CISCO-LWAPP-REAP-MIB

File: CISCO-LWAPP-REAP-MIB.mib (23268 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB CISCO-LWAPP-WLAN-MIB CISCO-LWAPP-AP-MIB
CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
MODULE-COMPLIANCE OBJECT-GROUP TruthValue
StorageType RowStatus SnmpAdminString
cLWlanConfigEntry cLWlanIndex cLApSysMacAddress
ciscoMgmt

Defined Objects

ciscoLwappReapMIB 1.3.6.1.4.1.9.9.517
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. Information represented by this MIB is passed by the controller to those Cisco LWAPP APs, that can operate in stand-alone mode. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity is also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Native VLAN ID A switch port and/or AP can be configured with a 'native VLAN ID'. Untagged or priority-tagged frames are implicitly associated with the native VLAN ID. The default native VLAN ID is '1' if VLAN tagging is enabled. The native VLAN ID is '0' or 'no VLAN ID' if VLAN tagging is not enabled. Remote Edge Access Point ( REAP ) The LWAPP AP that can also act as a stand-alone AP when it loses communication with the controller it was associated with. When REAP can reach the controller (connected state), it gets help from controller to complete client authentication. When a controller is not reachable by REAP, it goes into standalone state and does client authentication by itself. All data packets from clients are either bridged locally (local-switch) or forwarded to the controller (central-switch) depending on the WLAN configuration. Virtual LAN VLAN defined in the IEEE 802.1Q VLAN standard supports logically segmenting of LAN infrastructure into different subnets or workgroups so that packets are switched only between ports within the same VLAN. VLAN ID Each VLAN is identified by a 12-bit 'VLAN ID'. A VLAN ID of '0' is used to indicate 'no VLAN ID'. Valid VLAN IDs range from '1' to '4095'. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol
MODULE-IDENTITY    

ciscoLwappReapMIBNotifs 1.3.6.1.4.1.9.9.517.0
OBJECT IDENTIFIER    

ciscoLwappReapMIBObjects 1.3.6.1.4.1.9.9.517.1
OBJECT IDENTIFIER    

ciscoLwappReapWlanConfig 1.3.6.1.4.1.9.9.517.1.1
OBJECT IDENTIFIER    

cLReapWlanConfigTable 1.3.6.1.4.1.9.9.517.1.1.1
This table represents the WLAN configuration sent by the controller to REAPs so that the APs can operate in stand-alone mode. LWAPP APs operating in REAP mode locally switch the data frames of the associated clients, rather than tunneling them through to the LWAPP controller as LWAPP data packets. The LWAPP controller passes this configuration set to the LWAPP AP during the AP initialization so that the AP can operate in stand-alone mode when it fails to reach the controller. The configuration is also passed to the REAP when they are individually modified through separate LWAPP messages. The REAP updates itself with the information received through these LWAPP messages. This table has a one-to-one relationship with cLWlanConfigTable of the CISCO-LWAPP-WLAN-MIB. There exist a row in this table corresponding to each row representing a WLAN in cLWlanConfigTable. Note that the configuration represented by this table is applicable only for REAPs. The controller will send this configuration set only to the REAP APs for their operation in standalone mode.
OBJECT-TYPE    
  SEQUENCE OF  
    CLReapWlanConfigEntry

cLReapWlanConfigEntry 1.3.6.1.4.1.9.9.517.1.1.1.1
Each entry represents a conceptual row in cLReapWlanConfigTable and corresponds to the packet switching configuration for a particular WLAN.
OBJECT-TYPE    
  CLReapWlanConfigEntry  

cLReapWlanEnLocalSwitching 1.3.6.1.4.1.9.9.517.1.1.1.1.1
This object indicates the behavior of the REAP when switching the data frames of the clients associated to it through the WLAN identified by cLWlanIndex. A value of 'true' indicates that the AP, on which this WLAN is configured, may locally switch the data packets of the clients in the WLAN instead of tunneling them to the central controller for switching. A value of 'false' indicates that the AP should tunnel all the data packets of the wireless clients in the WLAN to the central controller for switching. Note that the value of 'true' will be effective only if the WLAN is configured on a REAP.
OBJECT-TYPE    
  TruthValue  

ciscoLwappReapApConfig 1.3.6.1.4.1.9.9.517.1.2
OBJECT IDENTIFIER    

cLReapApConfigTable 1.3.6.1.4.1.9.9.517.1.2.1
This table represents the VLAN configuration of REAPs. The agent adds a row to this table corresponding to each row representing a REAP in cLApTable of the CISCO-LWAPP-AP-MIB. The agent deletes the row either when the AP dissociates from the controller or moved out of the remote mode.
OBJECT-TYPE    
  SEQUENCE OF  
    CLReapApConfigEntry

cLReapApConfigEntry 1.3.6.1.4.1.9.9.517.1.2.1.1
Each entry represents a conceptual row in cLReapApConfigTable and corresponds to the VLAN configuration of a REAP.
OBJECT-TYPE    
  CLReapApConfigEntry  

cLReapApNativeVlanId 1.3.6.1.4.1.9.9.517.1.2.1.1.1
This object defines the Native VLAN ID for the particular AP identified by cLApSysMacAddress. Note that this particular object can be modified through a Set request only if the AP is a REAP. The agent is expected to reject the attempt to set this object for APs in other modes.
OBJECT-TYPE    
  Unsigned32 1..4095  

cLReapApVlanEnable 1.3.6.1.4.1.9.9.517.1.2.1.1.2
This object indicates the availability of Native VLAN configured through cLReapApNativeVlanId on this REAP. A value of 'true' indicates that the VLAN configured as native through cLReapApNativeVlanId is enabled on the REAP and that the REAP can reach the controller through the native VLAN. A value of 'false' indicates that the VLAN configured as native through cLReapApNativeVlanId is disabled and the REAP can't reach the controller.
OBJECT-TYPE    
  TruthValue  

cLReapApVlanIdTable 1.3.6.1.4.1.9.9.517.1.2.2
This table defines the WLAN / VLAN Id mappings to be configured for the REAP identified by cLApSysMacAddress. VLAN Id configured through this table is passed to the respective REAP through the 'Add WLAN' LWAPP message, sent as part of the 'Configure Response message from the controller to the REAP, during the initialization of the REAP. The REAP maps the VLAN to the particular WLAN to locally switch the data packets when those APs are in standalone mode. Thus, the information added through this table is applicable for REAPs only. VLANs are configured on WLANs for which local switching of packets is enabled through cLReapWlanEnLocalSwitching. This means that a row is added to this table only if there are WLANs available on the controller with local switching enabled and the AP is a REAP.
OBJECT-TYPE    
  SEQUENCE OF  
    CLReapApVlanIdEntry

cLReapApVlanIdEntry 1.3.6.1.4.1.9.9.517.1.2.2.1
Each entry represents a conceptual row that corresponds to one WLAN / VLAN Id mapping to be applied to the REAP identified by cLApSysMacAddress.
OBJECT-TYPE    
  CLReapApVlanIdEntry  

cLReapApVlanId 1.3.6.1.4.1.9.9.517.1.2.2.1.1
This object represents the VLAN ID to be mapped to the WLAN identified by cLWlanIndex.
OBJECT-TYPE    
  Unsigned32 1..4095  

ciscoLwappReapGroupConfig 1.3.6.1.4.1.9.9.517.1.3
OBJECT IDENTIFIER    

cLReapGroupConfigTable 1.3.6.1.4.1.9.9.517.1.3.1
This table represents the configuration for REAPs so that the APs can be configured as a group. Entries are added or deleted by the user through the use of cLReapGroupRowStatus.
OBJECT-TYPE    
  SEQUENCE OF  
    CLReapGroupConfigEntry

cLReapGroupConfigEntry 1.3.6.1.4.1.9.9.517.1.3.1.1
Each entry represents a conceptual row in cLReapGroupConfigTable.
OBJECT-TYPE    
  CLReapGroupConfigEntry  

cLReapGroupName 1.3.6.1.4.1.9.9.517.1.3.1.1.1
This object uniquely identifies an entry in cLReapGroupConfigTable.
OBJECT-TYPE    
  SnmpAdminString  

cLReapGroupPrimaryRadiusIndex 1.3.6.1.4.1.9.9.517.1.3.1.1.2
The object represents the value that maps to the primary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configured for this group.
OBJECT-TYPE    
  Unsigned32  

cLReapGroupSecondaryRadiusIndex 1.3.6.1.4.1.9.9.517.1.3.1.1.3
The object represents the value that maps to the secondary RADIUS server for this group. A value of 0 indicates that the primary RADIUS server is not configured for this group.
OBJECT-TYPE    
  Unsigned32  

cLReapGroupStorageType 1.3.6.1.4.1.9.9.517.1.3.1.1.4
This object represents the storage type for this conceptual row.
OBJECT-TYPE    
  StorageType  

cLReapGroupRowStatus 1.3.6.1.4.1.9.9.517.1.3.1.1.5
This object represents the status column for a conceptual row in this table.
OBJECT-TYPE    
  RowStatus  

cLReapGroupApConfigTable 1.3.6.1.4.1.9.9.517.1.3.2
This table represents the group associated with an AP. Entries are added or deleted by the user through the use of cLReapGroupApRowStatus.
OBJECT-TYPE    
  SEQUENCE OF  
    CLReapGroupApConfigEntry

cLReapGroupApConfigEntry 1.3.6.1.4.1.9.9.517.1.3.2.1
Each entry represents a conceptual row in cLReapGroupApConfigTable.
OBJECT-TYPE    
  CLReapGroupApConfigEntry  

cLReapGroupApStorageType 1.3.6.1.4.1.9.9.517.1.3.2.1.1
This object represents the storage type for this conceptual row.
OBJECT-TYPE    
  StorageType  

cLReapGroupApRowStatus 1.3.6.1.4.1.9.9.517.1.3.2.1.2
This object represents the status column for a conceptual row in this table.
OBJECT-TYPE    
  RowStatus  

ciscoLwappReapMIBConform 1.3.6.1.4.1.9.9.517.2
OBJECT IDENTIFIER    

ciscoLwappReapMIBCompliances 1.3.6.1.4.1.9.9.517.2.1
OBJECT IDENTIFIER    

ciscoLwappReapMIBCompliance 1.3.6.1.4.1.9.9.517.2.1.1
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
MODULE-COMPLIANCE    

ciscoLwappReapMIBComplianceRev1 1.3.6.1.4.1.9.9.517.2.1.2
The compliance statement for the SNMP entities that implement the ciscoLwappReapMIB module.
MODULE-COMPLIANCE    

ciscoLwappReapMIBGroups 1.3.6.1.4.1.9.9.517.2.2
OBJECT IDENTIFIER    

ciscoLwappReapWlanConfigGroup 1.3.6.1.4.1.9.9.517.2.2.1
This collection of objects represent the WLAN configuration to be passed to the REAP.
OBJECT-GROUP    

ciscoLwappReapApConfigGroup 1.3.6.1.4.1.9.9.517.2.2.2
This collection of objects represent the information needed by the REAP AP to locally switch the client data packets. The collection also includes the VLAN configuration on the REAP.
OBJECT-GROUP    

ciscoLwappReapGroupConfigGroup 1.3.6.1.4.1.9.9.517.2.2.3
This collection of objects represent the information needed by the REAP APs to configure REAP groups.
OBJECT-GROUP    

Defined Objects

CLReapWlanConfigEntry  
SEQUENCE    
  TruthValue as cLReapWlanEnLocalSwitching  

CLReapApConfigEntry  
SEQUENCE    
  Unsigned32 as cLReapApNativeVlanId  
  TruthValue as cLReapApVlanEnable  

CLReapApVlanIdEntry  
SEQUENCE    
  Unsigned32 as cLReapApVlanId  

CLReapGroupConfigEntry  
SEQUENCE    
  SnmpAdminString as cLReapGroupName  
  Unsigned32 as cLReapGroupPrimaryRadiusIndex  
  Unsigned32 as cLReapGroupSecondaryRadiusIndex  
  StorageType as cLReapGroupStorageType  
  RowStatus as cLReapGroupRowStatus  

CLReapGroupApConfigEntry  
SEQUENCE    
  StorageType as cLReapGroupApStorageType  
  RowStatus as cLReapGroupApRowStatus