PANDATEL-ETC-MODEM-MIB

File: PANDATEL-ETC-MODEM-MIB.mib (9512 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
PANDATEL-MODEM-MIB

Imported symbols

enterprises DisplayString OBJECT-TYPE
mdmSpecifics device-id

Defined Objects

etc 1.3.6.1.4.1.760.1.1.2.1.10.901
OBJECT IDENTIFIER    

etcModemTable 1.3.6.1.4.1.760.1.1.2.1.10.901.1
The table of all ETC modems in this housing.
OBJECT-TYPE    
  SEQUENCE OF  
    EtcTableEntry

etcTableEntry 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1
The index of the table.
OBJECT-TYPE    
  EtcTableEntry  

mdmRack 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.1
The index of the rack where the modem is installed.
OBJECT-TYPE    
  INTEGER  

mdmModem 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.2
This variable displays the slot number where the corresponding modem is installed in the rack.
OBJECT-TYPE    
  INTEGER  

mdmPosition 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.3
This variable displays the location of the corresponding modem: 'local' or 'remote'. The modem which is plugged into a managed rack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

mdmModemName 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.5
A verbal name of this modem.
OBJECT-TYPE    
  DisplayString  

mdmDataEquipmentEmulation 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.6
Interface mode of the unit: 'dte' or 'dce', 'te' or 'nt'.
OBJECT-TYPE    
  INTEGER other(1), to-hub(8), to-nic(9), unknown(99)  

mdmModemProperty 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.7
The speed class of the unit: 'eth100base-tx-full-duplex' or 'eth100base-tx-half-duplex'.
OBJECT-TYPE    
  INTEGER other(1), eth100base-tx-full-duplex(16), eth100base-tx-half-duplex(17), unknown(99)  

mdmAlarm 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.15
The status of local alarm: 'off' or 'on'.
OBJECT-TYPE    
  INTEGER other(1), off(2), on(3)  

mdmRemoteAccessMode 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.64
The possibility of remote management: 'enabled', 'disabled local' or 'disable local and remote'. Once disabled management at local and remote unit, it is not possible to enable it at the remote unit again.
OBJECT-TYPE    
  INTEGER other(1), enable(5), disable-local(8), disable-local-and-remote(9)  

mdmForcedRemoteAccess 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.65
Activation of remote management: 'on' or 'off'. Status 'on' enables management of remote unit. During this process the link is restricted to management data. The transmission of user data is interrupted. Status 'off' disables management of remote unit. The link transmits user data.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

mdmOperationMode 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.66
The possibility of operation mode: 'normal', 'remote-fault-detection mode' or 'link-pass-through'.
OBJECT-TYPE    
  INTEGER other(1), normal(7), remote-fault-detection(8), link-pass-through(9)  

mdmFoPower 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.71
The status of transmitter power: 'low' or 'high'.
OBJECT-TYPE    
  INTEGER other(1), low(2), high(3)  

mdmAutoDetectModemProperty 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.74
The status of auto detect of modem property: 'off' or 'on'.
OBJECT-TYPE    
  INTEGER other(1), off(2), on(3)  

mdmInterfaceAlarmCondition 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.98
The alarm trigger mode at interface port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down.
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), not-available(100)  

mdmLineAlarmCondition 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.99
The alarm trigger mode at line port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), laser-fail(4), no-link-signal-or-laser-fail(5), not-available(100)  

mdmStatusInterfacePort 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.140
The status 'disable': port is not active. The status 'enable': port is active.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

mdmStatusLinePort 1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.141
The status 'disable': port is not active. The status 'enable': port is active.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

etc-modem 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.901
OBJECT IDENTIFIER    

Defined Objects

EtcTableEntry  
SEQUENCE    
  INTEGER as mdmRack  
  INTEGER as mdmModem  
  INTEGER as mdmPosition  
  DisplayString as mdmModemName  
  INTEGER as mdmDataEquipmentEmulation  
  INTEGER as mdmModemProperty  
  INTEGER as mdmAlarm  
  INTEGER as mdmRemoteAccessMode  
  INTEGER as mdmForcedRemoteAccess  
  INTEGER as mdmOperationMode  
  INTEGER as mdmFoPower  
  INTEGER as mdmAutoDetectModemProperty  
  INTEGER as mdmInterfaceAlarmCondition  
  INTEGER as mdmLineAlarmCondition  
  INTEGER as mdmStatusInterfacePort  
  INTEGER as mdmStatusLinePort