
CISCO-LWAPP-CLIENT-ROAMING-MIB
File:
CISCO-LWAPP-CLIENT-ROAMING-MIB.mib (27374 bytes)
Imported modules
Imported symbols
Defined Objects
| ciscoLwappClRoamMIB |
1.3.6.1.4.1.9.9.523 |
| This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is for CCX related features as specified in the CCX specifications. This MIB covers roaming RF parameters for CCX clients. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Basic Service Set ( BSS ) The IEEE 802.11 BSS of an AP comprises of the stations directly associating with the AP. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Cisco Compatible eXtensions (CCX) Wireless LAN Access Points (APs) manufactured by Cisco Systems have features and capabilities beyond those in related standards (e.g., IEEE 802.11 suite of standards ,Wi-Fi recommendations by WECA, 802.1X security suite,etc). A number of features provide higher performance.For example, Cisco AP transmits a specific Information Element, which the clients adapt to for enhanced performance. Similarly, a number of features are implemented by means of proprietary Information Elements, which Cisco clients use in specific ways to carry out tasks above and beyond the standard. Other examples of feature categories are roaming and power saving. Client Roaming A client may decide to reassociate with another AP for reasons of its own choosing. The decision of whether or not to use the information contained in the AP list is up to the discretion of the implementor, as long as the roam time requirement is met. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol |
| MODULE-IDENTITY |
|
|
|
| clcrDot11aHysteresis |
1.3.6.1.4.1.9.9.523.1.1.3 |
| This object indicates how much stronger the signal strength (dB) of a neighbor AP must be, in order for the client to roam to it. The use of roaming hysteresis is intended to reduce the amount of clients roaming back and forth between BSSs if the client is physically located on or near the border between two BSSs. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
2..4 |
|
| clcrDot11aAdaptiveScanThreshold |
1.3.6.1.4.1.9.9.523.1.1.4 |
| This object configures the threshold for the strength of the signals received(RSSI) from an AP, as seen by an associated client, below which the client must be able to roam to a neighbor AP within the specified Transition Time configured through clcrDot11aTransitionTime. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
-77..-70 |
|
| clcrDot11aTransitionTime |
1.3.6.1.4.1.9.9.523.1.1.5 |
| This object configures the maximum time duration permitted for the client to detect a suitable neighbor AP to roam to and to complete the roam, whenever the RSSI from the client?s associated AP is below the adaptive scan threshold configured through clcrDot11aAdaptiveScanThreshold. The time is expressed in 100th of a second. |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
100..10000 |
|
| clcrDot11bHysteresis |
1.3.6.1.4.1.9.9.523.1.2.3 |
| This object indicates how much stronger the signal strength (dB) of a neighbor AP must be, in order for the client to roam to it. The use of roaming hysteresis is intended to reduce the amount of clients roaming back and forth between BSSs if the client is physically located on or near the border between two BSSs. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
2..4 |
|
| clcrDot11bAdaptiveScanThreshold |
1.3.6.1.4.1.9.9.523.1.2.4 |
| This object configures the threshold for the strength of the signals received(RSSI) from an AP, as seen by an associated client, below which the client must be able to roam to a neighbor AP within the specified Transition Time configured through clcrDot11bTransitionTime. |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
-77..-70 |
|
| clcrDot11bTransitionTime |
1.3.6.1.4.1.9.9.523.1.2.5 |
| This object configures the maximum time duration permitted for the client to detect a suitable neighbor AP to roam to and to complete the roam, whenever the RSSI from the client is associated AP is below the adaptive scan threshold configured through clcrDot11aAdaptiveScanThreshold. The time is expressed in 100th of a second. |
| OBJECT-TYPE |
|
|
|
| |
TimeInterval |
100..10000 |
|
| clcrRoamReasonReportTable |
1.3.6.1.4.1.9.9.523.1.3.1 |
| This table provides the reasons for CCX clients roaming from one AP to another. When a CCX client associates to an AP, it will always send an IAPP information packet to the new AP listing the characteristics of the previous AP. An entry is added to this table when a roam reason report is sent by a CCX client when it roams to a new AP. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
ClcrRoamReasonReportEntry |
|
| clcrRoamReasonReportEntry |
1.3.6.1.4.1.9.9.523.1.3.1.1 |
| Each entry corresponds to the roam reason report sent by a CCX client to the new AP to which client associates. |
| OBJECT-TYPE |
|
|
|
| |
ClcrRoamReasonReportEntry |
|
|
| clcrRoamClientTimeStamp |
1.3.6.1.4.1.9.9.523.1.3.1.1.2 |
| This object indicates the time instance at which this report was received by the new AP, to which client roamed to. This represents number of seconds elapsed since 00:00:00 on January 1, 1970, Coordinated Universal Time (UTC). So a value of '1131362704' means 'Mon Nov 7 16:55:04 2005'. |
| OBJECT-TYPE |
|
|
|
| |
TimeTicks |
|
|
| clcrRoamPrevApSsid |
1.3.6.1.4.1.9.9.523.1.3.1.1.6 |
| This object indicates the SSID at which the client was associated to the previous AP. |
| OBJECT-TYPE |
|
|
|
| |
OCTET STRING |
SIZE(1..32) |
|
| clcrRoamReason |
1.3.6.1.4.1.9.9.523.1.3.1.1.8 |
| This object indicates the reason for a client to roam to a new AP. The semantics are as follows. clcrUnspecified - The reason is not known or can't be found. clcrPoorLink - Normal roam due to poor link (excessive retries, too much interference, RSSI too low, etc.) clcrLoadBalancing - Normal roam due to load balancing clcrInsufficientCapacity - Roaming occured due to the insufficient capacity on the previous AP (TSPEC rejected) clcrDirectedRoam - Roaming is directed by the 802.11 wireless Infrastructure clcrFirstAssociation - This is the first association to a particular WLAN clcrRoamingIn - Roaming in from cellular or other WAN clcrRoamingOut - Roaming out to cellular or other WAN clcrBetterAp - Normal roam due to better AP found clcrDisassociated - Deauthenticated or Disassociated from the previous AP. |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
clcrUnspecified(0), clcrPoorLink(1), clcrLoadBalancing(2), clcrInsufficientCapacity(3), clcrDirectedRoam(4), clcrFirstAssociation(5), clcrRoamingIn(6), clcrRoamingOut(7), clcrBetterAp(8), clcrDisassociated(9) |
|
| clcrDot11StatsTable |
1.3.6.1.4.1.9.9.523.1.4.1 |
| This table populates the statistics collected when the client roamed in the WLAN. There exists a row in this table for each conceptual row in cLApDot11IfTable that represents a dot11 interface of an AP. |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
ClcrDot11StatsEntry |
|
| clcrDot11StatsEntry |
1.3.6.1.4.1.9.9.523.1.4.1.1 |
| Each entry represents a conceptual row in clcrDot11StatsTable and corresponds to the roam reason report sent by a CCX client to the new AP which the client associates to. |
| OBJECT-TYPE |
|
|
|
| |
ClcrDot11StatsEntry |
|
|
Defined Objects
| ClcrRoamReasonReportEntry |
|
| SEQUENCE |
|
|
|
| |
MacAddress as clcrRoamClientMacAddress |
|
|
| |
TimeTicks as clcrRoamClientTimeStamp |
|
|
| |
MacAddress as clcrRoamNewApMacAddress |
|
|
| |
MacAddress as clcrRoamPrevApMacAddress |
|
|
| |
CLDot11Channel as clcrRoamPrevApChannel |
|
|
| |
OCTET STRING as clcrRoamPrevApSsid |
|
|
| |
TimeInterval as clcrRoamDisassocTimeInterval |
|
|
| |
INTEGER as clcrRoamReason |
|
|
| ClcrDot11StatsEntry |
|
| SEQUENCE |
|
|
|
| |
Counter32 as clcrDot11NeighborRequestRx |
|
|
| |
Counter32 as clcrDot11NeighborReplySent |
|
|
| |
Counter32 as clcrDot11RoamReasonReportRx |
|
|
| |
Counter32 as clcrDot11BcastUpdatesSent |
|
|