CISCO-SYSTEM-EXT-MIB

File: CISCO-SYSTEM-EXT-MIB.mib (39230 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB SNMPv2-MIB
CISCO-TC CISCO-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 Gauge32 MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP TEXTUAL-CONVENTION
TruthValue DateAndTime SnmpAdminString
InetAddressType InetAddress sysName
EntPhysicalIndexOrZero TimeIntervalSec ciscoMgmt

Defined Objects

ciscoSystemExtMIB 1.3.6.1.4.1.9.9.305
MIB module for monitoring High Availability, SNMP SET errors and bandwidths. This mib module also provides the information on core files that are generated in the system. GLOSSARY FIPS Federal Information Processing Standards Publication.
MODULE-IDENTITY    

ciscoSystemExtMIBNotifsPrefix 1.3.6.1.4.1.9.9.305.0
OBJECT IDENTIFIER    

ciscoSystemExtMIBObjects 1.3.6.1.4.1.9.9.305.1
OBJECT IDENTIFIER    

ciscoSysInfoGroup 1.3.6.1.4.1.9.9.305.1.1
OBJECT IDENTIFIER    

cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1
The average utilization of CPU on the active supervisor.
OBJECT-TYPE    
  Gauge32 0..100  

cseSysMemoryUtilization 1.3.6.1.4.1.9.9.305.1.1.2
The average utilization of memory on the active supervisor.
OBJECT-TYPE    
  Gauge32 0..100  

cseSysConfLastChange 1.3.6.1.4.1.9.9.305.1.1.3
The local date and time when the configuration was last changed. This object will be set to zero on power cycle or on reboot of the system. Also, if the clock is changed on local system it is set to zero.
OBJECT-TYPE    
  DateAndTime  

cseSysAutoSync 1.3.6.1.4.1.9.9.305.1.1.4
The state of the auto synchronization of images between the active and standby supervisor. Setting the value to sync when the existing value is sync, has no effect on the operation.
OBJECT-TYPE    
  INTEGER sync(1), noSync(2)  

cseSysAutoSyncState 1.3.6.1.4.1.9.9.305.1.1.5
The status of the current auto synchronization process, or if no such process is in progress, then the state of the most recent one. The value 'notStarted' indicates no auto synchronization process has occurred recently.
OBJECT-TYPE    
  INTEGER inProgress(1), succeeded(2), failed(3), notStarted(4)  

cseWriteErase 1.3.6.1.4.1.9.9.305.1.1.6
This object is used to initiate a write erase on the device's saved configuration file(s) from which the device loads its configuration when it restarts. If the value of this object is set to 'eraseAll', then all the saved configurations are removed. No action is taken when the this object is set to 'noOp'. When read, the value of this object is always 'noOp'.
OBJECT-TYPE    
  INTEGER noOp(1), eraseAll(2)  

cseSysConsolePortStatus 1.3.6.1.4.1.9.9.305.1.1.7
This object describes the status of the console port on this device. The status 'connected' means that there is a cable attached to the console port. The status 'notConnected' means that there is no connection out of the console port.
OBJECT-TYPE    
  INTEGER connected(1), notConnected(2)  

cseSysTelnetServiceActivation 1.3.6.1.4.1.9.9.305.1.1.8
Enables or disables the Telnet service on the device. In other words, it enables or disables the telneting to the device.
OBJECT-TYPE    
  TruthValue  

cseSysFIPSModeActivation 1.3.6.1.4.1.9.9.305.1.1.9
The object to enable/disable FIPS mode on the device. FIPS 140-2 is a set of security requirements for cryptographic modules and it details the U.S. Government requirements for cryptographic modules. A module will comprise both hardware and software, eg a datacenter switching or routing module. The module is said to be in FIPS enabled mode when a request is recieved to enable the FIPS mode and a set of self-tests are successfully run in response to the request. If the self-tests fail, then an appropriate error is returned.
OBJECT-TYPE    
  TruthValue  

cseSysUpTime 1.3.6.1.4.1.9.9.305.1.1.10
The time (in seconds) since the entire system was last re-initialized as a result of reload. The initialization being system loaded and running with a system image software on the first active supervisor (SUP). In High Availibility (HA) capable system / System that provides Supervisor module redundancy, this uptime indicates time elapsed since the first active SUP was booted. This will not change even if the active SUP goes down and stand-by takes over as active.
OBJECT-TYPE    
  TimeIntervalSec  

ciscoSysErrorGroup 1.3.6.1.4.1.9.9.305.1.2
OBJECT IDENTIFIER    

cseSnmpErrorTable 1.3.6.1.4.1.9.9.305.1.2.1
A table containing information about the errors which have recently caused the generation of a SNMP Response PDU with a non-zero value in its error-status field for SNMP Set Response PDU. This table serves as an extension to the SNMP's error status when a SNMP Set request fails. SNMP returns only a pre-defined set of standard error codes which does not convey the specific cause for an error. Typically, there is an incumbent and sizable burden on the configuration application to determine if the configuration request failure is the result of a resource issue, a security issue, or an application error (like an object depending on some other objects). So from a user perspective, it is important that a specific error be made known. Ideally, when a 'badValue' error occurs for a given set request, an application can query the command responder for more details on the error. This table provides a framework for the command responders to provide more information on the SET errors. It is up to the implementation to create entries in this table for either only certain SNMP errors or all of the SNMP errors. Note that only most recent incarnation of an entry is kept in this table.
OBJECT-TYPE    
  SEQUENCE OF  
    CseSnmpErrorEntry

cseSnmpErrorEntry 1.3.6.1.4.1.9.9.305.1.2.1.1
An entry (conceptual row) in the cseSnmpErrorTable, containing information about an error which has recently caused a SNMP SetRequest to fail. An entry is created by the agent on the occurrence of an error, and is deleted approximately 5 minutes later. The reasons for this are : - to prevent old entries clogging the table. - optimal utilization of the resources like memory.
OBJECT-TYPE    
  CseSnmpErrorEntry  

cseSnmpErrorAddressType 1.3.6.1.4.1.9.9.305.1.2.1.1.1
The type of address from which the error-ed SetRequest originated.
OBJECT-TYPE    
  InetAddressType  

cseSnmpErrorAddress 1.3.6.1.4.1.9.9.305.1.2.1.1.2
The address from which the error-ed SetRequest originated.
OBJECT-TYPE    
  InetAddress  

cseSnmpErrorRequestId 1.3.6.1.4.1.9.9.305.1.2.1.1.3
The request-id of the error-ed SetRequest.
OBJECT-TYPE    
  Unsigned32  

cseSnmpErrorCode 1.3.6.1.4.1.9.9.305.1.2.1.1.4
The code for the Mib object specific error which caused a SetRequest to fail. This error code is platform-specific and for debugging purposes only. For information on this code, the corresponding instance of cseSnmpErrorDescription must be used. This code is not the same as the value contained in the error-status field of SNMP Response PDU.
OBJECT-TYPE    
  Unsigned32  

cseSnmpErrorDescription 1.3.6.1.4.1.9.9.305.1.2.1.1.5
The error description for the error happened for the SetRequest.
OBJECT-TYPE    
  SnmpAdminString  

ciscoHaGroup 1.3.6.1.4.1.9.9.305.1.3
OBJECT IDENTIFIER    

cseHaRestartReason 1.3.6.1.4.1.9.9.305.1.3.2
The reason for most recent restart of a service on the 'active' supervisor.
OBJECT-TYPE    
  CseHaRestartReason  

cseHaRestartStateless 1.3.6.1.4.1.9.9.305.1.3.3
Tells if the most recent restart of a service on the 'active' supervisor was 'stateless' or not. A 'stateless' restart of a service is where no runtime information is preserved while restarting the service.
OBJECT-TYPE    
  TruthValue  

cseHaRestartService 1.3.6.1.4.1.9.9.305.1.3.4
Name of the service (or process) that was restarted on the 'active' supervisor.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..255)  

cseHaNotification 1.3.6.1.4.1.9.9.305.1.3.5
OBJECT IDENTIFIER    

cseHaNotificationPrefix 1.3.6.1.4.1.9.9.305.1.3.5.0
OBJECT IDENTIFIER    

cseHaRestartNotify 1.3.6.1.4.1.9.9.305.1.3.5.0.1
A service restart notification is generated whenever a service (or a process) on the 'active' supervisor is restarted.
NOTIFICATION-TYPE    
  cseHaRestartReason  
  cseHaRestartService  
  cseHaRestartStateless  

cseShutDownNotify 1.3.6.1.4.1.9.9.305.1.3.5.0.2
A system shutdown notification is generated whenever a system is going to shut down. The cseHaShutDownReason, describes the reason as to why the system is going to go down.
NOTIFICATION-TYPE    
  cseHaShutDownReason  

cseHaShutDownReason 1.3.6.1.4.1.9.9.305.1.3.6
The description of the reason as to why the system is going to go down.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..255)  

ciscoSwFailureGroup 1.3.6.1.4.1.9.9.305.1.4
OBJECT IDENTIFIER    

cseSwCorePath 1.3.6.1.4.1.9.9.305.1.4.1
Provides the path where the software cores are stored on the system. The management application can use this path to copy the cores from the system using CISCO-FLASH-MIB.
OBJECT-TYPE    
  SnmpAdminString SIZE(0..255)  

cseSwCoresTable 1.3.6.1.4.1.9.9.305.1.4.2
A table containing information about the system cores that have been generated as an effect of some system failures.
OBJECT-TYPE    
  SEQUENCE OF  
    CseSwCoresEntry

cseSwCoresEntry 1.3.6.1.4.1.9.9.305.1.4.2.1
An entry (conceptual row) in the cseSwCoresTable, containing information about cores that have been generated.
OBJECT-TYPE    
  CseSwCoresEntry  

cseSwCoresModule 1.3.6.1.4.1.9.9.305.1.4.2.1.1
The physical module on which the process crashed.
OBJECT-TYPE    
  EntPhysicalIndexOrZero  

cseSwCoresProcName 1.3.6.1.4.1.9.9.305.1.4.2.1.2
The name of the process that crashed and generated core.
OBJECT-TYPE    
  SnmpAdminString SIZE(1..64)  

cseSwCoresInstance 1.3.6.1.4.1.9.9.305.1.4.2.1.3
The instance of the core for a process identified by cseSwCoresProcName and on the module identified by cseSwCoresModule. To uniquely identify a core, the module number and process name are not sufficient as there could be multiple cores for the same module number and process name.
OBJECT-TYPE    
  Unsigned32  

cseSwCoresPID 1.3.6.1.4.1.9.9.305.1.4.2.1.4
The process identifier of the process that dumped the core.
OBJECT-TYPE    
  Unsigned32  

cseSwCoresTimeCreated 1.3.6.1.4.1.9.9.305.1.4.2.1.5
The time at which the core was created.
OBJECT-TYPE    
  DateAndTime  

cseSwCoresSlotNum 1.3.6.1.4.1.9.9.305.1.4.2.1.6
The slot number corresponding to the cseSwCoresModule in this chassis.
OBJECT-TYPE    
  Unsigned32  

cseSwCoresFileName 1.3.6.1.4.1.9.9.305.1.4.2.1.7
This object contains the core file-name(including the path, relative to the value in the cseSwCorePath object). If the cseSwCorePath contains zero length octet string, then this object will contain the filename with absolute path. If this object contains zero length octet string, then the core file is available in path identified in cseSwCorePath.
OBJECT-TYPE    
  SnmpAdminString  

cseFailNotification 1.3.6.1.4.1.9.9.305.1.4.3
OBJECT IDENTIFIER    

cseFailNotificationPrefix 1.3.6.1.4.1.9.9.305.1.4.3.0
OBJECT IDENTIFIER    

cseFailSwCoreNotify 1.3.6.1.4.1.9.9.305.1.4.3.0.1
A notification is generated whenever a software crash occurs and a core file is generated.
NOTIFICATION-TYPE    

cseFailSwCoreNotifyExtended 1.3.6.1.4.1.9.9.305.1.4.3.0.2
A notification is generated whenever a software crash occurs and a core file is generated.
NOTIFICATION-TYPE    
  sysName  
  cseSwCoresFileName  
  cseSwCorePath  
  cseSwCoresPID  

ciscoSwFailureNotifControl 1.3.6.1.4.1.9.9.305.1.5
OBJECT IDENTIFIER    

ciscoSwFailureNotifEnable 1.3.6.1.4.1.9.9.305.1.5.1
This object is used for administratively enabling/disabling the cseFailSwCoreNotify or cseFailSwCoreNotifyExtended notifications.
OBJECT-TYPE    
  TruthValue  

ciscoSystemExtMIBConformance 1.3.6.1.4.1.9.9.305.2
OBJECT IDENTIFIER    

ciscoSystemExtMIBCompliances 1.3.6.1.4.1.9.9.305.2.1
OBJECT IDENTIFIER    

ciscoSystemExtMIBCompliance 1.3.6.1.4.1.9.9.305.2.1.1
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev1 1.3.6.1.4.1.9.9.305.2.1.2
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev2 1.3.6.1.4.1.9.9.305.2.1.3
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev3 1.3.6.1.4.1.9.9.305.2.1.4
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev4 1.3.6.1.4.1.9.9.305.2.1.5
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev5 1.3.6.1.4.1.9.9.305.2.1.6
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev6 1.3.6.1.4.1.9.9.305.2.1.7
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev7 1.3.6.1.4.1.9.9.305.2.1.8
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBComplianceRev8 1.3.6.1.4.1.9.9.305.2.1.9
The compliance statement for entities which implement the CISCO-SYTEM-EXT-MIB.
MODULE-COMPLIANCE    

ciscoSystemExtMIBGroups 1.3.6.1.4.1.9.9.305.2.2
OBJECT IDENTIFIER    

ciscoSystemExtInfoGroup 1.3.6.1.4.1.9.9.305.2.2.1
A collection of objects for system information.
OBJECT-GROUP    

ciscoSystemExtErrorGroup 1.3.6.1.4.1.9.9.305.2.2.2
A collection of objects for logging SNMP set error.
OBJECT-GROUP    

ciscoSystemExtHaGroup 1.3.6.1.4.1.9.9.305.2.2.3
A collection of objects for High Availability.
OBJECT-GROUP    

ciscoSystemExtNotificationGroup 1.3.6.1.4.1.9.9.305.2.2.4
A collection of notifications for the High Availability.
NOTIFICATION-GROUP    

ciscoSystemExtInfoGroupRev1 1.3.6.1.4.1.9.9.305.2.2.5
A collection of objects for system information.
OBJECT-GROUP    

ciscoSystemExtInfoGroupOptional 1.3.6.1.4.1.9.9.305.2.2.6
A collection of objects for system information which are optional.
OBJECT-GROUP    

ciscoSystemExtSwFailureGroup 1.3.6.1.4.1.9.9.305.2.2.7
A collection of objects for system software failure information which are optional.
OBJECT-GROUP    

ciscoSystemExtInfoGroupRev2 1.3.6.1.4.1.9.9.305.2.2.8
A collection of objects for system information.
OBJECT-GROUP    

ciscoSystemExtSwFailureGroup2 1.3.6.1.4.1.9.9.305.2.2.9
A collection of objects for system software failure information which are optional.
OBJECT-GROUP    

ciscoSystemExtNotificationGroupSup1 1.3.6.1.4.1.9.9.305.2.2.10
A collection of notifications for the system MIB.
NOTIFICATION-GROUP    

ciscoSystemExtHaGroupRev1 1.3.6.1.4.1.9.9.305.2.2.11
A collection of objects for High Availability.
OBJECT-GROUP    

ciscoSystemExtInfoTelnetGroup 1.3.6.1.4.1.9.9.305.2.2.12
A collection of objects related to telnet support to the device.
OBJECT-GROUP    

ciscoSystemExtNotificationGroupSup2 1.3.6.1.4.1.9.9.305.2.2.13
A collection of notification related to core file creation.
NOTIFICATION-GROUP    

ciscoSystemExtSwFailureGroup3 1.3.6.1.4.1.9.9.305.2.2.14
A collection of objects related to the core file.
OBJECT-GROUP    

ciscoSystemExtSwFailureControlGroup 1.3.6.1.4.1.9.9.305.2.2.15
This group of objects controls the sending of notifications defined in this MIB module.
OBJECT-GROUP    

ciscoSystemExtInfoFIPSGroup 1.3.6.1.4.1.9.9.305.2.2.16
A collection of objects related to FIPS support to the device.
OBJECT-GROUP    

ciscoSystemExtInfoGroupRev3 1.3.6.1.4.1.9.9.305.2.2.17
A collection of objects for system information.
OBJECT-GROUP    

Defined Objects

CseHaRestartReason  
Reason codes for the restart of a service. unknown (1) - ungraceful exit ungracefulExit (2) - ungraceful exit otherSignal (3) - service got some other signal sigterm (4) - received SIGTERM softwareUpgrade (5) - software upgrade configUpdate (6) - config update configRemove (7) - config removal shutdown (8) - manually shutdown aborted (9) - aborted heartbeatFailure (10) - heartbeat failure userTerminate (11) - user termination gracefulExit (12) - graceful exit failureNoCallhome (13)- service exited but it does not want a callhome message to be generated serviceTimeout (14) - service timeout
TEXTUAL-CONVENTION    
  INTEGER unknown(1), ungracefulExit(2), otherSignal(3), sigterm(4), softwareUpgrade(5), configUpdate(6), configRemove(7), shutdown(8), aborted(9), heartbeatFailure(10), userTerminate(11), gracefulExit(12), noCallHomeFailure(13), serviceTimeout(14)  

CseSnmpErrorEntry  
SEQUENCE    
  InetAddressType as cseSnmpErrorAddressType  
  InetAddress as cseSnmpErrorAddress  
  Unsigned32 as cseSnmpErrorRequestId  
  Unsigned32 as cseSnmpErrorCode  
  SnmpAdminString as cseSnmpErrorDescription  

CseSwCoresEntry  
SEQUENCE    
  EntPhysicalIndexOrZero as cseSwCoresModule  
  SnmpAdminString as cseSwCoresProcName  
  Unsigned32 as cseSwCoresInstance  
  Unsigned32 as cseSwCoresPID  
  DateAndTime as cseSwCoresTimeCreated  
  Unsigned32 as cseSwCoresSlotNum  
  SnmpAdminString as cseSwCoresFileName