OSPFV3-MIB

File: OSPFV3-MIB.mib (117193 bytes)

Imported modules

ALCATEL-IND1-BASE SNMPv2-SMI SNMPv2-TC
SNMPv2-CONF IF-MIB INET-ADDRESS-MIB
OSPF-MIB

Imported symbols

routingIND1Ospf3 MODULE-IDENTITY OBJECT-TYPE
Counter32 Gauge32 Integer32
Unsigned32 TEXTUAL-CONVENTION TruthValue
StorageType RowStatus MODULE-COMPLIANCE
OBJECT-GROUP InterfaceIndex InetAddressType
InetAddress InetAddressPrefixLength Metric
BigMetric Status HelloRange
DesignatedRouterPriority

Defined Objects

ospfv3MIB 1.3.6.1.4.1.6486.800.1.2.1.10.13.999
The MIB module to describe OSPF version 3. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC XXXX; see the RFC itself for full legal notices.
MODULE-IDENTITY    

ospfv3Objects 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1
OBJECT IDENTIFIER    

ospfv3GeneralGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1
OBJECT IDENTIFIER    

ospfv3RouterId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.1
A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3AdminStat 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.2
The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces.
OBJECT-TYPE    
  Status  

ospfv3VersionNumber 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.3
The version number of OSPF for IPv6 is 3.
OBJECT-TYPE    
  INTEGER version3(3)  

ospfv3AreaBdrRtrStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.4
A flag to note whether this router is an area border router.
OBJECT-TYPE    
  TruthValue  

ospfv3ASBdrRtrStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.5
A flag to note whether this router is configured as an Autonomous System border router.
OBJECT-TYPE    
  TruthValue  

ospfv3AsScopeLsaCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.6
The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database.
OBJECT-TYPE    
  Gauge32  

ospfv3AsScopeLsaCksumSum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.7
The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfv3OriginateNewLsas 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.8
The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
OBJECT-TYPE    
  Counter32  

ospfv3RxNewLsas 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.9
The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements.
OBJECT-TYPE    
  Counter32  

ospfv3ExtLsaCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.10
The number of External(LS type 0x4005) in the link state database
OBJECT-TYPE    
  Gauge32  

ospfv3ExtAreaLsdbLimit 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.11
The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. OspfExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded).
OBJECT-TYPE    
  Integer32 -1..'7FFFFFFF'h  

ospfv3MulticastExtensions 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.12
A Bit Mask indicating whether the router is forwarding IPv6 multicast datagrams based on the algorithms defined in the Multicast Extensions to OSPF. If intraAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams in the router's directly attached areas (called intra-area multicast routing). If interAreaMulticast set, indicates that the router can forward IPv6 multicast datagrams between OSPFv3 areas (called inter-area multicast routing). If interAsMulticast set, indicates that the router can forward IPv6 multicast datagrams between Autonomous Systems (called inter-AS multicast routing). Only certain combinations of bit settings are allowed, namely: - All bits cleared (no multicasting) - intraAreaMulticast only, - intraAreaMulticast and interAreaMulticast, - intraAreaMulticast and interAsMulticast - intraAreaMulticast, interAreaMulticast and interAsMulticast By default, all bits are cleared.
OBJECT-TYPE    
  BITS intraAreaMulticast(0), interAreaMulticast(1), interAsMulticast(2)  

ospfv3ExitOverflowInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.13
The number of seconds that, after entering Overflow State, a router will attempt to leave Overflow State. This allows the router to again originate non-default, AS-External-LSAs. When set to 0, the router will not leave Overflow State until restarted.
OBJECT-TYPE    
  Unsigned32  

ospfv3DemandExtensions 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.14
The router's support for demand routing.
OBJECT-TYPE    
  TruthValue  

ospfv3ReferenceBandwidth 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.15
Reference bandwidth in kilobits/second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS)
OBJECT-TYPE    
  Unsigned32  

ospfv3RestartSupport 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.16
The router's support for OSPF Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts.
OBJECT-TYPE    
  INTEGER none(1), plannedOnly(2), plannedAndUnplanned(3)  

ospfv3RestartInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.17
Configured OSPF Graceful restart timeout interval.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3RestartStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.18
The current status of OSPF Graceful restart capability.
OBJECT-TYPE    
  INTEGER notRestarting(1), plannedRestart(2), unplannedRestart(3)  

ospfv3RestartAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.19
Remaining time in current OSPF Graceful restart interval.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3RestartExitRc 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.1.20
Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

ospfv3AreaTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2
Information describing the configured parameters and cumulative statistics of the router's attached areas.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3AreaEntry

ospfv3AreaEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1
Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
OBJECT-TYPE    
  Ospfv3AreaEntry  

ospfv3AreaId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.1
A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3ImportAsExtern 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.2
Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope
OBJECT-TYPE    
  INTEGER importExternal(1), importNoExternal(2), importNssa(3)  

ospfv3AreaSpfRuns 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.3
The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm.
OBJECT-TYPE    
  Counter32  

ospfv3AreaBdrRtrCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.4
The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

ospfv3AreaAsBdrRtrCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.5
The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
OBJECT-TYPE    
  Gauge32  

ospfv3AreaScopeLsaCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.6
The total number of Area-Scope link state advertisements in this area's link state database.
OBJECT-TYPE    
  Gauge32  

ospfv3AreaScopeLsaCksumSum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.7
The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfv3AreaSummary 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.8
The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs.
OBJECT-TYPE    
  INTEGER noAreaSummary(1), sendAreaSummary(2)  

ospfv3AreaStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.9
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3StubMetric 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.10
The metric value advertised for the default route into Stub and NSSA areas.
OBJECT-TYPE    
  BigMetric  

ospfv3AreaNssaTranslatorRole 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.11
Indicates an NSSA Border router's ability to perform NSSA translation of NSSA-LSAs into AS-External-LSAs.
OBJECT-TYPE    
  INTEGER always(1), candidate(2)  

ospfv3AreaNssaTranslatorState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.12
Indicates if and how an NSSA Border router is performing NSSA translation of NSSA-LSAs into AS-External-LSA�s. When this object is set to enabled, the NSSA Border router's ospfv3AreaNssTranslatorRole has been set to always. When this object is set to elected, a candidate NSSA Border router is translating NSSA-LSA�s into AS-External-LSA�s. When this object is set to disabled, a candidate NSSA Border router is NOT translating NSSA-LSA�s into AS-External-LSA�s.
OBJECT-TYPE    
  INTEGER enabled(1), elected(2), disabled(3)  

ospfv3AreaNssaTranslatorStabInt 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.13
The number of seconds after an elected translator determines its services are no longer required, that it should continue to perform its translation duties.
OBJECT-TYPE    
  Unsigned32  

ospfv3AreaNssaTranslatorEvents 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.14
Indicates the number of Translator State changes that have occurred since the last boot-up.
OBJECT-TYPE    
  Counter32  

ospfv3AreaStubMetricType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.2.1.15
This variable displays the type of metric advertised as a default route.
OBJECT-TYPE    
  INTEGER ospfv3Metric(1), comparableCost(2), nonComparable(3)  

ospfv3AsLsdbTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3
The OSPFv3 Process's AS-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3AsLsdbEntry

ospfv3AsLsdbEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1
A single AS-Scope Link State Advertisement.
OBJECT-TYPE    
  Ospfv3AsLsdbEntry  

ospfv3AsLsdbType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.1
The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

ospfv3AsLsdbRouterId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.2
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3AsLsdbLsid 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.3
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

ospfv3AsLsdbSequence 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.4
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

ospfv3AsLsdbAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.5
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

ospfv3AsLsdbChecksum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.6
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

ospfv3AsLsdbAdvertisement 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.7
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

ospfv3AsLsdbTypeKnown 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.3.1.8
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

ospfv3AreaLsdbTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4
The OSPFv3 Process's Area-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3AreaLsdbEntry

ospfv3AreaLsdbEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1
A single Area-Scope Link State Advertisement.
OBJECT-TYPE    
  Ospfv3AreaLsdbEntry  

ospfv3AreaLsdbAreaId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.1
The 32-bit identifier of the Area from which the LSA was received.
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3AreaLsdbType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.2
The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

ospfv3AreaLsdbRouterId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.3
The 32-bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3AreaLsdbLsid 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.4
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

ospfv3AreaLsdbSequence 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.5
The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

ospfv3AreaLsdbAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.6
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

ospfv3AreaLsdbChecksum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.7
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

ospfv3AreaLsdbAdvertisement 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.8
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

ospfv3AreaLsdbTypeKnown 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.4.1.9
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

ospfv3LinkLsdbTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5
The OSPFv3 Process's Link-Scope Link State Database.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3LinkLsdbEntry

ospfv3LinkLsdbEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1
A single Link-Scope Link State Advertisement.
OBJECT-TYPE    
  Ospfv3LinkLsdbEntry  

ospfv3LinkLsdbIfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.1
The identifier of the link from which the LSA was received.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3LinkLsdbIfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.2
The identifier of the interface instance from which the LSA was received.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3LinkLsdbType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.3
The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database.
OBJECT-TYPE    
  Unsigned32 0..'FFFFFFFF'h  

ospfv3LinkLsdbRouterId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.4
The 32 bit number that uniquely identifies the originating router in the Autonomous System.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3LinkLsdbLsid 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.5
The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
OBJECT-TYPE    
  Unsigned32  

ospfv3LinkLsdbSequence 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.6
The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
OBJECT-TYPE    
  Integer32  

ospfv3LinkLsdbAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.7
This field is the age of the link state advertisement in seconds.
OBJECT-TYPE    
  Integer32  

ospfv3LinkLsdbChecksum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.8
This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OBJECT-TYPE    
  Integer32  

ospfv3LinkLsdbAdvertisement 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.9
The entire Link State Advertisement, including its header.
OBJECT-TYPE    
  OCTET STRING SIZE(1..65535)  

ospfv3LinkLsdbTypeKnown 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.5.1.10
Indicates whether the LSA type is recognized by this Router.
OBJECT-TYPE    
  TruthValue  

ospfv3HostTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3HostEntry

ospfv3HostEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1
A metric to be advertised when a given host is reachable.
OBJECT-TYPE    
  Ospfv3HostEntry  

ospfv3HostAddressType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1.1
The address type of ospfv3HostAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

ospfv3HostAddress 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1.2
The IPv6 Address of the Host. Must be a Global address.
OBJECT-TYPE    
  InetAddress SIZE(16)  

ospfv3HostMetric 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1.3
The Metric to be advertised.
OBJECT-TYPE    
  Metric  

ospfv3HostStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1.4
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3HostAreaID 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPFv3 interface is in, or Area 0
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3IfTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7
The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3IfEntry

ospfv3IfEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1
The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3.
OBJECT-TYPE    
  Ospfv3IfEntry  

ospfv3IfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.1
The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3IfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.2
Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3IfAreaId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.3
A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3IfType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.4
The OSPFv3 interface type.
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointToPoint(3), pointToMultipoint(5)  

ospfv3IfAdminStat 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.5
The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3.
OBJECT-TYPE    
  Status  

ospfv3IfRtrPriority 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.6
The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
OBJECT-TYPE    
  DesignatedRouterPriority  

ospfv3IfTransitDelay 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.7
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3IfRetransInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.8
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3IfHelloInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.9
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  HelloRange  

ospfv3IfRtrDeadInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.10
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
OBJECT-TYPE    
  Ospfv3DeadIntRangeTc  

ospfv3IfPollInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.11
The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor.
OBJECT-TYPE    
  Unsigned32  

ospfv3IfState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.12
The OSPFv3 Interface State.
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointToPoint(4), designatedRouter(5), backupDesignatedRouter(6), otherDesignatedRouter(7)  

ospfv3IfDesignatedRouter 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.13
The Router ID of the Designated Router.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3IfBackupDesignatedRouter 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.14
The Router ID of the Backup Designated Router.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3IfEvents 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.15
The number of times this OSPF interface has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfv3IfStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.16
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3IfMulticastForwarding 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.17
The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effectively disables all multicast forwarding.
OBJECT-TYPE    
  INTEGER blocked(1), multicast(2), unicast(3)  

ospfv3IfDemand 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.18
Indicates whether Demand OSPFv3 procedures (hello suppression to FULL neighbors and setting the DoNotAge flag on propagated LSAs) should be performed on this interface.
OBJECT-TYPE    
  TruthValue  

ospfv3IfMetricValue 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.19
The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the ospfv3ReferenceBandwidth object.
OBJECT-TYPE    
  Metric  

ospfv3IfLinkScopeLsaCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.20
The total number of Link-Scope link state advertisements in this link's link state database.
OBJECT-TYPE    
  Gauge32  

ospfv3IfLinkLsaCksumSum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.21
The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfv3IfDemandNbrProbe 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.22
Indicates whether or not neighbor probing is enabled to determine whether or not the neighbor is inactive. Neighbor probing is disabled by default.
OBJECT-TYPE    
  TruthValue  

ospfv3IfDemandNbrProbeRetxLimit 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.23
The number of consecutive LSA retransmissions before the neighbor is deemed inactive and the neighbor adjacency is brought down.
OBJECT-TYPE    
  Unsigned32  

ospfv3IfDemandNbrProbeInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.7.1.24
Defines how often the neighbor will be probed.
OBJECT-TYPE    
  Unsigned32  

ospfv3VirtIfTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8
Information about this router's virtual interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3VirtIfEntry

ospfv3VirtIfEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1
Information about a single Virtual Interface.
OBJECT-TYPE    
  Ospfv3VirtIfEntry  

ospfv3VirtIfAreaId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.1
The Transit Area that the Virtual Link traverses. By definition, this is not Area 0
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3VirtIfNeighbor 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.2
The Router ID of the Virtual Neighbor.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3VirtIfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.3
The interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtal link and in the router's router-LSAs.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3VirtIfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.4
Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3VirtIfTransitDelay 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.5
The estimated number of seconds it takes to transmit a link state update packet over this interface.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3VirtIfRetransInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.6
The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3VirtIfHelloInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.7
The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  HelloRange  

ospfv3VirtIfRtrDeadInterval 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.8
The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
OBJECT-TYPE    
  Ospfv3DeadIntRangeTc  

ospfv3VirtIfState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.9
OSPF virtual interface states. The same encoding as the ospfV3IfTable is used.
OBJECT-TYPE    
  INTEGER down(1), pointToPoint(4)  

ospfv3VirtIfEvents 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.10
The number of state changes or error events on this Virtual Link
OBJECT-TYPE    
  Counter32  

ospfv3VirtIfStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.11
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3VirtIfLinkScopeLsaCount 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.12
The total number of Link-Scope link state advertisements in this virtual link's link state database.
OBJECT-TYPE    
  Gauge32  

ospfv3VirtIfLinkLsaCksumSum 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.8.1.13
The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
OBJECT-TYPE    
  Integer32  

ospfv3NbrTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9
A table of non-virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3NbrEntry

ospfv3NbrEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1
The information regarding a single neighbor.
OBJECT-TYPE    
  Ospfv3NbrEntry  

ospfv3NbrIfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.1
The local link ID of the link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3NbrIfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3NbrRtrId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.3
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3NbrAddressType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.4
The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

ospfv3NbrAddress 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.5
The IPv6 address of the neighbor associated with the local link.
OBJECT-TYPE    
  InetAddress SIZE(16)  

ospfv3NbrOptions 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.6
A Bit Mask corresponding to the neighbor's options field.
OBJECT-TYPE    
  Integer32  

ospfv3NbrPriority 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.7
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

ospfv3NbrState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.8
The State of the relationship with this Neighbor.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

ospfv3NbrEvents 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.9
The number of times this neighbor relationship has changed state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfv3NbrLsRetransQLen 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.10
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

ospfv3NbrHelloSuppressed 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

ospfv3NbrIfId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.12
The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3NbrRestartHelperStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
OBJECT-TYPE    
  INTEGER notHelping(1), helping(2)  

ospfv3NbrRestartHelperAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3NbrRestartHelperExitRc 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.9.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

ospfv3CfgNbrTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10
A table of configured non-virtual neighbor information and neighbors dynamically discovered by lower-level protocols such as Inverse Neighbor Discovery.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3CfgNbrEntry

ospfv3CfgNbrEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1
The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery.
OBJECT-TYPE    
  Ospfv3CfgNbrEntry  

ospfv3CfgNbrIfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.1
The local link ID of the link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3CfgNbrIfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.2
Interface instance over which the neighbor can be reached. This ID has local link significance only.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3CfgNbrAddressType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.3
The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

ospfv3CfgNbrAddress 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.4
The IPv6 address of the neighbor associated with the local link.
OBJECT-TYPE    
  InetAddress SIZE(16)  

ospfv3CfgNbrPriority 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.5
The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
OBJECT-TYPE    
  DesignatedRouterPriority  

ospfv3CfgNbrRtrId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.6
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System. A value of 0 is returned until a Hello is received from the configured neighbor.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3CfgNbrState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.7
The State of the relationship with this Neighbor.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

ospfv3CfgNbrStorageType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.8
The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. Manually configured entries will have a storage type of nonVolatile while entries dynamically created as a result of a lower-level protocol such as Inverse Neighbor Discovery will have a storage type of volatile.
OBJECT-TYPE    
  StorageType  

ospfv3CfgNbrStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.10.1.9
This variable controls the status of the entry. The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3VirtNbrTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11
A table of virtual neighbor information.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3VirtNbrEntry

ospfv3VirtNbrEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1
Virtual neighbor information.
OBJECT-TYPE    
  Ospfv3VirtNbrEntry  

ospfv3VirtNbrArea 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.1
The Transit Area Identifier.
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3VirtNbrRtrId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.2
A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
OBJECT-TYPE    
  Ospfv3RouterIdTc  

ospfv3VirtNbrIfIndex 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.3
The local interface ID for the virtual link over which the neighbor can be reached.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3VirtNbrIfInstId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.4
The interface instance for the virtual link over which the neighbor can be reached.
OBJECT-TYPE    
  Ospfv3IfInstIdTc  

ospfv3VirtNbrAddressType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.5
The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
OBJECT-TYPE    
  InetAddressType  

ospfv3VirtNbrAddress 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.6
The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address.
OBJECT-TYPE    
  InetAddress SIZE(16)  

ospfv3VirtNbrOptions 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.7
A Bit Mask corresponding to the neighbor's options field.
OBJECT-TYPE    
  Integer32  

ospfv3VirtNbrState 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.8
The state of the Virtual Neighbor Relationship.
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoWay(4), exchangeStart(5), exchange(6), loading(7), full(8)  

ospfv3VirtNbrEvents 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.9
The number of times this virtual link has changed its state, or an error has occurred.
OBJECT-TYPE    
  Counter32  

ospfv3VirtNbrLsRetransQLen 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.10
The current length of the retransmission queue.
OBJECT-TYPE    
  Gauge32  

ospfv3VirtNbrHelloSuppressed 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.11
Indicates whether Hellos are being suppressed to the neighbor
OBJECT-TYPE    
  TruthValue  

ospfv3VirtNbrIfId 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.12
The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID.
OBJECT-TYPE    
  InterfaceIndex  

ospfv3VirtNbrRestartHelperStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.13
Indicates whether the router is acting as a Graceful restart helper for the neighbor.
OBJECT-TYPE    
  INTEGER notHelping(1), helping(2)  

ospfv3VirtNbrRestartHelperAge 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.14
Remaining time in current OSPF Graceful restart interval, if the router is acting as a restart helper for the neighbor.
OBJECT-TYPE    
  Ospfv3UpToRefreshIntervalTc  

ospfv3VirtNbrRestartHelperExitRc 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.11.1.15
Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
OBJECT-TYPE    
  INTEGER none(1), inProgress(2), completed(3), timedOut(4), topologyChanged(5)  

ospfv3AreaAggregateTable 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
OBJECT-TYPE    
  SEQUENCE OF  
    Ospfv3AreaAggregateEntry

ospfv3AreaAggregateEntry 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1
A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
OBJECT-TYPE    
  Ospfv3AreaAggregateEntry  

ospfv3AreaAggregateAreaID 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.1
The Area the Address Aggregate is to be found within.
OBJECT-TYPE    
  Ospfv3AreaIdTc  

ospfv3AreaAggregateAreaLsdbType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.2
The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to.
OBJECT-TYPE    
  INTEGER interAreaPrefixLsa(8195), nssaExternalLsa(8199)  

ospfv3AreaAggregatePrefixType 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.4
The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected.
OBJECT-TYPE    
  InetAddressType  

ospfv3AreaAggregatePrefix 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.5
The IPv6 Prefix.
OBJECT-TYPE    
  InetAddress SIZE(0..16)  

ospfv3AreaAggregatePrefixLength 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.6
The length of the prefix (in bits). A prefix can not be shorter than 3 bits.
OBJECT-TYPE    
  InetAddressPrefixLength 3..128  

ospfv3AreaAggregateStatus 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.7
This variable controls the status of the entry The use of RowStatus is covered in more detail in [6].
OBJECT-TYPE    
  RowStatus  

ospfv3AreaAggregateEffect 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.8
Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area.
OBJECT-TYPE    
  INTEGER advertiseMatching(1), doNotAdvertiseMatching(2)  

ospfv3AreaAggregateRouteTag 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.1.12.1.9
This tag is advertised only in the summarized As-External LSA when summarizing from NSSA-LSA�s to AS-External-LSA�s.
OBJECT-TYPE    
  Integer32  

ospfv3Conformance 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2
OBJECT IDENTIFIER    

ospfv3Groups 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1
OBJECT IDENTIFIER    

ospfv3BasicGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.1
These objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3AreaGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.2
These objects are required for OSPFv3 systems supporting areas.
OBJECT-GROUP    

ospfv3AsLsdbGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.3
These objects are required for OSPFv3 systems that display their AS-scope link state database.
OBJECT-GROUP    

ospfv3AreaLsdbGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.4
These objects are required for OSPFv3 systems that display their Area-scope link state database.
OBJECT-GROUP    

ospfv3LinkLsdbGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.5
These objects are required for OSPFv3 systems that display their Link-scope link state database.
OBJECT-GROUP    

ospfv3HostGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.6
These objects are required for OSPFv3 systems that support attached hosts.
OBJECT-GROUP    

ospfv3IfGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.7
These interface objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3VirtIfGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.8
These virtual interface objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3NbrGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.9
These neighbor objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3CfgNbrGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.10
These Configured neighbor objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3VirtNbrGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.11
These virtual neighbor objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3AreaAggregateGroup 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.1.12
These area aggregate objects are required for OSPFv3 systems.
OBJECT-GROUP    

ospfv3Compliances 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.2
OBJECT IDENTIFIER    

ospfv3Compliance 1.3.6.1.4.1.6486.800.1.2.1.10.13.999.2.2.1
The compliance statement
MODULE-COMPLIANCE    

Defined Objects

Ospfv3UpToRefreshIntervalTc  
The values one might be able to configure for variables bounded by the Refresh Interval
TEXTUAL-CONVENTION    
  Integer32 1..1800  

Ospfv3DeadIntRangeTc  
The range, in seconds, of dead interval value.
TEXTUAL-CONVENTION    
  Integer32 1..'FFFF'h  

Ospfv3RouterIdTc  
A 32-bit, unsigned integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses if IPv4 is configured on the router.
TEXTUAL-CONVENTION    
  Unsigned32 0..'FFFFFFFF'h  

Ospfv3AreaIdTc  
An OSPFv3 Area Identifier
TEXTUAL-CONVENTION    
  Unsigned32 0..'FFFFFFFF'h  

Ospfv3IfInstIdTc  
An OSPFv3 interface instance ID
TEXTUAL-CONVENTION    
  Integer32 0..255  

Ospfv3AreaEntry  
SEQUENCE    
  Ospfv3AreaIdTc as ospfv3AreaId  
  INTEGER as ospfv3ImportAsExtern  
  Counter32 as ospfv3AreaSpfRuns  
  Gauge32 as ospfv3AreaBdrRtrCount  
  Gauge32 as ospfv3AreaAsBdrRtrCount  
  Gauge32 as ospfv3AreaScopeLsaCount  
  Integer32 as ospfv3AreaScopeLsaCksumSum  
  INTEGER as ospfv3AreaSummary  
  RowStatus as ospfv3AreaStatus  
  BigMetric as ospfv3StubMetric  
  INTEGER as ospfv3AreaNssaTranslatorRole  
  INTEGER as ospfv3AreaNssaTranslatorState  
  Unsigned32 as ospfv3AreaNssaTranslatorStabInt  
  Counter32 as ospfv3AreaNssaTranslatorEvents  
  INTEGER as ospfv3AreaStubMetricType  

Ospfv3AsLsdbEntry  
SEQUENCE    
  Unsigned32 as ospfv3AsLsdbType  
  Ospfv3RouterIdTc as ospfv3AsLsdbRouterId  
  Unsigned32 as ospfv3AsLsdbLsid  
  Integer32 as ospfv3AsLsdbSequence  
  Integer32 as ospfv3AsLsdbAge  
  Integer32 as ospfv3AsLsdbChecksum  
  OCTET STRING as ospfv3AsLsdbAdvertisement  
  TruthValue as ospfv3AsLsdbTypeKnown  

Ospfv3AreaLsdbEntry  
SEQUENCE    
  Ospfv3AreaIdTc as ospfv3AreaLsdbAreaId  
  Unsigned32 as ospfv3AreaLsdbType  
  Ospfv3RouterIdTc as ospfv3AreaLsdbRouterId  
  Unsigned32 as ospfv3AreaLsdbLsid  
  Integer32 as ospfv3AreaLsdbSequence  
  Integer32 as ospfv3AreaLsdbAge  
  Integer32 as ospfv3AreaLsdbChecksum  
  OCTET STRING as ospfv3AreaLsdbAdvertisement  
  TruthValue as ospfv3AreaLsdbTypeKnown  

Ospfv3LinkLsdbEntry  
SEQUENCE    
  InterfaceIndex as ospfv3LinkLsdbIfIndex  
  Ospfv3IfInstIdTc as ospfv3LinkLsdbIfInstId  
  Unsigned32 as ospfv3LinkLsdbType  
  Ospfv3RouterIdTc as ospfv3LinkLsdbRouterId  
  Unsigned32 as ospfv3LinkLsdbLsid  
  Integer32 as ospfv3LinkLsdbSequence  
  Integer32 as ospfv3LinkLsdbAge  
  Integer32 as ospfv3LinkLsdbChecksum  
  OCTET STRING as ospfv3LinkLsdbAdvertisement  
  TruthValue as ospfv3LinkLsdbTypeKnown  

Ospfv3HostEntry  
SEQUENCE    
  InetAddressType as ospfv3HostAddressType  
  InetAddress as ospfv3HostAddress  
  Metric as ospfv3HostMetric  
  RowStatus as ospfv3HostStatus  
  Ospfv3AreaIdTc as ospfv3HostAreaID  

Ospfv3IfEntry  
SEQUENCE    
  InterfaceIndex as ospfv3IfIndex  
  Ospfv3IfInstIdTc as ospfv3IfInstId  
  Ospfv3AreaIdTc as ospfv3IfAreaId  
  INTEGER as ospfv3IfType  
  Status as ospfv3IfAdminStat  
  DesignatedRouterPriority as ospfv3IfRtrPriority  
  Ospfv3UpToRefreshIntervalTc as ospfv3IfTransitDelay  
  Ospfv3UpToRefreshIntervalTc as ospfv3IfRetransInterval  
  HelloRange as ospfv3IfHelloInterval  
  Ospfv3DeadIntRangeTc as ospfv3IfRtrDeadInterval  
  Unsigned32 as ospfv3IfPollInterval  
  INTEGER as ospfv3IfState  
  Ospfv3RouterIdTc as ospfv3IfDesignatedRouter  
  Ospfv3RouterIdTc as ospfv3IfBackupDesignatedRouter  
  Counter32 as ospfv3IfEvents  
  RowStatus as ospfv3IfStatus  
  INTEGER as ospfv3IfMulticastForwarding  
  TruthValue as ospfv3IfDemand  
  Metric as ospfv3IfMetricValue  
  Gauge32 as ospfv3IfLinkScopeLsaCount  
  Integer32 as ospfv3IfLinkLsaCksumSum  
  TruthValue as ospfv3IfDemandNbrProbe  
  Unsigned32 as ospfv3IfDemandNbrProbeRetxLimit  
  Unsigned32 as ospfv3IfDemandNbrProbeInterval  

Ospfv3VirtIfEntry  
SEQUENCE    
  Ospfv3AreaIdTc as ospfv3VirtIfAreaId  
  Ospfv3RouterIdTc as ospfv3VirtIfNeighbor  
  InterfaceIndex as ospfv3VirtIfIndex  
  Ospfv3IfInstIdTc as ospfv3VirtIfInstId  
  Ospfv3UpToRefreshIntervalTc as ospfv3VirtIfTransitDelay  
  Ospfv3UpToRefreshIntervalTc as ospfv3VirtIfRetransInterval  
  HelloRange as ospfv3VirtIfHelloInterval  
  Ospfv3DeadIntRangeTc as ospfv3VirtIfRtrDeadInterval  
  INTEGER as ospfv3VirtIfState  
  Counter32 as ospfv3VirtIfEvents  
  RowStatus as ospfv3VirtIfStatus  
  Gauge32 as ospfv3VirtIfLinkScopeLsaCount  
  Integer32 as ospfv3VirtIfLinkLsaCksumSum  

Ospfv3NbrEntry  
SEQUENCE    
  InterfaceIndex as ospfv3NbrIfIndex  
  Ospfv3IfInstIdTc as ospfv3NbrIfInstId  
  Ospfv3RouterIdTc as ospfv3NbrRtrId  
  InetAddressType as ospfv3NbrAddressType  
  InetAddress as ospfv3NbrAddress  
  Integer32 as ospfv3NbrOptions  
  DesignatedRouterPriority as ospfv3NbrPriority  
  INTEGER as ospfv3NbrState  
  Counter32 as ospfv3NbrEvents  
  Gauge32 as ospfv3NbrLsRetransQLen  
  TruthValue as ospfv3NbrHelloSuppressed  
  InterfaceIndex as ospfv3NbrIfId  
  INTEGER as ospfv3NbrRestartHelperStatus  
  Ospfv3UpToRefreshIntervalTc as ospfv3NbrRestartHelperAge  
  INTEGER as ospfv3NbrRestartHelperExitRc  

Ospfv3CfgNbrEntry  
SEQUENCE    
  InterfaceIndex as ospfv3CfgNbrIfIndex  
  Ospfv3IfInstIdTc as ospfv3CfgNbrIfInstId  
  InetAddressType as ospfv3CfgNbrAddressType  
  InetAddress as ospfv3CfgNbrAddress  
  DesignatedRouterPriority as ospfv3CfgNbrPriority  
  Ospfv3RouterIdTc as ospfv3CfgNbrRtrId  
  INTEGER as ospfv3CfgNbrState  
  StorageType as ospfv3CfgNbrStorageType  
  RowStatus as ospfv3CfgNbrStatus  

Ospfv3VirtNbrEntry  
SEQUENCE    
  Ospfv3AreaIdTc as ospfv3VirtNbrArea  
  Ospfv3RouterIdTc as ospfv3VirtNbrRtrId  
  InterfaceIndex as ospfv3VirtNbrIfIndex  
  Ospfv3IfInstIdTc as ospfv3VirtNbrIfInstId  
  InetAddressType as ospfv3VirtNbrAddressType  
  InetAddress as ospfv3VirtNbrAddress  
  Integer32 as ospfv3VirtNbrOptions  
  INTEGER as ospfv3VirtNbrState  
  Counter32 as ospfv3VirtNbrEvents  
  Gauge32 as ospfv3VirtNbrLsRetransQLen  
  TruthValue as ospfv3VirtNbrHelloSuppressed  
  InterfaceIndex as ospfv3VirtNbrIfId  
  INTEGER as ospfv3VirtNbrRestartHelperStatus  
  Ospfv3UpToRefreshIntervalTc as ospfv3VirtNbrRestartHelperAge  
  INTEGER as ospfv3VirtNbrRestartHelperExitRc  

Ospfv3AreaAggregateEntry  
SEQUENCE    
  Ospfv3AreaIdTc as ospfv3AreaAggregateAreaID  
  INTEGER as ospfv3AreaAggregateAreaLsdbType  
  InetAddressType as ospfv3AreaAggregatePrefixType  
  InetAddress as ospfv3AreaAggregatePrefix  
  InetAddressPrefixLength as ospfv3AreaAggregatePrefixLength  
  RowStatus as ospfv3AreaAggregateStatus  
  INTEGER as ospfv3AreaAggregateEffect  
  Integer32 as ospfv3AreaAggregateRouteTag