
| SNMPv2-SMI | SNMPv2-CONF | SNMPv2-TC |
| CISCO-LWAPP-AP-MIB | CISCO-LWAPP-WLAN-MIB | CISCO-SMI |
| MODULE-IDENTITY | OBJECT-TYPE | Unsigned32 |
| Counter32 | Gauge32 | MODULE-COMPLIANCE |
| OBJECT-GROUP | TruthValue | cLApDot11IfEntry |
| cLWlanConfigEntry | ciscoMgmt |
| ciscoLwappQosMIB | 1.3.6.1.4.1.9.9.524 | ||
| This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. Information provided by this MIB is used to study the quality of service in the voice and video traffic on the WLAN. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Gratuitous Probe Response (GPR) The Gratuitous Probe Response feature aids in conserving battery power of WLAN-enabled cell phones by providing a high rate packet on the order of tens of milliseconds such that these kind of phones can wake up and wait at predefined intervals, to reduce battery power. The GPR packet is transmitted from the AP at a predefined time interval. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. TU A measurement of time in units of 1024 microseconds. User Priority ( UP ) Specifies a the priority rules in QOS for handling user priority. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol | |||
| MODULE-IDENTITY | |||
| ciscoLwappQosMIBNotifs | 1.3.6.1.4.1.9.9.524.0 | ||
| OBJECT IDENTIFIER | |||
| ciscoLwappQosMIBObjects | 1.3.6.1.4.1.9.9.524.1 | ||
| OBJECT IDENTIFIER | |||
| cLQd11aCACConfig | 1.3.6.1.4.1.9.9.524.1.1 | ||
| OBJECT IDENTIFIER | |||
| cLQd11aVoiceAdmCtrlSupport | 1.3.6.1.4.1.9.9.524.1.1.1 | ||
| This object is used to enable or disable admission control for voice traffic flowing through the 802.11a interfaces in the controller. When set to 'true', controller will reserve and manage max-bandwidth (cLQd11aVoiceMaxAdmBandwidth) and roaming-bandwidth (cLQd11aVoiceMaxRoamBandwidth) as per user configured values. When disabled, admission control will not be enforced. This may delay voice traffic depending on load on the WLAN. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11aVoiceMaxAdmBandwidth | 1.3.6.1.4.1.9.9.524.1.1.2 | ||
| This object denotes the maximum bandwidth that can be allocated by controller for voice traffic when admission control is enabled for for 802.11a interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11a network is not operational and the total value populated for this object for all the admission control attributes (voice, video) together does not exceed 100%. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11aVoiceMaxRoamBandwidth | 1.3.6.1.4.1.9.9.524.1.1.3 | ||
| This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11aVoiceMaxAdmBandwidth, that can be allocated to roaming clients for voice traffic, when admission control is enabled for 802.11a interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11a network is disabled and not operational. The value configured through this object takes effect when the 802.11a network is enabled. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11aVideoAdmCtrlSupport | 1.3.6.1.4.1.9.9.524.1.1.4 | ||
| This object is used to enable or disable admission control for video traffic flowing through the 802.11a interfaces in the controller. When set to 'true', controller will reserve and manage max-bandwidth (cLQd11aVideoMaxAdmBandwidth) and roaming-bandwidth (cLQd11aVideoMaxRoamBandwidth) as per user configured values. When disabled, admission control will not be enforced. This may delay video traffic depending on load on the WLAN. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11aVideoMaxAdmBandwidth | 1.3.6.1.4.1.9.9.524.1.1.5 | ||
| This object denotes the maximum bandwidth that can be allocated by controller for video traffic when admission control is enabled for 802.11a interfaces in the controller. When set to 0, all available bandwidth in 802.11a interfaces can be allocated to video traffic. Please note that the write operation on this object will be successful only if the 802.11a network is not operational and the total value populated for this object for all the admission control attributes (voice, video) together does not exceed 100%. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11aVideoMaxRoamBandwidth | 1.3.6.1.4.1.9.9.524.1.1.6 | ||
| This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11aVideoMaxAdmBandwidth, that can be allocated to roaming clients for video traffic, when admission control is enabled for 802.11a interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11a network is disabled and not operational. The value configured through this object takes effect when the 802.11a network is enabled and operational. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11aGprProbeInterval | 1.3.6.1.4.1.9.9.524.1.1.7 | ||
| This object is used to set GPR probe interval period to be used by all 802.11a interfaces in the controller, when the radios are advertising any WLAN with GPR support enabled. Please note that the write operation on this object will be successful only if the 802.11a network is not operational. The value configured through this object takes effect when the 802.11a network is enabled and operational. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 10..100 | ||
| cLQd11aVoiceCtrl | 1.3.6.1.4.1.9.9.524.1.1.8 | ||
| When admission control is enabled these parameters can be modified. loadBased - controller will reserve and manage max-bandwidth and roaming-bandwidth based on the load on the WLAN. static - controller will reserve and manage max-bandwidth (cLQd11aVoiceMaxAdmBandwidth) and roaming-bandwidth (cLQd11aVoiceMaxRoamBandwidth) as per user configured values. When ACM is disabled, admission control will not be enforced. This may delay voice traffic depending on the traffic on the WLAN. | |||
| OBJECT-TYPE | |||
| INTEGER | loadBased(1), static(2) | ||
| cLQd11aExpeditedBw | 1.3.6.1.4.1.9.9.524.1.1.9 | ||
| This object specifies if expedited BW feature is enabled or not. A value of 'true' will ensure that the APs advertise the expedited BW support in their beacons and association responses. A value of 'false' will ensure that the APs do not advertise the expedited BW support in their beacons and association responses. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11bCACConfig | 1.3.6.1.4.1.9.9.524.1.2 | ||
| OBJECT IDENTIFIER | |||
| cLQd11bVoiceAdmCtrlSupport | 1.3.6.1.4.1.9.9.524.1.2.1 | ||
| This object is used to enable or disable admission control for voice traffic flowing through the 802.11b/g interfaces in the controller. When set to 'true', controller will reserve and manage max-bandwidth (cLQd11bVoiceMaxAdmBandwidth) and roaming-bandwidth (cLQd11bVoiceMaxRoamingBandwidth) as per user configured values. When disabled, admission control will not be enforced. This may delay voice traffic depending on load on the WLAN. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11bVoiceMaxAdmBandwidth | 1.3.6.1.4.1.9.9.524.1.2.2 | ||
| This object denotes the maximum bandwidth that can be allocated by controller for voice traffic when admission control is enabled for 802.11b/g interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11b/g network is not operational and the total value populated for this object for all the admission control attributes (voice, video) together does not exceed 100%. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11bVoiceMaxRoamBandwidth | 1.3.6.1.4.1.9.9.524.1.2.3 | ||
| This object represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11bVoiceMaxAdmBandwidth, that can be allocated to roaming clients for voice traffic, when admission control is enabled for 802.11b interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11b/g network is not operational. The value configured through this object takes effect when the 802.11b/g network is enabled and operational. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11bVideoAdmCtrlSupport | 1.3.6.1.4.1.9.9.524.1.2.4 | ||
| This object is used to enable or disable admission control for video traffic flowing through the 802.11b/g interfaces in the controller. When set to 'true', controller will reserve and manage max-bandwidth (cLQd11bVideoMaxAdmBandwidth) and roaming-bandwidth (cLQd11bVideoMaxRoamBandwidth) as per user configured values. When disabled, admission control will not be enforced. This may delay video traffic depending on load on the WLAN. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11bVideoMaxAdmBandwidth | 1.3.6.1.4.1.9.9.524.1.2.5 | ||
| This object denotes the maximum bandwidth that can be allocated by controller for video traffic when admission control is enabled for 802.11b/g interfaces in the controller. When set to 0, all available bandwidth in 802.11b/g interfaces can be allocated to video traffic. Please note that the write operation on this object will be successful only if the 802.11b/g network is not operational and the total value populated for this object for all the admission control attributes (voice, video) together does not exceed 100%. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11bVideoMaxRoamBandwidth | 1.3.6.1.4.1.9.9.524.1.2.6 | ||
| This objects represents the bandwidth relative to the maximum allocated bandwidth indicated by cLQd11bVideoMaxAdmBandwidth, that can be allocated to roaming clients for video traffic, when admission control is enabled for 802.11b interfaces in the controller. Please note that the write operation on this object will be successful only if the 802.11b/g network is not operational. The value configured through this object takes effect when the 802.11b/g network is enabled and operational. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 0..100 | ||
| cLQd11bGprProbeInterval | 1.3.6.1.4.1.9.9.524.1.2.7 | ||
| This object is used to set GPR probe interval period to be used by all 802.11b/g interfaces in the controller, when the radios are advertising any WLAN with GPR support enabled. Please note that the write operation on this object will be successful only if the 802.11b/g network is not operational. The value configured through this object takes effect when the 802.11b/g network is enabled. | |||
| OBJECT-TYPE | |||
| Unsigned32 | 10..100 | ||
| cLQd11bVoiceCtrl | 1.3.6.1.4.1.9.9.524.1.2.8 | ||
| When admission control is enabled these parameters can be modified. loadBased - controller will reserve and manage max-bandwidth and roaming-bandwidth based on the load on the WLAN. static - controller will reserve and manage max-bandwidth (cLQd11bVoiceMaxAdmBandwidth) and roaming-bandwidth (cLQd11bVoiceMaxRoamBandwidth) as per user configured values. When ACM is disabled, admission control will not be enforced. This may delay voice traffic depending on the traffic on the WLAN. | |||
| OBJECT-TYPE | |||
| INTEGER | loadBased(1), static(2) | ||
| cLQd11bExpeditedBw | 1.3.6.1.4.1.9.9.524.1.2.9 | ||
| This object specifies if expedited BW feature is enabled or not. A value of 'true' will ensure that the APs advertise the expedited BW support in their beacons and association responses. A value of 'false' will ensure that the APs do not advertise the expedited BW support in their beacons and association responses. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11GprConfig | 1.3.6.1.4.1.9.9.524.1.3 | ||
| OBJECT IDENTIFIER | |||
| cLQd11GprTable | 1.3.6.1.4.1.9.9.524.1.3.1 | ||
| This table populates the GPR configuration on the WLANs configured on this controller. There exists a row in this table for each WLAN configured through cLWlanConfigTable. A row is added is to this table by the agent when a WLAN is created by the user through an explicit management action initiated from a network management station. Similarly a row gets deleted automatically when the user deletes the particular WLAN. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CLQd11GprEntry | |||
| cLQd11GprEntry | 1.3.6.1.4.1.9.9.524.1.3.1.1 | ||
| Each entry represents a conceptual row in cLQd11GprTable and corresponds to the GPR configuration on a WLAN. | |||
| OBJECT-TYPE | |||
| CLQd11GprEntry | |||
| cLQd11GprSupport | 1.3.6.1.4.1.9.9.524.1.3.1.1.1 | ||
| If 'true', then the corresponding radios that advertise this WLAN, will send Gratuitous Probe Response. If 'false', then the corresponding radios that advertise this WLAN, will not send Gratuitous Probe Response. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| cLQd11CACStats | 1.3.6.1.4.1.9.9.524.1.4 | ||
| OBJECT IDENTIFIER | |||
| cLQd11CACStatsTable | 1.3.6.1.4.1.9.9.524.1.4.1 | ||
| This table populates the call admission control metrics collected by observing the voice or video traffic on the dot11 interface of a particular AP. There exists a row in this table for each row corresponding to a dot11 interface found in cLApDot11IfTable. A row corresponding to a dot11 interface is added when an AP joins the controller. The row gets deleted when the AP dissociates from the controller. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| CLQd11CACStatsEntry | |||
| cLQd11CACStatsEntry | 1.3.6.1.4.1.9.9.524.1.4.1.1 | ||
| Each entry represents a conceptual row in CLQd11CACStatsTable and corresponds to the admission control statistics for a particular dot11 interface. | |||
| OBJECT-TYPE | |||
| CLQd11CACStatsEntry | |||
| cLQd11CacVoiceBwInUse | 1.3.6.1.4.1.9.9.524.1.4.1.1.1 | ||
| This object indicates the voice bandwidth in use as a percentage of the bandwidth configured through cLQd11aVoiceMaxAdmBandwidth or cLQd11bVoiceMaxAdmBandwidth, depending on the type of this dot11 interface. | |||
| OBJECT-TYPE | |||
| Gauge32 | 0..100 | ||
| cLQd11CacVideoBwInUse | 1.3.6.1.4.1.9.9.524.1.4.1.1.2 | ||
| This object indicates the video bandwidth in use as a percentage of the bandwidth configured through cLQd11aVideoMaxAdmBandwidth or cLQd11bVideoMaxAdmBandwidth, depending on the type of this dot11 interface. | |||
| OBJECT-TYPE | |||
| Gauge32 | 0..100 | ||
| cLQd11CacVoiceCallsInProgress | 1.3.6.1.4.1.9.9.524.1.4.1.1.3 | ||
| This object indicates the count of the number of voice calls currently in progress on this dot11 interface. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| cLQd11CacRoamVoiceCallsInProg | 1.3.6.1.4.1.9.9.524.1.4.1.1.4 | ||
| This object indicates the count of the number of voice calls initiated from roaming clients currently in progress on this dot11 interface. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| cLQd11CacTotalVoiceCallsAP | 1.3.6.1.4.1.9.9.524.1.4.1.1.5 | ||
| This object indicates the count of the number of voice calls observed on this dot11 interface ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacTotalRoamCallsAP | 1.3.6.1.4.1.9.9.524.1.4.1.1.6 | ||
| This object indicates the count of the number of voice and video calls initiated from roaming clients observed on this dot11 interface ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacVoiceCallsRejectedAP | 1.3.6.1.4.1.9.9.524.1.4.1.1.7 | ||
| This object indicates the count of the number of voice calls observed as rejected on this dot11 interface, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacRoamCallsRejectedAP | 1.3.6.1.4.1.9.9.524.1.4.1.1.8 | ||
| This object indicates the count of the number of voice and video calls initiated from roaming clients observed as rejected on this dot11 interface, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacRejCallsInsufBw | 1.3.6.1.4.1.9.9.524.1.4.1.1.9 | ||
| This object indicates the count of the number of calls observed as rejected on this dot11 interface due to insufficient bandwidth, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacRejCallsBadParams | 1.3.6.1.4.1.9.9.524.1.4.1.1.10 | ||
| This object indicates the count of the number of calls observed as rejected on this dot11 interface due to mismatch in call parameters, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacRejCallsPhyRate | 1.3.6.1.4.1.9.9.524.1.4.1.1.11 | ||
| This object indicates the count of the number of calls observed as rejected on this dot11 interface due to mismatch in 802.11 data rates, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQd11CacRejCallsQosPolicy | 1.3.6.1.4.1.9.9.524.1.4.1.1.12 | ||
| This object indicates the count of the number of calls observed as rejected on this dot11 interface due to restrictions imposed by QOS policies, ever since this AP has joined the controller. | |||
| OBJECT-TYPE | |||
| Counter32 | |||
| cLQEntConfConfig | 1.3.6.1.4.1.9.9.524.1.5 | ||
| OBJECT IDENTIFIER | |||
| ciscoLwappQosMIBConform | 1.3.6.1.4.1.9.9.524.2 | ||
| OBJECT IDENTIFIER | |||
| ciscoLwappQosMIBCompliances | 1.3.6.1.4.1.9.9.524.2.1 | ||
| OBJECT IDENTIFIER | |||
| ciscoLwappQosMIBCompliance | 1.3.6.1.4.1.9.9.524.2.1.1 | ||
| The compliance statement for the SNMP entities that implement the ciscoLwappQosMIB module. | |||
| MODULE-COMPLIANCE | |||
| ciscoLwappQosMIBComplianceRev1 | 1.3.6.1.4.1.9.9.524.2.1.2 | ||
| The compliance statement for the SNMP entities that implement the ciscoLwappQosMIB module. | |||
| MODULE-COMPLIANCE | |||
| ciscoLwappQosMIBGroups | 1.3.6.1.4.1.9.9.524.2.2 | ||
| OBJECT IDENTIFIER | |||
| ciscoLwappQosDot11aConfigGroup | 1.3.6.1.4.1.9.9.524.2.2.1 | ||
| This collection of objects represents the quality-of-service parameters 802.11a networks. | |||
| OBJECT-GROUP | |||
| ciscoLwappQosDot11bConfigGroup | 1.3.6.1.4.1.9.9.524.2.2.2 | ||
| This collection of objects represents the quality-of-service parameters 802.11b networks. | |||
| OBJECT-GROUP | |||
| ciscoLwappQosDot11WlanConfigGroup | 1.3.6.1.4.1.9.9.524.2.2.3 | ||
| This collection of objects represents the quality-of-services parameters on a particular WLAN. | |||
| OBJECT-GROUP | |||
| ciscoLwappQosDot11CacStatsGroup | 1.3.6.1.4.1.9.9.524.2.2.4 | ||
| This collection of objects provide the call admission control statistics observed on the dot11 interfaces of an AP. | |||
| OBJECT-GROUP | |||
| ciscoLwappQosDot11aConfigGroupSup1 | 1.3.6.1.4.1.9.9.524.2.2.5 | ||
| This collection of objects represents the quality-of-service parameters 802.11a networks. | |||
| OBJECT-GROUP | |||
| ciscoLwappQosDot11bConfigGroupSup1 | 1.3.6.1.4.1.9.9.524.2.2.6 | ||
| This collection of objects represents the quality-of-service parameters 802.11b networks. | |||
| OBJECT-GROUP | |||
| CLQd11GprEntry | |||
| SEQUENCE | |||
| TruthValue as cLQd11GprSupport | |||
| CLQd11CACStatsEntry | |||
| SEQUENCE | |||
| Gauge32 as cLQd11CacVoiceBwInUse | |||
| Gauge32 as cLQd11CacVideoBwInUse | |||
| Gauge32 as cLQd11CacVoiceCallsInProgress | |||
| Gauge32 as cLQd11CacRoamVoiceCallsInProg | |||
| Counter32 as cLQd11CacTotalVoiceCallsAP | |||
| Counter32 as cLQd11CacTotalRoamCallsAP | |||
| Counter32 as cLQd11CacVoiceCallsRejectedAP | |||
| Counter32 as cLQd11CacRoamCallsRejectedAP | |||
| Counter32 as cLQd11CacRejCallsInsufBw | |||
| Counter32 as cLQd11CacRejCallsBadParams | |||
| Counter32 as cLQd11CacRejCallsPhyRate | |||
| Counter32 as cLQd11CacRejCallsQosPolicy | |||