back panel of the main module. 'enabled' - means that management can override setting of some HW switch/es. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disabled(2), enabled(3) | ||
| stkHubTRMdlAutodisable | 1.3.6.1.4.1.164.7.2.2.1.1.7 | ||
| Attribute describing the status of port Autodisable mechanism, that protects against inserting in Token Ring adapters at the wrong speed. For certain products, if the value of stkHubTRMdlMngState is 'enabled', then stkHubTRMdlAutodisable can be set to the desired value. Else, it will be read-only, and will show the status of the jumper set of the main module. Refer product's manual. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| stkHubTRMdlConfigMsg | 1.3.6.1.4.1.164.7.2.2.1.1.8 | ||
| Full configuration message coded in internal RND application format. This entry describes module' configuration. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubTRPrt | 1.3.6.1.4.1.164.7.2.3 | ||
| OBJECT IDENTIFIER | |||
| stkHubTRPrtTable | 1.3.6.1.4.1.164.7.2.3.1 | ||
| Bridge Hub port table for TR media type Contains general information about the ports. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| StkHubTRPrtEntry | |||
| stkHubTRPrtEntry | 1.3.6.1.4.1.164.7.2.3.1.1 | ||
| An entry in table stkHubTRPrtTable. | |||
| OBJECT-TYPE | |||
| StkHubTRPrtEntry | |||
| stkHubTRPrtMdlID | 1.3.6.1.4.1.164.7.2.3.1.1.1 | ||
| A unique identifier of the module this port is attached to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubTRPrtID | 1.3.6.1.4.1.164.7.2.3.1.1.2 | ||
| A unique identifier of the port within its module. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| stkHubTRPrtFunctionality | 1.3.6.1.4.1.164.7.2.3.1.1.3 | ||
| Describes the functionality of the port in a Token ring topology | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), ringin(2), ringout(3), satellite(4), lobe(5) | ||
| stkHubTRPrtConnectorType | 1.3.6.1.4.1.164.7.2.3.1.1.4 | ||
| Type of hardware connector in the port. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), idc(2), rj45(3), srJ45(4), db9(5), bnc(6), fo-st(7), db25(8) | ||
| stkHubTRPrtAdminCmd | 1.3.6.1.4.1.164.7.2.3.1.1.5 | ||
| By setting this attribute to DISABLE(2) or SHORT(4) the management station can force this lobe/port-connection to be removed and block any access to the network via this lobe/port. It is not mandatory that a certain lobe/port will support all the enumerated states. The state of the lobe/port is type specific and indicated within the specific group | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disable(2), enable(3), short(4), normal(5) | ||
| stkHubTRPrtActiveState | 1.3.6.1.4.1.164.7.2.3.1.1.6 | ||
| This attribute describes the electrical or optical activity state of a lobe or the state of a port. Certain values may not be applicable in some cases | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3), standby(4) | ||
| stkHubTRPrtTrapMaskEnable | 1.3.6.1.4.1.164.7.2.3.1.1.7 | ||
| When this attribute is set to OFF by the management console the agent starts sending the unmasked traps related to this port. Otherwise no traps from this port are sent. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| stkHubTRPrtStatus | 1.3.6.1.4.1.164.7.2.3.1.1.8 | ||
| This attribute indicates the status of this lobe/port connection: DISABLED-(2) to (6) indicates the reason for the disabled state. INSERTED(7)indicates that the lobe hardware inserts this lobe into the ring , thus it becomes part of the ring BYPASSED(8)indicates that the ring bypasses this lobe and the lobe hardware provides loopback connection towards the station for media test purposes. FORCEDLOOP(9) indicates the port is in a loopback state and the main ring is connected to the backup path. TRUNKFAIL (10) indicates that the ring connection is broken for a repeater, converter or a cable protector. NORMAL(11) indicates the port is in normal condition It is not mandatory that a certain lobe/port will support all the enumerated states. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), disabledManual(2), disabledAutorec(3), disabledSecurity(4), disabledAuto(5), disabledFlip(6), inserted(7), bypass(8), forcedloop(9), trunkfail(10), normal(11) | ||
| stkHubTRPrtCableProtectEnable | 1.3.6.1.4.1.164.7.2.3.1.1.9 | ||
| The value of this attribute determines activation of the cable-fault protection mechanism of TCR and the optical link mechanism of TFR and TFC . | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3), inhibit(4) | ||
| stkHubTRPrtFlipProtectEnable | 1.3.6.1.4.1.164.7.2.3.1.1.10 | ||
| The value of this attribute determines activation of the flipping-lobe protection mechanism of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), on(3) | ||
| stkHubTRPrtMACAddress | 1.3.6.1.4.1.164.7.2.3.1.1.11 | ||
| The value of this object is the specific MAC address of this interface which uniquely identifies this Interface on a ring. | |||
| OBJECT-TYPE | |||
| MacAddress | |||
| stkHubTRPrtType | 1.3.6.1.4.1.164.7.2.3.1.1.12 | ||
| Type of the port specific hardware | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), tfr(2), tfc(3), tcr(4), tcp(5) | ||
| stkHubET | 1.3.6.1.4.1.164.7.3 | ||
| OBJECT IDENTIFIER | |||
| stkHubETMdl | 1.3.6.1.4.1.164.7.3.2 | ||
| OBJECT IDENTIFIER | |||
| stkHubETMdlTable | 1.3.6.1.4.1.164.7.3.2.1 | ||
| Bridge Hub Module table for ET media type Contains general information about the Module | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| StkHubETMdlEntry | |||
| stkHubETMdlEntry | 1.3.6.1.4.1.164.7.3.2.1.1 | ||
| An entry in table stkHubETMdlTable. | |||
| OBJECT-TYPE | |||
| StkHubETMdlEntry | |||
| stkHubETMdlID | 1.3.6.1.4.1.164.7.3.2.1.1.1 | ||
| A unique identifier of the module in stack. Internal module identifier is always 1 | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| stkHubETMdlLed | 1.3.6.1.4.1.164.7.3.2.1.1.2 | ||
| This entry specifies the LEDs status in the module . Each led will be represented by 4 bits where the first 2 bits will specify the status (NA, OFF, ON, BLINK), and the next two bits will specify the color (RED, GREEN, YELLOW) | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| stkHubETMdlReset | 1.3.6.1.4.1.164.7.3.2.1.1.3 | ||
| When this object is set to the value of hwReset(3), the module performs HW reset. When this object is set to the value of configReset(4), the module performs Configuration reset. Upon completion, a trap will be issued to the management station and the value will be set to OFF. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), off(2), hwReset(3), configReset(4) | ||
| radPS | 1.3.6.1.4.1.164.8 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSystem | 1.3.6.1.4.1.164.8.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysParam | 1.3.6.1.4.1.164.8.1.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysSParam | 1.3.6.1.4.1.164.8.1.1.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysX28PromptS | 1.3.6.1.4.1.164.8.1.1.1.1 | ||
| This specifies a different PAD prompt, instead of the standard default character, the *. Up to 10 characters can be entered. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| pktSwchSysHeraldS | 1.3.6.1.4.1.164.8.1.1.1.2 | ||
| This specifies the PAD herald message for the SPS-6 and SPS-12. Up to 32 characters can be entered. Other devices will return a zero length octet string and will send an error if this object is set to a string of any other length. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| pktSwchSysBulletinS | 1.3.6.1.4.1.164.8.1.1.1.3 | ||
| This specifies the PAD bulletin message. Up to 32 characters can be entered. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| pktSwchSysComPortSubAddS | 1.3.6.1.4.1.164.8.1.1.1.4 | ||
| This is the scratch command port with the desired subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysComPortAltSubAddS | 1.3.6.1.4.1.164.8.1.1.1.5 | ||
| This configures the command port with the second subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysInnerCommLenS | 1.3.6.1.4.1.164.8.1.1.1.6 | ||
| This specifies the address length in digits for Inner Communication. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..5 | ||
| pktSwchSysXOnCharS | 1.3.6.1.4.1.164.8.1.1.1.7 | ||
| The ASCII code of the software flow control character that will be used to start/renew the data transfer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchSysXOffCharS | 1.3.6.1.4.1.164.8.1.1.1.8 | ||
| The ASCII code of the software flow control character that will be used to stop the data transfer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchSysMaxLcnS | 1.3.6.1.4.1.164.8.1.1.1.9 | ||
| The maximum number of LCNs on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysMaxAIDS | 1.3.6.1.4.1.164.8.1.1.1.10 | ||
| The maximum number of AIDs on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysDeviceIdS | 1.3.6.1.4.1.164.8.1.1.1.11 | ||
| The device Id. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysAParam | 1.3.6.1.4.1.164.8.1.1.2 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysX28PromptA | 1.3.6.1.4.1.164.8.1.1.2.1 | ||
| This specifies the active PAD prompt. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..10) | ||
| pktSwchSysHeraldA | 1.3.6.1.4.1.164.8.1.1.2.2 | ||
| This specifies the active PAD herald message for the SPS-6 and SPS-12. Other devices will return a zero length string. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| pktSwchSysBulletinA | 1.3.6.1.4.1.164.8.1.1.2.3 | ||
| This indicates the active PAD bulletin message. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..32) | ||
| pktSwchSysComPortSubAddA | 1.3.6.1.4.1.164.8.1.1.2.4 | ||
| This is the active command port with the desired subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysComPortAltSubAddA | 1.3.6.1.4.1.164.8.1.1.2.5 | ||
| This is the active command port with the second subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysInnerCommLenA | 1.3.6.1.4.1.164.8.1.1.2.6 | ||
| This specifies the active address length in digits for Inner Communication. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..5 | ||
| pktSwchSysXOnCharA | 1.3.6.1.4.1.164.8.1.1.2.7 | ||
| The activeASCII code of the software flow control character that is used to start/renew the data transfer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchSysXOffCharA | 1.3.6.1.4.1.164.8.1.1.2.8 | ||
| The active ASCII code of the software flow control character that is used to stop the data transfer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchSysMaxLcnA | 1.3.6.1.4.1.164.8.1.1.2.9 | ||
| The active maximum number of LCNs on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysMaxAIDA | 1.3.6.1.4.1.164.8.1.1.2.10 | ||
| The active maximum number of AIDs on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysDeviceIdA | 1.3.6.1.4.1.164.8.1.1.2.11 | ||
| The device Id. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysEvRepS | 1.3.6.1.4.1.164.8.1.1.3 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysEvRepAdd1S | 1.3.6.1.4.1.164.8.1.1.3.1 | ||
| This specifies the X.25 address to which the reports selected by means of pktSwchSysEvRepMask1S and pktSwchSysEvRepPeriod1S will be sent. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysEvRepAdd2S | 1.3.6.1.4.1.164.8.1.1.3.2 | ||
| This specifies the X.25 address to which the reports selected by means of pktSwchSysEvRepMask2S and pktSwchSysEvRepPeriod2S will be sent. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysEvRepMask1S | 1.3.6.1.4.1.164.8.1.1.3.3 | ||
| This specifies the conditions on which reports are sent to the address specified in pktSwchSysEvRepAdd1S. The value is a sum of values (powers of two), where each value in the sum represents a condition. The values that may be included in the sum and their meanings are: 0 Disable event reports 1 Send report when SYNC status has changed 2 Send report when RTS status has changed 4 Send report at Power On (Reset) 8 Report charging information at CLR. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchSysEvRepPeriod1S | 1.3.6.1.4.1.164.8.1.1.3.4 | ||
| This specifies the time interval in minutes at which periodic reports are sent to the address specified in pktSwchSysEvRepAdd1S. A value of zero indicates that periodic reports are disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysEvRepMask2S | 1.3.6.1.4.1.164.8.1.1.3.5 | ||
| This specifies the conditions on which reports are sent to the address specified in pktSwchSysEvRepAdd2S. The value is a sum of values (powers of two), where each value in the sum represents a condition. The values that may be included in the sum and their meanings are: 0 Disable event reports 1 Send report when SYNC status has changed 2 Send report when RTS status has changed 4 Send report at Power On (Reset) 8 Report charging information at CLR. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchSysEvRepPeriod2S | 1.3.6.1.4.1.164.8.1.1.3.6 | ||
| This specifies the time interval in minutes at which periodic reports are sent to the address specified in pktSwchSysEvRepAdd2S. A value of zero indicates that periodic reports are disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSysEvRepRetryCntS | 1.3.6.1.4.1.164.8.1.1.3.7 | ||
| Number of retries to send Event Reports to each port. Possible values: 0 - Disable retry mechanism 1-255 - Number of retries | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysEvRepRetryDelayS | 1.3.6.1.4.1.164.8.1.1.3.8 | ||
| Time interval between retries (in minutes). Valid values: 1-255 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysEvRepRetryOptionsS | 1.3.6.1.4.1.164.8.1.1.3.9 | ||
| Event report options. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 - No Options 1 - Alternate Mode: Port 1 reports are readdressed to Port 2 on failure. (Port 2 mask is not used). 2 - Condensed Format X - Any combination of the above values | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysEvRepA | 1.3.6.1.4.1.164.8.1.1.4 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysEvRepAdd1A | 1.3.6.1.4.1.164.8.1.1.4.1 | ||
| This specifies the active X.25 address to which the reports selected by means of pktSwchSysEvRepMask1A and pktSwchSysEvRepPeriod1A will be sent. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysEvRepAdd2A | 1.3.6.1.4.1.164.8.1.1.4.2 | ||
| This specifies the active X.25 address to which the reports selected by means of pktSwchSysEvRepMask2A and pktSwchSysEvRepPeriod2A will be sent. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysEvRepMask1A | 1.3.6.1.4.1.164.8.1.1.4.3 | ||
| This specifies the active conditions on which reports are sent to the address specified in pktSwchSysEvRepAdd1A. The value is a sum of values (powers of two), where each value in the sum represents a condition. The values that may be included in the sum and their meanings are: 0 Disable event reports 1 Send report when SYNC status has changed 2 Send report when RTS status has changed 4 Send report at Power On (Reset) 8 Report charging information at CLR. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchSysEvRepPeriod1A | 1.3.6.1.4.1.164.8.1.1.4.4 | ||
| This specifies the active time interval in minutes at which periodic reports are sent to the address specified in pktSwchSysEvRepAdd1A. A value of zero indicates that periodic reports are disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pktSwchSysEvRepMask2A | 1.3.6.1.4.1.164.8.1.1.4.5 | ||
| This specifies the active conditions on which reports are sent to the address specified in pktSwchSysEvRepAdd2A. The value is a sum of values (powers of two), where each value in the sum represents a condition. The values that may be included in the sum and their meanings are: 0 Disable event reports 1 Send report when SYNC status has changed 2 Send report when RTS status has changed 4 Send report at Power On (Reset) 8 Report charging information at CLR. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchSysEvRepPeriod2A | 1.3.6.1.4.1.164.8.1.1.4.6 | ||
| This specifies the active time interval in minutes at which periodic reports are sent to the address specified in pktSwchSysEvRepAdd2A. A value of zero indicates that periodic reports are disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pktSwchSysEvRepRetryCntA | 1.3.6.1.4.1.164.8.1.1.4.7 | ||
| Number of retries to send Event Reports to each port. Possible values: 0 - Disable retry mechanism 1-255 - Number of retries | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysEvRepRetryDelayA | 1.3.6.1.4.1.164.8.1.1.4.8 | ||
| Time interval between retries (in minutes). Valid values: 1-255 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysEvRepRetryOptionsA | 1.3.6.1.4.1.164.8.1.1.4.9 | ||
| Event report options. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 - No Options 1 - Alternate Mode: Port 1 reports are readdressed to Port 2 on failure. (Port 2 mask is not used). 2 - Condensed Format X - Any combination of the above values | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysGen | 1.3.6.1.4.1.164.8.1.1.5 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSysDate | 1.3.6.1.4.1.164.8.1.1.5.1 | ||
| This is used to update the date on the device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysTime | 1.3.6.1.4.1.164.8.1.1.5.2 | ||
| This is used to update the time on the device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSysAction | 1.3.6.1.4.1.164.8.1.1.5.3 | ||
| This is used to perform imperitive commands on the device. The reset command resets the device with the scratch values. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), reset(2), resetStat(3), rearrangeNovram(4), setDefaultConfig(5) | ||
| pktSwchSysRamSize | 1.3.6.1.4.1.164.8.1.1.5.4 | ||
| The RAM size on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysNovramSize | 1.3.6.1.4.1.164.8.1.1.5.5 | ||
| The NOVRAM size on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysNovramUtil | 1.3.6.1.4.1.164.8.1.1.5.6 | ||
| The NOVRAM utilization on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysFreeDataBuff | 1.3.6.1.4.1.164.8.1.1.5.7 | ||
| The free data buffers on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysMinDataBuffInPool | 1.3.6.1.4.1.164.8.1.1.5.8 | ||
| The minimum data buffers in the pool on the device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysProtocols | 1.3.6.1.4.1.164.8.1.1.5.9 | ||
| The protocols the device can support. The value is a sum of values (powers of two), where each value in the sum represents a protocol. The values that may be included in the sum and their meanings are: 1 X.25 2 Frame Relay 4 HDLC 8 SDLC 16 MPE 32 ASYNC 64 STM-4 128 STM-8 256 STM-16 512 STM-24 1024 BISYNC 2048 SLIP 4096 ETHERNET 8192 PPP 16384 ISDN XX - Any combination of the values specified above . | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysChannelProtocols | 1.3.6.1.4.1.164.8.1.1.5.10 | ||
| The protocols the device can support on the async channels. 1 ASYNC 2 SLIP 3 PPP | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSysStatus | 1.3.6.1.4.1.164.8.1.1.6 | ||
| The status of the System data. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchRouting | 1.3.6.1.4.1.164.8.1.2 | ||
| OBJECT IDENTIFIER | |||
| pktSwchRoutSTable | 1.3.6.1.4.1.164.8.1.2.1 | ||
| The Scratch Routing Table defines the routes for incoming and outgoing data on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchRoutSEntry | |||
| pktSwchRoutSEntry | 1.3.6.1.4.1.164.8.1.2.1.1 | ||
| Defines the contents of each line in the Scratch Routing Table. | |||
| OBJECT-TYPE | |||
| PktSwchRoutSEntry | |||
| pktSwchRoutIdS | 1.3.6.1.4.1.164.8.1.2.1.1.1 | ||
| Index of the pktSwchRoutSTable. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..2000 | ||
| pktSwchRoutAddressS | 1.3.6.1.4.1.164.8.1.2.1.1.2 | ||
| The address to which the entry applies. The use of the octet string syntax allows the use of the letter x as a wild card in the addresses. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink1S | 1.3.6.1.4.1.164.8.1.2.1.1.3 | ||
| First destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink2S | 1.3.6.1.4.1.164.8.1.2.1.1.4 | ||
| Second destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink3S | 1.3.6.1.4.1.164.8.1.2.1.1.5 | ||
| Third destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutLinkPrio1S | 1.3.6.1.4.1.164.8.1.2.1.1.6 | ||
| A priority of the associated destination of link 1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutLinkPrio2S | 1.3.6.1.4.1.164.8.1.2.1.1.7 | ||
| A priority of the associated destination of link 2. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutLinkPrio3S | 1.3.6.1.4.1.164.8.1.2.1.1.8 | ||
| A priority of the associated destination of link 3. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutSearchStatusS | 1.3.6.1.4.1.164.8.1.2.1.1.9 | ||
| off - The device stops searching for a matching address. on - The device continues searching for a matching address in the links of the next entry. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| pktSwchRoutStatusS | 1.3.6.1.4.1.164.8.1.2.1.1.10 | ||
| The status of this routing table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchRoutATable | 1.3.6.1.4.1.164.8.1.2.2 | ||
| The Active Routing Table defines the active routes for incoming and outgoing data on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchRoutAEntry | |||
| pktSwchRoutAEntry | 1.3.6.1.4.1.164.8.1.2.2.1 | ||
| Defines the contents of each line in the Active Routing Table. | |||
| OBJECT-TYPE | |||
| PktSwchRoutAEntry | |||
| pktSwchRoutIdA | 1.3.6.1.4.1.164.8.1.2.2.1.1 | ||
| Index of the pktSwchRoutATable. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..2000 | ||
| pktSwchRoutAddressA | 1.3.6.1.4.1.164.8.1.2.2.1.2 | ||
| The address to which the entry applies. The use of the octet string syntax allows the use of the letter x as a wild card in the addresses. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink1A | 1.3.6.1.4.1.164.8.1.2.2.1.3 | ||
| First destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink2A | 1.3.6.1.4.1.164.8.1.2.2.1.4 | ||
| Second destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutDestLink3A | 1.3.6.1.4.1.164.8.1.2.2.1.5 | ||
| Third destination link through which the data will be routed. For X.25 destination: any valid x.25 link no. For Frame Relay Link: any valid dlci with an x.25 encapsulation protocol, presented in the form of {port:dlci}. For a local destination: 100 . For ISDN: ISDN routing entry number preceeded by the letter 'I' (example: I4) | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchRoutLinkPrio1A | 1.3.6.1.4.1.164.8.1.2.2.1.6 | ||
| A priority of the associated destination of link 1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutLinkPrio2A | 1.3.6.1.4.1.164.8.1.2.2.1.7 | ||
| A priority of the associated destination of link 2. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutLinkPrio3A | 1.3.6.1.4.1.164.8.1.2.2.1.8 | ||
| A priority of the associated destination of link 3. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchRoutSearchStatusA | 1.3.6.1.4.1.164.8.1.2.2.1.9 | ||
| off - The device stops searching for a matching address. on - The device continues searching for a matching address in the links of the next entry. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| pktSwchPvcSTable | 1.3.6.1.4.1.164.8.1.2.3 | ||
| The Scratch Network PVC Table defines the network PVCs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPvcSEntry | |||
| pktSwchPvcSEntry | 1.3.6.1.4.1.164.8.1.2.3.1 | ||
| Defines the contents of each line in the Scratch Network PVC table. | |||
| OBJECT-TYPE | |||
| PktSwchPvcSEntry | |||
| pktSwchPvcNumS | 1.3.6.1.4.1.164.8.1.2.3.1.1 | ||
| The PVC number corresponding to this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchPvcSrcLinkS | 1.3.6.1.4.1.164.8.1.2.3.1.2 | ||
| The number of the link (1 through 6 for SPS-6 and 1 through 12 for SPS-12) that will be used as a source link to create a connection by means of the PVC. 0 means that the PVC will not be active, 100 means that this pvc is Local. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| pktSwchPvcSrcLcnS | 1.3.6.1.4.1.164.8.1.2.3.1.3 | ||
| Network pvc: The number of the logical channel (0-255) that will be used as the source logical channel to create a connection by means of the PVC. Local pvc: For asynchronous channel to X.25 PVC, Any valid Async Channel number. For encapsulation of transparent HDLC over X25 PVC, valid Channel numbers are: HxM - for the main PVC. HxB - for the backup PVC. x is a valid HDLC link number. For encapsulation of Multi Point Encapsulator (MPE) over X25 PVC, valid channel numbers are: Nx - where x is a valid MPE link number. For encapsulation of IP Over X.25 PVC, Enter IP. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchPvcDstLinkS | 1.3.6.1.4.1.164.8.1.2.3.1.4 | ||
| The number of the destination link that will be used. 0 means that the PVC will not be active. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..12 | ||
| pktSwchPvcDstLcnS | 1.3.6.1.4.1.164.8.1.2.3.1.5 | ||
| The number of the logical channel for the destination link. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchPvcStatusS | 1.3.6.1.4.1.164.8.1.2.3.1.6 | ||
| The status of this Network PVC table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchPvcATable | 1.3.6.1.4.1.164.8.1.2.4 | ||
| The Active Network PVC Table defines the active network PVCs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPvcAEntry | |||
| pktSwchPvcAEntry | 1.3.6.1.4.1.164.8.1.2.4.1 | ||
| Defines the contents of each line in the Active Network PVC table. | |||
| OBJECT-TYPE | |||
| PktSwchPvcAEntry | |||
| pktSwchPvcNumA | 1.3.6.1.4.1.164.8.1.2.4.1.1 | ||
| The PVC number corresponding to this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchPvcSrcLinkA | 1.3.6.1.4.1.164.8.1.2.4.1.2 | ||
| The number of the link (1 through 6 for SPS-6 and 1 through 12 for SPS-12) that is used as a source link to create a connection by means of the PVC. 0 means that the PVC will not be active, 100 means that this pvc is Local. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..100 | ||
| pktSwchPvcSrcLcnA | 1.3.6.1.4.1.164.8.1.2.4.1.3 | ||
| Network pvc: The number of the logical channel (0-255) that will be used as the source logical channel to create a connection by means of the PVC. Local pvc: For asynchronous channel to X.25 PVC, Any valid Async Channel number. For encapsulation of transparent HDLC over X25 PVC, valid Channel numbers are: HxM - for the main PVC. HxB - for the backup PVC. x is a valid HDLC link number. For encapsulation of Multi Point Encapsulator (MPE) over X25 PVC, valid channel numbers are: Nx - where x is a valid MPE link number. For encapsulation of IP Over X.25 PVC, Enter IP. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchPvcDstLinkA | 1.3.6.1.4.1.164.8.1.2.4.1.4 | ||
| The number of the destination link that is used. 0 means that the PVC will not be active. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..12 | ||
| pktSwchPvcDstLcnA | 1.3.6.1.4.1.164.8.1.2.4.1.5 | ||
| The number of the logical channel for the destination link. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchNui | 1.3.6.1.4.1.164.8.1.3 | ||
| OBJECT IDENTIFIER | |||
| pktSwchNuiSTable | 1.3.6.1.4.1.164.8.1.3.1 | ||
| The NUI Table defines the NUIs that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiSEntry | |||
| pktSwchNuiSEntry | 1.3.6.1.4.1.164.8.1.3.1.1 | ||
| Defines the contents of each line in the NUI Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiSEntry | |||
| pktSwchNuiIndexS | 1.3.6.1.4.1.164.8.1.3.1.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiGroupIdS | 1.3.6.1.4.1.164.8.1.3.1.1.2 | ||
| The group Id for this NUI entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiInPasswdS | 1.3.6.1.4.1.164.8.1.3.1.1.3 | ||
| The password for the incoming call. 15 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutPasswdPointerS | 1.3.6.1.4.1.164.8.1.3.1.1.4 | ||
| A pointer to the password in the OutPasswdTable for an outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiInAddrS | 1.3.6.1.4.1.164.8.1.3.1.1.5 | ||
| The addresss for the incoming call. 15 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutAddrPointerS | 1.3.6.1.4.1.164.8.1.3.1.1.6 | ||
| A pointer to the address in the OutAddrTable for an outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiStatusS | 1.3.6.1.4.1.164.8.1.3.1.1.7 | ||
| The status of this NUI table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchNuiATable | 1.3.6.1.4.1.164.8.1.3.2 | ||
| The NUI Table defines the NUIs that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiAEntry | |||
| pktSwchNuiAEntry | 1.3.6.1.4.1.164.8.1.3.2.1 | ||
| Defines the contents of each line in the NUI Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiAEntry | |||
| pktSwchNuiIndexA | 1.3.6.1.4.1.164.8.1.3.2.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiGroupIdA | 1.3.6.1.4.1.164.8.1.3.2.1.2 | ||
| The group Id for this NUI entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiInPasswdA | 1.3.6.1.4.1.164.8.1.3.2.1.3 | ||
| The password for the incoming call. 15 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutPasswdPointerA | 1.3.6.1.4.1.164.8.1.3.2.1.4 | ||
| A pointer to the password in the OutPasswdTable for an outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiInAddrA | 1.3.6.1.4.1.164.8.1.3.2.1.5 | ||
| The addresss for the incoming call. 15 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutAddrPointerA | 1.3.6.1.4.1.164.8.1.3.2.1.6 | ||
| A pointer to the address in the OutAddrTable for an outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiStatusA | 1.3.6.1.4.1.164.8.1.3.2.1.7 | ||
| The status of this NUI table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchNuiOutPasswdSTable | 1.3.6.1.4.1.164.8.1.3.3 | ||
| The table defines the passwords that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiOutPasswdSEntry | |||
| pktSwchNuiOutPasswdSEntry | 1.3.6.1.4.1.164.8.1.3.3.1 | ||
| Defines the contents of each line in OutPasswd Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiOutPasswdSEntry | |||
| pktSwchNuiOutPasswdIndexS | 1.3.6.1.4.1.164.8.1.3.3.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiOutPasswdValueS | 1.3.6.1.4.1.164.8.1.3.3.1.2 | ||
| The password of this entry. 15 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutPasswdStatusS | 1.3.6.1.4.1.164.8.1.3.3.1.3 | ||
| The status of this NuiOutPasswd table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchNuiOutPasswdATable | 1.3.6.1.4.1.164.8.1.3.4 | ||
| The table defines the passwords that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiOutPasswdAEntry | |||
| pktSwchNuiOutPasswdAEntry | 1.3.6.1.4.1.164.8.1.3.4.1 | ||
| Defines the contents of each line in OutPasswd Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiOutPasswdAEntry | |||
| pktSwchNuiOutPasswdIndexA | 1.3.6.1.4.1.164.8.1.3.4.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiOutPasswdValueA | 1.3.6.1.4.1.164.8.1.3.4.1.2 | ||
| The password of this entry. 15 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutPasswdStatusA | 1.3.6.1.4.1.164.8.1.3.4.1.3 | ||
| The status of this NuiOutPasswd table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchNuiOutAddrSTable | 1.3.6.1.4.1.164.8.1.3.5 | ||
| The table defines the Addresses that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiOutAddrSEntry | |||
| pktSwchNuiOutAddrSEntry | 1.3.6.1.4.1.164.8.1.3.5.1 | ||
| Defines the contents of each line in OutAddr Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiOutAddrSEntry | |||
| pktSwchNuiOutAddrIndexS | 1.3.6.1.4.1.164.8.1.3.5.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiOutAddrValueS | 1.3.6.1.4.1.164.8.1.3.5.1.2 | ||
| The address of this entry. 15 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutAddrStatusS | 1.3.6.1.4.1.164.8.1.3.5.1.3 | ||
| The status of this NuiOutAddr table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchNuiOutAddrATable | 1.3.6.1.4.1.164.8.1.3.6 | ||
| The table defines the Addresses that can be used by the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchNuiOutAddrAEntry | |||
| pktSwchNuiOutAddrAEntry | 1.3.6.1.4.1.164.8.1.3.6.1 | ||
| Defines the contents of each line in OutAddr Table. | |||
| OBJECT-TYPE | |||
| PktSwchNuiOutAddrAEntry | |||
| pktSwchNuiOutAddrIndexA | 1.3.6.1.4.1.164.8.1.3.6.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchNuiOutAddrValueA | 1.3.6.1.4.1.164.8.1.3.6.1.2 | ||
| The address of this entry. 15 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchNuiOutAddrStatusA | 1.3.6.1.4.1.164.8.1.3.6.1.3 | ||
| The status of this NuiOutAddr table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchMng | 1.3.6.1.4.1.164.8.1.4 | ||
| OBJECT IDENTIFIER | |||
| pktSwchMngX25TrapIpTable | 1.3.6.1.4.1.164.8.1.4.1 | ||
| This table indicates the destination address of the traps. Internally it will be limited to ten addresses. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchMngX25Entry | |||
| pktSwchMngX25Entry | 1.3.6.1.4.1.164.8.1.4.1.1 | ||
| An entry in table pktSwchMngX25TrapIpTable. | |||
| OBJECT-TYPE | |||
| PktSwchMngX25Entry | |||
| pktSwchMngID | 1.3.6.1.4.1.164.8.1.4.1.1.1 | ||
| This value indicates an index of a specific IP address | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchMngIP | 1.3.6.1.4.1.164.8.1.4.1.1.2 | ||
| This value indicates the destination address of the traps. IP 0.0.0.0 removes the entry. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchMngPhyAddr | 1.3.6.1.4.1.164.8.1.4.1.1.3 | ||
| This value indicates the physical destination address of the traps. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchTrapEnable | 1.3.6.1.4.1.164.8.1.4.1.1.4 | ||
| This value indicates which traps should be sent. The value is a sum of values (powers of two), where each value in the sum represents a trap that should be reported to the Management Station. The values that may be included in the sum and their meanings are: 0 No traps would be reported. 1 Link Down 2 Link Up 4 rtsChange 8 resetX25 16 restartX25 32 frDLCIStatusChange 64 coldStart 128 linkProtocolChanged 256 enrollmentPS 512 ledStatusChange | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchEncapsulationMode | 1.3.6.1.4.1.164.8.1.4.1.1.5 | ||
| Format type for IP over X25 | |||
| OBJECT-TYPE | |||
| INTEGER | ipPid(1), snapPid(2) | ||
| pktSwchXid | 1.3.6.1.4.1.164.8.1.5 | ||
| OBJECT IDENTIFIER | |||
| pktSwchXidSTable | 1.3.6.1.4.1.164.8.1.5.1 | ||
| The Exchange Id table contains a list of 13 incoming pairs of allowed dial-up phone numbers and passwords. Also included is one pair of outgoing phone number and password (InternalIndex=14). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchXidSEntry | |||
| pktSwchXidSEntry | 1.3.6.1.4.1.164.8.1.5.1.1 | ||
| An entry in table pktSwchXidSTable. | |||
| OBJECT-TYPE | |||
| PktSwchXidSEntry | |||
| pktSwchXidIndexS | 1.3.6.1.4.1.164.8.1.5.1.1.1 | ||
| This Index of the XID table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchXidInternalIndexS | 1.3.6.1.4.1.164.8.1.5.1.1.2 | ||
| An internal index for each XidIndex of the table. The first 13 entries refer to Incoming calls. The 14th entry refers to an Outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchXidPasswdS | 1.3.6.1.4.1.164.8.1.5.1.1.3 | ||
| Password of size 16 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchXidPhoneS | 1.3.6.1.4.1.164.8.1.5.1.1.4 | ||
| Phone number of size 16 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchXidStatusS | 1.3.6.1.4.1.164.8.1.5.1.1.5 | ||
| The status of the XID table entry. The status applies to the XidIndex, i.e., setting the staus to invalid results in the removal of all the InternalIndex entries (1..14) belonging to the relevant XidIndex. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchXidATable | 1.3.6.1.4.1.164.8.1.5.2 | ||
| The Exchange Id table contains a list of 13 incoming pairs of allowed dial-up phone numbers and passwords. Also included is one pair of outgoing phone number and password (InternalIndex=14). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchXidAEntry | |||
| pktSwchXidAEntry | 1.3.6.1.4.1.164.8.1.5.2.1 | ||
| An entry in table pktSwchXidATable. | |||
| OBJECT-TYPE | |||
| PktSwchXidAEntry | |||
| pktSwchXidIndexA | 1.3.6.1.4.1.164.8.1.5.2.1.1 | ||
| This Index of the XID table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchXidInternalIndexA | 1.3.6.1.4.1.164.8.1.5.2.1.2 | ||
| An internal index for each XidIndex of the table. The first 13 entries refer to Incoming calls. The 14th entry refers to an Outgoing call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchXidPasswdA | 1.3.6.1.4.1.164.8.1.5.2.1.3 | ||
| Password of size 16 chars. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchXidPhoneA | 1.3.6.1.4.1.164.8.1.5.2.1.4 | ||
| Phone number of size 16 digits. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchXidStatusA | 1.3.6.1.4.1.164.8.1.5.2.1.5 | ||
| The status of the XID table entry. The status applies to the XidIndex, i.e., setting the staus to invalid results in the removal of all the InternalIndex entries (1..14) belonging to the relevant XidIndex. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIpRouting | 1.3.6.1.4.1.164.8.1.6 | ||
| OBJECT IDENTIFIER | |||
| pktSwchIpRoutSTable | 1.3.6.1.4.1.164.8.1.6.1 | ||
| The Scratch Routing Table defines the routes for incoming and outgoing ip datagrams on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIpRoutSEntry | |||
| pktSwchIpRoutSEntry | 1.3.6.1.4.1.164.8.1.6.1.1 | ||
| Defines the contents of each line in the Scratch IP Routing Table. | |||
| OBJECT-TYPE | |||
| PktSwchIpRoutSEntry | |||
| pktSwchIpRoutIdS | 1.3.6.1.4.1.164.8.1.6.1.1.1 | ||
| Index of the pktSwchIpRoutSTable. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIpRoutIpAddressS | 1.3.6.1.4.1.164.8.1.6.1.1.2 | ||
| The IP address to which the entry applies. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutIpMaskS | 1.3.6.1.4.1.164.8.1.6.1.1.3 | ||
| The IP mask to which the entry applies. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutDestProtocolS | 1.3.6.1.4.1.164.8.1.6.1.1.4 | ||
| Destination protocol for the associated address. None(255) when not used | |||
| OBJECT-TYPE | |||
| INTEGER | slip(1), x25SVC(2), x25PVC(3), frameRelay(4), hdlc(5), ethernet(7), ppp(8), none(255) | ||
| pktSwchIpRoutDestinationS | 1.3.6.1.4.1.164.8.1.6.1.1.5 | ||
| Destination for the associated address. Possible values: Default : Not Used. X.25 PVC: Port:LCN or a pre defined PVC number X.25 SVC: X.25 Addr or cid followed by a predefined Call ID number Frame Relay: Port:DLCI HDLC: 'H' followed by the HDLC Port Number SLIP: 'S' followed by the SLIP Channel Number Ethernet: 'E' followed by the Ethernet Port Number PPP: 'P' followed by the PPP Port Number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchIpRoutInactivityS | 1.3.6.1.4.1.164.8.1.6.1.1.6 | ||
| Inactivity time in steps of 50 mili seconds for X25 SVC protocol only. Range: 0..255. Default: 2. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpRoutStatusS | 1.3.6.1.4.1.164.8.1.6.1.1.7 | ||
| The status of this routing table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIpRoutMetricS | 1.3.6.1.4.1.164.8.1.6.1.1.8 | ||
| No. of hops for this route. The default value is 1. Legal values: 1 to the max no. of hops this device will support. The max no. is defined by pktSwchIpGlobalMaxHopCount. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpRoutNextHopS | 1.3.6.1.4.1.164.8.1.6.1.1.9 | ||
| IP address of the next hop. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutInterfaceIdS | 1.3.6.1.4.1.164.8.1.6.1.1.10 | ||
| ID of the logical IP interface in the pktSwchIpInterface table. The IP routing module will route the IP frame according to this interface ID. Legal values: 1 to 200 and 65535. 1-200 : ID of interface. 65535 : No IP interface ID. Default value: 65535. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpRoutATable | 1.3.6.1.4.1.164.8.1.6.2 | ||
| The Active Routing Table defines the active routes for incoming and outgoing ip datagrams on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIpRoutAEntry | |||
| pktSwchIpRoutAEntry | 1.3.6.1.4.1.164.8.1.6.2.1 | ||
| Defines the contents of each line in the Active IP Routing Table. | |||
| OBJECT-TYPE | |||
| PktSwchIpRoutAEntry | |||
| pktSwchIpRoutIdA | 1.3.6.1.4.1.164.8.1.6.2.1.1 | ||
| Index of the IP pktSwchIpRoutATable. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIpRoutIpAddressA | 1.3.6.1.4.1.164.8.1.6.2.1.2 | ||
| The IP address to which the entry applies. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutIpMaskA | 1.3.6.1.4.1.164.8.1.6.2.1.3 | ||
| The IP mask to which the entry applies. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutDestProtocolA | 1.3.6.1.4.1.164.8.1.6.2.1.4 | ||
| Destination protocol for the associated address. None(255) when not used. | |||
| OBJECT-TYPE | |||
| INTEGER | slip(1), x25SVC(2), x25PVC(3), frameRelay(4), hdlc(5), snmpAgent(6), ethernet(7), ppp(8), none(255) | ||
| pktSwchIpRoutDestinationA | 1.3.6.1.4.1.164.8.1.6.2.1.5 | ||
| Destination for the associated address. Possible values: Default : Not Used. X.25 PVC: Port:LCN or a pre defined PVC number X.25 SVC: X.25 Addr or cid followed by a predefined Call ID number Frame Relay: Port:DLCI HDLC: 'H' followed by the HDLC Port Number SLIP: 'S' followed by the SLIP Channel Number Ethernet: 'E' followed by the Ethernet Port Number PPP: 'P' followed by the PPP Port Number. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchIpRoutInactivityA | 1.3.6.1.4.1.164.8.1.6.2.1.6 | ||
| Inactivity time in steps of 50 mili seconds for X25 SVC protocol only. Range: 0..255. Default: 2. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpRoutBuffsInA | 1.3.6.1.4.1.164.8.1.6.2.1.7 | ||
| The number of packets in the Input buffer link list, received but not routed yet. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpRoutBuffsOutA | 1.3.6.1.4.1.164.8.1.6.2.1.8 | ||
| The number of packets in the Output buffer link list, routed but not sent yet. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpRoutFCA | 1.3.6.1.4.1.164.8.1.6.2.1.9 | ||
| This is the flow control status of this ip routing entry\connection | |||
| OBJECT-TYPE | |||
| INTEGER | discard(1), flowControl(2), normal(3) | ||
| pktSwchIpRoutMetricA | 1.3.6.1.4.1.164.8.1.6.2.1.10 | ||
| No. of hops for this route. The default value is 1. Legal values: 1 to the max no. of hops this device will support. The max no. is defined by pktSwchIpGlobalMaxHopCount. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpRoutNextHopA | 1.3.6.1.4.1.164.8.1.6.2.1.11 | ||
| IP address of the next hop. A string of the format: X.X.X.X where every X is a number in the range 0-255. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpRoutInterfaceIdA | 1.3.6.1.4.1.164.8.1.6.2.1.12 | ||
| ID of the logical IP interface in the pktSwchIpInterface table. The IP routing module will route the IP frame according to this interface ID. Legal values: 1 to 200 and 65535. 1-200 : ID of interface. 65535 : No IP interface ID. Default value: 65535. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPriority | 1.3.6.1.4.1.164.8.1.7 | ||
| OBJECT IDENTIFIER | |||
| pktSwchTxPriorityStatus | 1.3.6.1.4.1.164.8.1.7.1 | ||
| The status of the Priorities table. Used for saving the Priority parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchTxPriorityTable | 1.3.6.1.4.1.164.8.1.7.2 | ||
| The Tx Priorities table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchTxPriorityEntry | |||
| pktSwchTxPriorityEntry | 1.3.6.1.4.1.164.8.1.7.2.1 | ||
| The Tx Priority Entry defines the max delay time and max queue length for each Priority level. | |||
| OBJECT-TYPE | |||
| PktSwchTxPriorityEntry | |||
| pktSwchTxPriorityLevel | 1.3.6.1.4.1.164.8.1.7.2.1.1 | ||
| Level of an entry in the Tx Priority Table. At present, the PS supports 4 priority levels. Default level: 1 | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| pktSwchTxPriorityMaxDelayTime | 1.3.6.1.4.1.164.8.1.7.2.1.2 | ||
| Max delay time in Tx queue (in 100 msec intervals). Each frame will wait no more than the Max delay time until it is handled. 0 means that the delay is Unlimited. Default value: 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..60000 | ||
| pktSwchTxPriorityMaxQueueLen | 1.3.6.1.4.1.164.8.1.7.2.1.3 | ||
| Max allowed length of the Tx queue. Frames will be discarded if the length is exceeded. 0 means that the queue is of Unlimited length. Default value: 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65535 | ||
| pktSwchAsync | 1.3.6.1.4.1.164.8.2 | ||
| OBJECT IDENTIFIER | |||
| pktSwchProfile | 1.3.6.1.4.1.164.8.2.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchProfileSTable | 1.3.6.1.4.1.164.8.2.1.1 | ||
| The Profile Table S defines the Scratch profiles that the PS can use to configure a channel. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchProfileSEntry | |||
| pktSwchProfileSEntry | 1.3.6.1.4.1.164.8.2.1.1.1 | ||
| Defines the contents of each line in the Profile Table S. | |||
| OBJECT-TYPE | |||
| PktSwchProfileSEntry | |||
| pktSwchProfileNumberS | 1.3.6.1.4.1.164.8.2.1.1.1.1 | ||
| The number by which a profile is identified. This is also used as the index for the profile table. The maximum profile number is 200. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchProfileRecallCharS | 1.3.6.1.4.1.164.8.2.1.1.1.2 | ||
| The character specified by this entry is used to escape from the data transfer mode and enter the PAD command mode. The integer values have the following meanings: (0) PAD recall is not possible (1) The PAD recall character is DLE (2) to (126) The PAD recall character is specified by the user by entering its ASCII code. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchProfileEchoS | 1.3.6.1.4.1.164.8.2.1.1.1.3 | ||
| This determines if an echo of the input characters is retured to the DTE. The options are either 'echo enabled' or 'no echo'. | |||
| OBJECT-TYPE | |||
| INTEGER | echEn(1), noEch(2) | ||
| pktSwchProfileDataForwCharS | 1.3.6.1.4.1.164.8.2.1.1.1.4 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) used as a data forwarding character. The data forwarding characters are used to instruct the PAD to complete the assembly of and to forward a packet containing the data accumulated up to the reception of such a character. The values that may be included in the sum and their meanings are: 0 Data forwarding characters are not used 1 Alpha-numeric characters (A to Z, a to z, 0 to 9, inclusive) 2 Character CR 4 Characters ESC, BEL, ENQ, ACK 8 Characters DEL, CAN, DC2 16 Characters EOT, ETX 32 Characters HT, LF, VT, FF 64 All the other characters in colums 0 and 1 of IA5 and not listed above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileIdleTimerS | 1.3.6.1.4.1.164.8.2.1.1.1.5 | ||
| Packets will be forwarded when the idle timer expires. The idle time interval is specified as a multiple of 50 milliseconds. The multiple is given by the parameter value. For example, a value of 60 sets an interval of 3 seconds. If the parameter value is 0, no forwarding occurs after the idle condition. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileDevFlowContS | 1.3.6.1.4.1.164.8.2.1.1.1.6 | ||
| This parameter determines whether or not the PAD uses software flow control for the attached device. The options are either (1) PAD uses flow control during data transfer mode, (2) PAD uses flow control both in the data transfer mode and in the command mode, or (255) PAD does not use flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | trans(1), transAndCom(2), noFlow(255) | ||
| pktSwchProfileServSigS | 1.3.6.1.4.1.164.8.2.1.1.1.7 | ||
| This parameter is used to instruct the PAD whether to transfer PAD service signals and the PAD prompt to the local DTE in standard format. The options are (1) PAD service signals are transmitted to the DTE using the standard format, (4) The PAD prompt is transmitted using the standard format, (5) PAD service signals and the PAD prompt are transmitted in the standard format, or (255) No PAD service signals are transmitted to the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | serv(1), prompt(4), servAndPrompt(5), noSig(255) | ||
| pktSwchProfileBreakS | 1.3.6.1.4.1.164.8.2.1.1.1.8 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a PAD operation on receipt of the break signal from the DTE. The values that may be included in the sum and their meanings are: 0 Nothing 1 Send interrupt packet to network 2 Send RESET packet to network 4 Send and 'indication of break' message 8 Escape from data transfer mode 16 Discard output data waiting to be sent to the DTE . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..31 | ||
| pktSwchProfileDiscOutS | 1.3.6.1.4.1.164.8.2.1.1.1.9 | ||
| This parameter instructs the PAD whether to forward the user sequences included in data packets to the local DTE or discard them. The options are (1) discard output or (2) normal data delivery. If the value of radSPSProfileBreak is 21, the value of pktSwchProfileDiscOut is automatically set to (1) when a break signal is received. | |||
| OBJECT-TYPE | |||
| INTEGER | discOut(1), normal(2) | ||
| pktSwchProfileCRPaddingS | 1.3.6.1.4.1.164.8.2.1.1.1.10 | ||
| This parameter specifies the number of padding characters to be added after a carriage return character is transmitted to the local DTE. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineFoldS | 1.3.6.1.4.1.164.8.2.1.1.1.11 | ||
| This parameter specifies the maximum number of characters to be inserted before the format effector. If the value is zero, there is no insertion of a format effector (line folding). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileSpeedS | 1.3.6.1.4.1.164.8.2.1.1.1.12 | ||
| This parameter determines the rate of data transmission to and from the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21) | ||
| pktSwchProfilePadFlowContS | 1.3.6.1.4.1.164.8.2.1.1.1.13 | ||
| This determines whether or not the terminal can exercise flow control over the PAD. The options are either 'device can exercise flow control' or 'device cannot exercise flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | flowCont(1), noFlowCont(2) | ||
| pktSwchProfileLineFeedInsertS | 1.3.6.1.4.1.164.8.2.1.1.1.14 | ||
| This parameter indicates when there is a line feed insertion after CR. The options are (1) Insert line feed after transmission of CR to the DTE, (2) Insert line feed after receipt of CR from the DTE, (4) Insert line feed after echoing a CR character to the DTE, (5) Combination of (1) and (4), (6) Insert line feed after any CR to the DTE (combination of (2) and (4)), (7) Combination of (1), (2), and (4), or (255) No line feed insertion. | |||
| OBJECT-TYPE | |||
| INTEGER | afterCR(1), recCR(2), echoCR(4), onePlusFour(5), twoPlusFour(6), oneTwoFour(7), noFeed(255) | ||
| pktSwchProfileLineFeedPadS | 1.3.6.1.4.1.164.8.2.1.1.1.15 | ||
| This parameter specifies the number of padding characters to be added after a line feed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileEditingS | 1.3.6.1.4.1.164.8.2.1.1.1.16 | ||
| This parameter specifies the editing capabilities available in the data transfer mode. Editing is always possible when the PAD is in the command mode. The options are (1) Command editing in the data trasfer mode is enabled or (2) No command editing in the data transfer mode. | |||
| OBJECT-TYPE | |||
| INTEGER | edit(1), noEdit(2) | ||
| pktSwchProfileCharDelS | 1.3.6.1.4.1.164.8.2.1.1.1.17 | ||
| This parameter specifies the character delete, which is one character from IA5. The default selection is 127 (character DEL). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineDelS | 1.3.6.1.4.1.164.8.2.1.1.1.18 | ||
| This parameter specifies the line delete (last line stored in the edit buffer), which is one character from IA5. The default selection is 24 (character CAN). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineDispS | 1.3.6.1.4.1.164.8.2.1.1.1.19 | ||
| This entry specifies the line display character, which is one character from IA5. The default selection is 18 (character DC2). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileEditServSigS | 1.3.6.1.4.1.164.8.2.1.1.1.20 | ||
| This entry specifies the editing PAD service signals. The integer values have the following meanings: (0) No editing PAD service signals (1) Editing PAD service signals for printing terminals (2) Editing PAD service signals for display terminals (3) to (126) Editing PAD service signals using the desired character from IA5. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchProfileEchomaskS | 1.3.6.1.4.1.164.8.2.1.1.1.21 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) included in the echo mask. The characters in the echo mask are not echoed to the DTE when PAD echo is enabled. The values that may be included in the sum and their meanings are: 0 No echo mask (all the characters are echoed) 1 No echo of character CR 2 No echo of character LF 4 No echo of characters VT, HT, FF 8 No echo of characters BEL, BS 16 No echo of characters ESC, ENQ 32 No echo of characters ACK, NAK, STX, SOH, EOT, ETB, ETX 64 No echo of the editing characters selected by radSPSProfileCharDel, radSPSProfileLineDel, and radSPSProfileLineDisp 128 No echo of the DEL character and of all the other characters in the range of ASCII 00 through 31 not mentioned above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileParTreatS | 1.3.6.1.4.1.164.8.2.1.1.1.22 | ||
| This entry controls the generation of parity bits in the data sent to the local DTE and the checking of the parity bit when generated by the local DTE. The options are (1) parity checking is enabled, (2) parity generation is enabled, (3) parity checking and generation are enabled, or (255) no parity checking nor parity generation. | |||
| OBJECT-TYPE | |||
| INTEGER | parCheck(1), parGen(2), checkAndGen(3), noPar(255) | ||
| pktSwchProfilePageWaitS | 1.3.6.1.4.1.164.8.2.1.1.1.23 | ||
| This entry specifies the number of line feed characters counted by the PAD before the page wait condition is entered. If the value is zero, page wait is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileBitsPerCharS | 1.3.6.1.4.1.164.8.2.1.1.1.24 | ||
| The number of data bits per character supported by the PAD. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..8 | ||
| pktSwchProfileDvParityS | 1.3.6.1.4.1.164.8.2.1.1.1.25 | ||
| This entry selects the type of parity to be checked and or generated by the PAD when radSPSProfileParTreat is a value other than 255. The options are (1) space parity, (2) mark parity, (3) even parity, (4) odd parity, or (255) no parity. | |||
| OBJECT-TYPE | |||
| INTEGER | space(1), mark(2), even(3), odd(4), none(255) | ||
| pktSwchProfileStopBitsS | 1.3.6.1.4.1.164.8.2.1.1.1.26 | ||
| This entry indicates the number of stop bits per character supported by the PAD. The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), oneAndHalf(3) | ||
| pktSwchProfileSpecFlowS | 1.3.6.1.4.1.164.8.2.1.1.1.27 | ||
| This entry is used to define additional flow control possiblilites. The options are either (1) Flow control by means of the terminal DTR line or (2) No special flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | spec(1), noSpec(2) | ||
| pktSwchProfileCountFwdS | 1.3.6.1.4.1.164.8.2.1.1.1.28 | ||
| This entry can be used to instruct the PAD to complete the assembly of a packet and to forward it after the specifed number of characters has been received. If the value is zero, count forwarding is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileEscDelayS | 1.3.6.1.4.1.164.8.2.1.1.1.29 | ||
| This entry can be used to instruct the PAD whether to delay the forwarding of a data packet when an escape character is detected in the data stream and to determine the required delay. The packet forwarding is delayed until the specified number of characters is received after the escape character. A value of zero indicates no special handling( at the moment up to 10 chars are accepted). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileCharBreakS | 1.3.6.1.4.1.164.8.2.1.1.1.30 | ||
| This entry specifies the decimal value of the character that will be interpreted as an additional break signal by the PAD. A value of zero indicates no break character. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileCharSuppressS | 1.3.6.1.4.1.164.8.2.1.1.1.31 | ||
| This entry specifies the decimal value of the character that will toggle echo suppression in the PAD. A value of zero indicates that echo suppression is only controlled by radSPSProfileEcho. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileCharSubsS | 1.3.6.1.4.1.164.8.2.1.1.1.32 | ||
| This entry specifies the decimal value of the character that will be echoed instead of the character received from the user's DTE. A zero value indicates that no character is echoed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileFormFeedPadS | 1.3.6.1.4.1.164.8.2.1.1.1.33 | ||
| This entry specifies the number of padding (NUL) characters that will be automatically sent after the form feed character. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileInactivityS | 1.3.6.1.4.1.164.8.2.1.1.1.34 | ||
| This entry specifies the number of minutes after which the PAD will forward the accumulated data and clear the call. A zero value indicates no disconnection on inactivity. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileOptionsS | 1.3.6.1.4.1.164.8.2.1.1.1.35 | ||
| This entry defines several options to control the profile. The value is a sum of values (powers of two), where each value in the sum represents an option . The values that may be included in the sum and their meanings are: 0 No options 1 Remote set of local X.3 parameters through X.29 is disabled 2 Add sub address to call request 4 Don't use protocol ID in user data field. 8 SPRINT NUI format 16 More bit is set when the edit buffer is full 32 Extended error message 64 Discard connect extended service signal 128 enable connect by typing the address w/out a command | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileClrTimerS | 1.3.6.1.4.1.164.8.2.1.1.1.36 | ||
| This entry specifies the number of minutes after which a call is cleared. If the parameter value is 0, there is no disconnection timer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileSubAddInCUDS | 1.3.6.1.4.1.164.8.2.1.1.1.37 | ||
| This entry defines the number of digits for the subaddress in CUD. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..5 | ||
| pktSwchProfileStatusS | 1.3.6.1.4.1.164.8.2.1.1.1.38 | ||
| The status of this profile. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchProfileATable | 1.3.6.1.4.1.164.8.2.1.2 | ||
| The Profile Table defines the profiles that the PS can use to configure a channel. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchProfileAEntry | |||
| pktSwchProfileAEntry | 1.3.6.1.4.1.164.8.2.1.2.1 | ||
| Defines the contents of each line in the Profile Table. | |||
| OBJECT-TYPE | |||
| PktSwchProfileAEntry | |||
| pktSwchProfileNumberA | 1.3.6.1.4.1.164.8.2.1.2.1.1 | ||
| The number by which a profile is identified. This is also used as the index for the profile table. The maximum profile number is 200. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchProfileRecallCharA | 1.3.6.1.4.1.164.8.2.1.2.1.2 | ||
| The character specified by this entry is used to escape from the data transfer mode and enter the PAD command mode. The integer values have the following meanings: (0) PAD recall is not possible (1) The PAD recall character is DLE (2) to (126) The PAD recall character is specified by the user by entering its ASCII code. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchProfileEchoA | 1.3.6.1.4.1.164.8.2.1.2.1.3 | ||
| This determines if an echo of the input characters is retured to the DTE. The options are either 'echo enabled' or 'no echo'. | |||
| OBJECT-TYPE | |||
| INTEGER | echEn(1), noEch(2) | ||
| pktSwchProfileDataForwCharA | 1.3.6.1.4.1.164.8.2.1.2.1.4 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) used as a data forwarding character. The data forwarding characters are used to instruct the PAD to complete the assembly of and to forward a packet containing the data accumulated up to the reception of such a character. The values that may be included in the sum and their meanings are: 0 Data forwarding characters are not used 1 Alpha-numeric characters (A to Z, a to z, 0 to 9, inclusive) 2 Character CR 4 Characters ESC, BEL, ENQ, ACK 8 Characters DEL, CAN, DC2 16 Characters EOT, ETX 32 Characters HT, LF, VT, FF 64 All the other characters in colums 0 and 1 of IA5 and not listed above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileIdleTimerA | 1.3.6.1.4.1.164.8.2.1.2.1.5 | ||
| Packets will be forwarded when the idle timer expires. The idle time interval is specified as a multiple of 50 milliseconds. The multiple is given by the parameter value. For example, a value of 60 sets an interval of 3 seconds. If the parameter value is 0, no forwarding occurs after the idle condition. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileDevFlowContA | 1.3.6.1.4.1.164.8.2.1.2.1.6 | ||
| This parameter determines whether or not the PAD uses software flow control for the attached device. The options are either (1) PAD uses flow control during data transfer mode, (2) PAD uses flow control both in the data transfer mode and in the command mode, or (255) PAD does not use flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | trans(1), transAndCom(2), noFlow(255) | ||
| pktSwchProfileServSigA | 1.3.6.1.4.1.164.8.2.1.2.1.7 | ||
| This parameter is used to instruct the PAD whether to transfer PAD service signals and the PAD prompt to the local DTE in standard format. The options are (1) PAD service signals are transmitted to the DTE using the standard format, (4) The PAD prompt is transmitted using the standard format, (5) PAD service signals and the PAD prompt are transmitted in the standard format, or (255) No PAD service signals are transmitted to the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | serv(1), prompt(4), servAndPrompt(5), noSig(255) | ||
| pktSwchProfileBreakA | 1.3.6.1.4.1.164.8.2.1.2.1.8 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a PAD operation on receipt of the break signal from the DTE. The values that may be included in the sum and their meanings are: 0 Nothing 1 Send interrupt packet to network 2 Send RESET packet to network 4 Send and 'indication of break' message 8 Escape from data transfer mode 16 Discard output data waiting to be sent to the DTE . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..31 | ||
| pktSwchProfileDiscOutA | 1.3.6.1.4.1.164.8.2.1.2.1.9 | ||
| This parameter instructs the PAD whether to forward the user sequences included in data packets to the local DTE or discard them. The options are (1) discard output or (2) normal data delivery. If the value of radSPSProfileBreak is 21, the value of pktSwchProfileDiscOut is automatically set to (1) when a break signal is received. | |||
| OBJECT-TYPE | |||
| INTEGER | discOut(1), normal(2) | ||
| pktSwchProfileCRPaddingA | 1.3.6.1.4.1.164.8.2.1.2.1.10 | ||
| This parameter specifies the number of padding characters to be added after a carriage return character is transmitted to the local DTE. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineFoldA | 1.3.6.1.4.1.164.8.2.1.2.1.11 | ||
| This parameter specifies the maximum number of characters to be inserted before the format effector. If the value is zero, there is no insertion of a format effector (line folding). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileSpeedA | 1.3.6.1.4.1.164.8.2.1.2.1.12 | ||
| This parameter determines the rate of data transmission to and from the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21) | ||
| pktSwchProfilePadFlowContA | 1.3.6.1.4.1.164.8.2.1.2.1.13 | ||
| This determines whether or not the terminal can exercise flow control over the PAD. The options are either 'device can exercise flow control' or 'device cannot exercise flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | flowCont(1), noFlowCont(2) | ||
| pktSwchProfileLineFeedInsertA | 1.3.6.1.4.1.164.8.2.1.2.1.14 | ||
| This parameter indicates when there is a line feed insertion after CR. The options are (1) Insert line feed after transmission of CR to the DTE, (2) Insert line feed after receipt of CR from the DTE, (4) Insert line feed after echoing a CR character to the DTE, (5) Combination of (1) and (4), (6) Insert line feed after any CR to the DTE (combination of (2) and (4)), (7) Combination of (1), (2), and (4), or (255) No line feed insertion. | |||
| OBJECT-TYPE | |||
| INTEGER | afterCR(1), recCR(2), echoCR(4), onePlusFour(5), twoPlusFour(6), oneTwoFour(7), noFeed(255) | ||
| pktSwchProfileLineFeedPadA | 1.3.6.1.4.1.164.8.2.1.2.1.15 | ||
| This parameter specifies the number of padding characters to be added after a line feed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileEditingA | 1.3.6.1.4.1.164.8.2.1.2.1.16 | ||
| This parameter specifies the editing capabilities available in the data transfer mode. Editing is always possible when the PAD is in the command mode. The options are (1) Command editing in the data trasfer mode is enabled or (2) No command editing in the data transfer mode. | |||
| OBJECT-TYPE | |||
| INTEGER | edit(1), noEdit(2) | ||
| pktSwchProfileCharDelA | 1.3.6.1.4.1.164.8.2.1.2.1.17 | ||
| This parameter specifies the character delete, which is one character from IA5. The default selection is 127 (character DEL). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineDelA | 1.3.6.1.4.1.164.8.2.1.2.1.18 | ||
| This parameter specifies the line delete, which is one character from IA5. The default selection is 24 (character CAN). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileLineDispA | 1.3.6.1.4.1.164.8.2.1.2.1.19 | ||
| This entry specifies the line display character, which is one character from IA5. The default selection is 18 (character DC2). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileEditServSigA | 1.3.6.1.4.1.164.8.2.1.2.1.20 | ||
| This entry specifies the editing PAD service signals. The integer values have the following meanings: (0) No editing PAD service signals (1) Editing PAD service signals for printing terminals (2) Editing PAD service signals for display terminals (3) to (126) Editing PAD service signals using the desired character from IA5. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchProfileEchomaskA | 1.3.6.1.4.1.164.8.2.1.2.1.21 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) included in the echo mask. The characters in the echo mask are not echoed to the DTE when PAD echo is enabled. The values that may be included in the sum and their meanings are: 0 No echo mask (all the characters are echoed) 1 No echo of character CR 2 No echo of character LF 4 No echo of characters VT, HT, FF 8 No echo of characters BEL, BS 16 No echo of characters ESC, ENQ 32 No echo of characters ACK, NAK, STX, SOH, EOT, ETB, ETX 64 No echo of the editing characters selected by radSPSProfileCharDel, radSPSProfileLineDel, and radSPSProfileLineDisp 128 No echo of the DEL character and of all the other characters in the range of ASCII 00 through 31 not mentioned above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileParTreatA | 1.3.6.1.4.1.164.8.2.1.2.1.22 | ||
| This entry controls the generation of parity bits in the data sent to the local DTE and the checking of the parity bit when generated by the local DTE. The options are (1) parity checking is enabled, (2) parity generation is enabled, (3) parity checking and generation are enabled, or (255) no parity checking nor parity generation. | |||
| OBJECT-TYPE | |||
| INTEGER | parCheck(1), parGen(2), checkAndGen(3), noPar(255) | ||
| pktSwchProfilePageWaitA | 1.3.6.1.4.1.164.8.2.1.2.1.23 | ||
| This entry specifies the number of line feed characters counted by the PAD before the page wait condition is entered. If the value is zero, page wait is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileBitsPerCharA | 1.3.6.1.4.1.164.8.2.1.2.1.24 | ||
| The number of data bits per character supported by the PAD. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..8 | ||
| pktSwchProfileDvParityA | 1.3.6.1.4.1.164.8.2.1.2.1.25 | ||
| This entry selects the type of parity to be checked and or generated by the PAD when radSPSProfileParTreat is a value other than 255. The options are (1) space parity, (2) mark parity, (3) even parity, (4) odd parity, or (255) no parity. | |||
| OBJECT-TYPE | |||
| INTEGER | space(1), mark(2), even(3), odd(4), none(255) | ||
| pktSwchProfileStopBitsA | 1.3.6.1.4.1.164.8.2.1.2.1.26 | ||
| This entry indicates the number of stop bits per character supported by the PAD. The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), oneAndHalf(3) | ||
| pktSwchProfileSpecFlowA | 1.3.6.1.4.1.164.8.2.1.2.1.27 | ||
| This entry is used to define additional flow control possiblilites. The options are either (1) Flow control by means fo the terminal DTR line or (2) No special flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | spec(1), noSpec(2) | ||
| pktSwchProfileCountFwdA | 1.3.6.1.4.1.164.8.2.1.2.1.28 | ||
| This entry can be used to instruct the PAD to complete the assembly of a packet and to forward it after the specifed number of characters has been received. If the value is zero, count forwarding is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileEscDelayA | 1.3.6.1.4.1.164.8.2.1.2.1.29 | ||
| This entry can be used to instruct the PAD whether to delay the forwarding of a data packet when an escape character is detected in the data stream and to determine the required delay. The packet forwarding is delayed until the specified number of characters is received after the escape character. A value of zero indicates no special handling. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pktSwchProfileCharBreakA | 1.3.6.1.4.1.164.8.2.1.2.1.30 | ||
| This entry specifies the decimal value of the character that will be interpreted as an additional break signal by the PAD. A value of zero indicates no break character. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileCharSuppressA | 1.3.6.1.4.1.164.8.2.1.2.1.31 | ||
| This entry specifies the decimal value of the character that will toggle echo suppression in the PAD. A value of zero indicates that echo suppression is only controlled by radSPSProfileEcho. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileCharSubsA | 1.3.6.1.4.1.164.8.2.1.2.1.32 | ||
| This entry specifies the decimal value of the character that will be echoed instead of the character received from the user's DTE. A zero value indicates that no character is echoed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileFormFeedPadA | 1.3.6.1.4.1.164.8.2.1.2.1.33 | ||
| This entry specifies the number of padding (NUL) characters that will be automatically sent after the form feed character. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchProfileInactivityA | 1.3.6.1.4.1.164.8.2.1.2.1.34 | ||
| This entry specifies the number of minutes after which the PAD will forward the accumulated data and clear the call. A zero value indicates no disconnection on inactivity. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileOptionsA | 1.3.6.1.4.1.164.8.2.1.2.1.35 | ||
| This entry defines several options to control the profile. The value is a sum of values (powers of two), where each value in the sum represents an option . The values that may be included in the sum and their meanings are: 0 No options 1 Remote set of local X.3 parameters though X.29 is disabled 2 Add sub address to call request 4 Don't use protocol ID in user data field. 8 SPRINT NUI format 16 More bit is set when the edit buffer is full 32 Extended error message 64 Discard connect extended service signal 128 enable connect by typing the address w/out a command | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileClrTimerA | 1.3.6.1.4.1.164.8.2.1.2.1.36 | ||
| This entry specifies the number of minutes after which a call is cleared. If the parameter value is 0, there is no disconnection timer. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchProfileSubAddInCUDA | 1.3.6.1.4.1.164.8.2.1.2.1.37 | ||
| This entry defines the number of digits for the subaddress in CUD. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..5 | ||
| pktSwchChannel | 1.3.6.1.4.1.164.8.2.2 | ||
| OBJECT IDENTIFIER | |||
| pktSwchChannelSTable | 1.3.6.1.4.1.164.8.2.2.1 | ||
| The Scratch Channel Table defines the channels configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchChannelSEntry | |||
| pktSwchChannelSEntry | 1.3.6.1.4.1.164.8.2.2.1.1 | ||
| Defines the contents of each line in the Scratch Channel Table. | |||
| OBJECT-TYPE | |||
| PktSwchChannelSEntry | |||
| pktSwchChannelIfIndexS | 1.3.6.1.4.1.164.8.2.2.1.1.1 | ||
| This is used as the index for the channel table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelNumberS | 1.3.6.1.4.1.164.8.2.2.1.1.2 | ||
| The number by which a channel is identified. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..1224 | ||
| pktSwchChannelProfileS | 1.3.6.1.4.1.164.8.2.2.1.1.3 | ||
| The profile that the channel uses for command mode operations. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchChannelOutCallProfileS | 1.3.6.1.4.1.164.8.2.2.1.1.4 | ||
| The number of the profile that will be used during an outgoing call on the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelInCallProfileS | 1.3.6.1.4.1.164.8.2.2.1.1.5 | ||
| The number of the profile that will be used during an incoming call on the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelRemoteProfileS | 1.3.6.1.4.1.164.8.2.2.1.1.6 | ||
| The number of the profile that will be downloaded to the remote PAD at the beginning of a new call. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelAutocallIdS | 1.3.6.1.4.1.164.8.2.2.1.1.7 | ||
| Selects the mnemonic (call ID) to be used as the first alternative. A value of zero indicates that the autocall function is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelAlterAutocallIdS | 1.3.6.1.4.1.164.8.2.2.1.1.8 | ||
| Selects the alternate mnemonic for the autocall function. A value of zero indicates that the alternate destination is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelAutocallRetriesS | 1.3.6.1.4.1.164.8.2.2.1.1.9 | ||
| The number of autocall retries if the autocall setup request is rejected with a busy cause. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelAutocallIntervalS | 1.3.6.1.4.1.164.8.2.2.1.1.10 | ||
| The interval in seconds between consecutive autocall retries. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelCallAliasS | 1.3.6.1.4.1.164.8.2.2.1.1.11 | ||
| The alias to be sent after the call is set up. A value of zero indicates that alias sending is disabled. The aliases are configured on the Alias Table. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchChannelSubAddress1S | 1.3.6.1.4.1.164.8.2.2.1.1.12 | ||
| The first subaddress for the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelSubAddress2S | 1.3.6.1.4.1.164.8.2.2.1.1.13 | ||
| The second subaddress for the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelNUISEntry | 1.3.6.1.4.1.164.8.2.2.1.1.14 | ||
| The number corresponding to the NUI information to be sent. This number is the same as the pktSwchNuiGroupId. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchChannelClearTimerS | 1.3.6.1.4.1.164.8.2.2.1.1.15 | ||
| Time limitation for an open session. A value of zero indicates that the Clear timer is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelOptionsS | 1.3.6.1.4.1.164.8.2.2.1.1.16 | ||
| This controls the use of gneral non-correlated channel options. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 HW signal is checked 2 Auto call after clear 4 Auto call after 8 DCD is ON, only in DATA TRANSFER mode 16 Charging Info Facility 32 Auto call if HW signal is set 64 Accept calls even if HW signal is is OFF 128 A transparent channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchChannelClear | 1.3.6.1.4.1.164.8.2.2.1.1.17 | ||
| The Clearing Channel operation disconnects all sessions | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), clear(2) | ||
| pktSwchChannelCopyTo | 1.3.6.1.4.1.164.8.2.2.1.1.18 | ||
| The destination channel number, to which the Copy is performed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelCopyToWMask | 1.3.6.1.4.1.164.8.2.2.1.1.19 | ||
| The destination channel number, to which the Copy with Mask is performed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelCopyMask | 1.3.6.1.4.1.164.8.2.2.1.1.20 | ||
| The selected configuration parameters to be copied from the source channel to the target channels. The value is a sum of values (powers of two), where each value in the sum represents a selected parameter that is not copied. The values that may be included in the sum and their meanings are: 0 Copy all. 1 Do not copy Profile. 2 Do not copy OutCallProfile. 4 Do not copy InCallProfile. 8 Do not copy RemoteProfile. 16 Do not copy AutocallId. 32 Do not copy AlterCallId. 64 Do not copy AutoCallRetries. 128 Do not copy AutoCallInterval. 256 Do not copy CallAlias. 512 Do not copy SubAddress1. 1024 Do not copy SubAddress2. 2048 Do not copy NUIEntry. 4096 Do not copy ClearTimer. 8192 Do not copy Options. XXX - Any combination of the above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..16383 | ||
| pktSwchChannelATable | 1.3.6.1.4.1.164.8.2.2.2 | ||
| The Active Channel Table defines the channels configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchChannelAEntry | |||
| pktSwchChannelAEntry | 1.3.6.1.4.1.164.8.2.2.2.1 | ||
| Defines the contents of each line in the Active Channel Table. | |||
| OBJECT-TYPE | |||
| PktSwchChannelAEntry | |||
| pktSwchChannelIfIndexA | 1.3.6.1.4.1.164.8.2.2.2.1.1 | ||
| This is used as the index for the channel table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelNumberA | 1.3.6.1.4.1.164.8.2.2.2.1.2 | ||
| The number by which a channel is identified. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..288 | ||
| pktSwchChannelProfileA | 1.3.6.1.4.1.164.8.2.2.2.1.3 | ||
| The profile that the channel uses for command mode operations. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelOutCallProfileA | 1.3.6.1.4.1.164.8.2.2.2.1.4 | ||
| The number of the profile that is used during an outgoing call on the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelInCallProfileA | 1.3.6.1.4.1.164.8.2.2.2.1.5 | ||
| The number of the profile that is used during an incoming call on the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelRemoteProfileA | 1.3.6.1.4.1.164.8.2.2.2.1.6 | ||
| The number of the profile that is downloaded to the remote PAD at the beginning of a new call. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelAutocallIdA | 1.3.6.1.4.1.164.8.2.2.2.1.7 | ||
| Selects the mnemonic (call ID) to be used as the first alternative. A value of zero indicates that the autocall function is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelAlterAutocallIdA | 1.3.6.1.4.1.164.8.2.2.2.1.8 | ||
| Selects the alternate mnemonic for the autocall function. A value of zero indicates that the alternate destination is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelAutocallRetriesA | 1.3.6.1.4.1.164.8.2.2.2.1.9 | ||
| The number of autocall retrues if the autocall setup request is rejected with a busy cause. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelAutocallIntervalA | 1.3.6.1.4.1.164.8.2.2.2.1.10 | ||
| The interval in seconds between consecutive autocall retries. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelCallAliasA | 1.3.6.1.4.1.164.8.2.2.2.1.11 | ||
| The alias to be sent after the call is set up. A value of zero indicates that alias sending is disabled. The aliases are configured on the Alias Table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelSubAddress1A | 1.3.6.1.4.1.164.8.2.2.2.1.12 | ||
| The first subaddress for the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelSubAddress2A | 1.3.6.1.4.1.164.8.2.2.2.1.13 | ||
| The second subaddress for the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelNUIAEntry | 1.3.6.1.4.1.164.8.2.2.2.1.14 | ||
| The number corresponding to the NUI information to be sent. This number is the same as the pktSwchNuiIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelClearTimerA | 1.3.6.1.4.1.164.8.2.2.2.1.15 | ||
| Time limitation for an open session. A value of zero indicates that the Clear timer is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchChannelOptionsA | 1.3.6.1.4.1.164.8.2.2.2.1.16 | ||
| This controls the use of general non-correlated channel options. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 RTS line checked 2 Auto call after clear 4 Auto call after 8 DCD is ON, only in DATA TRANSFER mode. 16 Charging Info Facility 32 Auto call if HW signal is set 64 Accept calls even if HW signal is is OFF 128 A transparent channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCallId | 1.3.6.1.4.1.164.8.2.3 | ||
| OBJECT IDENTIFIER | |||
| pktSwchCallIdSTable | 1.3.6.1.4.1.164.8.2.3.1 | ||
| The Call ID Table S defines the Scratch Call IDs configured on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchCallIdSEntry | |||
| pktSwchCallIdSEntry | 1.3.6.1.4.1.164.8.2.3.1.1 | ||
| Defines the contents of each line in the Scratch CallId Table. | |||
| OBJECT-TYPE | |||
| PktSwchCallIdSEntry | |||
| pktSwchCallIdNumberS | 1.3.6.1.4.1.164.8.2.3.1.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchCallIdMnemonicS | 1.3.6.1.4.1.164.8.2.3.1.1.2 | ||
| The mnemonic for this call ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchCallIdAddressS | 1.3.6.1.4.1.164.8.2.3.1.1.3 | ||
| The address for this call ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchCallIdStatusS | 1.3.6.1.4.1.164.8.2.3.1.1.4 | ||
| The status of this Call ID table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchCallIdATable | 1.3.6.1.4.1.164.8.2.3.2 | ||
| The Call ID Table A defines the Active Call IDs configured on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchCallIdAEntry | |||
| pktSwchCallIdAEntry | 1.3.6.1.4.1.164.8.2.3.2.1 | ||
| Defines the contents of each line in the Active CallId Table. | |||
| OBJECT-TYPE | |||
| PktSwchCallIdAEntry | |||
| pktSwchCallIdNumberA | 1.3.6.1.4.1.164.8.2.3.2.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchCallIdMnemonicA | 1.3.6.1.4.1.164.8.2.3.2.1.2 | ||
| The mnemonic for this call ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchCallIdAddressA | 1.3.6.1.4.1.164.8.2.3.2.1.3 | ||
| The address for this call ID. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchAlias | 1.3.6.1.4.1.164.8.2.4 | ||
| OBJECT IDENTIFIER | |||
| pktSwchAliasSTable | 1.3.6.1.4.1.164.8.2.4.1 | ||
| The Alias Table defines the aliases configured on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchAliasSEntry | |||
| pktSwchAliasSEntry | 1.3.6.1.4.1.164.8.2.4.1.1 | ||
| Defines the contents of each line in the Alias Table. | |||
| OBJECT-TYPE | |||
| PktSwchAliasSEntry | |||
| pktSwchAliasNumberS | 1.3.6.1.4.1.164.8.2.4.1.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchAliasValueS | 1.3.6.1.4.1.164.8.2.4.1.1.2 | ||
| The alias is defined using up to 64 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| pktSwchAliasStatusS | 1.3.6.1.4.1.164.8.2.4.1.1.3 | ||
| The status of this Alias table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchAliasATable | 1.3.6.1.4.1.164.8.2.4.2 | ||
| The Alias Table defines the aliases configured on the device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchAliasAEntry | |||
| pktSwchAliasAEntry | 1.3.6.1.4.1.164.8.2.4.2.1 | ||
| Defines the contents of each line in the Alias Table. | |||
| OBJECT-TYPE | |||
| PktSwchAliasAEntry | |||
| pktSwchAliasNumberA | 1.3.6.1.4.1.164.8.2.4.2.1.1 | ||
| The index of this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchAliasValueA | 1.3.6.1.4.1.164.8.2.4.2.1.2 | ||
| The alias is defined using up to 64 characters. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..64) | ||
| pktSwchAsyncStatTable | 1.3.6.1.4.1.164.8.2.5 | ||
| The AsyncStat Table includes status information and statistics provided by the PS on the async channels. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchAsyncStatEntry | |||
| pktSwchAsyncStatEntry | 1.3.6.1.4.1.164.8.2.5.1 | ||
| Defines the contents of each line in the Async Stat Table. | |||
| OBJECT-TYPE | |||
| PktSwchAsyncStatEntry | |||
| pktSwchAsyncIfIndex | 1.3.6.1.4.1.164.8.2.5.1.1 | ||
| An index for the table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncChannelNumber | 1.3.6.1.4.1.164.8.2.5.1.2 | ||
| The channel to which this entry applies. This value is the same as the pktSwchChannelNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncConnectionStatus | 1.3.6.1.4.1.164.8.2.5.1.3 | ||
| The connection status of the channel is either FREE or ENG (engaged). | |||
| OBJECT-TYPE | |||
| INTEGER | engaged(1), free(2) | ||
| pktSwchAsyncNumLogChannels | 1.3.6.1.4.1.164.8.2.5.1.4 | ||
| The number of active logical channels used by the asynchronous channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncNumActSessions | 1.3.6.1.4.1.164.8.2.5.1.5 | ||
| The number of active sessions opened by this asynchronous channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncAutocallId | 1.3.6.1.4.1.164.8.2.5.1.6 | ||
| Indicates whether the channel has been configured to use the autocall function and what is the call ID. NONE means that the channel is not configured for autocall. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncRTSStatus | 1.3.6.1.4.1.164.8.2.5.1.7 | ||
| Shows the status of the RTS line of the asynchronous channel. OFF indicates that the RTS line is not active, ON indicates that it is active, and UNUSED indicates that the channel PAD is programmed to disregard the state of the RTS line. | |||
| OBJECT-TYPE | |||
| INTEGER | unused(1), off(2), on(3) | ||
| pktSwchAsyncBuffToNet | 1.3.6.1.4.1.164.8.2.5.1.8 | ||
| The number of data buffers currently used by the transmit direction of the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncBuffToUser | 1.3.6.1.4.1.164.8.2.5.1.9 | ||
| The number of data buffers currently used by the receive direction of the channel. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncTxXoff | 1.3.6.1.4.1.164.8.2.5.1.10 | ||
| The current state of software flow control in the transmit direction. NO indicates that traffic flow is enabled. YES indicates that traffic flow from the user's DTE to the device channel has been interrupted by sending the X-OFF character to the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| pktSwchAsyncRxXoff | 1.3.6.1.4.1.164.8.2.5.1.11 | ||
| The current state of software flow control in the receive direction. NO indicates that traffic flow is enabled. YES indicates that traffic flow to the user's DTE from the device channel has been interrupted by means of the X-OFF character. | |||
| OBJECT-TYPE | |||
| INTEGER | no(1), yes(2) | ||
| pktSwchAsyncBuffOutstand | 1.3.6.1.4.1.164.8.2.5.1.12 | ||
| Indicates the number of buffers which were sent to the async user but weren't yet freed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncChannelMode | 1.3.6.1.4.1.164.8.2.5.1.13 | ||
| The channel mode is either X28 COMMAND or DATA TRANSFER. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), activeLink(2), x28command(3), dataTransfer(4) | ||
| pktSwchAsyncRunProTable | 1.3.6.1.4.1.164.8.2.6 | ||
| The AsyncRunPro Table includes status information and statistics provided by the PS on the async channels. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchAsyncRunProEntry | |||
| pktSwchAsyncRunProEntry | 1.3.6.1.4.1.164.8.2.6.1 | ||
| Defines the contents of each line in the Async RunPro Table. | |||
| OBJECT-TYPE | |||
| PktSwchAsyncRunProEntry | |||
| pktSwchAsyncRunProIfIndex | 1.3.6.1.4.1.164.8.2.6.1.1 | ||
| An index for the table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncRunProChannelNumber | 1.3.6.1.4.1.164.8.2.6.1.2 | ||
| The channel to which this entry applies. This value is the same as the pktSwchChannelNumber. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchAsyncRunProRecallChar | 1.3.6.1.4.1.164.8.2.6.1.3 | ||
| The character specified by this entry is used to escape from the data transfer mode and enter the PAD command mode. The integer values have the following meanings: (0) PAD recall is not possible (1) The PAD recall character is DLE (2) to (126) The PAD recall character is specified by the user by entering its ASCII code. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchAsyncRunProEcho | 1.3.6.1.4.1.164.8.2.6.1.4 | ||
| This determines if an echo of the input characters is retured to the DTE. The options are either 'echo enabled' or 'no echo'. | |||
| OBJECT-TYPE | |||
| INTEGER | echEn(1), noEch(2) | ||
| pktSwchAsyncRunProDataForwChar | 1.3.6.1.4.1.164.8.2.6.1.5 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) used as a data forwarding character. The data forwarding characters are used to instruct the PAD to complete the assembly of and to forward a packet containing the data accumulated up to the reception of such a character. The values that may be included in the sum and their meanings are: 0 Data forwarding characters are not used 1 Alpha-numeric characters (A to Z, a to z, 0 to 9, inclusive) 2 Character CR 4 Characters ESC, BEL, ENQ, ACK 8 Characters DEL, CAN, DC2 16 Characters EOT, ETX 32 Characters HT, LF, VT, FF 64 All the other characters in colums 0 and 1 of IA5 and not listed above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchAsyncRunProIdleTimer | 1.3.6.1.4.1.164.8.2.6.1.6 | ||
| Packets will be forwarded when the idle timer expires. The idle time interval is specified as a multiple of 50 milliseconds. The multiple is given by the parameter value. For example, a value of 60 sets an interval of 3 seconds. If the parameter value is 0, no forwarding occurs after the idle condition. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchAsyncRunProDevFlowCont | 1.3.6.1.4.1.164.8.2.6.1.7 | ||
| This parameter determines whether or not the PAD uses software flow control for the attached device. The options are either (1) PAD uses flow control during data transfer mode, (2) PAD uses flow control both in the data transfer mode and in the command mode, or (255) PAD does not use flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | trans(1), transAndCom(2), noFlow(255) | ||
| pktSwchAsyncRunProServSig | 1.3.6.1.4.1.164.8.2.6.1.8 | ||
| This parameter is used to instruct the PAD whether to transfer PAD service signals and the PAD prompt to the local DTE in standard format. The options are (1) PAD service signals are transmitted to the DTE using the standard format, (4) The PAD prompt is transmitted using the standard format, (5) PAD service signals and the PAD prompt are transmitted in the standard format, or (255) No PAD service signals are transmitted to the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | serv(1), prompt(4), servAndPrompt(5), noSig(255) | ||
| pktSwchAsyncRunProBreak | 1.3.6.1.4.1.164.8.2.6.1.9 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a PAD operation on receipt of the break signal from the DTE. The values that may be included in the sum and their meanings are: 0 Nothing 1 Send interrupt packet to network 2 Send RESET packet to network 4 Send and 'indication of break' message 8 Escape from data transfer mode 16 Discard output data waiting to be sent to the DTE . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..31 | ||
| pktSwchAsyncRunProDiscOut | 1.3.6.1.4.1.164.8.2.6.1.10 | ||
| This parameter instructs the PAD whether to forward the user sequences included in data packets to the local DTE or discard them. The options are (1) discard output or (2) normal data delivery. If the value of radSPSProfileBreak is 21, the value of pktSwchAsyncRunProDiscOut is automatically set to (1) when a break signal is received. | |||
| OBJECT-TYPE | |||
| INTEGER | discOut(1), normal(2) | ||
| pktSwchAsyncRunProCRPPadding | 1.3.6.1.4.1.164.8.2.6.1.11 | ||
| This parameter specifies the number of padding characters to be added after a carriage return character is transmitted to the local DTE. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchAsyncRunProLineFold | 1.3.6.1.4.1.164.8.2.6.1.12 | ||
| This parameter specifies the maximum number of characters to be inserted before the format effector. If the value is zero, there is no insertion of a format effector (line folding). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchAsyncRunProSpeed | 1.3.6.1.4.1.164.8.2.6.1.13 | ||
| This parameter determines the rate of data transmission to and from the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21) | ||
| pktSwchAsyncRunProPadFlowCont | 1.3.6.1.4.1.164.8.2.6.1.14 | ||
| This determines whether or not the terminal can exercise flow control over the PAD. The options are either 'device can exercise flow control' or 'device cannot exercise flow control. | |||
| OBJECT-TYPE | |||
| INTEGER | flowCont(1), noFlowCont(2) | ||
| pktSwchAsyncRunProLineFeedInsert | 1.3.6.1.4.1.164.8.2.6.1.15 | ||
| This parameter indicates when there is a line feed insertion after CR. The options are (1) Insert line feed after transmission of CR to the DTE, (2) Insert line feed after receipt of CR from the DTE, (4) Insert line feed after echoing a CR character to the DTE, (5) Combination of (1) and (4), (6) Insert line feed after any CR to the DTE (combination of (2) and (4)), (7) Combination of (1), (2), and (4), or (255) No line feed insertion. | |||
| OBJECT-TYPE | |||
| INTEGER | afterCR(1), recCR(2), echoCR(4), onePlusFour(5), twoPlusFour(6), oneTwoFour(7), noFeed(255) | ||
| pktSwchAsyncRunProLineFeedPad | 1.3.6.1.4.1.164.8.2.6.1.16 | ||
| This parameter specifies the number of padding characters to be added after a line feed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchAsyncRunProEditing | 1.3.6.1.4.1.164.8.2.6.1.17 | ||
| This parameter specifies the editing capabilities available in the data transfer mode. Editing is always possible when the PAD is in the command mode. The options are (1) Command editing in the data trasfer mode is enabled or (2) No command editing in the data transfer mode. | |||
| OBJECT-TYPE | |||
| INTEGER | edit(1), noEdit(2) | ||
| pktSwchAsyncRunProCharDel | 1.3.6.1.4.1.164.8.2.6.1.18 | ||
| This parameter specifies the character delete, which is one character from IA5. The default selection is 127 (character DEL). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchAsyncRunProLineDel | 1.3.6.1.4.1.164.8.2.6.1.19 | ||
| This parameter specifies the line delete, which is one character from IA5. The default selection is 24 (character CAN). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchAsyncRunProLineDisp | 1.3.6.1.4.1.164.8.2.6.1.20 | ||
| This entry specifies the line display character, which is one character from IA5. The default selection is 18 (character DC2). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..127 | ||
| pktSwchAsyncRunProEditServSig | 1.3.6.1.4.1.164.8.2.6.1.21 | ||
| This entry specifies the editing PAD service signals. The integer values have the following meanings: (0) No editing PAD service signals (1) Editing PAD service signals for printing terminals (2) Editing PAD service signals for display terminals (3) to (126) Editing PAD service signals using the desired character from IA5. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..126 | ||
| pktSwchAsyncRunProEchomask | 1.3.6.1.4.1.164.8.2.6.1.22 | ||
| The value is a sum of values (powers of two), where each value in the sum represents a character (or characters) that is (are) included in the echo mask. The characters in the echo mask are not echoed to the DTE when PAD echo is enabled. The values that may be included in the sum and their meanings are: 0 No echo mask (all the characters are echoed) 1 No echo of character CR 2 No echo of character LF 4 No echo of characters VT, HT, FF 8 No echo of characters BEL, BS 16 No echo of characters ESC, ENQ 32 No echo of characters ACK, NAK, STX, SOH, EOT, ETB, ETX 64 No echo of the editing characters selected by radSPSProfileCharDel, radSPSProfileLineDel, and radSPSProfileLineDisp 128 No echo of the DEL character and of all the other characters in the range of ASCII 00 through 31 not mentioned above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchAsyncRunProParTreat | 1.3.6.1.4.1.164.8.2.6.1.23 | ||
| This entry controls the generation of parity bits in the data sent to the local DTE and the checking of the parity bit when generated by the local DTE. The options are (1) parity checking is enabled, (2) parity generation is enabled, (3) parity checking and generation are enabled, or (255) no parity checking nor parity generation. | |||
| OBJECT-TYPE | |||
| INTEGER | parCheck(1), parGen(2), checkAndGen(3), noPar(255) | ||
| pktSwchAsyncRunProPageWait | 1.3.6.1.4.1.164.8.2.6.1.24 | ||
| This entry specifies the number of line feed characters counted by the PAD before the page wait condition is entered. If the value is zero, page wait is disabled. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchPhyInterfaceTable | 1.3.6.1.4.1.164.8.3 | ||
| The Link Table defines the links configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPhyInterfaceEntry | |||
| pktSwchPhyInterfaceEntry | 1.3.6.1.4.1.164.8.3.1 | ||
| Defines the contents of each line in the Link Table. | |||
| OBJECT-TYPE | |||
| PktSwchPhyInterfaceEntry | |||
| pktSwchPhyInterfaceIfIndex | 1.3.6.1.4.1.164.8.3.1.1 | ||
| The ifIndex identified with this link. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPhyInterfaceProtocolS | 1.3.6.1.4.1.164.8.3.1.2 | ||
| The protocol to be used on this link. Note for PPP: PPP protocol is allowed to be applied on Sync Links (1-3) as well as Async channels (1-24). In order to eliminate ambiguity in the IP destination where a destination of P1 can be used for example for async channel 1 and Sync Link 1, it was decided NOT TO ALLOW configuring PPP on both Sync Link no. 1 and async channel 1. Same for Link 2 and Link 3. | |||
| OBJECT-TYPE | |||
| INTEGER | x25(1), frameRelay(2), hdlc(3), sdlc(4), async(5), stm4(6), stm8(7), stm16(8), stm24(9), mpe(10), bscHpad(11), bscTpad(12), slip(13), ethernet(14), ppp(15) | ||
| pktSwchPhyInterfaceProtocolA | 1.3.6.1.4.1.164.8.3.1.3 | ||
| The protocol currently used on this link. | |||
| OBJECT-TYPE | |||
| INTEGER | x25(1), frameRelay(2), hdlc(3), sdlc(4), async(5), stm4(6), stm8(7), stm16(8), stm24(9), mpe(10), bscHpad(11), bscTpad(12), slip(13), ethernet(14), ppp(15) | ||
| pktSwchPhyInterfaceCopyTo | 1.3.6.1.4.1.164.8.3.1.4 | ||
| The destination interface number, to which the Copy is performed. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPhyInterfaceChanged | 1.3.6.1.4.1.164.8.3.1.5 | ||
| Indicates if the current running protocol is different than the defined protocol | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| pktSwchPhyInterfaceRxBuffInPool | 1.3.6.1.4.1.164.8.3.1.6 | ||
| The free data buffers in the Rx pool per interface | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPhyInterfaceConnector | 1.3.6.1.4.1.164.8.3.1.7 | ||
| The connector type of the interface | |||
| OBJECT-TYPE | |||
| INTEGER | v24(2), v35(3), x21(4), rs530(5), acd(6), mobi(7), u(8), etherUtp(9), noConnector(255) | ||
| pktSwchPhyInterfaceNeighborIp | 1.3.6.1.4.1.164.8.3.1.8 | ||
| The Ip address of the device on the other side of the link. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchPhyInterfaceProtocolStatus | 1.3.6.1.4.1.164.8.3.1.9 | ||
| The status of the Interface Protocol row in the Table. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchPhyInterfaceTestCmd | 1.3.6.1.4.1.164.8.3.1.10 | ||
| START/STOP a test on the current interface. The available tests are: v54Local - Local Analog Loopback (AL), L3 according to ITU-T standard. v54Remote - Remote Digital Loopback(RDL), L2 according to ITU-T standard. For stopping the test, SET the noOp (1) option. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(1), v54Local(2), v54Remote(3) | ||
| pktSwchPhyInterfaceTestTransmittedFrames | 1.3.6.1.4.1.164.8.3.1.11 | ||
| No. of frames which were transmitted from this interface during the TEST. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchPhyInterfaceTestReceivedFrames | 1.3.6.1.4.1.164.8.3.1.12 | ||
| No. of frames which were received on this interface during the TEST. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchPhyInterfaceTestLostFrames | 1.3.6.1.4.1.164.8.3.1.13 | ||
| Percentage of the frames which were lost during the TEST. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchx25 | 1.3.6.1.4.1.164.8.4 | ||
| OBJECT IDENTIFIER | |||
| pktSwchLapb | 1.3.6.1.4.1.164.8.4.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchLapbSTable | 1.3.6.1.4.1.164.8.4.1.1 | ||
| The Lapb Table includes statistics and configurable objects provided by the PS that are not included in RFC 1381. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchLapbSEntry | |||
| pktSwchLapbSEntry | 1.3.6.1.4.1.164.8.4.1.1.1 | ||
| Defines the contents of each line in the RAD Lapb Table. | |||
| OBJECT-TYPE | |||
| PktSwchLapbSEntry | |||
| pktSwchLapbLinkNumberS | 1.3.6.1.4.1.164.8.4.1.1.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 and one entry for each link and DLCI if the pktSwchPhyInterfaceProtocol for the link is Frame Relay and the DLCI is defined as using X.25. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLapbInternalClockS | 1.3.6.1.4.1.164.8.4.1.1.1.2 | ||
| The internal clock speed to be used on this LAPB link. If external clock is used, the value is 255. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchLapbLineOptionS | 1.3.6.1.4.1.164.8.4.1.1.1.3 | ||
| The line option to be used on this link. A value of zero indicates no options. A value between 0 and 255 inclusive specifes a time in minutes after which the line will be disconnected if no session is open. The following values have the associated meanings: 256 Dialed line 512 Return to leased line 1024 DTR is ON permanent 2048 DTR is OFF permanent. any valid combination of the above options should be represented as a sum of the corresponding values. Valid combinations are: DTR ON or OFF (but not both). Dialed line options or not applicable. If DTR control is on (256), then all combinations are possible except 1024 and 2048 (which are not possible). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2048 | ||
| pktSwchLapbSegmentSizeS | 1.3.6.1.4.1.164.8.4.1.1.1.4 | ||
| This value is for the use of billing information. The value can be no larger than the maximum packet size. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4096 | ||
| pktSwchLapbXIDS | 1.3.6.1.4.1.164.8.4.1.1.1.5 | ||
| When this parameter is different than zero, this lapb is configured as a V25 bis dialed link. This is the XID entry Index which this dialed link is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLapbAckCounterS | 1.3.6.1.4.1.164.8.4.1.1.1.6 | ||
| This object defines how many frames will be received on the link before the PS will send Acknowledge (RR frame). It is used for Piggy Back Acknowledge (ack within the info frames) and saves traffic on the line. Default value: 1 . | |||
| OBJECT-TYPE | |||
| Integer32 | 1..128 | ||
| pktSwchLapbAckTimerS | 1.3.6.1.4.1.164.8.4.1.1.1.7 | ||
| The Ack Timer defines the maximum time in seconds that the device will wait before sending RR acknowledgment on the received frames. It is used for Piggy Back Acknowledge (ack within the info frames) and saves traffic on the line. Default value: 0 . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchLapbATable | 1.3.6.1.4.1.164.8.4.1.2 | ||
| The Lapb Table includes statistics and configurable objects provided by the PS that are not included in RFC 1381. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchLapbAEntry | |||
| pktSwchLapbAEntry | 1.3.6.1.4.1.164.8.4.1.2.1 | ||
| Defines the contents of each line in the RAD Lapb Table. | |||
| OBJECT-TYPE | |||
| PktSwchLapbAEntry | |||
| pktSwchLapbLinkNumberA | 1.3.6.1.4.1.164.8.4.1.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 and one entry for each link and DLCI if the pktSwchPhyInterfaceProtocol for the link is Frame Relay and theDLCI is defined as using X.25. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLapbInternalClockA | 1.3.6.1.4.1.164.8.4.1.2.1.2 | ||
| The internal clock speed currently used on this LAPB link. If external clock is used, the value is 255. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchLapbLineOptionA | 1.3.6.1.4.1.164.8.4.1.2.1.3 | ||
| The line option currently used on this link. A value of zero indicates no options. A value between 1 and 255 inclusive specifes a time in minutes after which the line will be disconnected if no session is open. The following values have the associated meanings: 256 Dialed line 512 Return to leased line 1024 DTR is ON permanent 2048 DTR is OFF permanent. any valid combination of the above options should be represented as a sum of the corresponding values. Valid combinations are: DTR ON or OFF (but not both). Dialed line options or not applicable. If DTR control is on (256), then all combinations are possible except 1024 and 2048 (which are not possible). | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2048 | ||
| pktSwchLapbSegmentSizeA | 1.3.6.1.4.1.164.8.4.1.2.1.4 | ||
| The current value of the segment size. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4096 | ||
| pktSwchLapbLineProtocol | 1.3.6.1.4.1.164.8.4.1.2.1.5 | ||
| This is the lower level protocol which runs under this lapb interface. | |||
| OBJECT-TYPE | |||
| INTEGER | unknown(1), x25(2), fr(3), isdn(4) | ||
| pktSwchLapbLowerId | 1.3.6.1.4.1.164.8.4.1.2.1.6 | ||
| In case of X.25 over Frame-relay this is the lower level link number. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLapbXIDA | 1.3.6.1.4.1.164.8.4.1.2.1.7 | ||
| When this parameter is different than zero, this lapb is configured as a V25 bis dialed link. This is the XID entry which this dialed link is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLapbTransmittedIFrames | 1.3.6.1.4.1.164.8.4.1.2.1.8 | ||
| The transmitted I frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbReceivedIFrames | 1.3.6.1.4.1.164.8.4.1.2.1.9 | ||
| The received I frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbNSError | 1.3.6.1.4.1.164.8.4.1.2.1.10 | ||
| The number of I frames transmitted out of sequence. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbTransmittedRRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.11 | ||
| The transmitted RR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbReceivedRRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.12 | ||
| The received RR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbTransmittedRNRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.13 | ||
| The transmitted RNR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbReceivedRNRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.14 | ||
| The received RNR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbTransmittedFRMRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.15 | ||
| The transmitted FRMR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbReceivedFRMRFrames | 1.3.6.1.4.1.164.8.4.1.2.1.16 | ||
| The received FRMR frames on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchLapbAckCounterA | 1.3.6.1.4.1.164.8.4.1.2.1.17 | ||
| This object defines how many frames will be received on the link before the PS will send Acknowledge (RR frame). It is used for Piggy Back Acknowledge (ack within the info frames) and saves traffic on the line. Default value: 1 . | |||
| OBJECT-TYPE | |||
| Integer32 | 1..128 | ||
| pktSwchLapbAckTimerA | 1.3.6.1.4.1.164.8.4.1.2.1.18 | ||
| The Ack Timer defines the maximum time in seconds that the device will wait before sending RR acknowledgment on the received frames. It is used for Piggy Back Acknowledge (ack within the info frames) and saves traffic on the line. Default value: 0 . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchPlp | 1.3.6.1.4.1.164.8.4.2 | ||
| OBJECT IDENTIFIER | |||
| pktSwchPlpSTable | 1.3.6.1.4.1.164.8.4.2.1 | ||
| The Scratch Plp Table includes configurable objects provided by the PS that are not included in RFC 1382. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPlpSEntry | |||
| pktSwchPlpSEntry | 1.3.6.1.4.1.164.8.4.2.1.1 | ||
| Defines the contents of each line in the RAD Scratch Plp Table. | |||
| OBJECT-TYPE | |||
| PktSwchPlpSEntry | |||
| pktSwchPlpLinkNumberS | 1.3.6.1.4.1.164.8.4.2.1.1.1 | ||
| The ifIndex of the X.25 interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPlpInCallOptionS | 1.3.6.1.4.1.164.8.4.2.1.1.2 | ||
| The in call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Fast select acceptance - included in RFC 1382 2 Reverse charge acceptance - included in RFC 1382 4 Subaddress in Call User Data field (CUD) 8 Protocol ID (PID) is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchPlpOutCallOptionS | 1.3.6.1.4.1.164.8.4.2.1.1.3 | ||
| The out call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Don't add calling and call addressin call accept packet 2 Network link, call request spread enabled 4 Add source link number to called address 8 Don't change calling address XX - Any combination of the values specified above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchPlpCugSubscriptionS | 1.3.6.1.4.1.164.8.4.2.1.1.4 | ||
| The CUG subscription for the link. | |||
| OBJECT-TYPE | |||
| INTEGER | cug(1), cugOa(2), cugIa(3), cugOaIa(4), noPref(5), noCug(255) | ||
| pktSwchPlpNUIS | 1.3.6.1.4.1.164.8.4.2.1.1.5 | ||
| This is the NUI group which this Plp is part of. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPlpCpyPktSize | 1.3.6.1.4.1.164.8.4.2.1.1.6 | ||
| x25 packet size. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPlpCpyWinSize | 1.3.6.1.4.1.164.8.4.2.1.1.7 | ||
| x25 window size. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPlpATable | 1.3.6.1.4.1.164.8.4.2.2 | ||
| The Active Plp Table includes objects provided by the PS that are not included in RFC 1382. It also includes some packet layer statistics, some of which are defined in RFC 1382, but are not supported there, as the x25StatTable in RFC 1382 is not supported. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPlpAEntry | |||
| pktSwchPlpAEntry | 1.3.6.1.4.1.164.8.4.2.2.1 | ||
| Defines the contents of each line in the RAD Active Plp Table. | |||
| OBJECT-TYPE | |||
| PktSwchPlpAEntry | |||
| pktSwchPlpLinkNumberA | 1.3.6.1.4.1.164.8.4.2.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 and one entry for each link and DLCI if the pktSwchPhyInterfaceProtocol for the link is Frame Relay and theDLCI is defined as using X.25. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchPlpInCallOptionA | 1.3.6.1.4.1.164.8.4.2.2.1.2 | ||
| The current in call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that can be included in the sum and their meanings are: 0 No options 1 Fast select acceptance - included in RFC 1382 2 Reverse charge acceptance - included in RFC 1382 4 Subaddress in Call User Data field (CUD) 8 Protocol ID (PID) is not used. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchPlpOutCallOptionA | 1.3.6.1.4.1.164.8.4.2.2.1.3 | ||
| The out call options for the link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Don't add calling and call addressin call accept packet 2 Network link, call request spread enabled 4 Add source link number to called address 8 Don't change calling address XX - Any combination of the values specified above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..15 | ||
| pktSwchPlpCugSubscriptionA | 1.3.6.1.4.1.164.8.4.2.2.1.4 | ||
| The current CUG subscription for the link. | |||
| OBJECT-TYPE | |||
| INTEGER | cug(1), cugOa(2), cugIa(3), cugOaIa(4), noPref(5), noCug(255) | ||
| pktSwchPlpNUIA | 1.3.6.1.4.1.164.8.4.2.2.1.5 | ||
| This is the NUI group which this Plp is part of. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchStatOutRestarts | 1.3.6.1.4.1.164.8.4.2.2.1.6 | ||
| The number of remotely initiated (including provider initiated) restarts experienced by the PLE excluding the restart associated with bringing up the PLE interface. This only counts restarts received when the PLE already has an established connection with the remove PLE. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchPlaceHolderForFutureUse | 1.3.6.1.4.1.164.8.4.3 | ||
| OBJECT IDENTIFIER | |||
| pktSwchCug | 1.3.6.1.4.1.164.8.4.4 | ||
| OBJECT IDENTIFIER | |||
| pktSwchCugSTable | 1.3.6.1.4.1.164.8.4.4.1 | ||
| The Scratch Cug Table lists the Closed User Groups defined to each X.25 link. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchCugSEntry | |||
| pktSwchCugSEntry | 1.3.6.1.4.1.164.8.4.4.1.1 | ||
| Defines the contents of each line in the Scratch RAD Cug Table. | |||
| OBJECT-TYPE | |||
| PktSwchCugSEntry | |||
| pktSwchCugLinkNumberS | 1.3.6.1.4.1.164.8.4.4.1.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 if the link has CUG options and one entry for each link and DLCI if the pktSwchPhyInterfaceProtocol for the link is Frame Relay and the DLCI is defined as using X.25 if the link has CUG options. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCugIndexS | 1.3.6.1.4.1.164.8.4.4.1.1.2 | ||
| The index of the CUG for a specific link. The lowest indexed CUG is the preferential CUG. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCugNumberS | 1.3.6.1.4.1.164.8.4.4.1.1.3 | ||
| The CUG number for this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCugStatus | 1.3.6.1.4.1.164.8.4.4.1.1.4 | ||
| The status of this CUG table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchCugATable | 1.3.6.1.4.1.164.8.4.4.2 | ||
| The Active Cug Table lists the active Closed User Groups defined to each X.25 link. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchCugAEntry | |||
| pktSwchCugAEntry | 1.3.6.1.4.1.164.8.4.4.2.1 | ||
| Defines the contents of each line in the Active RAD Cug Table. | |||
| OBJECT-TYPE | |||
| PktSwchCugAEntry | |||
| pktSwchCugLinkNumberA | 1.3.6.1.4.1.164.8.4.4.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is X.25 if the link has CUG options and one entry for each link and DLCI if the pktSwchPhyInterfaceProtocol for the link is Frame Relay and theDLCI is defined as using X.25 if the link has CUG options. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCugIndexA | 1.3.6.1.4.1.164.8.4.4.2.1.2 | ||
| The index of the CUG for a specific link. The lowest indexed CUG is the preferential CUG. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchCugNumberA | 1.3.6.1.4.1.164.8.4.4.2.1.3 | ||
| The CUG number for this entry. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLogCh | 1.3.6.1.4.1.164.8.4.5 | ||
| OBJECT IDENTIFIER | |||
| pktSwchLogChAssTable | 1.3.6.1.4.1.164.8.4.5.1 | ||
| These objects contain information about the channel number configuration in an X.25 PLE. These values are the configured values. changes in these values after the interface has started may not be reflected in the operating PLE. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchLogChAssEntry | |||
| pktSwchLogChAssEntry | 1.3.6.1.4.1.164.8.4.5.1.1 | ||
| Entries of pktSwchLogChAssTable. | |||
| OBJECT-TYPE | |||
| PktSwchLogChAssEntry | |||
| pktSwchLogChAssIndex | 1.3.6.1.4.1.164.8.4.5.1.1.1 | ||
| The ifIndex value for the X.25 Interface. | |||
| OBJECT-TYPE | |||
| IfIndexType | |||
| pktSwchLogChAssLIC | 1.3.6.1.4.1.164.8.4.5.1.1.2 | ||
| Lowest Incoming channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChAssHIC | 1.3.6.1.4.1.164.8.4.5.1.1.3 | ||
| Highest Incoming channel. A value of zero indicates no channels in this range. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChAssLTC | 1.3.6.1.4.1.164.8.4.5.1.1.4 | ||
| Lowest Two-way channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChAssHTC | 1.3.6.1.4.1.164.8.4.5.1.1.5 | ||
| Highest Two-way channel. A value of zero indicates no channels in this range. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChAssLOC | 1.3.6.1.4.1.164.8.4.5.1.1.6 | ||
| Lowest outgoing channel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChAssHOC | 1.3.6.1.4.1.164.8.4.5.1.1.7 | ||
| Highest outgoing channel. A value of zero indicates no channels in this range. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..4095 | ||
| pktSwchLogChPartnerTable | 1.3.6.1.4.1.164.8.4.5.2 | ||
| These objects contain information about the partner channel number configuration in an X.25 PLE. These values are the configured values. changes in these values after the interfaces has started may not be reflected in the operating PLE. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchLogChPartnerEntry | |||
| pktSwchLogChPartnerEntry | 1.3.6.1.4.1.164.8.4.5.2.1 | ||
| Entries of pktSwchLogChPartnerTable. | |||
| OBJECT-TYPE | |||
| PktSwchLogChPartnerEntry | |||
| pktSwchLogChPartnerIfIndex | 1.3.6.1.4.1.164.8.4.5.2.1.1 | ||
| The ifIndex value for the Lapb Interface. | |||
| OBJECT-TYPE | |||
| IfIndexType | |||
| pktSwchLogChPartnerLcIndex | 1.3.6.1.4.1.164.8.4.5.2.1.2 | ||
| The Index value for the LCN. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchLogChPartnerProtocol | 1.3.6.1.4.1.164.8.4.5.2.1.3 | ||
| The protocol of the partner. | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), x25(2), hdlc(3), sdlc(4), async(5), mpe(6), ip(7) | ||
| pktSwchLogChPartnerOpIfIndex | 1.3.6.1.4.1.164.8.4.5.2.1.4 | ||
| The ifIndex value for the partner Lapb Interface. | |||
| OBJECT-TYPE | |||
| IfIndexType | |||
| pktSwchLogChPartnerOpLcIndex | 1.3.6.1.4.1.164.8.4.5.2.1.5 | ||
| The Index value for the partner LCN. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlc | 1.3.6.1.4.1.164.8.5 | ||
| OBJECT IDENTIFIER | |||
| pktSwchHdlcSTable | 1.3.6.1.4.1.164.8.5.1 | ||
| The Scratch Hdlc Table contains configuration information for HDLC links | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchHdlcSEntry | |||
| pktSwchHdlcSEntry | 1.3.6.1.4.1.164.8.5.1.1 | ||
| Defines the contents of each line in the RAD Hdlc Table. | |||
| OBJECT-TYPE | |||
| PktSwchHdlcSEntry | |||
| pktSwchHdlcLinkNumberS | 1.3.6.1.4.1.164.8.5.1.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is HDLC. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcDestAddrS | 1.3.6.1.4.1.164.8.5.1.1.2 | ||
| The destination address. It defines the X.25 address on the remote device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchHdlcDestSubAddrS | 1.3.6.1.4.1.164.8.5.1.1.3 | ||
| The destination subaddress. It defines the synchronous link subaddress on the remote device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcRedialTimeoutS | 1.3.6.1.4.1.164.8.5.1.1.4 | ||
| The time interval in seconds between two consecutive connect operations retries. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcRedialRetriesS | 1.3.6.1.4.1.164.8.5.1.1.5 | ||
| This defines how many times the call operation is repeated if the call request has failed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcInactivityS | 1.3.6.1.4.1.164.8.5.1.1.6 | ||
| The amount of time in minutes of inactivity that will cause the session to disconnect. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcX25FacilitiesS | 1.3.6.1.4.1.164.8.5.1.1.7 | ||
| This specifies the X.25 facilities. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Packet size negotiation 2 Window size negotiation 4 Reverse charge. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchHdlcLocalSubaddr1S | 1.3.6.1.4.1.164.8.5.1.1.8 | ||
| The first local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcLocalSubaddr2S | 1.3.6.1.4.1.164.8.5.1.1.9 | ||
| The secondary local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcDestDlciS | 1.3.6.1.4.1.164.8.5.1.1.10 | ||
| The local DLCI which is used for HDLC encapsulation over Frame Relay. Range: 16...991 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcDestPortS | 1.3.6.1.4.1.164.8.5.1.1.11 | ||
| The local port that is used for HDLC encapsulation over Frame Relay. Range: 1...12 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcProtocolS | 1.3.6.1.4.1.164.8.5.1.1.12 | ||
| The HDLC protocol type. | |||
| OBJECT-TYPE | |||
| INTEGER | hdlcOverX25(1), hdlcOverFrRel(2), hdlcOverMpe(3), hdlcReg(4), hdlcOverIp(5) | ||
| pktSwchHdlcFlowContOptionsS | 1.3.6.1.4.1.164.8.5.1.1.13 | ||
| This specifies the type of flow control of the HDLC link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No flow control 1 CTS flow control 2 Clock flow control. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..3 | ||
| pktSwchHdlcBufferFlowControlS | 1.3.6.1.4.1.164.8.5.1.1.14 | ||
| The number of buffers that will be allocated for the HDLC link. Default value is 10 | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchHdlcInternalClockS | 1.3.6.1.4.1.164.8.5.1.1.15 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchHdlcNrzModeS | 1.3.6.1.4.1.164.8.5.1.1.16 | ||
| The data encoding format. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 NRZ 1 NRZI 2 Transmit Idles between frames and control the RTS pin 4 Normal Operation (DCD, CTS lines under automatic control) XX Any combination of the values specified above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchHdlcATable | 1.3.6.1.4.1.164.8.5.2 | ||
| The Active Hdlc Table contains active configuration information for HDLC links | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchHdlcAEntry | |||
| pktSwchHdlcAEntry | 1.3.6.1.4.1.164.8.5.2.1 | ||
| Defines the contents of each line in the RAD Hdlc Table. | |||
| OBJECT-TYPE | |||
| PktSwchHdlcAEntry | |||
| pktSwchHdlcLinkNumberA | 1.3.6.1.4.1.164.8.5.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is HDLC. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcDestAddrA | 1.3.6.1.4.1.164.8.5.2.1.2 | ||
| The destination address. It defines the X.25 address on the remote device. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchHdlcDestSubAddrA | 1.3.6.1.4.1.164.8.5.2.1.3 | ||
| The destination subaddress. It defines the synchronous link subaddress on the remote device. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcRedialTimeoutA | 1.3.6.1.4.1.164.8.5.2.1.4 | ||
| The time interval in seconds between two consecutive connect operations retries. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcRedialRetriesA | 1.3.6.1.4.1.164.8.5.2.1.5 | ||
| This defines how many times the call operation is repeated if the call request has failed. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcInactivityA | 1.3.6.1.4.1.164.8.5.2.1.6 | ||
| The amount of time in minutes of inactivity that will cause the session to disconnect. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchHdlcX25FacilitiesA | 1.3.6.1.4.1.164.8.5.2.1.7 | ||
| This specifies the X.25 facilities. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Packet size negotiation 2 Window size negotiation 4 Reverse charge. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchHdlcLocalSubaddr1A | 1.3.6.1.4.1.164.8.5.2.1.8 | ||
| The first local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcLocalSubaddr2A | 1.3.6.1.4.1.164.8.5.2.1.9 | ||
| The secondary local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..99 | ||
| pktSwchHdlcDestDlciA | 1.3.6.1.4.1.164.8.5.2.1.10 | ||
| The local DLCI which is used for HDLC encapsulation over Frame Relay. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcDestPortA | 1.3.6.1.4.1.164.8.5.2.1.11 | ||
| The local port that is used for HDCL encapsulation over Frame Relay. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcProtocolA | 1.3.6.1.4.1.164.8.5.2.1.12 | ||
| The HDLC protocol type. | |||
| OBJECT-TYPE | |||
| INTEGER | hdlcOverX25(1), hdlcOverFrRel(2), hdlcOverMpe(3), hdlcReg(4), hdlcOverIp(5) | ||
| pktSwchHdlcFlowContOptionsA | 1.3.6.1.4.1.164.8.5.2.1.13 | ||
| This specifies the type of flow control of the HDLC link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No flow control 1 CTS flow control 2 Clock flow control. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..3 | ||
| pktSwchHdlcBufferFlowControlA | 1.3.6.1.4.1.164.8.5.2.1.14 | ||
| The number of buffers that will be allocated for the HDLC link. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchHdlcInternalClockA | 1.3.6.1.4.1.164.8.5.2.1.15 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchHdlcNrzModeA | 1.3.6.1.4.1.164.8.5.2.1.16 | ||
| The data encoding format. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 NRZ 1 NRZI 2 Transmit Idles between frames and control the RTS pin 4 Normal Operation (DCD, CTS lines under automatic control) XX Any combination of the values specified above. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchHdlcConnStatus | 1.3.6.1.4.1.164.8.5.2.1.17 | ||
| The status of the Hdlc session. | |||
| OBJECT-TYPE | |||
| INTEGER | disconnect(1), connect(2), pvc(3) | ||
| pktSwchHdlcSpecialStatus | 1.3.6.1.4.1.164.8.5.2.1.18 | ||
| The status of the Hdlc link. | |||
| OBJECT-TYPE | |||
| INTEGER | busy(1), overflow(2), noStatus(255) | ||
| pktSwchHdlcCtsStatus | 1.3.6.1.4.1.164.8.5.2.1.19 | ||
| The CTS status. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| pktSwchHdlcRunningX25Lcn | 1.3.6.1.4.1.164.8.5.2.1.20 | ||
| The format of the string is ifIndex:LCN | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchHdlcRunningDlci | 1.3.6.1.4.1.164.8.5.2.1.21 | ||
| The format of the string is ifIndex:DLCI | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchHdlcMaxBuffToNet | 1.3.6.1.4.1.164.8.5.2.1.22 | ||
| The maximum number of buffers above which Flow Control is enabled | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchHdlcBuffToNet | 1.3.6.1.4.1.164.8.5.2.1.23 | ||
| The number of buffers waiting for transmission. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchStmTable | 1.3.6.1.4.1.164.8.7 | ||
| The STM table contains information for STM links | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchStmEntry | |||
| pktSwchStmEntry | 1.3.6.1.4.1.164.8.7.1 | ||
| Defines the contents of each line in the RAD STM Table. | |||
| OBJECT-TYPE | |||
| PktSwchStmEntry | |||
| pktSwchStmLinkNumber | 1.3.6.1.4.1.164.8.7.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link whose pktSwchPhyInterfaceProtocol is STM 4, 8, 16, or 24. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchStmInternalClockS | 1.3.6.1.4.1.164.8.7.1.2 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchStmInternalClockA | 1.3.6.1.4.1.164.8.7.1.3 | ||
| The current baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchStmConn | 1.3.6.1.4.1.164.8.7.1.4 | ||
| The connectivity status of the STM interface. | |||
| OBJECT-TYPE | |||
| INTEGER | disconnect(1), connect(2) | ||
| pktSwchStmSyncLoss | 1.3.6.1.4.1.164.8.7.1.5 | ||
| The counter for sync loss. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFr | 1.3.6.1.4.1.164.8.8 | ||
| OBJECT IDENTIFIER | |||
| pktSwchFrTotFunnels | 1.3.6.1.4.1.164.8.8.1 | ||
| The total number of Funnels on the PS. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrSTable | 1.3.6.1.4.1.164.8.8.2 | ||
| The Frame Relay Scratch Table includes the scratch values of configurable objects provided by the PS that are not included in RFC 1315. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrSEntry | |||
| pktSwchFrSEntry | 1.3.6.1.4.1.164.8.8.2.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Scratch Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrSEntry | |||
| pktSwchFrIfIndexS | 1.3.6.1.4.1.164.8.8.2.1.1 | ||
| This is the ifIndex of the frame relay port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrMaintProtS | 1.3.6.1.4.1.164.8.8.2.1.2 | ||
| This defines what maintenance protocol is running over this port. 0 - No maintenance protocol. 1 - ANSI PVC maintenance protocol running on DLCI number 0. 2 - LMI maintenance protocol running on DLCI number 1023. 4 - ITU Q.933 ANNEX A maintenance protocol running on DLCI number 0. 8 - Consolidate Link Layer Management CLLM running on DLCI number 1023. 8 cannot be a choice by itself, it can only be as part of the combination 9, 10, 12. XXX - The combination of 9, 10, 12. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..12 | ||
| pktSwchFrMaintModeS | 1.3.6.1.4.1.164.8.8.2.1.3 | ||
| This defines the mode of maintenance protocol running over this port. | |||
| OBJECT-TYPE | |||
| INTEGER | user(1), network(2), both(3) | ||
| pktSwchFrRxPoolRedLineS | 1.3.6.1.4.1.164.8.8.2.1.4 | ||
| When the number of empty receive buffers at the port reaches this figure (of frames),the port receiver is congested. This field value should be less than the Rx pool OK field. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..39 | ||
| pktSwchFrRxPoolOkS | 1.3.6.1.4.1.164.8.8.2.1.5 | ||
| Clear the receive congestion condition when the number of empty receive buffers at the port reaches this figure. This value (of frames) should be greater than the Rx pool red line. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..40 | ||
| pktSwchFrTxPoolRedLineS | 1.3.6.1.4.1.164.8.8.2.1.6 | ||
| When the number of frames awaiting transmission reaches this figure, the port transmitter is congested. This field value should be greater than the Tx pool OK field. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..500 | ||
| pktSwchFrTxPoolOkS | 1.3.6.1.4.1.164.8.8.2.1.7 | ||
| Clear the transmit congestion condition when the number of frames awaiting transmission at the port reaches this figure. This value (of frames) should be less than the Tx pool red line. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..499 | ||
| pktSwchFrTxCeilingS | 1.3.6.1.4.1.164.8.8.2.1.8 | ||
| The maximum allowable transmit pool for this port. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..500 | ||
| pktSwchFrInternalClockS | 1.3.6.1.4.1.164.8.8.2.1.9 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchFrNrzModeS | 1.3.6.1.4.1.164.8.8.2.1.10 | ||
| The data encoding format. | |||
| OBJECT-TYPE | |||
| INTEGER | nrz(1), nrzi(2) | ||
| pktSwchFrDlciHeaderModeS | 1.3.6.1.4.1.164.8.8.2.1.11 | ||
| Dlci Header length for this FR port. Option 4 means that there will be no management Dlci in the range of 1024 to 8388607. The management Dlci will be in the range of 0-15 or 991-1023. Default value: 1. | |||
| OBJECT-TYPE | |||
| INTEGER | two-octets(1), three-octets(2), four-octets(3), four-octets-nomanag(4) | ||
| pktSwchFrDcdLinkFailureS | 1.3.6.1.4.1.164.8.8.2.1.12 | ||
| Link Failure Detection by DCD. If Link Failure detection by DCD is on - (3), when the DCD is down, the FR SW will detect it and change the FR link status from UP to DOWN. A trap of LINK DOWN will be sent to the NMS. Default: (2). | |||
| OBJECT-TYPE | |||
| INTEGER | no-Detect(2), linkFailure-Detect(3) | ||
| pktSwchFrTxIdlesS | 1.3.6.1.4.1.164.8.8.2.1.13 | ||
| This parameter shows whether the PS will Transmit Idles between frames and control the RTS pin. Default: no(2). | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| pktSwchFrOperationModeS | 1.3.6.1.4.1.164.8.8.2.1.14 | ||
| When H/W Control is configured, the SCC H/W will detect the change in the DCD or CTS signals and Start or Stop transmission automatically. When S/W Control is configured the S/W will decide when to start or stop the transmission. Default: swControl(2). | |||
| OBJECT-TYPE | |||
| INTEGER | swControl(2), hwControl(3) | ||
| pktSwchFrPhysInterfOptionsS | 1.3.6.1.4.1.164.8.8.2.1.15 | ||
| This is the physical interface. Note that the DDS physical interface H/W does not exist in the FPS-8. It is relevant for other PS devices only. For FPS-8 only the default (noOption) should be used. Default: (2). | |||
| OBJECT-TYPE | |||
| INTEGER | noOption(2), dds4800bps(3), dds9600bps(4), dds19200bps(5), dds56000bos(6) | ||
| pktSwchFrATable | 1.3.6.1.4.1.164.8.8.3 | ||
| The Frame Relay Active Table includes statistics and the active values of configurable objects provided by the PS that are not included in RFC 1315. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrAEntry | |||
| pktSwchFrAEntry | 1.3.6.1.4.1.164.8.8.3.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Active Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrAEntry | |||
| pktSwchFrIfIndexA | 1.3.6.1.4.1.164.8.8.3.1.1 | ||
| This is the ifIndex of the frame relay port. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrMaintProtA | 1.3.6.1.4.1.164.8.8.3.1.2 | ||
| This defines what maintenance protocol is running over this port. 0 - No maintenance protocol. 1 - ANSI PVC maintenance protocol running on DLCI number 0. 2 - LMI maintenance protocol running on DLCI number 1023. 4 - ITU Q.933 ANNEX A maintenance protocol running on DLCI number 0. 8 - Consolidate Link Layer Management CLLM running on DLCI number 1023. 8 cannot be a choice by itself, it can only be as part of the combination 9, 10, 12. XXX - The combination of 9, 10, 12. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..12 | ||
| pktSwchFrMaintModeA | 1.3.6.1.4.1.164.8.8.3.1.3 | ||
| This defines the mode of maintenance protocol running over this port. | |||
| OBJECT-TYPE | |||
| INTEGER | user(1), network(2), both(3) | ||
| pktSwchFrRxPoolRedLineA | 1.3.6.1.4.1.164.8.8.3.1.4 | ||
| When the number of empty receive buffers at the port reaches this figure (of frames), the port receiver is congested. This field value should be less than the Rx pool OK field. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..39 | ||
| pktSwchFrRxPoolOkA | 1.3.6.1.4.1.164.8.8.3.1.5 | ||
| Clear the receive congestion condition when the number of empty receive buffers at the port reaches this figure. This value (of frames) should be greater than the Rx pool red line. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..40 | ||
| pktSwchFrTxPoolRedLineA | 1.3.6.1.4.1.164.8.8.3.1.6 | ||
| When the number of frames awaiting transmission reaches this figure, the port transmitter is congested. This field value should be greater than the Tx pool OK field. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..500 | ||
| pktSwchFrTxPoolOkA | 1.3.6.1.4.1.164.8.8.3.1.7 | ||
| Clear the transmit congestion condition when the number of frames awaiting transmission at the port reaches this figure. This value (of frames) should be less than the Tx pool red line. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..499 | ||
| pktSwchFrTxCeilingA | 1.3.6.1.4.1.164.8.8.3.1.8 | ||
| The maximum allowable transmit pool for this port. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..500 | ||
| pktSwchFrInternalClockA | 1.3.6.1.4.1.164.8.8.3.1.9 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchFrNrzModeA | 1.3.6.1.4.1.164.8.8.3.1.10 | ||
| The data encoding format. | |||
| OBJECT-TYPE | |||
| INTEGER | nrz(1), nrzi(2) | ||
| pktSwchFrDlcmiPollingInterval | 1.3.6.1.4.1.164.8.8.3.1.11 | ||
| This is the number of seconds between succes- sive status enquiry messages. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..30 | ||
| pktSwchFrDlcmiFullEnquiryInterval | 1.3.6.1.4.1.164.8.8.3.1.12 | ||
| Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pktSwchFrDlcmiErrorThreshold | 1.3.6.1.4.1.164.8.8.3.1.13 | ||
| This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| pktSwchFrDlcmiMonitoredEvents | 1.3.6.1.4.1.164.8.8.3.1.14 | ||
| This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| pktSwchFrDlciHeaderModeA | 1.3.6.1.4.1.164.8.8.3.1.15 | ||
| Dlci Header length for this FR port. Option 4 means that there will be no management Dlci in the range of 1024 to 8388607. The management Dlci will be in the range of 0-15 or 991-1023. Default value: 1. | |||
| OBJECT-TYPE | |||
| INTEGER | two-octets(1), three-octets(2), four-octets(3), four-octets-nomanag(4) | ||
| pktSwchFrDcdLinkFailureA | 1.3.6.1.4.1.164.8.8.3.1.16 | ||
| Link Failure Detection by DCD. If Link Failure detection by DCD is on - (3), when the DCD is down, the FR SW will detect it and change the FR link status from UP to DOWN. A trap of LINK DOWN will be sent to the NMS. Default: (2). | |||
| OBJECT-TYPE | |||
| INTEGER | no-Detect(2), linkFailure-Detect(3) | ||
| pktSwchFrTxIdlesA | 1.3.6.1.4.1.164.8.8.3.1.17 | ||
| This parameter shows whether the PS will Transmit Idles between frames and control the RTS pin. Default: no(2). | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| pktSwchFrOperationModeA | 1.3.6.1.4.1.164.8.8.3.1.18 | ||
| When H/W Control is configured, the SCC H/W will detect the change in the DCD or CTS signals and Start or Stop transmission automatically. When S/W Control is configured the S/W will decide when to start or stop the transmission. Default: swControl(2). | |||
| OBJECT-TYPE | |||
| INTEGER | swControl(2), hwControl(3) | ||
| pktSwchFrPhysInterfOptionsA | 1.3.6.1.4.1.164.8.8.3.1.19 | ||
| This is the physical interface. Note that the DDS physical interface H/W does not exist in the FPS-8. It is relevant for other PS devices only. For FPS-8 only the default (noOption) should be used. Default: (2). | |||
| OBJECT-TYPE | |||
| INTEGER | noOption(2), dds4800bps(3), dds9600bps(4), dds19200bps(5), dds56000bos(6) | ||
| pktSwchFrIfTable | 1.3.6.1.4.1.164.8.8.4 | ||
| The Frame Relay Active Port Table includes statistics and configurable objects provided by the PS that are not included in RFC 1315. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrIfEntry | |||
| pktSwchFrIfEntry | 1.3.6.1.4.1.164.8.8.4.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Port Active Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrIfEntry | |||
| pktSwchFrIfTxBytes | 1.3.6.1.4.1.164.8.8.4.1.1 | ||
| The number of Tx bytes. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfRxBytes | 1.3.6.1.4.1.164.8.8.4.1.2 | ||
| The number of Rx bytes. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfTxCongDiscards | 1.3.6.1.4.1.164.8.8.4.1.3 | ||
| The number of frames discarded because of Tx congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfDeTxFrames | 1.3.6.1.4.1.164.8.8.4.1.4 | ||
| The number of DE Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfDeRxFrames | 1.3.6.1.4.1.164.8.8.4.1.5 | ||
| The number of DE Rx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfFecnTxFrames | 1.3.6.1.4.1.164.8.8.4.1.6 | ||
| The number of FECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfFecnRxFrames | 1.3.6.1.4.1.164.8.8.4.1.7 | ||
| The number of FECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfBecnTxFrames | 1.3.6.1.4.1.164.8.8.4.1.8 | ||
| The number of BECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfBecnRxFrames | 1.3.6.1.4.1.164.8.8.4.1.9 | ||
| The number of BECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfCommRateViolTxFrames | 1.3.6.1.4.1.164.8.8.4.1.10 | ||
| The number of Tx committed rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfCommRateViolRxFrames | 1.3.6.1.4.1.164.8.8.4.1.11 | ||
| The number of Rx committed rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfExcessRateViolTxFrames | 1.3.6.1.4.1.164.8.8.4.1.12 | ||
| The number of Tx excess rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfExcessRateViolRxFrames | 1.3.6.1.4.1.164.8.8.4.1.13 | ||
| The number of Rx excess rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfBuffersInTxPool | 1.3.6.1.4.1.164.8.8.4.1.14 | ||
| The number of buffers waiting for transmission. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrIfFreeBuffersInRxPool | 1.3.6.1.4.1.164.8.8.4.1.15 | ||
| The number of free buffers in the Rx pool. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrIfLmiTxFrames | 1.3.6.1.4.1.164.8.8.4.1.16 | ||
| The number of LMI Tx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfLmiRxFrames | 1.3.6.1.4.1.164.8.8.4.1.17 | ||
| The number of LMI Rx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfAnsiTxFrames | 1.3.6.1.4.1.164.8.8.4.1.18 | ||
| The number of ANSI Tx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfAnsiRxFrames | 1.3.6.1.4.1.164.8.8.4.1.19 | ||
| The number of ANSI Rx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfCllmTxFrames | 1.3.6.1.4.1.164.8.8.4.1.20 | ||
| The number of CLLM Tx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfCllmRxFrames | 1.3.6.1.4.1.164.8.8.4.1.21 | ||
| The number of CLLM Rx Frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfTxCongestions | 1.3.6.1.4.1.164.8.8.4.1.22 | ||
| The number of Tx congestions. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfRxCongestions | 1.3.6.1.4.1.164.8.8.4.1.23 | ||
| The number of Rx congestions. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrIfTotDlciNumber | 1.3.6.1.4.1.164.8.8.4.1.24 | ||
| The total number of DLCIs defined. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrCircuitSTable | 1.3.6.1.4.1.164.8.8.5 | ||
| The Frame Relay Scratch Circuit Table includes configurable objects provided by the PS that are not included in RFC 1315. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrCircuitSEntry | |||
| pktSwchFrCircuitSEntry | 1.3.6.1.4.1.164.8.8.5.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Circuit Scratch Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrCircuitSEntry | |||
| pktSwchFrCircuitIfIndexS | 1.3.6.1.4.1.164.8.8.5.1.1 | ||
| This is the ifIndex of the circuit, according to RFC 1573. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrCircuitIndexS | 1.3.6.1.4.1.164.8.8.5.1.2 | ||
| This Index is the DLCI of the circuit. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrCircuitDestProtS | 1.3.6.1.4.1.164.8.8.5.1.3 | ||
| The protocol encapsulation, if any, on this DLCI. The MPE protocol is a proprietary RAD protocol that enables a generic HDLC device to have multiple connections over X.25 or Frame Relay. | |||
| OBJECT-TYPE | |||
| INTEGER | x25(1), none(2), hdlc(3), async(4), multiPoint(5), rfc1490(6) | ||
| pktSwchFrCircuitDestIdS | 1.3.6.1.4.1.164.8.8.5.1.4 | ||
| If the DLCI destination protocol is none or async, this field has a value of an existing DLCI or async channel, respectively. Otherwise, a value of zero is used. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchFrCircuitBackIdS | 1.3.6.1.4.1.164.8.8.5.1.5 | ||
| The backup DLCI which is used when the current DLCI goes inactive. The destination protocol and destination id are the same as in the current DLCI | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchFrCircuitTxCirIntervalS | 1.3.6.1.4.1.164.8.8.5.1.6 | ||
| The Tx CIR interval in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrCircuitTxCommittedS | 1.3.6.1.4.1.164.8.8.5.1.7 | ||
| The Tx committed rate in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitTxExcessS | 1.3.6.1.4.1.164.8.8.5.1.8 | ||
| The Tx excess in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitRxCirIntervalS | 1.3.6.1.4.1.164.8.8.5.1.9 | ||
| The Rx CIR interval in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrCircuitRxCommittedS | 1.3.6.1.4.1.164.8.8.5.1.10 | ||
| The Rx committed rate in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitRxExcessS | 1.3.6.1.4.1.164.8.8.5.1.11 | ||
| The Rx excess in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitFunnelIdS | 1.3.6.1.4.1.164.8.8.5.1.12 | ||
| The funnel ID. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchFrCircuitStatusS | 1.3.6.1.4.1.164.8.8.5.1.13 | ||
| The status of the circuit row in the Table. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchFrCircuitExtendedDlciS | 1.3.6.1.4.1.164.8.8.5.1.14 | ||
| The no. of the DLCI represented in 23 bits. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8388607 | ||
| pktSwchFrCircuitTxPriorityS | 1.3.6.1.4.1.164.8.8.5.1.15 | ||
| DLCI TX Priority level. The levels are defined in the pktSwchTxPriorityTable | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| pktSwchFrCircuitIsdnRoutIdS | 1.3.6.1.4.1.164.8.8.5.1.16 | ||
| ISDN destination. ID in the ISDN routing table containing the outgoing ISDN address for this DLCI. Default value: 0 for no ISDN routing ID. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchFrCircuitATable | 1.3.6.1.4.1.164.8.8.6 | ||
| The Frame Relay Active Circuit Table includes statistics and configurable objects provided by the PS that are not included in RFC 1315. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrCircuitAEntry | |||
| pktSwchFrCircuitAEntry | 1.3.6.1.4.1.164.8.8.6.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Circuit Active Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrCircuitAEntry | |||
| pktSwchFrCircuitIfIndexA | 1.3.6.1.4.1.164.8.8.6.1.1 | ||
| This is the ifIndex of the circuit, according to RFC 1573. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrCircuitIndexA | 1.3.6.1.4.1.164.8.8.6.1.2 | ||
| This Index is the DLCI of the circuit. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrCircuitDestProtA | 1.3.6.1.4.1.164.8.8.6.1.3 | ||
| The protocol encapsulation, if any, on this DLCI. The MPE protocol is a proprietary RAD protocol that enables a generic HDLC device to have multiple connections over X.25 or Frame Relay. | |||
| OBJECT-TYPE | |||
| INTEGER | x25(1), none(2), hdlc(3), async(4), multiPoint(5), rfc1490(6) | ||
| pktSwchFrCircuitDestIdA | 1.3.6.1.4.1.164.8.8.6.1.4 | ||
| If the DLCI destination protocol is none or async, this field has a value of an existing DLCI or async channel, respectively. Otherwise, a value of zero is used. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchFrCircuitBackIdA | 1.3.6.1.4.1.164.8.8.6.1.5 | ||
| The backup DLCI which is used when the current DLCI goes inactive. The destination protocol and destination id are the same as in the current DLCI | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchFrCircuitTxCirIntervalA | 1.3.6.1.4.1.164.8.8.6.1.6 | ||
| The Tx CIR interval in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrCircuitTxCommittedA | 1.3.6.1.4.1.164.8.8.6.1.7 | ||
| The Tx committed rate in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitTxExcessA | 1.3.6.1.4.1.164.8.8.6.1.8 | ||
| The Tx excess in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitRxCirIntervalA | 1.3.6.1.4.1.164.8.8.6.1.9 | ||
| The Rx CIR interval in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrCircuitRxCommittedA | 1.3.6.1.4.1.164.8.8.6.1.10 | ||
| The Rx committed rate in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitRxExcessA | 1.3.6.1.4.1.164.8.8.6.1.11 | ||
| The Rx excess in bytes per interval. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrCircuitFunnelIdA | 1.3.6.1.4.1.164.8.8.6.1.12 | ||
| The funnel ID. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchFrCircuitFunnelStat | 1.3.6.1.4.1.164.8.8.6.1.13 | ||
| The funnel status. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchFrCircuitTxCongDiscards | 1.3.6.1.4.1.164.8.8.6.1.14 | ||
| The number of frames discarded because of Tx congestion. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitDeTxFrames | 1.3.6.1.4.1.164.8.8.6.1.15 | ||
| The number of DE Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitDeRxFrames | 1.3.6.1.4.1.164.8.8.6.1.16 | ||
| The number of DE Rx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitFecnTxFrames | 1.3.6.1.4.1.164.8.8.6.1.17 | ||
| The number of FECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitBecnTxFrames | 1.3.6.1.4.1.164.8.8.6.1.18 | ||
| The number of BECN Tx frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitCommRateViolTxFrames | 1.3.6.1.4.1.164.8.8.6.1.19 | ||
| The number of Tx committed rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitCommRateViolRxFrames | 1.3.6.1.4.1.164.8.8.6.1.20 | ||
| The number of Rx committed rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitExcessRateViolTxFrames | 1.3.6.1.4.1.164.8.8.6.1.21 | ||
| The number of Tx excess rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitExcessRateViolRxFrames | 1.3.6.1.4.1.164.8.8.6.1.22 | ||
| The number of Rx excess rate violations in number of frames. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchFrCircuitState | 1.3.6.1.4.1.164.8.8.6.1.23 | ||
| Indicates whether the particular virtual cir- cuit is new or not. | |||
| OBJECT-TYPE | |||
| INTEGER | new(1), noState(2) | ||
| pktSwchFrCircuitExtendedDlciA | 1.3.6.1.4.1.164.8.8.6.1.24 | ||
| The no. of the DLCI represented in 23 bits. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8388607 | ||
| pktSwchFrCircuitTxPriorityA | 1.3.6.1.4.1.164.8.8.6.1.25 | ||
| DLCI TX Priority level. The levels are defined in the pktSwchTxPriorityTable | |||
| OBJECT-TYPE | |||
| Integer32 | 1..4 | ||
| pktSwchFrCircuitIsdnRoutIdA | 1.3.6.1.4.1.164.8.8.6.1.26 | ||
| ISDN destination. ID in the ISDN routing table containing the outgoing ISDN address for this DLCI. Default value: 0 for no ISDN routing ID. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchFrFunnelSTable | 1.3.6.1.4.1.164.8.8.7 | ||
| The Frame Relay Funnel Table defines the funnels that DLCIs may use. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrFunnelSEntry | |||
| pktSwchFrFunnelSEntry | 1.3.6.1.4.1.164.8.8.7.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Funnel Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrFunnelSEntry | |||
| pktSwchFrFunnelIndexS | 1.3.6.1.4.1.164.8.8.7.1.1 | ||
| This is the index of the funnel table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrFunnelSizeS | 1.3.6.1.4.1.164.8.8.7.1.2 | ||
| The number of frames the funnel can store internally, where each frame is 512 bytes. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..256 | ||
| pktSwchFrFunnelHighWaterFramesS | 1.3.6.1.4.1.164.8.8.7.1.3 | ||
| The maximum number of frames the funnel can hold before it expands and transmits all the data. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..256 | ||
| pktSwchFrFunnelHighWaterBytesS | 1.3.6.1.4.1.164.8.8.7.1.4 | ||
| The maximum number of bytes the funnel can hold before it expands and transmits all the data. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrFunnelGaugeTxRateS | 1.3.6.1.4.1.164.8.8.7.1.5 | ||
| The outgoing data rate in bytes per window of the funnel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrFunnelTransWindowS | 1.3.6.1.4.1.164.8.8.7.1.6 | ||
| The transmission rate is measured during a sliding time window. This parameter defines the window in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrFunnelStatusS | 1.3.6.1.4.1.164.8.8.7.1.7 | ||
| The status of this funnel table entry. The choices are those defined in the SNMPv2 Textual Conventions for RowStatus. This will allow easy replacement of the INTEGER syntax with the RowStatus textual convention SYNTAX. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchFrFunnelATable | 1.3.6.1.4.1.164.8.8.8 | ||
| The Frame Relay Funnel Table defines the funnels that DLCIs may use. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrFunnelAEntry | |||
| pktSwchFrFunnelAEntry | 1.3.6.1.4.1.164.8.8.8.1 | ||
| Defines the contents of each line in the RAD PS Frame Relay Funnel Table. | |||
| OBJECT-TYPE | |||
| PktSwchFrFunnelAEntry | |||
| pktSwchFrFunnelIndexA | 1.3.6.1.4.1.164.8.8.8.1.1 | ||
| This is the index of the funnel table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrFunnelSizeA | 1.3.6.1.4.1.164.8.8.8.1.2 | ||
| The number of frames the funnel can store internally, where each frame is 512 bytes. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..256 | ||
| pktSwchFrFunnelHighWaterFramesA | 1.3.6.1.4.1.164.8.8.8.1.3 | ||
| The maximum number of frames the funnel can hold before it expands and transmits all the data. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..256 | ||
| pktSwchFrFunnelHighWaterBytesA | 1.3.6.1.4.1.164.8.8.8.1.4 | ||
| The maximum number of bytes the funnel can hold before it expands and transmits all the data. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrFunnelGaugeTxRateA | 1.3.6.1.4.1.164.8.8.8.1.5 | ||
| The outgoing data rate in bytes per window of the funnel. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchFrFunnelTransWindowA | 1.3.6.1.4.1.164.8.8.8.1.6 | ||
| The transmission rate is measured during a sliding time window. This parameter defines the window in 1/10 seconds. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..10 | ||
| pktSwchFrDlciMapTable | 1.3.6.1.4.1.164.8.8.9 | ||
| The Frame Relay Dlci mapping Table maps the Dlci numbers. For each long Dlci a short one is mapped. A long Dlci is a Dlci which contains a Dlci header of 3 or 4 bytes instead of the regular 2 bytes. The long Dlci number has values from 1024 to 8,388,607. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchFrDlciMapEntry | |||
| pktSwchFrDlciMapEntry | 1.3.6.1.4.1.164.8.8.9.1 | ||
| Defines the contents of each Dlci Map Table entry. | |||
| OBJECT-TYPE | |||
| PktSwchFrDlciMapEntry | |||
| pktSwchFrDlciMapPort | 1.3.6.1.4.1.164.8.8.9.1.1 | ||
| Frame Relay port no. : 1-8 for FPS-8, 1-4 for FPS-4, 1-3 for APS, 1-6 for SPS-6, 1-12 for SPS-12. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchFrDlciMapLongDlci | 1.3.6.1.4.1.164.8.8.9.1.2 | ||
| The Long Dlci number. For Dlci's of 4 octets, the long Dlci number has values from 1024 to 8,388,607. For Dlci's of 2 octets, the long Dlci number has values of 16-991. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8388607 | ||
| pktSwchFrDlciMapShortDlci | 1.3.6.1.4.1.164.8.8.9.1.3 | ||
| The Short Dlci number. Legal values: 0 - 1023. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..1023 | ||
| pktSwchFrDlciMapStatus | 1.3.6.1.4.1.164.8.8.9.1.4 | ||
| The status of the map row in the Table. The only value which can be set is: createRequest. This value is set when a new long dlci is created. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchMpe | 1.3.6.1.4.1.164.8.9 | ||
| OBJECT IDENTIFIER | |||
| pktSwchMpeSTable | 1.3.6.1.4.1.164.8.9.1 | ||
| The MPE Table defines Scratch configuration parameters for the MPE protocol. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchMpeSEntry | |||
| pktSwchMpeSEntry | 1.3.6.1.4.1.164.8.9.1.1 | ||
| Defines the contents of each line in the MPE Table. | |||
| OBJECT-TYPE | |||
| PktSwchMpeSEntry | |||
| pktSwchMpeLinkNumberS | 1.3.6.1.4.1.164.8.9.1.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is MPE. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchMpeInactivityS | 1.3.6.1.4.1.164.8.9.1.1.2 | ||
| The amount of time in minutes of inactivity that will cause the session to disconnect. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchMpeX25FacilitiesS | 1.3.6.1.4.1.164.8.9.1.1.3 | ||
| This specifies the X.25 facilities. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Packet size negotiation 2 Window size negotiation 4 Reverse charge. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchMpeLocSubAddr1S | 1.3.6.1.4.1.164.8.9.1.1.4 | ||
| The first local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| pktSwchMpeLocSubAddr2S | 1.3.6.1.4.1.164.8.9.1.1.5 | ||
| The second local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| pktSwchMpeFlwCtrlDurS | 1.3.6.1.4.1.164.8.9.1.1.6 | ||
| The duration in 50 milliseconds of a hardware flow control signal. Default is 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeFlwCtrlOptS | 1.3.6.1.4.1.164.8.9.1.1.7 | ||
| This specifies the type of flow control of the MPE link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No flow control 1 CTS flow control 2 Clock flow control. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..3 | ||
| pktSwchMpeFlwCtrlBufS | 1.3.6.1.4.1.164.8.9.1.1.8 | ||
| The number of buffers that will be allocated for the MPE link. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeInternalClkS | 1.3.6.1.4.1.164.8.9.1.1.9 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchMpeATable | 1.3.6.1.4.1.164.8.9.2 | ||
| The MPE Table defines Active configuration parameters for the MPE protocol. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchMpeAEntry | |||
| pktSwchMpeAEntry | 1.3.6.1.4.1.164.8.9.2.1 | ||
| Defines the contents of each line in the MPE Table. | |||
| OBJECT-TYPE | |||
| PktSwchMpeAEntry | |||
| pktSwchMpeLinkNumberA | 1.3.6.1.4.1.164.8.9.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceNumber. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is MPE. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchMpeInactivityA | 1.3.6.1.4.1.164.8.9.2.1.2 | ||
| The amount of time in minutes of inactivity that will cause the session to disconnect. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchMpeX25FacilitiesA | 1.3.6.1.4.1.164.8.9.2.1.3 | ||
| This specifies the X.25 facilities. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No options 1 Packet size negotiation 2 Window size negotiation 4 Reverse charge. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..7 | ||
| pktSwchMpeLocSubAddr1A | 1.3.6.1.4.1.164.8.9.2.1.4 | ||
| The first local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| pktSwchMpeLocSubAddr2A | 1.3.6.1.4.1.164.8.9.2.1.5 | ||
| The second local subaddress. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99 | ||
| pktSwchMpeFlwCtrlDurA | 1.3.6.1.4.1.164.8.9.2.1.6 | ||
| The duration in 50 milliseconds of a hardware flow control signal. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeFlwCtrlOptA | 1.3.6.1.4.1.164.8.9.2.1.7 | ||
| This specifies the type of flow control of the MPE link. The value is a sum of values (powers of two), where each value in the sum represents an option. The values that may be included in the sum and their meanings are: 0 No flow control 1 CTS flow control 2 Clock flow control. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..3 | ||
| pktSwchMpeFlwCtrlBufA | 1.3.6.1.4.1.164.8.9.2.1.8 | ||
| The number of buffers that will be allocated for the MPE link. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeInternalClkA | 1.3.6.1.4.1.164.8.9.2.1.9 | ||
| The baud rate of the internal clock. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r504Kbps(13), r768Kbps(14), r1008Kbps(15), r1466Kbps(16), r2016Kbps(17), external(255) | ||
| pktSwchMpeCtsStatus | 1.3.6.1.4.1.164.8.9.2.1.10 | ||
| The CTS status. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| pktSwchMpeAidSTable | 1.3.6.1.4.1.164.8.9.3 | ||
| The AID Table defines Scratch configuration parameters for the logical connections (Address Id). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchMpeAidSEntry | |||
| pktSwchMpeAidSEntry | 1.3.6.1.4.1.164.8.9.3.1 | ||
| Defines the contents of each line in the MPE Table. | |||
| OBJECT-TYPE | |||
| PktSwchMpeAidSEntry | |||
| pktSwchMpeAddressIdS | 1.3.6.1.4.1.164.8.9.3.1.1 | ||
| The Address Id (AID) with which this entry is associated. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchMpeAidMainTypeS | 1.3.6.1.4.1.164.8.9.3.1.2 | ||
| The protocol with which the AID is communicating. | |||
| OBJECT-TYPE | |||
| INTEGER | x25Svc(1), x25Pvc(2), fr(3), innerCom(4), notActive(255) | ||
| pktSwchMpeAidMainIdS | 1.3.6.1.4.1.164.8.9.3.1.3 | ||
| The link number of the protocol with which the AID is communicating. The link number of the protocol with which the AID is communicating. For X.25 SVC this number is Any Autocall ID (Pre-defined) , values: 1..200 For X.25 PVC this number is a local PVC that its source link has already been set to the current link with a prefix of N. values: 1..200 For FR this number is any Frame Relay link number (Pre-defined), values: 1..12 For Inner communication this number is an HDLC or MPE link number (Pre-defined), values: 1..12 For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeAidMainSubIdS | 1.3.6.1.4.1.164.8.9.3.1.4 | ||
| The DLCI with which the AID is communicating. Sub ID is used only when Type is Frame Relay or Inner Comm. The DLCI or destination AID with which the current AID is communicating. If type is: Frame Relay PVC: Sub ID must be an existing DLCI, 16-991. (The DLCI's destination protocol has to be predefined to MPE). If type is: Inner Communication: In case of an HDLC link, Sub ID must be 0. In case of an MPE link, Sub ID must be in AID permitted range. For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..991 | ||
| pktSwchMpeAidBackupTypeS | 1.3.6.1.4.1.164.8.9.3.1.5 | ||
| The protocol with which the AID is communicating on the backup. | |||
| OBJECT-TYPE | |||
| INTEGER | x25Svc(1), x25Pvc(2), fr(3), innerCom(4), notActive(255) | ||
| pktSwchMpeAidBackupIdS | 1.3.6.1.4.1.164.8.9.3.1.6 | ||
| The link number of the protocol with which the AID is communicating on the backup. The link number of the protocol with which the AID is communicating. For X.25 SVC this number is Any Autocall ID (Pre-defined) , values: 1..200 For X.25 PVC this number is a local PVC that its source link has already been set to the current link with a prefix of N. values: 1..200 For FR this number is any Frame Relay link number (Pre-defined), values: 1..12 For Inner communication this number is an HDLC or MPE link number (Pre-defined), values: 1..12 For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeAidBackupSubIdS | 1.3.6.1.4.1.164.8.9.3.1.7 | ||
| The DLCI with which the AID is communicating. Sub ID is used only when Type is Frame Relay or Inner Comm. The DLCI or destination AID with which the current AID is communicating. If type is: Frame Relay PVC: Sub ID must be an existing DLCI, 16-991. (The DLCI's destination protocol has to be predefined to MPE). If type is: Inner Communication: In case of an HDLC link, Sub ID must be 0. In case of an MPE link, Sub ID must be in AID permitted range. For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..991 | ||
| pktSwchMpeAidStatusS | 1.3.6.1.4.1.164.8.9.3.1.8 | ||
| The status of this Address Id table entry. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchMpeAidATable | 1.3.6.1.4.1.164.8.9.4 | ||
| The AID Table defines Active configuration parameters for the logical connections (Address Id). | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchMpeAidAEntry | |||
| pktSwchMpeAidAEntry | 1.3.6.1.4.1.164.8.9.4.1 | ||
| Defines the contents of each line in the MPE Table. | |||
| OBJECT-TYPE | |||
| PktSwchMpeAidAEntry | |||
| pktSwchMpeAddressIdA | 1.3.6.1.4.1.164.8.9.4.1.1 | ||
| The Address Id (AID) with which this entry is associated. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchMpeAidMainTypeA | 1.3.6.1.4.1.164.8.9.4.1.2 | ||
| The protocol with which the AID is communicating. | |||
| OBJECT-TYPE | |||
| INTEGER | x25Svc(1), x25Pvc(2), fr(3), innerCom(4), notActive(255) | ||
| pktSwchMpeAidMainIdA | 1.3.6.1.4.1.164.8.9.4.1.3 | ||
| The link number of the protocol with which the AID is communicating. The link number of the protocol with which the AID is communicating. For X.25 SVC this number is Any Autocall ID (Pre-defined) , values: 1..200 For X.25 PVC this number is a local PVC that its source link has already been set to the current link with a prefix of N. values: 1..200 For FR this number is any Frame Relay link number (Pre-defined), values: 1..12 For Inner communication this number is an HDLC or MPE link number (Pre-defined), values: 1..12 For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeAidMainSubIdA | 1.3.6.1.4.1.164.8.9.4.1.4 | ||
| The DLCI with which the AID is communicating. Sub ID is used only when Type is Frame Relay or Inner Comm. The DLCI or destination AID with which the current AID is communicating. If type is: Frame Relay PVC: Sub ID must be an existing DLCI, 16-991. (The DLCI's destination protocol has to be predefined to MPE). If type is: Inner Communication: In case of an HDLC link, Sub ID must be 0. In case of an MPE link, Sub ID must be in AID permitted range. For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..991 | ||
| pktSwchMpeAidBackupTypeA | 1.3.6.1.4.1.164.8.9.4.1.5 | ||
| The protocol with which the AID is communicating on the backup. | |||
| OBJECT-TYPE | |||
| INTEGER | x25Svc(1), x25Pvc(2), fr(3), innerCom(4), notActive(255) | ||
| pktSwchMpeAidBackupIdA | 1.3.6.1.4.1.164.8.9.4.1.6 | ||
| The link number of the protocol with which the AID is communicating on the backup. The link number of the protocol with which the AID is communicating. For X.25 SVC this number is Any Autocall ID (Pre-defined) , values: 1..200 For X.25 PVC this number is a local PVC that its source link has already been set to the current link with a prefix of N. values: 1..200 For FR this number is any Frame Relay link number (Pre-defined), values: 1..12 For Inner communication this number is an HDLC or MPE link number (Pre-defined), values: 1..12 For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchMpeAidBackupSubIdA | 1.3.6.1.4.1.164.8.9.4.1.7 | ||
| The DLCI with which the AID is communicating. Sub ID is used only when Type is Frame Relay or Inner Comm. The DLCI or destination AID with which the current AID is communicating. If type is: Frame Relay PVC: Sub ID must be an existing DLCI, 16-991. (The DLCI's destination protocol has to be predefined to MPE). If type is: Inner Communication: In case of an HDLC link, Sub ID must be 0. In case of an MPE link, Sub ID must be in AID permitted range. For notActive this number is 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..991 | ||
| pktSwchMpeAidConn | 1.3.6.1.4.1.164.8.9.4.1.8 | ||
| The connectivity status of the AID. | |||
| OBJECT-TYPE | |||
| INTEGER | disconnect(1), connect(2), pvc(3) | ||
| pktSwchMpeAidFlwCtrl | 1.3.6.1.4.1.164.8.9.4.1.9 | ||
| The Flow Control status of the AID. | |||
| OBJECT-TYPE | |||
| INTEGER | inactive(1), active(2) | ||
| pktSwchSlip | 1.3.6.1.4.1.164.8.10 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSlipSTable | 1.3.6.1.4.1.164.8.10.1 | ||
| The Scratch Slip Table contains configuration information for Slip links | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSlipSEntry | |||
| pktSwchSlipSEntry | 1.3.6.1.4.1.164.8.10.1.1 | ||
| Defines the contents of each line in the RAD Slip Table. | |||
| OBJECT-TYPE | |||
| PktSwchSlipSEntry | |||
| pktSwchSlipLinkNumberS | 1.3.6.1.4.1.164.8.10.1.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceIfIndex. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is Slip. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSlipSpeedS | 1.3.6.1.4.1.164.8.10.1.1.2 | ||
| This parameter determines the rate of data transmission to and from the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21) | ||
| pktSwchSlipFCOptionS | 1.3.6.1.4.1.164.8.10.1.1.3 | ||
| The flow control options 0 - No HARDWARE flow control 1..254 - Timer value (in 50ms intervals), when timer expires, flow control stops 255 - The timer is not used | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSlipStopBitsS | 1.3.6.1.4.1.164.8.10.1.1.4 | ||
| This entry indicates the number of stop bits per character supported by the PAD. The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), oneAndHalf(3) | ||
| pktSwchSlipBitPerCharS | 1.3.6.1.4.1.164.8.10.1.1.5 | ||
| The number of data bits per character supported by the Slip link. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..8 | ||
| pktSwchSlipParityS | 1.3.6.1.4.1.164.8.10.1.1.6 | ||
| This entry selects the type of parity to be checked and or generated by the PAD when radSPSProfileParTreat is a value other than 255. The options are (1) space parity, (2) mark parity, (3) even parity, (4) odd parity, or (255) no parity. | |||
| OBJECT-TYPE | |||
| INTEGER | space(1), mark(2), even(3), odd(4), none(255) | ||
| pktSwchSlipIpAddressS | 1.3.6.1.4.1.164.8.10.1.1.7 | ||
| The IP address connected to this Slip port. This variable is used when an automatic connection is done by the IP Routing. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchSlipIpMaskS | 1.3.6.1.4.1.164.8.10.1.1.8 | ||
| The IP mask. This variable is used when an automatic connection by the IP Routing is done. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchSlipDefEncapsTypeS | 1.3.6.1.4.1.164.8.10.1.1.9 | ||
| Destination protocol of this Slip port. This variable is used when a direct connection without IP Routing is done. | |||
| OBJECT-TYPE | |||
| INTEGER | slip(1), x25SVC(2), x25PVC(3), frameRelay(4), hdlc(5), none(255) | ||
| pktSwchSlipDefDestinationS | 1.3.6.1.4.1.164.8.10.1.1.10 | ||
| Default destination for this Slip port. This variable is used when a direct connection without IP Routing is done. Possible values: Default : Not Used. X.25 PVC: Port:LCN or a pre defined PVC number X.25 SVC: X.25 Addr or cid followed by a predefined Call ID number Frame Relay: Port:DLCI HDLC: HDLC Port Number SLIP: SLIP Channel Number | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSlipATable | 1.3.6.1.4.1.164.8.10.2 | ||
| The Active Slip Table contains configuration information for Slip links | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSlipAEntry | |||
| pktSwchSlipAEntry | 1.3.6.1.4.1.164.8.10.2.1 | ||
| Defines the contents of each line in the RAD Slip Table. | |||
| OBJECT-TYPE | |||
| PktSwchSlipAEntry | |||
| pktSwchSlipLinkNumberA | 1.3.6.1.4.1.164.8.10.2.1.1 | ||
| The link number with which this entry is associated. This value corresponds to pktSwchPhyInterfaceIfIndex. There is an entry for each link for which the pktSwchPhyInterfaceProtocol is Slip. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSlipSpeedA | 1.3.6.1.4.1.164.8.10.2.1.2 | ||
| This parameter determines the rate of data transmission to and from the DTE. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21) | ||
| pktSwchSlipFCOptionA | 1.3.6.1.4.1.164.8.10.2.1.3 | ||
| The flow control options 0 - No HARDWARE flow control 1..254 - Timer value (in 50ms intervals), when timer expires, flow control stops 255 - The timer is not used | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchSlipStopBitsA | 1.3.6.1.4.1.164.8.10.2.1.4 | ||
| This entry indicates the number of stop bits per character supported by the PAD. The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), oneAndHalf(3) | ||
| pktSwchSlipBitPerCharA | 1.3.6.1.4.1.164.8.10.2.1.5 | ||
| The number of data bits per character supported by the Slip link. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..8 | ||
| pktSwchSlipParityA | 1.3.6.1.4.1.164.8.10.2.1.6 | ||
| This entry selects the type of parity to be checked and or generated by the PAD when radSPSProfileParTreat is a value other than 255. The options are (1) space parity, (2) mark parity, (3) even parity, (4) odd parity, or (255) no parity. | |||
| OBJECT-TYPE | |||
| INTEGER | space(1), mark(2), even(3), odd(4), none(255) | ||
| pktSwchSlipIpAddressA | 1.3.6.1.4.1.164.8.10.2.1.7 | ||
| The IP address connected to this Slip port. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchSlipIpMaskA | 1.3.6.1.4.1.164.8.10.2.1.8 | ||
| The IP mask. | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchSlipDefEncapsTypeA | 1.3.6.1.4.1.164.8.10.2.1.9 | ||
| Destination protocol of this Slip port. | |||
| OBJECT-TYPE | |||
| INTEGER | slip(1), x25SVC(2), x25PVC(3), frameRelay(4), hdlc(5), none(255) | ||
| pktSwchSlipDefDestinationA | 1.3.6.1.4.1.164.8.10.2.1.10 | ||
| Default destination for this Slip port. This variable is used when a direct connection without IP Routing is done. Possible values: Default : Not Used. X.25 PVC: Port:LCN or a pre defined PVC number X.25 SVC: X.25 Addr or cid followed by a predefined Call ID number Frame Relay: Port:DLCI HDLC: HDLC Port Number SLIP: SLIP Channel Number | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchSna | 1.3.6.1.4.1.164.8.11 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSnaSDLCLinkTableS | 1.3.6.1.4.1.164.8.11.1 | ||
| The SDLC Link Table defines the SDLC links configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaSDLCLinkEntryS | |||
| pktSwchSnaSDLCLinkEntryS | 1.3.6.1.4.1.164.8.11.1.1 | ||
| SDLC Link Entry defines the contents of each link in the SDLC Link Table. | |||
| OBJECT-TYPE | |||
| PktSwchSnaSDLCLinkEntryS | |||
| pktSwchSnaSDLCLinkTypeS | 1.3.6.1.4.1.164.8.11.1.1.1 | ||
| This parameter identifies whether this link operates as TPAD(Primary) or HPAD(Secondary) SDLC device. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaSDLCLinkPUSharedS | 1.3.6.1.4.1.164.8.11.1.1.2 | ||
| This parameter defines whether the link participates with more than one PU or not. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(1), no(2) | ||
| pktSwchSnaSDLCLinkDuplexPhyS | 1.3.6.1.4.1.164.8.11.1.1.3 | ||
| This parameter describes whether the physical level of the SDLC line is half or full duplex. | |||
| OBJECT-TYPE | |||
| INTEGER | half(1), full(2) | ||
| pktSwchSnaSDLCLinkflagsS | 1.3.6.1.4.1.164.8.11.1.1.4 | ||
| Number of flags between frames. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..15 | ||
| pktSwchSnaSDLCLinkDuplexS | 1.3.6.1.4.1.164.8.11.1.1.5 | ||
| This parameter shows wether the link level is Two Way Alternate or Two Way Simultaneous. | |||
| OBJECT-TYPE | |||
| INTEGER | twoWayAlter(1), twoWaySimul(2) | ||
| pktSwchSnaSDLCLinkClockS | 1.3.6.1.4.1.164.8.11.1.1.6 | ||
| This parameter defines the link clock rate | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600Bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48000bps(7), r56000bps(8), r64000bps(9), r128000bps(10), r256000bps(11), r384000bps(12), r504000bps(13), r768000bps(14), r1008000bps(15), r1466000bps(16), r2016000bps(17), external(255) | ||
| pktSwchSnaSDLCLinkNRZS | 1.3.6.1.4.1.164.8.11.1.1.7 | ||
| This parameter describes the following combinations of NRZ, NRZI with FLAGS or IDLE between frames: Legal values: 1 - NRZ with FLAGs between frames. RTS is Constant 2 - NRZI with FLAGs between frames. RTS is Constant. 3 - NRZ with IDLE between frames. RTS is Controlled. 4 - NRZI with IDLE between frames. RTS is Controlled. | |||
| OBJECT-TYPE | |||
| INTEGER | nrzFlags(1), nrziFlags(2), nrzIdle(3), nrziIdle(4) | ||
| pktSwchSnaSDLCLinkTableA | 1.3.6.1.4.1.164.8.11.2 | ||
| The SDLC Link Table defines the SDLC links configured on the SPS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaSDLCLinkEntryA | |||
| pktSwchSnaSDLCLinkEntryA | 1.3.6.1.4.1.164.8.11.2.1 | ||
| SDLC Link Entry defines the contents of each link in the SDLC Link Table. | |||
| OBJECT-TYPE | |||
| PktSwchSnaSDLCLinkEntryA | |||
| pktSwchSnaSDLCLinkTypeA | 1.3.6.1.4.1.164.8.11.2.1.1 | ||
| This parameter identifies whether this link operates as TPAD(Primary) or HPAD(Secondary) SDLC device. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaSDLCLinkPUSharedA | 1.3.6.1.4.1.164.8.11.2.1.2 | ||
| This parameter defines whether the link participates with more than one PU or not. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(1), no(2) | ||
| pktSwchSnaSDLCLinkDuplexPhyA | 1.3.6.1.4.1.164.8.11.2.1.3 | ||
| This parameter describes whether the physical level of the SDLC line is half or full duplex. | |||
| OBJECT-TYPE | |||
| INTEGER | half(1), full(2) | ||
| pktSwchSnaSDLCLinkflagsA | 1.3.6.1.4.1.164.8.11.2.1.4 | ||
| Number of flags between frames. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..15 | ||
| pktSwchSnaSDLCLinkDuplexA | 1.3.6.1.4.1.164.8.11.2.1.5 | ||
| This parameter shows wether the link level is Two Way Alternate or Two Way Simultaneous. | |||
| OBJECT-TYPE | |||
| INTEGER | twoWayAlter(1), twoWaySimul(2) | ||
| pktSwchSnaSDLCLinkClockA | 1.3.6.1.4.1.164.8.11.2.1.6 | ||
| This parameter defines the link clock rate. | |||
| OBJECT-TYPE | |||
| INTEGER | r2400bps(1), r4800bps(2), r9600Bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48000bps(7), r56000bps(8), r64000bps(9), r128000bps(10), r256000bps(11), r384000bps(12), r504000bps(13), r768000bps(14), r1008000bps(15), r1466000bps(16), r2016000bps(17), external(255) | ||
| pktSwchSnaSDLCLinkNRZA | 1.3.6.1.4.1.164.8.11.2.1.7 | ||
| This parameter describes the following combinations of NRZ, NRZI with FLAGS or IDLE between frames: Legal values: 1 - NRZ with FLAGs between frames. RTS is Constant 2 - NRZI with FLAGs between frames. RTS is Constant. 3 - NRZ with IDLE between frames. RTS is Controlled. 4 - NRZI with IDLE between frames. RTS is Controlled. | |||
| OBJECT-TYPE | |||
| INTEGER | nrzFlags(1), nrziFlags(2), nrzIdle(3), nrziIdle(4) | ||
| pktSwchSnaSDLCLinkStatFrames | 1.3.6.1.4.1.164.8.11.2.1.8 | ||
| The number of frames received or transmitted via this link | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaSDLCLinkStatErrors | 1.3.6.1.4.1.164.8.11.2.1.9 | ||
| The number of error frames received. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaSDLCLinkStatInvalidAddresses | 1.3.6.1.4.1.164.8.11.2.1.10 | ||
| The number of frames with wrong address received by this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaSDLCLinkStatShortFrames | 1.3.6.1.4.1.164.8.11.2.1.11 | ||
| The number of short frames received by this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUTableS | 1.3.6.1.4.1.164.8.11.3 | ||
| The SDLC PU table defines the PUs configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUEntryS | |||
| pktSwchSnaPUEntryS | 1.3.6.1.4.1.164.8.11.3.1 | ||
| SDLC PU Entry defines the contents of each PU in the SDLC PU Table. | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUEntryS | |||
| pktSwchSnaPUNumberS | 1.3.6.1.4.1.164.8.11.3.1.1 | ||
| This parameter defines an identifier associated with the PU Entry which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUXIDProcessingS | 1.3.6.1.4.1.164.8.11.3.1.2 | ||
| Exchange Identification (XID) processing. The following values are legal: 1 - Local XID handling 2 - End-to-End XID handling, Support for NON-Activation XID 3 - End-to-End XID handling, NO Support for NON-Activation XID | |||
| OBJECT-TYPE | |||
| INTEGER | localXid(1), end2EndSupNoAct(2), end2EndNoSupNoAct(3) | ||
| pktSwchSnaPUEnableS | 1.3.6.1.4.1.164.8.11.3.1.3 | ||
| The PU runs or not at this specific time | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| pktSwchSnaPULinkATypeS | 1.3.6.1.4.1.164.8.11.3.1.4 | ||
| The PU link A type. | |||
| OBJECT-TYPE | |||
| INTEGER | sdlc(1), x25Qllc(2), frameRelayLLC2(3) | ||
| pktSwchSnaPULinkARoleS | 1.3.6.1.4.1.164.8.11.3.1.5 | ||
| The PU role for link A. Note that the role of an SDLC PU may not be changed. It is defined by the SDLC Link Type. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaPULinkBTypeS | 1.3.6.1.4.1.164.8.11.3.1.6 | ||
| The PU partner link B type | |||
| OBJECT-TYPE | |||
| INTEGER | sdlc(1), x25Qllc(2), frameRelayLLC2(3) | ||
| pktSwchSnaPULinkBRoleS | 1.3.6.1.4.1.164.8.11.3.1.7 | ||
| The PU role for link B. Note that the role of an SDLC PU may not be changed. It is defined by the SDLC Link Type. | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaPUEntryStatusS | 1.3.6.1.4.1.164.8.11.3.1.8 | ||
| The status of this PU table entry. This Set request will fail if there are any conflicts between any of of the parameter values in any of the tables comprising this PU definition | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchSnaPUTableA | 1.3.6.1.4.1.164.8.11.4 | ||
| The SDLC PU table defines the PUs configured on the PS. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUEntryA | |||
| pktSwchSnaPUEntryA | 1.3.6.1.4.1.164.8.11.4.1 | ||
| SDLC PU Entry defines the contents of each PU in the SDLC PU Table. | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUEntryA | |||
| pktSwchSnaPUNumberA | 1.3.6.1.4.1.164.8.11.4.1.1 | ||
| This parameter defines an identifier associated with the PU Entry which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUXIDProcessingA | 1.3.6.1.4.1.164.8.11.4.1.2 | ||
| The PU XID Processing | |||
| OBJECT-TYPE | |||
| INTEGER | localXid(1), end2EndSupNoAct(2), end2EndNoSupNoAct(3) | ||
| pktSwchSnaPUEnableA | 1.3.6.1.4.1.164.8.11.4.1.3 | ||
| The PU runs or not at this specific time | |||
| OBJECT-TYPE | |||
| INTEGER | enable(1), disable(2) | ||
| pktSwchSnaPULinkATypeA | 1.3.6.1.4.1.164.8.11.4.1.4 | ||
| The PU link type | |||
| OBJECT-TYPE | |||
| INTEGER | sdlc(1), x25Qllc(2), frameRelayLLC2(3) | ||
| pktSwchSnaPULinkARoleA | 1.3.6.1.4.1.164.8.11.4.1.5 | ||
| The PU role for link A | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaPULinkBTypeA | 1.3.6.1.4.1.164.8.11.4.1.6 | ||
| The PU partner link type | |||
| OBJECT-TYPE | |||
| INTEGER | sdlc(1), x25Qllc(2), frameRelayLLC2(3) | ||
| pktSwchSnaPULinkBRoleA | 1.3.6.1.4.1.164.8.11.4.1.7 | ||
| The PU role for link B | |||
| OBJECT-TYPE | |||
| INTEGER | primary(1), secondary(2) | ||
| pktSwchSnaPUSdlcTableS | 1.3.6.1.4.1.164.8.11.5 | ||
| Defines links for PUs running on SDLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUSdlcEntryS | |||
| pktSwchSnaPUSdlcEntryS | 1.3.6.1.4.1.164.8.11.5.1 | ||
| Defines parameters of a link for a PU running on an SDLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUSdlcEntryS | |||
| pktSwchSnaPUSdlcNumberS | 1.3.6.1.4.1.164.8.11.5.1.1 | ||
| This parameter defines an identifier associated with the PU Entry SDLC side, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcSideS | 1.3.6.1.4.1.164.8.11.5.1.2 | ||
| Is this side A or side B of the PU definition | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUSdlcAddressS | 1.3.6.1.4.1.164.8.11.5.1.3 | ||
| SNA SDLC PU address. Range: 0x00-0xFE | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUSdlcIfIndexS | 1.3.6.1.4.1.164.8.11.5.1.4 | ||
| ifIndex of the SDLC link | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcIdBlkS | 1.3.6.1.4.1.164.8.11.5.1.5 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idblk is required for secondary PU with Local XID handling. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPUSdlcIdNumS | 1.3.6.1.4.1.164.8.11.5.1.6 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idnum is required for secondary PU with Local XID handling. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPUSdlcMaxPiuSizeS | 1.3.6.1.4.1.164.8.11.5.1.7 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPUSdlcTxWindowS | 1.3.6.1.4.1.164.8.11.5.1.8 | ||
| Window Size(in frames) used when sending from the SPS. Range: 1-7. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcGrpAddressS | 1.3.6.1.4.1.164.8.11.5.1.9 | ||
| SNA Group address used by the SPS when sending polls (TPAD ONLY). Range: 0x00-0xFE | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUSdlcPollTimerS | 1.3.6.1.4.1.164.8.11.5.1.10 | ||
| Time in between polls in 50 millisecond increments (TPAD ONLY). Range: 1-65535. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcXIDInitiationS | 1.3.6.1.4.1.164.8.11.5.1.11 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to SDLC. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPUSdlcEntryStatusS | 1.3.6.1.4.1.164.8.11.5.1.12 | ||
| The status of this PU Sdlc table entry. In order to save this entry, set status to valid. An underCreation value is set by the Agent when this entry is updated. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchSnaPUSdlcTableA | 1.3.6.1.4.1.164.8.11.6 | ||
| Defines links for PUs running on an SDLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUSdlcEntryA | |||
| pktSwchSnaPUSdlcEntryA | 1.3.6.1.4.1.164.8.11.6.1 | ||
| Defines parameters of link for PU running on an SDLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUSdlcEntryA | |||
| pktSwchSnaPUSdlcNumberA | 1.3.6.1.4.1.164.8.11.6.1.1 | ||
| This parameter defines an identifier associated with the PU Entry SDLC side, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcSideA | 1.3.6.1.4.1.164.8.11.6.1.2 | ||
| Is this side A or side B of the PU definition | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUSdlcAddressA | 1.3.6.1.4.1.164.8.11.6.1.3 | ||
| SNA SDLC PU address. Range: 0x00-0xFE. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUSdlcIfIndexA | 1.3.6.1.4.1.164.8.11.6.1.4 | ||
| ifIndex of the SDLC link | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcIdBlkA | 1.3.6.1.4.1.164.8.11.6.1.5 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idblk is required for secondary PU with Local XID handling. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPUSdlcIdNumA | 1.3.6.1.4.1.164.8.11.6.1.6 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idnum is required for secondary PU with Local XID handling. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPUSdlcMaxPiuSizeA | 1.3.6.1.4.1.164.8.11.6.1.7 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPUSdlcTxWindowA | 1.3.6.1.4.1.164.8.11.6.1.8 | ||
| Window Size(in frames) used when sending from the SPS. Range: 1-7. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcGrpAddressA | 1.3.6.1.4.1.164.8.11.6.1.9 | ||
| SNA Group address used by the SPS when sending polls (TPAD ONLY). Range: 0x00-0xFE. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUSdlcPollTimerA | 1.3.6.1.4.1.164.8.11.6.1.10 | ||
| Time in between polls in 50 millisecond increments (TPAD ONLY). Range: 1-65535. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcXIDInitiationA | 1.3.6.1.4.1.164.8.11.6.1.11 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to SDLC. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPUSdlcStatTable | 1.3.6.1.4.1.164.8.11.7 | ||
| Shows Link Statistics for PUs running on an SDLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUSdlcStatEntry | |||
| pktSwchSnaPUSdlcStatEntry | 1.3.6.1.4.1.164.8.11.7.1 | ||
| Shows Link Statistics for PUs running on an SDLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUSdlcStatEntry | |||
| pktSwchSnaPUSdlcStatNumber | 1.3.6.1.4.1.164.8.11.7.1.1 | ||
| This parameter defines an identifier associated with the PU Entry SDLC side statistics, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUSdlcStatSide | 1.3.6.1.4.1.164.8.11.7.1.2 | ||
| Is this side A or side B of the PU definition | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUSdlcStatOctetsIn | 1.3.6.1.4.1.164.8.11.7.1.3 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatOctetsOut | 1.3.6.1.4.1.164.8.11.7.1.4 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatIFramesIn | 1.3.6.1.4.1.164.8.11.7.1.5 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatIFramesOut | 1.3.6.1.4.1.164.8.11.7.1.6 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRRFramesIn | 1.3.6.1.4.1.164.8.11.7.1.7 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRRFramesOut | 1.3.6.1.4.1.164.8.11.7.1.8 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRNRFramesIn | 1.3.6.1.4.1.164.8.11.7.1.9 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRNRFramesOut | 1.3.6.1.4.1.164.8.11.7.1.10 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatXIDsIn | 1.3.6.1.4.1.164.8.11.7.1.11 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatXIDsOut | 1.3.6.1.4.1.164.8.11.7.1.12 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatTESTsIn | 1.3.6.1.4.1.164.8.11.7.1.13 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatTESTsOut | 1.3.6.1.4.1.164.8.11.7.1.14 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatREJsIn | 1.3.6.1.4.1.164.8.11.7.1.15 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatREJsOut | 1.3.6.1.4.1.164.8.11.7.1.16 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatFRMRsIn | 1.3.6.1.4.1.164.8.11.7.1.17 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatFRMRsOut | 1.3.6.1.4.1.164.8.11.7.1.18 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatDISCsIn | 1.3.6.1.4.1.164.8.11.7.1.19 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatDISCsOut | 1.3.6.1.4.1.164.8.11.7.1.20 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatUAsIn | 1.3.6.1.4.1.164.8.11.7.1.21 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatUAsOut | 1.3.6.1.4.1.164.8.11.7.1.22 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatDMsIn | 1.3.6.1.4.1.164.8.11.7.1.23 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatDMsOut | 1.3.6.1.4.1.164.8.11.7.1.24 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatSNRMsIn | 1.3.6.1.4.1.164.8.11.7.1.25 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatSNRMsOut | 1.3.6.1.4.1.164.8.11.7.1.26 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRetransmitsIn | 1.3.6.1.4.1.164.8.11.7.1.27 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcStatRetransmitsOut | 1.3.6.1.4.1.164.8.11.7.1.28 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUSdlcUpperState | 1.3.6.1.4.1.164.8.11.7.1.29 | ||
| The internal DLPI state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | unbound(1), bindPending(2), unbindPend(3), idle(4), unattached(5), attachPend(6), detachPend(7), udqosPending(8), outconPend(9), inconPending(10), connResPend(11), dataxfer(12), userResetPend(13), provRstPend(14), rstResPend(15), discon8Pend(16), discon9Pend(17), discon11Pend(18), discon12Pend(19), discon13Pend(20), subsBindPnd(21), noChange(22) | ||
| pktSwchSnaPUSdlcLowerState | 1.3.6.1.4.1.164.8.11.7.1.30 | ||
| The internal SDLC state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | linkClosed(1), disconnected(2), linkOpening(3), disconnecting(4), frmrSent(5), linkOpened(6), localBusy(7), rejection(8), checkpointing(9), cpLocalBusy(10), cpRejection(11), resetting(12), remoteBusy(13), lBusyRBusy(14), rejLBusy(15), rejRBusy(16), cpRejLBusy(17), cpClearing(18), cpRejClr(19), rejLbusyRbusy(20), frmrReceived(21), programError(22), noChange(23) | ||
| pktSwchSnaPUSdlcStatNRMStatus | 1.3.6.1.4.1.164.8.11.7.1.31 | ||
| This variable indicates if the link is in Normal Response Mode or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(1), notSync(2) | ||
| pktSwchSnaPUSdlcStatFlowCtlStatus | 1.3.6.1.4.1.164.8.11.7.1.32 | ||
| This variable indicates the flow control status of the PU interface. | |||
| OBJECT-TYPE | |||
| INTEGER | noRNR(1), txFlow(2), rxFlow(3), rxAndTx(4) | ||
| pktSwchSnaPUSX25QllcTableS | 1.3.6.1.4.1.164.8.11.8 | ||
| Defines links for PUs running on a QLLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUX25QllcEntryS | |||
| pktSwchSnaPUX25QllcEntryS | 1.3.6.1.4.1.164.8.11.8.1 | ||
| Defines parameters for PU side running on SDLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUX25QllcEntryS | |||
| pktSwchSnaPUX25QllcNumberS | 1.3.6.1.4.1.164.8.11.8.1.1 | ||
| This parameter defines an identifier associated with the PU Entry X25\QLLC side, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcSideS | 1.3.6.1.4.1.164.8.11.8.1.2 | ||
| Is there side A or B of the PU connection | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUX25QllcIdBlkS | 1.3.6.1.4.1.164.8.11.8.1.3 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idblk is required for secondary PU with Local XID handling. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPUX25QllcIdNumS | 1.3.6.1.4.1.164.8.11.8.1.4 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idnum is required for secondary PU with Local XID handling. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPUX25QllcXIDInitS | 1.3.6.1.4.1.164.8.11.8.1.5 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to QLLC. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPUX25QllcMaxPiuSizeS | 1.3.6.1.4.1.164.8.11.8.1.6 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPUX25QllcStationAddressS | 1.3.6.1.4.1.164.8.11.8.1.7 | ||
| QLLC PU Link Station Address. Range: 0x01-0xFE. This parameter is applicable only for PU with End-to-End XID handling, Support for NON-Activation XID. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUX25QllcInPasswordS | 1.3.6.1.4.1.164.8.11.8.1.8 | ||
| A field matched with the call user data in call request packets for purposes of security and correlation. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..8) | ||
| pktSwchSnaPUX25QllcSubAddressS | 1.3.6.1.4.1.164.8.11.8.1.9 | ||
| The X.25 Sub-address associated with the PU Entry for routing incoming call indications. Range: 0-99. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcAutoCallS | 1.3.6.1.4.1.164.8.11.8.1.10 | ||
| This parameter indicates whether the SPS automatically initiates an X.25 call request or not. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(1), no(2) | ||
| pktSwchSnaPUX25QllcCalledAddressS | 1.3.6.1.4.1.164.8.11.8.1.11 | ||
| The destination x.25 DTE address to which the SPS calls. Used with AutoCall only. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..15) | ||
| pktSwchSnaPUX25QllcCallUserDataFacilitiesS | 1.3.6.1.4.1.164.8.11.8.1.12 | ||
| The X.25 facilities and Call User Data which the SPS uses on outgoing calls. AutoCall only. Up to 60 Hexa-Decimal digits. Each pair of digits represents a BYTE. BYTE-0 BYTE-1 BYTE-2 ... BYTE-29 (30 Bytes maximum) BYTE-0 for X.25 Facilities. BYTE-1 to BYTE-29 for Call User Data. Facilities (BYTE-0) format: PW (Hexa-Decimal), where: X.25 L3 Packet Size Negotiation : [P=1 YES] [P=0 NO]. X.25 L3 Packet Window Negotiation : [W=1 YES] [W=0 NO]. Legal Values for Facilities BYTE-0 : 10, 01, 11, 00 (Hex). ATTENTION: a. Total number of digits in this field must be EVEN. b. To clear this field, enter blanks or 00. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..60) | ||
| pktSwchSnaPUX25QllcEntryStatusS | 1.3.6.1.4.1.164.8.11.8.1.13 | ||
| The status of this PU Qllc table entry. In order to save this entry, set status to valid. An underCreation value is set by the Agent when this entry is updated. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchSnaPUX25QllcTableA | 1.3.6.1.4.1.164.8.11.9 | ||
| Defines links for PUs running on a QLLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUX25QllcEntryA | |||
| pktSwchSnaPUX25QllcEntryA | 1.3.6.1.4.1.164.8.11.9.1 | ||
| Defines parameters for PU side running on an SDLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUX25QllcEntryA | |||
| pktSwchSnaPUX25QllcNumberA | 1.3.6.1.4.1.164.8.11.9.1.1 | ||
| This parameter defines an identifier associated with the PU Entry X25\QLLC side, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcSideA | 1.3.6.1.4.1.164.8.11.9.1.2 | ||
| Is there side A or B of the PU connection | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUX25QllcIdBlkA | 1.3.6.1.4.1.164.8.11.9.1.3 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idblk is required for secondary PU with Local XID handling. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPUX25QllcIdNumA | 1.3.6.1.4.1.164.8.11.9.1.4 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The Idnum is required for secondary PU with Local XID handling. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPUX25QllcXIDInitA | 1.3.6.1.4.1.164.8.11.9.1.5 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to QLLC. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPUX25QllcMaxPiuSizeA | 1.3.6.1.4.1.164.8.11.9.1.6 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPUX25QllcStationAddressA | 1.3.6.1.4.1.164.8.11.9.1.7 | ||
| QLLC PU Link Station Address. Range: 0x01-0xFE. This parameter is applicable only for PU with End-to-End XID handling, Support for NON-Activation XID. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPUX25QllcInPasswordA | 1.3.6.1.4.1.164.8.11.9.1.8 | ||
| A field matched with the call user data in call request packets for purposes of security and correlation. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..8) | ||
| pktSwchSnaPUX25QllcSubAddressA | 1.3.6.1.4.1.164.8.11.9.1.9 | ||
| The X.25 Sub-address associated with the PU Entry for routing incoming call indications. Range: 0-99. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcAutoCallA | 1.3.6.1.4.1.164.8.11.9.1.10 | ||
| This parameter indicates whether the SPS automatically initiates an X.25 call request or not. | |||
| OBJECT-TYPE | |||
| INTEGER | yes(1), no(2) | ||
| pktSwchSnaPUX25QllcCalledAddressA | 1.3.6.1.4.1.164.8.11.9.1.11 | ||
| The destination x.25 DTE address to which the SPS calls. Used with AutoCall only. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..15) | ||
| pktSwchSnaPUX25QllcCallUserDataFacilitiesA | 1.3.6.1.4.1.164.8.11.9.1.12 | ||
| The X.25 facilities and Call User Data which the SPS uses on outgoing calls. AutoCall only. Up to 60 Hexa-Decimal digits. Each pair of digits represents a BYTE. BYTE-0 BYTE-1 BYTE-2 ... BYTE-29 (30 Bytes maximum) BYTE-0 for X.25 Facilities. BYTE-1 to BYTE-29 for Call User Data. Facilities (BYTE-0) format: PW (Hexa-Decimal), where: X.25 L3 Packet Size Negotiation : [P=1 YES] [P=0 NO]. X.25 L3 Packet Window Negotiation : [W=1 YES] [W=0 NO]. Legal Values for Facilities BYTE-0 : 10, 01, 11, 00 (Hex). ATTENTION: a. Total number of digits in this field must be EVEN. b. To clear this field, enter blanks or 00. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(1..60) | ||
| pktSwchSnaPUX25QllcStatTable | 1.3.6.1.4.1.164.8.11.10 | ||
| Shows link statistics for PUs running on a QLLC link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPUX25QllcStatEntry | |||
| pktSwchSnaPUX25QllcStatEntry | 1.3.6.1.4.1.164.8.11.10.1 | ||
| Shows link statistics for PUs running on a QLLC link | |||
| OBJECT-TYPE | |||
| PktSwchSnaPUX25QllcStatEntry | |||
| pktSwchSnaPUX25QllcStatNumber | 1.3.6.1.4.1.164.8.11.10.1.1 | ||
| This parameter defines an identifier associated with the PU Entry X25\QLLC side, which is unique within the SPS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcStatSide | 1.3.6.1.4.1.164.8.11.10.1.2 | ||
| Is there side A or B of the PU connection | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPUX25QllcStatlink | 1.3.6.1.4.1.164.8.11.10.1.3 | ||
| The Link on which the Qllc conversation is conducted. If there is no conversation the variable will be 0. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPUX25QllcStatDataPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.4 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatDataPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.5 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQSMPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.6 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQSMPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.7 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQDMPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.8 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQDMPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.9 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatXIDPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.10 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatXIDPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.11 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQDISCPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.12 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatQDISCPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.13 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatCallPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.14 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatCallPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.15 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatClearPacketsIn | 1.3.6.1.4.1.164.8.11.10.1.16 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatClearPacketsOut | 1.3.6.1.4.1.164.8.11.10.1.17 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatCallAcceptsIn | 1.3.6.1.4.1.164.8.11.10.1.18 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatCallAcceptsOut | 1.3.6.1.4.1.164.8.11.10.1.19 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPUX25QllcStatUpperState | 1.3.6.1.4.1.164.8.11.10.1.20 | ||
| The internal DLPI state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | unbound(1), bindPending(2), unbindPend(3), idle(4), unattached(5), attachPend(6), detachPend(7), udqosPending(8), outconPend(9), inconPending(10), connResPend(11), dataxfer(12), userResetPend(13), provRstPend(14), rstResPend(15), discon8Pend(16), discon9Pend(17), discon11Pend(18), discon12Pend(19), discon13Pend(20), subsBindPnd(21), noChange(22) | ||
| pktSwchSnaPUX25QllcStatLowerState | 1.3.6.1.4.1.164.8.11.10.1.21 | ||
| The internal QLLC state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | linkClosed(1), disconnected(2), linkOpening(3), disconnecting(4), frmrSent(5), linkOpened(6), localBusy(7), rejection(8), checkpointing(9), cpLocalBusy(10), cpRejection(11), resetting(12), remoteBusy(13), lBusyRBusy(14), rejLBusy(15), rejRBusy(16), cpRejLBusy(17), cpClearing(18), cpRejClr(19), rejLbusyRbusy(20), frmrReceived(21), programError(22), noChange(23) | ||
| pktSwchSnaPUX25QllcStatNRMStatus | 1.3.6.1.4.1.164.8.11.10.1.22 | ||
| This variable indicates if the link is in Normal Response Mode or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(1), notSync(2) | ||
| pktSwchSnaPUX25QllcStatFlowCtlStatus | 1.3.6.1.4.1.164.8.11.10.1.23 | ||
| This variable indicates the flow control status of the PU interface. | |||
| OBJECT-TYPE | |||
| INTEGER | noRNR(1), txFlow(2), rxFlow(3), rxAndTx(4) | ||
| pktSwchSnaPULlc2FrTableS | 1.3.6.1.4.1.164.8.11.11 | ||
| Defines LLC2/Frame Relay/RFC1490 Protocol Interface of SPS SNA PU entity. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPULlc2FrEntryS | |||
| pktSwchSnaPULlc2FrEntryS | 1.3.6.1.4.1.164.8.11.11.1 | ||
| Defines parameters for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490. | |||
| OBJECT-TYPE | |||
| PktSwchSnaPULlc2FrEntryS | |||
| pktSwchSnaPULlc2FrNumberS | 1.3.6.1.4.1.164.8.11.11.1.1 | ||
| Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrSideS | 1.3.6.1.4.1.164.8.11.11.1.2 | ||
| Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPULlc2FrEncapsTypeS | 1.3.6.1.4.1.164.8.11.11.1.3 | ||
| Indicates if the LLC2/RFC1490 Protocol Interface uses the BNN, BAN or TREN method of Frame Encapsulation. | |||
| OBJECT-TYPE | |||
| INTEGER | ban(1), bnn(2), tren(3) | ||
| pktSwchSnaPULlc2FrDestMACS | 1.3.6.1.4.1.164.8.11.11.1.4 | ||
| The LLC2 Destination MAC Address. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchSnaPULlc2FrSrcSAPS | 1.3.6.1.4.1.164.8.11.11.1.5 | ||
| The LLC2 Source SAP Address. 2 Hex digits | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPULlc2FrDestSAPS | 1.3.6.1.4.1.164.8.11.11.1.6 | ||
| The LLC2 Destination SAP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPULlc2FrXIDIdBlkS | 1.3.6.1.4.1.164.8.11.11.1.7 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDBLK is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPULlc2FrXIDIdNumS | 1.3.6.1.4.1.164.8.11.11.1.8 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDNUM is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPULlc2FrMaxPiuSizeS | 1.3.6.1.4.1.164.8.11.11.1.9 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPULlc2FrTxWindowS | 1.3.6.1.4.1.164.8.11.11.1.10 | ||
| The LLC2 Link Window Size. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrLinkS | 1.3.6.1.4.1.164.8.11.11.1.11 | ||
| The SPS Frame Relay Link Number which this LLC2 Protocol Interface is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrDLCIS | 1.3.6.1.4.1.164.8.11.11.1.12 | ||
| The SPS Frame Relay DLCI Number which this LLC2 Protocol Interface is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrXIDInitiationS | 1.3.6.1.4.1.164.8.11.11.1.13 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to LLC2. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPULlc2FrN2CountS | 1.3.6.1.4.1.164.8.11.11.1.14 | ||
| N2 Count | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrT1TimerS | 1.3.6.1.4.1.164.8.11.11.1.15 | ||
| T1 Timer in 1/10 of a second. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrTiTimerS | 1.3.6.1.4.1.164.8.11.11.1.16 | ||
| TI Timer in seconds | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrEntryStatusS | 1.3.6.1.4.1.164.8.11.11.1.17 | ||
| The status of this PU Llc2 table entry. In order to save this entry, set status to valid. An underCreation value is set by the Agent when this entry is updated. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchSnaPULlc2FrTableA | 1.3.6.1.4.1.164.8.11.12 | ||
| Defines links for PUs running on an LLC2 link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPULlc2FrEntryA | |||
| pktSwchSnaPULlc2FrEntryA | 1.3.6.1.4.1.164.8.11.12.1 | ||
| Defines parameters for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490. | |||
| OBJECT-TYPE | |||
| PktSwchSnaPULlc2FrEntryA | |||
| pktSwchSnaPULlc2FrNumberA | 1.3.6.1.4.1.164.8.11.12.1.1 | ||
| Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrSideA | 1.3.6.1.4.1.164.8.11.12.1.2 | ||
| Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPULlc2FrEncapsTypeA | 1.3.6.1.4.1.164.8.11.12.1.3 | ||
| Indicates if the LLC2/RFC1490 Protocol Interface uses the BNN, BAN or TREN method of Frame Encapsulation. | |||
| OBJECT-TYPE | |||
| INTEGER | ban(1), bnn(2), tren(3) | ||
| pktSwchSnaPULlc2FrDestMACA | 1.3.6.1.4.1.164.8.11.12.1.4 | ||
| The LLC2 Destination MAC Address. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchSnaPULlc2FrSrcSAPA | 1.3.6.1.4.1.164.8.11.12.1.5 | ||
| The LLC2 Source SAP Address. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPULlc2FrDestSAPA | 1.3.6.1.4.1.164.8.11.12.1.6 | ||
| The LLC2 Destination SAP. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| pktSwchSnaPULlc2FrXIDIdBlkA | 1.3.6.1.4.1.164.8.11.12.1.7 | ||
| Part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDBLK is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 3 Hexadecimal digits, format: 0X XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..2) | ||
| pktSwchSnaPULlc2FrXIDIdNumA | 1.3.6.1.4.1.164.8.11.12.1.8 | ||
| Second part of the IBM device ID (the full ID is defined by the IDBLK and the IDNUM). The IDNUM is required for PU with Local XID handling or PU with End-to-End XID handling, NO Support for NON-Activation XID. Up to 5 Hexadecimal digits, format: 0X XX XX. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1..3) | ||
| pktSwchSnaPULlc2FrMaxPiuSizeA | 1.3.6.1.4.1.164.8.11.12.1.9 | ||
| Maximum Path Information Size | |||
| OBJECT-TYPE | |||
| Integer32 | 137..7642 | ||
| pktSwchSnaPULlc2FrTxWindowA | 1.3.6.1.4.1.164.8.11.12.1.10 | ||
| The LLC2 Link Window Size. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrLinkA | 1.3.6.1.4.1.164.8.11.12.1.11 | ||
| The SPS Frame Relay Link Number which this LLC2 Protocol Interface is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrDLCIA | 1.3.6.1.4.1.164.8.11.12.1.12 | ||
| The SPS Frame Relay DLCI Number which this LLC2 Protocol Interface is associated with. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrXIDInitiationA | 1.3.6.1.4.1.164.8.11.12.1.13 | ||
| This parameter is not applicable for PU with Local XID handling. Legal values: 1 - Do not initiate an XID message. 2 - Initiate an XID message to LLC2. | |||
| OBJECT-TYPE | |||
| INTEGER | notInitiate(1), initiate(2) | ||
| pktSwchSnaPULlc2FrN2CountA | 1.3.6.1.4.1.164.8.11.12.1.14 | ||
| N2 Count | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrT1TimerA | 1.3.6.1.4.1.164.8.11.12.1.15 | ||
| T1 Timer in 1/10 of a second. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrTiTimerA | 1.3.6.1.4.1.164.8.11.12.1.16 | ||
| TI Timer in seconds | |||
| OBJECT-TYPE | |||
| Integer32 | 1..99999 | ||
| pktSwchSnaPULlc2FrStatTable | 1.3.6.1.4.1.164.8.11.13 | ||
| Shows link statistics for PUs running on an LLC2 link | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchSnaPULlc2FrStatEntry | |||
| pktSwchSnaPULlc2FrStatEntry | 1.3.6.1.4.1.164.8.11.13.1 | ||
| Shows statistics for PU LLC2 Protocol Interface over Frame Relay Protocol using RFC 1490. | |||
| OBJECT-TYPE | |||
| PktSwchSnaPULlc2FrStatEntry | |||
| pktSwchSnaPULlc2FrStatNumber | 1.3.6.1.4.1.164.8.11.13.1.1 | ||
| Unique Identifier for this PU. The value in this field is used as a common Key in both this table and the Main PU table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaPULlc2FrStatSide | 1.3.6.1.4.1.164.8.11.13.1.2 | ||
| Indicates for each side (SIDE-A and SIDE-B) if the Protocol Interface for that side has been defined or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sideA(1), sideB(2) | ||
| pktSwchSnaPULlc2FrStatOctetsIn | 1.3.6.1.4.1.164.8.11.13.1.3 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatOctetsOut | 1.3.6.1.4.1.164.8.11.13.1.4 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatIFramesIn | 1.3.6.1.4.1.164.8.11.13.1.5 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatIFramesOut | 1.3.6.1.4.1.164.8.11.13.1.6 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRRFramesIn | 1.3.6.1.4.1.164.8.11.13.1.7 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRRFramesOut | 1.3.6.1.4.1.164.8.11.13.1.8 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRNRFramesIn | 1.3.6.1.4.1.164.8.11.13.1.9 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRNRFramesOut | 1.3.6.1.4.1.164.8.11.13.1.10 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatXIDsIn | 1.3.6.1.4.1.164.8.11.13.1.11 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatXIDsOut | 1.3.6.1.4.1.164.8.11.13.1.12 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatTESTsIn | 1.3.6.1.4.1.164.8.11.13.1.13 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatTESTsOut | 1.3.6.1.4.1.164.8.11.13.1.14 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatREJsIn | 1.3.6.1.4.1.164.8.11.13.1.15 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatREJsOut | 1.3.6.1.4.1.164.8.11.13.1.16 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatFRMRsIn | 1.3.6.1.4.1.164.8.11.13.1.17 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatFRMRsOut | 1.3.6.1.4.1.164.8.11.13.1.18 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatDISCsIn | 1.3.6.1.4.1.164.8.11.13.1.19 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatDISCsOut | 1.3.6.1.4.1.164.8.11.13.1.20 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatUAsIn | 1.3.6.1.4.1.164.8.11.13.1.21 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatUAsOut | 1.3.6.1.4.1.164.8.11.13.1.22 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatDMsIn | 1.3.6.1.4.1.164.8.11.13.1.23 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatDMsOut | 1.3.6.1.4.1.164.8.11.13.1.24 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatSABMEsIn | 1.3.6.1.4.1.164.8.11.13.1.25 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatSABMEsOut | 1.3.6.1.4.1.164.8.11.13.1.26 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRetransmitsIn | 1.3.6.1.4.1.164.8.11.13.1.27 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatRetransmitsOut | 1.3.6.1.4.1.164.8.11.13.1.28 | ||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchSnaPULlc2FrStatUpperState | 1.3.6.1.4.1.164.8.11.13.1.29 | ||
| The internal DLPI state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | unbound(1), bindPending(2), unbindPend(3), idle(4), unattached(5), attachPend(6), detachPend(7), udqosPending(8), outconPend(9), inconPending(10), connResPend(11), dataxfer(12), userResetPend(13), provRstPend(14), rstResPend(15), discon8Pend(16), discon9Pend(17), discon11Pend(18), discon12Pend(19), discon13Pend(20), subsBindPend(21), noChange(22) | ||
| pktSwchSnaPULlc2FrStatLowerState | 1.3.6.1.4.1.164.8.11.13.1.30 | ||
| The internal Llc2Fr state of the connection. | |||
| OBJECT-TYPE | |||
| INTEGER | linkClosed(1), disconnected(2), linkOpening(3), disconnecting(4), frmrSent(5), linkOpened(6), localBusy(7), rejection(8), checkpointing(9), cpLocalBusy(10), cpRejection(11), resetting(12), remoteBusy(13), lBusyRBusy(14), rejLBusy(15), rejRBusy(16), cpRejLBusy(17), cpClearing(18), cpRejClr(19), rejLbusyRbusy(20), frmrReceived(21), programError(22), noChange(23) | ||
| pktSwchSnaPULlc2FrStatNRMStatus | 1.3.6.1.4.1.164.8.11.13.1.31 | ||
| This variable indicates if the link is in Normal Response Mode or not. | |||
| OBJECT-TYPE | |||
| INTEGER | sync(1), notSync(2) | ||
| pktSwchSnaPULlc2FrStatFlowCtlStatus | 1.3.6.1.4.1.164.8.11.13.1.32 | ||
| This variable indicates the flow control status of the PU interface. | |||
| OBJECT-TYPE | |||
| INTEGER | noRNR(1), txFlow(2), rxFlow(3), rxAndTx(4) | ||
| pktSwchSnaGlobal | 1.3.6.1.4.1.164.8.11.14 | ||
| OBJECT IDENTIFIER | |||
| pktSwchSnaGlobalSrcMacAddrS | 1.3.6.1.4.1.164.8.11.14.1 | ||
| LLC2 source MAC address used for all LLC2\RFC1490 protocol interfaces, Scratch variable. Format: XX XX XX XX XX XX | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchSnaGlobalSrcMacAddrA | 1.3.6.1.4.1.164.8.11.14.2 | ||
| LLC2 source MAC address used for all LLC2\RFC1490 protocol interfaces, Active variable. Format: XX XX XX XX XX XX | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchSnaGlobalDefFrLlc2LinkS | 1.3.6.1.4.1.164.8.11.14.3 | ||
| The FR Link to where a mac frame will be routed when the destination MAC address of the frame does not match the SPS source mac address. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaGlobalDefFrLlc2LinkA | 1.3.6.1.4.1.164.8.11.14.4 | ||
| The FR Link to where a mac frame will be routed when the destination MAC address of the frame does not match the SPS source mac address. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaGlobalDefFrLlc2DlciS | 1.3.6.1.4.1.164.8.11.14.5 | ||
| The FR DLCI to where a mac frame will be routed when the destination MAC address of the frame does not match the SPS source mac address. DLCI range is 16..991. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaGlobalDefFrLlc2DlciA | 1.3.6.1.4.1.164.8.11.14.6 | ||
| The FR DLCI to where a mac frame will be routed when the destination MAC address of the frame does not match the SPS source mac address. DLCI range is 16..991. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaGlobalMaxPus | 1.3.6.1.4.1.164.8.11.14.7 | ||
| The maximum number of PUs that can be defined on this device. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchSnaGlobalStatus | 1.3.6.1.4.1.164.8.11.14.8 | ||
| The status of this SNA Global entry. Used for saving the mac address, llc2 port, and dlci. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchEthernet | 1.3.6.1.4.1.164.8.12 | ||
| OBJECT IDENTIFIER | |||
| pktSwchEthernetLinkTable | 1.3.6.1.4.1.164.8.12.1 | ||
| The Ethernet link table defines the parameters in the PS Ethernet links. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchEthernetLinkEntry | |||
| pktSwchEthernetLinkEntry | 1.3.6.1.4.1.164.8.12.1.1 | ||
| The Ethernet Link Entry defines the contents of each link in the Ethernet Link Table. | |||
| OBJECT-TYPE | |||
| PktSwchEthernetLinkEntry | |||
| pktSwchEthernetLinkOperationMode | 1.3.6.1.4.1.164.8.12.1.1.1 | ||
| This parameter shows the frame handling mode on this link. When IP mode is defined, the IP frames received on this link are handled and routed by the IP module in the PS. If IP mode is disabled, the IP frames will not be handled by the IP module and will be handled as bridged data. When Bridging mode is enabled, the PS will perform bridging from this link according to the bridging configuration. If disabled, bridge data will be ignored. When LLC is enabled, frames received on this link are handled by the LLC module in the PS. If disabled, the LLC frames will be treated as bridged data. Any combination of bridging, ip and LLC is allowed. If both IP and LLC are enabled, LLC frames will be handled by the LLC module, IP frames will be handled by the IP module, and all the other frames will treated as bridged data. If the bridge mode is disabled, the other frames will be discarded. | |||
| OBJECT-TYPE | |||
| INTEGER | bridging(3), ip(4), ip-and-bridging(7), llc(8), llc-and-bridging(11), ip-and-llc(12), all(15), none(255) | ||
| pktSwchEthernetLinkUserDefMacAddr | 1.3.6.1.4.1.164.8.12.1.1.2 | ||
| This parameter allows the user to define a different MAC address for this link other than the device MAC address. Possible values: 6 sets of 2 Hexadecimal digits with spaces between them (XX XX XX XX XX XX) | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchEthernetLinkPointToPointDest | 1.3.6.1.4.1.164.8.12.1.1.3 | ||
| Destination of the frames which are received on this link. Possible values: X.25 PVC: Port:LCN X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID number. Frame Relay: Port:DLCI No Destination: None If no destination, frames will be forwarded according to the filter table in 1st priority. If no filter match, the frames will be forwarded according to dynamic learning. Default value: None | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchEthernetLinkTotalFramesIn | 1.3.6.1.4.1.164.8.12.1.1.4 | ||
| Total number of frames which were received on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkTotalFramesOut | 1.3.6.1.4.1.164.8.12.1.1.5 | ||
| Total number of frames which were transmitted from this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkIpFramesIn | 1.3.6.1.4.1.164.8.12.1.1.6 | ||
| Number of IP frames which were received on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkIpFramesOut | 1.3.6.1.4.1.164.8.12.1.1.7 | ||
| Number of IP frames which were transmitted from this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkLlc2FramesIn | 1.3.6.1.4.1.164.8.12.1.1.8 | ||
| Number of LLC2 frames which were received on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkLlc2FramesOut | 1.3.6.1.4.1.164.8.12.1.1.9 | ||
| Number of LLC2 frames which were transmitted from this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkBridgFramesIn | 1.3.6.1.4.1.164.8.12.1.1.10 | ||
| Number of Bridged frames which were received on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkBridgFramesOut | 1.3.6.1.4.1.164.8.12.1.1.11 | ||
| Number of Bridged frames which were transmitted from this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetLinkDiscardedByFilter | 1.3.6.1.4.1.164.8.12.1.1.12 | ||
| Number of Bridged frames which were received on this link. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchEthernetFilterTable | 1.3.6.1.4.1.164.8.12.2 | ||
| The Ethernet filter table defines the frame filtering and routing through the PS Ethernet links. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchEthernetFilterEntry | |||
| pktSwchEthernetFilterEntry | 1.3.6.1.4.1.164.8.12.2.1 | ||
| The Ethernet Filter Entry defines the filtering on each Ethernet link. The filter entry is operational only if Bridging Handling is enabled and there is no point to point destination configured for this link. If there is a point to point destination configured, the frames will be directed to this destination. | |||
| OBJECT-TYPE | |||
| PktSwchEthernetFilterEntry | |||
| pktSwchEthernetFilterId | 1.3.6.1.4.1.164.8.12.2.1.1 | ||
| Identification Number of an entry in the filter table. The ID together with the ifindex define an entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| pktSwchEthernetFilterMacAddr | 1.3.6.1.4.1.164.8.12.2.1.2 | ||
| This parameter defines the MAC address in the current entry of the filter table. The MAC address in the filter table is compared with the MAC address in the received frame. If the MAC address and protocol type of the frame are equal to the values in the filter table, the frame will be directed to the destination address specified in the filter table. Possible values: MAC Address : 6 sets of 2 Hexadecimal digits with spaces between them (XX XX XX XX XX XX) Broadcasting: FF FF FF FF FF FF Don't Care : 00 00 00 00 00 00 For Broadcasting: If a broadcasting entry contains a destination, the frame will not be broadcasted. It will be directed to the destination in this entry. For Don't care: The MAC address in the frame and in the filter table are not compared. The frames will be directed to the destination specified in the filter table if there is a match between the protocol types in the frame and in the filter table. Default value: 00 00 00 00 00 00 | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(6) | ||
| pktSwchEthernetFilterProtType | 1.3.6.1.4.1.164.8.12.2.1.3 | ||
| The protocol type which is compared with the protocol type in the received frame. Each protocol in the IP frame is assigned 16 bits (see RFC1700.txt on the assignment of protocol parameters for the Internet protocol suite.). If 65535 is entered for the protocol, it means Don't Care. If there is a match between this protocol and the protocol in the received frame and a match in the MAC addresses, the frame will be directed to the destination specified in this table. Default value: dontCare (65535). | |||
| OBJECT-TYPE | |||
| INTEGER | llc(256), ip(2048), arp(2054), appleTalk(32923), dontCare(65535) | ||
| pktSwchEthernetFilterDest | 1.3.6.1.4.1.164.8.12.2.1.4 | ||
| Destination of the frames which match this current entry. The match is in the MAC address and protocol. Possible values: X.25 PVC: Port:LCN X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID number Frame Relay: Port:DLCI No Destination: None If No Destination, the frames will be discarded. Default value: None . | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchEthernetFilterStatus | 1.3.6.1.4.1.164.8.12.2.1.5 | ||
| The status of this filter table entry. valid - This entry was saved. createRequest - Request to create a new entry. underCreation - For a new/updated entry. invalid - Entry is deleted. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchEthernetBridging | 1.3.6.1.4.1.164.8.12.3 | ||
| OBJECT IDENTIFIER | |||
| pktSwchEthernetBridgingWanToWan | 1.3.6.1.4.1.164.8.12.3.1 | ||
| Enable/Disable Ethernet Bridging, WAN to WAN. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| pktSwchEthernetBridgingTimer | 1.3.6.1.4.1.164.8.12.3.2 | ||
| Timer used for WAN to WAN communication in order to prevent broadcast frames looping forever between devices. When the timer expires, the frames are discarded. Possible values: 0 - No timer is used. 1..255 - Timer value in units of 100 mili sec. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchEthernetBridgingStatus | 1.3.6.1.4.1.164.8.12.3.3 | ||
| The status of the Ethernet Bridging Parameters. valid - This table was saved. underCreation - The table was updated and not yet saved. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchEthernetBroadcastDestTable | 1.3.6.1.4.1.164.8.12.4 | ||
| The Ethernet Broadcast Destination table defines all the Bridging destinations of the PS. Each Broadcasted frame will be broadcasted to all these destinations. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchEthernetBroadcastDestEntry | |||
| pktSwchEthernetBroadcastDestEntry | 1.3.6.1.4.1.164.8.12.4.1 | ||
| The Ethernet Broadcast Entry defines destinations for Ethernet bridge data. | |||
| OBJECT-TYPE | |||
| PktSwchEthernetBroadcastDestEntry | |||
| pktSwchEthernetBroadcastDestProtocol | 1.3.6.1.4.1.164.8.12.4.1.1 | ||
| The protocol of the Broadcasted frames. | |||
| OBJECT-TYPE | |||
| INTEGER | x25(2), frameRelay(3) | ||
| pktSwchEthernetBroadcastDestId | 1.3.6.1.4.1.164.8.12.4.1.2 | ||
| Identification Number of an entry in the Ethernet Broadcast Destination table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..10 | ||
| pktSwchEthernetBroadcastDestDestination | 1.3.6.1.4.1.164.8.12.4.1.3 | ||
| Destination for the Ethernet frames. Possible values for X25: X.25 PVC: Port:LCN X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID number Possible values for fr: Frame Relay: Port:DLCI No Destination: None | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchEthernetBroadcastDestStatus | 1.3.6.1.4.1.164.8.12.4.1.4 | ||
| The status of this Ethernet Destination table entry. valid - This entry was saved. createRequest - Request to create a new entry. underCreation - For a new/updated entry. invalid - Entry is deleted. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIp | 1.3.6.1.4.1.164.8.13 | ||
| OBJECT IDENTIFIER | |||
| pktSwchIpGlobal | 1.3.6.1.4.1.164.8.13.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchIpGlobalMaxHopCount | 1.3.6.1.4.1.164.8.13.1.1 | ||
| Maximum no. of hops the device will support. The default value is 15. Legal values: 5 to 65000. | |||
| OBJECT-TYPE | |||
| Integer32 | 5..65000 | ||
| pktSwchIpIntervalBetweenUpdates | 1.3.6.1.4.1.164.8.13.1.2 | ||
| The time in seconds from one update of the device's dynamic routing table to the next update. The time is in steps of 10 seconds. Default value: 30 Legal values: 30,40,50 ... 2550 | |||
| OBJECT-TYPE | |||
| Integer32 | 30..2550 | ||
| pktSwchIpGlobalStatus | 1.3.6.1.4.1.164.8.13.1.3 | ||
| The status of this IP Global entry. Used for saving the IP Global parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchIpInterfaceTable | 1.3.6.1.4.1.164.8.13.2 | ||
| The Ip interface table defines the Ip interfaces and their parameters in the PS device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIpInterfaceEntry | |||
| pktSwchIpInterfaceEntry | 1.3.6.1.4.1.164.8.13.2.1 | ||
| The IP interface Entry defines the IP configuration parameters for each IP interface. | |||
| OBJECT-TYPE | |||
| PktSwchIpInterfaceEntry | |||
| pktSwchIpInterfaceId | 1.3.6.1.4.1.164.8.13.2.1.1 | ||
| Identification Number of an entry in the IP interface table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIpInterfaceAddress | 1.3.6.1.4.1.164.8.13.2.1.2 | ||
| The IP address of the interface. Legal input: any legal IP address. Default value: 0.0.0.0 | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpInterfaceAddressMask | 1.3.6.1.4.1.164.8.13.2.1.3 | ||
| The IP mask of the interface. Legal input: any legal IP mask: A string of the format X.X.X.X where every X is a number in the range 0-255. Default value: 255.255.255.255 | |||
| OBJECT-TYPE | |||
| IpAddress | |||
| pktSwchIpInterfaceSendDefRoutMsgOnly | 1.3.6.1.4.1.164.8.13.2.1.4 | ||
| Some of the RIP messages are default router messages. These messages inform who the default router is. This MIB object allows the user to configure the device so that it will send default router messages only. If sendDefaultRoutMsgOnly is set to enable, the device will not send any RIP messages except for default router messages. Default value: disable . | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| pktSwchIpInterfaceDest | 1.3.6.1.4.1.164.8.13.2.1.5 | ||
| Destination of the packets received on this interface. Possible values: X.25 PVC: Port:LCN X.25 SVC: X.25 Addr or 'cid' followed by a predefined Call ID number. Frame Relay: Port:DLCI HDLC: 'H' followed by the HDLC Port Number SLIP: 'S' followed by the SLIP Channel Number Ethernet: 'E' followed by the Ethernet Port Number PPP: 'P' followed by the PPP Port Number. Bundles(for PPP)'B' followed by the PPP Bundle Number. No destination: None Default : None Examples: 1. For SLIP destination which is Link no. 1, the destination will be S100 (100 instead of 1 is for Async). 2. For SLIP destination of APS-8, channel no. 8: S8 3. For PPP destination of APS-8, Sync Link no. 1: P1 4. For PPP destination of APS-8, Async channel on link 1: P100 Note for PPP: PPP protocol is allowed to be applied on Sync Links (1-3) as well as Async channels (1-24). In the ascii terminal: If the user writes P1 for example the device has to check which P1 it is. Is it the async channel 1 or Link no. 1. The device does NOT ALLOW configuring PPP on both Sync Link no. 1 and async RJ45 channel 1. When P1 is entered by the user, the protocols on async channel 1 and sync link 1 are checked. As only one of them is PPP, it will apply to the only PPP chan/link. | |||
| OBJECT-TYPE | |||
| DisplayString | |||
| pktSwchIpInterfaceInactivity | 1.3.6.1.4.1.164.8.13.2.1.6 | ||
| Inactivity time in minutes before disconnecting the X25 SVC call. Range: 0..255. Default: 2. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchIpInterfaceLinkCost | 1.3.6.1.4.1.164.8.13.2.1.7 | ||
| This value will be added to the value written in the metric field of the received frame. Range: 1..pktSwchIpGlobalMaxHopCount Default: 1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| pktSwchIpInterfaceOptions | 1.3.6.1.4.1.164.8.13.2.1.8 | ||
| When netIpAddress is selected the interface IP address will not be the IP address of the interface. It will be the IP address of the NetWork which is connected to this interface. This option is for an interface which does not require a unique IP address. Default is none. | |||
| OBJECT-TYPE | |||
| INTEGER | netIpAddress(2), none(255) | ||
| pktSwchIpInterfaceStatus | 1.3.6.1.4.1.164.8.13.2.1.9 | ||
| The status of this filter table entry. valid - This entry was saved. createRequest - Request to create a new entry. underCreation - For a new/updated entry. invalid - Entry is deleted. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIpInterfaceRxFrames | 1.3.6.1.4.1.164.8.13.2.1.10 | ||
| No. of frames which were received on this IP interface. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceRxExpiredTtl | 1.3.6.1.4.1.164.8.13.2.1.11 | ||
| No. of frames which were received on this IP interface with an Expired Time to Live value. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceRxUnknownDest | 1.3.6.1.4.1.164.8.13.2.1.12 | ||
| No. of frames which were received on this IP interface with an unknown IP destination. No default router is configured. These frames will be discarded. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceTxFrames | 1.3.6.1.4.1.164.8.13.2.1.13 | ||
| No. of frames which were Transmitted from this IP interface. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceTxQueueBufs | 1.3.6.1.4.1.164.8.13.2.1.14 | ||
| No. of buffers which are waiting in the Trasnsmit Queue. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceTxDiscarded | 1.3.6.1.4.1.164.8.13.2.1.15 | ||
| No. of frames which were ready to be transmitted but were Discarded. The PS will discard frames if the transmit queue is too long. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceRipRxFrames | 1.3.6.1.4.1.164.8.13.2.1.16 | ||
| No. of RIP frames which were received on this IP interface. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceRipTxFrames | 1.3.6.1.4.1.164.8.13.2.1.17 | ||
| No. of RIP Frames which were transmitted from this IP interface. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIpInterfaceRipWaitingMsgs | 1.3.6.1.4.1.164.8.13.2.1.18 | ||
| No. of RIP messages which are waiting to be transmitted to the Network. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIsdn | 1.3.6.1.4.1.164.8.14 | ||
| OBJECT IDENTIFIER | |||
| pktSwchIsdnGlobal | 1.3.6.1.4.1.164.8.14.1 | ||
| OBJECT IDENTIFIER | |||
| pktSwchIsdnGlobalCallRetries | 1.3.6.1.4.1.164.8.14.1.1 | ||
| Number of times the call request is repeated after failure. Possible values: 0 - Disable retry mechanism 1-255 - Number of retries default value: 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchIsdnGlobalCallRetryDelay | 1.3.6.1.4.1.164.8.14.1.2 | ||
| Time interval between retries (in seconds). Possible values: 5 - 250 Default value: 15 | |||
| OBJECT-TYPE | |||
| Integer32 | 5..250 | ||
| pktSwchIsdnGlobalCallinactivity | 1.3.6.1.4.1.164.8.14.1.3 | ||
| Time of inactivity in seconds, after which the call will be disconnected. An x.25 link is considered inactive when there are no open calls on the link. A frame relay link is considered inactive when there is no traffic on the link. Possible values: 0 - No disconnection on inactivity. 1 - 65000 - Time period (in seconds). Default value: 180 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..65000 | ||
| pktSwchIsdnGlobalStatus | 1.3.6.1.4.1.164.8.14.1.4 | ||
| The status of the Isdn Global parameters. Used for saving the Isdn global parameters. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), underCreation(3) | ||
| pktSwchIsdnRoutTable | 1.3.6.1.4.1.164.8.14.2 | ||
| The Isdn Routing Table entries in the Packet Switch. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIsdnRoutEntry | |||
| pktSwchIsdnRoutEntry | 1.3.6.1.4.1.164.8.14.2.1 | ||
| Isdn Routing Entry defines the contents of each entry in the table. The outgoing addresses are in a different table - pktSwchIsdnRoutAddrTable. The row status in this table will be used for both tables. | |||
| OBJECT-TYPE | |||
| PktSwchIsdnRoutEntry | |||
| pktSwchIsdnRoutId | 1.3.6.1.4.1.164.8.14.2.1.1 | ||
| Number of this routing entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIsdnRoutDataBandWidth | 1.3.6.1.4.1.164.8.14.2.1.2 | ||
| Isdn Bandwidth which will be used for the data routed via this entry. The ISDN interface will be configured with the speed which is selected. Possible values: 2 - 56 Kbps. 3 - 64 Kbps. Default value: 3 | |||
| OBJECT-TYPE | |||
| INTEGER | bw56Kbps(2), bw64Kbps(3) | ||
| pktSwchIsdnRoutOptions | 1.3.6.1.4.1.164.8.14.2.1.3 | ||
| Special Options for this routing entry. Possible values: 1 - No special options. 2 - Return to main link. This option is used when the current link is defined as a backup link and the main link becomes active. Default value: 1 | |||
| OBJECT-TYPE | |||
| INTEGER | noOptions(1), returnToMainLink(2) | ||
| pktSwchIsdnRoutStatus | 1.3.6.1.4.1.164.8.14.2.1.4 | ||
| The status of this routing table entry + address table (pktSwchIsdnOutAddrTable). For creating a new entry select createRequest. A new route entry will be created together with an out address entry. There may be more than 1 addresses. For example, if there is 1 outgoing address and 2 alternatives, the new address entry will have 3 indices. For deleting an entry select invalid. The relevant address entry should be deleted too. For saving an entry select valid. Save should include the addresses of the current entry in the pktSwchIsdnOutAddrTable | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIsdnOutAddrTable | 1.3.6.1.4.1.164.8.14.3 | ||
| Outgoing ISDN addresses used by the ISDN routing table. The address table contains outgoing addresses and alternative addresses in case the connection to the first addresses does not succeed. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIsdnOutAddrEntry | |||
| pktSwchIsdnOutAddrEntry | 1.3.6.1.4.1.164.8.14.3.1 | ||
| Isdn Outgoing Address Entry defines the contents of each entry in the outgoing address table. Each entry has 2 indices: 1. RoutId is the ID in the routing table. 2. AddrId is the ID containing the Outgoing address and sub address. | |||
| OBJECT-TYPE | |||
| PktSwchIsdnOutAddrEntry | |||
| pktSwchIsdnOutAddrRoutId | 1.3.6.1.4.1.164.8.14.3.1.1 | ||
| ID in the ISDN routing table. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIsdnOutAddrId | 1.3.6.1.4.1.164.8.14.3.1.2 | ||
| Number of the address + subaddress pair for each routing ID. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..3 | ||
| pktSwchIsdnOutAddr | 1.3.6.1.4.1.164.8.14.3.1.3 | ||
| Destination ISDN Outgoing (Remote) address. The data will be routed out to this address. Possible values: Up to 17 decimal digits. Default value: string of length 0. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..17) | ||
| pktSwchIsdnOutSubAddr | 1.3.6.1.4.1.164.8.14.3.1.4 | ||
| Destination ISDN Outgoing (Remote) sub address. The data will be routed out to the out addrress with this sub address. Possible values: Up to 6 decimal digits. Default value: string of length 0. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| pktSwchIsdnAcceptTable | 1.3.6.1.4.1.164.8.14.4 | ||
| Table of Isdn addresses which will be accepted by the agent. If there is a dial back (answer) address, the incoming call will be disconnected and dial back will initiate. Most of the accept list parameters are in RFC2128 in the dialCtlPeerCfgTable. The parameters which are not in the the standard RFC2128 and are required, are defined here in the private PS MIB. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIsdnAcceptEntry | |||
| pktSwchIsdnAcceptEntry | 1.3.6.1.4.1.164.8.14.4.1 | ||
| Isdn Accept Entry defines the contents of each entry in the table. | |||
| OBJECT-TYPE | |||
| PktSwchIsdnAcceptEntry | |||
| pktSwchIsdnAcceptId | 1.3.6.1.4.1.164.8.14.4.1.1 | ||
| Identifier of Accept table entry. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchIsdnAcceptSecondaryLink | 1.3.6.1.4.1.164.8.14.4.1.2 | ||
| A valid Isdn link number on which the call will be accepted when the Primary link (RFC2128.dialCtlPeerCfgLowerIf)is unavailable. Possible values: 255 - No Secondary link. or The complementary to the primary ISDN link number. Complementary links are: [1;2] and [7;8]. If Primary Link Number is set to first available <0>, the Secondary link must be set to No Secondary link <255>. Default value is complementary to the primary link no. defined in rfc2128.dialCtlPeerCfgLowerIf. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| pktSwchIsdnAcceptDialbkSubAddress | 1.3.6.1.4.1.164.8.14.4.1.3 | ||
| Isdn sub address which will be used by the agent for dialing back. Possible values: Up to 6 decimal digits. Default value: string of length 0. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| pktSwchIsdnAcceptStatus | 1.3.6.1.4.1.164.8.14.4.1.4 | ||
| The status of this accept table entry. For creating a new entry select createRequest, For deleting an entry select invalid. For saving an entry select valid. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchIsdnLinkTable | 1.3.6.1.4.1.164.8.14.5 | ||
| Table of Isdn Link parameters. Most of the link parameters are in in RFC2127. Isdn Call statistics are RFC2128. The parameters which are not in the the standard RFCs , and are required, are defined here in the private PS MIB. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchIsdnLinkEntry | |||
| pktSwchIsdnLinkEntry | 1.3.6.1.4.1.164.8.14.5.1 | ||
| Isdn Link Entry defines the contents of each entry in the table. | |||
| OBJECT-TYPE | |||
| PktSwchIsdnLinkEntry | |||
| pktSwchIsdnLinkBchannel | 1.3.6.1.4.1.164.8.14.5.1.1 | ||
| Defines which B channels are used for Leased Lines Only. Default value: noBchannel(1). | |||
| OBJECT-TYPE | |||
| INTEGER | noBchannel(1), b1(2), b2(3), b1Andb2(4) | ||
| pktSwchIsdnCallsClrs | 1.3.6.1.4.1.164.8.14.5.1.2 | ||
| Number of calls on this link which were cleared since the link was activated. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| pktSwchIsdnTestCmd | 1.3.6.1.4.1.164.8.14.5.1.3 | ||
| Activate/Stop an ISDN test on the current ISDN link. In order to Activate the test, set the TestCmd to 3 (activate). For stopping the test, set the TestCmd to 2 (noOp). Important: In order for the test to succeed, the user must set the pktSwchIsdnTestAddr and Subaddr to their required values before activating the test. | |||
| OBJECT-TYPE | |||
| INTEGER | noOp(2), activate(3) | ||
| pktSwchIsdnTestAddr | 1.3.6.1.4.1.164.8.14.5.1.4 | ||
| Destination ISDN Outgoing (Remote) address which will be called in order to test the ISDN. Possible values: Up to 17 decimal digits. Default value: string of length 0. Important: In order for the test to succeed, the user must also set the pktSwchIsdnTestSubAddr to the required values before activating the test. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..17) | ||
| pktSwchIsdnTestSubAddr | 1.3.6.1.4.1.164.8.14.5.1.5 | ||
| Destination ISDN Outgoing (Remote) address which will be called in order to test the ISDN. Possible values: Up to 6 decimal digits. Default value: string of length 0. Important: In order for the test to succeed, the user must also set the pktSwchIsdnTestAddr to the required values before activating the test. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..6) | ||
| pktSwchPpp | 1.3.6.1.4.1.164.8.15 | ||
| OBJECT IDENTIFIER | |||
| pktSwchPppSecretsTable | 1.3.6.1.4.1.164.8.15.1 | ||
| Table of PPP Secret parameters. The parameters are defined in rfc1472 except for the ROW status which is defined here. In the standard, there is no create request option, so in order to be consistent with other ROW statuses in the Packet Switches it is defined here. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPppSecretsEntry | |||
| pktSwchPppSecretsEntry | 1.3.6.1.4.1.164.8.15.1.1 | ||
| PPP Secrets Entry defines the contents of each entry in the table. | |||
| OBJECT-TYPE | |||
| PktSwchPppSecretsEntry | |||
| pktSwchPppSecretsPairId | 1.3.6.1.4.1.164.8.15.1.1.1 | ||
| Index of the Secrets Pair. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..200 | ||
| pktSwchPppSecretsStatus | 1.3.6.1.4.1.164.8.15.1.1.2 | ||
| The status of the PPP Secrets table. For creating a new entry select createRequest, For deleting an entry select invalid. For saving an entry select valid. | |||
| OBJECT-TYPE | |||
| INTEGER | valid(1), createRequest(2), underCreation(3), invalid(4) | ||
| pktSwchPppChanTable | 1.3.6.1.4.1.164.8.15.2 | ||
| Table of PPP Channel parameters. The table can be used for Async as well as Sync parameters. In case a parameter is irrelevant for Async or Sync a value may be returned. Statistics Parameters are already defined in rfc1213: ifInUcastPkts, ifOutUcastPkts, ifInErrors, ifOutErrors | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PktSwchPppChanEntry | |||
| pktSwchPppChanEntry | 1.3.6.1.4.1.164.8.15.2.1 | ||
| PPP Channel Entry defines the contents of each entry in the table. | |||
| OBJECT-TYPE | |||
| PktSwchPppChanEntry | |||
| pktSwchPppChanSpeed | 1.3.6.1.4.1.164.8.15.2.1.1 | ||
| The port's speed in bits per second. For Async channels: Default value: 14 . For Sync Links: Use not_applicable(255) The Sync Links have an internal clock with different values. | |||
| OBJECT-TYPE | |||
| INTEGER | s110bps(1), s300bps(2), s1200bps(3), s600bps(4), s75bps(5), s150bps(6), s2400bps(12), s4800bps(13), s9600bps(14), s19200bps(15), s38400bps(19), s57600bps(20), s115200bps(21), notApplicable(255) | ||
| pktSwchPppChanFlowCtlDuration | 1.3.6.1.4.1.164.8.15.2.1.2 | ||
| Hardware Flow Control Duration. 1..254 - Duration (in 50ms intervals). when timer expires, flow control stops. 0 - No Hardware flow control. 255 - Continuous Flow Control. Default value: 0. For Sync Links, return 0. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchPppChanStopBits | 1.3.6.1.4.1.164.8.15.2.1.3 | ||
| This entry indicates the number of stop bits per character. The options are either (1) one stop bit, (2) two stop bits, or (3) 1.5 stop bits. For Sync Links: notApplicable(255). | |||
| OBJECT-TYPE | |||
| INTEGER | one(1), two(2), oneAndHalf(3), notApplicable(255) | ||
| pktSwchPppChanBitPerChar | 1.3.6.1.4.1.164.8.15.2.1.4 | ||
| The number of data bits per character supported by the ppp link. Legal values for Async channels: 5..8 . For Sync Links: 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..8 | ||
| pktSwchPppChanParity | 1.3.6.1.4.1.164.8.15.2.1.5 | ||
| This entry selects the type of parity to be checked or generated. The options are (1) space parity, (2) mark parity, (3) even parity, (4) odd parity, or (255) no parity. For Sync Links: none(255). | |||
| OBJECT-TYPE | |||
| INTEGER | space(1), mark(2), even(3), odd(4), none(255) | ||
| pktSwchPppChanNegotiationTrigger | 1.3.6.1.4.1.164.8.15.2.1.6 | ||
| The trigger which is used in order to start the Negotiation. The HW signals which are used are: DCD (Data Carrier Detect) - issued by DCE DSR (Data Set Ready) - issued by DCE DTR (Data Terminal Ready) - issued by DTE 1 - Start negotiation on signal assertion. The Peer will issue a DCD/DSR Signal if it is DCE or DTR if it is DTE. If the current channel/link is DCE, it will check the DTR. If the current channel/link is DTE, it will check the DCD/DSR. When the HW signal is issued, negotiation will begin. 2 - Data Triggered. The current channel/link will issue a HW signal. Negotiation will begin when data is received. 3 - Combination of option 1 and option 2. 255 - Starts negotiation after reset. Ignore HW signals. Default Value for Async Channel: 255. Default Value for Sync Link: 3 | |||
| OBJECT-TYPE | |||
| INTEGER | hw-signal(1), data-triggered(2), hw-signal-or-data(3), after-reset(255) | ||
| pktSwchPppChanMRU | 1.3.6.1.4.1.164.8.15.2.1.7 | ||
| Maximum Receive Unit. Size of the packet which is negotiated with the connected device. Default value: 1500 . | |||
| OBJECT-TYPE | |||
| Integer32 | 1500..4096 | ||
| pktSwchPppChanACCM | 1.3.6.1.4.1.164.8.15.2.1.8 | ||
| Async Control Character Map - The ACCM value serves as a mask for the first 32 characters in the ASCII table. Control characters may cause problems when they are transferred on the network. This can be handled by escaping them ( adding escape character to them ). For example , when using modems in the network which can not receive X-on and X-off characters. The ACCM is a mask which shows which control characters will be handled with an escape sequence. Each bit represents one character. Possible values: Octet string of 4 bytes: 00000000 . A bit with value 1 will cause the character to be in an escape sequence. 0 will leave the character as it is. Example : to use XON and XOFF as escape sequence : 000A0000 Default value: 00000000. For Sync Links return the default. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| pktSwchPppChanAuthentication | 1.3.6.1.4.1.164.8.15.2.1.9 | ||
| Port Authentication Type. 1 - No Authentication: User side Only. 2 - Configuration of the Host side. PAP (Password Authentication Protocol) or CHAP (Challenge Handshake Authentication Protocol) will be accepted by the current host. 3 - Configuration of the host side as CHAP only. Only CHAP will be accepted by the current host. Default value: 1 . | |||
| OBJECT-TYPE | |||
| INTEGER | no-authentication(1), pap-or-chap(2), chap-only(3) | ||
| pktSwchPppChanInternalClock | 1.3.6.1.4.1.164.8.15.2.1.10 | ||
| The internal clock rate of the MLPPP Link. Default value: 9. For Async channels: return 255. | |||
| OBJECT-TYPE | |||
| INTEGER | r3000bps(1), r4800bps(2), r9600bps(3), r14400bps(4), r19200bps(5), r38400bps(6), r48Kbps(7), r56Kbps(8), r64Kbps(9), r128Kbps(10), r256Kbps(11), r384Kbps(12), r512Kbps(13), r768Kbps(14), r1024Kbps(15), r1445Kbps(16), r2048Kbps(17), external(255) | ||
| pktSwchPppChanBundle | 1.3.6.1.4.1.164.8.15.2.1.11 | ||
| Bundle Number. It is possible to attach a few channels/links to a bundle. If the User enters a non existing bundle number, the PS will create a new bundle with this number. The bundle number may be: 1..255 If the bundle number is 0 it means: do not attach to bundle. Default value: 0 . | |||
| OBJECT-TYPE | |||
| Integer32 | 0..255 | ||
| pktSwchpPppChanIsdnRoutId | 1.3.6.1.4.1.164.8.15.2.1.12 | ||
| ISDN destination. ID (1..200) in the ISDN routing table containing the outgoing ISDN address for this channel/link. For no destination: 0 Default value: 0 | |||
| OBJECT-TYPE | |||
| Integer32 | 0..200 | ||
| pktSwchpPppChanLastEvent | 1.3.6.1.4.1.164.8.15.2.1.13 | ||
| Status showing the last PPP event which occured on the line described in an ascii string. Examples: 1. Received Configuration Request. 2. Sent Protocol Reject. 3. Error: Can Not Compress Frame. Default: 0 for no last event on this link or channel. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..80) | ||
| radEthRptr | 1.3.6.1.4.1.164.9 | ||
| OBJECT IDENTIFIER | |||
| radEthRptrEvents | 1.3.6.1.4.1.164.9.0 | ||
| The events for Ethernet Repeater. | |||
| OBJECT-IDENTITY | |||
| etRptrHealth | 1.3.6.1.4.1.164.9.0.1 | ||
| The etRptrHealth trap conveys information related to the operational status of the repeater. This trap is sent either when the value of etRptrOperStatus changes, or upon completion of a non-disruptive test. See the etRptrOperStatus object for descriptions of the information that is sent. The agent must throttle the generation of consecutive etRptrHealth traps so that there is at least a five-second gap between traps of this type. When traps are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a trap means sending to all configured recipients.) | |||
| NOTIFICATION-TYPE | |||
| etRptrOperStatus | |||
| rptrGroupOperStatus | |||
| agnLed | |||
| etRptrResetEvent | 1.3.6.1.4.1.164.9.0.2 | ||
| The etRptrResetEvent trap conveys information related to the operational status of the repeater. This trap is sent on completion of a repeater reset action. A repeater reset action is defined as an a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std], when triggered by a management command (e.g., an SNMP Set on the etRptrReset object). The agent must throttle the generation of consecutive etRptrResetEvent traps so that there is at least a five-second gap between traps of this type. When traps are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a trap means sending to all configured recipients.) The etRptrResetEvent trap is not sent when the agent restarts and sends an SNMP coldStart or warmStart trap. However, it is recommended that a repeater agent send the etRptrOperStatus object as an optional object with its coldStart and warmStart trap PDUs. The etRptrOperStatus object must be included in the varbind list sent with this trap. The agent may optionally include the etRptrHealthText object as well. | |||
| NOTIFICATION-TYPE | |||
| etRptrOperStatus | |||
| etRptrIndex | |||
| agnLed | |||
| etRptrConfig | 1.3.6.1.4.1.164.9.0.3 | ||
| This trap is sent upon every change of the etRptrMdlVector object. | |||
| NOTIFICATION-TYPE | |||
| etRptrMdlVector | |||
| agnLed | |||
| etRptrTable | 1.3.6.1.4.1.164.9.1 | ||
| This table contains repeater data specific to the etRptrIndex. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EtRptrEntry | |||
| etRptrEntry | 1.3.6.1.4.1.164.9.1.1 | ||
| An entry in table etRptrTable. | |||
| OBJECT-TYPE | |||
| EtRptrEntry | |||
| etRptrIndex | 1.3.6.1.4.1.164.9.1.1.1 | ||
| The Repeater Id, this table data refer to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| etRptrGroupCapacity | 1.3.6.1.4.1.164.9.1.1.2 | ||
| The etRptrGroupCapacity is the number of groups that can be contained within the repeater. Within each managed repeater, the groups are uniquely numbered in the range from 1 to etRptrGroupCapacity. Some groups may not be present in the repeater, in which case the actual number of groups present will be less than etRptrGroupCapacity. The number of groups present will never be greater than etRptrGroupCapacity. Note: In practice, this will generally be the number of field-replaceable units (i.e., modules, cards, or boards) that can fit in the physical repeater enclosure, and the group numbers will correspond to numbers marked on the physical enclosure. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..1024 | ||
| etRptrOperStatus | 1.3.6.1.4.1.164.9.1.1.3 | ||
| The etRptrOperStatus object indicates the operational state of the repeater. The etRptrHealthText object may be consulted for more specific information about the state of the repeater's health. In the case of multiple kinds of failures (e.g., repeater failure and port failure), the value of this attribute shall reflect the highest priority failure in the following order, listed highest priority first: rptrFailure(3) groupFailure(4) portFailure(5) generalFailure(6). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), ok(2), rptrFailure(3), groupFailure(4), portFailure(5), generalFailure(6) | ||
| etRptrHealthText | 1.3.6.1.4.1.164.9.1.1.4 | ||
| The health text object is a text string that provides information relevant to the operational state of the repeater. Agents may use this string to provide detailed information on current failures, including how they were detected, and/or instructions for problem resolution. The contents are agent-specific. | |||
| OBJECT-TYPE | |||
| DisplayString | SIZE(0..255) | ||
| etRptrReset | 1.3.6.1.4.1.164.9.1.1.5 | ||
| Setting this object to reset(2) causes a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std]. Setting this object to noReset(1) has no effect. The agent will always return the value noReset(1) when this object is read. After receiving a request to set this variable to resetHW(2), the agent is allowed to delay the reset for a short period. For example, the implementor may choose to delay the reset long enough to allow the SNMP response to be transmitted. In any event, the SNMP response must be transmitted. This action does not reset the management counters defined in this document nor does it affect the portAdminStatus parameters. Included in this action is the execution of a disruptive Self-Test with the following characteristics: a) The nature of the tests is not specified. b) The test resets the repeater but without affecting management information about the repeater. c) The test does not inject packets onto any segment. d) Packets received during the test may or may not be transferred. e) The test does not interfere with management functions. After performing this self-test, the agent will update the repeater health information (including etRptrOperStatus and etRptrHealthText), and send a etRptrHealth trap. Setting this object to resetConfig(3) will cause resetting the repeater to its default values. | |||
| OBJECT-TYPE | |||
| INTEGER | noReset(1), resetHW(2), resetConfig(3) | ||
| etRptrNonDisruptTest | 1.3.6.1.4.1.164.9.1.1.6 | ||
| Setting this object to selfTest(2) causes the repeater to perform a agent-specific, non- disruptive self-test that has the following characteristics: a) The nature of the tests is not specified. b) The test does not change the state of the repeater or management information about the repeater. c) The test does not inject packets onto any segment. d) The test does not prevent the relay of any packets. e) The test does not interfere with management functions. After performing this test, the agent will update the repeater health information (including etRptrOperStatus and etRptrHealthText) and send a etRptrHealth trap. Note that this definition allows returning an 'okay' result after doing a trivial test. Setting this object to noSelfTest(1) has no effect. The agent will always return the value noSelfTest(1) when this object is read. | |||
| OBJECT-TYPE | |||
| INTEGER | noSelfTest(1), selfTest(2) | ||
| etRptrTotalPartitionedPorts | 1.3.6.1.4.1.164.9.1.1.7 | ||
| This object returns the total number of ports in the repeater whose current state meets all three of the following criteria: etRptrPortOperStatus does not have the value notPresent(3), etRptrPortAdminStatus is enabled(1), and etRptrPortAutoPartitionState is autoPartitioned(2). | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| etRptrMdlVector | 1.3.6.1.4.1.164.9.1.1.8 | ||
| This object returns a vector mapping the location of the repeater modules to their corresponding bit position. A bit that is set indicates an existing module | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| etRptrMonitorTransmitCollisions | 1.3.6.1.4.1.164.9.1.1.9 | ||
| This counter is incremented every time the repeater state machine enters the TRANSMIT COLLISION state from any state other than ONE PORT LEFT (Ref: Fig 9-2, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 16 hours. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| etRptrSecTable | 1.3.6.1.4.1.164.9.2 | ||
| Repeater Security Table | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| EtRptrSecEntry | |||
| etRptrSecEntry | 1.3.6.1.4.1.164.9.2.1 | ||
| An entry in table etRptrSecTable. | |||
| OBJECT-TYPE | |||
| EtRptrSecEntry | |||
| etRptrId | 1.3.6.1.4.1.164.9.2.1.1 | ||
| The Repeater Id, this table data refer to. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| etRptrSecID | 1.3.6.1.4.1.164.9.2.1.2 | ||
| Segment's security unique identification number | |||
| OBJECT-TYPE | |||
| Integer32 | 1..3 | ||
| etRptrSecEnable | 1.3.6.1.4.1.164.9.2.1.3 | ||
| This entry indicates whether the specific segment's security is active or not | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| etRptrSecPattern | 1.3.6.1.4.1.164.9.2.1.4 | ||
| A six-octet(48 bit) pattern: where the masked bits of etRptrSecMask need to match the MAC address of each port within the segment.Value of all zeros indicates no security. | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| etRptrSecMask | 1.3.6.1.4.1.164.9.2.1.5 | ||
| Mask of the allowed MAC address that can be connected through the ports within the segment | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| radRouter | 1.3.6.1.4.1.164.11 | ||
| OBJECT IDENTIFIER | |||
| rtrBridge | 1.3.6.1.4.1.164.11.7 | ||
| OBJECT IDENTIFIER | |||
| radAtm | 1.3.6.1.4.1.164.12 | ||
| OBJECT IDENTIFIER | |||
| atmNte | 1.3.6.1.4.1.164.12.3 | ||
| OBJECT IDENTIFIER | |||
| atmNteEvents | 1.3.6.1.4.1.164.12.3.0 | ||
| The events for RAD ATM products. | |||
| OBJECT-IDENTITY | |||
| atmNtePrt | 1.3.6.1.4.1.164.12.3.2 | ||
| OBJECT IDENTIFIER | |||
| atmNtePrtConfig | 1.3.6.1.4.1.164.12.3.2.1 | ||
| OBJECT IDENTIFIER | |||
| atmNteConfIfTable | 1.3.6.1.4.1.164.12.3.2.1.1 | ||
| The Physical interface configuration table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmNteConfIfEntry | |||
| atmNteConfIfEntry | 1.3.6.1.4.1.164.12.3.2.1.1.1 | ||
| An entry in the Physical interface configuration table. The ifIndex is of the lowest physical layer. | |||
| OBJECT-TYPE | |||
| AtmNteConfIfEntry | |||
| atmConfIfTransmitClk | 1.3.6.1.4.1.164.12.3.2.1.1.1.1 | ||
| The transmit clock of the port. | |||
| OBJECT-TYPE | |||
| INTEGER | internal(2), external(3), loopback(4), adaptive(5) | ||
| atmConfIfLoopback | 1.3.6.1.4.1.164.12.3.2.1.1.1.2 | ||
| Interface Loopback. | |||
| OBJECT-TYPE | |||
| INTEGER | internal(2), external(3), disable(4) | ||
| atmConfIfFrameType | 1.3.6.1.4.1.164.12.3.2.1.1.1.3 | ||
| The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12). Valid values for Ethernet interface: ethCrcTrans (8), ethCrcNotTrans(9). (DS1 interfaces frame type is specified in the DSX1 mib). | |||
| OBJECT-TYPE | |||
| INTEGER | other(1), sonet(2), sdh(3), direct(4), plcpInternal(5), plcpExternal(6), e3(7), ethCrcTrans(8), ethCrcNotTrans(9), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbling(12) | ||
| atmConfIfCardType | 1.3.6.1.4.1.164.12.3.2.1.1.1.4 | ||
| The card type. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), sc13m-155(2), st13s-155(3), st13l-155(4), utp-155(5), cx-bnc-155(6), e3(7), t3(8), e1(9), e1-ltu(10), fc13l-155(11), fc13lh-155(12), fc15lh-155(13), fc13l-e3(14), fc13lh-e3(15), fc15lh-e3(16), fc13l-t3(17), fc13lh-t3(18), fc15lh-t3(19) | ||
| atmConfAtmIfVpiVciLimit | 1.3.6.1.4.1.164.12.3.2.1.1.1.5 | ||
| The limit on the sum of the VPI+VCI bits for this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | bits15(2), bits17(3) | ||
| atmConfIfHwFeatures | 1.3.6.1.4.1.164.12.3.2.1.1.1.6 | ||
| HW features command. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(1), enable(2) | ||
| atmConfIfOutputRate | 1.3.6.1.4.1.164.12.3.2.1.1.1.7 | ||
| This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmConfIfInputRate | 1.3.6.1.4.1.164.12.3.2.1.1.1.8 | ||
| This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmConfAlarmForwarding | 1.3.6.1.4.1.164.12.3.2.1.1.1.9 | ||
| Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a failure on this port. enable(3) - will forward an alarm upon a failure on this port. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| atmNteAlarmIfTable | 1.3.6.1.4.1.164.12.3.2.1.2 | ||
| The interface Alarm table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmNteAlarmIfEntry | |||
| atmNteAlarmIfEntry | 1.3.6.1.4.1.164.12.3.2.1.2.1 | ||
| An entry in the interface Alarm table. | |||
| OBJECT-TYPE | |||
| AtmNteAlarmIfEntry | |||
| atmInterfaceActiveAlarms | 1.3.6.1.4.1.164.12.3.2.1.2.1.1 | ||
| A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Line AIS (SONET)/ PLCP LOF (DS3) 4 - LOP 5 - Path AIS 6 - SLM 7 - LCD 8 - Line RDI (SONET)/ PLCP Yellow (DS3) 9 - Path RDI (SONET)/ RDI (DS3) 10 - Section BIP (SONET)/ P1/P2 (DS3) > Threshold 11 - Line BIP (SONET)/ PLCP BIP (DS3) > Threshold 12 - Line FEBE (SONET)/ PLCP FEBE (DS3) > Threshold 13 - Path BIP > Threshold 14 - Path FEBE > Threshold 15 - HW Failure | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdSectionBIP | 1.3.6.1.4.1.164.12.3.2.1.2.1.2 | ||
| When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdLineBIP | 1.3.6.1.4.1.164.12.3.2.1.2.1.3 | ||
| When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdLineFEBE | 1.3.6.1.4.1.164.12.3.2.1.2.1.4 | ||
| When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdPathBIP | 1.3.6.1.4.1.164.12.3.2.1.2.1.5 | ||
| When Path BIPs are greater than this threshold, an active alarm is raised. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdPathFEBE | 1.3.6.1.4.1.164.12.3.2.1.2.1.6 | ||
| When Path FEBEs are greater than this threshold, an active alarm is raised. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdErroredCells | 1.3.6.1.4.1.164.12.3.2.1.2.1.7 | ||
| When Errored Cells are greater than this threshold, an active alarm is raised. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdLostCells | 1.3.6.1.4.1.164.12.3.2.1.2.1.8 | ||
| When Lost Cells are greater than this threshold, an active alarm is raised. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmThresholdMisinsertedCells | 1.3.6.1.4.1.164.12.3.2.1.2.1.9 | ||
| When Misinserted Cells are greater than this threshold, an active alarm is raised. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmInterfaceAlarmStatus | 1.3.6.1.4.1.164.12.3.2.1.2.1.10 | ||
| The variable is on(3) when there is any active alarm on this interface. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| atmInterfaceMaskAlarms | 1.3.6.1.4.1.164.12.3.2.1.2.1.11 | ||
| A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmNteConfVpTable | 1.3.6.1.4.1.164.12.3.2.1.3 | ||
| The ATM VP configuration table. The table is an extension to the atmVplTable of RFC-1695. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmNteConfVpEntry | |||
| atmNteConfVpEntry | 1.3.6.1.4.1.164.12.3.2.1.3.1 | ||
| An entry in the ATM VP configuration table. ifIndex of the ATM layer. | |||
| OBJECT-TYPE | |||
| AtmNteConfVpEntry | |||
| atmConfVpPolicing | 1.3.6.1.4.1.164.12.3.2.1.3.1.1 | ||
| Policing method desired for this VPL. | |||
| OBJECT-TYPE | |||
| INTEGER | none(1), police(2), monitor(3), shaping(4), policingAndShaping(5) | ||
| atmConfVpCCAdminStatus | 1.3.6.1.4.1.164.12.3.2.1.3.1.2 | ||
| up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of remote agent ( start receiving Oam cells from remote side ). listenToActivationCells (6) - Passive listener till gets an activation request originateActivationCells(7) - Sands Activation cell according to atmConfVcCCDirection. | |||
| OBJECT-TYPE | |||
| INTEGER | up(2), down(3), source(4), sink(5), listenToActivationCells(6), originateActivationCells(7) | ||
| atmConfVpLoopbackAdminStatus | 1.3.6.1.4.1.164.12.3.2.1.3.1.3 | ||
| up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. llid(4) - Transmitting LB cells with llid indicated in the address field. segment(5) - Transmitting Segment LB cells with llid all ones. endToEnd(6) - Transmitting End to End LB cells with llid all ones. segmentLlid(7) - Transmitting Segment LB cells with llid indicated in the address field. endToEndLlid(8) - Transmitting LB cells with llid indicated in the address field. This parameter value might be in conflict with atmConfVpOamSupport value, since this parameter is for LB, while atmConfVpOamSupport is for any other OAM cells. | |||
| OBJECT-TYPE | |||
| INTEGER | up(2), down(3), llid(4), segment(5), endToEnd(6), segmentLlid(7), endToEndLlid(8) | ||
| atmConfVpLoopbackSinkAddress | 1.3.6.1.4.1.164.12.3.2.1.3.1.4 | ||
| Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(0..20) | ||
| atmConfVpCongestionControl | 1.3.6.1.4.1.164.12.3.2.1.3.1.5 | ||
| Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI | |||
| OBJECT-TYPE | |||
| OCTET STRING | |||
| atmConfVpCCDirection | 1.3.6.1.4.1.164.12.3.2.1.3.1.6 | ||
| both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells. | |||
| OBJECT-TYPE | |||
| INTEGER | both(2), source(4), sink(5) | ||
| atmConfVpCreationTime | 1.3.6.1.4.1.164.12.3.2.1.3.1.7 | ||
| A date-time in which the VP was created. | |||
| OBJECT-TYPE | |||
| DateAndTime | |||
| atmConfVpOamSupport | 1.3.6.1.4.1.164.12.3.2.1.3.1.8 | ||
| OAM support mode, which determines the device location in a segment wise. | |||
| OBJECT-TYPE | |||
| INTEGER | intermediate(1), segmentTermination(2), endToEndTermination(3) | ||
| atmConfVpCCOperStatus | 1.3.6.1.4.1.164.12.3.2.1.3.1.9 | ||
| initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeout occured on receiving answer from the remote agent. denied (10) - CC activation process rejected by remote agent. conflict (11) - local and remote sides requested activation simultaneously. manual (12) - OAM CC of local agent activated manually. | |||
| OBJECT-TYPE | |||
| INTEGER | initial(1), source(4), sink(5), both(8), timeout(9), denied(10), conflict(11), manual(12) | ||
| atmConfVpLoopbackTraffic | 1.3.6.1.4.1.164.12.3.2.1.3.1.10 | ||
| This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting this value means that the loop is currently running. | |||
| OBJECT-TYPE | |||
| INTEGER | off(2), on(3) | ||
| atmConfVpLoopbackFailureInd | 1.3.6.1.4.1.164.12.3.2.1.3.1.11 | ||
| This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of a segment RDI. segmentAisAndRdi(5) - will cause Tx of a segment AIS & RDI. endToEndAis(6) - will cause Tx of an End to End AIS. endToEndRdi(7) - will cause Tx of an End to End RDI. endToEndAisAndRdi(8) - will cause Tx of an End to End AIS & RDI. Default: disabled(2). | |||
| OBJECT-TYPE | |||
| INTEGER | disabled(2), segmentAis(3), segmentRdi(4), segmentAisAndRdi(5), endToEndAis(6), endToEndRdi(7), endToEndAisAndRdi(8) | ||
| atmConfVpLoopbackFailureThreshold | 1.3.6.1.4.1.164.12.3.2.1.3.1.12 | ||
| The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmConfVpOamDirection | 1.3.6.1.4.1.164.12.3.2.1.3.1.13 | ||
| The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), downStream(2), upStream(3) | ||
| atmNteAlarmVpTable | 1.3.6.1.4.1.164.12.3.2.1.5 | ||
| The ATM VP Alarm table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmNteAlarmVpEntry | |||
| atmNteAlarmVpEntry | 1.3.6.1.4.1.164.12.3.2.1.5.1 | ||
| An entry in the ATM VP Alarm table. ifIndex of the ATM layer. | |||
| OBJECT-TYPE | |||
| AtmNteAlarmVpEntry | |||
| atmNteVpAlarmVpi | 1.3.6.1.4.1.164.12.3.2.1.5.1.1 | ||
| The VPI on which there is an active alarm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmNteVpActiveAlarms | 1.3.6.1.4.1.164.12.3.2.1.5.1.2 | ||
| A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Continuity 3 - VP RDI Reception 4 - VP Errored Cells > Threshold 5 - VP Lost Cells > Threshold 6 - VP Misinserted Cells > Threshold | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmNteAlarmVcTable | 1.3.6.1.4.1.164.12.3.2.1.6 | ||
| The ATM VC Alarm table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmNteAlarmVcEntry | |||
| atmNteAlarmVcEntry | 1.3.6.1.4.1.164.12.3.2.1.6.1 | ||
| An entry in the ATM VC Alarm table. ifIndex of the ATM layer. | |||
| OBJECT-TYPE | |||
| AtmNteAlarmVcEntry | |||
| atmNteVcAlarmVpi | 1.3.6.1.4.1.164.12.3.2.1.6.1.1 | ||
| The VPI of the VC on which there is an active alarm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmNteVcAlarmVci | 1.3.6.1.4.1.164.12.3.2.1.6.1.2 | ||
| The VCI of the VC on which there is an active alarm. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmNteVcActiveAlarms | 1.3.6.1.4.1.164.12.3.2.1.6.1.3 | ||
| A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Continuity 3 - VC RDI 4 - VC Errored Cells > Threshold 5 - VC Lost Cells > Threshold 6 - VC Misinserted Cells > Threshold 7 - Tx VC AIS 8 - Tx VC RDI | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radExperimental | 1.3.6.1.4.1.164.20 | ||
| OBJECT IDENTIFIER | |||
| MacAddress | |||
| OCTET STRING | SIZE(6) | ||
| TimeSlots | |||
| OCTET STRING | SIZE(4) | ||
| MngEntry | |||
| SEQUENCE | |||
| Integer32 as mngID | |||
| IpAddress as mngIP | |||
| IpAddress as mngIPMask | |||
| Integer32 as mngTrapMask | |||
| TrapEntry | |||
| SEQUENCE | |||
| Integer32 as trapID | |||
| DisplayString as trapVal | |||
| TimeTicks as trapTimeSinceOccurrence | |||
| IntSwdlEntry | |||
| SEQUENCE | |||
| Integer32 as intSwdlObjIdx | |||
| Integer32 as intSwdlFileIdx | |||
| DisplayString as intSwdlFileName | |||
| DisplayString as intSwdlFileSwVer | |||
| DisplayString as intSwdlSwDate | |||
| DisplayString as intSwdlSize | |||
| INTEGER as intSwdlCmd | |||
| OCTET STRING as intSwdlToSubSystem | |||
| SwdlStatusEntry | |||
| SEQUENCE | |||
| Integer32 as swdlStatusTypeIdx | |||
| Integer32 as swdlStatusIdx | |||
| DisplayString as swdlStatusFileName | |||
| DisplayString as swdlStatusSlot | |||
| DisplayString as swdlStatusSubSystem | |||
| Integer32 as swdlStatusStatus | |||
| DisplayString as swdlStatusTime | |||
| PhysicalConnectorEntry | |||
| SEQUENCE | |||
| Integer32 as portIdx | |||
| INTEGER as physicalConnector | |||
| INTEGER as portOptWaveLength | |||
| INTEGER as portOptMode | |||
| PrtSpEntry | |||
| SEQUENCE | |||
| Integer32 as prtSupervisoryIndex | |||
| INTEGER as prtSupervisoryRate | |||
| INTEGER as prtSupervisoryDataBits | |||
| INTEGER as prtSupervisoryParity | |||
| INTEGER as prtSupervisoryStopBits | |||
| INTEGER as prtSupervisoryUsage | |||
| INTEGER as prtSupervisoryInterface | |||
| INTEGER as prtSupervisoryCTS | |||
| INTEGER as prtSupervisoryDcdDelay | |||
| INTEGER as prtSupervisoryDSR | |||
| INTEGER as prtSupervisoryRoutProtocol | |||
| PrtPerfEntry | |||
| SEQUENCE | |||
| Integer32 as prtPerfIdx | |||
| INTEGER as prtPerfPeriodRef | |||
| Integer32 as prtPerfElapsedTime | |||
| Integer32 as prtPerfUAS | |||
| Integer32 as prtPerfES | |||
| Integer32 as prtPerfSES | |||
| Integer32 as prtPerfBBE | |||
| Integer32 as prtPerfBlocksPerSec | |||
| TimeTicks as prtPerfTimeTag | |||
| INTEGER as prtPerfSaveAndResetCmd | |||
| PrtTestEntry | |||
| SEQUENCE | |||
| Integer32 as prtTestIdx | |||
| Integer32 as prtTestCmdAndStatus | |||
| Integer32 as prtBertCounter | |||
| INTEGER as prtTestInitiator | |||
| Integer32 as prtTestTimeout | |||
| PrtParamEntry | |||
| SEQUENCE | |||
| Integer32 as prtParamIdx | |||
| Integer32 as prtControlCnfg | |||
| INTEGER as prtParamClkSrc | |||
| INTEGER as prtParamPhantom | |||
| INTEGER as prtParamResetStatsCmd | |||
| TimeStamp as prtParamLastResetStatsTime | |||
| PrtIpParamEntry | |||
| SEQUENCE | |||
| Integer32 as prtIpParamConfigIdx | |||
| Integer32 as prtIpParamSlotIdx | |||
| Integer32 as prtIpParamIdx | |||
| IpAddress as prtIpParamHostIP | |||
| IpAddress as prtIpParamHostMask | |||
| IpAddress as prtIpParamDefaultGateway | |||
| INTEGER as prtIpParamMediaMode | |||
| INTEGER as prtIpParamMediaRate | |||
| INTEGER as prtIpParamMngVlanSupport | |||
| Integer32 as prtIpParamMngVlanId | |||
| Integer32 as prtIpParamMngVlanPriority | |||
| INTEGER as prtIpParamRingMode | |||
| SystemPsEntry | |||
| SEQUENCE | |||
| Integer32 as systemPsIndex1 | |||
| Integer32 as systemPsIndex2 | |||
| INTEGER as systemPsType | |||
| INTEGER as systemPsStatus | |||
| INTEGER as systemPsHotSwap | |||
| XcEntry | |||
| SEQUENCE | |||
| Integer32 as xcIndex | |||
| Integer32 as xcIfIndex1 | |||
| Integer32 as xcVpi | |||
| Integer32 as xcVci | |||
| Integer32 as xcIfIndex2 | |||
| RowStatus as xcRowStatus | |||
| DisplayString as xcDescr | |||
| INTEGER as xcAdminStatus | |||
| INTEGER as xcOperStatus | |||
| ModlParamEntry | |||
| SEQUENCE | |||
| Integer32 as modlParamIndex | |||
| INTEGER as modlParamReset | |||
| INTEGER as modlParamSwdlStatus | |||
| OCTET STRING as modlParamLeds | |||
| SegTREntry | |||
| SEQUENCE | |||
| Integer32 as segTRID | |||
| Integer32 as segTRLastSlot | |||
| Integer32 as segTRFirstSlot | |||
| INTEGER as segTRStatus | |||
| MdlTREntry | |||
| SEQUENCE | |||
| Integer32 as mdlTRID | |||
| Integer32 as mdlTRSegID | |||
| INTEGER as mdlTRType | |||
| DisplayString as mdlTRHwVer | |||
| DisplayString as mdlTRSwVer | |||
| Integer32 as mdlTRTotalNoOfPrt | |||
| OBJECT IDENTIFIER as mdlTRSpecific | |||
| PrtTREntry | |||
| SEQUENCE | |||
| Integer32 as prtTRModuleID | |||
| Integer32 as prtTRID | |||
| INTEGER as prtTRFunctionality | |||
| INTEGER as prtTRConnectorType | |||
| INTEGER as prtTRAdminCmd | |||
| INTEGER as prtTRActiveState | |||
| INTEGER as prtTRTrapMaskEnable | |||
| INTEGER as prtTRstatus | |||
| INTEGER as prtTRCableProtectEnable | |||
| INTEGER as prtTRCableState | |||
| MacAddress as prtTRMACAddress | |||
| OBJECT IDENTIFIER as prtTRSpecific | |||
| PrtTRMacAddressEntry | |||
| SEQUENCE | |||
| Integer32 as prtTRMacAddressModuleID | |||
| Integer32 as prtTRMacAddressPortID | |||
| Integer32 as prtTRMacAddressID | |||
| MacAddress as prtTRMACAddressValue | |||
| SegRRSecEntry | |||
| SEQUENCE | |||
| Integer32 as segRRID | |||
| Integer32 as segRRSecID | |||
| INTEGER as segRRSecEnable | |||
| MacAddress as segRRSecurityPattern | |||
| MacAddress as segRRSecurityMask | |||
| MdlRREntry | |||
| SEQUENCE | |||
| Integer32 as mdlRRid | |||
| INTEGER as mdlRRTLRstatus | |||
| INTEGER as mdlRRtermination | |||
| INTEGER as mdlRRReset | |||
| OCTET STRING as mdlRRLed | |||
| INTEGER as mdlRRSpeed | |||
| INTEGER as mdlRRMngAutoDis | |||
| INTEGER as mdlRRAutodisable | |||
| OCTET STRING as mdlRRConfigMsg | |||
| INTEGER as mdlRRMngState | |||
| INTEGER as mdlRRType | |||
| DisplayString as mdlRRHwVer | |||
| DisplayString as mdlRRSwVer | |||
| OBJECT IDENTIFIER as mdlRRSpecific | |||
| MdlIBEntry | |||
| SEQUENCE | |||
| Integer32 as mdlIBid | |||
| Integer32 as mdlIBsegID | |||
| INTEGER as mdlIBCorrelationEnable | |||
| INTEGER as mdlIBAutorecEnable | |||
| INTEGER as mdlIBAutorecResult | |||
| INTEGER as mdlIBcommand | |||
| INTEGER as mdlIBstate | |||
| INTEGER as mdlIBagnt | |||
| IpAddress as mdlIBIpAddress | |||
| MacAddress as mdlIBLocalMacAddr | |||
| MacAddress as mdlIBbrnInMacAddr | |||
| INTEGER as mdlIBLocalAddrStatus | |||
| INTEGER as mdlIBTrapMaskEnable | |||
| MdlBRGEntry | |||
| SEQUENCE | |||
| Integer32 as mdlBRGid | |||
| INTEGER as mdlBRGReady | |||
| DisplayString as mdlBRGStatus | |||
| INTEGER as mdlBRGLocation | |||
| IpAddress as mdlBRGIpAddress | |||
| MacAddress as mdlBRGMacAddr | |||
| INTEGER as mdlBRGAdapterState | |||
| INTEGER as mdlBRGBypassSw | |||
| MdlMMEntry | |||
| SEQUENCE | |||
| Integer32 as mdlMMid | |||
| INTEGER as mdlMMBertCmd | |||
| MdlETEntry | |||
| SEQUENCE | |||
| Integer32 as mdlETid | |||
| INTEGER as mdlETSAmode | |||
| PrtRREntry | |||
| SEQUENCE | |||
| Integer32 as prtRRmdlID | |||
| Integer32 as prtRRID | |||
| INTEGER as prtRRSecurityState | |||
| INTEGER as prtRRSecurityEnable | |||
| MacAddress as prtRRSecurityMask | |||
| MacAddress as prtRRSecurityPattern | |||
| INTEGER as prtRRJitterAttenEnable | |||
| OCTET STRING as prtRRConfigMsg | |||
| INTEGER as prtRRFlipAutoDisable | |||
| MacAddress as prtRRSecurityMask2 | |||
| MacAddress as prtRRSecurityPattern2 | |||
| INTEGER as prtRRMode | |||
| INTEGER as prtRRAttachment | |||
| PrtMMEntry | |||
| SEQUENCE | |||
| Integer32 as prtMMmdlID | |||
| Integer32 as prtMMID | |||
| INTEGER as prtMMAdminCmd | |||
| INTEGER as prtMMOperStatus | |||
| INTEGER as prtMMTestStatus | |||
| INTEGER as prtMMBertResult | |||
| INTEGER as prtMMTrapMaskEnable | |||
| PrtETEntry | |||
| SEQUENCE | |||
| Integer32 as prtETmdlID | |||
| Integer32 as prtETID | |||
| INTEGER as prtETTrapMaskEnable | |||
| PrtRRSecEntry | |||
| SEQUENCE | |||
| Integer32 as prtRRSecmdlID | |||
| Integer32 as prtRRSecPrtID | |||
| Integer32 as prtRRSecID | |||
| MacAddress as prtRRSecMask | |||
| MacAddress as prtRRSecPattern | |||
| RadFddiStationEntry | |||
| SEQUENCE | |||
| Integer32 as radFddiStationIndex | |||
| INTEGER as radFddiStationType | |||
| INTEGER as radFddiStationBus1TestResult | |||
| INTEGER as radFddiStationBus2TestResult | |||
| INTEGER as radFddiStationTempDeInsertAction | |||
| INTEGER as radFddiStationPerformTest | |||
| INTEGER as radFddiStationOpticalSwitchStatus | |||
| RadFddiSMTEntry | |||
| SEQUENCE | |||
| Integer32 as radFddiSMTIndex | |||
| Integer32 as radFddiSMTStation | |||
| INTEGER as radFddiSMTCFState | |||
| Integer32 as radFddiSMTLeftSlot | |||
| Integer32 as radFddiSMTRightSlot | |||
| RadFddiMACEntry | |||
| SEQUENCE | |||
| Integer32 as radFddiMACSMTIndex | |||
| Integer32 as radFddiMACIndex | |||
| Integer32 as radFddiMACStation | |||
| Integer32 as radFddiMACTestResult | |||
| Counter32 as radFddiMACTokenCt | |||
| Integer32 as radFddiMACRingLoad | |||
| OCTET STRING as radFddiMACRingLoadBuffer | |||
| Integer32 as radFddiMACRingLoadTrsh | |||
| Integer32 as radFddiMACRingLoadPeak | |||
| OCTET STRING as radFddiMACDownstreamNbr | |||
| INTEGER as radFddiMACRingStatus | |||
| Integer32 as radFddiMACRingUtilization | |||
| Integer32 as radFddiMACRingPeakUtilization | |||
| RadFddiGroupEntry | |||
| SEQUENCE | |||
| Integer32 as radFddiGroupId | |||
| INTEGER as radFddiGroupRedundancy | |||
| INTEGER as radFddiGroupTopologyMode | |||
| INTEGER as radFddiGroupTestResult | |||
| INTEGER as radFddiGroupConfigStatus | |||
| INTEGER as radFddiGroupAutoRightLoop | |||
| INTEGER as radFddiGroupAutoLeftLoop | |||
| INTEGER as radFddiGroupManRightLoop | |||
| INTEGER as radFddiGroupManLeftLoop | |||
| INTEGER as radFddiGroupOpticalSwitchStatus | |||
| RadFddiPortEntry | |||
| SEQUENCE | |||
| Integer32 as radFddiPortGroupID | |||
| Integer32 as radFddiPortID | |||
| INTEGER as radFddiPortTestResult | |||
| Integer32 as radFddiPortNumberOfConnectedStations | |||
| OCTET STRING as radFddiPortConnectedStations | |||
| INTEGER as radFddiPortCurrentPath | |||
| INTEGER as radFddiPortFunctionalStatus | |||
| RadBridgeMaskEntry | |||
| SEQUENCE | |||
| INTEGER as radBridgeMaskType | |||
| Integer32 as radBridgeMaskIfIndex | |||
| Integer32 as radBridgeMaskNum | |||
| INTEGER as radBridgeMaskDest | |||
| OCTET STRING as radBridgeMaskPat1 | |||
| OCTET STRING as radBridgeMaskActiveBit1 | |||
| INTEGER as radBridgeMaskFrom1 | |||
| Integer32 as radBridgeMaskOffset1 | |||
| INTEGER as radBridgeMaskCond1 | |||
| OCTET STRING as radBridgeMaskPat2 | |||
| OCTET STRING as radBridgeMaskActiveBit2 | |||
| INTEGER as radBridgeMaskFrom2 | |||
| Integer32 as radBridgeMaskOffset2 | |||
| INTEGER as radBridgeMaskCond2 | |||
| OCTET STRING as radBridgeMaskPat3 | |||
| OCTET STRING as radBridgeMaskActiveBit3 | |||
| INTEGER as radBridgeMaskFrom3 | |||
| Integer32 as radBridgeMaskOffset3 | |||
| INTEGER as radBridgeMaskCond3 | |||
| INTEGER as radBridgeMaskOper | |||
| RadBridgeCODEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeCODIfIndex | |||
| INTEGER as radBridgeCODManualConnect | |||
| INTEGER as radBridgeCODMode | |||
| Integer32 as radBridgeCODConnectDelay | |||
| Integer32 as radBridgeCODisConnectDelay | |||
| INTEGER as radBridgeCODImplicitSwitch | |||
| Counter32 as radBridgeCODNumAccess | |||
| Integer32 as radBridgeCODTotalConnecTime | |||
| RadBridgeCODTimeTriggerEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeCODTimeIfIndex | |||
| INTEGER as radBridgeCODDay | |||
| Integer32 as radBridgeCODTimeTriggerNum | |||
| DisplayString as radBridgeCODTimeTriggerFrom | |||
| DisplayString as radBridgeCODTimeTriggerTo | |||
| INTEGER as radBridgeCODTimeTriggerStatus | |||
| RadBridgeCODTrafficEntry | |||
| SEQUENCE | |||
| INTEGER as radBridgeCODProtocolType | |||
| INTEGER as radBridgeCODTrafficTriggerStatus | |||
| RadBridgeCODCondEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeCODCondIfIndex | |||
| INTEGER as radBridgeCODOriginateConnectCondition | |||
| INTEGER as radBridgeCODOriginateDisConnectCondition | |||
| Integer32 as radBridgeCODOriginateDisConnectDelay | |||
| INTEGER as radBridgeCODAnswerConnectCondition | |||
| OBJECT IDENTIFIER as radBridgeCODSpecificOnTrafficOIDCondition | |||
| Integer32 as radBridgeCODDisConnectMinimunFramesNumber | |||
| RadBridgeIPXRipTableEntry | |||
| SEQUENCE | |||
| OCTET STRING as radBridgeIPXRipDestNetwork | SIZE(4) | ||
| INTEGER as radBridgeIPXRipPolicy | |||
| OCTET STRING as radBridgeIPXRipForwardingRouter | SIZE(6) | ||
| Integer32 as radBridgeIPXRipNIC | |||
| Integer32 as radBridgeIPXRipTickMetric | |||
| Integer32 as radBridgeIPXRipHopMetric | |||
| TimeTicks as radBridgeIPXRipAgingTime | |||
| INTEGER as radBridgeIPXRipValueStatus | |||
| INTEGER as radBridgeIPXRipForwardType | |||
| RadBridgeIPXRipInfEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeIPXRipInfIfIndex | |||
| Integer32 as radBridgeIPXRipInfBcastUpdate | |||
| Integer32 as radBridgeIPXRipInfAgeMultiplier | |||
| RadBridgeIPXSapTableEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeIPXSapServerType | |||
| DisplayString as radBridgeIPXSapName | SIZE(48) | ||
| OCTET STRING as radBridgeIPXSapNetwork | SIZE(4) | ||
| OCTET STRING as radBridgeIPXSapNode | SIZE(6) | ||
| Integer32 as radBridgeIPXSapSocket | |||
| Integer32 as radBridgeIPXSapHopsToServer | |||
| Integer32 as radBridgeIPXSapNIC | |||
| TimeTicks as radBridgeIPXSapAgingTime | |||
| INTEGER as radBridgeIPXSapStatus | |||
| RadBridgeIPXSapInfEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeIPXSapInfIfIndex | |||
| Integer32 as radBridgeIPXSapInfBcastUpdate | |||
| Integer32 as radBridgeIPXSapInfAgeMultiplier | |||
| GenAddress | |||
| OCTET STRING | SIZE(12) | ||
| MaskingEntry | |||
| SEQUENCE | |||
| INTEGER as maskingType | |||
| Integer32 as maskingIfIndex | |||
| Integer32 as maskingIndex | |||
| INTEGER as maskingProtocolType | |||
| OBJECT IDENTIFIER as maskingSmartMaskOID | |||
| INTEGER as maskingFrameType | |||
| INTEGER as maskingFrameTypeCondition | |||
| GenAddress as maskingSourceAddress | |||
| GenAddress as maskingSourceActiveBits | |||
| INTEGER as maskingSourceMacOrNet | |||
| INTEGER as maskingSourceCondition | |||
| GenAddress as maskingDestAddress | |||
| GenAddress as maskingDestActiveBits | |||
| INTEGER as maskingDestMacOrNet | |||
| INTEGER as maskingDestCondition | |||
| INTEGER as maskingLowLevelProt | |||
| INTEGER as maskingLowLevelProtCondition | |||
| Integer32 as maskingHighLevelProt | |||
| INTEGER as maskingHighLevelProtCondition | |||
| Integer32 as maskingPortNum | |||
| INTEGER as maskingPortNumCondition | |||
| INTEGER as maskingOperation | |||
| Integer32 as maskingSrcPortNum | |||
| INTEGER as maskingSrcPortNumCondition | |||
| RadBridgeCurrentEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeCurrentIndex | |||
| Gauge32 as radBridgeCurrentIngressFilteringDiscardedFrames | |||
| Gauge32 as radBridgeCurrentFrameTypeDiscardedFrames | |||
| RadBridgeIntervalEntry | |||
| SEQUENCE | |||
| Integer32 as radBridgeIntervalIndex | |||
| Integer32 as radBridgeIntervalNumber | |||
| Gauge32 as radBridgeIntervalIngressFilteringDiscardedFrames | |||
| Gauge32 as radBridgeIntervalFrameTypeDiscardedFrames | |||
| TrimIfEntry | |||
| SEQUENCE | |||
| Integer32 as trimIfIndex | |||
| Integer32 as trimIfBoardNum | |||
| IpAddress as trimIfNetAddress | |||
| INTEGER as trimIfStatus | |||
| INTEGER as trimIfClockType | |||
| Integer32 as trimIfBaudRate | |||
| Integer32 as trimIfCost | |||
| INTEGER as trimIfCompression | |||
| INTEGER as trimIfCompressionStatus | |||
| Integer32 as trimIfCompressionRate | |||
| INTEGER as trimIfLATCompression | |||
| INTEGER as trimIfCompressionType | |||
| INTEGER as trimIfFilterMode | |||
| INTEGER as trimIfConType | |||
| DisplayString as trimIfRemAddress | |||
| DisplayString as trimIfLocSubAddress | |||
| DisplayString as trimIfRemSubAddress | |||
| INTEGER as trimIfCLIVerification | |||
| TrimIfThresholdRepEntry | |||
| SEQUENCE | |||
| Integer32 as trimIfThreRepId | |||
| INTEGER as trimIfThreRepCounterId | |||
| Integer32 as trimThresholdValue | |||
| Integer32 as trimIfThreRepSampleRate | |||
| Integer32 as trimIfThreRepTrapRate | |||
| TrimBackUpEntry | |||
| SEQUENCE | |||
| Integer32 as trimBackUpDay | |||
| DisplayString as trimBackUpFromTo | |||
| TrimTRIfEntry | |||
| SEQUENCE | |||
| Integer32 as trimTRIfIndex | |||
| INTEGER as trimTREarlyTokenRelease | |||
| MacAddress as trimTRLocalAdminAddress | |||
| INTEGER as trimTRLocalAdminAddressStatus | |||
| LanrangerBootPEntry | |||
| SEQUENCE | |||
| IpAddress as lanrangerBootPIpAddress | |||
| INTEGER as lanrangerBootPIfIndex | |||
| INTEGER as lanrangerBootPOperation | |||
| LanrangerLinkEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerLinkIndex | |||
| INTEGER as lanrangerLinkType | |||
| INTEGER as lanrangerLinkState | |||
| INTEGER as lanrangerLinkDTRMode | |||
| INTEGER as lanrangerLinkStatus | |||
| INTEGER as lanrangerLinkConnectionStatus | |||
| Integer32 as lanrangerLinkNumOfLogLinks | |||
| INTEGER as lanrangerLinkReset | |||
| Counter32 as lanrangerLinkRxMaskedFrames | |||
| INTEGER as lanrangerLinkLayer2Type | |||
| INTEGER as lanrangerLinkLayer3Type | |||
| Integer32 as lanrangerBackupLink | |||
| Integer32 as wrWanThrottle | |||
| LanrangerLinkConnEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerLinkConnPhysLink | |||
| Integer32 as lanrangerLinkConnAid | |||
| MacAddress as lanrangerLinkConnMacAddr | |||
| INTEGER as lanrangerLinkConnStatus | |||
| INTEGER as lanrangerLinkConnDeviceType | |||
| DisplayString as lanrangerLinkConnDeviceName | |||
| DisplayString as lanrangerLinkConnDeviceSWVer | |||
| Integer32 as lanrangerLinkConnNumLanStation | |||
| INTEGER as lanrangerLinkSyncStatus | |||
| LanrangerModemEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerModemLinkIndex | |||
| DisplayString as lanrangerModemName | |||
| DisplayString as lanrangerModemSettingString | |||
| INTEGER as lanrangerModemAutobaudingSpeed | |||
| INTEGER as lanrangerModemResetBeforeSetup | |||
| INTEGER as lanrangerModemAnalyzeAnswers | |||
| INTEGER as lanrangerModemSpeaker | |||
| DisplayString as lanrangerModemDialingNumber | |||
| Integer32 as lanrangerModemDialRetries | |||
| DisplayString as wrLocalDialBackNumber | |||
| Integer32 as wrRingsBeforeAnswer | |||
| LanrangerLinkPktSwEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerLinkPktSwIndex | |||
| INTEGER as lanrangerLinkPktSwType | |||
| INTEGER as lanrangerLinkPktSwControlSignal | |||
| Integer32 as lanrangerLinkPktSwSpeed | |||
| INTEGER as lanrangerLinkPktSwConfigParity | |||
| INTEGER as lanrangerLinkPktSwConfigStopBit | |||
| INTEGER as lanrangerLinkPktSwResetModule | |||
| LanrangerStationEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerStationPhysLink | |||
| Integer32 as lanrangerStationLogLink | |||
| MacAddress as lanrangerStationAddress | |||
| INTEGER as lanrangerStationStatus | |||
| INTEGER as lanrangerStationSpoofingStatus | |||
| LanrangerPermanentEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerPermanentIfIndex | |||
| Integer32 as lanrangerPermanentLogLink | |||
| MacAddress as lanrangerPermanentAddress | |||
| INTEGER as lanrangerPermanentOperation | |||
| LanrangerSpoofingEntry | |||
| SEQUENCE | |||
| Integer32 as lanrangerSpoofingGroup | |||
| MacAddress as lanrangerSpoofingMacAddress | |||
| Integer32 as lanrangerSpoofingAging | |||
| Integer32 as lanrangerSpoofingTimeLeft | |||
| WrPPPEntry | |||
| SEQUENCE | |||
| INTEGER as wrPPPCompressionHeaderField | |||
| INTEGER as wrPPPCompressionProtocolFields | |||
| INTEGER as wrPPPSTACCompressionType | |||
| INTEGER as wrPPPAuthProtocol | |||
| INTEGER as wrPPPSecurityType | |||
| SnmpAdminString as wrPPPUserName | |||
| SnmpAdminString as wrPPPPassword | |||
| Integer32 as wrPPPLinkActiveTime | |||
| FebFtbTranslIfEntry | |||
| SEQUENCE | |||
| Integer32 as febFtbTranslIfIndex | |||
| OCTET STRING as febFtbTunnelProtocol | |||
| INTEGER as febFtbTranslIPXRawEthernet | |||
| FebFtbLanTabEntry | |||
| SEQUENCE | |||
| Integer32 as febFtbLanTabIfIndex | |||
| Integer32 as febFtbLanTabEntNumber | |||
| MlbAddressEntry | |||
| SEQUENCE | |||
| Integer32 as mlbPortIndex | |||
| MacAddress as mlbBurnAddress | |||
| MacAddress as mlbLocAddress | |||
| INTEGER as mlbActiveAddress | |||
| Sap | |||
| OCTET STRING | SIZE(1) | ||
| SdlcAddr | |||
| OCTET STRING | SIZE(1) | ||
| NvaAgentEntry | |||
| SEQUENCE | |||
| Integer32 as nvaAgIndex | |||
| INTEGER as nvaAgAdminStatus | |||
| INTEGER as nvaAgOperState | |||
| OCTET STRING as nvaAgFilter | |||
| INTEGER as nvaAgAllowRunCmd | |||
| INTEGER as nvaAgAccessType | |||
| Integer32 as nvaAgIfIndex | |||
| OCTET STRING as nvaAgXidBlockId | |||
| OCTET STRING as nvaAgXidBlockNum | |||
| Sap as nvaAgSSap | |||
| Sap as nvaAgDSap | |||
| MacAddress as nvaAgRemMacAddr | |||
| SdlcAddr as nvaAgSdlcAddr | |||
| DisplayString as nvaAgResourceName | |||
| NvaAgentStatEntry | |||
| SEQUENCE | |||
| Integer32 as nvaAgStatIndex | |||
| TimeTicks as nvaAgStatTime | |||
| Counter32 as nvaAgActPu | |||
| Counter32 as nvaAgDactPu | |||
| Counter32 as nvaAgRpNmvt | |||
| Counter32 as nvaAgRnNmvt | |||
| Counter32 as nvaAgSpNmvt | |||
| Counter32 as nvaAgSAlerts | |||
| Counter32 as nvaAgRRunCmd | |||
| Counter32 as nvaAgSRunCmd | |||
| Counter32 as nvaAgSPdstat | |||
| SnaSessEntry | |||
| SEQUENCE | |||
| Integer32 as sessIfIndex | |||
| Integer32 as sessId | |||
| INTEGER as sessSide | |||
| Integer32 as sessDev | |||
| INTEGER as sessAdminStatus | |||
| INTEGER as sessOperState | |||
| INTEGER as sessAccessType | |||
| OCTET STRING as sessSXidBlockId | |||
| OCTET STRING as sessSXidBlockNum | |||
| Sap as sessSSap | |||
| Sap as sessDSap | |||
| MacAddress as sessRemMacAddr | |||
| SdlcAddr as sessSdlcAddr | |||
| SdlcAddr as sessGroupPoll | |||
| INTEGER as sessRole | |||
| INTEGER as sessIpEncapsulated | |||
| IpAddress as sessDestIpAddr | |||
| OCTET STRING as sessRemX25Addr | |||
| SnaSessTuneEntry | |||
| SEQUENCE | |||
| Integer32 as sessTuneIfIndex | |||
| Integer32 as sessTuneId | |||
| INTEGER as sessTuneSide | |||
| Integer32 as sessBufferSize | |||
| INTEGER as sessSegmentation | |||
| INTEGER as sessFirstSide | |||
| Integer32 as sessWindow | |||
| INTEGER as sessDuplex | |||
| OCTET STRING as sessRXidBlockId | |||
| OCTET STRING as sessRXidBlockNum | |||
| INTEGER as sessCheckXid | |||
| Integer32 as sessT1 | |||
| Integer32 as sessTi | |||
| Integer32 as sessT2 | |||
| Integer32 as sessN2 | |||
| Integer32 as sessUdpPort | |||
| SnaSessStatEntry | |||
| SEQUENCE | |||
| Integer32 as sessStatIfIndex | |||
| Integer32 as sessStatId | |||
| INTEGER as sessStatSide | |||
| TimeTicks as sessStatTime | |||
| Counter32 as sessSPius | |||
| Counter32 as sessSBytes | |||
| Counter32 as sessRPius | |||
| Counter32 as sessRBytes | |||
| Counter32 as sessSessFailure | |||
| Counter32 as sessXidDenieds | |||
| SnaSessQllcEntry | |||
| SEQUENCE | |||
| Integer32 as sessQllcIfIndex | |||
| Integer32 as sessQllcId | |||
| INTEGER as sessQllcSide | |||
| INTEGER as sessInCalls | |||
| INTEGER as sessOutCalls | |||
| INTEGER as sessPVC | |||
| OCTET STRING as sessCallReqData | |||
| OCTET STRING as sessConnReqFacility | |||
| OCTET STRING as sessGroupId | |||
| OCTET STRING as sessDtePswd | |||
| OCTET STRING as sessDteId | |||
| Integer32 as sessMaxInPktSize | |||
| Integer32 as sessMaxOutPktSize | |||
| OCTET STRING as sessCallIndReverse | |||
| SdlcEntry | |||
| SEQUENCE | |||
| Integer32 as sdlcIfIndex | |||
| INTEGER as sdlcNrz | |||
| INTEGER as sdlcDuplex | |||
| INTEGER as sdlcClockType | |||
| Integer32 as sdlcSpeed | |||
| DisplayString as sdlcConnectorType | |||
| INTEGER as sdlcRts | |||
| SdlcStatEntry | |||
| SEQUENCE | |||
| Integer32 as sdlcStatIfIndex | |||
| TimeTicks as sdlcTimeSinceReset | |||
| Counter32 as sdlcStatFramesTrans | |||
| Counter32 as sdlcStatBytesTrans | |||
| Counter32 as sdlcStatFramesRcv | |||
| Counter32 as sdlcStatBytesRcv | |||
| Counter32 as sdlcStatFramesAbort | |||
| Counter32 as sdlcStatFramesBad | |||
| Counter32 as sdlcStatFramesCrc | |||
| CvtDot5Entry | |||
| SEQUENCE | |||
| Integer32 as cvtDot5IfIndex | |||
| MacAddress as cvtDot5MacAddr | |||
| INTEGER as cvtDot5Commands | |||
| INTEGER as cvtDot5RingSpeed | |||
| INTEGER as cvtDot5ActMonParticipate | |||
| MacAddress as cvtDot5Functional | |||
| CvtDot3Entry | |||
| SEQUENCE | |||
| Integer32 as cvtDot3IfIndex | |||
| MacAddress as cvtDot3MacAddr | |||
| INTEGER as cvtDot3Commands | |||
| INTEGER as cvtDot3ActMonParticipate | |||
| MacAddress as cvtDot3Functional | |||
| StkHubSecurityEntry | |||
| SEQUENCE | |||
| Integer32 as stkHubSecID | |||
| INTEGER as stkHubSecEnable | |||
| OCTET STRING as stkHubSecurityPattern | |||
| OCTET STRING as stkHubSecurityMask | |||
| StkHubPrtSecurityEntry | |||
| SEQUENCE | |||
| Integer32 as stkHubModuleID | |||
| Integer32 as stkHubPrtID | |||
| Integer32 as stkHubPrtSecID | |||
| INTEGER as stkHubPrtSecurityEnable | |||
| OCTET STRING as stkHubPrtSecurityPattern | |||
| OCTET STRING as stkHubPrtSecurityMask | |||
| StkHubTRMdlEntry | |||
| SEQUENCE | |||
| Integer32 as stkHubTRMdlID | |||
| INTEGER as stkHubTRMdlType | |||
| INTEGER as stkHubTRMdlReset | |||
| OCTET STRING as stkHubTRMdlLed | |||
| INTEGER as stkHubTRMdlSpeed | |||
| INTEGER as stkHubTRMdlMngState | |||
| INTEGER as stkHubTRMdlAutodisable | |||
| OCTET STRING as stkHubTRMdlConfigMsg | |||
| StkHubTRPrtEntry | |||
| SEQUENCE | |||
| Integer32 as stkHubTRPrtMdlID | |||
| Integer32 as stkHubTRPrtID | |||
| INTEGER as stkHubTRPrtFunctionality | |||
| INTEGER as stkHubTRPrtConnectorType | |||
| INTEGER as stkHubTRPrtAdminCmd | |||
| INTEGER as stkHubTRPrtActiveState | |||
| INTEGER as stkHubTRPrtTrapMaskEnable | |||
| INTEGER as stkHubTRPrtStatus | |||
| INTEGER as stkHubTRPrtCableProtectEnable | |||
| INTEGER as stkHubTRPrtFlipProtectEnable | |||
| MacAddress as stkHubTRPrtMACAddress | |||
| INTEGER as stkHubTRPrtType | |||
| StkHubETMdlEntry | |||
| SEQUENCE | |||
| Integer32 as stkHubETMdlID | |||
| OCTET STRING as stkHubETMdlLed | |||
| INTEGER as stkHubETMdlReset | |||
| EtRptrEntry | |||
| SEQUENCE | |||
| Integer32 as etRptrIndex | |||
| Integer32 as etRptrGroupCapacity | |||
| INTEGER as etRptrOperStatus | |||
| DisplayString as etRptrHealthText | |||
| INTEGER as etRptrReset | |||
| INTEGER as etRptrNonDisruptTest | |||
| Gauge32 as etRptrTotalPartitionedPorts | |||
| Integer32 as etRptrMdlVector | |||
| Counter32 as etRptrMonitorTransmitCollisions | |||
| EtRptrSecEntry | |||
| SEQUENCE | |||
| Integer32 as etRptrId | |||
| Integer32 as etRptrSecID | |||
| INTEGER as etRptrSecEnable | |||
| OCTET STRING as etRptrSecPattern | |||
| OCTET STRING as etRptrSecMask | |||
| AgnSAlrEntry | |||
| SEQUENCE | |||
| Integer32 as agnSAlrIdx | |||
| DisplayString as agnSAlrCodeDescription | SIZE(0..255) | ||
| Integer32 as agnSAlrCode | |||
| INTEGER as agnSAlrSeverity | |||
| INTEGER as agnSAlrState | |||
| Integer32 as agnSAlrCounter | |||
| INTEGER as agnSAlrMask | |||
| INTEGER as agnSAlrInvert | |||
| AgnSErrListEntry | |||
| SEQUENCE | |||
| Integer32 as agnSErrIdx | |||
| DisplayString as agnSErrDescription | SIZE(0..255) | ||
| AgnSCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as agnSEntryIdx | |||
| INTEGER as agnSEntryIsValid | |||
| AgnCClkSrcEntry | |||
| SEQUENCE | |||
| Integer32 as agnCClkCnfgIdx | |||
| Integer32 as agnCClkSrcIdx | |||
| INTEGER as agnCClkSrcMode | |||
| INTEGER as agnCClkSrcSlt | |||
| Integer32 as agnCClkSrcPrt | |||
| AgnCnfgDataEntry | |||
| SEQUENCE | |||
| Integer32 as agnCnfgIdx | |||
| DisplayString as agnCnfgDesc | |||
| DisplayString as agnCnfgUpdDate | |||
| DisplayString as agnCnfgUpdTime | |||
| IpAddress as agnCnfgUpdMnger | |||
| AgnCnfgAlrEntry | |||
| SEQUENCE | |||
| Integer32 as agnCnfgAlrCode | |||
| INTEGER as agnCnfgAlrSlot | |||
| Integer32 as agnCnfgAlrPort | |||
| INTEGER as agnCnfgAlrMask | |||
| INTEGER as agnCnfgAlrInvert | |||
| INTEGER as agnCnfgAlrFilter | |||
| Integer32 as agnCnfgAlrFilterSet | |||
| Integer32 as agnCnfgAlrFilterReset | |||
| AgnCnfgAlrReportEntry | |||
| SEQUENCE | |||
| INTEGER as agnCnfgAlrReportType | |||
| INTEGER as agnCnfgAlrStartReportOn | |||
| INTEGER as agnCnfgAlrStartReportOff | |||
| AgnCT1E1RingEntry | |||
| SEQUENCE | |||
| Integer32 as agnCT1E1RingCnfgIdx | |||
| INTEGER as agnCT1E1RingPrimeSlot | |||
| Integer32 as agnCT1E1RingPrimePort | |||
| INTEGER as agnCT1E1RingSecSlot | |||
| Integer32 as agnCT1E1RingSecPort | |||
| Integer32 as agnCT1E1RingRecTime | |||
| RowStatus as agnCT1E1RingRowStatus | |||
| AgnCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnCmprTypIdx | |||
| Integer32 as agnCmprCnfgIdx | |||
| Integer32 as agnCmprVersion | |||
| OCTET STRING as agnCmprObj | |||
| AgnDlciCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnDlciCmprCnfgIdx | |||
| Integer32 as agnDlciCmprVersion | |||
| Integer32 as agnDlciCmprDlciIdx | |||
| OCTET STRING as agnDlciCmprObj | |||
| AgnAlarmsCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnAlarmsCmprVersion | |||
| Integer32 as agnAlarmsCmprAlarmIdx | |||
| OCTET STRING as agnAlarmsCmprObj | |||
| AgnAlrBufCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnAlrBufCmprVersion | |||
| Integer32 as agnAlrBufCmprAlarmIdx | |||
| OCTET STRING as agnAlrBufCmprObj | |||
| AgnSCmprErrListEntry | |||
| SEQUENCE | |||
| Integer32 as agnSCmprErrVersion | |||
| Integer32 as agnSCmprErrIdx | |||
| OCTET STRING as agnSCmprErrObj | |||
| AgnTsCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnTsCmprVerIdx | |||
| Integer32 as agnTsCmprCnfgIdx | |||
| Integer32 as agnTsCmprSlotIdx | |||
| Integer32 as agnTsCmprPortIdx | |||
| Integer32 as agnTsCmprPduIdx | |||
| OCTET STRING as agnTsCmprData | |||
| AgnXCmprEntry | |||
| SEQUENCE | |||
| Integer32 as agnXCmprTypIdx | |||
| Integer32 as agnXCmprVersion | |||
| Integer32 as agnXCmprIdx3 | |||
| Integer32 as agnXCmprIdx4 | |||
| Integer32 as agnXCmprIdx5 | |||
| Integer32 as agnXCmprIdx6 | |||
| Integer32 as agnXCmprIdx7 | |||
| OCTET STRING as agnXCmprObj | |||
| AgnLinkMapEntry | |||
| SEQUENCE | |||
| Integer32 as mapLinkId | |||
| INTEGER as mapLinkSltIdx | |||
| INTEGER as mapLinkPrtIdx | |||
| INTEGER as mapLinkStatus | |||
| AlrBufEntry | |||
| SEQUENCE | |||
| Integer32 as alrBufIdx | |||
| DisplayString as alrBufDescription | SIZE(0..255) | ||
| AgnCAgendaEntry | |||
| SEQUENCE | |||
| INTEGER as agnCAgendaCnfgIdx | |||
| INTEGER as agnCAgendaDayIdx | |||
| INTEGER as agnCAgendaDayCategory | |||
| AgnCFlipNetEventsEntry | |||
| SEQUENCE | |||
| INTEGER as agnCFlipNetEventsCnfgIdx | |||
| Integer32 as agnCFlipNetEventIdx | |||
| INTEGER as agnCFlipNetEventActive | |||
| INTEGER as agnCFlipNetEventType | |||
| Integer32 as agnCFlipNetEventNo | |||
| INTEGER as agnCFlipNetEventSlot | |||
| Integer32 as agnCFlipNetEventPort | |||
| Integer32 as agnCFlipNetEventISD | |||
| Integer32 as agnCFlipNetEventOSD | |||
| INTEGER as agnCFlipNetEventDayType | |||
| DisplayString as agnCFlipNetEventStartTime | SIZE(5) | ||
| DisplayString as agnCFlipNetEventEndTime | SIZE(5) | ||
| AgnCFlipEntry | |||
| SEQUENCE | |||
| INTEGER as agnCFlipCnfgIdx | |||
| Integer32 as agnCFlipIdx | |||
| INTEGER as agnCFlipActive | |||
| DisplayString as agnCFlipLogicalExp | SIZE(1..20) | ||
| Integer32 as agnCFlipDbNo | |||
| INTEGER as agnCFlipDiscardDe | |||
| AgnListDecodingEntry | |||
| SEQUENCE | |||
| INTEGER as agnListDecodingType | |||
| Integer32 as agnListDecodingCode | |||
| DisplayString as agnListDecodingDescription | SIZE(0..255) | ||
| INTEGER as agnListDecodingDefState | |||
| INTEGER as agnListDecodingSeverity | |||
| INTEGER as agnListDecodingAcmRelaySlt | |||
| INTEGER as agnListDecodingAcmRelayPrt | |||
| AgnDlciEntry | |||
| SEQUENCE | |||
| Integer32 as agnDlciCnfgIdx | |||
| INTEGER as agnDlciLSltIdx | |||
| Integer32 as agnDlciLPrtIdx | |||
| Integer32 as agnDlciLIdx | |||
| INTEGER as agnDlciHSltIdx | |||
| Integer32 as agnDlciHPrtIdx | |||
| Integer32 as agnDlciHIdx | |||
| INTEGER as agnDlciTxBc | |||
| INTEGER as agnDlciTxBe | |||
| INTEGER as agnDlciRxBc | |||
| INTEGER as agnDlciRxBe | |||
| Integer32 as agnDlciPriority | |||
| INTEGER as agnDlciStatus | |||
| INTEGER as agnDlciSpoofing | |||
| INTEGER as agnDlciFunnelEnable | |||
| INTEGER as agnDlciRoutingProtocol | |||
| RowStatus as agnDlciRowStatus | |||
| AgnVoiceSwConfEntry | |||
| SEQUENCE | |||
| INTEGER as agnVoiceSwConfIdx | |||
| DisplayString as agnVoiceSwConfZoneId | |||
| DisplayString as agnVoiceSwConfNodeId | |||
| Integer32 as agnVoiceSwConfNoOfHops | |||
| Integer32 as agnVoiceSwConfSidt | |||
| Integer32 as agnVoiceSwConfLidt | |||
| INTEGER as agnVoiceSwConfDialPlan | |||
| AgnVoiceSwConfRtEntry | |||
| SEQUENCE | |||
| INTEGER as agnVoiceSwConfRtDbId | |||
| Integer32 as agnVoiceSwConfRtIdx | |||
| DisplayString as agnVoiceSwConfRtDigits | |||
| INTEGER as agnVoiceSwConfRtAction | |||
| DisplayString as agnVoiceSwConfRtData | |||
| INTEGER as agnVoiceSwConfRtSlot | |||
| Integer32 as agnVoiceSwConfRtPort | |||
| Integer32 as agnVoiceSwConfRtDlci | |||
| RowStatus as agnVoiceSwConfRtRowStatus | |||
| Integer32 as agnVoiceSwConfRtMaxCalls | |||
| AgnVoiceSwConfHGEntry | |||
| SEQUENCE | |||
| INTEGER as agnVoiceSwConfHGdbIdx | |||
| Integer32 as agnVoiceSwConfHGIdx | |||
| INTEGER as agnVoiceSwConfHGConnect | |||
| Integer32 as agnVoiceSwConfHGExt | |||
| AgnSigProfileEntry | |||
| SEQUENCE | |||
| Integer32 as agnSigProfileCnfgIdx | |||
| Integer32 as agnSigProfileIdx | |||
| INTEGER as agnSigProfileRxTx | |||
| OCTET STRING as agnSigProfileABCD | |||
| AgnSigProfEntry | |||
| SEQUENCE | |||
| Integer32 as agnSigProfCnfgIdx | |||
| Integer32 as agnSigProfIdx | |||
| DisplayString as agnSigProfName | |||
| INTEGER as agnSigProfType | |||
| SystemVoiceEntry | |||
| SEQUENCE | |||
| Integer32 as systemVoiceConfIdx | |||
| INTEGER as systemVoiceNationalTone | |||
| MdlSInstEntry | |||
| SEQUENCE | |||
| INTEGER as mdlSInstSltIdx | |||
| INTEGER as mdlSInstCardType | |||
| DisplayString as mdlSHwVersion | SIZE(0..255) | ||
| DisplayString as mdlSSwVersion | SIZE(0..255) | ||
| INTEGER as mdlSAlrStatus | |||
| INTEGER as mdlSAlrStatusAll | |||
| INTEGER as mdlSMaskedAlrStat | |||
| INTEGER as mdlSMaskedAlrStatAll | |||
| INTEGER as mdlSTstStatusAll | |||
| INTEGER as mdlSClearAlrCmd | |||
| INTEGER as mdlSClearAllAlrCmd | |||
| MdlSAlrEntry | |||
| SEQUENCE | |||
| INTEGER as mdlSAlrSltIdx | |||
| Integer32 as mdlSAlrIdx | |||
| DisplayString as mdlSAlrCodeDescription | SIZE(0..255) | ||
| Integer32 as mdlSAlrCode | |||
| INTEGER as mdlSAlrSeverity | |||
| INTEGER as mdlSAlrState | |||
| Integer32 as mdlSAlrCounter | |||
| INTEGER as mdlSAlrMask | |||
| INTEGER as mdlSAlrInvert | |||
| MdlCPrgEntry | |||
| SEQUENCE | |||
| Integer32 as mdlCCnfgIdx | |||
| INTEGER as mdlCSltIdx | |||
| INTEGER as mdlCPrgCardType | |||
| Integer32 as mdlCNoOfExternPrt | |||
| Integer32 as mdlCNoOfInternPrt | |||
| INTEGER as mdlCWorkMode | |||
| MdlCmprEntry | |||
| SEQUENCE | |||
| Integer32 as mdlCmprTypIdx | |||
| Integer32 as mdlCmprCnfgIdx | |||
| Integer32 as mdlCmprVersion | |||
| INTEGER as mdlCmprSltIdx | |||
| OCTET STRING as mdlCmprObj | |||
| MdlAlarmsCmprEntry | |||
| SEQUENCE | |||
| Integer32 as mdlAlarmsCmprVersion | |||
| Integer32 as mdlAlarmsCmprAlarmSlot | |||
| Integer32 as mdlAlarmsCmprAlarmIdx | |||
| OCTET STRING as mdlAlarmsCmprObj | |||
| PrtSInstEntry | |||
| SEQUENCE | |||
| INTEGER as prtSInstSltIdx | |||
| Integer32 as prtSInstPrtIdx | |||
| INTEGER as prtSInstPrtType | |||
| Integer32 as prtSInstIfIndex | |||
| INTEGER as prtSActiveStatus | |||
| INTEGER as prtSAlrStatus | |||
| INTEGER as prtSMaskedAlrStat | |||
| INTEGER as prtSClearAlrCmd | |||
| Integer32 as prtSTestMask | |||
| INTEGER as prtSTstCmd | |||
| Integer32 as prtSTstDuration | |||
| INTEGER as prtSBertClrCmd | |||
| Integer32 as prtSBertTstRslt | |||
| DisplayString as prtSInterfaceType | SIZE(0..255) | ||
| OCTET STRING as prtSParamStatus | |||
| PrtSAlrEntry | |||
| SEQUENCE | |||
| INTEGER as prtSAlrSltIdx | |||
| Integer32 as prtSAlrPrtIdx | |||
| Integer32 as prtSAlrIdx | |||
| DisplayString as prtSAlrCodeDescription | SIZE(0..255) | ||
| Integer32 as prtSAlrCode | |||
| INTEGER as prtSAlrSeverity | |||
| INTEGER as prtSAlrState | |||
| Integer32 as prtSAlrCounter | |||
| INTEGER as prtSAlrMask | |||
| INTEGER as prtSAlrInvert | |||
| PrtFrStatisEntry | |||
| SEQUENCE | |||
| INTEGER as prtFrStatisSltIdx | |||
| INTEGER as prtFrStatisPrtIdx | |||
| INTEGER as prtFrStatisInvIdx | |||
| Integer32 as prtFrTimeElapsed | |||
| Counter32 as prtFrRxTotalFrames | |||
| Counter32 as prtFrTxTotalFrames | |||
| Counter32 as prtFrRxTotalBytes | |||
| Counter32 as prtFrTxTotalBytes | |||
| Counter32 as prtFrRxMngFrames | |||
| Counter32 as prtFrTxMngFrames | |||
| Counter32 as prtFrRxDeFrames | |||
| Counter32 as prtFrTxDeFrames | |||
| Counter32 as prtFrRxDcrdCongDeFr | |||
| Counter32 as prtFrTxDcrdCongDeFr | |||
| Counter32 as prtFrRxDcrdCongAllFr | |||
| Counter32 as prtFrTxDcrdCongAllFr | |||
| Counter32 as prtFrRxFecn | |||
| Counter32 as prtFrTxFecn | |||
| Counter32 as prtFrRxBecn | |||
| Counter32 as prtFrTxBecn | |||
| Counter32 as prtFrRxBeViol | |||
| Counter32 as prtFrTxBeViol | |||
| Counter32 as prtFrRxBcViol | |||
| Counter32 as prtFrTxBcViol | |||
| PrtCrStatisEntry | |||
| SEQUENCE | |||
| INTEGER as prtCrStatisSltIdx | |||
| INTEGER as prtCrStatisPrtIdx | |||
| INTEGER as prtCrStatisInvIdx | |||
| Integer32 as prtCrTimeElapsed | |||
| Counter32 as prtCrRxTotalCells | |||
| Counter32 as prtCrTxTotalCells | |||
| Counter32 as prtCrRxDataCells | |||
| Counter32 as prtCrTxDataCells | |||
| PrtDlciStatisEntry | |||
| SEQUENCE | |||
| INTEGER as prtDlciSltIdx | |||
| INTEGER as prtDlciPrtIdx | |||
| Integer32 as prtDlciIdx | |||
| Counter32 as prtDlciRxDeFrames | |||
| Counter32 as prtDlciTxDeFrames | |||
| Counter32 as prtDlciRxDcrdCongDeFr | |||
| Counter32 as prtDlciTxDcrdCongDeFr | |||
| Counter32 as prtDlciRxDcrdCongAllFr | |||
| Counter32 as prtDlciTxDcrdCongAllFr | |||
| Counter32 as prtDlciTxFecn | |||
| Counter32 as prtDlciTxBecn | |||
| Counter32 as prtDlciRxBeViol | |||
| Counter32 as prtDlciTxBeViol | |||
| Counter32 as prtDlciRxBcViol | |||
| Counter32 as prtDlciTxBcViol | |||
| PrtT1FdlMsgEntry | |||
| SEQUENCE | |||
| INTEGER as prtT1FdlMsgSltIdx | |||
| INTEGER as prtT1FdlMsgPrtIdx | |||
| INTEGER as prtT1FdlMsgFdlTxRx | |||
| OCTET STRING as prtT1FdlMsg | |||
| PrtExTsSplitEntry | |||
| SEQUENCE | |||
| Integer32 as prtExTsCnfgIdx | |||
| INTEGER as prtExTsSltIdx | |||
| Integer32 as prtExTsPrtIdx | |||
| Integer32 as prtExTsIdx | |||
| Integer32 as prtExTsBit | |||
| INTEGER as prtExTsIConSlot | |||
| Integer32 as prtExTsIConPrt | |||
| INTEGER as prtExTsBitTest | |||
| OCTET STRING as prtExTsTxSignaling | |||
| OCTET STRING as prtExTsRxSignaling | |||
| PrtAgendaBehaviourEntry | |||
| SEQUENCE | |||
| Integer32 as prtAgendaBehaviourCnfgIdx | |||
| Integer32 as prtAgendaBehaviourSltIdx | |||
| Integer32 as prtAgendaBehaviourPrtIdx | |||
| INTEGER as prtAgendaBehaviourOnOff | |||
| PrtCnfgAgendaEntry | |||
| SEQUENCE | |||
| Integer32 as prtCnfgAgendaCnfgIdx | |||
| Integer32 as prtCnfgAgendaSltIdx | |||
| Integer32 as prtCnfgAgendaPrtIdx | |||
| INTEGER as prtCnfgAgendaDayIdx | |||
| Integer32 as prtCnfgAgendaSesId | |||
| Integer32 as prtCnfgAgendaFrom | |||
| Integer32 as prtCnfgAgendaTo | |||
| PrtGenCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtGenCnfgIdx | |||
| INTEGER as prtGenCnfgSltIdx | |||
| Integer32 as prtGenCnfgPrtIdx | |||
| INTEGER as prtGenCnfgLinkToSlot | |||
| Integer32 as prtGenCnfgLinkToPort | |||
| Integer32 as prtGenCnfgPortId | |||
| PrtCmprEntry | |||
| SEQUENCE | |||
| Integer32 as prtCmprTypIdx | |||
| Integer32 as prtCmprCnfgIdx | |||
| Integer32 as prtCmprVersion | |||
| INTEGER as prtCmprSltIdx | |||
| Integer32 as prtCmprPrtIdx | |||
| OCTET STRING as prtCmprObj | |||
| OCTET STRING as prtCmprStatisticObj | |||
| PrtDlciCmprEntry | |||
| SEQUENCE | |||
| Integer32 as prtDlciCmprCnfgIdx | |||
| Integer32 as prtDlciCmprVersion | |||
| INTEGER as prtDlciCmprSltIdx | |||
| INTEGER as prtDlciCmprPrtIdx | |||
| Integer32 as prtDlciCmprDlciIdx | |||
| OCTET STRING as prtDlciCmprObj | |||
| PrtAlarmsCmprEntry | |||
| SEQUENCE | |||
| Integer32 as prtAlarmsCmprVersion | |||
| Integer32 as prtAlarmsCmprAlarmSlot | |||
| Integer32 as prtAlarmsCmprAlarmPort | |||
| Integer32 as prtAlarmsCmprAlarmIdx | |||
| OCTET STRING as prtAlarmsCmprObj | |||
| PrtSExHsfStatEntry | |||
| SEQUENCE | |||
| INTEGER as prtSExHsfSltIdx | |||
| INTEGER as prtSExHsfPrtIdx | |||
| INTEGER as prtSExHsfInterfaceTyp | |||
| INTEGER as prtSExHsfRts | |||
| MdlPbxFramerCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as mdlPbxFraCnfgIdx | |||
| INTEGER as mdlPbxFraSltIdx | |||
| INTEGER as mdlPbxFraEnhEcho | |||
| INTEGER as mdlPbxFraTSGroupAss | |||
| INTEGER as mdlPbxFraSignalMode | |||
| OCTET STRING as mdlPbxFraSignalVector | |||
| OCTET STRING as mdlPbxFraSignalMask | |||
| INTEGER as mdlPbxFraFramerSlot | |||
| INTEGER as mdlPbxFraSignaling | |||
| Integer32 as mdlPbxFraTransSigTs | |||
| PrtExClCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExClCnfgIdx | |||
| INTEGER as prtExClSltIdx | |||
| INTEGER as prtExClPrtIdx | |||
| INTEGER as prtExClUsage | |||
| INTEGER as prtExClRate | |||
| INTEGER as prtExClDataBits | |||
| INTEGER as prtExClParity | |||
| INTEGER as prtExClStopBits | |||
| INTEGER as prtExClRoutingProtocol | |||
| INTEGER as prtExClEnabled | |||
| PrtExPh1MlCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPh1MlCnfgIdx | |||
| INTEGER as prtExPh1MlSltIdx | |||
| INTEGER as prtExPh1MlPrtIdx | |||
| INTEGER as prtExPh1MlConnect | |||
| INTEGER as prtExPh1MlLineType | |||
| INTEGER as prtExPh1MlLineCode | |||
| INTEGER as prtExPh1MlLineLen | |||
| INTEGER as prtExPh1MlRestoreTime | |||
| INTEGER as prtExPh1MlTxGain | |||
| INTEGER as prtExPh1MlRxSensitivity | |||
| Integer32 as prtExPh1MlIdleCode | |||
| INTEGER as prtExPh1MlTdmTrunk | |||
| INTEGER as prtExPh1MlClkMode | |||
| INTEGER as prtExPh1MlMfClkSrcSlt | |||
| INTEGER as prtExPh1MlMfClkSrcPrt | |||
| INTEGER as prtExPh1MlFdlType | |||
| INTEGER as prtExPh1MlInbandMng | |||
| INTEGER as prtExPh1MlInbandMngRate | |||
| INTEGER as prtExPh1MlRedundType | |||
| INTEGER as prtExPh1MlRedundSlot | |||
| INTEGER as prtExPh1MlRedundPort | |||
| Integer32 as prtExPh1MlRedundRecTime | |||
| INTEGER as prtExPh1MlInbandMngRoutProt | |||
| INTEGER as prtExPh1MlIfType | |||
| INTEGER as prtExPh1MlMultiplier | |||
| INTEGER as prtExPh1MlSupportedTS | |||
| PrtExPh1MlTsEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPh1MlTsCnfgIdx | |||
| INTEGER as prtExPh1MlTsSltIdx | |||
| INTEGER as prtExPh1MlTsPrtIdx | |||
| Integer32 as prtExPh1MlTsIdx | |||
| INTEGER as prtExPh1MlTsIConSlot | |||
| Integer32 as prtExPh1MlTsIConPrt | |||
| Integer32 as prtExPh1MlTsIConTs | |||
| OBJECT IDENTIFIER as prtExPh1MlTsExt | |||
| INTEGER as prtExPh1MlTsTest | |||
| INTEGER as prtExPh1MlTsType | |||
| INTEGER as prtExPh1MlTsBundle | |||
| Integer32 as prtExPh1MlTsTestDuration | |||
| PrtInPh1MlCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInPh1MlCnfgIdx | |||
| INTEGER as prtInPh1MlSltType | |||
| Integer32 as prtInPh1MlPrtIdx | |||
| INTEGER as prtInPh1MlConnect | |||
| INTEGER as prtInPh1MlRate | |||
| INTEGER as prtInPh1MlProtocol | |||
| INTEGER as prtInPh1MlConnectionTyp | |||
| INTEGER as prtInPh1MlCongResponse | |||
| Integer32 as prtInPh1MlCongLevel | |||
| INTEGER as prtInPh1MlTc | |||
| INTEGER as prtInPh1MlFlowControl | |||
| INTEGER as prtInPh1MlSegment | |||
| INTEGER as prtInPh1MlFrMngProt | |||
| Integer32 as prtInPh1MlEnqPeriod | |||
| Integer32 as prtInPh1MlFullRptPeriod | |||
| Integer32 as prtInPh1MlFrWindowSize | |||
| Integer32 as prtInPh1MlErrorsThreshold | |||
| Integer32 as prtInPh1MlMaxIdleTime | |||
| INTEGER as prtInPh1MlBearerCh | |||
| INTEGER as prtInPh1MlAssociatedExCh | |||
| INTEGER as prtInPh1MlClockEncoding | |||
| Integer32 as prtInPh1MlMinSeparators | |||
| INTEGER as prtInPh1MlCcittCrc | |||
| INTEGER as prtInPh1MlFrameSeparator | |||
| PrtInPh1MlDlciEntry | |||
| SEQUENCE | |||
| Integer32 as prtInPh1MlDlciCnfgIdx | |||
| INTEGER as prtInPh1MlDlciSltIdx | |||
| INTEGER as prtInPh1MlDlciPrtIdx | |||
| Integer32 as prtInPh1MlDlciIdx | |||
| INTEGER as prtInPh1MlDlciValid | |||
| INTEGER as prtInPh1MlDlciIConSlt | |||
| INTEGER as prtInPh1MlDlciIConPrt | |||
| Integer32 as prtInPh1MlDlciIConDlci | |||
| INTEGER as prtInPh1MlDlciTxBc | |||
| INTEGER as prtInPh1MlDlciTxBe | |||
| INTEGER as prtInPh1MlDlciRxBc | |||
| INTEGER as prtInPh1MlDlciRxBe | |||
| Integer32 as prtInPh1MlDlciPriority | |||
| INTEGER as prtInPh1MlDlciStatus | |||
| PrtPhMlCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtPhMlCnfgIdx | |||
| INTEGER as prtPhMlSltIdx | |||
| INTEGER as prtPhMlPrtIdx | |||
| INTEGER as prtPhMlConnect | |||
| INTEGER as prtPhMlRate | |||
| INTEGER as prtPhMlCAS | |||
| INTEGER as prtPhMlClockMode | |||
| INTEGER as prtPhMlSatBuffer | |||
| INTEGER as prtPhMlDialProcess | |||
| Integer32 as prtPhMlSyncRestore | |||
| INTEGER as prtPhMlBus | |||
| INTEGER as prtPhMlMfSyncSlot | |||
| PrtLogicalCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtLogicalCnfgIdx | |||
| INTEGER as prtLogicalSltIdx | |||
| Integer32 as prtLogicalPrtIdx | |||
| INTEGER as prtLogicalConnect | |||
| INTEGER as prtLogicalFunction | |||
| RowStatus as prtLogicalRowStatus | |||
| LinkSelectorCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as linkSelectorCnfgIdx | |||
| INTEGER as linkSelectorSltIdx | |||
| Integer32 as linkSelectorPrtIdx | |||
| Integer32 as linkSelectorMaxIdleTime | |||
| INTEGER as linkSelectorMode | |||
| INTEGER as linkSelectorRevert | |||
| Integer32 as linkSelectorMinBUSession | |||
| LinkSelectorPLinkEntry | |||
| SEQUENCE | |||
| Integer32 as pLinkCnfgIdx | |||
| INTEGER as pLinkSltIdx | |||
| Integer32 as pLinkPrtIdx | |||
| Integer32 as pLinkIdx | |||
| INTEGER as pLinkSlotNu | |||
| Integer32 as pLinkPortNu | |||
| Integer32 as pLinkPrioNu | |||
| INTEGER as pLinkVRate | |||
| PrtExPhPlCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPhPlCnfgIdx | |||
| INTEGER as prtExPhPlSltIdx | |||
| INTEGER as prtExPhPlPrtIdx | |||
| INTEGER as prtExPhPlConnect | |||
| INTEGER as prtExPhPlHRate | |||
| INTEGER as prtExPhPlLRate | |||
| INTEGER as prtExPhPlProtocol | |||
| INTEGER as prtExPhPlConnectionTyp | |||
| INTEGER as prtExPhPlClkMode | |||
| INTEGER as prtExPhPlDceClkSrc | |||
| INTEGER as prtExPhPlCongResponse | |||
| Integer32 as prtExPhPlCongLevel | |||
| INTEGER as prtExPhPlTc | |||
| INTEGER as prtExPhPlFlowControl | |||
| INTEGER as prtExPhPlDcdRts | |||
| INTEGER as prtExPhPlDcdRtsControlPath | |||
| INTEGER as prtExPhPlDataBits | |||
| INTEGER as prtExPhPlParity | |||
| INTEGER as prtExPhPlStopBits | |||
| Integer32 as prtExPhPlLXon | |||
| Integer32 as prtExPhPlLXoff | |||
| INTEGER as prtExPhPlFrMngProt | |||
| Integer32 as prtExPhPlEnqPeriod | |||
| Integer32 as prtExPhPlFullRptPeriod | |||
| Integer32 as prtExPhPlFrWindowSize | |||
| Integer32 as prtExPhPlErrorsThreshold | |||
| INTEGER as prtExPhPlPvcCreateMsg | |||
| INTEGER as prtExPhPlCllmMsg | |||
| INTEGER as prtExPhPlProtDelayLevel | |||
| INTEGER as prtExPhPlClockEncoding | |||
| Integer32 as prtExPhPlMinSeparators | |||
| INTEGER as prtExPhPlCcittCrc | |||
| INTEGER as prtExPhPlFrameSeparator | |||
| Integer32 as prtExPhPlIdleCode | |||
| Integer32 as prtExPhPlJitter | |||
| PrtExPhPlDlciEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPhPlDlciCnfgIdx | |||
| INTEGER as prtExPhPlDlciSltIdx | |||
| INTEGER as prtExPhPlDlciPrtIdx | |||
| Integer32 as prtExPhPlDlciIdx | |||
| INTEGER as prtExPhPlDlciValid | |||
| INTEGER as prtExPhPlDlciIConSlt | |||
| INTEGER as prtExPhPlDlciIConPrt | |||
| Integer32 as prtExPhPlDlciIConDlci | |||
| INTEGER as prtExPhPlDlciTxBc | |||
| INTEGER as prtExPhPlDlciTxBe | |||
| INTEGER as prtExPhPlDlciRxBc | |||
| INTEGER as prtExPhPlDlciRxBe | |||
| Integer32 as prtExPhPlDlciPriority | |||
| INTEGER as prtExPhPlDlciStatus | |||
| PrtExPhPlModemEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPhPlModemCnfgIdx | |||
| INTEGER as prtExPhPlModemSltIdx | |||
| INTEGER as prtExPhPlModemPrtIdx | |||
| INTEGER as prtExPhPlModemStatus | |||
| INTEGER as prtExPhPlModemActivate | |||
| Integer32 as prtExPhPlModemMaxIdleTime | |||
| Integer32 as prtExPhPlModemTimeBtwnCalls | |||
| Integer32 as prtExPhPlModemCallDelay | |||
| PrtExLs2CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExLs2CnfgIdx | |||
| INTEGER as prtExLs2SltIdx | |||
| INTEGER as prtExLs2PrtIdx | |||
| INTEGER as prtExLs2Connect | |||
| INTEGER as prtExLs2Rate | |||
| INTEGER as prtExLs2ClkMode | |||
| INTEGER as prtExLs2Cts | |||
| INTEGER as prtExLs2Dcd | |||
| Integer32 as prtExLs2EnvIdx | |||
| PrtInLs2CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInLs2CnfgIdx | |||
| INTEGER as prtInLs2SltIdx | |||
| INTEGER as prtInLs2PrtIdx | |||
| INTEGER as prtInLs2Connect | |||
| Integer32 as prtInLs2Group | |||
| Integer32 as prtInLs2Member | |||
| INTEGER as prtInLs2LinkTo | |||
| INTEGER as prtInLs2EnvAssign | |||
| PrtVc2CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtVc2CnfgIdx | |||
| INTEGER as prtVc2SltIdx | |||
| Integer32 as prtVc2PrtIdx | |||
| INTEGER as prtExVc2Connect | |||
| Integer32 as prtExVc2TransGain | |||
| Integer32 as prtExVc2ReceiveGain | |||
| INTEGER as prtExVc2Wire | |||
| INTEGER as prtExVc2CodingLaw | |||
| INTEGER as prtExVc2Sig | |||
| INTEGER as prtExVc2Oos | |||
| INTEGER as prtExVc2LinkTo | |||
| INTEGER as prtExVc2OperMode | |||
| INTEGER as prtExVc2SigProfile | |||
| INTEGER as prtExVc2CallEnable | |||
| INTEGER as prtExVc2R2Delay | |||
| INTEGER as prtExVc2CasStd | |||
| INTEGER as prtExVc2EchoCanceler | |||
| INTEGER as prtExVc2IfType | |||
| INTEGER as prtExVc2Encoding | |||
| OCTET STRING as prtExVc2TxBitCode | |||
| OCTET STRING as prtExVc2RxBitOutput | |||
| INTEGER as prtExVc2MeterRate | |||
| INTEGER as prtExVc2IfSignaling | |||
| INTEGER as prtExVc2SeizeAck | |||
| INTEGER as prtExVc2EandMType | |||
| INTEGER as prtExVc2RemType | |||
| INTEGER as prtExVc2ConvTime | |||
| INTEGER as prtExVc2SigFeedback | |||
| INTEGER as prtExVc2EchoCancelerModule | |||
| PrtHsfCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtHsfCnfgIdx | |||
| INTEGER as prtHsfSltIdx | |||
| INTEGER as prtHsfPrtIdx | |||
| INTEGER as prtExHsfConnect | |||
| INTEGER as prtExHsfRate | |||
| INTEGER as prtExHsfClkMode | |||
| INTEGER as prtExHsfCts | |||
| INTEGER as prtExHsfFifoSize | |||
| INTEGER as prtExHsfLinkTo | |||
| INTEGER as prtExHsfOperMode | |||
| INTEGER as prtExHsfInbandLoopback | |||
| INTEGER as prtExHsfClkPolarity | |||
| INTEGER as prtExHsfControlSignal | |||
| PrtExHs4CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExHs4CnfgIdx | |||
| INTEGER as prtExHs4SltIdx | |||
| INTEGER as prtExHs4PrtIdx | |||
| INTEGER as prtExHs4Connect | |||
| INTEGER as prtExHs4LineType | |||
| INTEGER as prtExHs4LineCode | |||
| INTEGER as prtExHs4LineLen | |||
| INTEGER as prtExHs4RestoreT | |||
| INTEGER as prtExHs4OosSig | |||
| INTEGER as prtExHs4OosCode | |||
| Integer32 as prtExHs4IdleCode | |||
| INTEGER as prtExHs4MfClkSrcSlt | |||
| INTEGER as prtExHs4MfClkSrcPrt | |||
| PrtExHs4TsEntry | |||
| SEQUENCE | |||
| Integer32 as prtExHs4TsCnfgIdx | |||
| INTEGER as prtExHs4TsSltIdx | |||
| INTEGER as prtExHs4TsPrtIdx | |||
| Integer32 as prtExHs4TsIdx | |||
| INTEGER as prtExHs4TsIConSlot | |||
| INTEGER as prtExHs4TsIConPrt | |||
| Integer32 as prtExHs4TsIConTs | |||
| PrtExHsiCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExHsiCnfgIdx | |||
| INTEGER as prtExHsiSltIdx | |||
| Integer32 as prtExHsiPrtIdx | |||
| INTEGER as prtExHsiConnect | |||
| INTEGER as prtExHsiRate | |||
| INTEGER as prtExHsiLinkTo | |||
| INTEGER as prtExHsiInterface | |||
| INTEGER as prtExHsiActType | |||
| PrtInHsiCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInHsiCnfgIdx | |||
| INTEGER as prtInHsiSltIdx | |||
| Integer32 as prtInHsiPrtIdx | |||
| INTEGER as prtInHsiConnect | |||
| INTEGER as prtInHsiRate | |||
| Integer32 as prtInHsiConcentratedTo | |||
| PrtExHsrCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExHsrCnfgIdx | |||
| INTEGER as prtExHsrSltIdx | |||
| Integer32 as prtExHsrPrtIdx | |||
| INTEGER as prtExHsrConnect | |||
| INTEGER as prtExHsrProtocol | |||
| INTEGER as prtExHsrRate | |||
| INTEGER as prtExHsrDataBits | |||
| INTEGER as prtExHsrParity | |||
| INTEGER as prtExHsrStopBits | |||
| INTEGER as prtExHsrCts | |||
| INTEGER as prtExHsrClkMode | |||
| INTEGER as prtExHsrLinkTo | |||
| INTEGER as prtExHsrDcdDsr | |||
| INTEGER as prtExHsrOperMode | |||
| INTEGER as prtExHsrRtsDtr | |||
| INTEGER as prtExHsrLlbEnable | |||
| INTEGER as prtExHsrRlbEnable | |||
| INTEGER as prtExHsrRateAdapt | |||
| INTEGER as prtExHsrRemoteModem | |||
| PrtExMbeCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExMbeCnfgIdx | |||
| INTEGER as prtExMbeSltIdx | |||
| INTEGER as prtExMbePrtIdx | |||
| INTEGER as prtExMbeLan | |||
| PrtInMbeCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInMbeCnfgIdx | |||
| INTEGER as prtInMbeSltIdx | |||
| INTEGER as prtInMbePrtIdx | |||
| INTEGER as prtInMbeConnect | |||
| INTEGER as prtInMbeRate | |||
| INTEGER as prtInMbeLinkTo | |||
| PrtExTreCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExTreCnfgIdx | |||
| INTEGER as prtExTreSltIdx | |||
| INTEGER as prtExTrePrtIdx | |||
| INTEGER as prtExTreLan | |||
| INTEGER as prtExTreLanRate | |||
| PrtInTreCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInTreCnfgIdx | |||
| INTEGER as prtInTreSltIdx | |||
| INTEGER as prtInTrePrtIdx | |||
| INTEGER as prtInTreConnect | |||
| INTEGER as prtInTreRate | |||
| INTEGER as prtInTreLinkTo | |||
| PrtExPVc4CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPVc4CnfgIdx | |||
| INTEGER as prtExPVc4SltIdx | |||
| INTEGER as prtExPVc4PrtIdx | |||
| INTEGER as prtExPVc4PrtType | |||
| INTEGER as prtExPVc4Connect | |||
| INTEGER as prtExPVc4IfType | |||
| Integer32 as prtExPVc4TxGain | |||
| Integer32 as prtExPVc4RxGain | |||
| INTEGER as prtExPVc4MaxRate | |||
| INTEGER as prtExPVc4Tc | |||
| INTEGER as prtExPVc4Oos | |||
| INTEGER as prtExPVc4EchoCanceler | |||
| Integer32 as prtExPVc4VarDelay | |||
| Integer32 as prtExPVc4CongLevel | |||
| INTEGER as prtExPVc4Wire | |||
| INTEGER as prtExPVc4ExtensionType | |||
| DisplayString as prtExPVc4ExtensionNumber | |||
| INTEGER as prtExPVc4OutPulsing | |||
| INTEGER as prtExPVc4HuntGroupMb | |||
| Integer32 as prtExPVc4HuntGroupIdx | |||
| INTEGER as prtExPVc4AutoFaxMode | |||
| INTEGER as prtExPVc4FaxRate | |||
| INTEGER as prtExPVc4SeizeAck | |||
| INTEGER as prtExPVc4SignalingProtocol | |||
| Integer32 as prtExPVc4DelayStart | |||
| Integer32 as prtExPVc4WinkMinDuration | |||
| Integer32 as prtExPVc4WinkMaxDuration | |||
| INTEGER as prtExPVc4GenerateTone | |||
| INTEGER as prtExPVc4CodingLaw | |||
| INTEGER as prtExPVc4GenerateRingBack | |||
| Integer32 as prtExPVc4ChannelId | |||
| INTEGER as prtExPVc4PortConnection | |||
| INTEGER as prtExPVc4CoderAndRate | |||
| DisplayString as prtExPVc4DestinationNum | |||
| INTEGER as prtExPVc4DtmfRelay | |||
| Integer32 as prtExPVc4DiscOnSilence | |||
| INTEGER as prtExPVc4DynamicJitter | |||
| INTEGER as prtExPVc4EandMType | |||
| PrtExPVc4DlciEntry | |||
| SEQUENCE | |||
| Integer32 as prtExPVc4DlciCnfgIdx | |||
| INTEGER as prtExPVc4DlciSltIdx | |||
| INTEGER as prtExPVc4DlciPrtIdx | |||
| INTEGER as prtExPVc4DlciValid | |||
| INTEGER as prtExPVc4DlciIConSlt | |||
| INTEGER as prtExPVc4DlciIConPrt | |||
| Integer32 as prtExPVc4DlciIConDlci | |||
| INTEGER as prtExPVc4DlciTxBc | |||
| INTEGER as prtExPVc4DlciTxBe | |||
| INTEGER as prtExPVc4DlciRxBc | |||
| INTEGER as prtExPVc4DlciRxBe | |||
| Integer32 as prtExPVc4DlciPriority | |||
| INTEGER as prtExPVc4DlciStatus | |||
| PrtExLs6CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExLs6CnfgIdx | |||
| INTEGER as prtExLs6SltIdx | |||
| INTEGER as prtExLs6PrtIdx | |||
| INTEGER as prtExLs6Connect | |||
| INTEGER as prtExLs6Protocol | |||
| INTEGER as prtExLs6Rate | |||
| INTEGER as prtExLs6ClkMode | |||
| INTEGER as prtExLs6CtrlSignal | |||
| INTEGER as prtExLs6DataBits | |||
| INTEGER as prtExLs6Cts | |||
| INTEGER as prtExLs6LinkToInternal | |||
| PrtExLs6VCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExLs6VCnfgIdx | |||
| INTEGER as prtExLs6VSltIdx | |||
| INTEGER as prtExLs6VPrtIdx | |||
| INTEGER as prtExLs6VConnect | |||
| INTEGER as prtExLs6VRate | |||
| INTEGER as prtExLs6VEchoCanceler | |||
| INTEGER as prtExLs6VIfType | |||
| Integer32 as prtExLs6VTxGain | |||
| Integer32 as prtExLs6VRxGain | |||
| INTEGER as prtExLs6VOos | |||
| PrtInLs6CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInLs6CnfgIdx | |||
| INTEGER as prtInLs6SltIdx | |||
| INTEGER as prtInLs6PrtIdx | |||
| INTEGER as prtInLs6Connect | |||
| INTEGER as prtInLs6TandemMode | |||
| INTEGER as prtInLs6Rate | |||
| INTEGER as prtInLs6RemoteType | |||
| INTEGER as prtInLs6LinkTo | |||
| PrtExVc3CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExVc3CnfgIdx | |||
| INTEGER as prtExVc3SltIdx | |||
| INTEGER as prtExVc3PrtIdx | |||
| INTEGER as prtExVc3Connect | |||
| Integer32 as prtExVc3TransGain | |||
| Integer32 as prtExVc3ReceiveGain | |||
| INTEGER as prtExVc3Wire | |||
| INTEGER as prtExVc3Rate | |||
| INTEGER as prtExVc3EchoCanceler | |||
| PrtInVc3CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtInVc3CnfgIdx | |||
| INTEGER as prtInVc3SltIdx | |||
| INTEGER as prtInVc3PrtIdx | |||
| INTEGER as prtInVc3Connect | |||
| INTEGER as prtInVc3Rate | |||
| INTEGER as prtInVc3Oos | |||
| INTEGER as prtInVc3LinkTo | |||
| PrtExVcPbxCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtExVcPbxCnfgIdx | |||
| INTEGER as prtExVcPbxSltIdx | |||
| INTEGER as prtExVcPbxPrtIdx | |||
| INTEGER as prtExVcPbxConnect | |||
| INTEGER as prtExVcPbxGroup | |||
| INTEGER as prtExVcPbxTransparent | |||
| Integer32 as prtExVcPbxTransSignalTs | |||
| INTEGER as prtExVcPbxFrame | |||
| INTEGER as prtExVcPbxRestoreTime | |||
| INTEGER as prtExVcPbxLineCode | |||
| INTEGER as prtExVcPbxLineLength | |||
| INTEGER as prtExVcPbxLinkTo | |||
| INTEGER as prtExVcPbxSignalOper | |||
| INTEGER as prtExVcPbxIdleCode | |||
| PrtIn1p6VcPbxCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtIn1p6VcPbxCnfgIdx | |||
| INTEGER as prtIn1p6VcPbxSltIdx | |||
| INTEGER as prtIn1p6VcPbxPrtIdx | |||
| INTEGER as prtIn1p6VcPbxConnect | |||
| INTEGER as prtIn1p6VcPbxRate | |||
| INTEGER as prtIn1p6VcPbxEchoCanceler | |||
| Integer32 as prtIn1p6VcPbxPabxTs | |||
| PrtIn7p8VcPbxCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtIn7p8VcPbxCnfgIdx | |||
| INTEGER as prtIn7p8VcPbxSltIdx | |||
| INTEGER as prtIn7p8VcPbxPrtIdx | |||
| INTEGER as prtIn7p8VcPbxConnect | |||
| INTEGER as prtIn7p8VcPbxMode | |||
| INTEGER as prtIn7p8VcPbxRate | |||
| INTEGER as prtIn7p8VcPbxSignalMode | |||
| INTEGER as prtIn7p8VcPbxOos | |||
| INTEGER as prtIn7p8VcPbxLinkTo | |||
| PrtExVcPbxTsEntry | |||
| SEQUENCE | |||
| Integer32 as prtExVcPbxTsCnfgIdx | |||
| INTEGER as prtExVcPbxTsSltIdx | |||
| INTEGER as prtExVcPbxTsPrtIdx | |||
| Integer32 as prtExVcPbxTsIdx | |||
| INTEGER as prtExVcPbxTsMode | |||
| INTEGER as prtExVcPbxTsIConSlot | |||
| INTEGER as prtExVcPbxTsIConPrt | |||
| PrtIsdnCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtIsdnCnfgIdx | |||
| INTEGER as prtIsdnSltIdx | |||
| Integer32 as prtIsdnPrtIdx | |||
| INTEGER as prtIsdnConnect | |||
| INTEGER as prtIsdnSignalingProtocol | |||
| INTEGER as prtIsdnBasicRateLineTopology | |||
| INTEGER as prtIsdnMode | |||
| INTEGER as prtIsdnFilter | |||
| INTEGER as prtIsdnSimultaneousCall | |||
| Integer32 as prtIsdnNumOfAbstractTerm | |||
| INTEGER as prtIsdnSwitchMode | |||
| INTEGER as prtIsdnAbSide | |||
| INTEGER as prtIsdnQsigRole | |||
| INTEGER as prtIsdnInterface | |||
| INTEGER as prtIsdnCallMode | |||
| INTEGER as prtIsdnCallBackTimeout | |||
| PrtIsdnEndpointEntry | |||
| SEQUENCE | |||
| Integer32 as prtIsdnEndpointCnfgIdx | |||
| INTEGER as prtIsdnEndpointSltIdx | |||
| Integer32 as prtIsdnEndpointPrtIdx | |||
| INTEGER as prtIsdnEndpointIdx | |||
| INTEGER as prtIsdnEndpointTeiType | |||
| Integer32 as prtIsdnEndpointTeiValue | |||
| DisplayString as prtIsdnEndpointSpid | |||
| INTEGER as prtIsdnEndpointBearerCh | |||
| RowStatus as prtIsdnEndpointRowStatus | |||
| PrtIsdnDirectoryEntry | |||
| SEQUENCE | |||
| Integer32 as prtIsdnDirectoryCnfgIdx | |||
| INTEGER as prtIsdnDirectorySltIdx | |||
| Integer32 as prtIsdnDirectoryPrtIdx | |||
| DisplayString as prtIsdnDirectoryLocalAddr | |||
| DisplayString as prtIsdnDirectoryLocalSubAddr | |||
| DisplayString as prtIsdnDirectoryRemoteAddr | |||
| DisplayString as prtIsdnDirectoryRemoteSubAddr | |||
| Integer32 as prtIsdnDirectoryPrtNu | |||
| Integer32 as prtIsdnDirectoryTeiId | |||
| RowStatus as prtIsdnDirectoryRowStatus | |||
| DisplayString as prtIsdnDirectoryLocalAddr2 | |||
| DisplayString as prtIsdnDirectoryLocalSubAddr2 | |||
| DisplayString as prtIsdnDirectoryRemoteAddr2 | |||
| DisplayString as prtIsdnDirectoryRemoteSubAddr2 | |||
| PrtFrPlusCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtFrPlusCnfgIdx | |||
| INTEGER as prtFrPlusSltIdx | |||
| Integer32 as prtFrPlusPrtIdx | |||
| OCTET STRING as prtFrPlusNotSegmentedPriorities | |||
| PrtMl4CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtMl4CnfgIdx | |||
| INTEGER as prtMl4SltIdx | |||
| INTEGER as prtMl4PrtIdx | |||
| INTEGER as prtMl4SigProfile | |||
| INTEGER as prtMl4CGA | |||
| INTEGER as prtMl4Oos | |||
| OCTET STRING as prtMl4VoiceOos | |||
| OCTET STRING as prtMl4DataOos | |||
| INTEGER as prtMl4Service | |||
| IpAddress as prtMl4IpAddress | |||
| IpAddress as prtMl4IpMask | |||
| INTEGER as prtMl4SignalingMode | |||
| INTEGER as prtMl4EchoCanceler | |||
| INTEGER as prtMl4OosErrorSource | |||
| Integer32 as prtMl4OosEntryThreshold | |||
| Integer32 as prtMl4OosExitThreshold | |||
| PrtAcmCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtAcmCnfgIdx | |||
| INTEGER as prtAcmSltIdx | |||
| INTEGER as prtAcmPrtIdx | |||
| INTEGER as prtAcmConnect | |||
| INTEGER as prtAcmActiveState | |||
| DisplayString as prtAcmAlrString | |||
| PrtE2CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtE2CnfgIdx | |||
| INTEGER as prtE2SltIdx | |||
| INTEGER as prtE2PrtIdx | |||
| INTEGER as prtE2Connect | |||
| INTEGER as prtE2MngOnNationalBit | |||
| EthIfEntry | |||
| SEQUENCE | |||
| Integer32 as ethIfIdx | |||
| INTEGER as ethMode | |||
| INTEGER as ethBridgingMode | |||
| INTEGER as ethEncapsulationCRCMode | |||
| INTEGER as ethBackPressure | |||
| INTEGER as ethLimit4 | |||
| INTEGER as ethSkipInitReset | |||
| INTEGER as ethMulticastBlock | |||
| INTEGER as ethBroadcastBlock | |||
| INTEGER as ethSpeed | |||
| EthIfCurrentEntry | |||
| SEQUENCE | |||
| Integer32 as ethIfCurrentIndex | |||
| OCTET STRING as ethIfCurrentStatus | |||
| Gauge32 as ethIfCurrentInFrames | |||
| Gauge32 as ethIfCurrentInOctets | |||
| Gauge32 as ethIfCurrentAlignmentErrors | |||
| Gauge32 as ethIfCurrentFCSErrors | |||
| Gauge32 as ethIfCurrentLengthError | |||
| Gauge32 as ethIfCurrentOutFrames | |||
| Gauge32 as ethIfCurrentOutOctets | |||
| Gauge32 as ethIfCurrentSingleCollisionFrames | |||
| Gauge32 as ethIfCurrentMultipleCollisionFrames | |||
| Gauge32 as ethIfCurrentDeferredTransmissions | |||
| Gauge32 as ethIfCurrentLateCollisions | |||
| Gauge32 as ethIfCurrentCarrierSenseErrors | |||
| EthIfIntervalEntry | |||
| SEQUENCE | |||
| Integer32 as ethIfIntervalIndex | |||
| Integer32 as ethIfIntervalNumber | |||
| OCTET STRING as ethIfIntervalStatus | |||
| Gauge32 as ethIfIntervalInFrames | |||
| Gauge32 as ethIfIntervalInOctets | |||
| Gauge32 as ethIfIntervalAlignmentErrors | |||
| Gauge32 as ethIfIntervalFCSErrors | |||
| Gauge32 as ethIfIntervalLengthError | |||
| Gauge32 as ethIfIntervalOutFrames | |||
| Gauge32 as ethIfIntervalOutOctets | |||
| Gauge32 as ethIfIntervalSingleCollisionFrames | |||
| Gauge32 as ethIfIntervalMultipleCollisionFrames | |||
| Gauge32 as ethIfIntervalDeferredTransmissions | |||
| Gauge32 as ethIfIntervalLateCollisions | |||
| Gauge32 as ethIfIntervalCarrierSenseErrors | |||
| AgnTsEntry | |||
| SEQUENCE | |||
| Integer32 as agnTsCnfgIdx | |||
| INTEGER as agnTsSltIdx | |||
| Integer32 as agnTsPrtIdx | |||
| Integer32 as agnTsIdx | |||
| Integer32 as agnTsBitIdx | |||
| INTEGER as agnTsConSltIdx | |||
| Integer32 as agnTsConPrtIdx | |||
| Integer32 as agnTsConIdx | |||
| INTEGER as agnTsType | |||
| RowStatus as agnTsRowStatus | |||
| INTEGER as agnTsDirection | |||
| PktSwchRoutSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchRoutIdS | |||
| DisplayString as pktSwchRoutAddressS | |||
| DisplayString as pktSwchRoutDestLink1S | |||
| DisplayString as pktSwchRoutDestLink2S | |||
| DisplayString as pktSwchRoutDestLink3S | |||
| Integer32 as pktSwchRoutLinkPrio1S | |||
| Integer32 as pktSwchRoutLinkPrio2S | |||
| Integer32 as pktSwchRoutLinkPrio3S | |||
| INTEGER as pktSwchRoutSearchStatusS | |||
| INTEGER as pktSwchRoutStatusS | |||
| PktSwchRoutAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchRoutIdA | |||
| DisplayString as pktSwchRoutAddressA | |||
| DisplayString as pktSwchRoutDestLink1A | |||
| DisplayString as pktSwchRoutDestLink2A | |||
| DisplayString as pktSwchRoutDestLink3A | |||
| Integer32 as pktSwchRoutLinkPrio1A | |||
| Integer32 as pktSwchRoutLinkPrio2A | |||
| Integer32 as pktSwchRoutLinkPrio3A | |||
| INTEGER as pktSwchRoutSearchStatusA | |||
| PktSwchPvcSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPvcNumS | |||
| Integer32 as pktSwchPvcSrcLinkS | |||
| DisplayString as pktSwchPvcSrcLcnS | |||
| Integer32 as pktSwchPvcDstLinkS | |||
| Integer32 as pktSwchPvcDstLcnS | |||
| INTEGER as pktSwchPvcStatusS | |||
| PktSwchPvcAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPvcNumA | |||
| Integer32 as pktSwchPvcSrcLinkA | |||
| DisplayString as pktSwchPvcSrcLcnA | |||
| Integer32 as pktSwchPvcDstLinkA | |||
| Integer32 as pktSwchPvcDstLcnA | |||
| PktSwchNuiSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiIndexS | |||
| Integer32 as pktSwchNuiGroupIdS | |||
| DisplayString as pktSwchNuiInPasswdS | |||
| Integer32 as pktSwchNuiOutPasswdPointerS | |||
| DisplayString as pktSwchNuiInAddrS | |||
| Integer32 as pktSwchNuiOutAddrPointerS | |||
| INTEGER as pktSwchNuiStatusS | |||
| PktSwchNuiAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiIndexA | |||
| Integer32 as pktSwchNuiGroupIdA | |||
| DisplayString as pktSwchNuiInPasswdA | |||
| Integer32 as pktSwchNuiOutPasswdPointerA | |||
| DisplayString as pktSwchNuiInAddrA | |||
| Integer32 as pktSwchNuiOutAddrPointerA | |||
| INTEGER as pktSwchNuiStatusA | |||
| PktSwchNuiOutPasswdSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiOutPasswdIndexS | |||
| DisplayString as pktSwchNuiOutPasswdValueS | |||
| INTEGER as pktSwchNuiOutPasswdStatusS | |||
| PktSwchNuiOutPasswdAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiOutPasswdIndexA | |||
| DisplayString as pktSwchNuiOutPasswdValueA | |||
| INTEGER as pktSwchNuiOutPasswdStatusA | |||
| PktSwchNuiOutAddrSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiOutAddrIndexS | |||
| DisplayString as pktSwchNuiOutAddrValueS | |||
| INTEGER as pktSwchNuiOutAddrStatusS | |||
| PktSwchNuiOutAddrAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchNuiOutAddrIndexA | |||
| DisplayString as pktSwchNuiOutAddrValueA | |||
| INTEGER as pktSwchNuiOutAddrStatusA | |||
| PktSwchMngX25Entry | |||
| SEQUENCE | |||
| Integer32 as pktSwchMngID | |||
| IpAddress as pktSwchMngIP | |||
| DisplayString as pktSwchMngPhyAddr | |||
| Integer32 as pktSwchTrapEnable | |||
| INTEGER as pktSwchEncapsulationMode | |||
| PktSwchXidSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchXidIndexS | |||
| Integer32 as pktSwchXidInternalIndexS | |||
| DisplayString as pktSwchXidPasswdS | |||
| DisplayString as pktSwchXidPhoneS | |||
| INTEGER as pktSwchXidStatusS | |||
| PktSwchXidAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchXidIndexA | |||
| Integer32 as pktSwchXidInternalIndexA | |||
| DisplayString as pktSwchXidPasswdA | |||
| DisplayString as pktSwchXidPhoneA | |||
| INTEGER as pktSwchXidStatusA | |||
| PktSwchIpRoutSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIpRoutIdS | |||
| IpAddress as pktSwchIpRoutIpAddressS | |||
| IpAddress as pktSwchIpRoutIpMaskS | |||
| INTEGER as pktSwchIpRoutDestProtocolS | |||
| DisplayString as pktSwchIpRoutDestinationS | |||
| Integer32 as pktSwchIpRoutInactivityS | |||
| INTEGER as pktSwchIpRoutStatusS | |||
| Integer32 as pktSwchIpRoutMetricS | |||
| IpAddress as pktSwchIpRoutNextHopS | |||
| Integer32 as pktSwchIpRoutInterfaceIdS | |||
| PktSwchIpRoutAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIpRoutIdA | |||
| IpAddress as pktSwchIpRoutIpAddressA | |||
| IpAddress as pktSwchIpRoutIpMaskA | |||
| INTEGER as pktSwchIpRoutDestProtocolA | |||
| DisplayString as pktSwchIpRoutDestinationA | |||
| Integer32 as pktSwchIpRoutInactivityA | |||
| Counter32 as pktSwchIpRoutBuffsInA | |||
| Counter32 as pktSwchIpRoutBuffsOutA | |||
| INTEGER as pktSwchIpRoutFCA | |||
| Integer32 as pktSwchIpRoutMetricA | |||
| IpAddress as pktSwchIpRoutNextHopA | |||
| Integer32 as pktSwchIpRoutInterfaceIdA | |||
| PktSwchTxPriorityEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchTxPriorityLevel | |||
| Integer32 as pktSwchTxPriorityMaxDelayTime | |||
| Integer32 as pktSwchTxPriorityMaxQueueLen | |||
| PktSwchProfileSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchProfileNumberS | |||
| Integer32 as pktSwchProfileRecallCharS | |||
| INTEGER as pktSwchProfileEchoS | |||
| Integer32 as pktSwchProfileDataForwCharS | |||
| Integer32 as pktSwchProfileIdleTimerS | |||
| INTEGER as pktSwchProfileDevFlowContS | |||
| INTEGER as pktSwchProfileServSigS | |||
| Integer32 as pktSwchProfileBreakS | |||
| INTEGER as pktSwchProfileDiscOutS | |||
| Integer32 as pktSwchProfileCRPaddingS | |||
| Integer32 as pktSwchProfileLineFoldS | |||
| INTEGER as pktSwchProfileSpeedS | |||
| INTEGER as pktSwchProfilePadFlowContS | |||
| INTEGER as pktSwchProfileLineFeedInsertS | |||
| Integer32 as pktSwchProfileLineFeedPadS | |||
| INTEGER as pktSwchProfileEditingS | |||
| Integer32 as pktSwchProfileCharDelS | |||
| Integer32 as pktSwchProfileLineDelS | |||
| Integer32 as pktSwchProfileLineDispS | |||
| Integer32 as pktSwchProfileEditServSigS | |||
| Integer32 as pktSwchProfileEchomaskS | |||
| INTEGER as pktSwchProfileParTreatS | |||
| Integer32 as pktSwchProfilePageWaitS | |||
| Integer32 as pktSwchProfileBitsPerCharS | |||
| INTEGER as pktSwchProfileDvParityS | |||
| INTEGER as pktSwchProfileStopBitsS | |||
| INTEGER as pktSwchProfileSpecFlowS | |||
| Integer32 as pktSwchProfileCountFwdS | |||
| Integer32 as pktSwchProfileEscDelayS | |||
| Integer32 as pktSwchProfileCharBreakS | |||
| Integer32 as pktSwchProfileCharSuppressS | |||
| Integer32 as pktSwchProfileCharSubsS | |||
| Integer32 as pktSwchProfileFormFeedPadS | |||
| Integer32 as pktSwchProfileInactivityS | |||
| Integer32 as pktSwchProfileOptionsS | |||
| Integer32 as pktSwchProfileClrTimerS | |||
| Integer32 as pktSwchProfileSubAddInCUDS | |||
| INTEGER as pktSwchProfileStatusS | |||
| PktSwchProfileAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchProfileNumberA | |||
| Integer32 as pktSwchProfileRecallCharA | |||
| INTEGER as pktSwchProfileEchoA | |||
| Integer32 as pktSwchProfileDataForwCharA | |||
| Integer32 as pktSwchProfileIdleTimerA | |||
| INTEGER as pktSwchProfileDevFlowContA | |||
| INTEGER as pktSwchProfileServSigA | |||
| Integer32 as pktSwchProfileBreakA | |||
| INTEGER as pktSwchProfileDiscOutA | |||
| Integer32 as pktSwchProfileCRPaddingA | |||
| Integer32 as pktSwchProfileLineFoldA | |||
| INTEGER as pktSwchProfileSpeedA | |||
| INTEGER as pktSwchProfilePadFlowContA | |||
| INTEGER as pktSwchProfileLineFeedInsertA | |||
| Integer32 as pktSwchProfileLineFeedPadA | |||
| INTEGER as pktSwchProfileEditingA | |||
| Integer32 as pktSwchProfileCharDelA | |||
| Integer32 as pktSwchProfileLineDelA | |||
| Integer32 as pktSwchProfileLineDispA | |||
| Integer32 as pktSwchProfileEditServSigA | |||
| Integer32 as pktSwchProfileEchomaskA | |||
| INTEGER as pktSwchProfileParTreatA | |||
| Integer32 as pktSwchProfilePageWaitA | |||
| Integer32 as pktSwchProfileBitsPerCharA | |||
| INTEGER as pktSwchProfileDvParityA | |||
| INTEGER as pktSwchProfileStopBitsA | |||
| INTEGER as pktSwchProfileSpecFlowA | |||
| Integer32 as pktSwchProfileCountFwdA | |||
| Integer32 as pktSwchProfileEscDelayA | |||
| Integer32 as pktSwchProfileCharBreakA | |||
| Integer32 as pktSwchProfileCharSuppressA | |||
| Integer32 as pktSwchProfileCharSubsA | |||
| Integer32 as pktSwchProfileFormFeedPadA | |||
| Integer32 as pktSwchProfileInactivityA | |||
| Integer32 as pktSwchProfileOptionsA | |||
| Integer32 as pktSwchProfileClrTimerA | |||
| Integer32 as pktSwchProfileSubAddInCUDA | |||
| PktSwchChannelSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchChannelIfIndexS | |||
| Integer32 as pktSwchChannelNumberS | |||
| Integer32 as pktSwchChannelProfileS | |||
| Integer32 as pktSwchChannelOutCallProfileS | |||
| Integer32 as pktSwchChannelInCallProfileS | |||
| Integer32 as pktSwchChannelRemoteProfileS | |||
| Integer32 as pktSwchChannelAutocallIdS | |||
| Integer32 as pktSwchChannelAlterAutocallIdS | |||
| Integer32 as pktSwchChannelAutocallRetriesS | |||
| Integer32 as pktSwchChannelAutocallIntervalS | |||
| Integer32 as pktSwchChannelCallAliasS | |||
| Integer32 as pktSwchChannelSubAddress1S | |||
| Integer32 as pktSwchChannelSubAddress2S | |||
| Integer32 as pktSwchChannelNUISEntry | |||
| Integer32 as pktSwchChannelClearTimerS | |||
| Integer32 as pktSwchChannelOptionsS | |||
| INTEGER as pktSwchChannelClear | |||
| Integer32 as pktSwchChannelCopyTo | |||
| Integer32 as pktSwchChannelCopyToWMask | |||
| Integer32 as pktSwchChannelCopyMask | |||
| PktSwchChannelAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchChannelIfIndexA | |||
| Integer32 as pktSwchChannelNumberA | |||
| Integer32 as pktSwchChannelProfileA | |||
| Integer32 as pktSwchChannelOutCallProfileA | |||
| Integer32 as pktSwchChannelInCallProfileA | |||
| Integer32 as pktSwchChannelRemoteProfileA | |||
| Integer32 as pktSwchChannelAutocallIdA | |||
| Integer32 as pktSwchChannelAlterAutocallIdA | |||
| Integer32 as pktSwchChannelAutocallRetriesA | |||
| Integer32 as pktSwchChannelAutocallIntervalA | |||
| Integer32 as pktSwchChannelCallAliasA | |||
| Integer32 as pktSwchChannelSubAddress1A | |||
| Integer32 as pktSwchChannelSubAddress2A | |||
| Integer32 as pktSwchChannelNUIAEntry | |||
| Integer32 as pktSwchChannelClearTimerA | |||
| Integer32 as pktSwchChannelOptionsA | |||
| PktSwchCallIdSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchCallIdNumberS | |||
| DisplayString as pktSwchCallIdMnemonicS | |||
| DisplayString as pktSwchCallIdAddressS | |||
| INTEGER as pktSwchCallIdStatusS | |||
| PktSwchCallIdAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchCallIdNumberA | |||
| DisplayString as pktSwchCallIdMnemonicA | |||
| DisplayString as pktSwchCallIdAddressA | |||
| PktSwchAliasSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchAliasNumberS | |||
| DisplayString as pktSwchAliasValueS | |||
| INTEGER as pktSwchAliasStatusS | |||
| PktSwchAliasAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchAliasNumberA | |||
| DisplayString as pktSwchAliasValueA | |||
| PktSwchAsyncStatEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchAsyncIfIndex | |||
| Integer32 as pktSwchAsyncChannelNumber | |||
| INTEGER as pktSwchAsyncConnectionStatus | |||
| Integer32 as pktSwchAsyncNumLogChannels | |||
| Integer32 as pktSwchAsyncNumActSessions | |||
| Integer32 as pktSwchAsyncAutocallId | |||
| INTEGER as pktSwchAsyncRTSStatus | |||
| Integer32 as pktSwchAsyncBuffToNet | |||
| Integer32 as pktSwchAsyncBuffToUser | |||
| INTEGER as pktSwchAsyncTxXoff | |||
| INTEGER as pktSwchAsyncRxXoff | |||
| Integer32 as pktSwchAsyncBuffOutstand | |||
| INTEGER as pktSwchAsyncChannelMode | |||
| PktSwchAsyncRunProEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchAsyncRunProIfIndex | |||
| Integer32 as pktSwchAsyncRunProChannelNumber | |||
| Integer32 as pktSwchAsyncRunProRecallChar | |||
| INTEGER as pktSwchAsyncRunProEcho | |||
| Integer32 as pktSwchAsyncRunProDataForwChar | |||
| Integer32 as pktSwchAsyncRunProIdleTimer | |||
| INTEGER as pktSwchAsyncRunProDevFlowCont | |||
| INTEGER as pktSwchAsyncRunProServSig | |||
| Integer32 as pktSwchAsyncRunProBreak | |||
| INTEGER as pktSwchAsyncRunProDiscOut | |||
| Integer32 as pktSwchAsyncRunProCRPPadding | |||
| Integer32 as pktSwchAsyncRunProLineFold | |||
| INTEGER as pktSwchAsyncRunProSpeed | |||
| INTEGER as pktSwchAsyncRunProPadFlowCont | |||
| INTEGER as pktSwchAsyncRunProLineFeedInsert | |||
| Integer32 as pktSwchAsyncRunProLineFeedPad | |||
| INTEGER as pktSwchAsyncRunProEditing | |||
| Integer32 as pktSwchAsyncRunProCharDel | |||
| Integer32 as pktSwchAsyncRunProLineDel | |||
| Integer32 as pktSwchAsyncRunProLineDisp | |||
| Integer32 as pktSwchAsyncRunProEditServSig | |||
| Integer32 as pktSwchAsyncRunProEchomask | |||
| INTEGER as pktSwchAsyncRunProParTreat | |||
| Integer32 as pktSwchAsyncRunProPageWait | |||
| PktSwchPhyInterfaceEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPhyInterfaceIfIndex | |||
| INTEGER as pktSwchPhyInterfaceProtocolS | |||
| INTEGER as pktSwchPhyInterfaceProtocolA | |||
| Integer32 as pktSwchPhyInterfaceCopyTo | |||
| INTEGER as pktSwchPhyInterfaceChanged | |||
| Integer32 as pktSwchPhyInterfaceRxBuffInPool | |||
| INTEGER as pktSwchPhyInterfaceConnector | |||
| IpAddress as pktSwchPhyInterfaceNeighborIp | |||
| INTEGER as pktSwchPhyInterfaceProtocolStatus | |||
| INTEGER as pktSwchPhyInterfaceTestCmd | |||
| Counter32 as pktSwchPhyInterfaceTestTransmittedFrames | |||
| Counter32 as pktSwchPhyInterfaceTestReceivedFrames | |||
| Integer32 as pktSwchPhyInterfaceTestLostFrames | |||
| PktSwchLapbSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchLapbLinkNumberS | |||
| INTEGER as pktSwchLapbInternalClockS | |||
| Integer32 as pktSwchLapbLineOptionS | |||
| Integer32 as pktSwchLapbSegmentSizeS | |||
| Integer32 as pktSwchLapbXIDS | |||
| Integer32 as pktSwchLapbAckCounterS | |||
| Integer32 as pktSwchLapbAckTimerS | |||
| PktSwchLapbAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchLapbLinkNumberA | |||
| INTEGER as pktSwchLapbInternalClockA | |||
| Integer32 as pktSwchLapbLineOptionA | |||
| Integer32 as pktSwchLapbSegmentSizeA | |||
| INTEGER as pktSwchLapbLineProtocol | |||
| Integer32 as pktSwchLapbLowerId | |||
| Integer32 as pktSwchLapbXIDA | |||
| Counter32 as pktSwchLapbTransmittedIFrames | |||
| Counter32 as pktSwchLapbReceivedIFrames | |||
| Counter32 as pktSwchLapbNSError | |||
| Counter32 as pktSwchLapbTransmittedRRFrames | |||
| Counter32 as pktSwchLapbReceivedRRFrames | |||
| Counter32 as pktSwchLapbTransmittedRNRFrames | |||
| Counter32 as pktSwchLapbReceivedRNRFrames | |||
| Counter32 as pktSwchLapbTransmittedFRMRFrames | |||
| Counter32 as pktSwchLapbReceivedFRMRFrames | |||
| Integer32 as pktSwchLapbAckCounterA | |||
| Integer32 as pktSwchLapbAckTimerA | |||
| PktSwchPlpSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPlpLinkNumberS | |||
| Integer32 as pktSwchPlpInCallOptionS | |||
| Integer32 as pktSwchPlpOutCallOptionS | |||
| INTEGER as pktSwchPlpCugSubscriptionS | |||
| Integer32 as pktSwchPlpNUIS | |||
| Integer32 as pktSwchPlpCpyPktSize | |||
| Integer32 as pktSwchPlpCpyWinSize | |||
| PktSwchPlpAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPlpLinkNumberA | |||
| Integer32 as pktSwchPlpInCallOptionA | |||
| Integer32 as pktSwchPlpOutCallOptionA | |||
| INTEGER as pktSwchPlpCugSubscriptionA | |||
| Integer32 as pktSwchPlpNUIA | |||
| Counter32 as pktSwchStatOutRestarts | |||
| PktSwchCugSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchCugLinkNumberS | |||
| Integer32 as pktSwchCugIndexS | |||
| Integer32 as pktSwchCugNumberS | |||
| INTEGER as pktSwchCugStatus | |||
| PktSwchCugAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchCugLinkNumberA | |||
| Integer32 as pktSwchCugIndexA | |||
| Integer32 as pktSwchCugNumberA | |||
| PktSwchLogChAssEntry | |||
| SEQUENCE | |||
| IfIndexType as pktSwchLogChAssIndex | |||
| Integer32 as pktSwchLogChAssLIC | |||
| Integer32 as pktSwchLogChAssHIC | |||
| Integer32 as pktSwchLogChAssLTC | |||
| Integer32 as pktSwchLogChAssHTC | |||
| Integer32 as pktSwchLogChAssLOC | |||
| Integer32 as pktSwchLogChAssHOC | |||
| PktSwchLogChPartnerEntry | |||
| SEQUENCE | |||
| IfIndexType as pktSwchLogChPartnerIfIndex | |||
| Integer32 as pktSwchLogChPartnerLcIndex | |||
| INTEGER as pktSwchLogChPartnerProtocol | |||
| IfIndexType as pktSwchLogChPartnerOpIfIndex | |||
| Integer32 as pktSwchLogChPartnerOpLcIndex | |||
| PktSwchHdlcSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchHdlcLinkNumberS | |||
| DisplayString as pktSwchHdlcDestAddrS | |||
| Integer32 as pktSwchHdlcDestSubAddrS | |||
| Integer32 as pktSwchHdlcRedialTimeoutS | |||
| Integer32 as pktSwchHdlcRedialRetriesS | |||
| Integer32 as pktSwchHdlcInactivityS | |||
| Integer32 as pktSwchHdlcX25FacilitiesS | |||
| Integer32 as pktSwchHdlcLocalSubaddr1S | |||
| Integer32 as pktSwchHdlcLocalSubaddr2S | |||
| Integer32 as pktSwchHdlcDestDlciS | |||
| Integer32 as pktSwchHdlcDestPortS | |||
| INTEGER as pktSwchHdlcProtocolS | |||
| Integer32 as pktSwchHdlcFlowContOptionsS | |||
| Integer32 as pktSwchHdlcBufferFlowControlS | |||
| INTEGER as pktSwchHdlcInternalClockS | |||
| Integer32 as pktSwchHdlcNrzModeS | |||
| PktSwchHdlcAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchHdlcLinkNumberA | |||
| DisplayString as pktSwchHdlcDestAddrA | |||
| Integer32 as pktSwchHdlcDestSubAddrA | |||
| Integer32 as pktSwchHdlcRedialTimeoutA | |||
| Integer32 as pktSwchHdlcRedialRetriesA | |||
| Integer32 as pktSwchHdlcInactivityA | |||
| Integer32 as pktSwchHdlcX25FacilitiesA | |||
| Integer32 as pktSwchHdlcLocalSubaddr1A | |||
| Integer32 as pktSwchHdlcLocalSubaddr2A | |||
| Integer32 as pktSwchHdlcDestDlciA | |||
| Integer32 as pktSwchHdlcDestPortA | |||
| INTEGER as pktSwchHdlcProtocolA | |||
| Integer32 as pktSwchHdlcFlowContOptionsA | |||
| Integer32 as pktSwchHdlcBufferFlowControlA | |||
| INTEGER as pktSwchHdlcInternalClockA | |||
| Integer32 as pktSwchHdlcNrzModeA | |||
| INTEGER as pktSwchHdlcConnStatus | |||
| INTEGER as pktSwchHdlcSpecialStatus | |||
| INTEGER as pktSwchHdlcCtsStatus | |||
| DisplayString as pktSwchHdlcRunningX25Lcn | |||
| DisplayString as pktSwchHdlcRunningDlci | |||
| Integer32 as pktSwchHdlcMaxBuffToNet | |||
| Integer32 as pktSwchHdlcBuffToNet | |||
| PktSwchStmEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchStmLinkNumber | |||
| INTEGER as pktSwchStmInternalClockS | |||
| INTEGER as pktSwchStmInternalClockA | |||
| INTEGER as pktSwchStmConn | |||
| Counter32 as pktSwchStmSyncLoss | |||
| PktSwchFrSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrIfIndexS | |||
| Integer32 as pktSwchFrMaintProtS | |||
| INTEGER as pktSwchFrMaintModeS | |||
| Integer32 as pktSwchFrRxPoolRedLineS | |||
| Integer32 as pktSwchFrRxPoolOkS | |||
| Integer32 as pktSwchFrTxPoolRedLineS | |||
| Integer32 as pktSwchFrTxPoolOkS | |||
| Integer32 as pktSwchFrTxCeilingS | |||
| INTEGER as pktSwchFrInternalClockS | |||
| INTEGER as pktSwchFrNrzModeS | |||
| INTEGER as pktSwchFrDlciHeaderModeS | |||
| INTEGER as pktSwchFrDcdLinkFailureS | |||
| INTEGER as pktSwchFrTxIdlesS | |||
| INTEGER as pktSwchFrOperationModeS | |||
| INTEGER as pktSwchFrPhysInterfOptionsS | |||
| PktSwchFrAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrIfIndexA | |||
| Integer32 as pktSwchFrMaintProtA | |||
| INTEGER as pktSwchFrMaintModeA | |||
| Integer32 as pktSwchFrRxPoolRedLineA | |||
| Integer32 as pktSwchFrRxPoolOkA | |||
| Integer32 as pktSwchFrTxPoolRedLineA | |||
| Integer32 as pktSwchFrTxPoolOkA | |||
| Integer32 as pktSwchFrTxCeilingA | |||
| INTEGER as pktSwchFrInternalClockA | |||
| INTEGER as pktSwchFrNrzModeA | |||
| Integer32 as pktSwchFrDlcmiPollingInterval | |||
| Integer32 as pktSwchFrDlcmiFullEnquiryInterval | |||
| Integer32 as pktSwchFrDlcmiErrorThreshold | |||
| Integer32 as pktSwchFrDlcmiMonitoredEvents | |||
| INTEGER as pktSwchFrDlciHeaderModeA | |||
| INTEGER as pktSwchFrDcdLinkFailureA | |||
| INTEGER as pktSwchFrTxIdlesA | |||
| INTEGER as pktSwchFrOperationModeA | |||
| INTEGER as pktSwchFrPhysInterfOptionsA | |||
| PktSwchFrIfEntry | |||
| SEQUENCE | |||
| Counter32 as pktSwchFrIfTxBytes | |||
| Counter32 as pktSwchFrIfRxBytes | |||
| Counter32 as pktSwchFrIfTxCongDiscards | |||
| Counter32 as pktSwchFrIfDeTxFrames | |||
| Counter32 as pktSwchFrIfDeRxFrames | |||
| Counter32 as pktSwchFrIfFecnTxFrames | |||
| Counter32 as pktSwchFrIfFecnRxFrames | |||
| Counter32 as pktSwchFrIfBecnTxFrames | |||
| Counter32 as pktSwchFrIfBecnRxFrames | |||
| Counter32 as pktSwchFrIfCommRateViolTxFrames | |||
| Counter32 as pktSwchFrIfCommRateViolRxFrames | |||
| Counter32 as pktSwchFrIfExcessRateViolTxFrames | |||
| Counter32 as pktSwchFrIfExcessRateViolRxFrames | |||
| Integer32 as pktSwchFrIfBuffersInTxPool | |||
| Integer32 as pktSwchFrIfFreeBuffersInRxPool | |||
| Counter32 as pktSwchFrIfLmiTxFrames | |||
| Counter32 as pktSwchFrIfLmiRxFrames | |||
| Counter32 as pktSwchFrIfAnsiTxFrames | |||
| Counter32 as pktSwchFrIfAnsiRxFrames | |||
| Counter32 as pktSwchFrIfCllmTxFrames | |||
| Counter32 as pktSwchFrIfCllmRxFrames | |||
| Counter32 as pktSwchFrIfTxCongestions | |||
| Counter32 as pktSwchFrIfRxCongestions | |||
| Integer32 as pktSwchFrIfTotDlciNumber | |||
| PktSwchFrCircuitSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrCircuitIfIndexS | |||
| Integer32 as pktSwchFrCircuitIndexS | |||
| INTEGER as pktSwchFrCircuitDestProtS | |||
| DisplayString as pktSwchFrCircuitDestIdS | |||
| DisplayString as pktSwchFrCircuitBackIdS | |||
| Integer32 as pktSwchFrCircuitTxCirIntervalS | |||
| Integer32 as pktSwchFrCircuitTxCommittedS | |||
| Integer32 as pktSwchFrCircuitTxExcessS | |||
| Integer32 as pktSwchFrCircuitRxCirIntervalS | |||
| Integer32 as pktSwchFrCircuitRxCommittedS | |||
| Integer32 as pktSwchFrCircuitRxExcessS | |||
| Integer32 as pktSwchFrCircuitFunnelIdS | |||
| INTEGER as pktSwchFrCircuitStatusS | |||
| Integer32 as pktSwchFrCircuitExtendedDlciS | |||
| Integer32 as pktSwchFrCircuitTxPriorityS | |||
| Integer32 as pktSwchFrCircuitIsdnRoutIdS | |||
| PktSwchFrCircuitAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrCircuitIfIndexA | |||
| Integer32 as pktSwchFrCircuitIndexA | |||
| INTEGER as pktSwchFrCircuitDestProtA | |||
| DisplayString as pktSwchFrCircuitDestIdA | |||
| DisplayString as pktSwchFrCircuitBackIdA | |||
| Integer32 as pktSwchFrCircuitTxCirIntervalA | |||
| Integer32 as pktSwchFrCircuitTxCommittedA | |||
| Integer32 as pktSwchFrCircuitTxExcessA | |||
| Integer32 as pktSwchFrCircuitRxCirIntervalA | |||
| Integer32 as pktSwchFrCircuitRxCommittedA | |||
| Integer32 as pktSwchFrCircuitRxExcessA | |||
| Integer32 as pktSwchFrCircuitFunnelIdA | |||
| DisplayString as pktSwchFrCircuitFunnelStat | |||
| Counter32 as pktSwchFrCircuitTxCongDiscards | |||
| Counter32 as pktSwchFrCircuitDeTxFrames | |||
| Counter32 as pktSwchFrCircuitDeRxFrames | |||
| Counter32 as pktSwchFrCircuitFecnTxFrames | |||
| Counter32 as pktSwchFrCircuitBecnTxFrames | |||
| Counter32 as pktSwchFrCircuitCommRateViolTxFrames | |||
| Counter32 as pktSwchFrCircuitCommRateViolRxFrames | |||
| Counter32 as pktSwchFrCircuitExcessRateViolTxFrames | |||
| Counter32 as pktSwchFrCircuitExcessRateViolRxFrames | |||
| INTEGER as pktSwchFrCircuitState | |||
| Integer32 as pktSwchFrCircuitExtendedDlciA | |||
| Integer32 as pktSwchFrCircuitTxPriorityA | |||
| Integer32 as pktSwchFrCircuitIsdnRoutIdA | |||
| PktSwchFrFunnelSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrFunnelIndexS | |||
| Integer32 as pktSwchFrFunnelSizeS | |||
| Integer32 as pktSwchFrFunnelHighWaterFramesS | |||
| Integer32 as pktSwchFrFunnelHighWaterBytesS | |||
| Integer32 as pktSwchFrFunnelGaugeTxRateS | |||
| Integer32 as pktSwchFrFunnelTransWindowS | |||
| INTEGER as pktSwchFrFunnelStatusS | |||
| PktSwchFrFunnelAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrFunnelIndexA | |||
| Integer32 as pktSwchFrFunnelSizeA | |||
| Integer32 as pktSwchFrFunnelHighWaterFramesA | |||
| Integer32 as pktSwchFrFunnelHighWaterBytesA | |||
| Integer32 as pktSwchFrFunnelGaugeTxRateA | |||
| Integer32 as pktSwchFrFunnelTransWindowA | |||
| PktSwchFrDlciMapEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchFrDlciMapPort | |||
| Integer32 as pktSwchFrDlciMapLongDlci | |||
| Integer32 as pktSwchFrDlciMapShortDlci | |||
| INTEGER as pktSwchFrDlciMapStatus | |||
| PktSwchMpeSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchMpeLinkNumberS | |||
| Integer32 as pktSwchMpeInactivityS | |||
| Integer32 as pktSwchMpeX25FacilitiesS | |||
| Integer32 as pktSwchMpeLocSubAddr1S | |||
| Integer32 as pktSwchMpeLocSubAddr2S | |||
| Integer32 as pktSwchMpeFlwCtrlDurS | |||
| Integer32 as pktSwchMpeFlwCtrlOptS | |||
| Integer32 as pktSwchMpeFlwCtrlBufS | |||
| INTEGER as pktSwchMpeInternalClkS | |||
| PktSwchMpeAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchMpeLinkNumberA | |||
| Integer32 as pktSwchMpeInactivityA | |||
| Integer32 as pktSwchMpeX25FacilitiesA | |||
| Integer32 as pktSwchMpeLocSubAddr1A | |||
| Integer32 as pktSwchMpeLocSubAddr2A | |||
| Integer32 as pktSwchMpeFlwCtrlDurA | |||
| Integer32 as pktSwchMpeFlwCtrlOptA | |||
| Integer32 as pktSwchMpeFlwCtrlBufA | |||
| INTEGER as pktSwchMpeInternalClkA | |||
| INTEGER as pktSwchMpeCtsStatus | |||
| PktSwchMpeAidSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchMpeAddressIdS | |||
| INTEGER as pktSwchMpeAidMainTypeS | |||
| Integer32 as pktSwchMpeAidMainIdS | |||
| Integer32 as pktSwchMpeAidMainSubIdS | |||
| INTEGER as pktSwchMpeAidBackupTypeS | |||
| Integer32 as pktSwchMpeAidBackupIdS | |||
| Integer32 as pktSwchMpeAidBackupSubIdS | |||
| INTEGER as pktSwchMpeAidStatusS | |||
| PktSwchMpeAidAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchMpeAddressIdA | |||
| INTEGER as pktSwchMpeAidMainTypeA | |||
| Integer32 as pktSwchMpeAidMainIdA | |||
| Integer32 as pktSwchMpeAidMainSubIdA | |||
| INTEGER as pktSwchMpeAidBackupTypeA | |||
| Integer32 as pktSwchMpeAidBackupIdA | |||
| Integer32 as pktSwchMpeAidBackupSubIdA | |||
| INTEGER as pktSwchMpeAidConn | |||
| INTEGER as pktSwchMpeAidFlwCtrl | |||
| PktSwchSlipSEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchSlipLinkNumberS | |||
| INTEGER as pktSwchSlipSpeedS | |||
| Integer32 as pktSwchSlipFCOptionS | |||
| INTEGER as pktSwchSlipStopBitsS | |||
| Integer32 as pktSwchSlipBitPerCharS | |||
| INTEGER as pktSwchSlipParityS | |||
| IpAddress as pktSwchSlipIpAddressS | |||
| IpAddress as pktSwchSlipIpMaskS | |||
| INTEGER as pktSwchSlipDefEncapsTypeS | |||
| DisplayString as pktSwchSlipDefDestinationS | |||
| PktSwchSlipAEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchSlipLinkNumberA | |||
| INTEGER as pktSwchSlipSpeedA | |||
| Integer32 as pktSwchSlipFCOptionA | |||
| INTEGER as pktSwchSlipStopBitsA | |||
| Integer32 as pktSwchSlipBitPerCharA | |||
| INTEGER as pktSwchSlipParityA | |||
| IpAddress as pktSwchSlipIpAddressA | |||
| IpAddress as pktSwchSlipIpMaskA | |||
| INTEGER as pktSwchSlipDefEncapsTypeA | |||
| DisplayString as pktSwchSlipDefDestinationA | |||
| PktSwchSnaSDLCLinkEntryS | |||
| SEQUENCE | |||
| INTEGER as pktSwchSnaSDLCLinkTypeS | |||
| INTEGER as pktSwchSnaSDLCLinkPUSharedS | |||
| INTEGER as pktSwchSnaSDLCLinkDuplexPhyS | |||
| Integer32 as pktSwchSnaSDLCLinkflagsS | |||
| INTEGER as pktSwchSnaSDLCLinkDuplexS | |||
| INTEGER as pktSwchSnaSDLCLinkClockS | |||
| INTEGER as pktSwchSnaSDLCLinkNRZS | |||
| PktSwchSnaSDLCLinkEntryA | |||
| SEQUENCE | |||
| INTEGER as pktSwchSnaSDLCLinkTypeA | |||
| INTEGER as pktSwchSnaSDLCLinkPUSharedA | |||
| INTEGER as pktSwchSnaSDLCLinkDuplexPhyA | |||
| Integer32 as pktSwchSnaSDLCLinkflagsA | |||
| INTEGER as pktSwchSnaSDLCLinkDuplexA | |||
| INTEGER as pktSwchSnaSDLCLinkClockA | |||
| INTEGER as pktSwchSnaSDLCLinkNRZA | |||
| Counter32 as pktSwchSnaSDLCLinkStatFrames | |||
| Counter32 as pktSwchSnaSDLCLinkStatErrors | |||
| Counter32 as pktSwchSnaSDLCLinkStatInvalidAddresses | |||
| Counter32 as pktSwchSnaSDLCLinkStatShortFrames | |||
| PktSwchSnaPUEntryS | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUNumberS | |||
| INTEGER as pktSwchSnaPUXIDProcessingS | |||
| INTEGER as pktSwchSnaPUEnableS | |||
| INTEGER as pktSwchSnaPULinkATypeS | |||
| INTEGER as pktSwchSnaPULinkARoleS | |||
| INTEGER as pktSwchSnaPULinkBTypeS | |||
| INTEGER as pktSwchSnaPULinkBRoleS | |||
| INTEGER as pktSwchSnaPUEntryStatusS | |||
| PktSwchSnaPUEntryA | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUNumberA | |||
| INTEGER as pktSwchSnaPUXIDProcessingA | |||
| INTEGER as pktSwchSnaPUEnableA | |||
| INTEGER as pktSwchSnaPULinkATypeA | |||
| INTEGER as pktSwchSnaPULinkARoleA | |||
| INTEGER as pktSwchSnaPULinkBTypeA | |||
| INTEGER as pktSwchSnaPULinkBRoleA | |||
| PktSwchSnaPUSdlcEntryS | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUSdlcNumberS | |||
| INTEGER as pktSwchSnaPUSdlcSideS | |||
| OCTET STRING as pktSwchSnaPUSdlcAddressS | |||
| Integer32 as pktSwchSnaPUSdlcIfIndexS | |||
| OCTET STRING as pktSwchSnaPUSdlcIdBlkS | |||
| OCTET STRING as pktSwchSnaPUSdlcIdNumS | |||
| Integer32 as pktSwchSnaPUSdlcMaxPiuSizeS | |||
| Integer32 as pktSwchSnaPUSdlcTxWindowS | |||
| OCTET STRING as pktSwchSnaPUSdlcGrpAddressS | |||
| Integer32 as pktSwchSnaPUSdlcPollTimerS | |||
| INTEGER as pktSwchSnaPUSdlcXIDInitiationS | |||
| INTEGER as pktSwchSnaPUSdlcEntryStatusS | |||
| PktSwchSnaPUSdlcEntryA | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUSdlcNumberA | |||
| INTEGER as pktSwchSnaPUSdlcSideA | |||
| OCTET STRING as pktSwchSnaPUSdlcAddressA | |||
| Integer32 as pktSwchSnaPUSdlcIfIndexA | |||
| OCTET STRING as pktSwchSnaPUSdlcIdBlkA | |||
| OCTET STRING as pktSwchSnaPUSdlcIdNumA | |||
| Integer32 as pktSwchSnaPUSdlcMaxPiuSizeA | |||
| Integer32 as pktSwchSnaPUSdlcTxWindowA | |||
| OCTET STRING as pktSwchSnaPUSdlcGrpAddressA | |||
| Integer32 as pktSwchSnaPUSdlcPollTimerA | |||
| INTEGER as pktSwchSnaPUSdlcXIDInitiationA | |||
| PktSwchSnaPUSdlcStatEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUSdlcStatNumber | |||
| INTEGER as pktSwchSnaPUSdlcStatSide | |||
| Counter32 as pktSwchSnaPUSdlcStatOctetsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatOctetsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatIFramesIn | |||
| Counter32 as pktSwchSnaPUSdlcStatIFramesOut | |||
| Counter32 as pktSwchSnaPUSdlcStatRRFramesIn | |||
| Counter32 as pktSwchSnaPUSdlcStatRRFramesOut | |||
| Counter32 as pktSwchSnaPUSdlcStatRNRFramesIn | |||
| Counter32 as pktSwchSnaPUSdlcStatRNRFramesOut | |||
| Counter32 as pktSwchSnaPUSdlcStatXIDsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatXIDsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatTESTsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatTESTsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatREJsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatREJsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatFRMRsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatFRMRsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatDISCsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatDISCsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatUAsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatUAsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatDMsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatDMsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatSNRMsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatSNRMsOut | |||
| Counter32 as pktSwchSnaPUSdlcStatRetransmitsIn | |||
| Counter32 as pktSwchSnaPUSdlcStatRetransmitsOut | |||
| INTEGER as pktSwchSnaPUSdlcUpperState | |||
| INTEGER as pktSwchSnaPUSdlcLowerState | |||
| INTEGER as pktSwchSnaPUSdlcStatNRMStatus | |||
| INTEGER as pktSwchSnaPUSdlcStatFlowCtlStatus | |||
| PktSwchSnaPUX25QllcEntryS | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUX25QllcNumberS | |||
| INTEGER as pktSwchSnaPUX25QllcSideS | |||
| OCTET STRING as pktSwchSnaPUX25QllcIdBlkS | |||
| OCTET STRING as pktSwchSnaPUX25QllcIdNumS | |||
| INTEGER as pktSwchSnaPUX25QllcXIDInitS | |||
| Integer32 as pktSwchSnaPUX25QllcMaxPiuSizeS | |||
| OCTET STRING as pktSwchSnaPUX25QllcStationAddressS | |||
| DisplayString as pktSwchSnaPUX25QllcInPasswordS | |||
| Integer32 as pktSwchSnaPUX25QllcSubAddressS | |||
| INTEGER as pktSwchSnaPUX25QllcAutoCallS | |||
| OCTET STRING as pktSwchSnaPUX25QllcCalledAddressS | |||
| DisplayString as pktSwchSnaPUX25QllcCallUserDataFacilitiesS | |||
| INTEGER as pktSwchSnaPUX25QllcEntryStatusS | |||
| PktSwchSnaPUX25QllcEntryA | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUX25QllcNumberA | |||
| INTEGER as pktSwchSnaPUX25QllcSideA | |||
| OCTET STRING as pktSwchSnaPUX25QllcIdBlkA | |||
| OCTET STRING as pktSwchSnaPUX25QllcIdNumA | |||
| INTEGER as pktSwchSnaPUX25QllcXIDInitA | |||
| Integer32 as pktSwchSnaPUX25QllcMaxPiuSizeA | |||
| OCTET STRING as pktSwchSnaPUX25QllcStationAddressA | |||
| DisplayString as pktSwchSnaPUX25QllcInPasswordA | |||
| Integer32 as pktSwchSnaPUX25QllcSubAddressA | |||
| INTEGER as pktSwchSnaPUX25QllcAutoCallA | |||
| OCTET STRING as pktSwchSnaPUX25QllcCalledAddressA | |||
| DisplayString as pktSwchSnaPUX25QllcCallUserDataFacilitiesA | |||
| PktSwchSnaPUX25QllcStatEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPUX25QllcStatNumber | |||
| INTEGER as pktSwchSnaPUX25QllcStatSide | |||
| Integer32 as pktSwchSnaPUX25QllcStatlink | |||
| Counter32 as pktSwchSnaPUX25QllcStatDataPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatDataPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatQSMPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatQSMPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatQDMPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatQDMPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatXIDPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatXIDPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatQDISCPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatQDISCPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatCallPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatCallPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatClearPacketsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatClearPacketsOut | |||
| Counter32 as pktSwchSnaPUX25QllcStatCallAcceptsIn | |||
| Counter32 as pktSwchSnaPUX25QllcStatCallAcceptsOut | |||
| INTEGER as pktSwchSnaPUX25QllcStatUpperState | |||
| INTEGER as pktSwchSnaPUX25QllcStatLowerState | |||
| INTEGER as pktSwchSnaPUX25QllcStatNRMStatus | |||
| INTEGER as pktSwchSnaPUX25QllcStatFlowCtlStatus | |||
| PktSwchSnaPULlc2FrEntryS | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPULlc2FrNumberS | |||
| INTEGER as pktSwchSnaPULlc2FrSideS | |||
| INTEGER as pktSwchSnaPULlc2FrEncapsTypeS | |||
| OCTET STRING as pktSwchSnaPULlc2FrDestMACS | |||
| OCTET STRING as pktSwchSnaPULlc2FrSrcSAPS | |||
| OCTET STRING as pktSwchSnaPULlc2FrDestSAPS | |||
| OCTET STRING as pktSwchSnaPULlc2FrXIDIdBlkS | |||
| OCTET STRING as pktSwchSnaPULlc2FrXIDIdNumS | |||
| Integer32 as pktSwchSnaPULlc2FrMaxPiuSizeS | |||
| Integer32 as pktSwchSnaPULlc2FrTxWindowS | |||
| Integer32 as pktSwchSnaPULlc2FrLinkS | |||
| Integer32 as pktSwchSnaPULlc2FrDLCIS | |||
| INTEGER as pktSwchSnaPULlc2FrXIDInitiationS | |||
| Integer32 as pktSwchSnaPULlc2FrN2CountS | |||
| Integer32 as pktSwchSnaPULlc2FrT1TimerS | |||
| Integer32 as pktSwchSnaPULlc2FrTiTimerS | |||
| INTEGER as pktSwchSnaPULlc2FrEntryStatusS | |||
| PktSwchSnaPULlc2FrEntryA | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPULlc2FrNumberA | |||
| INTEGER as pktSwchSnaPULlc2FrSideA | |||
| INTEGER as pktSwchSnaPULlc2FrEncapsTypeA | |||
| OCTET STRING as pktSwchSnaPULlc2FrDestMACA | |||
| OCTET STRING as pktSwchSnaPULlc2FrSrcSAPA | |||
| OCTET STRING as pktSwchSnaPULlc2FrDestSAPA | |||
| OCTET STRING as pktSwchSnaPULlc2FrXIDIdBlkA | |||
| OCTET STRING as pktSwchSnaPULlc2FrXIDIdNumA | |||
| Integer32 as pktSwchSnaPULlc2FrMaxPiuSizeA | |||
| Integer32 as pktSwchSnaPULlc2FrTxWindowA | |||
| Integer32 as pktSwchSnaPULlc2FrLinkA | |||
| Integer32 as pktSwchSnaPULlc2FrDLCIA | |||
| INTEGER as pktSwchSnaPULlc2FrXIDInitiationA | |||
| Integer32 as pktSwchSnaPULlc2FrN2CountA | |||
| Integer32 as pktSwchSnaPULlc2FrT1TimerA | |||
| Integer32 as pktSwchSnaPULlc2FrTiTimerA | |||
| PktSwchSnaPULlc2FrStatEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchSnaPULlc2FrStatNumber | |||
| INTEGER as pktSwchSnaPULlc2FrStatSide | |||
| Counter32 as pktSwchSnaPULlc2FrStatOctetsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatOctetsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatIFramesIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatIFramesOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatRRFramesIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatRRFramesOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatRNRFramesIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatRNRFramesOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatXIDsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatXIDsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatTESTsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatTESTsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatREJsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatREJsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatFRMRsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatFRMRsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatDISCsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatDISCsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatUAsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatUAsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatDMsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatDMsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatSABMEsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatSABMEsOut | |||
| Counter32 as pktSwchSnaPULlc2FrStatRetransmitsIn | |||
| Counter32 as pktSwchSnaPULlc2FrStatRetransmitsOut | |||
| INTEGER as pktSwchSnaPULlc2FrStatUpperState | |||
| INTEGER as pktSwchSnaPULlc2FrStatLowerState | |||
| INTEGER as pktSwchSnaPULlc2FrStatNRMStatus | |||
| INTEGER as pktSwchSnaPULlc2FrStatFlowCtlStatus | |||
| PktSwchEthernetLinkEntry | |||
| SEQUENCE | |||
| INTEGER as pktSwchEthernetLinkOperationMode | |||
| OCTET STRING as pktSwchEthernetLinkUserDefMacAddr | |||
| DisplayString as pktSwchEthernetLinkPointToPointDest | |||
| Counter32 as pktSwchEthernetLinkTotalFramesIn | |||
| Counter32 as pktSwchEthernetLinkTotalFramesOut | |||
| Counter32 as pktSwchEthernetLinkIpFramesIn | |||
| Counter32 as pktSwchEthernetLinkIpFramesOut | |||
| Counter32 as pktSwchEthernetLinkLlc2FramesIn | |||
| Counter32 as pktSwchEthernetLinkLlc2FramesOut | |||
| Counter32 as pktSwchEthernetLinkBridgFramesIn | |||
| Counter32 as pktSwchEthernetLinkBridgFramesOut | |||
| Counter32 as pktSwchEthernetLinkDiscardedByFilter | |||
| PktSwchEthernetFilterEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchEthernetFilterId | |||
| OCTET STRING as pktSwchEthernetFilterMacAddr | |||
| INTEGER as pktSwchEthernetFilterProtType | |||
| DisplayString as pktSwchEthernetFilterDest | |||
| INTEGER as pktSwchEthernetFilterStatus | |||
| PktSwchEthernetBroadcastDestEntry | |||
| SEQUENCE | |||
| INTEGER as pktSwchEthernetBroadcastDestProtocol | |||
| Integer32 as pktSwchEthernetBroadcastDestId | |||
| DisplayString as pktSwchEthernetBroadcastDestDestination | |||
| INTEGER as pktSwchEthernetBroadcastDestStatus | |||
| PktSwchIpInterfaceEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIpInterfaceId | |||
| IpAddress as pktSwchIpInterfaceAddress | |||
| IpAddress as pktSwchIpInterfaceAddressMask | |||
| INTEGER as pktSwchIpInterfaceSendDefRoutMsgOnly | |||
| DisplayString as pktSwchIpInterfaceDest | |||
| Integer32 as pktSwchIpInterfaceInactivity | |||
| Integer32 as pktSwchIpInterfaceLinkCost | |||
| INTEGER as pktSwchIpInterfaceOptions | |||
| INTEGER as pktSwchIpInterfaceStatus | |||
| Counter32 as pktSwchIpInterfaceRxFrames | |||
| Counter32 as pktSwchIpInterfaceRxExpiredTtl | |||
| Counter32 as pktSwchIpInterfaceRxUnknownDest | |||
| Counter32 as pktSwchIpInterfaceTxFrames | |||
| Counter32 as pktSwchIpInterfaceTxQueueBufs | |||
| Counter32 as pktSwchIpInterfaceTxDiscarded | |||
| Counter32 as pktSwchIpInterfaceRipRxFrames | |||
| Counter32 as pktSwchIpInterfaceRipTxFrames | |||
| Counter32 as pktSwchIpInterfaceRipWaitingMsgs | |||
| PktSwchIsdnRoutEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIsdnRoutId | |||
| INTEGER as pktSwchIsdnRoutDataBandWidth | |||
| INTEGER as pktSwchIsdnRoutOptions | |||
| INTEGER as pktSwchIsdnRoutStatus | |||
| PktSwchIsdnOutAddrEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIsdnOutAddrRoutId | |||
| Integer32 as pktSwchIsdnOutAddrId | |||
| DisplayString as pktSwchIsdnOutAddr | |||
| DisplayString as pktSwchIsdnOutSubAddr | |||
| PktSwchIsdnAcceptEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchIsdnAcceptId | |||
| Integer32 as pktSwchIsdnAcceptSecondaryLink | |||
| DisplayString as pktSwchIsdnAcceptDialbkSubAddress | |||
| INTEGER as pktSwchIsdnAcceptStatus | |||
| PktSwchIsdnLinkEntry | |||
| SEQUENCE | |||
| INTEGER as pktSwchIsdnLinkBchannel | |||
| Counter32 as pktSwchIsdnCallsClrs | |||
| INTEGER as pktSwchIsdnTestCmd | |||
| DisplayString as pktSwchIsdnTestAddr | |||
| DisplayString as pktSwchIsdnTestSubAddr | |||
| PktSwchPppSecretsEntry | |||
| SEQUENCE | |||
| Integer32 as pktSwchPppSecretsPairId | |||
| INTEGER as pktSwchPppSecretsStatus | |||
| PktSwchPppChanEntry | |||
| SEQUENCE | |||
| INTEGER as pktSwchPppChanSpeed | |||
| Integer32 as pktSwchPppChanFlowCtlDuration | |||
| INTEGER as pktSwchPppChanStopBits | |||
| Integer32 as pktSwchPppChanBitPerChar | |||
| INTEGER as pktSwchPppChanParity | |||
| INTEGER as pktSwchPppChanNegotiationTrigger | |||
| Integer32 as pktSwchPppChanMRU | |||
| OCTET STRING as pktSwchPppChanACCM | |||
| INTEGER as pktSwchPppChanAuthentication | |||
| INTEGER as pktSwchPppChanInternalClock | |||
| Integer32 as pktSwchPppChanBundle | |||
| Integer32 as pktSwchpPppChanIsdnRoutId | |||
| DisplayString as pktSwchpPppChanLastEvent | |||
| ModmSaConfigEntry | |||
| SEQUENCE | |||
| INTEGER as modmSaConfigMode | |||
| INTEGER as modmSaConfigLoopback | |||
| INTEGER as modmSaConfigAlrClearOnCmd | |||
| INTEGER as modmSaConfigAlrClearAllCmd | |||
| INTEGER as modmSaConfigTestClearCmd | |||
| INTEGER as modmSaConfigClkMaster | |||
| INTEGER as modmSaConfigResetStatistics | |||
| Integer32 as modmSaConfigActiveTs | |||
| INTEGER as modmSaConfigReset | |||
| INTEGER as modmSaConfigRemote | |||
| INTEGER as modmSaConfigPsType | |||
| INTEGER as modmSaConfigWorkMode | |||
| ModmSaStatEntry | |||
| SEQUENCE | |||
| Integer32 as modmSaStatHwTest | |||
| OCTET STRING as modmSaStatAlarms | |||
| INTEGER as modmSaStatClkSrc | |||
| OCTET STRING as modmSaStatAlarmsMask | |||
| INTEGER as modmSaStatDeviceType | |||
| DisplayString as modmSaStatSwVersion | |||
| DisplayString as modmSaStatHwVersion | |||
| ModmSaAlarmBuffEntry | |||
| SEQUENCE | |||
| Integer32 as modmSaAlarmBuffIndex | |||
| Integer32 as modmSaAlarmBuffCode | |||
| DisplayString as modmSaAlarmBuffTime | |||
| INTEGER as modmSaAlarmBuffState | |||
| ModmSaRptrEntry | |||
| SEQUENCE | |||
| Integer32 as modmSaIndex | |||
| Integer32 as modmSaRptrIndex | |||
| INTEGER as modmSaRptrTest | |||
| OCTET STRING as modmSaRptrActiveAlarms | |||
| INTEGER as modmSaRptrAlrClear | |||
| DisplayString as modmSaRptrVersion | |||
| MdlParamEntry | |||
| SEQUENCE | |||
| INTEGER as mdlSIdx | |||
| Integer32 as mdlSNoOfModems | |||
| INTEGER as mdlCardType | |||
| INTEGER as mdlSPanelType | |||
| OCTET STRING as mdlSLed | |||
| OCTET STRING as mdlSActiveAlarms | |||
| INTEGER as mdlAlrClear | |||
| INTEGER as mdlSConfigMismatch | |||
| INTEGER as mdlConfigSource | |||
| INTEGER as mdlConfigGround | |||
| ModemParamEntry | |||
| SEQUENCE | |||
| Integer32 as modemIdx | |||
| INTEGER as modemType | |||
| INTEGER as modemConfigMode | |||
| INTEGER as modemModeTemporary | |||
| Integer32 as modemNoOfDte | |||
| INTEGER as modemWire | |||
| INTEGER as modemMngLink | |||
| INTEGER as modemReset | |||
| INTEGER as modemSlot | |||
| OCTET STRING as modemHubId | |||
| IpAddress as modemIpAddress | |||
| INTEGER as modemPsType | |||
| Integer32 as modemMaskTraps | |||
| OCTET STRING as modemActiveAlarms | |||
| INTEGER as modemAlrClear | |||
| INTEGER as modemAlrBufClear | |||
| OCTET STRING as modemMaskSignaling | |||
| INTEGER as modemPanelType | |||
| INTEGER as modemIType | |||
| Integer32 as modemRcvPower | |||
| Integer32 as modemSwVersion | |||
| OCTET STRING as modemLed | |||
| INTEGER as modemRemoteType | |||
| INTEGER as modemConfigPhantom | |||
| INTEGER as modemRemoteTestEnable | |||
| DisplayString as modemSwVerString | |||
| Integer32 as modemRemoteIdx | |||
| DisplayString as modemHwVerString | |||
| INTEGER as modemResetStatistics | |||
| INTEGER as modemMaxRate | |||
| INTEGER as modemBoxMaterial | |||
| ModemAlrBufEntry | |||
| SEQUENCE | |||
| Integer32 as modemAlrBufIdx | |||
| Integer32 as modemAlrBufCode | |||
| INTEGER as modemAlrBufState | |||
| DisplayString as modemAlrBufDate | |||
| DisplayString as modemAlrBufTime | |||
| TimeTicks as modemAlrBufSysUpTime | |||
| ModemGeneralEntry | |||
| SEQUENCE | |||
| Integer32 as modemCurrentElapsedTime | |||
| Integer32 as modemValidIntervals | |||
| ModemIntervalEntry | |||
| SEQUENCE | |||
| Integer32 as modemIntervalNumber | |||
| Integer32 as modemSyncLoss | |||
| INTEGER as modemLineQuality | |||
| Integer32 as modemLineUtility | |||
| Integer32 as modemRTS | |||
| Integer32 as modemCD | |||
| DisplayString as modemBertResult | |||
| OCTET STRING as modemBpvError | |||
| OCTET STRING as modemFoError | |||
| ModmPrtSpEntry | |||
| SEQUENCE | |||
| INTEGER as modmPrtSpUsage | |||
| INTEGER as modmPrtSpRate | |||
| INTEGER as modmPrtSpDataBits | |||
| INTEGER as modmPrtSpParity | |||
| INTEGER as modmPrtSpInterface | |||
| INTEGER as modmPrtSpCTS | |||
| INTEGER as modmPrtSpDcdDelay | |||
| INTEGER as modmPrtSpDsr | |||
| ModmPrtDs1Entry | |||
| SEQUENCE | |||
| OCTET STRING as modmPrtDs1HdslPriorityBumping | |||
| INTEGER as modmPrtDs1Sync | |||
| Gauge32 as modmPrtDs1BpvLastMin | |||
| Gauge32 as modmPrtDs1BpvMax | |||
| INTEGER as modmPrtDs1LineLength | |||
| Gauge32 as modmPrtDs1CRCAvgError | |||
| ModmPrtHdslCurrentEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtHdslCurrentElapsedTime | |||
| Gauge32 as modmPrtHdslCurrentESs | |||
| Gauge32 as modmPrtHdslCurrentSESs | |||
| Gauge32 as modmPrtHdslCurrentBBEs | |||
| Gauge32 as modmPrtHdslCurrentUASs | |||
| Integer32 as modmPrtHdslCurrentNoiseMargin | |||
| Integer32 as modmPrtHdslCurrentAttenuation | |||
| ModmPrtHdslIntervalEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtHdslIntervalNumber | |||
| Gauge32 as modmPrtHdslIntervalESs | |||
| Gauge32 as modmPrtHdslIntervalSESs | |||
| Gauge32 as modmPrtHdslIntervalBBEs | |||
| Gauge32 as modmPrtHdslIntervalUASs | |||
| Integer32 as modmPrtHdslIntervalESR | |||
| Integer32 as modmPrtHdslIntervalSESR | |||
| Integer32 as modmPrtHdslIntervalBBER | |||
| ModmPrtHdslTotalEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtHdslTotalValidIntervals | |||
| Gauge32 as modmPrtHdslTotalESs | |||
| Gauge32 as modmPrtHdslTotalSESs | |||
| Gauge32 as modmPrtHdslTotalBBEs | |||
| Gauge32 as modmPrtHdslTotalUASs | |||
| ModmPrtHdslEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtHdslIndex | |||
| Integer32 as modmPrtHdslDedicatedTs | |||
| OCTET STRING as modmPrtHdslPriorityBumping | |||
| INTEGER as modmPrtHdslMngProtocol | |||
| INTEGER as modmPrtHdslRoutProtocol | |||
| INTEGER as modmPrtHdslInbandMngRate | |||
| ModmPrtDteEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtDteIndex | |||
| INTEGER as modmPrtDteProtocol | |||
| INTEGER as modmPrtDteDataBits | |||
| INTEGER as modmPrtDteStopBits | |||
| INTEGER as modmPrtDteRate | |||
| INTEGER as modmPrtDteCtsDelay | |||
| INTEGER as modmPrtDteParity | |||
| INTEGER as modmPrtDteIfType | |||
| INTEGER as modmPrtDteRlbEnable | |||
| INTEGER as modmPrtDteAlbEnable | |||
| INTEGER as modmPrtDteRtsDcdEnable | |||
| INTEGER as modmPrtDteDsrDtrEnable | |||
| OCTET STRING as modmPrtDteSignaling | |||
| INTEGER as modmPrtDteLoops | |||
| Integer32 as modmPrtDteTests | |||
| INTEGER as modmPrtDteClearAllTests | |||
| DisplayString as modmPrtDteBertResult | |||
| INTEGER as modmPrtDteErrCorrect | |||
| INTEGER as modmPrtDteV54DigitalTest | |||
| INTEGER as modmPrtDteV54DigitalTestStatus | |||
| Integer32 as modmPrtDteTestTimeOut | |||
| ModmPrtLineEntry | |||
| SEQUENCE | |||
| Integer32 as modmPrtLineIndex | |||
| INTEGER as modmPrtLineClkSrc | |||
| INTEGER as modmPrtLineTxLevel | |||
| INTEGER as modmPrtLineRxLevel | |||
| INTEGER as modmPrtLineOutImp | |||
| INTEGER as modmPrtLineInImp | |||
| INTEGER as modmPrtLineCarrCntrl | |||
| INTEGER as modmPrtLineRAP | |||
| INTEGER as modmPrtLineWaveLength | |||
| INTEGER as modmPrtLineCdSense | |||
| INTEGER as modmPrtLineAIS | |||
| INTEGER as modmPrtLineCoding | |||
| INTEGER as modmPrtLineLength | |||
| INTEGER as modmPrtLineClkSrcPort | |||
| INTEGER as modmPrtLineDteClkConfig | |||
| INTEGER as modmPrtLineMaskAlr | |||
| SysDclEntry | |||
| SEQUENCE | |||
| Integer32 as sysDclCnfgIdx | |||
| INTEGER as sysDclRedundancy | |||
| INTEGER as sysDclActiveCl | |||
| INTEGER as sysDclFlipDelay | |||
| INTEGER as sysDclFlipUponStnClk | |||
| SysDclCopyDbEntry | |||
| SEQUENCE | |||
| Integer32 as sysDclCopyDbIdx | |||
| INTEGER as sysDclCopyDbCmd | |||
| SysSErrListEntry | |||
| SEQUENCE | |||
| INTEGER as sysSErrType | |||
| Integer32 as sysSErrIdx | |||
| DisplayString as sysSErrDescription | SIZE(0..255) | ||
| SysSRdnFlipEntry | |||
| SEQUENCE | |||
| Integer32 as sysSRdnFlipIdx | |||
| INTEGER as sysSRdnFlipSlot | |||
| Integer32 as sysSRdnFlipPort | |||
| DisplayString as sysSRdnFlipCause | |||
| DisplayString as sysSRdnFlipDate | |||
| DisplayString as sysSRdnFlipTime | |||
| SysSBusEntry | |||
| SEQUENCE | |||
| Integer32 as sysSBusPortIdx | |||
| INTEGER as sysSBusStatus | |||
| Integer32 as sysSBusCapturePort | |||
| Integer32 as sysSBusUtilization | |||
| SysSRdnCmdEntry | |||
| SEQUENCE | |||
| INTEGER as sysSRdnEnforcedChannel | |||
| SysSAlrEntry | |||
| SEQUENCE | |||
| Integer32 as sysSAlrIdx | |||
| Integer32 as sysSAlrCode | |||
| INTEGER as sysSAlrState | |||
| INTEGER as sysSAlarmMask | |||
| INTEGER as sysSAlarmInvert | |||
| INTEGER as sysSAlarmOnOff | |||
| Integer32 as sysSAlarmCounter | |||
| SysBufferAlrEntry | |||
| SEQUENCE | |||
| Integer32 as sysBufferAlrIdx | |||
| Integer32 as sysBufferAlrCode | |||
| INTEGER as sysBufferAlrState | |||
| INTEGER as sysBufferAlrSlot | |||
| Integer32 as sysBufferAlrPort | |||
| DisplayString as sysBufferAlrDate | |||
| DisplayString as sysBufferAlrTime | |||
| SysCClkSrcEntry | |||
| SEQUENCE | |||
| Integer32 as sysCClkCnfgIdx | |||
| INTEGER as sysCClkSrcIdx | |||
| INTEGER as sysCClkSrcMode | |||
| Integer32 as sysCClkSrcPrt | |||
| INTEGER as sysCClkStationFreq | |||
| Integer32 as sysCClkRevertiveTimeout | |||
| INTEGER as sysCClkStationIf | |||
| SysCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as sysCnfgIdx | |||
| INTEGER as sysCMatrixMode | |||
| INTEGER as sysCIsdnFormat | |||
| INTEGER as sysCRoutingOnEth | |||
| INTEGER as sysCAutoConfigEnable | |||
| INTEGER as sysCIntTsAllocMode | |||
| SysCRdnEntry | |||
| SEQUENCE | |||
| Integer32 as sysCRdnCnfgIdx | |||
| INTEGER as sysCRdnPrimeSlot | |||
| Integer32 as sysCRdnPrimePort | |||
| INTEGER as sysCRdnSecSlot | |||
| Integer32 as sysCRdnSecPort | |||
| INTEGER as sysCRdnMode | |||
| INTEGER as sysCRdnRecMode | |||
| Integer32 as sysCRdnRecTime | |||
| INTEGER as sysCRdnHwSwFlip | |||
| RowStatus as sysCRdnRowStatus | |||
| INTEGER as sysCRdnOnline | |||
| INTEGER as sysCRdnSwitchingMode | |||
| Integer32 as sysCRdnFlipUponEvent | |||
| Integer32 as sysCRdnLosOrLofTime | |||
| Integer32 as sysCRdnEventsTimeWindow | |||
| Integer32 as sysCRdnSequenceNumberThreshold | |||
| Integer32 as sysCRdnBufferErrorsThreshold | |||
| Integer32 as sysCRdnBuffUnderrunTime | |||
| SysDbaseFlipEntry | |||
| SEQUENCE | |||
| Integer32 as sysDbaseFlipIdx | |||
| DisplayString as sysDbaseFlipTime | |||
| INTEGER as sysDbaseFlipActivation | |||
| MdlSEntry | |||
| SEQUENCE | |||
| INTEGER as mdlSSltIdx | |||
| INTEGER as mdlSCardType | |||
| DisplayString as mdlSHwVer | SIZE(0..255) | ||
| DisplayString as mdlSSwVer | SIZE(0..255) | ||
| INTEGER as mdlSAlarmStatus | |||
| INTEGER as mdlSAlarmStatusAll | |||
| INTEGER as mdlSTestStatus | |||
| INTEGER as mdlSHwStatus | |||
| INTEGER as mdlSActivity | |||
| INTEGER as mdlSAlrClearCmd | |||
| INTEGER as mdlSAlrClearAllCmd | |||
| INTEGER as mdlSAlrMaskAll | |||
| Integer32 as mdlSCmd | |||
| INTEGER as mdlSReset | |||
| INTEGER as mdlSRebuildFrame | |||
| MdlCEntry | |||
| SEQUENCE | |||
| Integer32 as mdlCConfigIdx | |||
| INTEGER as mdlCSlotIdx | |||
| INTEGER as mdlCProgCardType | |||
| Integer32 as mdlCNoOfExtPrt | |||
| Integer32 as mdlCNoOfIntPrt | |||
| Integer32 as mdlCParam | |||
| MdlAlrEntry | |||
| SEQUENCE | |||
| INTEGER as mdlAlrSltIdx | |||
| Integer32 as mdlAlrIdx | |||
| Integer32 as mdlAlrCode | |||
| INTEGER as mdlAlrState | |||
| INTEGER as mdlAlarmMask | |||
| INTEGER as mdlAlarmInvert | |||
| INTEGER as mdlAlarmOnOff | |||
| Integer32 as mdlAlarmCounter | |||
| MdlAlrMaskEntry | |||
| SEQUENCE | |||
| INTEGER as mdlAlrMaskSltIdx | |||
| OCTET STRING as mdlAlrMask | |||
| MdlClEntry | |||
| SEQUENCE | |||
| INTEGER as mdlClIdx | |||
| Integer32 as mdlClSwchStatus | |||
| DisplayString as mdlClLastFlipDate | |||
| DisplayString as mdlClLastFlipTime | |||
| DisplayString as mdlClLastFlipCause | |||
| MdlPsEntry | |||
| SEQUENCE | |||
| INTEGER as mdlPsIdx | |||
| INTEGER as mdlPsStatus | |||
| INTEGER as mdlPsTestResult | |||
| PrtGenEntry | |||
| SEQUENCE | |||
| Integer32 as prtGenPrtIdx | |||
| INTEGER as prtGenSlt | |||
| INTEGER as prtGenExtInt | |||
| Integer32 as prtGenIfIndex | |||
| INTEGER as prtGenActiveStatus | |||
| INTEGER as prtGenAlrStatus | |||
| INTEGER as prtGenTestStatus | |||
| Integer32 as prtGenTestMask | |||
| Integer32 as prtGenTestCmd | |||
| Integer32 as prtGenTestRunning | |||
| INTEGER as prtGenType | |||
| DisplayString as prtGenInterfaceType | SIZE(0..255) | ||
| INTEGER as prtGenAlrClearCmd | |||
| INTEGER as prtGenAlrMaskAll | |||
| OCTET STRING as prtGenParamStatus | |||
| INTEGER as prtGenRdnStatus | |||
| OCTET STRING as prtGenTestMaskXP | |||
| OCTET STRING as prtGenTestCmdXP | |||
| OCTET STRING as prtGenTestRunningXP | |||
| PrtGenTestDurationEntry | |||
| SEQUENCE | |||
| Integer32 as prtGenTestPrtIdx | |||
| INTEGER as prtGenTestIdx | |||
| Integer32 as prtGenTestDuration | |||
| PrtGenTsEntry | |||
| SEQUENCE | |||
| Integer32 as prtGenTsCnfgIdx | |||
| Integer32 as prtGenTsPrtIdx | |||
| Integer32 as prtGenTsIdx | |||
| INTEGER as prtGenTsType | |||
| Integer32 as prtGenTsIConPrt | |||
| Integer32 as prtGenTsIConTs | |||
| PrtSAlarmEntry | |||
| SEQUENCE | |||
| Integer32 as prtSAlarmPrtIdx | |||
| Integer32 as prtSAlarmIdx | |||
| Integer32 as prtSAlarmCode | |||
| INTEGER as prtSAlarmState | |||
| INTEGER as prtSAlarmMask | |||
| INTEGER as prtSAlarmInvert | |||
| INTEGER as prtSAlarmOnOff | |||
| Integer32 as prtSAlarmCounter | |||
| PrtAlrMaskEntry | |||
| SEQUENCE | |||
| Integer32 as prtAlrMaskPrtIdx | |||
| OCTET STRING as prtAlrMask | |||
| PrtBertEntry | |||
| SEQUENCE | |||
| Integer32 as prtBertPrtIdx | |||
| INTEGER as prtBertPattern | |||
| INTEGER as prtBertInjectRate | |||
| INTEGER as prtBertInjectErrRateCmd | |||
| INTEGER as prtBertInjectSingleErrCmd | |||
| Integer32 as prtBertRunTime | |||
| Integer32 as prtBertESs | |||
| Integer32 as prtBertSyncLoss | |||
| Integer32 as prtBertErrorBits | |||
| INTEGER as prtBertClearCounters | |||
| INTEGER as prtBertSyncStatus | |||
| OCTET STRING as prtBertTs | |||
| DisplayString as prtBertResult | SIZE(0..255) | ||
| PrtMonEntry | |||
| SEQUENCE | |||
| Integer32 as prtMonCnfgIdx | |||
| Integer32 as prtMonitoringIdx | |||
| INTEGER as prtMonitoringEnable | |||
| OCTET STRING as prtMonitoringTSs | |||
| Integer32 as prtMonitoredPort | |||
| OCTET STRING as prtMonitoredTSs | |||
| PrtCfgParamEntry | |||
| SEQUENCE | |||
| Integer32 as prtCfgParamCnfgIdx | |||
| Integer32 as prtCfgParamIdx | |||
| INTEGER as prtCfgParamSlt | |||
| INTEGER as prtCfgParamOperatedMl | |||
| INTEGER as prtCfgParamMlAtoMlBPrio | |||
| INTEGER as prtCfgParamMlBtoMlAPrio | |||
| INTEGER as prtCfgParamInbandLoopDetection | |||
| PrtT1E1StatEntry | |||
| SEQUENCE | |||
| Integer32 as prtT1E1SPrtIdx | |||
| INTEGER as prtT1E1SSlt | |||
| Gauge32 as prtT1E1OosCount | |||
| Gauge32 as prtT1E1BpvLastMin | |||
| Gauge32 as prtT1E1BpvMax | |||
| PrtT1E1CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtT1E1CnfgIdx | |||
| Integer32 as prtT1E1PrtIdx | |||
| INTEGER as prtT1E1Slt | |||
| INTEGER as prtT1E1LineType | |||
| INTEGER as prtT1E1LineCode | |||
| INTEGER as prtT1E1SignalMode | |||
| INTEGER as prtT1E1Fdl | |||
| INTEGER as prtT1E1FdlMode | |||
| INTEGER as prtT1E1Sync | |||
| INTEGER as prtT1E1CGA | |||
| OCTET STRING as prtT1E1IdleCode | |||
| INTEGER as prtT1E1OosSignal | |||
| OCTET STRING as prtT1E1VoiceOos | |||
| OCTET STRING as prtT1E1DataOos | |||
| INTEGER as prtT1E1LineLengthMask | |||
| INTEGER as prtT1E1TxGainMask | |||
| INTEGER as prtT1E1InbandMng | |||
| INTEGER as prtT1E1InbandMngRate | |||
| Integer32 as prtT1E1DedicatedTs | |||
| INTEGER as prtT1E1InbandMngRoutProt | |||
| INTEGER as prtT1E1LinkMode | |||
| INTEGER as prtT1E1Multiplier | |||
| INTEGER as prtT1E1RxGain | |||
| INTEGER as prtT1E1RAI | |||
| INTEGER as prtT1E1LineMode | |||
| OCTET STRING as prtT1E1TS0SaBits | |||
| INTEGER as prtT1E1ConnectedTS | |||
| INTEGER as prtT1E1Ts0SaBit | |||
| INTEGER as prtT1E1SameFeCnfg | |||
| INTEGER as prtT1E1RemCrc4 | |||
| Integer32 as prtT1E1MaxTSs | |||
| INTEGER as prtT1E1EocTsConfig | |||
| PrtT1E1FdlMsgEntry | |||
| SEQUENCE | |||
| Integer32 as prtT1E1FdlMsgPrtIdx | |||
| INTEGER as prtT1E1FdlMsgFdlType | |||
| INTEGER as prtT1E1FdlMsgSlt | |||
| OCTET STRING as prtT1E1FdlMsg | |||
| PrtHSParamEntry | |||
| SEQUENCE | |||
| Integer32 as prtHSCnfgIdx | |||
| Integer32 as prtHSPrtIdx | |||
| INTEGER as prtHSSlt | |||
| INTEGER as prtHSRate | |||
| INTEGER as prtHSFifoSize | |||
| INTEGER as prtHSClkMode | |||
| INTEGER as prtHSCTS | |||
| INTEGER as prtHSRtsState | |||
| INTEGER as prtHSInbandLoopback | |||
| INTEGER as prtHSInbandLoopPatternCfg | |||
| DisplayString as prtHSInbandLoopActPattern | |||
| DisplayString as prtHSInbandLoopDeactPattern | |||
| INTEGER as prtHSDCD | |||
| PrtHSBertEntry | |||
| SEQUENCE | |||
| Integer32 as prtHSBertPrtIdx | |||
| INTEGER as prtHSBertSlt | |||
| INTEGER as prtHSBertCountClr | |||
| Integer32 as prtHSBertTestResult | |||
| PrtSpCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtSpCnfgIdx | |||
| Integer32 as prtSpPrtIdx | |||
| INTEGER as prtSpUsage | |||
| INTEGER as prtSpRate | |||
| INTEGER as prtSpDataBits | |||
| INTEGER as prtSpParity | |||
| INTEGER as prtSpCallOutMode | |||
| INTEGER as prtSpInterface | |||
| INTEGER as prtSpCTS | |||
| INTEGER as prtSpDcdDelay | |||
| INTEGER as prtSpDsr | |||
| Integer32 as prtSpNoOfRetries | |||
| INTEGER as prtSpWaitForConnect | |||
| INTEGER as prtSpDialMode | |||
| INTEGER as prtSpAltNumMode | |||
| DisplayString as prtSpPrimaryNum | |||
| DisplayString as prtSpAltNum | |||
| INTEGER as prtSpRoutProtocol | |||
| OCTET STRING as prtSpCmd | |||
| INTEGER as prtSpActCallOut | |||
| INTEGER as prtSpAlrRelayMode | |||
| INTEGER as prtSpStopBits | |||
| PrtDimCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtDimCnfgIdx | |||
| Integer32 as prtDimIdx | |||
| INTEGER as prtDimTxMode | |||
| INTEGER as prtDimPolarity | |||
| INTEGER as prtDimClkMode | |||
| INTEGER as prtDimMaxDelay | |||
| INTEGER as prtDimMng | |||
| PrtDimDestEntry | |||
| SEQUENCE | |||
| Integer32 as prtDestCnfgIdx | |||
| Integer32 as prtDestDimIdx | |||
| Integer32 as prtDestIdx | |||
| Integer32 as prtDest | |||
| INTEGER as prtDestConnect | |||
| PrtICnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtICnfgIdx | |||
| Integer32 as prtIIdx | |||
| INTEGER as prtIRate | |||
| INTEGER as prtIConnect | |||
| PrtHdslEntry | |||
| SEQUENCE | |||
| Integer32 as prtHdslIdx | |||
| INTEGER as prtHdslMode | |||
| INTEGER as prtHdslRptrType | |||
| INTEGER as prtHdslMaxRate | |||
| INTEGER as prtHdslLinkType | |||
| DisplayString as prtHdslCompSwVer | |||
| DisplayString as prtHdslCompHwVer | |||
| PrtT3E3CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtT3E3CnfgIdx | |||
| Integer32 as prtT3E3PrtIdx | |||
| INTEGER as prtT3E3Slt | |||
| INTEGER as prtT3E3LineLength | |||
| INTEGER as prtT3E3InbandMng | |||
| INTEGER as prtT3E3AisFrame | |||
| INTEGER as prtT3E3TxClockSource | |||
| INTEGER as prtT3E3RoutProt | |||
| CmprEntry | |||
| SEQUENCE | |||
| Integer32 as cmprTypeIdx | |||
| Integer32 as cmprCnfgIdx | |||
| Integer32 as cmprVersion | |||
| INTEGER as cmprSltIdx | |||
| Integer32 as cmprPrtIdx | |||
| OCTET STRING as cmprObj | |||
| MapLinkEntry | |||
| SEQUENCE | |||
| Integer32 as mapLinkIdx | |||
| INTEGER as mapLinkSlotIdx | |||
| Integer32 as mapLinkPortIdx | |||
| INTEGER as mapLinkState | |||
| AlrGenEntry | |||
| SEQUENCE | |||
| Integer32 as alrGenCode | |||
| DisplayString as alrGenDescription | SIZE(0..255) | ||
| INTEGER as alrGenLevel | |||
| INTEGER as alrGenSlotType | |||
| INTEGER as alrGenSeverity | |||
| Integer32 as alrGenDebounce | |||
| INTEGER as alrGenDefSeverity | |||
| SysGenKmuxEntry | |||
| SEQUENCE | |||
| Integer32 as sysGenConfigIdx | |||
| INTEGER as sysGenFlipIntegration | |||
| INTEGER as sysGenMlMode | |||
| INTEGER as sysGenFaType | |||
| INTEGER as sysGenLinkRecovery | |||
| INTEGER as sysGenLinkSourceClock | |||
| Integer32 as sysGenMngBwA | |||
| Integer32 as sysGenMngBwB | |||
| Integer32 as sysGenAutoDialSlot | |||
| INTEGER as sysGenResetBypassEnable | |||
| SysBackupEntry | |||
| SEQUENCE | |||
| Integer32 as sysBackupConfigIdx | |||
| INTEGER as sysBackupDatabase | |||
| INTEGER as sysBackupMode | |||
| INTEGER as sysBackupDialTimeout | |||
| INTEGER as sysBackupOptions | |||
| SysBackupAgendaEntry | |||
| SEQUENCE | |||
| INTEGER as sysBackupCfgIdx | |||
| INTEGER as sysBackupDay | |||
| INTEGER as sysBackupZone | |||
| DisplayString as sysBackupEndTime | |||
| INTEGER as sysBackupStatus | |||
| SysFrameAllocationEntry | |||
| SEQUENCE | |||
| Integer32 as sysFaConfigIdx | |||
| INTEGER as sysFaLink | |||
| Integer32 as sysFaPrt | |||
| Integer32 as sysFaStartingBit | |||
| Integer32 as sysFaNumOfBits | |||
| SysDisconnectSupervisionEventEntry | |||
| SEQUENCE | |||
| Integer32 as sysDsEventIdx | |||
| INTEGER as sysDsEventSlot | |||
| Integer32 as sysDsEventTS | |||
| DisplayString as sysDsEventDescr | |||
| DisplayString as sysDsEventDateAndTime | |||
| MdlKmxEntry | |||
| SEQUENCE | |||
| Integer32 as mdlKmxConfigIdx | |||
| INTEGER as mdlKmxSlotIdx | |||
| INTEGER as mdlKmxOperatedMl | |||
| INTEGER as mdlKmxMlAtoMlBPrio | |||
| INTEGER as mdlKmxMlBtoMlAPrio | |||
| INTEGER as mdlKmxOutSrvMethod | |||
| INTEGER as mdlKmxV54Config | |||
| INTEGER as mdlKmxTiming | |||
| MdlKvf5PbxEntry | |||
| SEQUENCE | |||
| Integer32 as mdlKvf5PbxConfigIdx | |||
| INTEGER as mdlKvf5PbxSlotIdx | |||
| INTEGER as mdlKvf5PbxSig | |||
| INTEGER as mdlKvf5PbxSigMode | |||
| INTEGER as mdlKvf5PbxTsAssign | |||
| Integer32 as mdlKvf5PbxCcsTs | |||
| INTEGER as mdlKvf5PbxOos | |||
| INTEGER as mdlKvf5PbxSigTxPbx | |||
| INTEGER as mdlKvf5PbxSigRxPbx | |||
| OCTET STRING as mdlKvf5PbxDefABCD | |||
| INTEGER as mdlKvf5PbxFramerSlot | |||
| INTEGER as mdlKvf5PbxCcsRate | |||
| OCTET STRING as mdlKvf5PbxTxAbcdBit | |||
| INTEGER as mdlKvf5PbxHdlcCrc | |||
| MdlDisconnectSupervisionEntry | |||
| SEQUENCE | |||
| Integer32 as mdlDsConfigIdx | |||
| INTEGER as mdlDsSlotIdx | |||
| INTEGER as mdlDs | |||
| INTEGER as mdlDsUserLoc | |||
| INTEGER as mdlDsMode | |||
| Integer32 as mdlDsSilence | |||
| OCTET STRING as mdlDsClrFwSig | |||
| OCTET STRING as mdlDsAnswerSig | |||
| OCTET STRING as mdlDsClrBwSig | |||
| Integer32 as mdlDsFbtLowFreq | |||
| Integer32 as mdlDsFbtHighFreq | |||
| Integer32 as mdlDsFbtTimeOn1 | |||
| Integer32 as mdlDsFbtTimeOff1 | |||
| Integer32 as mdlDsFbtTimeOn2 | |||
| Integer32 as mdlDsFbtTimeOff2 | |||
| Integer32 as mdlDsFbtLowFreqLevel | |||
| Integer32 as mdlDsFbtHighFreqLevel | |||
| PrtMlFrameStatsEntry | |||
| SEQUENCE | |||
| Integer32 as prtMlFrameIdx | |||
| INTEGER as prtMlFrameSlt | |||
| INTEGER as prtMlBitWeight | |||
| Integer32 as prtMlDataUsage | |||
| Integer32 as prtMlControlSig | |||
| Integer32 as prtMlDownload | |||
| Integer32 as prtMlSync | |||
| Integer32 as prtMlTotalUsage | |||
| Integer32 as prtMlTotalFree | |||
| PrtMlEntry | |||
| SEQUENCE | |||
| Integer32 as prtMlCnfgIdx | |||
| Integer32 as prtMlIdx | |||
| INTEGER as prtMlSlt | |||
| INTEGER as prtMlTiming | |||
| INTEGER as prtMlBufferSize | |||
| INTEGER as prtMlDsrCts | |||
| INTEGER as prtMlSpeed | |||
| Integer32 as prtMlStartTS | |||
| INTEGER as prtMlBypassTs16 | |||
| INTEGER as prtMlCallMode | |||
| INTEGER as prtMlBondingEnable | |||
| PrtMlIsdnEntry | |||
| SEQUENCE | |||
| Integer32 as prtMlIsdnCnfgIdx | |||
| Integer32 as prtMlIsdnIdx | |||
| INTEGER as prtMlIsdnSlt | |||
| INTEGER as prtMlIsdnMode | |||
| INTEGER as prtMlIsdnStandard | |||
| DisplayString as prtMlIsdnLocSubNum | |||
| DisplayString as prtMlIsdnLocNum | |||
| DisplayString as prtMlIsdnOutSubNum | |||
| DisplayString as prtMlIsdnBackupCallNum | |||
| INTEGER as prtMlIsdnInNumMode | |||
| PrtHsLsEntry | |||
| SEQUENCE | |||
| Integer32 as prtHsLsCnfgIdx | |||
| Integer32 as prtHsLsIdx | |||
| INTEGER as prtHsLsSlt | |||
| INTEGER as prtHsLsCommProtocol | |||
| INTEGER as prtHsLsAsyncDataLen | |||
| INTEGER as prtHsLsTiming | |||
| INTEGER as prtHsLsCtrlSignal | |||
| INTEGER as prtHsLsCts | |||
| INTEGER as prtHsLsRtsCtsDelay | |||
| INTEGER as prtHsLsDsrMode | |||
| INTEGER as prtHsLsSpeed | |||
| INTEGER as prtHsLsUType | |||
| PrtTreMbeEntry | |||
| SEQUENCE | |||
| Integer32 as prtTreMbeCnfgIdx | |||
| Integer32 as prtTreMbeIdx | |||
| INTEGER as prtTreMbeSlt | |||
| INTEGER as prtTreMbeLan | |||
| INTEGER as prtTreMbeLanRate | |||
| INTEGER as prtTreMbeLinkSpeed | |||
| PrtVoiceFaxEntry | |||
| SEQUENCE | |||
| Integer32 as prtVoiceFaxCnfgIdx | |||
| Integer32 as prtVoiceFaxIdx | |||
| INTEGER as prtVoiceFaxSlt | |||
| Integer32 as prtVoiceFaxTransGain | |||
| Integer32 as prtVoiceFaxReceiveGain | |||
| INTEGER as prtVoiceFaxWire | |||
| INTEGER as prtVoiceFaxTimeOut | |||
| INTEGER as prtVoiceFaxEchoCanceler | |||
| INTEGER as prtVoiceFaxSpeed | |||
| INTEGER as prtVoiceFaxMeterRate | |||
| INTEGER as prtVoiceFaxCodingLaw | |||
| INTEGER as prtVoiceFaxOperMode | |||
| OCTET STRING as prtVoiceFaxSigInOutband | |||
| INTEGER as prtVoiceFaxTsGroup | |||
| Integer32 as prtVoiceFaxRxFaxGain | |||
| INTEGER as prtVoiceFaxSigHold | |||
| INTEGER as prtVoiceFaxIfSignaling | |||
| INTEGER as prtVoiceFaxEMTypes | |||
| INTEGER as prtVoiceFaxRingFrequency | |||
| OCTET STRING as prtVoiceFaxSignalingStatus | |||
| SysGenAlarmBuffEntry | |||
| SEQUENCE | |||
| Integer32 as sysGenAlarmBuffIndex | |||
| DisplayString as sysGenAlarmDescr | |||
| SysGenLogEntry | |||
| SEQUENCE | |||
| Integer32 as sysGenLogIndex | |||
| DisplayString as sysGenLogDescr | |||
| SysCallProfileEntry | |||
| SEQUENCE | |||
| Integer32 as sysCallProfileIndex | |||
| INTEGER as sysCallProfileConnectCmd | |||
| INTEGER as sysCallProfileDisconnectCmd | |||
| Integer32 as sysCallProfileIncrBwCmd | |||
| Integer32 as sysCallProfileDecrBwCmd | |||
| PrtCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as prtIndex | |||
| Integer32 as prtCnfgDecrBwChNum | |||
| Integer32 as prtCnfgIncrBwChNum | |||
| INTEGER as prtCnfgDisconnect | |||
| INTEGER as prtCnfgActivateLoop | |||
| INTEGER as prtCnfgClearLoop | |||
| Integer32 as prtCnfgLoopStatus | |||
| ChannelCnfgEntry | |||
| SEQUENCE | |||
| Integer32 as chIndex | |||
| INTEGER as chCnfgUnlock | |||
| INTEGER as chCnfgPing | |||
| ChannelStatEntry | |||
| SEQUENCE | |||
| INTEGER as chStatOperStatus | |||
| AtmNteConfIfEntry | |||
| SEQUENCE | |||
| INTEGER as atmConfIfTransmitClk | |||
| INTEGER as atmConfIfLoopback | |||
| INTEGER as atmConfIfFrameType | |||
| INTEGER as atmConfIfCardType | |||
| INTEGER as atmConfAtmIfVpiVciLimit | |||
| INTEGER as atmConfIfHwFeatures | |||
| Integer32 as atmConfIfOutputRate | |||
| Integer32 as atmConfIfInputRate | |||
| INTEGER as atmConfAlarmForwarding | |||
| AtmNteAlarmIfEntry | |||
| SEQUENCE | |||
| Integer32 as atmInterfaceActiveAlarms | |||
| Integer32 as atmThresholdSectionBIP | |||
| Integer32 as atmThresholdLineBIP | |||
| Integer32 as atmThresholdLineFEBE | |||
| Integer32 as atmThresholdPathBIP | |||
| Integer32 as atmThresholdPathFEBE | |||
| Integer32 as atmThresholdErroredCells | |||
| Integer32 as atmThresholdLostCells | |||
| Integer32 as atmThresholdMisinsertedCells | |||
| INTEGER as atmInterfaceAlarmStatus | |||
| Integer32 as atmInterfaceMaskAlarms | |||
| AtmNteConfVpEntry | |||
| SEQUENCE | |||
| INTEGER as atmConfVpPolicing | |||
| INTEGER as atmConfVpCCAdminStatus | |||
| INTEGER as atmConfVpLoopbackAdminStatus | |||
| OCTET STRING as atmConfVpLoopbackSinkAddress | |||
| OCTET STRING as atmConfVpCongestionControl | |||
| INTEGER as atmConfVpCCDirection | |||
| DateAndTime as atmConfVpCreationTime | |||
| INTEGER as atmConfVpOamSupport | |||
| INTEGER as atmConfVpCCOperStatus | |||
| INTEGER as atmConfVpLoopbackTraffic | |||
| INTEGER as atmConfVpLoopbackFailureInd | |||
| Integer32 as atmConfVpLoopbackFailureThreshold | |||
| INTEGER as atmConfVpOamDirection | |||
| AtmNteAlarmVpEntry | |||
| SEQUENCE | |||
| Integer32 as atmNteVpAlarmVpi | |||
| Integer32 as atmNteVpActiveAlarms | |||
| AtmNteAlarmVcEntry | |||
| SEQUENCE | |||
| Integer32 as atmNteVcAlarmVpi | |||
| Integer32 as atmNteVcAlarmVci | |||
| Integer32 as atmNteVcActiveAlarms | |||