PANDATEL-FME-MODEM-MIB

File: PANDATEL-FME-MODEM-MIB.mib (11891 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
PANDATEL-MODEM-MIB

Imported symbols

enterprises DisplayString OBJECT-TYPE
mdmSpecifics device-id

Defined Objects

fme 1.3.6.1.4.1.760.1.1.2.1.10.601
OBJECT IDENTIFIER    

fmeModemTable 1.3.6.1.4.1.760.1.1.2.1.10.601.1
This table contains information about all FME units within all stacks.
OBJECT-TYPE    
  SEQUENCE OF  
    FmeTableEntry

fmeTableEntry 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1
The index of the table.
OBJECT-TYPE    
  FmeTableEntry  

mdmRack 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.1
The index of the stack the unit belongs to. The stack corresponds to a rack, the FME units correspond to rack mount cards installed in a rack.
OBJECT-TYPE    
  INTEGER  

mdmModem 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.2
This entry displays the index of the FME unit. It corresponds with its position in the stack.
OBJECT-TYPE    
  INTEGER  

mdmPosition 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.3
This entry displays the location of the corresponding unit: 'local' or 'remote'. The unit which belongs to a managed stack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

mdmModemName 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.5
The verbal name of this unit.
OBJECT-TYPE    
  DisplayString  


mdmAlarmConditionPort7 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.116
The alarm trigger mode at port 7: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), laser-fail(4), no-link-signal-or-laser-fail(5), not-available(100)  

mdmAlarmConditionPort8 1.3.6.1.4.1.760.1.1.2.1.10.601.1.1.117
The alarm trigger mode at port 8: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
OBJECT-TYPE    
  INTEGER other(1), disable(2), no-link-signal(3), laser-fail(4), no-link-signal-or-laser-fail(5), not-available(100)  

fmePortTable 1.3.6.1.4.1.760.1.1.2.1.10.601.2
This table contains information about all I/F ports of the FME units within all stacks.
OBJECT-TYPE    
  SEQUENCE OF  
    FmeTableEntry

fmePortEntry 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1
The index of the table.
OBJECT-TYPE    
  FmeTableEntry  

portRack 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.1
The index of the stack the port belongs to.
OBJECT-TYPE    
  INTEGER  

portModem 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.2
The index of the FME unit the port belongs to.
OBJECT-TYPE    
  INTEGER  

portPosition 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.3
This entry displays the location of the corresponding port: 'local' or 'remote'. The port which belongs to a managed stack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

portPort 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.4
The index of the port.
OBJECT-TYPE    
  INTEGER  

portInterfaceEmulationMode 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.6
Interface mode of the port: 'dte', 'dce', 'te', or 'nt'.
OBJECT-TYPE    
  INTEGER other(1), dte(2), dce(3), te(4), nt(5), unknown(99)  

mdmModemProperty 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.7
The speed class of the port: 'e1' or 't1'.
OBJECT-TYPE    
  INTEGER other(1), e1(2), t1(3), unknown(99)  

portClockSystem 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.23
The clock system at the interface port: 'single' or 'dual'. The available values depend on the interface type.
OBJECT-TYPE    
  INTEGER other(1), dual(2), single(3)  

portClockSource 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.24
The clock source at the interface port: 'internal', 'remote', or 'external'.
OBJECT-TYPE    
  INTEGER other(1), internal(2), remote(3), external(4)  

portDataRate 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.25
The data rate at the interface port in bits per seconds. The data rate at the remote counterpart changes simultaneously.
OBJECT-TYPE    
  INTEGER other(1)  

portLocalCarrierDetect 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.60
The data carrier detect mode at the interface: if set to 'fo-link-and-remote-handshake' the DCD signal (resp. I for X.21, etc.) follows link status and remote RTS (resp. C for X.21, etc.), if set to 'fo-link' the DCD signal follows link status only. Not available for units with G.703 onboard.
OBJECT-TYPE    
  INTEGER other(1), fo-link-and-remote-handshake(2), fo-link(3), not-available(100)  

portTDPhaseLocking 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.67
This entry defines the data phase locking for I/F data: 'positive-clock-slope' or 'negative-clock-slope'. For units with G.703 onboard the value 'positive-clock-slope' is valid only.
OBJECT-TYPE    
  INTEGER other(1), positive-clock-slope(2), negative-clock-slope(3), unknown(99)  

portLineBuiltOut 1.3.6.1.4.1.760.1.1.2.1.10.601.2.1.68
The G.703 transmission mode of the unit. Valid for units with G.703 onboard only.
OBJECT-TYPE    
  INTEGER other(1), itu-rec-g703(2), dsx-1-0to133-ft(3), dsx-1-133to266-ft(4), dsx-1-266to399-ft(5), dsx-1-399to533-ft(6), dsx-1-533to655-ft(7), not-available(100)  

fme-modem 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.601
OBJECT IDENTIFIER    

Defined Objects

FmeTableEntry  
SEQUENCE    
  INTEGER as mdmRack  
  INTEGER as mdmModem  
  INTEGER as mdmPosition  
  DisplayString as mdmModemName  
  INTEGER as mdmActiveLink  
  INTEGER as mdmAlarmConditionPort7  
  INTEGER as mdmAlarmConditionPort8  

FmePortEntry  
SEQUENCE    
  INTEGER as portRack  
  INTEGER as portModem  
  INTEGER as portPosition  
  INTEGER as portPort  
  INTEGER as portInterfaceEmulationMode  
  INTEGER as mdmModemProperty  
  INTEGER as portClockSystem  
  INTEGER as portClockSource  
  INTEGER as portDataRate  
  INTEGER as portLocalCarrierDetect  
  INTEGER as portTDPhaseLocking  
  INTEGER as portLineBuiltOut