OSPFV3-MIB-JUNIPER

File: OSPFV3-MIB-JUNIPER.mib (133334 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB INET-ADDRESS-MIB OSPF-MIB
JUNIPER-EXPERIMENT-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
mib-2 Counter32 Gauge32
Integer32 Unsigned32 TEXTUAL-CONVENTION
TruthValue RowStatus MODULE-COMPLIANCE
OBJECT-GROUP NOTIFICATION-GROUP InterfaceIndex
InetAddressType InetAddress InetAddressPrefixLength
Metric BigMetric Status
HelloRange DesignatedRouterPriority jnxOspfv3Experiment

Defined Objects

jnxOspfv3MIB 1.3.6.1.4.1.2636.5.4.1
The MIB module for OSPF version 3. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices.
MODULE-IDENTITY    

jnxOspfv3Notifications 1.3.6.1.4.1.2636.5.4.1.0
OBJECT IDENTIFIER    

jnxOspfv3VirtIfStateChange 1.3.6.1.4.1.2636.5.4.1.0.1
An ospfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point).
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3VirtIfState  

jnxOspfv3NbrStateChange 1.3.6.1.4.1.2636.5.4.1.0.2
An ospfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3NbrState  

jnxOspfv3VirtNbrStateChange 1.3.6.1.4.1.2636.5.4.1.0.3
An ospfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full).
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3VirtNbrState  

jnxOspfv3IfConfigError 1.3.6.1.4.1.2636.5.4.1.0.4
An ospfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3IfState  
  jnxOspfv3PacketSrc  
  jnxOspfv3ConfigErrorType  
  jnxOspfv3PacketType  

jnxOspfv3VirtIfConfigError 1.3.6.1.4.1.2636.5.4.1.0.5
An ospfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3VirtIfState  
  jnxOspfv3ConfigErrorType  
  jnxOspfv3PacketType  

jnxOspfv3IfRxBadPacket 1.3.6.1.4.1.2636.5.4.1.0.6
An ospfv3IfRxBadPacket notification signifies that an ospfv3 packet that cannot be parsed has been received on a non-virtual interface.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3IfState  
  jnxOspfv3PacketSrc  
  jnxOspfv3PacketType  

jnxOspfv3VirtIfRxBadPacket 1.3.6.1.4.1.2636.5.4.1.0.7
An ospfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3VirtIfState  
  jnxOspfv3PacketType  

jnxOspfv3LsdbOverflow 1.3.6.1.4.1.2636.5.4.1.0.8
An ospfv3LsdbOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ospfv3ExtAreaLsdbLimit.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3ExtAreaLsdbLimit  

jnxOspfv3LsdbApproachingOverflow 1.3.6.1.4.1.2636.5.4.1.0.9
An ospfv3LsdbApproachingOverflow notification signifies that the number of LSAs in the router's link-state database has exceeded ninety percent of ospfv3ExtAreaLsdbLimit.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3ExtAreaLsdbLimit  

jnxOspfv3IfStateChange 1.3.6.1.4.1.2636.5.4.1.0.10
An ospfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup).
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3IfState  

jnxOspfv3NssaTranslatorStatusChange 1.3.6.1.4.1.2636.5.4.1.0.11
An ospfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per area basis.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3AreaNssaTranslatorState  

jnxOspfv3RestartStatusChange 1.3.6.1.4.1.2636.5.4.1.0.12
An ospfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3RestartStatus  
  jnxOspfv3RestartInterval  
  jnxOspfv3RestartExitRc  

jnxOspfv3NbrRestartHelperStatusChange 1.3.6.1.4.1.2636.5.4.1.0.13
An ospfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3NbrRestartHelperStatus  
  jnxOspfv3NbrRestartHelperAge  
  jnxOspfv3NbrRestartHelperExitRc  

jnxOspfv3VirtNbrRestartHelperStatusChange 1.3.6.1.4.1.2636.5.4.1.0.14
An ospfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor.
NOTIFICATION-TYPE    
  jnxOspfv3RouterId  
  jnxOspfv3VirtNbrRestartHelperStatus  
  jnxOspfv3VirtNbrRestartHelperAge  
  jnxOspfv3VirtNbrRestartHelperExitRc  

jnxOspfv3Objects 1.3.6.1.4.1.2636.5.4.1.1
OBJECT IDENTIFIER    

jnxOspfv3GeneralGroup 1.3.6.1.4.1.2636.5.4.1.1.1
OBJECT IDENTIFIER    

jnxOspfv3RouterId 1.3.6.1.4.1.2636.5.4.1.1.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3AdminStat 1.3.6.1.4.1.2636.5.4.1.1.1.2
The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces.
OBJECT-TYPE    
  Status  

jnxOspfv3VersionNumber 1.3.6.1.4.1.2636.5.4.1.1.1.3
The version number of OSPF for IPv6 is 3.
OBJECT-TYPE    
  INTEGER version3(3)  

jnxOspfv3AreaBdrRtrStatus 1.3.6.1.4.1.2636.5.4.1.1.1.4
A flag to note whether this router is an area border router.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3ASBdrRtrStatus 1.3.6.1.4.1.2636.5.4.1.1.1.5
A flag to note whether this router is configured as an Autonomous System border router.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3AsScopeLsaCount 1.3.6.1.4.1.2636.5.4.1.1.1.6
The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3AsScopeLsaCksumSum 1.3.6.1.4.1.2636.5.4.1.1.1.7
The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

jnxOspfv3OriginateNewLsas 1.3.6.1.4.1.2636.5.4.1.1.1.8
The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
OBJECT-TYPE    
  Counter32  

jnxOspfv3RxNewLsas 1.3.6.1.4.1.2636.5.4.1.1.1.9
The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements.
OBJECT-TYPE    
  Counter32  

jnxOspfv3ExtLsaCount 1.3.6.1.4.1.2636.5.4.1.1.1.10
The number of External(LS type 0x4005) in the link state database
OBJECT-TYPE    
  Gauge32  

jnxOspfv3ExtAreaLsdbLimit 1.3.6.1.4.1.2636.5.4.1.1.1.11
The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. Ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded).
OBJECT-TYPE    
  Integer32 -1..'7FFFFFFF'h  

jnxOspfv3MulticastExtensions 1.3.6.1.4.1.2636.5.4.1.1.1.12
A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multicast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area multicast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Autonomous Systems (called inter-AS multicast routing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared.
OBJECT-TYPE    
  BITS intraAreaMulticast(0), interAreaMulticast(1), interAsMulticast(2)  

jnxOspfv3ExitOverflowInterval 1.3.6.1.4.1.2636.5.4.1.1.1.13
The number of seconds that, after entering Overflow State, a router will attempt to leave Overflow State. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow State until restarted.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3DemandExtensions 1.3.6.1.4.1.2636.5.4.1.1.1.14
The router's support for demand routing.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3ReferenceBandwidth 1.3.6.1.4.1.2636.5.4.1.1.1.15
Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS)
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3RestartSupport 1.3.6.1.4.1.2636.5.4.1.1.1.16
The router's support for OSPF Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts.
OBJECT-TYPE    
  INTEGER none(1), plannedOnly(2), plannedAndUnplanned(3)  

jnxOspfv3RestartInterval 1.3.6.1.4.1.2636.5.4.1.1.1.17
Configured OSPF Graceful restart timeout interval.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3RestartStatus 1.3.6.1.4.1.2636.5.4.1.1.1.18
The current status of OSPF Graceful restart capability.
OBJECT-TYPE    
  INTEGER notRestarting(1), plannedRestart(2), unplannedRestart(3)  

jnxOspfv3RestartAge 1.3.6.1.4.1.2636.5.4.1.1.1.19
Remaining time in current OSPF Graceful restart interval.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3RestartExitRc 1.3.6.1.4.1.2636.5.4.1.1.1.20
Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

jnxOspfv3NotificationEnable 1.3.6.1.4.1.2636.5.4.1.1.1.21
If this object is set to true(1), then it enables the generation of OSPFv3 Notifications. If it is set to false(2), these notifications are not generated. Configured values MUST survive an agent reboot.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3AreaTable 1.3.6.1.4.1.2636.5.4.1.1.2
Information describing the configured parameters and cumulative statistics of the router's attached areas.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3AreaEntry

jnxOspfv3AreaEntry 1.3.6.1.4.1.2636.5.4.1.1.2.1
Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
OBJECT-TYPE    
  JnxOspfv3AreaEntry  

jnxOspfv3AreaId 1.3.6.1.4.1.2636.5.4.1.1.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3ImportAsExtern 1.3.6.1.4.1.2636.5.4.1.1.2.1.2
Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope
OBJECT-TYPE    
  INTEGER importExternal(1), importNoExternal(2), importNssa(3)  

jnxOspfv3AreaSpfRuns 1.3.6.1.4.1.2636.5.4.1.1.2.1.3
The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm.
OBJECT-TYPE    
  Counter32  

jnxOspfv3AreaBdrRtrCount 1.3.6.1.4.1.2636.5.4.1.1.2.1.4
The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3AreaAsBdrRtrCount 1.3.6.1.4.1.2636.5.4.1.1.2.1.5
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3AreaScopeLsaCount 1.3.6.1.4.1.2636.5.4.1.1.2.1.6
The total number of Area-Scope link state advertisements in this area's link state database.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3AreaScopeLsaCksumSum 1.3.6.1.4.1.2636.5.4.1.1.2.1.7
The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AreaSummary 1.3.6.1.4.1.2636.5.4.1.1.2.1.8
The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs.
OBJECT-TYPE    
  INTEGER noAreaSummary(1), sendAreaSummary(2)  

jnxOspfv3AreaStatus 1.3.6.1.4.1.2636.5.4.1.1.2.1.9
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3StubMetric 1.3.6.1.4.1.2636.5.4.1.1.2.1.10
The metric value advertised for the default route into Stub and NSSA areas.
OBJECT-TYPE    
  BigMetric  

jnxOspfv3AreaNssaTranslatorRole 1.3.6.1.4.1.2636.5.4.1.1.2.1.11
Indicates an NSSA Border router's ability to perform NSSA translation of NSSA-LSAs into AS-External-LSAs.
OBJECT-TYPE    
  INTEGER always(1), candidate(2)  

jnxOspfv3AreaNssaTranslatorState 1.3.6.1.4.1.2636.5.4.1.1.2.1.12
Indicates if and how an NSSA Border router is performing NSSA translation of NSSA-LSAs into AS-External-LSA's. When this object is set to enabled, the NSSA Border router's ospfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating NSSA-LSA's into AS-External-LSA's. When this object is set to disabled, a candidate NSSA Border router is NOT translating NSSA-LSA's into AS-External-LSA's.
OBJECT-TYPE    
  INTEGER enabled(1), elected(2), disabled(3)  

jnxOspfv3AreaNssaTranslatorStabInt 1.3.6.1.4.1.2636.5.4.1.1.2.1.13
The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3AreaNssaTranslatorEvents 1.3.6.1.4.1.2636.5.4.1.1.2.1.14
Indicates the number of Translator State changes that have occurred since the last boot-up.
OBJECT-TYPE    
  Counter32  

jnxOspfv3AreaStubMetricType 1.3.6.1.4.1.2636.5.4.1.1.2.1.15
This variable displays the type of metric advertised as a default route.
OBJECT-TYPE    
  INTEGER ospfv3Metric(1), comparableCost(2), nonComparable(3)  

jnxOspfv3AsLsdbTable 1.3.6.1.4.1.2636.5.4.1.1.3
The OSPFv3 Process's AS-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3AsLsdbEntry

jnxOspfv3AsLsdbEntry 1.3.6.1.4.1.2636.5.4.1.1.3.1
A single AS-Scope Link State Advertisement.
OBJECT-TYPE    
  JnxOspfv3AsLsdbEntry  

jnxOspfv3AsLsdbType 1.3.6.1.4.1.2636.5.4.1.1.3.1.1
The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

jnxOspfv3AsLsdbRouterId 1.3.6.1.4.1.2636.5.4.1.1.3.1.2
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3AsLsdbLsid 1.3.6.1.4.1.2636.5.4.1.1.3.1.3
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3AsLsdbSequence 1.3.6.1.4.1.2636.5.4.1.1.3.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AsLsdbAge 1.3.6.1.4.1.2636.5.4.1.1.3.1.5
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AsLsdbChecksum 1.3.6.1.4.1.2636.5.4.1.1.3.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AsLsdbAdvertisement 1.3.6.1.4.1.2636.5.4.1.1.3.1.7
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

jnxOspfv3AsLsdbTypeKnown 1.3.6.1.4.1.2636.5.4.1.1.3.1.8
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3AreaLsdbTable 1.3.6.1.4.1.2636.5.4.1.1.4
The OSPFv3 Process's Area-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3AreaLsdbEntry

jnxOspfv3AreaLsdbEntry 1.3.6.1.4.1.2636.5.4.1.1.4.1
A single Area-Scope Link State Advertisement.
OBJECT-TYPE    
  JnxOspfv3AreaLsdbEntry  

jnxOspfv3AreaLsdbAreaId 1.3.6.1.4.1.2636.5.4.1.1.4.1.1
The 32-bit identifier of the Area from which the LSA was received.
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3AreaLsdbType 1.3.6.1.4.1.2636.5.4.1.1.4.1.2
The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

jnxOspfv3AreaLsdbRouterId 1.3.6.1.4.1.2636.5.4.1.1.4.1.3
The 32-bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3AreaLsdbLsid 1.3.6.1.4.1.2636.5.4.1.1.4.1.4
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3AreaLsdbSequence 1.3.6.1.4.1.2636.5.4.1.1.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AreaLsdbAge 1.3.6.1.4.1.2636.5.4.1.1.4.1.6
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AreaLsdbChecksum 1.3.6.1.4.1.2636.5.4.1.1.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

jnxOspfv3AreaLsdbAdvertisement 1.3.6.1.4.1.2636.5.4.1.1.4.1.8
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

jnxOspfv3AreaLsdbTypeKnown 1.3.6.1.4.1.2636.5.4.1.1.4.1.9
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3LinkLsdbTable 1.3.6.1.4.1.2636.5.4.1.1.5
The OSPFv3 Process's Link-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3LinkLsdbEntry

jnxOspfv3LinkLsdbEntry 1.3.6.1.4.1.2636.5.4.1.1.5.1
A single Link-Scope Link State Advertisement.
OBJECT-TYPE    
  JnxOspfv3LinkLsdbEntry  

jnxOspfv3LinkLsdbIfIndex 1.3.6.1.4.1.2636.5.4.1.1.5.1.1
The identifier of the link from which the LSA was received.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3LinkLsdbIfInstId 1.3.6.1.4.1.2636.5.4.1.1.5.1.2
The identifier of the interface instance from which the LSA was received.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3LinkLsdbType 1.3.6.1.4.1.2636.5.4.1.1.5.1.3
The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

jnxOspfv3LinkLsdbRouterId 1.3.6.1.4.1.2636.5.4.1.1.5.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3LinkLsdbLsid 1.3.6.1.4.1.2636.5.4.1.1.5.1.5
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3LinkLsdbSequence 1.3.6.1.4.1.2636.5.4.1.1.5.1.6
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

jnxOspfv3LinkLsdbAge 1.3.6.1.4.1.2636.5.4.1.1.5.1.7
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

jnxOspfv3LinkLsdbChecksum 1.3.6.1.4.1.2636.5.4.1.1.5.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

jnxOspfv3LinkLsdbAdvertisement 1.3.6.1.4.1.2636.5.4.1.1.5.1.9
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

jnxOspfv3LinkLsdbTypeKnown 1.3.6.1.4.1.2636.5.4.1.1.5.1.10
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3HostTable 1.3.6.1.4.1.2636.5.4.1.1.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3HostEntry

jnxOspfv3HostEntry 1.3.6.1.4.1.2636.5.4.1.1.6.1
A metric to be advertised when a given host is reachable.
OBJECT-TYPE    
  JnxOspfv3HostEntry  

jnxOspfv3HostAddressType 1.3.6.1.4.1.2636.5.4.1.1.6.1.1
The address type of ospfv3HostAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

jnxOspfv3HostAddress 1.3.6.1.4.1.2636.5.4.1.1.6.1.2
The IPv6 Address of the Host. Must be a Global address.
OBJECT-TYPE    
  InetAddress SIZE(16)  

jnxOspfv3HostMetric 1.3.6.1.4.1.2636.5.4.1.1.6.1.3
The Metric to be advertised.
OBJECT-TYPE    
  Metric  

jnxOspfv3HostStatus 1.3.6.1.4.1.2636.5.4.1.1.6.1.4
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3HostAreaID 1.3.6.1.4.1.2636.5.4.1.1.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 interface is in, or Area 0
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3IfTable 1.3.6.1.4.1.2636.5.4.1.1.7
The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3IfEntry

jnxOspfv3IfEntry 1.3.6.1.4.1.2636.5.4.1.1.7.1
The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3.
OBJECT-TYPE    
  JnxOspfv3IfEntry  

jnxOspfv3IfIndex 1.3.6.1.4.1.2636.5.4.1.1.7.1.1
The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3IfInstId 1.3.6.1.4.1.2636.5.4.1.1.7.1.2
Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3IfAreaId 1.3.6.1.4.1.2636.5.4.1.1.7.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3IfType 1.3.6.1.4.1.2636.5.4.1.1.7.1.4
The OSPFv3 interface type.
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)  

jnxOspfv3IfAdminStat 1.3.6.1.4.1.2636.5.4.1.1.7.1.5
The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3.
OBJECT-TYPE    
  Status  

jnxOspfv3IfRtrPriority 1.3.6.1.4.1.2636.5.4.1.1.7.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
OBJECT-TYPE    
  DesignatedRouterPriority  

jnxOspfv3IfTransitDelay 1.3.6.1.4.1.2636.5.4.1.1.7.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3IfRetransInterval 1.3.6.1.4.1.2636.5.4.1.1.7.1.8
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3IfHelloInterval 1.3.6.1.4.1.2636.5.4.1.1.7.1.9
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  HelloRange  

jnxOspfv3IfRtrDeadInterval 1.3.6.1.4.1.2636.5.4.1.1.7.1.10
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  JnxOspfv3DeadIntRangeTc  

jnxOspfv3IfPollInterval 1.3.6.1.4.1.2636.5.4.1.1.7.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3IfState 1.3.6.1.4.1.2636.5.4.1.1.7.1.12
The OSPFv3 Interface State.
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)  

jnxOspfv3IfDesignatedRouter 1.3.6.1.4.1.2636.5.4.1.1.7.1.13
The Router ID of the Designated Router.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3IfBackupDesignatedRouter 1.3.6.1.4.1.2636.5.4.1.1.7.1.14
The Router ID of the Backup Designated Router.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3IfEvents 1.3.6.1.4.1.2636.5.4.1.1.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

jnxOspfv3IfStatus 1.3.6.1.4.1.2636.5.4.1.1.7.1.16
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3IfMulticastForwarding 1.3.6.1.4.1.2636.5.4.1.1.7.1.17
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effectively disables all multicast forwarding.
OBJECT-TYPE    
  INTEGER blocked(1), multicast(2), unicast(3)  

jnxOspfv3IfDemand 1.3.6.1.4.1.2636.5.4.1.1.7.1.18
Indicates whether Demand OSPFv3 procedures (hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3IfMetricValue 1.3.6.1.4.1.2636.5.4.1.1.7.1.19
The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the ospfv3ReferenceBandwidth object.
OBJECT-TYPE    
  Metric  

jnxOspfv3IfLinkScopeLsaCount 1.3.6.1.4.1.2636.5.4.1.1.7.1.20
The total number of Link-Scope link state advertisements in this link's link state database.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3IfLinkLsaCksumSum 1.3.6.1.4.1.2636.5.4.1.1.7.1.21
The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

jnxOspfv3IfDemandNbrProbe 1.3.6.1.4.1.2636.5.4.1.1.7.1.22
Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.
OBJECT-TYPE    
  TruthValue  

jnxOspfv3IfDemandNbrProbeRetxLimit 1.3.6.1.4.1.2636.5.4.1.1.7.1.23
The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3IfDemandNbrProbeInterval 1.3.6.1.4.1.2636.5.4.1.1.7.1.24
Defines how often the neighbor will be probed.
OBJECT-TYPE    
  Unsigned32  

jnxOspfv3VirtIfTable 1.3.6.1.4.1.2636.5.4.1.1.8
Information about this router's virtual interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3VirtIfEntry

jnxOspfv3VirtIfEntry 1.3.6.1.4.1.2636.5.4.1.1.8.1
Information about a single Virtual Interface.
OBJECT-TYPE    
  JnxOspfv3VirtIfEntry  

jnxOspfv3VirtIfAreaId 1.3.6.1.4.1.2636.5.4.1.1.8.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not Area 0
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3VirtIfNeighbor 1.3.6.1.4.1.2636.5.4.1.1.8.1.2
The Router ID of the Virtual Neighbor.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3VirtIfIndex 1.3.6.1.4.1.2636.5.4.1.1.8.1.3
The local interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3VirtIfInstId 1.3.6.1.4.1.2636.5.4.1.1.8.1.4
Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3VirtIfTransitDelay 1.3.6.1.4.1.2636.5.4.1.1.8.1.5
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3VirtIfRetransInterval 1.3.6.1.4.1.2636.5.4.1.1.8.1.6
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3VirtIfHelloInterval 1.3.6.1.4.1.2636.5.4.1.1.8.1.7
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  HelloRange  

jnxOspfv3VirtIfRtrDeadInterval 1.3.6.1.4.1.2636.5.4.1.1.8.1.8
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  JnxOspfv3DeadIntRangeTc  

jnxOspfv3VirtIfState 1.3.6.1.4.1.2636.5.4.1.1.8.1.9
ospf virtual interface states. The same encoding as the ospfV3IfTable is used.
OBJECT-TYPE    
  INTEGER down(1), pointToPoint(4)  

jnxOspfv3VirtIfEvents 1.3.6.1.4.1.2636.5.4.1.1.8.1.10
The number of state changes or error events on this Virtual Link
OBJECT-TYPE    
  Counter32  

jnxOspfv3VirtIfStatus 1.3.6.1.4.1.2636.5.4.1.1.8.1.11
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3VirtIfLinkScopeLsaCount 1.3.6.1.4.1.2636.5.4.1.1.8.1.12
The total number of Link-Scope link state advertisements in this virtual link's link state database.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3VirtIfLinkLsaCksumSum 1.3.6.1.4.1.2636.5.4.1.1.8.1.13
The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

jnxOspfv3NbrTable 1.3.6.1.4.1.2636.5.4.1.1.9
A table of non-virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3NbrEntry

jnxOspfv3NbrEntry 1.3.6.1.4.1.2636.5.4.1.1.9.1
The information regarding a single neighbor.
OBJECT-TYPE    
  JnxOspfv3NbrEntry  

jnxOspfv3NbrIfIndex 1.3.6.1.4.1.2636.5.4.1.1.9.1.1
The local link ID of the link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3NbrIfInstId 1.3.6.1.4.1.2636.5.4.1.1.9.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3NbrRtrId 1.3.6.1.4.1.2636.5.4.1.1.9.1.3
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3NbrAddressType 1.3.6.1.4.1.2636.5.4.1.1.9.1.4
The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

jnxOspfv3NbrAddress 1.3.6.1.4.1.2636.5.4.1.1.9.1.5
The IPv6 address of the neighbor associated with the local link.
OBJECT-TYPE    
  InetAddress SIZE(16)  

jnxOspfv3NbrOptions 1.3.6.1.4.1.2636.5.4.1.1.9.1.6
A Bit Mask corresponding to the neighbor's options field.
OBJECT-TYPE    
  Integer32  

jnxOspfv3NbrPriority 1.3.6.1.4.1.2636.5.4.1.1.9.1.7
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

jnxOspfv3NbrState 1.3.6.1.4.1.2636.5.4.1.1.9.1.8
The State of the relationship with this Neighbor.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

jnxOspfv3NbrEvents 1.3.6.1.4.1.2636.5.4.1.1.9.1.9
The number of times this neighbor relationship has changed state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

jnxOspfv3NbrLsRetransQLen 1.3.6.1.4.1.2636.5.4.1.1.9.1.10
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3NbrHelloSuppressed 1.3.6.1.4.1.2636.5.4.1.1.9.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

jnxOspfv3NbrIfId 1.3.6.1.4.1.2636.5.4.1.1.9.1.12
The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3NbrRestartHelperStatus 1.3.6.1.4.1.2636.5.4.1.1.9.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
OBJECT-TYPE    
  INTEGER notHelping(1), helping(2)  

jnxOspfv3NbrRestartHelperAge 1.3.6.1.4.1.2636.5.4.1.1.9.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3NbrRestartHelperExitRc 1.3.6.1.4.1.2636.5.4.1.1.9.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

jnxOspfv3CfgNbrTable 1.3.6.1.4.1.2636.5.4.1.1.10
A table of configured, non-virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3CfgNbrEntry

jnxOspfv3CfgNbrEntry 1.3.6.1.4.1.2636.5.4.1.1.10.1
The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery.
OBJECT-TYPE    
  JnxOspfv3CfgNbrEntry  

jnxOspfv3CfgNbrIfIndex 1.3.6.1.4.1.2636.5.4.1.1.10.1.1
The local link ID of the link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3CfgNbrIfInstId 1.3.6.1.4.1.2636.5.4.1.1.10.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3CfgNbrAddressType 1.3.6.1.4.1.2636.5.4.1.1.10.1.3
The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

jnxOspfv3CfgNbrAddress 1.3.6.1.4.1.2636.5.4.1.1.10.1.4
The IPv6 address of the neighbor associated with the local link.
OBJECT-TYPE    
  InetAddress SIZE(16)  

jnxOspfv3CfgNbrPriority 1.3.6.1.4.1.2636.5.4.1.1.10.1.5
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

jnxOspfv3CfgNbrStatus 1.3.6.1.4.1.2636.5.4.1.1.10.1.6
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3VirtNbrTable 1.3.6.1.4.1.2636.5.4.1.1.11
A table of virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3VirtNbrEntry

jnxOspfv3VirtNbrEntry 1.3.6.1.4.1.2636.5.4.1.1.11.1
Virtual neighbor information.
OBJECT-TYPE    
  JnxOspfv3VirtNbrEntry  

jnxOspfv3VirtNbrArea 1.3.6.1.4.1.2636.5.4.1.1.11.1.1
The Transit Area Identifier.
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3VirtNbrRtrId 1.3.6.1.4.1.2636.5.4.1.1.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  JnxOspfv3RouterIdTc  

jnxOspfv3VirtNbrIfIndex 1.3.6.1.4.1.2636.5.4.1.1.11.1.3
The local interface ID for the virtual link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3VirtNbrIfInstId 1.3.6.1.4.1.2636.5.4.1.1.11.1.4
The interface instance for the virtual link over which the neighbor can be reached.
OBJECT-TYPE    
  JnxOspfv3IfInstIdTc  

jnxOspfv3VirtNbrAddressType 1.3.6.1.4.1.2636.5.4.1.1.11.1.5
The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

jnxOspfv3VirtNbrAddress 1.3.6.1.4.1.2636.5.4.1.1.11.1.6
The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address.
OBJECT-TYPE    
  InetAddress SIZE(16)  

jnxOspfv3VirtNbrOptions 1.3.6.1.4.1.2636.5.4.1.1.11.1.7
A Bit Mask corresponding to the neighbor's options field.
OBJECT-TYPE    
  Integer32  

jnxOspfv3VirtNbrState 1.3.6.1.4.1.2636.5.4.1.1.11.1.8
The state of the Virtual Neighbor Relationship.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

jnxOspfv3VirtNbrEvents 1.3.6.1.4.1.2636.5.4.1.1.11.1.9
The number of times this virtual link has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

jnxOspfv3VirtNbrLsRetransQLen 1.3.6.1.4.1.2636.5.4.1.1.11.1.10
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

jnxOspfv3VirtNbrHelloSuppressed 1.3.6.1.4.1.2636.5.4.1.1.11.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

jnxOspfv3VirtNbrIfId 1.3.6.1.4.1.2636.5.4.1.1.11.1.12
The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID.
OBJECT-TYPE    
  InterfaceIndex  

jnxOspfv3VirtNbrRestartHelperStatus 1.3.6.1.4.1.2636.5.4.1.1.11.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
OBJECT-TYPE    
  INTEGER notHelping(1), helping(2)  

jnxOspfv3VirtNbrRestartHelperAge 1.3.6.1.4.1.2636.5.4.1.1.11.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
OBJECT-TYPE    
  JnxOspfv3UpToRefreshIntervalTc  

jnxOspfv3VirtNbrRestartHelperExitRc 1.3.6.1.4.1.2636.5.4.1.1.11.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

jnxOspfv3AreaAggregateTable 1.3.6.1.4.1.2636.5.4.1.1.12
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
OBJECT-TYPE    
  SEQUENCE OF  
    JnxOspfv3AreaAggregateEntry

jnxOspfv3AreaAggregateEntry 1.3.6.1.4.1.2636.5.4.1.1.12.1
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
OBJECT-TYPE    
  JnxOspfv3AreaAggregateEntry  

jnxOspfv3AreaAggregateAreaID 1.3.6.1.4.1.2636.5.4.1.1.12.1.1
The Area the Address Aggregate is to be found within.
OBJECT-TYPE    
  JnxOspfv3AreaIdTc  

jnxOspfv3AreaAggregateAreaLsdbType 1.3.6.1.4.1.2636.5.4.1.1.12.1.2
The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to.
OBJECT-TYPE    
  INTEGER interAreaPrefixLsa(8195), nssaExternalLsa(8199)  

jnxOspfv3AreaAggregatePrefixType 1.3.6.1.4.1.2636.5.4.1.1.12.1.4
The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected.
OBJECT-TYPE    
  InetAddressType  

jnxOspfv3AreaAggregatePrefix 1.3.6.1.4.1.2636.5.4.1.1.12.1.5
The IPv6 Prefix.
OBJECT-TYPE    
  InetAddress SIZE(0..16)  

jnxOspfv3AreaAggregatePrefixLength 1.3.6.1.4.1.2636.5.4.1.1.12.1.6
The length of the prefix (in bits). A prefix can not be shorter than 3 bits.
OBJECT-TYPE    
  InetAddressPrefixLength 3..128  

jnxOspfv3AreaAggregateStatus 1.3.6.1.4.1.2636.5.4.1.1.12.1.7
This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
OBJECT-TYPE    
  RowStatus  

jnxOspfv3AreaAggregateEffect 1.3.6.1.4.1.2636.5.4.1.1.12.1.8
Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area.
OBJECT-TYPE    
  INTEGER advertiseMatching(1), doNotAdvertiseMatching(2)  

jnxOspfv3AreaAggregateRouteTag 1.3.6.1.4.1.2636.5.4.1.1.12.1.9
This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSA's to AS-External-LSA's.
OBJECT-TYPE    
  INTEGER  

jnxOspfv3NotificationEntry 1.3.6.1.4.1.2636.5.4.1.1.13
OBJECT IDENTIFIER    

jnxOspfv3ConfigErrorType 1.3.6.1.4.1.2636.5.4.1.1.13.1
Potential types of configuration conflicts. Used by the ospfv3ConfigError and ospfv3ConfigVirtError notifications. When the last value of a notification using this object is needed, but no notifications of that type have been sent, this value pertaining to this object should be returned as noError
OBJECT-TYPE    
  INTEGER badVersion(1), areaMismatch(2), unknownNbmaNbr(3), unknownVirtualNbr(4), helloIntervalMismatch(5), deadIntervalMismatch(6), optionMismatch(7), mtuMismatch(8), duplicateRouterId(9), noError(10)  

jnxOspfv3PacketType 1.3.6.1.4.1.2636.5.4.1.1.13.2
OSPFv3 packet types. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as nullPacket
OBJECT-TYPE    
  INTEGER hello(1), dbDescript(2), lsReq(3), lsUpdate(4), lsAck(5), nullPacket(6)  

jnxOspfv3PacketSrc 1.3.6.1.4.1.2636.5.4.1.1.13.3
The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as 0 Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddress  

jnxOspfv3Conformance 1.3.6.1.4.1.2636.5.4.1.2
OBJECT IDENTIFIER    

jnxOspfv3Groups 1.3.6.1.4.1.2636.5.4.1.2.1
OBJECT IDENTIFIER    

jnxOspfv3BasicGroup 1.3.6.1.4.1.2636.5.4.1.2.1.1
These objects are used for managing/monitoring OSPFv3 global parameters.
OBJECT-GROUP    

jnxOspfv3AreaGroup 1.3.6.1.4.1.2636.5.4.1.2.1.2
These objects are used for ospfv3 systems supporting areas.
OBJECT-GROUP    

jnxOspfv3AsLsdbGroup 1.3.6.1.4.1.2636.5.4.1.2.1.3
These objects are used for ospfv3 systems that display their AS-scope link state database.
OBJECT-GROUP    

jnxOspfv3AreaLsdbGroup 1.3.6.1.4.1.2636.5.4.1.2.1.4
These objects are used for OSPFv3 systems that display their Area-scope link state database.
OBJECT-GROUP    

jnxOspfv3LinkLsdbGroup 1.3.6.1.4.1.2636.5.4.1.2.1.5
These objects are used for OSPFv3 systems that display their Link-scope link state database.
OBJECT-GROUP    

jnxOspfv3HostGroup 1.3.6.1.4.1.2636.5.4.1.2.1.6
These objects are used for OSPFv3 systems that support attached hosts.
OBJECT-GROUP    

jnxOspfv3IfGroup 1.3.6.1.4.1.2636.5.4.1.2.1.7
These interface objects used for managing/monitoring OSPFv3 interfaces.
OBJECT-GROUP    

jnxOspfv3VirtIfGroup 1.3.6.1.4.1.2636.5.4.1.2.1.8
These virtual interface objects are used for managing/monitoring OSPFv3 virtual interfaces.
OBJECT-GROUP    

jnxOspfv3NbrGroup 1.3.6.1.4.1.2636.5.4.1.2.1.9
These neighbor objects are used for managing/monitoring OSPFv3 neighbors.
OBJECT-GROUP    

jnxOspfv3CfgNbrGroup 1.3.6.1.4.1.2636.5.4.1.2.1.10
These configured neighbor objects are used for managing/monitoring ospfv3 configured neighbors.
OBJECT-GROUP    

jnxOspfv3VirtNbrGroup 1.3.6.1.4.1.2636.5.4.1.2.1.11
These virtual neighbor objects are used for managing/monitoring OSPFv3 virtual neighbors.
OBJECT-GROUP    

jnxOspfv3AreaAggregateGroup 1.3.6.1.4.1.2636.5.4.1.2.1.12
These area aggregate objects used required for aggregating OSPFv3 prefixes for summarization across areas.
OBJECT-GROUP    

jnxOspfv3NotificationObjectGroup 1.3.6.1.4.1.2636.5.4.1.2.1.13
These objects are used to record notification parameters
OBJECT-GROUP    

jnxOspfv3NotificationGroup 1.3.6.1.4.1.2636.5.4.1.2.1.14
This group is used for OSPFv3 notifications
NOTIFICATION-GROUP    

jnxOspfv3Compliances 1.3.6.1.4.1.2636.5.4.1.2.2
OBJECT IDENTIFIER    

jnxOspfv3Compliance 1.3.6.1.4.1.2636.5.4.1.2.2.1
The compliance statement
MODULE-COMPLIANCE    

Defined Objects

JnxOspfv3UpToRefreshIntervalTc  
The values one might be able to configure for variables bounded by the Refresh Interval
TEXTUAL-CONVENTION    
  Integer32 1..1800  

JnxOspfv3DeadIntRangeTc  
The range, in seconds, of dead interval value.
TEXTUAL-CONVENTION    
  Integer32 1..'FFFF'h  

JnxOspfv3RouterIdTc  
A 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

JnxOspfv3AreaIdTc  
An OSPFv3 Area Identifier
TEXTUAL-CONVENTION    
  Unsigned32 0..'FFFFFFFF'h  

JnxOspfv3IfInstIdTc  
An OSPFv3 interface instance ID
TEXTUAL-CONVENTION    
  Integer32 0..255  

JnxOspfv3AreaEntry  
SEQUENCE    
  JnxOspfv3AreaIdTc as jnxOspfv3AreaId  
  INTEGER as jnxOspfv3ImportAsExtern  
  Counter32 as jnxOspfv3AreaSpfRuns  
  Gauge32 as jnxOspfv3AreaBdrRtrCount  
  Gauge32 as jnxOspfv3AreaAsBdrRtrCount  
  Gauge32 as jnxOspfv3AreaScopeLsaCount  
  Integer32 as jnxOspfv3AreaScopeLsaCksumSum  
  INTEGER as jnxOspfv3AreaSummary  
  RowStatus as jnxOspfv3AreaStatus  
  BigMetric as jnxOspfv3StubMetric  
  INTEGER as jnxOspfv3AreaNssaTranslatorRole  
  INTEGER as jnxOspfv3AreaNssaTranslatorState  
  Unsigned32 as jnxOspfv3AreaNssaTranslatorStabInt  
  Counter32 as jnxOspfv3AreaNssaTranslatorEvents  
  INTEGER as jnxOspfv3AreaStubMetricType  

JnxOspfv3AsLsdbEntry  
SEQUENCE    
  Unsigned32 as jnxOspfv3AsLsdbType  
  JnxOspfv3RouterIdTc as jnxOspfv3AsLsdbRouterId  
  Unsigned32 as jnxOspfv3AsLsdbLsid  
  Integer32 as jnxOspfv3AsLsdbSequence  
  Integer32 as jnxOspfv3AsLsdbAge  
  Integer32 as jnxOspfv3AsLsdbChecksum  
  OCTET STRING as jnxOspfv3AsLsdbAdvertisement  
  TruthValue as jnxOspfv3AsLsdbTypeKnown  

JnxOspfv3AreaLsdbEntry  
SEQUENCE    
  JnxOspfv3AreaIdTc as jnxOspfv3AreaLsdbAreaId  
  Unsigned32 as jnxOspfv3AreaLsdbType  
  JnxOspfv3RouterIdTc as jnxOspfv3AreaLsdbRouterId  
  Unsigned32 as jnxOspfv3AreaLsdbLsid  
  Integer32 as jnxOspfv3AreaLsdbSequence  
  Integer32 as jnxOspfv3AreaLsdbAge  
  Integer32 as jnxOspfv3AreaLsdbChecksum  
  OCTET STRING as jnxOspfv3AreaLsdbAdvertisement  
  TruthValue as jnxOspfv3AreaLsdbTypeKnown  

JnxOspfv3LinkLsdbEntry  
SEQUENCE    
  InterfaceIndex as jnxOspfv3LinkLsdbIfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3LinkLsdbIfInstId  
  Unsigned32 as jnxOspfv3LinkLsdbType  
  JnxOspfv3RouterIdTc as jnxOspfv3LinkLsdbRouterId  
  Unsigned32 as jnxOspfv3LinkLsdbLsid  
  Integer32 as jnxOspfv3LinkLsdbSequence  
  Integer32 as jnxOspfv3LinkLsdbAge  
  Integer32 as jnxOspfv3LinkLsdbChecksum  
  OCTET STRING as jnxOspfv3LinkLsdbAdvertisement  
  TruthValue as jnxOspfv3LinkLsdbTypeKnown  

JnxOspfv3HostEntry  
SEQUENCE    
  InetAddressType as jnxOspfv3HostAddressType  
  InetAddress as jnxOspfv3HostAddress  
  Metric as jnxOspfv3HostMetric  
  RowStatus as jnxOspfv3HostStatus  
  JnxOspfv3AreaIdTc as jnxOspfv3HostAreaID  

JnxOspfv3IfEntry  
SEQUENCE    
  InterfaceIndex as jnxOspfv3IfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3IfInstId  
  JnxOspfv3AreaIdTc as jnxOspfv3IfAreaId  
  INTEGER as jnxOspfv3IfType  
  Status as jnxOspfv3IfAdminStat  
  DesignatedRouterPriority as jnxOspfv3IfRtrPriority  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3IfTransitDelay  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3IfRetransInterval  
  HelloRange as jnxOspfv3IfHelloInterval  
  JnxOspfv3DeadIntRangeTc as jnxOspfv3IfRtrDeadInterval  
  Unsigned32 as jnxOspfv3IfPollInterval  
  INTEGER as jnxOspfv3IfState  
  JnxOspfv3RouterIdTc as jnxOspfv3IfDesignatedRouter  
  JnxOspfv3RouterIdTc as jnxOspfv3IfBackupDesignatedRouter  
  Counter32 as jnxOspfv3IfEvents  
  RowStatus as jnxOspfv3IfStatus  
  INTEGER as jnxOspfv3IfMulticastForwarding  
  TruthValue as jnxOspfv3IfDemand  
  Metric as jnxOspfv3IfMetricValue  
  Gauge32 as jnxOspfv3IfLinkScopeLsaCount  
  Integer32 as jnxOspfv3IfLinkLsaCksumSum  
  TruthValue as jnxOspfv3IfDemandNbrProbe  
  Unsigned32 as jnxOspfv3IfDemandNbrProbeRetxLimit  
  Unsigned32 as jnxOspfv3IfDemandNbrProbeInterval  

JnxOspfv3VirtIfEntry  
SEQUENCE    
  JnxOspfv3AreaIdTc as jnxOspfv3VirtIfAreaId  
  JnxOspfv3RouterIdTc as jnxOspfv3VirtIfNeighbor  
  InterfaceIndex as jnxOspfv3VirtIfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3VirtIfInstId  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3VirtIfTransitDelay  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3VirtIfRetransInterval  
  HelloRange as jnxOspfv3VirtIfHelloInterval  
  JnxOspfv3DeadIntRangeTc as jnxOspfv3VirtIfRtrDeadInterval  
  INTEGER as jnxOspfv3VirtIfState  
  Counter32 as jnxOspfv3VirtIfEvents  
  RowStatus as jnxOspfv3VirtIfStatus  
  Gauge32 as jnxOspfv3VirtIfLinkScopeLsaCount  
  Integer32 as jnxOspfv3VirtIfLinkLsaCksumSum  

JnxOspfv3NbrEntry  
SEQUENCE    
  InterfaceIndex as jnxOspfv3NbrIfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3NbrIfInstId  
  JnxOspfv3RouterIdTc as jnxOspfv3NbrRtrId  
  InetAddressType as jnxOspfv3NbrAddressType  
  InetAddress as jnxOspfv3NbrAddress  
  Integer32 as jnxOspfv3NbrOptions  
  DesignatedRouterPriority as jnxOspfv3NbrPriority  
  INTEGER as jnxOspfv3NbrState  
  Counter32 as jnxOspfv3NbrEvents  
  Gauge32 as jnxOspfv3NbrLsRetransQLen  
  TruthValue as jnxOspfv3NbrHelloSuppressed  
  InterfaceIndex as jnxOspfv3NbrIfId  
  INTEGER as jnxOspfv3NbrRestartHelperStatus  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3NbrRestartHelperAge  
  INTEGER as jnxOspfv3NbrRestartHelperExitRc  

JnxOspfv3CfgNbrEntry  
SEQUENCE    
  InterfaceIndex as jnxOspfv3CfgNbrIfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3CfgNbrIfInstId  
  InetAddressType as jnxOspfv3CfgNbrAddressType  
  InetAddress as jnxOspfv3CfgNbrAddress  
  DesignatedRouterPriority as jnxOspfv3CfgNbrPriority  
  RowStatus as jnxOspfv3CfgNbrStatus  

JnxOspfv3VirtNbrEntry  
SEQUENCE    
  JnxOspfv3AreaIdTc as jnxOspfv3VirtNbrArea  
  JnxOspfv3RouterIdTc as jnxOspfv3VirtNbrRtrId  
  InterfaceIndex as jnxOspfv3VirtNbrIfIndex  
  JnxOspfv3IfInstIdTc as jnxOspfv3VirtNbrIfInstId  
  InetAddressType as jnxOspfv3VirtNbrAddressType  
  InetAddress as jnxOspfv3VirtNbrAddress  
  Integer32 as jnxOspfv3VirtNbrOptions  
  INTEGER as jnxOspfv3VirtNbrState  
  Counter32 as jnxOspfv3VirtNbrEvents  
  Gauge32 as jnxOspfv3VirtNbrLsRetransQLen  
  TruthValue as jnxOspfv3VirtNbrHelloSuppressed  
  InterfaceIndex as jnxOspfv3VirtNbrIfId  
  INTEGER as jnxOspfv3VirtNbrRestartHelperStatus  
  JnxOspfv3UpToRefreshIntervalTc as jnxOspfv3VirtNbrRestartHelperAge  
  INTEGER as jnxOspfv3VirtNbrRestartHelperExitRc  

JnxOspfv3AreaAggregateEntry  
SEQUENCE    
  JnxOspfv3AreaIdTc as jnxOspfv3AreaAggregateAreaID  
  INTEGER as jnxOspfv3AreaAggregateAreaLsdbType  
  InetAddressType as jnxOspfv3AreaAggregatePrefixType  
  InetAddress as jnxOspfv3AreaAggregatePrefix  
  InetAddressPrefixLength as jnxOspfv3AreaAggregatePrefixLength  
  RowStatus as jnxOspfv3AreaAggregateStatus  
  INTEGER as jnxOspfv3AreaAggregateEffect  
  INTEGER as jnxOspfv3AreaAggregateRouteTag