C-PRODUCT-QSIM-MIB

File: C-PRODUCT-QSIM-MIB.mib (25991 bytes)

Imported modules

C-PRODUCT-GROUP-MIB C-PRODUCT-BASE-MIB RFC-1212

Imported symbols

qsim cardSlot portSlot
portNumber vcpSideId OBJECT-TYPE

Defined Objects

qsimCard 1.3.6.1.4.1.43.1.12.3.1.1.12.1
OBJECT IDENTIFIER    

qsimCardTable 1.3.6.1.4.1.43.1.12.3.1.1.12.1.1
Card configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimCardEntry

qsimCardEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.1.1.1
Card configuration entry.
OBJECT-TYPE    
  QsimCardEntry  

qsimCardMaxFrameSize 1.3.6.1.4.1.43.1.12.3.1.1.12.1.1.1.1
Maximum frame size for SDLC, DXI and Frame Relay frames. WARNING: Change of the Maximum Frame Size will cause Disruption of Service provided by the card.
OBJECT-TYPE    
  INTEGER mfs-2kb(1), mfs-4kb(2), mfs-8kb(3)  

qsimPort 1.3.6.1.4.1.43.1.12.3.1.1.12.2
OBJECT IDENTIFIER    

qsimPortTable 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1
QSIM port configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimPortEntry

qsimPortEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1
QSIM port configuration entry. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) can be from 1 to 4.
OBJECT-TYPE    
  QsimPortEntry  

qsimPortLinkType 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.1
Link layer protocol supported by the port.
OBJECT-TYPE    
  INTEGER dxi(1), sdlc(2), frame-relay(3)  

qsimPortCableType 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.2
Type of cable connected to the port.
OBJECT-TYPE    
  INTEGER none(1), dte(2), dce(3)  

qsimPortTermTimingSource 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.3
Terminal timing source. This object applies ONLY when a DCE cable is connected to the port. If cable type is 'none' or 'dce', this object can be read and written. If cable type is 'dte', a get request returns whatever value currently stored in the managed node for this port and a set request returns genErr.
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

qsimPortReceiveTimingPhase 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.4
Receive timing phase control. This object applies ONLY when a DCE cable is connected to the port. If cable type is 'none' or 'dce', this object can be read and written. If cable type is 'dte', a get request returns whatever value currently stored in the managed node for this port and a set request returns genErr.
OBJECT-TYPE    
  INTEGER normal(1), inverted(2)  

qsimPortDataRate 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.5
Data rate supported by the port.
OBJECT-TYPE    
  INTEGER dr-64k(1), dr-128k(2), dr-256k(3), dr-512k(4), dr-1m(5), dr-2m(6), dr-4m(7), dr-8m(8)  

qsimPortMinFlagBytes 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.6
Minimum flag bytes required to distinguish a frame.
OBJECT-TYPE    
  INTEGER fb-1(1), fb-2(2)  

qsimPortFcsSize 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.7
Number of bytes in the FCS field of a frame.
OBJECT-TYPE    
  INTEGER fcs-2(1), fcs-4(2)  

qsimPortRts 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.8
RTS pin status.
OBJECT-TYPE    
  PinStatus  

qsimPortCts 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.9
CTS pin status.
OBJECT-TYPE    
  PinStatus  

qsimPortDcd 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.10
DCD pin status.
OBJECT-TYPE    
  PinStatus  

qsimPortDsr 1.3.6.1.4.1.43.1.12.3.1.1.12.2.1.1.11
DSR pin status.
OBJECT-TYPE    
  PinStatus  

hsimPort 1.3.6.1.4.1.43.1.12.3.1.1.12.3
OBJECT IDENTIFIER    

hsimPortTable 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1
HSIM port configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    HsimPortEntry

hsimPortEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1
HSIM port configuration entry. The slot number (portSlot) of this card can be from 4 to 6. The port number (portNumber) of this card is always 1.
OBJECT-TYPE    
  HsimPortEntry  

hsimPortLinkType 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.1
Link layer protocol supported by the port.
OBJECT-TYPE    
  INTEGER dxi(1), sdlc(2), frame-relay(3)  

hsimPortDceDteMode 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.2
DCE/DTE mode of the port.
OBJECT-TYPE    
  INTEGER dce(1), dte(2)  

hsimPortDataRate 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.3
Data rate supported by the port.
OBJECT-TYPE    
  INTEGER dr-20m(1)  

hsimPortMinFlagBytes 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.4
Minimum flag bytes required to distinguish a frame.
OBJECT-TYPE    
  INTEGER fb-1(1), fb-2(2)  

hsimPortFcsSize 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.5
Number of bytes in the FCS field of a frame.
OBJECT-TYPE    
  INTEGER fcs-2(1), fcs-4(2)  

hsimPortTa 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.6
TA pin status.
OBJECT-TYPE    
  PinStatus  

hsimPortCa 1.3.6.1.4.1.43.1.12.3.1.1.12.3.1.1.7
CA pin status.
OBJECT-TYPE    
  PinStatus  

qsimVc 1.3.6.1.4.1.43.1.12.3.1.1.12.4
OBJECT IDENTIFIER    

qsimSdlcVc 1.3.6.1.4.1.43.1.12.3.1.1.12.4.1
OBJECT IDENTIFIER    

qsimDxiVc 1.3.6.1.4.1.43.1.12.3.1.1.12.4.2
OBJECT IDENTIFIER    

qsimFrameRelayVc 1.3.6.1.4.1.43.1.12.3.1.1.12.4.3
OBJECT IDENTIFIER    

qsimLmi 1.3.6.1.4.1.43.1.12.3.1.1.12.6
OBJECT IDENTIFIER    

qsimLmiTable 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1
LMI configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimLmiEntry

qsimLmiEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1
LMI configuration entry. The slot number (portSlot) should be from 4 to 6. The port number (portNumber) is from 1 to 4 for QSIM card, 1 to 8 for FAM card, and 1 for HSIM card.
OBJECT-TYPE    
  QsimLmiEntry  

qsimLmiProtocol 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.1
LMI protocol supported by the port.
OBJECT-TYPE    
  INTEGER none(1), q-933a(2), t1-617d(3)  

qsimLmiProcedure 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.2
LMI procedure supported by the port. This object applies when LMI Q.933 Annex A or T1.617 Annex D protocol is selected.
OBJECT-TYPE    
  INTEGER user-side(1), network-side(2), bidirectional(3)  

qsimLmiUserT391 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.3
User-side link integrity verification (LIV) polling timer. This object applies when LMI user-side or bidirectional procedure is selected.
OBJECT-TYPE    
  INTEGER 5..180  

qsimLmiUserN391 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.4
User-side full status polling counter. This object applies when LMI user-side or bidirectional procedure is selected.
OBJECT-TYPE    
  INTEGER 1..255  

qsimLmiUserN392 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.5
User-side error threshold. This object applies when LMI user-side or bidirectional procedure is selected. User-side N392 should be less than or equal to user- side N393.
OBJECT-TYPE    
  INTEGER 1..10  

qsimLmiUserN393 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.6
User-side monitored events count. This object applies when LMI user-side or bidirectional procedure is selected.
OBJECT-TYPE    
  INTEGER 1..10  

qsimLmiNetworkT392 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.7
Network-side polling verification timer. This object applies when LMI network-side or bidirectional procedure is selected.
OBJECT-TYPE    
  INTEGER 5..200  

qsimLmiNetworkN392 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.8
Network-side error threshold. This object applies when LMI network-side or bidirectional procedure is selected. Network-side N392 should be less than or equal to Network- side N393.
OBJECT-TYPE    
  INTEGER 1..10  

qsimLmiNetworkN393 1.3.6.1.4.1.43.1.12.3.1.1.12.6.1.1.9
Network-side monitored events count. This object applies when LMI network-side or bidirectional procedure is selected.
OBJECT-TYPE    
  INTEGER 1..10  

qsimNewVc 1.3.6.1.4.1.43.1.12.3.1.1.12.9
OBJECT IDENTIFIER    

qsimNewSdlcVc 1.3.6.1.4.1.43.1.12.3.1.1.12.9.1
OBJECT IDENTIFIER    

qsimNewSdlcVcTable 1.3.6.1.4.1.43.1.12.3.1.1.12.9.1.1
SDLC VC configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimNewSdlcVcEntry

qsimNewSdlcVcEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.9.1.1.1
SDLC VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to maxslots. The port number (vcPortPort) can be from 1 to 4.
OBJECT-TYPE    
  QsimNewSdlcVcEntry  

qsimNewSdlcVcShapper 1.3.6.1.4.1.43.1.12.3.1.1.12.9.1.1.1.1
Data rate supported by the SDLC VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate data rate shapper number --------- --------- -------------- 1.5m 64k 1 3m 128k 2 4.5m 192k 3 6m 256k 4 7.5m 384k 5 9m 512k 6 10.5m 640k 7 12m 768k 8 13.5m 1m 9 15m 1.5m 10 16.5m 2m 11 18m 4m 12 20m 8m 13
OBJECT-TYPE    
  INTEGER 1..13  

qsimNewDxiVc 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2
OBJECT IDENTIFIER    

qsimNewDxiVcTable 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1
DXI VC configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimNewDxiVcEntry

qsimNewDxiVcEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1.1
DXI VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to 6. The port number (vcPortPort) can be from 1 to 4.
OBJECT-TYPE    
  QsimNewDxiVcEntry  

qsimNewDxiVcDfaVpi 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1.1.1
DXI DFA VPI.
OBJECT-TYPE    
  INTEGER 0..15  

qsimNewDxiVcDfaVci 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1.1.2
DXI DFA VCI.
OBJECT-TYPE    
  INTEGER 0..63  

qsimNewDxiVcDfaVciRange 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1.1.3
DXI VCI range. This object is used to create a set of VCs whose VPI equals to the value of the instance of qsimDxiVcDfaVpi and whose VCIs are in the range FROM 'the value of the instance of qsimDxiVcDfaVci' TO 'the value of the instance of this object PLUS the value of the instance of qsiDxiVcDfaVci MINUS 1'. A successful set request will generate 1 to N VC entries in this table. Where N equals to the value of the instance of this object. A get request always returns 1.
OBJECT-TYPE    
  INTEGER 1..64  

qsimNewDxiVcShapper 1.3.6.1.4.1.43.1.12.3.1.1.12.9.2.1.1.4
Data rate supported by the DXI VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate data rate shapper number --------- --------- -------------- 1.5m 64k 1 3m 128k 2 4.5m 192k 3 6m 256k 4 7.5m 384k 5 9m 512k 6 10.5m 640k 7 12m 768k 8 13.5m 1m 9 15m 1.5m 10 16.5m 2m 11 18m 4m 12 20m 8m 13
OBJECT-TYPE    
  INTEGER 1..13  

qsimNewFrameRelayVc 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3
OBJECT IDENTIFIER    

qsimNewFrameRelayVcTable 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1
Frame relay VC configuration table.
OBJECT-TYPE    
  SEQUENCE OF  
    QsimNewFrameRelayVcEntry

qsimNewFrameRelayVcEntry 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1
Frame relay VC configuration entry. The slot number (vcPortSlot) of the VC can be from 4 to maxslots. The port number (vcPortPort) can be from 1 to 4.
OBJECT-TYPE    
  QsimNewFrameRelayVcEntry  

qsimNewFrameRelayVcInterworking 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.1
Frame Relay/ATM interworking mode.
OBJECT-TYPE    
  INTEGER network(1), service(2)  

qsimNewFrameRelayVcEncapsulation 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.2
Encapsulation type. This object applies ONLY to service interworking.
OBJECT-TYPE    
  INTEGER transparent(1), translation(2)  

qsimNewFrameRelayVcDe2Clp 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.3
If mode 1 mapping is desirable, the user shall select direct mapping. If mode 2 mapping is desirable, the user shall select always-0 or always-1 to map the CLP field to a constant value (0 or 1).
OBJECT-TYPE    
  INTEGER direct(1), always-0(2), always-1(3)  

qsimNewFrameRelayVcClp2De 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.4
For network interworking - The options are none and direct. If mode 1 mapping is desirable, the user shall select direct mapping. If mode 2 mapping is desirable, the user shall select none. The none option maps the DE field in FR-SSCS PDU to the core-Q.922 frame DE field and ignores the CLP field in the ATM cells. For service interworking - The options are direct, always-0 and always-1. If mode 1 mapping is desirable, the user shall select direct mapping. If mode 2 mapping is desirable, the user shall select always-0 or always-1 to map the DE field to a constant value (0 or 1).
OBJECT-TYPE    
  INTEGER none(1), direct(2), always-0(3), always-1(4)  

qsimNewFrameRelayVcFecnToEfci 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.5
This object applies ONLY to service interworking. If mode 1 mapping is desirable, direct mapping should be selected. If mode 2 mapping is desirable, always-0 should be selected to set the EFCI field to 'congestion not experienced'.
OBJECT-TYPE    
  INTEGER direct(1), always-0(2)  

qsimNewFrameRelayVcShapper 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.6
Data rate supported by the frame relay VC. Depending on the type of card a VC is configured, the shapper numbers are assigned as follows: HSIM QSIM data rate data rate shapper number --------- --------- -------------- 1.5m 64k 1 3m 128k 2 4.5m 192k 3 6m 256k 4 7.5m 384k 5 9m 512k 6 10.5m 640k 7 12m 768k 8 13.5m 1m 9 15m 1.5m 10 16.5m 2m 11 18m 4m 12 20m 8m 13
OBJECT-TYPE    
  INTEGER 1..13  

qsimNewFrameRelayVcDlci 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.7
Frame relay DLCI.
OBJECT-TYPE    
  INTEGER 16..991  

qsimNewFrameRelayVcFrSscsDlci 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.8
This object applies ONLY to network interworking. Its valid value is 16..991 and 1022.
OBJECT-TYPE    
  INTEGER  

qsimNewFrameRelayVcStatus 1.3.6.1.4.1.43.1.12.3.1.1.12.9.3.1.1.9
Frame relay PVC operational status.
OBJECT-TYPE    
  INTEGER out-of-service(1), in-service(2), not-configured(3)  

Defined Objects

PinStatus  
INTEGER off(1), on(2)    

QsimCardEntry  
SEQUENCE    
  INTEGER as qsimCardMaxFrameSize  

QsimPortEntry  
SEQUENCE    
  INTEGER as qsimPortLinkType  
  INTEGER as qsimPortCableType  
  INTEGER as qsimPortTermTimingSource  
  INTEGER as qsimPortReceiveTimingPhase  
  INTEGER as qsimPortDataRate  
  INTEGER as qsimPortMinFlagBytes  
  INTEGER as qsimPortFcsSize  
  PinStatus as qsimPortRts  
  PinStatus as qsimPortCts  
  PinStatus as qsimPortDcd  
  PinStatus as qsimPortDsr  

HsimPortEntry  
SEQUENCE    
  INTEGER as hsimPortLinkType  
  INTEGER as hsimPortDceDteMode  
  INTEGER as hsimPortDataRate  
  INTEGER as hsimPortMinFlagBytes  
  INTEGER as hsimPortFcsSize  
  PinStatus as hsimPortTa  
  PinStatus as hsimPortCa  

QsimLmiEntry  
SEQUENCE    
  INTEGER as qsimLmiProtocol  
  INTEGER as qsimLmiProcedure  
  INTEGER as qsimLmiUserT391  
  INTEGER as qsimLmiUserN391  
  INTEGER as qsimLmiUserN392  
  INTEGER as qsimLmiUserN393  
  INTEGER as qsimLmiNetworkT392  
  INTEGER as qsimLmiNetworkN392  
  INTEGER as qsimLmiNetworkN393  

QsimNewSdlcVcEntry  
SEQUENCE    
  INTEGER as qsimNewSdlcVcShapper  

QsimNewDxiVcEntry  
SEQUENCE    
  INTEGER as qsimNewDxiVcDfaVpi  
  INTEGER as qsimNewDxiVcDfaVci  
  INTEGER as qsimNewDxiVcDfaVciRange  
  INTEGER as qsimNewDxiVcShapper  

QsimNewFrameRelayVcEntry  
SEQUENCE    
  INTEGER as qsimNewFrameRelayVcInterworking  
  INTEGER as qsimNewFrameRelayVcEncapsulation  
  INTEGER as qsimNewFrameRelayVcDe2Clp  
  INTEGER as qsimNewFrameRelayVcClp2De  
  INTEGER as qsimNewFrameRelayVcFecnToEfci  
  INTEGER as qsimNewFrameRelayVcShapper  
  INTEGER as qsimNewFrameRelayVcDlci  
  INTEGER as qsimNewFrameRelayVcFrSscsDlci  
  INTEGER as qsimNewFrameRelayVcStatus