
| SNMPv2-SMI | SNMPv2-TC | RAD-MIB |
| IF-MIB | SNMP-FRAMEWORK-MIB |
| OBJECT-TYPE | Integer32 | Gauge32 |
| RowStatus | TruthValue | diverseIfWanGen |
| InterfaceIndex | SnmpAdminString |
| broadbandIf | 1.3.6.1.4.1.164.3.1.6.8 | ||
| OBJECT IDENTIFIER | |||
| bdbandConfig | 1.3.6.1.4.1.164.3.1.6.8.1 | ||
| OBJECT IDENTIFIER | |||
| prtBdbandIndTable | 1.3.6.1.4.1.164.3.1.6.8.1.1 | ||
| The Indication Signal table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtBdbandIndEntry | |||
| prtBdbandIndEntry | 1.3.6.1.4.1.164.3.1.6.8.1.1.1 | ||
| An entry in the Indication Signal table. | |||
| OBJECT-TYPE | |||
| PrtBdbandIndEntry | |||
| prtBdbandCnfgIdx | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.1 | ||
| This object indicates the Idx of the Agent Cnfg the following objects refer. 255=Temporary Cnfg (when relevant, Set is done only to this configuration). For Agents that support only one configuration, this object will be constant=1. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| prtBdbandIdx | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.2 | ||
| This object indicates a unique port or interface number. For numbering, see product's spec. For some products, the numbering can equal ifIndex. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| prtBdbandIndSig | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.3 | ||
| This object indicates a unique Indication Signal. ais(1) = AIS = Alarm Indication Signal. rdi(2) = RDI = Remote Defect Indication. | |||
| OBJECT-TYPE | |||
| INTEGER | ais(1), rdi(2), aisAndRdi(3) | ||
| prtBdbandIndEvent | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.4 | ||
| This object indicates a unique Event that can cause the Indication Signal. slm(2) = SLM = Signal Label Mismatch eed(4) = EED = Excessive Error Defect pathTrace(5) = the end-to-end source/destination of information is wrong. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), slm(2), fail(3), eed(4), pathTrace(5) | ||
| prtBdbandIndSigEnable | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.5 | ||
| This object allows user to define if the event specified by prtBdbandIndEvent will cause creation of the Indication Signal specified by prtBdbandIndSig or not. disable - will not enable causing the signal enable - will enable causing the signal. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), disable(2), enable(3) | ||
| prtBdbandRowStatus | 1.3.6.1.4.1.164.3.1.6.8.1.1.1.6 | ||
| Creation/Deletion of rows in the table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| prtPhyConfigTable | 1.3.6.1.4.1.164.3.1.6.8.1.2 | ||
| The Phy Config table. Used now for Phy25.6 Mbps. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtPhyConfigEntry | |||
| prtPhyConfigEntry | 1.3.6.1.4.1.164.3.1.6.8.1.2.1 | ||
| An entry in the Phy Config table. | |||
| OBJECT-TYPE | |||
| PrtPhyConfigEntry | |||
| prtPhyTimeElapsed | 1.3.6.1.4.1.164.3.1.6.8.1.2.1.1 | ||
| The number of seconds that have elapsed since the beginning of the current error-measurement period. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..899 | ||
| prtPhyValidIntervals | 1.3.6.1.4.1.164.3.1.6.8.1.2.1.2 | ||
| The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute since the interface has been online. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..96 | ||
| prtPhyPerfHistory | 1.3.6.1.4.1.164.3.1.6.8.2 | ||
| OBJECT IDENTIFIER | |||
| prtPhyCurrentTable | 1.3.6.1.4.1.164.3.1.6.8.2.1 | ||
| The 25.6 Mbps Section/Line Current table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtPhyCurrentEntry | |||
| prtPhyCurrentEntry | 1.3.6.1.4.1.164.3.1.6.8.2.1.1 | ||
| An entry in the 25.6 Mbps Line Current table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps. | |||
| OBJECT-TYPE | |||
| PrtPhyCurrentEntry | |||
| prtPhyCurrentLOS | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.1 | ||
| The counter associated with the number of Loss Of Sync seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyCurrentLSV | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.2 | ||
| The counter associated with the number of Line symbol violation seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyCurrentUAS | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.3 | ||
| The counter associated with the number of UAS encountered by a 25.6 Mbps interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyCurrentSES | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.4 | ||
| The counter associated with the number of SES encountered by a 25.6 Mbps interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyCurrentES | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.5 | ||
| The number of Errored Seconds, encountered by a 25.6 Mbps interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyCurrentStatus | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.6 | ||
| The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| prtPhyCurrentLOF | 1.3.6.1.4.1.164.3.1.6.8.2.1.1.7 | ||
| The number of Loss of Frames, encountered by an interface in the current 15 minute interval. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalTable | 1.3.6.1.4.1.164.3.1.6.8.2.2 | ||
| The Line Interval table. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| PrtPhyIntervalEntry | |||
| prtPhyIntervalEntry | 1.3.6.1.4.1.164.3.1.6.8.2.2.1 | ||
| An entry in the 25.6 Mbps Line Interval table. ifIndex of the line 25.6 Mbps layer of type 25.6 Mbps. | |||
| OBJECT-TYPE | |||
| PrtPhyIntervalEntry | |||
| prtPhyIntervalNumber | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.1 | ||
| A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | |||
| OBJECT-TYPE | |||
| Integer32 | 1..96 | ||
| prtPhyIntervalLOS | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.2 | ||
| The counter associated with the number of Loss Of Sync seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalLSV | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.3 | ||
| The counter associated with the number of line symbol violation seconds , encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalUAS | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.4 | ||
| The counter associated with the number of UAS encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalSES | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.5 | ||
| The counter associated with the number of SES encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalES | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.6 | ||
| The number of Errored Seconds, encountered by a 25.6 Mbps interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| prtPhyIntervalStatus | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.7 | ||
| The statuses of the current interval: 0 - O.K. 1 - The link has been switched by a redundancy mechanism. 2 - Module is in/out. 4 - Empty - card is out. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(4) | ||
| prtPhyIntervalLOF | 1.3.6.1.4.1.164.3.1.6.8.2.2.1.8 | ||
| The number of Loss of Frames, encountered by an interface in one of the previous 96, individual 15 minute intervals. | |||
| OBJECT-TYPE | |||
| Gauge32 | |||
| r2If | 1.3.6.1.4.1.164.3.1.6.9 | ||
| OBJECT IDENTIFIER | |||
| r2ProfileCnfg | 1.3.6.1.4.1.164.3.1.6.9.1 | ||
| OBJECT IDENTIFIER | |||
| r2CnfgTable | 1.3.6.1.4.1.164.3.1.6.9.1.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| R2CnfgEntry | |||
| r2CnfgEntry | 1.3.6.1.4.1.164.3.1.6.9.1.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| R2CnfgEntry | |||
| r2CnfgIdx | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.1 | ||
| This attribute indicates the Idx of the Cnfg being accessed. 255 = TmpCnfg. 1 = Current Cnfg. Write is allowed only to TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| r2CnfgProfileIdx | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.2 | ||
| Profile Index. Valid values: 1..5 Only instances of profiles that are defined having agnSigProfType=r2Cas will exist in this table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2Mode | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.3 | ||
| R2 Mode. auto - in this mode, default value of timers will be used by R2, according to the selected r2Country. manual - in this mode, user can change the value of R2 timers within the valid limits, specific to each country. | |||
| OBJECT-TYPE | |||
| INTEGER | auto(2), manual(3) | ||
| r2Country | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.4 | ||
| R2 Country. R2 Timers can have different range of values and defaults for each country. When r2Mode=auto, the default value is used by R2 according to this selected country. 1=ITU-T (standard values) 2=Korea 3=India 4=Brasil (continuous) 5=Brasil (pulsed) 6..10 - reserved for future countries. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2Delay | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.5 | ||
| This object enables user to configure the link as satellite or terrestrial. The seize acknowledge detect timing is much shorter (msec) for terrestrial link than for satellite link (1-2 sec). | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), terrestrial(2), satellite(3) | ||
| r2MeteringInd | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.6 | ||
| Which Bit will be used for Metering Indication. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), cBit(2), bBit(3) | ||
| r2BreakMakeRatio | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.7 | ||
| This object describes the Break-Make Ratio of Pulse Duration, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), break56Make44(2), break64Make36(3), break80Make20(4) | ||
| r2ReleaseGuardT2 | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.8 | ||
| Release Guard timing T2. Release guard timing before going to idle, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2Regret | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.9 | ||
| Regret duration, in [sec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2SeizeDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.10 | ||
| Seize Detect. Timer of the R2 incoming side. Minimum duration to detect a valid seizure, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2SeizeAckDelay | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.11 | ||
| Timer of the R2 incoming side. Delay before sending a valid seize ack signal, in [msec]. Applicable only when r2Mode=manual. only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2ClearBackDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.12 | ||
| Timer of the R2 incoming side. Minimum duration to recognize a valid clear-back, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2ClearFwdDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.13 | ||
| Timer of the R2 incoming side. Minimum duration to recognize a valid clear-forward, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2FaultDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.14 | ||
| Timer of the R2 incoming side. Minimum duration to recognize a block signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2FaultRemoveDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.15 | ||
| Timer of the R2 incoming side. Minimum duration to recognize a valid block removal signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2MeterPulseDuration | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.16 | ||
| Timer of the R2 incoming side. Duration of metering pulse to be sent, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2SeizeAckWait | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.17 | ||
| Timer of the R2 outgoing side. Minimum duration to receive seizure acknowledge signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2SeizeAckDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.18 | ||
| Timer of the R2 outgoing side. Minimum duration to recognize a valid seizure acknowledge signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2AnswerDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.19 | ||
| Timer of the R2 outgoing side. Minimum duration to recognize a valid answer signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2BlockRemoveDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.20 | ||
| Timer of the R2 outgoing side. Minimum duration to recognize a valid block removal signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2MeterPulseDetect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.21 | ||
| Timer of the R2 outgoing side. Minimum duration of incoming meter pulse, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2ForcedDisconnect | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.22 | ||
| Timer of the R2 outgoing side. Minimum duration to recognize disconnect signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2DisconnectAck | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.23 | ||
| Timer of the R2 outgoing side. Minimum duration to recognize disconnect acknowledge signal, in [msec]. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2ReleaseGuardT1 | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.24 | ||
| Timer of the R2 outgoing side. Minimum duration to release guard, in [msec]. During this time, no new call can be initiated. RW only when r2Mode=manual. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2CnfgRowStatus | 1.3.6.1.4.1.164.3.1.6.9.1.1.1.25 | ||
| This object enables the user to add/delete entries to/from the table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| r2TsTable | 1.3.6.1.4.1.164.3.1.6.9.1.2 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| R2TsEntry | |||
| r2TsEntry | 1.3.6.1.4.1.164.3.1.6.9.1.2.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| R2TsEntry | |||
| r2TsCnfgIdx | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.1 | ||
| This attribute indicates the Idx of the Cnfg being accessed. 255 = TmpCnfg. 1 = Current Cnfg. Write is allowed only to TmpCnfg. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..255 | ||
| r2TsProfileIdx | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.2 | ||
| Profile Index. Valid values: 1..5 Only instances of profiles that are defined having agnSigProfType=r2Cas will exist in this table. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2TsIdx | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.3 | ||
| TS Index. Valid values: 1..31 | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2TsCallEnable | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.4 | ||
| This object indicates the Enabled Call direction for the specific TS. | |||
| OBJECT-TYPE | |||
| INTEGER | incoming(2), outgoing(3), both(4) | ||
| r2TsMetering | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.5 | ||
| This object indicates if the specific TS should support Metering. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| r2TsRowStatus | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.6 | ||
| This object enables the user to add/delete entries to/from the table. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| r2TsReversePolarity | 1.3.6.1.4.1.164.3.1.6.9.1.2.1.7 | ||
| This object indicates if the specific TS should support Reverse Polarity. | |||
| OBJECT-TYPE | |||
| INTEGER | no(2), yes(3) | ||
| r2IfStatus | 1.3.6.1.4.1.164.3.1.6.9.2 | ||
| OBJECT IDENTIFIER | |||
| r2StatusTable | 1.3.6.1.4.1.164.3.1.6.9.2.1 | ||
| The write operation into the Table Objects is valid only to the TmpCnfg entry. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| R2StatusEntry | |||
| r2StatusEntry | 1.3.6.1.4.1.164.3.1.6.9.2.1.1 | ||
| An entry in table. | |||
| OBJECT-TYPE | |||
| R2StatusEntry | |||
| r2StatusSlotIdx | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.1 | ||
| Slot Index | |||
| OBJECT-TYPE | |||
| INTEGER | io1(5), io2(6), io3(7), io4(8), io5(9), io6(10), io7(11), io8(12), io9(13), io10(14), io11(15), io12(16), notApplicable(255) | ||
| r2StatusPortIdx | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.2 | ||
| This object indicates a unique port number of the ML having R2 interface. Valid values: exPrt1 (1)..exPrt4 (4) | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| r2StatusTsIdx | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.3 | ||
| Time Slot index. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..31 | ||
| r2StatusSigDirection | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.4 | ||
| R2 Time Slot Signaling Direction. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), incoming(2), outgoing(3) | ||
| r2StatusTsState | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.5 | ||
| R2 TS State | |||
| OBJECT-TYPE | |||
| INTEGER | notUsed(1), normal(2), remoteBlocked(3), localBlocked(4), localLoop(5), remoteLoop(6) | ||
| r2StatusProtocolState | 1.3.6.1.4.1.164.3.1.6.9.2.1.1.6 | ||
| R2 Protocol State. | |||
| OBJECT-TYPE | |||
| INTEGER | idle(1), seized(2), seizureAcknowledged(3), answered(4), clearForward(5), clearBack(6), blocked(7), forcedDisc(8), doubleSeizure(9), fault(10), discAcknowledged(11), fault1(12), fault6(13), fault3(14) | ||
| atmLayer2 | 1.3.6.1.4.1.164.12.7 | ||
| OBJECT IDENTIFIER | |||
| atmLayer2XVclTable | 1.3.6.1.4.1.164.12.7.1 | ||
| This table is an extension of VCL table, which is created for each LAN VCC. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmLayer2XVclEntry | |||
| atmLayer2XVclEntry | 1.3.6.1.4.1.164.12.7.1.1 | ||
| Conceptual row in atmVclTable. This table augments the RFC2515 VCL table. | |||
| OBJECT-TYPE | |||
| AtmLayer2XVclEntry | |||
| atmLayer2XVclConnMode | 1.3.6.1.4.1.164.12.7.1.1.1 | ||
| Each valid LAN VCC is either Main or Sub. This parameter is configured only once on creation of a LAN VCC. It can not be changed after creation. In order to change the Mode, user should delete the connection and create a new one. main - A LAN VCC, which holds its own bridge port. Bridge forwarding and Bridge learning is performed only on Main VCCs. For working on a transparent bridge, that doesn't perform layer 2 priority mapping, a Main VCC should be opened, which is the default connection Mode. When working with layer 2 priority, a group of LAN VCCs should be configured, where each group will be associated with only one Main VCC. A specific Main can not be used by more than one group. sub - A LAN VCC is not part of the bridging mechanism. A Sub VCC automatically inherit some general definitions from Main VCC of its group: ATM Slot/Port and LAN Slot/Port. Max number of Sub VCCs allowed per group is: [Number of Priorities - 1]. | |||
| OBJECT-TYPE | |||
| INTEGER | main(1), sub(2) | ||
| atmLayer2XVclGroupIdx | 1.3.6.1.4.1.164.12.7.1.1.2 | ||
| The group identifier. A VCC Group identifier = 0 if the VCC was not associated with a group yet. This value is updated according to the group identifier set by atmLayer2GroupTable. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmLayer2GroupTable | 1.3.6.1.4.1.164.12.7.2 | ||
| This table contains groups and their members. A group is a bundle of VCCs, which acts as different queues. Main and Sub VCCs should have the same ATM slot and port, and the same LAN slot and port. Each group contains: 1 to VCCs. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmLayer2GroupEntry | |||
| atmLayer2GroupEntry | 1.3.6.1.4.1.164.12.7.2.1 | ||
| Conceptual row in atmLayer2GroupTable. The indexes: ifIndex, atmVclVpi and atmVclVci indicate the Network ATM End-Point. Upon a group creation, one Main VCC must be added first. After the group was created, Sub VCCs may be added to the group. | |||
| OBJECT-TYPE | |||
| AtmLayer2GroupEntry | |||
| atmLayer2GroupIdx | 1.3.6.1.4.1.164.12.7.2.1.1 | ||
| The group identifier. 0 is not a valid index. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmLayer2GroupRowStatus | 1.3.6.1.4.1.164.12.7.2.1.2 | ||
| Creation/Deletion of rows in the table, and indication of the entry's status. | |||
| OBJECT-TYPE | |||
| RowStatus | |||
| atmLayer2GroupConnMode | 1.3.6.1.4.1.164.12.7.2.1.3 | ||
| Each valid LAN VCC is either Main or Sub as configured in atmLayer2XVclTable. | |||
| OBJECT-TYPE | |||
| INTEGER | main(1), sub(2) | ||
| atmLayer2GroupConnPriority | 1.3.6.1.4.1.164.12.7.2.1.4 | ||
| This parameter is configured by atmLayer2PriorityRx from atmLayer2PriorityTable. Each bit in the Octet represents a specific priority as follows: MSB 7 6 5 4 3 2 1 0 LSB -> Priorities |--------------------| 1 0 0 1 0 0 0 1 -> Value In this example, a certain VCC has several priorities: 0, 4 and 7. | |||
| OBJECT-TYPE | |||
| OCTET STRING | SIZE(1) | ||
| atmLayer2GroupName | 1.3.6.1.4.1.164.12.7.2.1.5 | ||
| Group name. Configured by the user. The name is unique per system. For atmLayer2GroupIdx=0, the name will be null. | |||
| OBJECT-TYPE | |||
| SnmpAdminString | SIZE(1..32) | ||
| atmLayer2PriorityTable | 1.3.6.1.4.1.164.12.7.3 | ||
| This table maps all priorities inside a group. Several priorities might be mapped to the same VCC. Upon priority change, the agent will update the VCCs of the changed priority in this table, and will update - atmLayer2GroupConnPriority parameter of both former and new owners of the changed priority. Changing a VCC value is actually a change of three parameters simultaneously: atmLayer2PriorityIfIndex, atmLayer2PriorityVclVpi and atmLayer2PriorityVclVci. Otherwise, the set will be rejected, since there might be that such VCC doesn't exist in the specific group. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmLayer2PriorityEntry | |||
| atmLayer2PriorityEntry | 1.3.6.1.4.1.164.12.7.3.1 | ||
| Conceptual row in atmLayer2PriorityTable. Each entry is a Network ATM End-Point per priority. Upon a group creation, all priorities are mapped to the Main VCC. Number of entries per group is according to the number of priorities enabled. (For example, for Max priorities = 8, the agent will create 8 entries). | |||
| OBJECT-TYPE | |||
| AtmLayer2PriorityEntry | |||
| atmLayer2PriorityGroupIdx | 1.3.6.1.4.1.164.12.7.3.1.1 | ||
| The group identifier. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmLayer2PriorityRx | 1.3.6.1.4.1.164.12.7.3.1.2 | ||
| The priority values. The used values are 0-7, but since this value is part of the index of the table, and in order to avoid '0' as an index, the index syntax is 1..8, but the real value is atmLayer2PriorityRx-1: 0 - for Low priority. 7 - for High priority. | |||
| OBJECT-TYPE | |||
| Integer32 | 1..8 | ||
| atmLayer2PriorityIfIndex | 1.3.6.1.4.1.164.12.7.3.1.3 | ||
| ATM ifIndex of the network End-Point. | |||
| OBJECT-TYPE | |||
| InterfaceIndex | |||
| atmLayer2PriorityVclVpi | 1.3.6.1.4.1.164.12.7.3.1.4 | ||
| Vpi of the network End-Point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmLayer2PriorityVclVci | 1.3.6.1.4.1.164.12.7.3.1.5 | ||
| Vci of the network End-Point. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| atmLayer2GroupIndexNext | 1.3.6.1.4.1.164.12.7.4 | ||
| This object contains an appropriate value to be used for atmLayer2GroupIdx when creating entries in the atmLayer2GroupTable. The value 0 indicates that no unassigned entries are available. To obtain the atmLayer2GroupIdx value for a new entry, the manager gets the current value of this object. The next index will be of the first unassigned entry. It will be provided by checking the assigned entries. | |||
| OBJECT-TYPE | |||
| Integer32 | 0..2147483647 | ||
| atmLayer2CfgTable | 1.3.6.1.4.1.164.12.7.5 | ||
| Bridge configuration Table. This table supports multi-bridge and bridge features within an ATM device. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| AtmLayer2CfgEntry | |||
| atmLayer2CfgEntry | 1.3.6.1.4.1.164.12.7.5.1 | ||
| Conceptual row in atmLayer2CfgTable. Each entry in this table contains the bridging attributes for both Ethernet and ATM sides. The interface index is the Ethernet port interface. For Ace52: this object represents the Bridge ifIndex. | |||
| OBJECT-TYPE | |||
| AtmLayer2CfgEntry | |||
| atmLayer2CfgBridgingMode | 1.3.6.1.4.1.164.12.7.5.1.1 | ||
| Bridging mode can be one of the following: ATM <> Ethernet - Bridging is between the Ethernet port and the ATM port (there is no bridging between VCs). ATM <> Ethernet + ATM - Bridging is done both between the Ethernet port and the ATM port and also between VCs. | |||
| OBJECT-TYPE | |||
| INTEGER | accessOnly(1), accessAndSwitching(2) | ||
| atmLayer2CfgVlanMode | 1.3.6.1.4.1.164.12.7.5.1.2 | ||
| VLAN Mode. Upon Mode changing, all LAN VCCs will be deleted by the agent from all tables that include LAN VCCs. | |||
| OBJECT-TYPE | |||
| INTEGER | disable(2), enable(3) | ||
| atmLayer2CfgAtmAcceptableFrameType | 1.3.6.1.4.1.164.12.7.5.1.3 | ||
| The Frame Type that will be acceptable by the VCCs that are associated with this Ethernet port. Frames which don't match the selected type will be discarded. admitAll - all frames will be accepted. admitOnlyVlanTagged - only Tagged frames will be accepted. admitOnlyUnTagged - only unTagged frames will be accepted. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), admitAll(2), admitOnlyVlanTagged(3), admitOnlyUnTagged(4) | ||
| atmLayer2CfgAtmIngressFiltering | 1.3.6.1.4.1.164.12.7.5.1.4 | ||
| For the VCCs that are associated with this Ethernet port, when this is true(1) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When false(2), the port will accept all incoming frames. | |||
| OBJECT-TYPE | |||
| TruthValue | |||
| atmLayer2CfgAtmTxFrameType | 1.3.6.1.4.1.164.12.7.5.1.5 | ||
| The Frame Type that will be transmitted by the VCCs that are associated with this Ethernet port. unTagged - The transmitted frames will be unTagged. tagged - The transmitted frames will be Tagged. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), unTagged(2), tagged(3) | ||
| atmLayer2CfgEthAcceptableFrameType | 1.3.6.1.4.1.164.12.7.5.1.6 | ||
| The Frame Type that this Ethernet port will accept. (for ACE-52: the Frame Type that this Bridge will accept) This parameter is notApplicable for atmLayer2VlanMode=disable. Frames which don't match the selected type will be discarded. admitAll - all frames will be accepted. admitOnlyVlanTagged - only Tagged frames will be accepted. admitOnlyUnTagged - only unTagged frames will be accepted. | |||
| OBJECT-TYPE | |||
| INTEGER | notApplicable(1), admitAll(2), admitOnlyVlanTagged(3), admitOnlyUnTagged(4) | ||
| atmLayer2CfgBridgeAction | 1.3.6.1.4.1.164.12.7.5.1.7 | ||
| This object enables to perform the specified action on the selected port. | |||
| OBJECT-TYPE | |||
| INTEGER | deleteLanTable(7), noOp(255) | ||
| atmLayer2CfgLearningMode | 1.3.6.1.4.1.164.12.7.5.1.8 | ||
| This object specifies the mode of the learning process of a bridge. svl - Shared VLAN process. If an individual MAC Address is learned in one VLAN, this information is used in forwarding decisions taken for that address for all other VLANs. ivl - Independent VLAN process. If an individual MAC Address is learned in one VLAN, this information is not used in forwarding decisions taken for that address for all other VLANs. | |||
| OBJECT-TYPE | |||
| INTEGER | svl(1), ivl(2) | ||
| atmLayer2CfgAgingTime | 1.3.6.1.4.1.164.12.7.5.1.9 | ||
| The timeout period in seconds for aging out dynamically learned forwarding information. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| radAtmFr | 1.3.6.1.4.1.164.12.8 | ||
| OBJECT IDENTIFIER | |||
| frAtmIwfXConnectionTable | 1.3.6.1.4.1.164.12.8.1 | ||
| This table is an extension of frAtmIwfXConnectionTable from RFC2955. | |||
| OBJECT-TYPE | |||
| SEQUENCE OF | |||
| FrAtmIwfXConnectionEntry | |||
| frAtmIwfXConnectionEntry | 1.3.6.1.4.1.164.12.8.1.1 | ||
| Conceptual row in frAtmIwfXConnectionTable. This table augments the RFC2955. | |||
| OBJECT-TYPE | |||
| FrAtmIwfXConnectionEntry | |||
| frAtmIwfXConnMode | 1.3.6.1.4.1.164.12.8.1.1.1 | ||
| FR IWF Mode. service - Service InterWorking (FRF.8), network - Network InterWorking (FRF.5). | |||
| OBJECT-TYPE | |||
| INTEGER | service(1), network(2) | ||
| frAtmIwfXConnSscsDlci | 1.3.6.1.4.1.164.12.8.1.1.2 | ||
| This parameter is relevant for frAtmIwfXConnMode=network (FRF.5) only. This parameter allow configuration of the FR SSCS DLCI that is transferred to the remote FR unit. | |||
| OBJECT-TYPE | |||
| Integer32 | |||
| PrtBdbandIndEntry | |||
| SEQUENCE | |||
| Integer32 as prtBdbandCnfgIdx | |||
| Integer32 as prtBdbandIdx | |||
| INTEGER as prtBdbandIndSig | |||
| INTEGER as prtBdbandIndEvent | |||
| INTEGER as prtBdbandIndSigEnable | |||
| RowStatus as prtBdbandRowStatus | |||
| PrtPhyConfigEntry | |||
| SEQUENCE | |||
| Integer32 as prtPhyTimeElapsed | |||
| Integer32 as prtPhyValidIntervals | |||
| PrtPhyCurrentEntry | |||
| SEQUENCE | |||
| Gauge32 as prtPhyCurrentLOS | |||
| Gauge32 as prtPhyCurrentLSV | |||
| Gauge32 as prtPhyCurrentUAS | |||
| Gauge32 as prtPhyCurrentSES | |||
| Gauge32 as prtPhyCurrentES | |||
| OCTET STRING as prtPhyCurrentStatus | |||
| Gauge32 as prtPhyCurrentLOF | |||
| PrtPhyIntervalEntry | |||
| SEQUENCE | |||
| Integer32 as prtPhyIntervalNumber | |||
| Gauge32 as prtPhyIntervalLOS | |||
| Gauge32 as prtPhyIntervalLSV | |||
| Gauge32 as prtPhyIntervalUAS | |||
| Gauge32 as prtPhyIntervalSES | |||
| Gauge32 as prtPhyIntervalES | |||
| OCTET STRING as prtPhyIntervalStatus | |||
| Gauge32 as prtPhyIntervalLOF | |||
| R2CnfgEntry | |||
| SEQUENCE | |||
| Integer32 as r2CnfgIdx | |||
| Integer32 as r2CnfgProfileIdx | |||
| INTEGER as r2Mode | |||
| Integer32 as r2Country | |||
| INTEGER as r2Delay | |||
| INTEGER as r2MeteringInd | |||
| INTEGER as r2BreakMakeRatio | |||
| Integer32 as r2ReleaseGuardT2 | |||
| Integer32 as r2Regret | |||
| Integer32 as r2SeizeDetect | |||
| Integer32 as r2SeizeAckDelay | |||
| Integer32 as r2ClearBackDetect | |||
| Integer32 as r2ClearFwdDetect | |||
| Integer32 as r2FaultDetect | |||
| Integer32 as r2FaultRemoveDetect | |||
| Integer32 as r2MeterPulseDuration | |||
| Integer32 as r2SeizeAckWait | |||
| Integer32 as r2SeizeAckDetect | |||
| Integer32 as r2AnswerDetect | |||
| Integer32 as r2BlockRemoveDetect | |||
| Integer32 as r2MeterPulseDetect | |||
| Integer32 as r2ForcedDisconnect | |||
| Integer32 as r2DisconnectAck | |||
| Integer32 as r2ReleaseGuardT1 | |||
| RowStatus as r2CnfgRowStatus | |||
| R2TsEntry | |||
| SEQUENCE | |||
| Integer32 as r2TsCnfgIdx | |||
| Integer32 as r2TsProfileIdx | |||
| Integer32 as r2TsIdx | |||
| INTEGER as r2TsCallEnable | |||
| INTEGER as r2TsMetering | |||
| RowStatus as r2TsRowStatus | |||
| INTEGER as r2TsReversePolarity | |||
| R2StatusEntry | |||
| SEQUENCE | |||
| INTEGER as r2StatusSlotIdx | |||
| Integer32 as r2StatusPortIdx | |||
| Integer32 as r2StatusTsIdx | |||
| INTEGER as r2StatusSigDirection | |||
| INTEGER as r2StatusTsState | |||
| INTEGER as r2StatusProtocolState | |||
| AtmLayer2XVclEntry | |||
| SEQUENCE | |||
| INTEGER as atmLayer2XVclConnMode | |||
| Integer32 as atmLayer2XVclGroupIdx | |||
| AtmLayer2GroupEntry | |||
| SEQUENCE | |||
| Integer32 as atmLayer2GroupIdx | |||
| RowStatus as atmLayer2GroupRowStatus | |||
| INTEGER as atmLayer2GroupConnMode | |||
| OCTET STRING as atmLayer2GroupConnPriority | |||
| SnmpAdminString as atmLayer2GroupName | |||
| AtmLayer2PriorityEntry | |||
| SEQUENCE | |||
| Integer32 as atmLayer2PriorityGroupIdx | |||
| Integer32 as atmLayer2PriorityRx | |||
| InterfaceIndex as atmLayer2PriorityIfIndex | |||
| Integer32 as atmLayer2PriorityVclVpi | |||
| Integer32 as atmLayer2PriorityVclVci | |||
| AtmLayer2CfgEntry | |||
| SEQUENCE | |||
| INTEGER as atmLayer2CfgBridgingMode | |||
| INTEGER as atmLayer2CfgVlanMode | |||
| INTEGER as atmLayer2CfgAtmAcceptableFrameType | |||
| TruthValue as atmLayer2CfgAtmIngressFiltering | |||
| INTEGER as atmLayer2CfgAtmTxFrameType | |||
| INTEGER as atmLayer2CfgEthAcceptableFrameType | |||
| INTEGER as atmLayer2CfgBridgeAction | |||
| INTEGER as atmLayer2CfgLearningMode | |||
| Integer32 as atmLayer2CfgAgingTime | |||
| FrAtmIwfXConnectionEntry | |||
| SEQUENCE | |||
| INTEGER as frAtmIwfXConnMode | |||
| Integer32 as frAtmIwfXConnSscsDlci | |||