Nortel-MsCarrier-MscPassport-ImaMIB

File: Nortel-MsCarrier-MscPassport-ImaMIB.mib (185248 bytes)

Imported modules

RFC-1212 Nortel-MsCarrier-MscPassport-UsefulDefinitionsMIB Nortel-MsCarrier-MscPassport-StandardTextualConventionsMIB
Nortel-MsCarrier-MscPassport-TextualConventionsMIB Nortel-MsCarrier-MscPassport-LogicalProcessorMIB

Imported symbols

OBJECT-TYPE mscPassportMIBs Counter32
DisplayString StorageType RowStatus
Gauge32 Integer32 Unsigned32
AsciiString Hex NonReplicated
PassportCounter64 Link mscLpIndex
mscLpDS3Index mscLp mscLpDS3

Defined Objects

mscLpDS3Ima 1.3.6.1.4.1.562.36.2.1.12.5.7
OBJECT IDENTIFIER    

mscLpDS3ImaRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.5.7.1
This entry controls the addition and deletion of mscLpDS3Ima components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaRowStatusEntry

mscLpDS3ImaRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.1.1
A single entry in the table represents a single mscLpDS3Ima component.
OBJECT-TYPE    
  MscLpDS3ImaRowStatusEntry  

mscLpDS3ImaRowStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.1.1.1
This variable is used as the basis for SNMP naming of mscLpDS3Ima components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscLpDS3ImaComponentName 1.3.6.1.4.1.562.36.2.1.12.5.7.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpDS3ImaStorageType 1.3.6.1.4.1.562.36.2.1.12.5.7.1.1.4
This variable represents the storage type value for the mscLpDS3Ima tables.
OBJECT-TYPE    
  StorageType  

mscLpDS3ImaIndex 1.3.6.1.4.1.562.36.2.1.12.5.7.1.1.10
This variable represents the index for the mscLpDS3Ima tables.
OBJECT-TYPE    
  Integer32 0..13  

mscLpDS3ImaTest 1.3.6.1.4.1.562.36.2.1.12.5.7.2
OBJECT IDENTIFIER    

mscLpDS3ImaTestRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1
This entry controls the addition and deletion of mscLpDS3ImaTest components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaTestRowStatusEntry

mscLpDS3ImaTestRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1.1
A single entry in the table represents a single mscLpDS3ImaTest component.
OBJECT-TYPE    
  MscLpDS3ImaTestRowStatusEntry  

mscLpDS3ImaTestRowStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1.1.1
This variable is used as the basis for SNMP naming of mscLpDS3ImaTest components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscLpDS3ImaTestComponentName 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpDS3ImaTestStorageType 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1.1.4
This variable represents the storage type value for the mscLpDS3ImaTest tables.
OBJECT-TYPE    
  StorageType  

mscLpDS3ImaTestIndex 1.3.6.1.4.1.562.36.2.1.12.5.7.2.1.1.10
This variable represents the index for the mscLpDS3ImaTest tables.
OBJECT-TYPE    
  NonReplicated  

mscLpDS3ImaTestStateTable 1.3.6.1.4.1.562.36.2.1.12.5.7.2.10
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaTestStateEntry

mscLpDS3ImaTestStateEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.2.10.1
An entry in the mscLpDS3ImaTestStateTable.
OBJECT-TYPE    
  MscLpDS3ImaTestStateEntry  

mscLpDS3ImaTestAdminState 1.3.6.1.4.1.562.36.2.1.12.5.7.2.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpDS3ImaTestOperationalState 1.3.6.1.4.1.562.36.2.1.12.5.7.2.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpDS3ImaTestUsageState 1.3.6.1.4.1.562.36.2.1.12.5.7.2.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpDS3ImaTestSetupTable 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11
This group contains all of the operational data for a Test component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaTestSetupEntry

mscLpDS3ImaTestSetupEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1
An entry in the mscLpDS3ImaTestSetupTable.
OBJECT-TYPE    
  MscLpDS3ImaTestSetupEntry  

mscLpDS3ImaTestPurpose 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.1
This attribute records the purpose of the test so that the test results can be associated and properly analyzed.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscLpDS3ImaTestType 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.2
This attribute is the type of test to be run. The available test types include the following: card test sets up an internal loop on the board and runs a bit error rate test. manual test assumes the line is looped back externally and a bit error rate test is performed. localLoop test loops back the local modem and performs a bit error rate test. remoteLoop test loops back the remote modem (or CSU) and performs a bit error rate test. externalLoop test loops back the line to the far end. payloadLoop test only loops back the payload data received from the incoming line. remoteLoopThisTrib loops this particular tributary back at the far end, using services provided by the parent. v54RemoteLoop initiates a V.54 Remote Loopback test. pn127RemoteLoop initiates a PN127 Remote Loopback test. Note that not all test types are not supported by all function processors.
OBJECT-TYPE    
  INTEGER card(0), manual(1), localLoop(2), remoteLoop(3), externalLoop(4), payloadLoop(5), remoteLoopThisTrib(6), v54RemoteLoop(7), pn127RemoteLoop(8)  

mscLpDS3ImaTestFrmSize 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.3
This attribute defines the size of the test data frames in number of bytes.
OBJECT-TYPE    
  Unsigned32 4..4096  

mscLpDS3ImaTestFrmPatternType 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.4
This attribute defines the type of data pattern generation to use. The following lists the available pattern types: ccitt32kBitPattern is a pseudo-random sequence of 32 kbit. ccitt8MBitPattern is a pseudo-random sequence of 8Mbit. customizedPattern is the pattern defined in the customizedPattern attribute.
OBJECT-TYPE    
  INTEGER ccitt32kBitPattern(0), ccitt8MBitPattern(1), customizedPattern(2)  

mscLpDS3ImaTestCustomizedPattern 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.5
This attribute allows a customized 32 bit pattern to be defined for use in the test data frames. This attribute is used when the attribute frmPatternType is set to CustomizedPattern. Note that a 55 hex pattern is an alternating 1 and 0 pattern.
OBJECT-TYPE    
  Hex 0..4294967295  

mscLpDS3ImaTestDataStartDelay 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.6
This attribute specifies the time delay (in seconds) between when the test expects the loop to have been set up, to when the test data actually starts to be transmitted. This attribute is to accommodate some non-standard equipment that requires extra time for setting up a requested loop. This attribute is ignored when the test type is set to externalLoop.
OBJECT-TYPE    
  Unsigned32 0..1814400  

mscLpDS3ImaTestDisplayInterval 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.7
This attribute defines the interval (in minutes) between which interim test results are to be displayed. Results are displayed at the operator console at which the test was started. When the test type is set to externalLoop, this attribute is ignored. There will be no display of results if displayInterval is set to 0. This attribute can be changed anytime.
OBJECT-TYPE    
  Unsigned32 0..30240  

mscLpDS3ImaTestDuration 1.3.6.1.4.1.562.36.2.1.12.5.7.2.11.1.8
This attribute is the duration (in minutes) that test data will be transmitted. In the case of an externalLoop, this is the time that the loop is in effect. Note that dataStartDelay does not apply to the externalLoop.
OBJECT-TYPE    
  Unsigned32 1..30240  

mscLpDS3ImaTestResultsTable 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12
This group contains all the statistics related attributes of the Test component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaTestResultsEntry

mscLpDS3ImaTestResultsEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1
An entry in the mscLpDS3ImaTestResultsTable.
OBJECT-TYPE    
  MscLpDS3ImaTestResultsEntry  

mscLpDS3ImaTestElapsedTime 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.1
This attribute is the number of minutes elapsed since the test started for an externalLoop test. For a data test, this is the time since test data was first transmitted.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaTestTimeRemaining 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.2
This attribute is the number of minutes remaining before the test is to be stopped according to the duration attribute.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaTestCauseOfTermination 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.3
This attribute indicates either the status of the test or the cause of the test's termination: neverStarted indicates that the test has not yet been started. testRunning indicates that the test has been started. stoppedByOperator indicates that the operator issued a stop command on a test that was running. testTimeExpired indicates that the test ran for the time specified by the test's duration. loopCodeSyncFailed indicates that the local end failed to synchronize to the loopCode pattern. The local end transmits the loopCode pattern to cause the remote end to apply a loopback, after which the local end should receive the loopCode pattern. The exact pattern used to request loopCode depends on the test type. This failure indicates a high rate of transmission errors, or that the remote end has failed to apply the loopback. patternSyncFailed indicates that the local end failed to synchronize to the frmPatternType test pattern, that should have been looped back at the remote end. This failure indicates a high rate of transmission errors or the absence of a loopback. patternSyncLost indicates that the local end gained and then lost synchronization to the returned frmPatternType test pattern. This failure indicates a sudden increase in transmission errors, frame slippage, or the removal of an existing loopback. unknown is set when a reason to terminate other than those listed here is encountered. Note: Only MSA cards support recognition of the failures loopCodeSyncFailed, patternSyncFailed and patternSyncLost. Other cards will not terminate the test under the conditions described by these values.
OBJECT-TYPE    
  INTEGER testTimeExpired(0), stoppedByOperator(1), unknown(2), neverStarted(3), testRunning(4), hardwareReconfigured(5), loopCodeSyncFailed(6), patternSyncFailed(7), patternSyncLost(8)  

mscLpDS3ImaTestBitsTx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.4
This attribute is the total number of bits sent during the test period. As long as the line speed of the hardware interface is less than 70 Mbit/s, this counter is not expected to reach the maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestBytesTx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.5
This attribute is the total number of bytes sent during the test period. This counter is not expected to reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestFrmTx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.6
This attribute is the total number of frames sent during the test period. This counter is not expected to reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestBitsRx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.7
This attribute is the total number of bits received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach the maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestBytesRx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.8
This attribute is the total number of bytes received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestFrmRx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.9
This attribute is the total number of frames received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestErroredFrmRx 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.10
This attribute is not displayed for ATM cards because the physical layer drops all errored frames at the controller interface. For all other card types, this attribute is the total number of errored frames received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpDS3ImaTestBitErrorRate 1.3.6.1.4.1.562.36.2.1.12.5.7.2.12.1.11
This attribute is not displayed for ATM cards because the physical layer drops all errored frames at the controller interface. For all other card types, this attribute is the calculated bit error rate on the link. Test data are generated and sent in frames of a preset size (frameSize). The Test component will try to estimate the number of bit errors in any errored frame which is identifiable. The statistics will be updated accordingly. A lost frame (may be due to an error on the flag sequence) will be discarded for the bit error rate calculation. The result is presented in the form of xEsyy, where x is the mantissa, syy is the exponent, for example 0E+00, 2E-09. Note that the bitErrorRate is an estimate only. For more reliable test results, the test should be done over a long period. Multiple tests would also improve the confidence level of the test results.
OBJECT-TYPE    
  AsciiString SIZE(5)  

mscLpDS3ImaLk 1.3.6.1.4.1.562.36.2.1.12.5.7.3
OBJECT IDENTIFIER    

mscLpDS3ImaLkRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1
This entry controls the addition and deletion of mscLpDS3ImaLk components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaLkRowStatusEntry

mscLpDS3ImaLkRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1.1
A single entry in the table represents a single mscLpDS3ImaLk component.
OBJECT-TYPE    
  MscLpDS3ImaLkRowStatusEntry  

mscLpDS3ImaLkRowStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1.1.1
This variable is used as the basis for SNMP naming of mscLpDS3ImaLk components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscLpDS3ImaLkComponentName 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpDS3ImaLkStorageType 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1.1.4
This variable represents the storage type value for the mscLpDS3ImaLk tables.
OBJECT-TYPE    
  StorageType  

mscLpDS3ImaLkIndex 1.3.6.1.4.1.562.36.2.1.12.5.7.3.1.1.10
This variable represents the index for the mscLpDS3ImaLk tables.
OBJECT-TYPE    
  Integer32 0..31  

mscLpDS3ImaLkProvTable 1.3.6.1.4.1.562.36.2.1.12.5.7.3.10
This group contains the provisionable attributes for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaLkProvEntry

mscLpDS3ImaLkProvEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.3.10.1
An entry in the mscLpDS3ImaLkProvTable.
OBJECT-TYPE    
  MscLpDS3ImaLkProvEntry  

mscLpDS3ImaLkInterfaceName 1.3.6.1.4.1.562.36.2.1.12.5.7.3.10.1.1
This attribute associates the Link subcomponent with a specific interface on a function processor, for example Lp/5 E1/3 Chan/0. If IMA groups and independent links coexist on a card running IMA and per-VC queueing is enabled, plan the selection of DS1 or E1 ports to be used by the IMA group carefully. For a 4pDS3ChAtm function processor there is no per-VC queueing.
OBJECT-TYPE    
  Link  

mscLpDS3ImaLkOperTable 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11
This group contains the operational attributes for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaLkOperEntry

mscLpDS3ImaLkOperEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1
An entry in the mscLpDS3ImaLkOperTable.
OBJECT-TYPE    
  MscLpDS3ImaLkOperEntry  

mscLpDS3ImaLkFailureCause 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.1
This attribute indicates the failure cause on this link. Possible values are: noFailure: there is no failure on this link. interfaceDown: the physical port used by the link is down. lif: the link is in loss of IMA frame (LIF) state. lods: the link is in loss of delay synchronization (LODS) state; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group. It must be noted that hysteresis is used for the LODS condition. protocolError: the link is down because of a time-out or because bad values are being received in IMA Control Protocol (ICP) cells. remoteFailure: the far end link is down. misconnected: the link is down because the IMA group has declared, after using its transmit test pattern procedure, that this link is not properly connected. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedFrameLength: the link is down because it is receiving from the far end a frame length which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedSymmetry: the link is down because it is receiving from the far end a group symmetry which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. noIcp: the link is down because it is not receiving IMA Control Protocol (ICP) cells. This value can occur only if the protocol for the IMA group is atmForum10.
OBJECT-TYPE    
  INTEGER noFailure(0), interfaceDown(1), lif(2), lods(3), protocolError(4), remoteFailure(5), misconnected(6), unsupportedFrameLength(7), unsupportedSymmetry(8), noIcp(9)  

mscLpDS3ImaLkRemoteDefect 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.2
This attribute indicates the IMA remote defect indicator (RDI) currently being received on this link. Possible values are: noDefect: no defect. physicalLayerDefect: the interface used by the remote link has a physical layer defect. This value can occur only if the protocol for the IMA group is atmForum10. interfaceDown: the physical interface used by the remote link is down.This value can occur only if the protocol for the IMA group is proprietary. lif: the remote link has a loss of IMA frame (LIF) defect. lods: the remote link has a loss of delay synchronization (LODS) defect; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group.
OBJECT-TYPE    
  INTEGER noDefect(0), physicalLayerDefect(1), lif(2), lods(3), interfaceDown(4)  

mscLpDS3ImaLkRemoteLid 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.3
This attribute indicates the link identifier (LID) used by the remote IMA group on the physical link. A value of 0 will be displayed if the link is not receiving IMA Control Protocol (ICP) cells or if the physical layer is down.
OBJECT-TYPE    
  Unsigned32 0..31  

mscLpDS3ImaLkRelativeDelay 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.4
This attribute indicates the latest measured differential delay (rounded up in milliseconds) between this link and the link, in the same IMA group, having the least delay. A value of 4294967295 indicates that the relative delay could not be measured. This can be due to physical layer problems or to no IMA Control Protocol (ICP) cells being received on the link.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaLkLastOifCause 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.5
This attribute indicates the cause of the last out of IMA frame (OIF) anomaly on the link. It will always have a value of noOif if the protocol for the IMA group is proprietary. Possible values are: noOif: no OIF was detected. badFrameLength: an IMA Control Protocol (ICP) cell with an unexpected frame length was received. badGid: an ICP cell with an unexpected group identifier (GID) was received. badLid: an ICP cell with an unexpected link identifier (LID) was received. badOffset: an ICP cell with an unexpected cell offset was received. badSequenceNumber: an ICP cell with an unexpected frame sequence number was received. stuffError: an illegal stuffing sequence was received. missingIcp: an expected ICP cell was not received. unexpectedIcp: an unexpected ICP cell was received. erroredIcp: two consecutive errored ICP cells were received. noCells: no cells are being received on the link. idleCell: an idle cell was received on the link.
OBJECT-TYPE    
  INTEGER noOif(0), badFrameLength(1), badGid(2), badLid(3), badOffset(4), badSequenceNumber(5), stuffError(6), missingIcp(7), unexpectedIcp(8), erroredIcp(9), noCells(10), idleCell(11)  

mscLpDS3ImaLkStatsTable 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12
This group contains the statistics data for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaLkStatsEntry

mscLpDS3ImaLkStatsEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1
An entry in the mscLpDS3ImaLkStatsTable.
OBJECT-TYPE    
  MscLpDS3ImaLkStatsEntry  

mscLpDS3ImaLkRunningTime 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.1
This attribute counts the length of time (in seconds) for which the Link component has been running.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaLkUnavailSecs 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.2
For an IMA group whose protocol is atmForum10, this attribute counts the number of unavailable seconds. Unavailability begins at the start of 10 contiguous severely errored seconds (SES) and ends at the start of 10 contiguous seconds with no SES. For an IMA group whose protocol is proprietary, this attribute counts the number of one second intervals during which the Link component has been out of service.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaLkFailures 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.3
This attribute counts the number of failures, during link addition or normal operation, that the link has experienced.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaLkUnusableSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.4
This attribute counts the number of one second intervals during which the near end has been in an unusable state. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkSevErroredSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.5
This attribute counts the number of one second intervals in which at least 30 percent of the IMA Control Protocol (ICP) cells were counted as ICP violations or at least one link defect (physical layer, LIF and LODS defects) was detected. This attribute will not increment during UAS (Unavailable Second) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkFarEndUnusableSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.6
This attribute counts the number of one second intervals during which the 'Tx/Rx Unusable' condition has been received from the far end. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkFarEndSevErroredSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.7
This attribute counts the number of one second intervals containing one or more RDI defects. This attribute will not increment during FEUAS (Far-End Unavailable Second) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkFarEndUnavailSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.8
This attribute counts the number of unavailable seconds at the far end. Unavailability begins at the start of 10 contiguous severely errored seconds (SES) at the far end and ends at the start of 10 contiguous seconds at the far end with no SES. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkIcpViolations 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.9
This attribute counts the number of errored, invalid or missing IMA Control Protocol (ICP) cells during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkTxStuffEvents 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.10
This attribute counts the number of Stuff events transmitted during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkRxStuffEvents 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.11
This attribute counts the number of Stuff events received during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkIdleCellSec 1.3.6.1.4.1.562.36.2.1.12.5.7.3.12.1.12
This attributes counts the number of one second intervals during which one or more idle cells was received. The reception of idle cells is an abnormal condition which could be caused by the remote IMA using the Common Transmit Clock mode with ports whose clock sources are not synchronized. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpDS3ImaLkStateTable 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaLkStateEntry

mscLpDS3ImaLkStateEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1
An entry in the mscLpDS3ImaLkStateTable.
OBJECT-TYPE    
  MscLpDS3ImaLkStateEntry  

mscLpDS3ImaLkAdminState 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpDS3ImaLkOperationalState 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpDS3ImaLkUsageState 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpDS3ImaLkAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscLpDS3ImaLkProceduralStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaLkControlStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaLkAlarmStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaLkStandbyStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscLpDS3ImaLkUnknownStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.3.13.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscLpDS3ImaProvTable 1.3.6.1.4.1.562.36.2.1.12.5.7.10
This group contains the provisionable attributes for the Ima component. The default values of linkSelectionCriterion and linkRetryTimeout depend on card type.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaProvEntry

mscLpDS3ImaProvEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1
An entry in the mscLpDS3ImaProvTable.
OBJECT-TYPE    
  MscLpDS3ImaProvEntry  

mscLpDS3ImaLinkSelectionCriterion 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.1
This attribute specifies the method to be used by the IMA group when selecting links to be activated. This comes into effect only when the configured links do not respect the maximum differential delay (otherwise all links are accepted). If leastDelay is chosen, first the link having the smallest delay is selected as the reference link. The IMA group includes all links which respect the maximum differential delay relative to the reference link. If maxBandwidth is chosen, the IMA group selects the maximum possible number of links, with each selected link respecting the maximum differential delay relative to every other selected link. When more than one possibility exists, the combination which offers the least delay isselected. The default value for Multi-Service Access cards is leastDelay, and for all other cards is maxBandwidth. On Multi-Service Access cards leastDelay is the only acceptable provisionable value.
OBJECT-TYPE    
  INTEGER leastDelay(0), maxBandwidth(1)  

mscLpDS3ImaMaxDiffDelay 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.2
This attribute specifies the maximum differential delay between links acceptable in the IMA group. If a link violates that maximum differential delay, it will not be active in the IMA group and an alarm will be generated.
OBJECT-TYPE    
  Unsigned32 1..100  

mscLpDS3ImaLinkRetryTimeout 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.3
This attribute specifies the amount of time before reactivation of a link is attempted after it recovers from a failure condition. The default value for Multi-Service Access cards is 1, and for all other cards is 10. On Multi-Service Access cards 1 is the only acceptable provisionable value.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscLpDS3ImaApplicationFramerName 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.4
This attribute defines the link to the AtmIf component using the Ima. An example is AtmIf/31.
OBJECT-TYPE    
  Link  

mscLpDS3ImaTransmitClockMode 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.5
This attribute specifies the transmit clocking mode. If itc (Independent Transmit Clock) is chosen, the physical ports used by the IMA group may have different clocking sources. If ctc (Common Transmit Clock) is chosen, it is recommended that the physical ports used by the IMA group have the same clocking source. However, if the physical ports have different clocking sources, the operator should ensure that all the clocking sources have the same rate.
OBJECT-TYPE    
  INTEGER itc(0), ctc(1)  

mscLpDS3ImaProtocol 1.3.6.1.4.1.562.36.2.1.12.5.7.10.1.6
This attribute specifies what protocol the component should run. If atmForum10 is chosen, the ATM Forum's IMA protocol (version 1.0) will be used and signalled in outgoing IMA Control Protocol (ICP) cells. This protocol is specified in version 1.1 of the ATM Forum IMA specification. The IMA group will come up only if the far end IMA also uses the ATM Forum's IMA protocol. If proprietary is chosen, Nortel's proprietary IMA protocol will be used. The IMA group will come up only if the far end IMA also uses Nortel's proprietary IMA protocol. This IMA group will not inter-operate with IMA implementations from other vendors. Feature ima must be provisioned on the LP for this protocol to be used.
OBJECT-TYPE    
  INTEGER atmForum10(0), proprietary(1)  

mscLpDS3ImaOperTable 1.3.6.1.4.1.562.36.2.1.12.5.7.11
This group contains the operational attributes for the Ima component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaOperEntry

mscLpDS3ImaOperEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1
An entry in the mscLpDS3ImaOperTable.
OBJECT-TYPE    
  MscLpDS3ImaOperEntry  

mscLpDS3ImaFailureCause 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.1
This attribute indicates the cause of the current local end failure experienced by the IMA group. The failure may have occurred during a start-up procedure or during normal operation. Possible values are: noFailure: no local end failure. noGoodLinksInStartup: no good links were available during IMA start-up. badGidInStartup: during start-up, different group identifiers (GIDs) were received on the links. badLidInStartup: during start-up, duplicate link identifiers (LIDs) were received on the links. unsupportedFrameLengthInStartup: during start-up, an unsupported frame length was received. timeoutInStartup: a time-out has occurred during start-up. noGoodLinks: no good links are available in the IMA group. remoteFailure: the far end is down. unsupportedSymmetryInStartup: the symmetry proposed by the far end is not supported on the near-end. This value will occur when the IMA group is running the ATM Forum protocol and the far end is proposing a group symmetry other than 'symmetric configuration and operation'.
OBJECT-TYPE    
  INTEGER noFailure(0), noGoodLinksInStartup(1), badGidInStartup(2), badLidInStartup(3), unsupportedFrameLengthInStartup(4), timeoutInStartup(5), noGoodLinks(6), remoteFailure(7), unsupportedSymmetryInStartup(8)  

mscLpDS3ImaRemoteDefect 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.2
This attribute indicates the cause of the current far end defect experienced by the IMA group. For the ATM Forum IMA protocol, possible values are: noDefect: no defect. unsupportedFrameLengthInStartup: during the far end's start-up, an unsupported frame length was received. unsupportedSymmetryInStartup: during the far end's start-up, an unsupported symmetry configuration was received. otherAbortStartup: the far end has aborted its start-up for another reason. This could be because different Gids were received on the links or if duplicate link identifiers (LIDs) were received. insufficientLinks: the far end does not have sufficient links active. This value will be displayed if the far end IMA group is locked. blocked: the far end IMA group is blocked. For the proprietary IMA protocol, possible values are: noDefect: no defect. noGoodLinksInStartup: no good links were available during the far end's start-up. badGidInStartup: during the far end's start-up, different GIDs were received on the links. badLidInStartup: during the far end's start-up, duplicate link identifiers (LIDs) were received on the links. unsupportedFrameLengthInStartup: during the far end's start-up, an unsupported frame length was received. timeoutInStartup: a time out has occurred during the far end's start- up. noGoodLinks: no good links are available in the far end IMA group. locked: the far end IMA group is locked.
OBJECT-TYPE    
  INTEGER noDefect(0), noGoodLinksInStartup(1), badGidInStartup(2), badLidInStartup(3), unsupportedFrameLengthInStartup(4), timeoutInStartup(5), noGoodLinks(6), locked(7), unsupportedSymmetryInStartup(8), otherAbortStartup(9), insufficientLinks(10), blocked(11)  

mscLpDS3ImaRemoteLidsConfig 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.3
This attribute indicates all the links which have been configured in the remote IMA group. For example, if links 1, 3 and 5 have been configured in the remote IMA group, this attribute would contain 1 3 5. Description of bits: n0(0) n1(1) n2(2) n3(3) n4(4) n5(5) n6(6) n7(7) n8(8) n9(9) n10(10) n11(11) n12(12) n13(13) n14(14) n15(15) n16(16) n17(17) n18(18) n19(19) n20(20) n21(21) n22(22) n23(23) n24(24) n25(25) n26(26) n27(27) n28(28) n29(29) n30(30) n31(31)
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

mscLpDS3ImaRemoteLidsActive 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.4
This attribute indicates all the links which are active in the remote IMA group. For example, if links 1 and 5 are active in the remote IMA, this attribute would contain 1 5. Description of bits: n0(0) n1(1) n2(2) n3(3) n4(4) n5(5) n6(6) n7(7) n8(8) n9(9) n10(10) n11(11) n12(12) n13(13) n14(14) n15(15) n16(16) n17(17) n18(18) n19(19) n20(20) n21(21) n22(22) n23(23) n24(24) n25(25) n26(26) n27(27) n28(28) n29(29) n30(30) n31(31)
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

mscLpDS3ImaCellCapacity 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.5
This attribute indicates the total cell capacity (in cells per second) which is provided to the ATM layer. This cell capacity takes into account the physical and IMA level overheads.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaRemoteGid 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.6
This attribute indicates the IMA group identifier (GID) used by the remote IMA. A value of 0 will be displayed if the group is not receiving IMA Control Protocol (ICP) cells. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Unsigned32 0..255  

mscLpDS3ImaClockingModeMismatch 1.3.6.1.4.1.562.36.2.1.12.5.7.11.1.7
This attribute indicates whether or not both ends of the IMA group are using the same transmit clocking mode (itc/ctc). Its value will be yes if both ends are not using the same transmit clocking mode. A clocking mode mismatch does not prevent an IMA group from coming up and can be corrected by using the same clocking mode at both ends. This attribute will always have a value of no if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscLpDS3ImaStatsTable 1.3.6.1.4.1.562.36.2.1.12.5.7.12
This group contains the statistics data for the Ima component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaStatsEntry

mscLpDS3ImaStatsEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1
An entry in the mscLpDS3ImaStatsTable.
OBJECT-TYPE    
  MscLpDS3ImaStatsEntry  

mscLpDS3ImaRunningTime 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1.1
This attribute indicates the length of time (in seconds) for which the Ima component has been in the unlocked state or has been used for operational testing.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaUnavailSecs 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1.2
This attribute indicates the number of one second intervals during which the Ima component has been unlocked and out of service.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaFailures 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1.3
This attribute indicates the number of complete failures, during start-up or normal operation, that the Ima component has experienced since being added. It must be noted that a service degradation, such as 1 of the 3 links in an IMA group being down, is not counted as a failure. If an Ima component is in a failure loop and does not come up, this count will only increase by 1.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpDS3ImaReceiveCellUtilization 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1.4
This attribute indicates the ratio of the number of valid, assigned user cells received on the IMA group to the IMA cell capacity (based on the number of active links). The utilization is calculated over a one minute period. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Gauge32 0..100  

mscLpDS3ImaTransmitCellUtilization 1.3.6.1.4.1.562.36.2.1.12.5.7.12.1.5
This attribute indicates the ratio of the number of user cells transmitted on the IMA group to the IMA cell capacity (based on the number of active links). The utilization is calculated over a one minute period. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Gauge32 0..100  

mscLpDS3ImaCidDataTable 1.3.6.1.4.1.562.36.2.1.12.5.7.13
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaCidDataEntry

mscLpDS3ImaCidDataEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.13.1
An entry in the mscLpDS3ImaCidDataTable.
OBJECT-TYPE    
  MscLpDS3ImaCidDataEntry  

mscLpDS3ImaCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.12.5.7.13.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscLpDS3ImaStateTable 1.3.6.1.4.1.562.36.2.1.12.5.7.14
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpDS3ImaStateEntry

mscLpDS3ImaStateEntry 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1
An entry in the mscLpDS3ImaStateTable.
OBJECT-TYPE    
  MscLpDS3ImaStateEntry  

mscLpDS3ImaAdminState 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpDS3ImaOperationalState 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpDS3ImaUsageState 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpDS3ImaAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscLpDS3ImaProceduralStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaControlStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaAlarmStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpDS3ImaStandbyStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscLpDS3ImaUnknownStatus 1.3.6.1.4.1.562.36.2.1.12.5.7.14.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscLpIma 1.3.6.1.4.1.562.36.2.1.12.22
OBJECT IDENTIFIER    

mscLpImaRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.22.1
This entry controls the addition and deletion of mscLpIma components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaRowStatusEntry

mscLpImaRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.22.1.1
A single entry in the table represents a single mscLpIma component.
OBJECT-TYPE    
  MscLpImaRowStatusEntry  

mscLpImaRowStatus 1.3.6.1.4.1.562.36.2.1.12.22.1.1.1
This variable is used as the basis for SNMP naming of mscLpIma components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscLpImaComponentName 1.3.6.1.4.1.562.36.2.1.12.22.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpImaStorageType 1.3.6.1.4.1.562.36.2.1.12.22.1.1.4
This variable represents the storage type value for the mscLpIma tables.
OBJECT-TYPE    
  StorageType  

mscLpImaIndex 1.3.6.1.4.1.562.36.2.1.12.22.1.1.10
This variable represents the index for the mscLpIma tables.
OBJECT-TYPE    
  Integer32 0..29  

mscLpImaTest 1.3.6.1.4.1.562.36.2.1.12.22.2
OBJECT IDENTIFIER    

mscLpImaTestRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.22.2.1
This entry controls the addition and deletion of mscLpImaTest components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaTestRowStatusEntry

mscLpImaTestRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.22.2.1.1
A single entry in the table represents a single mscLpImaTest component.
OBJECT-TYPE    
  MscLpImaTestRowStatusEntry  

mscLpImaTestRowStatus 1.3.6.1.4.1.562.36.2.1.12.22.2.1.1.1
This variable is used as the basis for SNMP naming of mscLpImaTest components. These components cannot be added nor deleted.
OBJECT-TYPE    
  RowStatus  

mscLpImaTestComponentName 1.3.6.1.4.1.562.36.2.1.12.22.2.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpImaTestStorageType 1.3.6.1.4.1.562.36.2.1.12.22.2.1.1.4
This variable represents the storage type value for the mscLpImaTest tables.
OBJECT-TYPE    
  StorageType  

mscLpImaTestIndex 1.3.6.1.4.1.562.36.2.1.12.22.2.1.1.10
This variable represents the index for the mscLpImaTest tables.
OBJECT-TYPE    
  NonReplicated  

mscLpImaTestStateTable 1.3.6.1.4.1.562.36.2.1.12.22.2.10
This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaTestStateEntry

mscLpImaTestStateEntry 1.3.6.1.4.1.562.36.2.1.12.22.2.10.1
An entry in the mscLpImaTestStateTable.
OBJECT-TYPE    
  MscLpImaTestStateEntry  

mscLpImaTestAdminState 1.3.6.1.4.1.562.36.2.1.12.22.2.10.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpImaTestOperationalState 1.3.6.1.4.1.562.36.2.1.12.22.2.10.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpImaTestUsageState 1.3.6.1.4.1.562.36.2.1.12.22.2.10.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpImaTestSetupTable 1.3.6.1.4.1.562.36.2.1.12.22.2.11
This group contains all of the operational data for a Test component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaTestSetupEntry

mscLpImaTestSetupEntry 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1
An entry in the mscLpImaTestSetupTable.
OBJECT-TYPE    
  MscLpImaTestSetupEntry  

mscLpImaTestPurpose 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.1
This attribute records the purpose of the test so that the test results can be associated and properly analyzed.
OBJECT-TYPE    
  AsciiString SIZE(0..40)  

mscLpImaTestType 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.2
This attribute is the type of test to be run. The available test types include the following: card test sets up an internal loop on the board and runs a bit error rate test. manual test assumes the line is looped back externally and a bit error rate test is performed. localLoop test loops back the local modem and performs a bit error rate test. remoteLoop test loops back the remote modem (or CSU) and performs a bit error rate test. externalLoop test loops back the line to the far end. payloadLoop test only loops back the payload data received from the incoming line. remoteLoopThisTrib loops this particular tributary back at the far end, using services provided by the parent. v54RemoteLoop initiates a V.54 Remote Loopback test. pn127RemoteLoop initiates a PN127 Remote Loopback test. Note that not all test types are not supported by all function processors.
OBJECT-TYPE    
  INTEGER card(0), manual(1), localLoop(2), remoteLoop(3), externalLoop(4), payloadLoop(5), remoteLoopThisTrib(6), v54RemoteLoop(7), pn127RemoteLoop(8)  

mscLpImaTestFrmSize 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.3
This attribute defines the size of the test data frames in number of bytes.
OBJECT-TYPE    
  Unsigned32 4..4096  

mscLpImaTestFrmPatternType 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.4
This attribute defines the type of data pattern generation to use. The following lists the available pattern types: ccitt32kBitPattern is a pseudo-random sequence of 32 kbit. ccitt8MBitPattern is a pseudo-random sequence of 8Mbit. customizedPattern is the pattern defined in the customizedPattern attribute.
OBJECT-TYPE    
  INTEGER ccitt32kBitPattern(0), ccitt8MBitPattern(1), customizedPattern(2)  

mscLpImaTestCustomizedPattern 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.5
This attribute allows a customized 32 bit pattern to be defined for use in the test data frames. This attribute is used when the attribute frmPatternType is set to CustomizedPattern. Note that a 55 hex pattern is an alternating 1 and 0 pattern.
OBJECT-TYPE    
  Hex 0..4294967295  

mscLpImaTestDataStartDelay 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.6
This attribute specifies the time delay (in seconds) between when the test expects the loop to have been set up, to when the test data actually starts to be transmitted. This attribute is to accommodate some non-standard equipment that requires extra time for setting up a requested loop. This attribute is ignored when the test type is set to externalLoop.
OBJECT-TYPE    
  Unsigned32 0..1814400  

mscLpImaTestDisplayInterval 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.7
This attribute defines the interval (in minutes) between which interim test results are to be displayed. Results are displayed at the operator console at which the test was started. When the test type is set to externalLoop, this attribute is ignored. There will be no display of results if displayInterval is set to 0. This attribute can be changed anytime.
OBJECT-TYPE    
  Unsigned32 0..30240  

mscLpImaTestDuration 1.3.6.1.4.1.562.36.2.1.12.22.2.11.1.8
This attribute is the duration (in minutes) that test data will be transmitted. In the case of an externalLoop, this is the time that the loop is in effect. Note that dataStartDelay does not apply to the externalLoop.
OBJECT-TYPE    
  Unsigned32 1..30240  

mscLpImaTestResultsTable 1.3.6.1.4.1.562.36.2.1.12.22.2.12
This group contains all the statistics related attributes of the Test component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaTestResultsEntry

mscLpImaTestResultsEntry 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1
An entry in the mscLpImaTestResultsTable.
OBJECT-TYPE    
  MscLpImaTestResultsEntry  

mscLpImaTestElapsedTime 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.1
This attribute is the number of minutes elapsed since the test started for an externalLoop test. For a data test, this is the time since test data was first transmitted.
OBJECT-TYPE    
  Counter32  

mscLpImaTestTimeRemaining 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.2
This attribute is the number of minutes remaining before the test is to be stopped according to the duration attribute.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaTestCauseOfTermination 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.3
This attribute indicates either the status of the test or the cause of the test's termination: neverStarted indicates that the test has not yet been started. testRunning indicates that the test has been started. stoppedByOperator indicates that the operator issued a stop command on a test that was running. testTimeExpired indicates that the test ran for the time specified by the test's duration. loopCodeSyncFailed indicates that the local end failed to synchronize to the loopCode pattern. The local end transmits the loopCode pattern to cause the remote end to apply a loopback, after which the local end should receive the loopCode pattern. The exact pattern used to request loopCode depends on the test type. This failure indicates a high rate of transmission errors, or that the remote end has failed to apply the loopback. patternSyncFailed indicates that the local end failed to synchronize to the frmPatternType test pattern, that should have been looped back at the remote end. This failure indicates a high rate of transmission errors or the absence of a loopback. patternSyncLost indicates that the local end gained and then lost synchronization to the returned frmPatternType test pattern. This failure indicates a sudden increase in transmission errors, frame slippage, or the removal of an existing loopback. unknown is set when a reason to terminate other than those listed here is encountered. Note: Only MSA cards support recognition of the failures loopCodeSyncFailed, patternSyncFailed and patternSyncLost. Other cards will not terminate the test under the conditions described by these values.
OBJECT-TYPE    
  INTEGER testTimeExpired(0), stoppedByOperator(1), unknown(2), neverStarted(3), testRunning(4), hardwareReconfigured(5), loopCodeSyncFailed(6), patternSyncFailed(7), patternSyncLost(8)  

mscLpImaTestBitsTx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.4
This attribute is the total number of bits sent during the test period. As long as the line speed of the hardware interface is less than 70 Mbit/s, this counter is not expected to reach the maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestBytesTx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.5
This attribute is the total number of bytes sent during the test period. This counter is not expected to reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestFrmTx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.6
This attribute is the total number of frames sent during the test period. This counter is not expected to reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestBitsRx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.7
This attribute is the total number of bits received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach the maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestBytesRx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.8
This attribute is the total number of bytes received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestFrmRx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.9
This attribute is the total number of frames received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestErroredFrmRx 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.10
This attribute is not displayed for ATM cards because the physical layer drops all errored frames at the controller interface. For all other card types, this attribute is the total number of errored frames received during the test period. This counter is not expected to reach its maximum value. The counter will wrap around to 0 if it does reach its maximum value.
OBJECT-TYPE    
  PassportCounter64  

mscLpImaTestBitErrorRate 1.3.6.1.4.1.562.36.2.1.12.22.2.12.1.11
This attribute is not displayed for ATM cards because the physical layer drops all errored frames at the controller interface. For all other card types, this attribute is the calculated bit error rate on the link. Test data are generated and sent in frames of a preset size (frameSize). The Test component will try to estimate the number of bit errors in any errored frame which is identifiable. The statistics will be updated accordingly. A lost frame (may be due to an error on the flag sequence) will be discarded for the bit error rate calculation. The result is presented in the form of xEsyy, where x is the mantissa, syy is the exponent, for example 0E+00, 2E-09. Note that the bitErrorRate is an estimate only. For more reliable test results, the test should be done over a long period. Multiple tests would also improve the confidence level of the test results.
OBJECT-TYPE    
  AsciiString SIZE(5)  

mscLpImaLk 1.3.6.1.4.1.562.36.2.1.12.22.3
OBJECT IDENTIFIER    

mscLpImaLkRowStatusTable 1.3.6.1.4.1.562.36.2.1.12.22.3.1
This entry controls the addition and deletion of mscLpImaLk components.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaLkRowStatusEntry

mscLpImaLkRowStatusEntry 1.3.6.1.4.1.562.36.2.1.12.22.3.1.1
A single entry in the table represents a single mscLpImaLk component.
OBJECT-TYPE    
  MscLpImaLkRowStatusEntry  

mscLpImaLkRowStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.1.1.1
This variable is used as the basis for SNMP naming of mscLpImaLk components. These components can be added and deleted.
OBJECT-TYPE    
  RowStatus  

mscLpImaLkComponentName 1.3.6.1.4.1.562.36.2.1.12.22.3.1.1.2
This variable provides the component's string name for use with the ASCII Console Interface
OBJECT-TYPE    
  DisplayString  

mscLpImaLkStorageType 1.3.6.1.4.1.562.36.2.1.12.22.3.1.1.4
This variable represents the storage type value for the mscLpImaLk tables.
OBJECT-TYPE    
  StorageType  

mscLpImaLkIndex 1.3.6.1.4.1.562.36.2.1.12.22.3.1.1.10
This variable represents the index for the mscLpImaLk tables.
OBJECT-TYPE    
  Integer32 0..31  

mscLpImaLkProvTable 1.3.6.1.4.1.562.36.2.1.12.22.3.10
This group contains the provisionable attributes for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaLkProvEntry

mscLpImaLkProvEntry 1.3.6.1.4.1.562.36.2.1.12.22.3.10.1
An entry in the mscLpImaLkProvTable.
OBJECT-TYPE    
  MscLpImaLkProvEntry  

mscLpImaLkInterfaceName 1.3.6.1.4.1.562.36.2.1.12.22.3.10.1.1
This attribute associates the Link subcomponent with a specific interface on a function processor, for example Lp/5 E1/3 Chan/0. If IMA groups and independent links coexist on a card running IMA and per-VC queueing is enabled, plan the selection of DS1 or E1 ports to be used by the IMA group carefully. For a 4pDS3ChAtm function processor there is no per-VC queueing.
OBJECT-TYPE    
  Link  

mscLpImaLkOperTable 1.3.6.1.4.1.562.36.2.1.12.22.3.11
This group contains the operational attributes for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaLkOperEntry

mscLpImaLkOperEntry 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1
An entry in the mscLpImaLkOperTable.
OBJECT-TYPE    
  MscLpImaLkOperEntry  

mscLpImaLkFailureCause 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1.1
This attribute indicates the failure cause on this link. Possible values are: noFailure: there is no failure on this link. interfaceDown: the physical port used by the link is down. lif: the link is in loss of IMA frame (LIF) state. lods: the link is in loss of delay synchronization (LODS) state; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group. It must be noted that hysteresis is used for the LODS condition. protocolError: the link is down because of a time-out or because bad values are being received in IMA Control Protocol (ICP) cells. remoteFailure: the far end link is down. misconnected: the link is down because the IMA group has declared, after using its transmit test pattern procedure, that this link is not properly connected. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedFrameLength: the link is down because it is receiving from the far end a frame length which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedSymmetry: the link is down because it is receiving from the far end a group symmetry which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. noIcp: the link is down because it is not receiving IMA Control Protocol (ICP) cells. This value can occur only if the protocol for the IMA group is atmForum10.
OBJECT-TYPE    
  INTEGER noFailure(0), interfaceDown(1), lif(2), lods(3), protocolError(4), remoteFailure(5), misconnected(6), unsupportedFrameLength(7), unsupportedSymmetry(8), noIcp(9)  

mscLpImaLkRemoteDefect 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1.2
This attribute indicates the IMA remote defect indicator (RDI) currently being received on this link. Possible values are: noDefect: no defect. physicalLayerDefect: the interface used by the remote link has a physical layer defect. This value can occur only if the protocol for the IMA group is atmForum10. interfaceDown: the physical interface used by the remote link is down.This value can occur only if the protocol for the IMA group is proprietary. lif: the remote link has a loss of IMA frame (LIF) defect. lods: the remote link has a loss of delay synchronization (LODS) defect; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group.
OBJECT-TYPE    
  INTEGER noDefect(0), physicalLayerDefect(1), lif(2), lods(3), interfaceDown(4)  

mscLpImaLkRemoteLid 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1.3
This attribute indicates the link identifier (LID) used by the remote IMA group on the physical link. A value of 0 will be displayed if the link is not receiving IMA Control Protocol (ICP) cells or if the physical layer is down.
OBJECT-TYPE    
  Unsigned32 0..31  

mscLpImaLkRelativeDelay 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1.4
This attribute indicates the latest measured differential delay (rounded up in milliseconds) between this link and the link, in the same IMA group, having the least delay. A value of 4294967295 indicates that the relative delay could not be measured. This can be due to physical layer problems or to no IMA Control Protocol (ICP) cells being received on the link.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaLkLastOifCause 1.3.6.1.4.1.562.36.2.1.12.22.3.11.1.5
This attribute indicates the cause of the last out of IMA frame (OIF) anomaly on the link. It will always have a value of noOif if the protocol for the IMA group is proprietary. Possible values are: noOif: no OIF was detected. badFrameLength: an IMA Control Protocol (ICP) cell with an unexpected frame length was received. badGid: an ICP cell with an unexpected group identifier (GID) was received. badLid: an ICP cell with an unexpected link identifier (LID) was received. badOffset: an ICP cell with an unexpected cell offset was received. badSequenceNumber: an ICP cell with an unexpected frame sequence number was received. stuffError: an illegal stuffing sequence was received. missingIcp: an expected ICP cell was not received. unexpectedIcp: an unexpected ICP cell was received. erroredIcp: two consecutive errored ICP cells were received. noCells: no cells are being received on the link. idleCell: an idle cell was received on the link.
OBJECT-TYPE    
  INTEGER noOif(0), badFrameLength(1), badGid(2), badLid(3), badOffset(4), badSequenceNumber(5), stuffError(6), missingIcp(7), unexpectedIcp(8), erroredIcp(9), noCells(10), idleCell(11)  

mscLpImaLkStatsTable 1.3.6.1.4.1.562.36.2.1.12.22.3.12
This group contains the statistics data for the Link subcomponent.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaLkStatsEntry

mscLpImaLkStatsEntry 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1
An entry in the mscLpImaLkStatsTable.
OBJECT-TYPE    
  MscLpImaLkStatsEntry  

mscLpImaLkRunningTime 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.1
This attribute counts the length of time (in seconds) for which the Link component has been running.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaLkUnavailSecs 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.2
For an IMA group whose protocol is atmForum10, this attribute counts the number of unavailable seconds. Unavailability begins at the start of 10 contiguous severely errored seconds (SES) and ends at the start of 10 contiguous seconds with no SES. For an IMA group whose protocol is proprietary, this attribute counts the number of one second intervals during which the Link component has been out of service.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaLkFailures 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.3
This attribute counts the number of failures, during link addition or normal operation, that the link has experienced.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaLkUnusableSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.4
This attribute counts the number of one second intervals during which the near end has been in an unusable state. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkSevErroredSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.5
This attribute counts the number of one second intervals in which at least 30 percent of the IMA Control Protocol (ICP) cells were counted as ICP violations or at least one link defect (physical layer, LIF and LODS defects) was detected. This attribute will not increment during UAS (Unavailable Second) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkFarEndUnusableSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.6
This attribute counts the number of one second intervals during which the 'Tx/Rx Unusable' condition has been received from the far end. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkFarEndSevErroredSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.7
This attribute counts the number of one second intervals containing one or more RDI defects. This attribute will not increment during FEUAS (Far-End Unavailable Second) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkFarEndUnavailSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.8
This attribute counts the number of unavailable seconds at the far end. Unavailability begins at the start of 10 contiguous severely errored seconds (SES) at the far end and ends at the start of 10 contiguous seconds at the far end with no SES. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkIcpViolations 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.9
This attribute counts the number of errored, invalid or missing IMA Control Protocol (ICP) cells during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkTxStuffEvents 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.10
This attribute counts the number of Stuff events transmitted during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkRxStuffEvents 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.11
This attribute counts the number of Stuff events received during non-SES (Severely Errored Second) and non-UAS (Unavailable Seconds) conditions. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkIdleCellSec 1.3.6.1.4.1.562.36.2.1.12.22.3.12.1.12
This attributes counts the number of one second intervals during which one or more idle cells was received. The reception of idle cells is an abnormal condition which could be caused by the remote IMA using the Common Transmit Clock mode with ports whose clock sources are not synchronized. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Counter32  

mscLpImaLkStateTable 1.3.6.1.4.1.562.36.2.1.12.22.3.13
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaLkStateEntry

mscLpImaLkStateEntry 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1
An entry in the mscLpImaLkStateTable.
OBJECT-TYPE    
  MscLpImaLkStateEntry  

mscLpImaLkAdminState 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpImaLkOperationalState 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpImaLkUsageState 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpImaLkAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscLpImaLkProceduralStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaLkControlStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaLkAlarmStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaLkStandbyStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscLpImaLkUnknownStatus 1.3.6.1.4.1.562.36.2.1.12.22.3.13.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

mscLpImaProvTable 1.3.6.1.4.1.562.36.2.1.12.22.10
This group contains the provisionable attributes for the Ima component. The default values of linkSelectionCriterion and linkRetryTimeout depend on card type.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaProvEntry

mscLpImaProvEntry 1.3.6.1.4.1.562.36.2.1.12.22.10.1
An entry in the mscLpImaProvTable.
OBJECT-TYPE    
  MscLpImaProvEntry  

mscLpImaLinkSelectionCriterion 1.3.6.1.4.1.562.36.2.1.12.22.10.1.1
This attribute specifies the method to be used by the IMA group when selecting links to be activated. This comes into effect only when the configured links do not respect the maximum differential delay (otherwise all links are accepted). If leastDelay is chosen, first the link having the smallest delay is selected as the reference link. The IMA group includes all links which respect the maximum differential delay relative to the reference link. If maxBandwidth is chosen, the IMA group selects the maximum possible number of links, with each selected link respecting the maximum differential delay relative to every other selected link. When more than one possibility exists, the combination which offers the least delay isselected. The default value for Multi-Service Access cards is leastDelay, and for all other cards is maxBandwidth. On Multi-Service Access cards leastDelay is the only acceptable provisionable value.
OBJECT-TYPE    
  INTEGER leastDelay(0), maxBandwidth(1)  

mscLpImaMaxDiffDelay 1.3.6.1.4.1.562.36.2.1.12.22.10.1.2
This attribute specifies the maximum differential delay between links acceptable in the IMA group. If a link violates that maximum differential delay, it will not be active in the IMA group and an alarm will be generated.
OBJECT-TYPE    
  Unsigned32 1..100  

mscLpImaLinkRetryTimeout 1.3.6.1.4.1.562.36.2.1.12.22.10.1.3
This attribute specifies the amount of time before reactivation of a link is attempted after it recovers from a failure condition. The default value for Multi-Service Access cards is 1, and for all other cards is 10. On Multi-Service Access cards 1 is the only acceptable provisionable value.
OBJECT-TYPE    
  Unsigned32 0..1000  

mscLpImaApplicationFramerName 1.3.6.1.4.1.562.36.2.1.12.22.10.1.4
This attribute defines the link to the AtmIf component using the Ima. An example is AtmIf/31.
OBJECT-TYPE    
  Link  

mscLpImaTransmitClockMode 1.3.6.1.4.1.562.36.2.1.12.22.10.1.5
This attribute specifies the transmit clocking mode. If itc (Independent Transmit Clock) is chosen, the physical ports used by the IMA group may have different clocking sources. If ctc (Common Transmit Clock) is chosen, it is recommended that the physical ports used by the IMA group have the same clocking source. However, if the physical ports have different clocking sources, the operator should ensure that all the clocking sources have the same rate.
OBJECT-TYPE    
  INTEGER itc(0), ctc(1)  

mscLpImaProtocol 1.3.6.1.4.1.562.36.2.1.12.22.10.1.6
This attribute specifies what protocol the component should run. If atmForum10 is chosen, the ATM Forum's IMA protocol (version 1.0) will be used and signalled in outgoing IMA Control Protocol (ICP) cells. This protocol is specified in version 1.1 of the ATM Forum IMA specification. The IMA group will come up only if the far end IMA also uses the ATM Forum's IMA protocol. If proprietary is chosen, Nortel's proprietary IMA protocol will be used. The IMA group will come up only if the far end IMA also uses Nortel's proprietary IMA protocol. This IMA group will not inter-operate with IMA implementations from other vendors. Feature ima must be provisioned on the LP for this protocol to be used.
OBJECT-TYPE    
  INTEGER atmForum10(0), proprietary(1)  

mscLpImaOperTable 1.3.6.1.4.1.562.36.2.1.12.22.11
This group contains the operational attributes for the Ima component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaOperEntry

mscLpImaOperEntry 1.3.6.1.4.1.562.36.2.1.12.22.11.1
An entry in the mscLpImaOperTable.
OBJECT-TYPE    
  MscLpImaOperEntry  

mscLpImaFailureCause 1.3.6.1.4.1.562.36.2.1.12.22.11.1.1
This attribute indicates the cause of the current local end failure experienced by the IMA group. The failure may have occurred during a start-up procedure or during normal operation. Possible values are: noFailure: no local end failure. noGoodLinksInStartup: no good links were available during IMA start-up. badGidInStartup: during start-up, different group identifiers (GIDs) were received on the links. badLidInStartup: during start-up, duplicate link identifiers (LIDs) were received on the links. unsupportedFrameLengthInStartup: during start-up, an unsupported frame length was received. timeoutInStartup: a time-out has occurred during start-up. noGoodLinks: no good links are available in the IMA group. remoteFailure: the far end is down. unsupportedSymmetryInStartup: the symmetry proposed by the far end is not supported on the near-end. This value will occur when the IMA group is running the ATM Forum protocol and the far end is proposing a group symmetry other than 'symmetric configuration and operation'.
OBJECT-TYPE    
  INTEGER noFailure(0), noGoodLinksInStartup(1), badGidInStartup(2), badLidInStartup(3), unsupportedFrameLengthInStartup(4), timeoutInStartup(5), noGoodLinks(6), remoteFailure(7), unsupportedSymmetryInStartup(8)  

mscLpImaRemoteDefect 1.3.6.1.4.1.562.36.2.1.12.22.11.1.2
This attribute indicates the cause of the current far end defect experienced by the IMA group. For the ATM Forum IMA protocol, possible values are: noDefect: no defect. unsupportedFrameLengthInStartup: during the far end's start-up, an unsupported frame length was received. unsupportedSymmetryInStartup: during the far end's start-up, an unsupported symmetry configuration was received. otherAbortStartup: the far end has aborted its start-up for another reason. This could be because different Gids were received on the links or if duplicate link identifiers (LIDs) were received. insufficientLinks: the far end does not have sufficient links active. This value will be displayed if the far end IMA group is locked. blocked: the far end IMA group is blocked. For the proprietary IMA protocol, possible values are: noDefect: no defect. noGoodLinksInStartup: no good links were available during the far end's start-up. badGidInStartup: during the far end's start-up, different GIDs were received on the links. badLidInStartup: during the far end's start-up, duplicate link identifiers (LIDs) were received on the links. unsupportedFrameLengthInStartup: during the far end's start-up, an unsupported frame length was received. timeoutInStartup: a time out has occurred during the far end's start- up. noGoodLinks: no good links are available in the far end IMA group. locked: the far end IMA group is locked.
OBJECT-TYPE    
  INTEGER noDefect(0), noGoodLinksInStartup(1), badGidInStartup(2), badLidInStartup(3), unsupportedFrameLengthInStartup(4), timeoutInStartup(5), noGoodLinks(6), locked(7), unsupportedSymmetryInStartup(8), otherAbortStartup(9), insufficientLinks(10), blocked(11)  

mscLpImaRemoteLidsConfig 1.3.6.1.4.1.562.36.2.1.12.22.11.1.3
This attribute indicates all the links which have been configured in the remote IMA group. For example, if links 1, 3 and 5 have been configured in the remote IMA group, this attribute would contain 1 3 5. Description of bits: n0(0) n1(1) n2(2) n3(3) n4(4) n5(5) n6(6) n7(7) n8(8) n9(9) n10(10) n11(11) n12(12) n13(13) n14(14) n15(15) n16(16) n17(17) n18(18) n19(19) n20(20) n21(21) n22(22) n23(23) n24(24) n25(25) n26(26) n27(27) n28(28) n29(29) n30(30) n31(31)
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

mscLpImaRemoteLidsActive 1.3.6.1.4.1.562.36.2.1.12.22.11.1.4
This attribute indicates all the links which are active in the remote IMA group. For example, if links 1 and 5 are active in the remote IMA, this attribute would contain 1 5. Description of bits: n0(0) n1(1) n2(2) n3(3) n4(4) n5(5) n6(6) n7(7) n8(8) n9(9) n10(10) n11(11) n12(12) n13(13) n14(14) n15(15) n16(16) n17(17) n18(18) n19(19) n20(20) n21(21) n22(22) n23(23) n24(24) n25(25) n26(26) n27(27) n28(28) n29(29) n30(30) n31(31)
OBJECT-TYPE    
  OCTET STRING SIZE(4)  

mscLpImaCellCapacity 1.3.6.1.4.1.562.36.2.1.12.22.11.1.5
This attribute indicates the total cell capacity (in cells per second) which is provided to the ATM layer. This cell capacity takes into account the physical and IMA level overheads.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaRemoteGid 1.3.6.1.4.1.562.36.2.1.12.22.11.1.6
This attribute indicates the IMA group identifier (GID) used by the remote IMA. A value of 0 will be displayed if the group is not receiving IMA Control Protocol (ICP) cells. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Unsigned32 0..255  

mscLpImaClockingModeMismatch 1.3.6.1.4.1.562.36.2.1.12.22.11.1.7
This attribute indicates whether or not both ends of the IMA group are using the same transmit clocking mode (itc/ctc). Its value will be yes if both ends are not using the same transmit clocking mode. A clocking mode mismatch does not prevent an IMA group from coming up and can be corrected by using the same clocking mode at both ends. This attribute will always have a value of no if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

mscLpImaStatsTable 1.3.6.1.4.1.562.36.2.1.12.22.12
This group contains the statistics data for the Ima component.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaStatsEntry

mscLpImaStatsEntry 1.3.6.1.4.1.562.36.2.1.12.22.12.1
An entry in the mscLpImaStatsTable.
OBJECT-TYPE    
  MscLpImaStatsEntry  

mscLpImaRunningTime 1.3.6.1.4.1.562.36.2.1.12.22.12.1.1
This attribute indicates the length of time (in seconds) for which the Ima component has been in the unlocked state or has been used for operational testing.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaUnavailSecs 1.3.6.1.4.1.562.36.2.1.12.22.12.1.2
This attribute indicates the number of one second intervals during which the Ima component has been unlocked and out of service.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaFailures 1.3.6.1.4.1.562.36.2.1.12.22.12.1.3
This attribute indicates the number of complete failures, during start-up or normal operation, that the Ima component has experienced since being added. It must be noted that a service degradation, such as 1 of the 3 links in an IMA group being down, is not counted as a failure. If an Ima component is in a failure loop and does not come up, this count will only increase by 1.
OBJECT-TYPE    
  Unsigned32 0..4294967295  

mscLpImaReceiveCellUtilization 1.3.6.1.4.1.562.36.2.1.12.22.12.1.4
This attribute indicates the ratio of the number of valid, assigned user cells received on the IMA group to the IMA cell capacity (based on the number of active links). The utilization is calculated over a one minute period. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Gauge32 0..100  

mscLpImaTransmitCellUtilization 1.3.6.1.4.1.562.36.2.1.12.22.12.1.5
This attribute indicates the ratio of the number of user cells transmitted on the IMA group to the IMA cell capacity (based on the number of active links). The utilization is calculated over a one minute period. This attribute will always have a value of 0 if the protocol for the IMA group is proprietary.
OBJECT-TYPE    
  Gauge32 0..100  

mscLpImaCidDataTable 1.3.6.1.4.1.562.36.2.1.12.22.13
This group contains the attribute for a component's Customer Identifier (CID). Refer to the attribute description for a detailed explanation of CIDs.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaCidDataEntry

mscLpImaCidDataEntry 1.3.6.1.4.1.562.36.2.1.12.22.13.1
An entry in the mscLpImaCidDataTable.
OBJECT-TYPE    
  MscLpImaCidDataEntry  

mscLpImaCustomerIdentifier 1.3.6.1.4.1.562.36.2.1.12.22.13.1.1
This attribute holds the Customer Identifier (CID). Every component has a CID. If a component has a cid attribute, the component's CID is the provisioned value of that attribute; otherwise the component inherits the CID of its parent. The top- level component has a CID of 0. Every operator session also has a CID, which is the CID provisioned for the operator's user ID. An operator will see only the stream data for components having a matching CID. Also, the operator will be allowed to issue commands for only those components which have a matching CID. An operator CID of 0 is used to identify the Network Manager (referred to as 'NetMan' in DPN). This CID matches the CID of any component. Values 1 to 8191 inclusive (equivalent to 'basic CIDs' in DPN) may be assigned to specific customers.
OBJECT-TYPE    
  Unsigned32 0 | 1..8191  

mscLpImaStateTable 1.3.6.1.4.1.562.36.2.1.12.22.14
This group contains the three OSI State attributes and the six OSI Status attributes. The descriptions generically indicate what each attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241- 7001-150, Passport Operations and Maintenance Guide.
OBJECT-TYPE    
  SEQUENCE OF  
    MscLpImaStateEntry

mscLpImaStateEntry 1.3.6.1.4.1.562.36.2.1.12.22.14.1
An entry in the mscLpImaStateTable.
OBJECT-TYPE    
  MscLpImaStateEntry  

mscLpImaAdminState 1.3.6.1.4.1.562.36.2.1.12.22.14.1.1
This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER locked(0), unlocked(1), shuttingDown(2)  

mscLpImaOperationalState 1.3.6.1.4.1.562.36.2.1.12.22.14.1.2
This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

mscLpImaUsageState 1.3.6.1.4.1.562.36.2.1.12.22.14.1.3
This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time. The OSI Status attributes, if supported by the component, may provide more details, qualifying the state of the component.
OBJECT-TYPE    
  INTEGER idle(0), active(1), busy(2)  

mscLpImaAvailabilityStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.4
If supported by the component, this attribute indicates the OSI Availability status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value inTest indicates that the resource is undergoing a test procedure. If adminState is locked or shuttingDown, the normal users are precluded from using the resource and controlStatus is reservedForTest. Tests that do not exclude additional users can be present in any operational or administrative state but the reservedForTest condition should not be present. The value failed indicates that the component has an internal fault that prevents it from operating. The operationalState is disabled. The value dependency indicates that the component cannot operate because some other resource on which it depends is unavailable. The operationalState is disabled. The value powerOff indicates the resource requires power to be applied and it is not powered on. The operationalState is disabled. The value offLine indicates the resource requires a routine operation (either manual, automatic, or both) to be performed to place it on-line and make it available for use. The operationalState is disabled. The value offDuty indicates the resource is inactive in accordance with a predetermined time schedule. In the absence of other disabling conditions, the operationalState is enabled or disabled. The value degraded indicates the service provided by the component is degraded in some way, such as in speed or operating capacity. However, the resource remains available for service. The operationalState is enabled. The value notInstalled indicates the resource is not present. The operationalState is disabled. The value logFull is not used. Description of bits: inTest(0) failed(1) powerOff(2) offLine(3) offDuty(4) dependency(5) degraded(6) notInstalled(7) logFull(8)
OBJECT-TYPE    
  OCTET STRING SIZE(2)  

mscLpImaProceduralStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.5
If supported by the component, this attribute indicates the OSI Procedural status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value initializationRequired indicates (for a resource which doesn't initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState is disabled. The value notInitialized indicates (for a resource which does initialize autonomously) that initialization is required before it can perform its normal functions, and this procedure has not been initiated. The operationalState may be enabled or disabled. The value initializing indicates that initialization has been initiated but is not yet complete. The operationalState may be enabled or disabled. The value reporting indicates the resource has completed some processing operation and is notifying the results. The operationalState is enabled. The value terminating indicates the component is in a termination phase. If the resource doesn't reinitialize autonomously, operationalState is disabled; otherwise it is enabled or disabled. Description of bits: initializationRequired(0) notInitialized(1) initializing(2) reporting(3) terminating(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaControlStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.6
If supported by the component, this attribute indicates the OSI Control status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value subjectToTest indicates the resource is available but tests may be conducted simultaneously at unpredictable times, which may cause it to exhibit unusual characteristics. The value partOfServicesLocked indicates that part of the service is restricted from users of a resource. The adminState is unlocked. The value reservedForTest indicates that the component is administratively unavailable because it is undergoing a test procedure. The adminState is locked. The value suspended indicates that the service has been administratively suspended. Description of bits: subjectToTest(0) partOfServicesLocked(1) reservedForTest(2) suspended(3)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaAlarmStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.7
If supported by the component, this attribute indicates the OSI Alarm status of the component. Note that, even though it is defined as a multi-valued set, at most one value is shown to the user. When no values are in the set, this indicates that either the attribute is not supported or that none of the status conditions described below are present. The value underRepair indicates the component is currently being repaired. The operationalState is enabled or disabled. The value critical indicates one or more critical alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value major indicates one or more major alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value minor indicates one or more minor alarms are outstanding against the component. Other, less severe, alarms may also be outstanding. The operationalState is enabled or disabled. The value alarmOutstanding generically indicates that an alarm of some severity is outstanding against the component. Description of bits: underRepair(0) critical(1) major(2) minor(3) alarmOutstanding(4)
OBJECT-TYPE    
  OCTET STRING SIZE(1)  

mscLpImaStandbyStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.8
If supported by the component, this attribute indicates the OSI Standby status of the component. The value notSet indicates that either the attribute is not supported or that none of the status conditions described below are present. Note that this is a non-standard value, used because the original specification indicated this attribute was set-valued and thus, did not provide a value to indicate that none of the other three are applicable. The value hotStandby indicates that the resource is not providing service but will be immediately able to take over the role of the resource to be backed up, without initialization activity, and containing the same information as the resource to be backed up. The value coldStandby indicates the resource is a backup for another resource but will not be immediately able to take over the role of the backed up resource and will require some initialization activity. The value providingService indicates that this component, as a backup resource, is currently backing up another resource.
OBJECT-TYPE    
  INTEGER hotStandby(0), coldStandby(1), providingService(2), notSet(15)  

mscLpImaUnknownStatus 1.3.6.1.4.1.562.36.2.1.12.22.14.1.9
This attribute indicates the OSI Unknown status of the component. The value false indicates that all of the other OSI State and Status attribute values can be considered accurate. The value true indicates that the actual state of the component is not known for sure.
OBJECT-TYPE    
  INTEGER false(0), true(1)  

imaMIB 1.3.6.1.4.1.562.36.2.2.115
OBJECT IDENTIFIER    

imaGroup 1.3.6.1.4.1.562.36.2.2.115.1
OBJECT IDENTIFIER    

imaGroupCA 1.3.6.1.4.1.562.36.2.2.115.1.1
OBJECT IDENTIFIER    

imaGroupCA02 1.3.6.1.4.1.562.36.2.2.115.1.1.3
OBJECT IDENTIFIER    

imaGroupCA02A 1.3.6.1.4.1.562.36.2.2.115.1.1.3.2
OBJECT IDENTIFIER    

imaCapabilities 1.3.6.1.4.1.562.36.2.2.115.3
OBJECT IDENTIFIER    

imaCapabilitiesCA 1.3.6.1.4.1.562.36.2.2.115.3.1
OBJECT IDENTIFIER    

imaCapabilitiesCA02 1.3.6.1.4.1.562.36.2.2.115.3.1.3
OBJECT IDENTIFIER    

imaCapabilitiesCA02A 1.3.6.1.4.1.562.36.2.2.115.3.1.3.2
OBJECT IDENTIFIER    

Defined Objects

MscLpDS3ImaRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpDS3ImaRowStatus  
  DisplayString as mscLpDS3ImaComponentName  
  StorageType as mscLpDS3ImaStorageType  
  Integer32 as mscLpDS3ImaIndex  

MscLpDS3ImaProvEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaLinkSelectionCriterion  
  Unsigned32 as mscLpDS3ImaMaxDiffDelay  
  Unsigned32 as mscLpDS3ImaLinkRetryTimeout  
  Link as mscLpDS3ImaApplicationFramerName  
  INTEGER as mscLpDS3ImaTransmitClockMode  
  INTEGER as mscLpDS3ImaProtocol  

MscLpDS3ImaOperEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaFailureCause  
  INTEGER as mscLpDS3ImaRemoteDefect  
  OCTET STRING as mscLpDS3ImaRemoteLidsConfig  
  OCTET STRING as mscLpDS3ImaRemoteLidsActive  
  Unsigned32 as mscLpDS3ImaCellCapacity  
  Unsigned32 as mscLpDS3ImaRemoteGid  
  INTEGER as mscLpDS3ImaClockingModeMismatch  

MscLpDS3ImaStatsEntry  
SEQUENCE    
  Unsigned32 as mscLpDS3ImaRunningTime  
  Unsigned32 as mscLpDS3ImaUnavailSecs  
  Unsigned32 as mscLpDS3ImaFailures  
  Gauge32 as mscLpDS3ImaReceiveCellUtilization  
  Gauge32 as mscLpDS3ImaTransmitCellUtilization  

MscLpDS3ImaCidDataEntry  
SEQUENCE    
  Unsigned32 as mscLpDS3ImaCustomerIdentifier  

MscLpDS3ImaStateEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaAdminState  
  INTEGER as mscLpDS3ImaOperationalState  
  INTEGER as mscLpDS3ImaUsageState  
  OCTET STRING as mscLpDS3ImaAvailabilityStatus  
  OCTET STRING as mscLpDS3ImaProceduralStatus  
  OCTET STRING as mscLpDS3ImaControlStatus  
  OCTET STRING as mscLpDS3ImaAlarmStatus  
  INTEGER as mscLpDS3ImaStandbyStatus  
  INTEGER as mscLpDS3ImaUnknownStatus  

MscLpDS3ImaTestRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpDS3ImaTestRowStatus  
  DisplayString as mscLpDS3ImaTestComponentName  
  StorageType as mscLpDS3ImaTestStorageType  
  NonReplicated as mscLpDS3ImaTestIndex  

MscLpDS3ImaTestStateEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaTestAdminState  
  INTEGER as mscLpDS3ImaTestOperationalState  
  INTEGER as mscLpDS3ImaTestUsageState  

MscLpDS3ImaTestSetupEntry  
SEQUENCE    
  AsciiString as mscLpDS3ImaTestPurpose  
  INTEGER as mscLpDS3ImaTestType  
  Unsigned32 as mscLpDS3ImaTestFrmSize  
  INTEGER as mscLpDS3ImaTestFrmPatternType  
  Hex as mscLpDS3ImaTestCustomizedPattern  
  Unsigned32 as mscLpDS3ImaTestDataStartDelay  
  Unsigned32 as mscLpDS3ImaTestDisplayInterval  
  Unsigned32 as mscLpDS3ImaTestDuration  

MscLpDS3ImaTestResultsEntry  
SEQUENCE    
  Counter32 as mscLpDS3ImaTestElapsedTime  
  Unsigned32 as mscLpDS3ImaTestTimeRemaining  
  INTEGER as mscLpDS3ImaTestCauseOfTermination  
  PassportCounter64 as mscLpDS3ImaTestBitsTx  
  PassportCounter64 as mscLpDS3ImaTestBytesTx  
  PassportCounter64 as mscLpDS3ImaTestFrmTx  
  PassportCounter64 as mscLpDS3ImaTestBitsRx  
  PassportCounter64 as mscLpDS3ImaTestBytesRx  
  PassportCounter64 as mscLpDS3ImaTestFrmRx  
  PassportCounter64 as mscLpDS3ImaTestErroredFrmRx  
  AsciiString as mscLpDS3ImaTestBitErrorRate  

MscLpDS3ImaLkRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpDS3ImaLkRowStatus  
  DisplayString as mscLpDS3ImaLkComponentName  
  StorageType as mscLpDS3ImaLkStorageType  
  Integer32 as mscLpDS3ImaLkIndex  

MscLpDS3ImaLkProvEntry  
SEQUENCE    
  Link as mscLpDS3ImaLkInterfaceName  

MscLpDS3ImaLkOperEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaLkFailureCause  
  INTEGER as mscLpDS3ImaLkRemoteDefect  
  Unsigned32 as mscLpDS3ImaLkRemoteLid  
  Unsigned32 as mscLpDS3ImaLkRelativeDelay  
  INTEGER as mscLpDS3ImaLkLastOifCause  

MscLpDS3ImaLkStatsEntry  
SEQUENCE    
  Unsigned32 as mscLpDS3ImaLkRunningTime  
  Unsigned32 as mscLpDS3ImaLkUnavailSecs  
  Unsigned32 as mscLpDS3ImaLkFailures  
  Counter32 as mscLpDS3ImaLkUnusableSec  
  Counter32 as mscLpDS3ImaLkSevErroredSec  
  Counter32 as mscLpDS3ImaLkFarEndUnusableSec  
  Counter32 as mscLpDS3ImaLkFarEndSevErroredSec  
  Counter32 as mscLpDS3ImaLkFarEndUnavailSec  
  Counter32 as mscLpDS3ImaLkIcpViolations  
  Counter32 as mscLpDS3ImaLkTxStuffEvents  
  Counter32 as mscLpDS3ImaLkRxStuffEvents  
  Counter32 as mscLpDS3ImaLkIdleCellSec  

MscLpDS3ImaLkStateEntry  
SEQUENCE    
  INTEGER as mscLpDS3ImaLkAdminState  
  INTEGER as mscLpDS3ImaLkOperationalState  
  INTEGER as mscLpDS3ImaLkUsageState  
  OCTET STRING as mscLpDS3ImaLkAvailabilityStatus  
  OCTET STRING as mscLpDS3ImaLkProceduralStatus  
  OCTET STRING as mscLpDS3ImaLkControlStatus  
  OCTET STRING as mscLpDS3ImaLkAlarmStatus  
  INTEGER as mscLpDS3ImaLkStandbyStatus  
  INTEGER as mscLpDS3ImaLkUnknownStatus  

MscLpImaRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpImaRowStatus  
  DisplayString as mscLpImaComponentName  
  StorageType as mscLpImaStorageType  
  Integer32 as mscLpImaIndex  

MscLpImaProvEntry  
SEQUENCE    
  INTEGER as mscLpImaLinkSelectionCriterion  
  Unsigned32 as mscLpImaMaxDiffDelay  
  Unsigned32 as mscLpImaLinkRetryTimeout  
  Link as mscLpImaApplicationFramerName  
  INTEGER as mscLpImaTransmitClockMode  
  INTEGER as mscLpImaProtocol  

MscLpImaOperEntry  
SEQUENCE    
  INTEGER as mscLpImaFailureCause  
  INTEGER as mscLpImaRemoteDefect  
  OCTET STRING as mscLpImaRemoteLidsConfig  
  OCTET STRING as mscLpImaRemoteLidsActive  
  Unsigned32 as mscLpImaCellCapacity  
  Unsigned32 as mscLpImaRemoteGid  
  INTEGER as mscLpImaClockingModeMismatch  

MscLpImaStatsEntry  
SEQUENCE    
  Unsigned32 as mscLpImaRunningTime  
  Unsigned32 as mscLpImaUnavailSecs  
  Unsigned32 as mscLpImaFailures  
  Gauge32 as mscLpImaReceiveCellUtilization  
  Gauge32 as mscLpImaTransmitCellUtilization  

MscLpImaCidDataEntry  
SEQUENCE    
  Unsigned32 as mscLpImaCustomerIdentifier  

MscLpImaStateEntry  
SEQUENCE    
  INTEGER as mscLpImaAdminState  
  INTEGER as mscLpImaOperationalState  
  INTEGER as mscLpImaUsageState  
  OCTET STRING as mscLpImaAvailabilityStatus  
  OCTET STRING as mscLpImaProceduralStatus  
  OCTET STRING as mscLpImaControlStatus  
  OCTET STRING as mscLpImaAlarmStatus  
  INTEGER as mscLpImaStandbyStatus  
  INTEGER as mscLpImaUnknownStatus  

MscLpImaTestRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpImaTestRowStatus  
  DisplayString as mscLpImaTestComponentName  
  StorageType as mscLpImaTestStorageType  
  NonReplicated as mscLpImaTestIndex  

MscLpImaTestStateEntry  
SEQUENCE    
  INTEGER as mscLpImaTestAdminState  
  INTEGER as mscLpImaTestOperationalState  
  INTEGER as mscLpImaTestUsageState  

MscLpImaTestSetupEntry  
SEQUENCE    
  AsciiString as mscLpImaTestPurpose  
  INTEGER as mscLpImaTestType  
  Unsigned32 as mscLpImaTestFrmSize  
  INTEGER as mscLpImaTestFrmPatternType  
  Hex as mscLpImaTestCustomizedPattern  
  Unsigned32 as mscLpImaTestDataStartDelay  
  Unsigned32 as mscLpImaTestDisplayInterval  
  Unsigned32 as mscLpImaTestDuration  

MscLpImaTestResultsEntry  
SEQUENCE    
  Counter32 as mscLpImaTestElapsedTime  
  Unsigned32 as mscLpImaTestTimeRemaining  
  INTEGER as mscLpImaTestCauseOfTermination  
  PassportCounter64 as mscLpImaTestBitsTx  
  PassportCounter64 as mscLpImaTestBytesTx  
  PassportCounter64 as mscLpImaTestFrmTx  
  PassportCounter64 as mscLpImaTestBitsRx  
  PassportCounter64 as mscLpImaTestBytesRx  
  PassportCounter64 as mscLpImaTestFrmRx  
  PassportCounter64 as mscLpImaTestErroredFrmRx  
  AsciiString as mscLpImaTestBitErrorRate  

MscLpImaLkRowStatusEntry  
SEQUENCE    
  RowStatus as mscLpImaLkRowStatus  
  DisplayString as mscLpImaLkComponentName  
  StorageType as mscLpImaLkStorageType  
  Integer32 as mscLpImaLkIndex  

MscLpImaLkProvEntry  
SEQUENCE    
  Link as mscLpImaLkInterfaceName  

MscLpImaLkOperEntry  
SEQUENCE    
  INTEGER as mscLpImaLkFailureCause  
  INTEGER as mscLpImaLkRemoteDefect  
  Unsigned32 as mscLpImaLkRemoteLid  
  Unsigned32 as mscLpImaLkRelativeDelay  
  INTEGER as mscLpImaLkLastOifCause  

MscLpImaLkStatsEntry  
SEQUENCE    
  Unsigned32 as mscLpImaLkRunningTime  
  Unsigned32 as mscLpImaLkUnavailSecs  
  Unsigned32 as mscLpImaLkFailures  
  Counter32 as mscLpImaLkUnusableSec  
  Counter32 as mscLpImaLkSevErroredSec  
  Counter32 as mscLpImaLkFarEndUnusableSec  
  Counter32 as mscLpImaLkFarEndSevErroredSec  
  Counter32 as mscLpImaLkFarEndUnavailSec  
  Counter32 as mscLpImaLkIcpViolations  
  Counter32 as mscLpImaLkTxStuffEvents  
  Counter32 as mscLpImaLkRxStuffEvents  
  Counter32 as mscLpImaLkIdleCellSec  

MscLpImaLkStateEntry  
SEQUENCE    
  INTEGER as mscLpImaLkAdminState  
  INTEGER as mscLpImaLkOperationalState  
  INTEGER as mscLpImaLkUsageState  
  OCTET STRING as mscLpImaLkAvailabilityStatus  
  OCTET STRING as mscLpImaLkProceduralStatus  
  OCTET STRING as mscLpImaLkControlStatus  
  OCTET STRING as mscLpImaLkAlarmStatus  
  INTEGER as mscLpImaLkStandbyStatus  
  INTEGER as mscLpImaLkUnknownStatus